Scribd
Upload
52 views2 pages

VERSEP

This document contains input fields and calculations for designing a two-phase vertical separator. It includes inputs for operating conditions, flow rates, densities, dimensions, materials and stresses. Calculations are shown for gas and liquid velocities, diameters, heights and volumes.

Uploaded by

Zafary Dexirus
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
52 views2 pages

VERSEP

This document contains input fields and calculations for designing a two-phase vertical separator. It includes inputs for operating conditions, flow rates, densities, dimensions, materials and stresses. Calculations are shown for gas and liquid velocities, diameters, heights and volumes.

Uploaded by

Zafary Dexirus
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd

TWO-PHASE VERTICAL SEPARATOR CALCULATION

input input input input input input input Equipment N0. Service
OPERATING PRESSURE OPERATING TEMPERATURE Gas Mass Flow rate Actual Gas Density Gas Molecular Weight Standard Gas Volume Flow Rate Actual Gas Volume Flow Rate

input input

Total Liquid Mass Flow rate Actual Liquid Density Total Liquid Volume Flow Rate

input

Demister Critical Velocity (liquid Settling velocity)

Compresor Discharge Drum (One for 2 Trains) b.a 14.42 deg.C -3.75 kg/h 2025.33 kg/m3 9.14 14.89 Sm3/d 77348 m3/s 0.06155 kg/h 1012.66 kg/m3 914.61 m3/mn 0.0185 BPD 167 y Enter y or n m/s 0.4777 0.25 0.1194 0.5153 810 86.90 3.000 cs 1220 100 33.137 876 900 34.165 832 0.5432 400 100 716 1216 1216 1248 1 0.0185 34 2 0.0369 68 1 0.0185 34 b 150 2749 900 832 2749 3.31
Ver Dibujo pagina 2

input

K Velocity Factor GasVelocity Calculated Gas Flow Area Calculated Inside Diameter

input input input input

Design Pressure Corrosion Allowance Steel Material Maximum Stress Joint Efficiciency Calculated Thickness(with Corrosion Allowance) (Warning for thickness >150 mm) Calculated Outside Diameter Standard Outside Diameter Actual Thickness (with Corrosion Allowance) Actual Inside diameter Actual gas Flow Area

m/s m2 mm b.g mm b.g 0/0 mm mm mm mm mm m2 mm mm mm mm mm mm


minute

Enter cs or ss Enter 100 or 85

Heights (see Drawing) h1 h2 h3 Calculated (h1+h2+h3) Required Actual (h1+h2+h3) h4 input


Liquid Surge Time between LAH and LSHH

Required Liquid Volume h5 input


Liquid Surge Time between LAH and LAL

m3 mm
minute

Required Liquid Volume h6 input


Liquid Surge Time between LAL and LSLL

m3 mm
minute

input

Required Liquid Volume h7 LT connection h8 Total Height FINAL RESULTS OUTSIDE DIAMETER INSIDE DIAMETER LENGTH (s/s) Length/Outside Ratio

m3 mm mm mm mm mm mm

Enter b or s
(bottom or side connection)

K Velocity Factor DEMISTER NO DEMISTER Fuel gas Drum 1.7 0.8 Compressor Suction Drum 1.7 0.8 Feed KO Drum 1.7 0.8 (with Foaming Risk) Reflux Drum 2.2 1.7 Production Separator 2.2 1.7 El valor de BROWN-SOUDERS para calcular la "Settling Velocity" de los liquido es de 0.048 m/s. Se aplica a este valor un factor de multiplicacion : el factor de Velocidad K

You might also like