uF ) Find: Ne. u/w. Headquarters Office/ Weuret arate Works Branch/ Sarat rat Chennai - 600 003/axg-3 ADt/ferie: 17.04.2014 M4 3 CAOICNIERS, CAO/CNIMS, CBE/MAS & CPM/RVNL/Chennai [Link]/Co-ord./MAS, SA, PGT, TVC,TPJ & MDU ag) TT PITTE, Way, dete, chit, Hae ws, Principal/SRCETC/TBM Sub: Continuation of LWR/CWR over ballasted deck bridges on Indian Railways. Ref: DG/Track/RDSO letter [Link]/IM/LWR (Part) dated 19/26.03.2014 8& && BR ED/Track/RDSO vide letter cited reference have issued “Instructions on continuation of LWR/CWR on ballasted deck bridges with bearings on Indian Railways” as Annecure-I and the special maintenance instruction for bridges where LWRICWR is continued has been framed by RDSO and enclosed as Annexure-lI. The copies of instructions in Annexure | & Il is enclosed for information and necessary action please. Encl: 1 RDSO letter along with Annexure-! & | [fsa _ i. (RP. wmalg a 7 [Link]/TMS For Principal Chief Engineer SOUTHERN RAILWAY) xf 2a Sate Suy/ Corxdionn -glb. 15-04-20! te _ADENS .& SSE [Pw ban noes sears oe ners me ada, C/- 81. DENI[E[MDY , DEN feouk pad, Oqauy * enNOt. IMDU, Denjweks [MOY are DENI] lo ode MDG Wway — Fax" (oeaal 2064 ae a2) 245310 \ ety pe No. CT/IM/LWR (Part) & " To ‘A. 1.0 2.0 3.0 4.0 P dow sore rer = ‘Government of Indi- Ministry of Rays * gegiers aPreet ate sre geet > Rete & Stands Ormiston wars - 26011 1 ‘aeknow 236 01 i 523) 245018, Principal Chief Engineer, S~ >i: = 4.42 All Zonal Railways (as per melling lit) Sub.: Continuation of LWR/CWR areca deck bridges on Indian Railways. Railway Board letter no. 2011/CE-IV/TK/LWR, dated 05.02.2014, Based on recommendations of Track Standard Committee during 78" meeting, an HAG committee was nominated vide Railway Board letter no. 2007/CE-/TSC/1 dated 19.08.08. The committee submitted the report vide letter no. CT/M/LWR/Part dated 08.07.2013. Railway Board vide letter no. 2011/CE-IVTK/LWR dated 24.09.13 have approved the recommendation made by HAG committee for continuation of LWR on ballasted_deck ri Teport oF committee and directed to circulate the approved instructions to all Zonal Railways for compliance “Instructions on continuation- of LWR/CWR on ballasted deck bridges with bearings on Indian Railways” as approved by Railway Board vide letter referred above is enclosed as Annexure-l. In compliance to instructions contained in lelter under reference, the special maintenance instructions for bridges where LWRICWR is continued as per these provisions has been framed and is enclosed as Annexure-Il. These instructions are only indicative and will be reviewed based on results of instrumentation and feedback from Zonal Railways. Further necessary action shall be taken by Zonal Railways in this regard, DA: As above. \ aA, wy Copy to: (Satish Kumar Pandey) Executive Director/Track-| for Director General/Track ) Director/IRICEN, Pune for information. (ii) Executive Director/Civil Engineering/Planning, Railway Board, New Delhi for information. ) Executive Director/B&S/RDSO for information and necessary action. JeAnnexure- | uation of .WR/CWR on Ballasted Deck Bridges Subject: Instructions for cont with bearings on Indian Railw LWRICWR can be continued, with approval of Principal chief Engineer, as trial on Ballasted deck Bridges up to total bridge length of 110m on Tangent track, subject to the following. 1 1.1 Individual Span: [Link] span does not exceed 24.4 m, if bearings are of fixed and free type (such as roller/rocker or POT-PTFE type). 1.1.2 Individual span does not exceed 45.7 m, if elastomeric bearings without restraint in longitudinal direction are used. 1.1.3 Total length of bridge from abutment to abutment does not exceed 110m, 1.2 Track Structure’ 1.2.1 Track structure on bridges consists of minimum 52 Kg 90 UTS rails, PRC sleepers with elastic fastenings and density 1540 nos/KM. 1.2.2 Full ballast cushion as per provisions of IRPWM is available on bridge and approaches, 1.2.3 The track alignment on the bridge is straight. 1.2.4 There is no Switch Expansion Joint within 100 m on either side approach of the bridge. 5 1.2.5 Full component of fitings in track on bridge proper and 100 m on either side approach of the bridge is ensured. 1.2.6 All welds on bridge and 100 m approaches on either side are joggle fish plated with clamps or two far end bolts. 1.3 Other Stipulations: carried out on bridge and 100 m approaches on either side as per 1.3.1 USFD testing provisions of Manual for _Uiitrasonic Testing of Rails and Welds 2042 with tatest—. correction slip and corrective action is ensured. 1.3.2 The loads plying on the bridge are not heavier than MBG 1987 (including CC +8 +2 axle loads). 1.3.3 The other general provisions of Manual for LWR and IRPWM are complied with and there shall not be any unusual/ recurring problem with the bridge superstructure/ substructure/ bearings or track/formation on bridge and within a distance of 100 m on either side of the bridge 1.3.4 The LWR/bridge shall be kept under observation and inspected at officer level at least once in a month for proper behavior of LWR and bridge. hall 2. Prineipal Chief Engineer of zonal railway, before permitting continuation of LW ensure check of bridge structure including bearings and rail stresses for rail-structure interaction effect as per advance correction slip no 45 to IRS Bridge Rules. The parameters defined in clause 2.8 24 3. as amended vide correction slip no 45, of IRS Bridge Rules shall geover-ride any provision in UIC-774-3R, wherever in deviation. The check shall be done using graphs given in UIC leafiet. Alternately, detailed computer analysis as laid down in UIC-774- 3R may also be used. No limits for vertical bending of deck have been specified. This check, may not be done in the trial bridges. The initial one or two bridges selected for continuation of LWR on trial shall be instrumented as per scheme enclosed as Annexure A. The results of instrumentation and reports shall be advised to RDSO for analysis and acceptance. 4. B &S Directorate of RDSO shall be approached for any clarifications in this regard,Annexure A Instrumentation scheme for specified bridges Long Welded Ralll/ Continuous welded Rail (LWR/CWR) as defined in LWR manual shall be continued on a bridge only after permission of Principal Chief Engineer (PCE). PCE while permitting continuation of LWR, on trial, will satisfy himself that the computations have been done as per para [Link].3 incorporated vide correction slip no 45 to IRS Bridge Rules and the bridge has been found safe from longitudinal forces point of view, the rotations/ deflections of the structure are within limits specified in the UIC 774-3R and the additional stresses in rails due to LWR/CWR are within limits specified in IRS Bridge Rules para 28.243. .._ In order to validate the assumptions of UIC leaflet for broad gauge track on Indian Railways, it is essential the results of detailed analysis are compared and verified with results obtained after detailed instrumentation. Thus, instrumentation is to be done for initial one or two bridges on each Zonal Railway, where continuation of LWR is planned. For such bridges, the analysis of Rail-Bridge interaction shall be done using FEM analysis software using _ “parameters specified in IRS Bridge Rules para [Link].3 and UIC 774-3R. Any software used must be validated to be as per provisions of UIC 774-3R. Guidance assistance of B & S Directorate of RDSO shall be taken in carrying out the analysis. L 3. The criteria for choosing the bridge to be instrumented shall be as follows: a. Complete design/ drawings of the bridge shall be available. Bridge shall have multiple simply supported ballasted deck concrete/ stee-RCC b. composite spans. c. The height of piers shall not be too less nor shall it be too much. Height in the range of 4 ‘mto 10m shall be most suitable. d. At the fixed end of the girder, space shall be available for fixing the reaction frame etc required for instrumentation. -4,—Before-start-of testing, the fottowing actiorris to be taken The design and details of the bridge shall be collected by design office and computations of raikbridge interaction shall be done to determine whether the bridge is suitable for continuing the LWR/CWR or not. Details of any repairs/ rehabilitation of the elements of bridge shall also be collected and their effect on performance of the bridge shall be assessed. B & S directorate of RDSO shall be consulted for carrying out the computations. b. Additional free bearings (Roller or POT-PTFE) along with properly designed reaction frame shall be got fabricated as described in instrumentation scheme (para 5 (c) below) or action may be taken as per the instrumentation scheme finalized ¢. Instrumentation work shall continue for minimum six months so as to cover the hottest and coldest months in a year. d. Test trains with known actual axle loads and axle spacing comprising of multiple locomotives and as heavy load as possible, close to the heaviest loads plying in thesection (subject to maximum of MBG-1987/ CC + 8 + 2) shall be arranged for testing in two rounds, preferably in the hottest/ coldest months. The two rounds of testing shall not be conducted less than 4 months apart. i 5. Instrumentation scheme: The rail-structure computations as per UIC 774-3 for the bridge instrumented shall be done and the stresses/ forces expected are worked out. In case, the work is outsourced, the agency selected shall cary out the analysis and submit details to railways. Based on calculations, the detailed instrumentation scheme shall be finalized, comprising of numberitype of sensors to be deployed along with their locations which still cover the following: Rails shall be instrumented at either approach of the spans being tested just beyond the spans so as to measure the longitudinal stresses continuously from the date of installation of the gauges (i.e. before the first round of testing) to the finish of the second round of testing. The measurement shall be correlated with the temperature readings. b. Temperature sensors shall each of the spans to be tested to take tempé*ature ridstireitionts oF rail jidge’ deck as defined in thé UIC-774-3R ~~ continuously from the date of installation of the gauges (Le. before the first round of testing) to the finish of the second round of testing. c. The longitudinal forces coming on the fixed bearing end (or both ends in case of neoprene bearings) on two typical spans of the bridge shall be measured. If the bridge is having fixed bearing on an abutment, that span shall be included as one of the spans to be instrumented. It is suggested that fixed bearings (or both end bearings in case of neoprene bearings) in span to be instrumented shall be replaced by free bearings and then load cell(s) shall be installed between the girder end and a suitably designed reaction frame to measure the longitudinal force coming on the span in either direction during the passage of test: train over the bridge and for at least 20 trains normal traffic passing over the bridge. Minor modifications may be required to be done to the girder for fixing the load a measuring the longitudinal forces coming on the fixed end of the bearing which may be examined and approved if found suitable. Rotation sensors shall be installed to measure rotation at the girder ends. d. e. Displacement transducers shall be provided to measure the horizontal deflection of the pier! abutment under longitudinal loads. f. Any other sensor required for satisfactory submission of the test report. 6. Preparatory works Just before start of testing: LWR/CWR shall be laid on the bridge if not already laid. LWR/CWR on the bridge and at least 250 m on either side shall be destressed, preferably with rail-tensor, or alternately, by other methods so that the Stress Free Temperature is established. Any destressing done within last six months will also be OK if no rail fractures or other unusual events a,have occurred in the LWRICWR in the stretch mentioned above since the date of destressing. Otherwise, fresh destressing may be done. Rails shall be instrumented and temperature sensors shall be installed on the rail and bridge deck and continuous date recording shall start. ‘The reaction frame already fabricated shall be fixed on the pier/ abutment. The fixed ‘end bearing (or both end bearings in case of neoprene bearings) shall be replaced by the new free bearings already fabricated and the girder and the reaction frame shall be Connected to transfer the longitudinal loads in either direction to the reaction frame, The newly provided free bearing shall continue to transfer all vertical loads. The connection of reaction frame shall be done such that the bending properties of the girder are not affected. Strain gauge shall be installed on the couplers of the test train, rotation sensors shall be installed at girder ends and load cells shall be installed between the free bearing newly introduced and the reaction frame. Test train shall be passed over weigh-bridge so as to determine the actual axle loads. e 7. Testing Work: In each round of testing, the measurements shall be taken for the following cases: a. Measurements under test train: Test train comprising of multiple locomotives and the heaviest loads permitted on the section shall be run multiple times on the bridge with the following operation conditions (Clarifications, if required, on these tests shall be taken from RDSO’s report no BS- 106) i. Test train static at three locations on span being tested so as to validate the end rotations and to determine the load call readings under ‘no longitudinal force" condition. Maximum tractive effort: The locomotive shall be stationary at the test span or near it and shall try to exert the maximum tractive effort for which brake binding may be introduced in a few wagons. The coupler forces in the locomotive shall be measured and th the location of the test train during the entire duration of test. For locos correlated Maximum braking force: Test train moving at maximum permitted speed on bridge/ section shall apply emergency brake just at the approach of the test spans such as to exert the maximum braking force. The coupler forces in the locomotive shall be measured and correlated with the location of the test train during the entire duration of test. Maximum speed test during which the test train shall be passed over spans at maximum permissible speed on the bridge/ section b. Measurements under normal traffic: iv. The measurements of stresses/ forces shall also be taken for the normal traffic plying on the bridge for minimum 20 trains. The data collected shall be correlated with the type of train passing on the bridge.8. Report on Testing: At the end of tests @ report shall be submitted. The report shall provide the following minimum information: ‘A summary report on temperature variation of the rails during the entire recording period a including trends and any unusual patterns. b. A summary report on temperature variation of the deck during the entire recording period including trends and any unusual ©. A summary report of the variation of the rail temperature vis-a-vis the temperature of deck by juxtaposing the readings from the different temperature sensors. d. Expected results of the additional stresses in rail and longitudinal forces as per Rail Bridge interaction studies as per UIC-774-3R for the actual temperature, vertical load and longitudinal loads actually coming on the bridge during the passage of test trains. fe. A summary report of actual variation of additional stresses in rail, rotation of spans and longitudinal forces during passage of test trains and their comparison with the theoretically worked out values as per UIC 774-3R. Analysis of the comparison including d conclusions to be drawn from the same [Link] possible reasons for the variation be brought out. A summary report of the peak values of additional stresses in rails on either end and longitudinal forces on the fixed bearing end during passage of normal traffic on the bridge. g. Report on the performance of bridge under rail-structure interaction as per UIC 774-3R, including comparison of results expected as per UIC code and actually seen and reasons for the variation. h. Any other conclusion based on the data collected. ft 9. Action after testing is over: The new free bearings/ reaction frames or other alterations in bridge provided for testing shall be replaced by original bearings and the bridge shall be restored to original ‘configuration. ‘10 Care snail B8 taka During the period in which the original bearings have been replaced by free bearings! reaction frames, the span shall be kept under-observation by open line as well as bridge organization.. The toe load of elastic fastenings shall not be Tess GOO KG ottrerwn Annexure-Il ‘Special maintenance instructions for LWR/CWR on Ballasted Deck Bridges: All the provisions mentioned in Manual of Instructions on Long Welded Rails-1996 and provisions of Indian Railways Permanent Way Manual-2004 related to maintenance of LWRICWR shall be followed strictly. The salient instructions are reiterated below, for ready reference along with certain other items where attentions are required for maintaining LWRICWR on ballasted deck bridges The bearings shall be inspected during the months of March and October each year and cleared of all foreign materials. Lubrication of the bearings shall be done once in two years. Bearing shall be monitored for unusual movements, loose bolts, other signs of distress etc. {Para [Link] (ll) (e) of LWR Manual). (On the bridge approaches, sleepers with arrangement for fixing guard rails should provided for provision of guard rails as per Para 275 of Indian Railway Permanent Way Manual. {Para 277 a (1) of IRPWM}. On the bridge approaches, for a length of about 100 meters, width of cess should be 90 cm clear of full ballast section to maintain ballast profile. For maintaining ballast section, Suitable ballast retaining arrangement should also be provided. {Para 277 b (2) of IRPWM}. be Full complement of track fittings on bridge and approaches upto 100 metres should be provided to maintain required track geometry and effort should be made to immediately recoup deficiency noticed, if any. {Para 277 a (2) of IRPWM}. . Alll welds on bridges and 100 m approaches on either side are joggle fish plated with clamps or two far end bolts. Creep of LWR shall be monitored on approaches, 20m from either abutment for which creep Posts shalll be provided. aT replaced — with ERCs having better toe load. The regular track maintenance in LWRICWR shall be confined to hours when rail temperature is between t, + 10°C and t,~ 30°C and shall be completed well before onset of ‘summer. {Para 6.2.1 (i) (a) of LWR Manual}. Mechanized cleaning of shoulder ballast shall be undertaken when prevailing rail temperatures are within the limits prescribed in para 6.2.1(i) of Manual of Instructions on Long Welded Rails together with the precautions mentioned therein. {Para 6.2.2 (iii) of LWR Manual}.10. During the period of deep screening, if there is any possibility of mirlirnum temperature falling 30°C below td temporary distressing temperature, cold weather patrol as per para 9.1.2 (i) of Manual of instructions on Long Wekied Rails should be introduced to detect! guard against rail fractures. In exceptional circumstances when more than 30 sleeper spaces have to be opened for any specific work, like through screening of ballast etc. during the period of the year when minimum daily rail temperature is not below td-30°C or maximum does not go beyond td+10°C, upto 100 sleeper spaces may be’ opened under the direct supervision of PWI. It should however, be ensured that rail to sleeper fastenings on the entire length of LWR are functioning satisfactorily and SEJs do not indicate any unusual behavior. {Para 6.2.3 (il) of LWR Manual}. Tamping in LWR/CWR with general lift not exceeding 50 mm in case of concrete sleeper including correction of alignment shall be carried out during the period when prevailing rail temperatures are as per para 6.2.1 (i) of Manual of Instructions on Long Welded Rails together with precautions laid down therein, {Para 6.2.2 (i) of LWR}, 1. 12, Lifting where needed, in-excess of 50 mm in case of concrete sleepers shall be carried out in stages with adequate time gap in between successive stages such that full consolidation of the previous stage as per Para 1.18 of Manual of instructions on Long Welded Rails Manual is achieved prior to taking up the subsequent lif. (Para 6.2.2 (i) of LWR Manua)}. 13, ‘When crow bars are used for slewing, care shall be taken to apply these in a manner so as to avoid lifting of track. In this connection, the instructions in Para224 (d) (ji) of Indian Railway Permanent Way Manual shall be followed {Para 6.2. 1b (iv) of LWR Manual}. 14, Duties and responsibilities at various levels shall be discharged meticulously as laid down under Para 9 of LWR Manual. 15,