BS 3288 : Part 2: 1990 yo 621.316.1 : 624.316.62/.65.002.7/.72(083.81) 008.378 British Standard Insulator and conductor fittings for overhead power lines Part 2. Specification for a range of fittings Accessoires pour les isolateurs et les conducteurs pour lignes aériennes Partie 2. Game standard — Spécifications Freileitungsarmaturen Teil 2. Normbereich NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW. Bes | British StandardsBS 3288 : Part 2: 1990 Foreword ‘This Part of BS 3288 has been prepared under the direction of the Power Electrical Engineering Standards Policy Committee and it supersedes BS 3288 : Part 2: 1977, which is withdrawn. In this revision an effort has been made to allow as much freedom as possible in the design while maintaining inter: changeability with existing designs and compatibility with other fittings. This has led to the omission of many non critical dimensions and, in some cases, one drawing with 2 table of dimensions now covers a series of fittings. A range of fittings with a mechanical rating of 300 kN fhas been introduced. The socket fittings in this range use the split pin security clip rather than the W security clip. In all fittings with a pin, washer and split pin, a bolt, nut and split pin has been given as an alterni ‘Such fittings are to be given a suffix A as part of their designation, e.g. shackle 18/29 is complete with pin, washer and split pin and shackle 15/294 is complete with bolt, nut and split pin. Other modifications include the addition of the 400 kN. sag adjuster assembly; the increase of the range of paralle! and single links; the provision of details of a suitable interconnecting shackle in the drawings of eye-links; the inclusion of square section tower-shackles; and the rationalization of the range of insulator pins to reflect current practice. Compliance with a British Standard does not of itself ‘confer immunity from legal obligations.Contents Page Foreword Inside front cover Committees responsible Back cover Specification 1 Scope 3 2 Performance and general requirements 3 3 Dimensions and tolerances 3 4 Insulator 3 5 Line post insulator studs 3 6 Insulator set fittings 4 7 Termination fittings and suspension clamps for conductors 5 Appendices A List of insulator set fittings 82 B List of insulator set fittings in order of ference number 83 Tables 1 Insulator pins 4 2 Dimensions of insulator pin with large steel head 7 3 Details of pilot insulator pin 7 4. Dimensions of ring gauge for head of insulator pin 8 5 Dimensions of bow shackle: reference numbers 16/28, 28/28, 42/28, 42/103, 67/103, 15/129 and 42/129 9 6 Dimensions of dee shackle: reference number 28/108 9 7 Dimensions of shackle: reference numbers 28/34, 42/34 and 67/34 " 8 Dimensions of ball-ended eye link: reference numbers 15/30, 28/30 and 42/30 4 9 Dimensions of bal clevs: reference numbers 15/83, 28/83 and 84/83 7 10 Dimensions of ball tongue: reference numbers 67/48 and 84/48, 20 11 Dimensions of socket cavi: reference numbers 15/84, 28/37, 42/37, 42/46, 42/104 and 84/37 21 12 Dimensions of socket clevis (with arcing horn attachment): reference numbers 16/31, 28/31 and 42/31 2 19 Dimensions of socket tongue (with arcing hora attachment): reference numbers 15/35, 28/36A, 28/368, 28/36C, 28/135, 42/36 and 42/3627 14 Dimensions of clevs tongue: reference numbers 42/284, 42/288 and 42/28C 30 18 Dimensions of clevis tongue: reference numbers 42/398, 42/398, 42/54A, 42/548 ond 42/139 31 16 Dimensions of twisted clevis-clovis: reference numbers 15/23, 28/23, 67/23 and 84/23 35 17 Dimensions of adaptor: reference numbers 18/278, 15/27C, 15/270, 28/278, 28/27C and 28/87 38 18 Dimensions of clevs ends for clamps: reference numbers 91A, 918, 91C, 91D, 91E and91 38 18 Dimensions of tongue ends for clamps: reference numbers 82A, 92B, 92C, 93A and 938 39 a 22 26 27 29 30 3a 32 33 34 35 BS 3288: Part 2: 1990 Dimensions of terminating strap: reference ‘numbers 4/89A and 4/898 imensions of single link: 15/86, 28/86, 42/86 and Dimensions of parallel links: reference numbers 28/88A, 42/88A, 42/888, 42/88C, 67/88 and 84/88 Dimensions of parallel conversion links: ‘reference numbers 28/89, 42/89 and 67/89 Dimensions of cranked links: reference numbers 15/87, 28/87, 42/87 and 67/87 Dimensions of cranked links: reference numbers 42/102 and 84/102 Dimensions of landing plate: reference numbers 15/21, 28/21 and 42/21 Dimensions of yoke plate: reference numbers 28/22, 42/22 and 42/124 Dimensions of suspension clamp body and closed type strap for line and earth conductors: keeper type and closed type strap Dimensions of suspension clamp body and open ‘ype strap for line and earth conductors: keeper type corona free and open type strap Dimensions of suspension clamp body and straight type strap for line and earth conductors: two-part corona free and straight type strap Dimensions of sag adjuster/shackle pins H, Larid M complete with washers and split pins Dimensions of sag adjuster pins/bolts P,Q, RandS Dimensions of spacer for sag adjuster pins/bolts RandS Dimensions of clevis pin and split pin Dimensions of bolt and split pin Figures Dimensions of small stee! insulator pin head Dimensions of large steel insulator pin head Insulator pin with small steel head ‘number 23, Insulator pin with large steel head Pilot insulator pin Ring gauge for head of insulator pin Shackle: reference numbers 15/29, 28/29, 42/29, 42/103, 67/103, 15/129, 42/129 28/108 ‘Shackle: reference number 16/33. Shackle: reference numbers 28/34, 42/34 and 67/34 nce number 4/88 : reference number 18/32 Ball-ended hook: reference number 18/81 Ball-ended eye link: reference numbers 15/30, 28/30 and 42/30 Ball-ended eye link: reference number 18/82 Ball-ended eve link (twisted): reference number 42/44 Ball clevis: reference numbers 16/83, 26/83 and 84/83 Ball clevis: reference number 16/25 Page a 43 45 & n 2 essa 1" 2 13 13BS 3288 : Part 2: 1990 Page 18 Ball clevis: reference number 84/25 9 19 Ball tongue: reference numbers 67/48 and 84/48 20 20 Socket clevis: reference numbers 15/84, 28/37, 42/37, 42/46, 42/104 and 84/37 2 21 Socket clevis (with arcing horn attachment): reference numbers 15/31, 28/31 and 42/31 22 22 Socket clevis (with arcing horn attachment): reference number 42/45 23 23 Socket clevis (with arcing horn attachment): reference number 67/31 24 24 Socket clevis (with arcing horn attachment): reference number 84/31 6 25 Twisted socket cl arcing horn attach- ment): reference number 28/1314 26 26 Socket tongue (with arcing horn attachment reference numbers 15/35, 28/36A, 28/368, 28/36C, 28/136, 42/35 and 42/36 27 27 Socket tongue (with arcing horn attachment): reference number 42/51 28 28 Socket tongue: reference number 15/85 28 29 Clevis-tongue : reference number 28/28 29 30 Clevis-tongue : reference numbers 42/28A, 42/28B and 42/28C 30 31 Clevis tongue: reference numbers 42/39A, 42/39B, 42/54A, 42/548 and 42/139 an 32 Earthwire adaptor: reference number 28/50A 32, 33 Earthwire adaptor: reference number 28/40A_ 33 £ ‘Twisted clevis-clevis: reference numbers 15/23, 28/23, 67/23 and 84/23, 36 36 Twisted clevis-clevis: reference number 28/24 36 37 Twisted clevis-clevis: reference number 42/23 37 38 Adaptor: reference numbers 16/278, 15/27C, 15/270, 28/278, 28/27C and 28/47 38 38 39 39 40 39 Clevis ends for clamps: reference numbers 914, 918, 91C, 91D, 91 and 91 40 Tongue ends for clamps: reference numbers 982A, 928, 92C, 93A and 938 41 Terminating strap: reference numbers 4/898 and 4/898 42 Strap section and termin: 4/90 43 Single link: reference numbers 15/86, 28/86, ference number 42/86 and 67/86 a 44 Single conversion link: reference number 42/15 42 45 Parallel links: reference numbers 28/88A, 42/88A, 42/888, 42/88C, 67/88 and 84/88 43 46 Parallel conversion links: reference numbers 28/89, 42/89 and 67/89 a 47 Cranked links: reference numbers 15/87, 28/87, 42/87 and 67/87 45, 48 Cranked links: reference numbers 42/102 and. 84/102 46 49 Cranked links: reference number 28/1864 a7 50 Landing plate: reference numbers 15/21, 28/21 and 42/21 48 76 7 78 79 80 82 ‘Sag adjuster plate: reference number 15/101 reference number 28/100 reference number 42/100 reference number 42/101 reference number 67/100 reference number 67/101 reference number 84/100 reference number 84/101 reference number 15/22 reference number 42/52 reference number 56/122 reference number 67/40 reference numbers 28/22, 42/22 reference number 28/43 reference number 84/40 reference number 84/41 reference number 84/42 reference number 42/42 reference number 84/52 reference number 84/53 reference number 84/22 Gruciform yoke plate: reference number 84/38 ‘Yoke plate: reference number 84/43 ‘Suspension clamp body and closed type strap for line and earth conductors: keeper type and. closed type strap ‘Suspension clamp body and open type strap for line and earth conductors : keeper type ‘corona free and open type strap ‘Suspension clamp body and straight type strap for line and earth conductors: two-part corona free land straight type strap ‘Sag adjuster assembly with 190 kN insulator units: single conductor ‘Sag adjuster assembly with 190 KN insulator units: vertical pair of conductors ‘Sag adjuster assembly with single 400 kN ingulator units: vertical pair of conductors (two sag adjusters) Sag adjuster assembiy with 300 kN insulator units: single conductor ‘Sag adjuster assembly with single 400 kN insulator units ‘Sag adjuster assembly with single 400 kN insulator units: vertical pair of conductors (single sag adjusters) Sag adjuster/shackle pins H, L and M complete with washers and split pins Sag adjuster/link pin J complete with washer and split pin Sag adjuster pins/bolts P,Q, R and S complete with washer and split pin Spacer for sag adjuster pins/bolts Rand S ‘Typieal arcing horn flag levis pin and split pin Bolt and split pin Page n n B ” 4 78 76 ” 78 1” 19 80 81Specification 1 Scope This Part of BS 3288 specifies requirements for a range of insulator and conductor fittings for overhead power lines. ‘The dimensions are given in figures 1 to 89 and tables 1 1035. NOTE 1. Typica errngements of sag adjuter assemblies are shown in figures 77 1082. [NOTE 2. The titles of the publications referred to in this standard ‘are listed on the inside back cover 2 Performance and general requirements The fittings shall comply with the appropriate requi ments of BS 3288 : Part 1 3 Dimensions and tolerances The following tolerances shall apply to the dimensions given in figures 1 to 89 and tables 1 to 36, except for dimensions given in parentheses or indicated by the suffix ‘max.’ or ‘min.’ or for dimensions for gauged parts, gauges fr screw threads (see clauses 4 to 6): dimensions up to and including 35 mm: + 0.7 rm dimensions greater than 35 mm: + 2%, NOTE. Dimensions shown in parentheses ae given for guidance only. All dimensions except diameters of bolts and pins, thick- ‘esses of rolled plates and widths and thicknesses rolled rectangular material shall apply after galvanizing. For the exceptions stated, the dimensions shall apply before galvanizing. All holes shall be parallel sided. 4 Insulator pins 4.1 Reference numbers ‘The reference number for each type of insulator pin ‘and each type of head shall be as given in table 1. 4.2 Dimensions ‘The dimensions of every insulator pin shall be in accordance with the appropriate figure, as given in table 1. 4.3 Gauges The accuracy of the dimensions of the head shall be checked after galvanizing by means of the gauge referred 10 in table 1 and shown in figure 6. “Iso Internationa! Organization for Standardization. BS 3288 : Part2: 1990 4.4 Shanks ‘The thread on the shank, before galvanizing, shall be ISO ‘matric coarse pitch series ‘free’ class (B g) complying with BS 3643 : Part 2. The effective thread on the shank shall bbe not less than 45 mm long for the 60 mm shank and not, less than 75 mm long for the 130 mm shank, NOTE. For the purposes ofthis subelause, “effective thread’ means ‘that the thread, ster galvanizing, takes @ nut forthe distance rated. 4.5 Nuts ‘The external dimensions of the nut, before galvanizing, shall comply with BS 4190 and it shall have a thread, ‘cut after galvanizing, complying with BS 3643 : Part 2, but sufficiently oversize to accommodate the threaded part of the galvanized shank, as specified in 4.4. The increase in diameter to comply with this requirement shall not however exceed 0.4 mm. The threads of nuts shall be oiled. 4.6 Failing loads The minimum failing load of the pin shall be 0.7 KN (pilot, pins only), 5 kN or 10 KN, as given in table 1. 5 Line post insulator studs 5.1 Studs ‘The shank length shall be measured below the seating surface of the metal base. The thread on the stud, before galvanizing, shall be ISO metric coarse pitch series ‘free’ Class (8 g) complying with BS 3643 : Part 2. The effective thread on the stud shall be not less than 45 mm long for the 50 mm shank and not less than 75 mm long for the 130 mm shank. NOTE 1. The preferred diameter of line port inulator studs is :22:mm, with alternative shank lengths of 80 mm and 130 mn, NOTE 2. For the purpoter of this subs fective thread ‘means thatthe thread, after galvanizing, cakes» nut for the distance fated. NOTE 3. When tine post intulator studs are ordered separstely, ‘care should be takan to ensure thatthe upper part ofthe stud is suitable forthe insulator 5.2 Nuts ‘The external dimensions of nuts before galvanizing shall comply with BS 4190 and they shall have threads, cut after galvanizing, complying with BS 3643 : Part 2 but suffi ciently oversize to accommodate the threaded part of the, ‘galvanized pin shank as specified in 4.4. The increase in iameter to meet this requirement shall not however exceed 0.4 mm, The threads of nuts shall be oiled,BS 3288 : Part 2:1990 | Table 1. Insulator pins Hed | ‘Type Sta tangth | Shank Minimum —|Pin [Pin o {aling ond | reterence tours ‘Description | Reference | Gaupee in Diameter [Length | withstanderd | number” number umber imeunting pe FRaterence | Figure trrangemant owe | number” | number (ioe BS 3268 number Par) mm mm mm aN A tine {65 8 s0.or120 | 10 ab smarsea |35.0, fase |e co ror [500 20 soor80 | 07 of 165 8 woort20 | 6 28 10 2 Lune [230 2 [soort90 | 5 72 0 Ean [306 2 woorta0 | 5 sof 16 1 jak Lageee [28.4 [rer |e 2 igure [400 | 20 ‘50 or 160 oe 6 Ps Ey 2 0° 180 so NOTE 1. Underlined characters represent prefer British practice. NOTE 2, The stalk and shank lengths of pilot pins are rm sured above and below the bottom face of the top nut (se figure 5) NOTE 3. A washer is required if an ineulator pin with » 60 mm shank isto be used with a crossarm 7 mm or ls in thickness, 6 Insulator set fittings NOTE. The reference number asigned to each type of insulator st firing i ivan in appendix A and, for convenience, alist of {iting in order of reference number is given in appendix . 6.1 Mart ing 6.1.1 General. All insulator set fittings shall be marked betore galvanizing in accordance with 6,1.2 to 6.1.4, 6.1.2 Castings. Castings shall be marked with the follow: ing information: (a) the appropriate reference number in raised characters at least 6 mm in height; {b) the manufacturer's nam mark; {e) the cast code, including year. identification or trade 6.1.3 Forgings. Forgings shall be marked with the follow: ing information: (a) the appropriate reference number in raised characters between 4 mm and 6 mm in height; (b) the manufacturer's name, identification or trade mark. 6.1.4 Links and plates. Links and plates shall be marked with the following information: (a) the appropriate reference number in characters at least 6 mm in height; (b) the manufacturer's name, identification or trade mark.6.2 Dimensions ‘The dimensions of every insulator set fitting shall be as iven in the appropriate table and figure. 6.3 Ball and socket couplings Where fittings are provided with ball and socket couplings, the dimensions of the ball and socket shall be as given in BS 3288 : Part 3 for the appropriate size of coupling. ‘The dimensions of ball or socket shall be checked by means of the gauges described in BS 3288 : Part 3 6.4 Failing loads ‘The minimum failing load of the fitting shall be as given in figures 7 to 76 and/or the appropriate tables. 6.5 Bolts and nuts Where bolts and nuts are supplied as parts of clevis-ended fittings instead of pins (as provided for in the relevant figures), the bolts shall be ISO metric hexagon bolts complying with BS 4190 before galvanizing. {n addition, bolts shall have screwed length and cross drilling dimensions 2s given in figure 89 and table 35, except arcing horn bolts which are not covered by figure 89. The thread lengths of arcing horn bolts shall comply with 7.1.2 of BS 4190 : 1967 and shall be fitted with a plain wather and two full ruts. ‘The external dimensions of the nuts, before galvanizing, shall comply with BS 4190 and they shall have threads, cut after galvanizing, complying with BS 3643 : Part 2 but sufficiently oversize to accommodate the galvanized bolts, The increase in diameter to meet this requirement shall not however exceed 0.4 mm. The threads of nuts shall be oiled. BS 3288: Part 2:1990 6.6 Washers When washers are supplied they shall have dimensions before galvanizing as given in table 3 of BS 4320 : 1968. 6.7 Split pins Split pins shall comply with BS 1574 and shall be of austenitic stainless steel capable of complying with the requirements relating to the intercrystalline corrosion ‘test of BS 970 : Part 4. In addition, split pin sizes shall be as given in figures 88 (and table 34) and 89 (and table 35), 6.8 Security clips Socket type fittings shall be supplied complete with security clips complying with BS 3288 : Part 4. 7 Termination fittings and suspension clamps for conductors Termination fittings and suspension clamps are not completely standardized dimensionally but if a clamp includes a clevis or tongue, this part shall be in accord- ance with figure 39 or figure 40. If a clamp is provided with a ball or socket coupling, the ball or socket shall have dimensions complying with BS 3288 : Part 3 for the appropriate size of coupling. The dimensions of the bal! (or socket shall be checked by means of the gauges described in BS 3288 : Part 3. NOTE 1. The clvis, tongue, ball or socket may be Integral with the clamp or may be on 8 fitting supplied as part of the clamp. ‘Typical suspension clamps are shown in figures 74 t0 76 NOTE 2. Minimum foiling londs are not stendrdized for termination fittings,BS 3288 : Part 2:1990 General notes on figures and tab NOTE 1, All dimensions are given in milimetres except where stated otherwise. NOTE 2. Dimensions given in parentheses are for guidance oni. [All other dimensions are subject tothe tolerances given in clause 3. NOTE 2. Where the geometric form of the contour of @ component ie not fully specified By, or capable of being deduced from, the dimensions given, twill suffice forthe form to approximate to that shown inthe Figure NOTE 4, First on NOTE 5. Specing dimensions of socket-anded ftings should be ‘checked with a ballin the socket. The GO gauge bal tailed in projection is uted throughout figure 810 of BS 2288 : Part 3 should be ured for this purpose NOTE 6. For clarity, the cotter pin hos been omitted from one View ofeach clevi-ended iting. NOTE 7. Where fittings re avilable with sither a bolt or cotter pin, the cotter pin has been shown. Suffix‘ should be added to the reference number if bolts are required. In the past, some fitting \with minor differences were allocated a suffix A, B or C. When one of these fitinge ist be supplied with a bol, the sufix becomes and regitrtion ledges Ingended that the ledges should be, angles to the Fixing face, NOTE 9. Details of pins, bolts and split pins ae given in figures 88 ond 8. [NOTE 10, Galland socket couplings ae designated in 85 3288, Par 3, which gives the detailed cimensions. NOTE 11. The dimensions of security clip ore given in 8S 3288, Port 4, which also includes text requirements 2780 416 30.95 Al dimensions are in millimetre. NOTE. Insulator pin heads are subject to gauging ( Figure 2. Dimensions of large stea! insulator (to0 table 1, reference number 16) 91830, 310 bib 155) R125: 273.35 {All dimensions ore in millimetre. NOTE. Insulator pin heads ere subject to gouging (see 4.3). Figure 1. Dimensions of small steel insulator pin head (see table 1, reference number 15) Small steel head 165 43 min: O31 min Rt 50 screwed 45 oF 130 screwed 75 [All dimensions are in mitimetres. NOTE. A washer is required if an insulator pin with 2 60 mm shank isto be ured with @crossarm 7 mm or less in thickness, Figure 3. Insulator pin with small steel head : reference ‘umber 23 (minimum failing load 10 kN)Large steel head insulator pin with » 60 mm stank is fo be used with @crossrm 7 mm oF les in thickness, X50 of 150 Figure 4, Insulator pin with large steel head screwed full length M20 Toble 2. Dimensions of insulator pin with — large steel head Dimension Minimum tailing lose totum fing Figure 5, Pilot insulator pin 5KN w0KN Reference number of pin 26 [m2 [20 [27 [2 [31 A ies | 230 | 30s | Tes | 250 | S08 8 min, a7 [a fas [as [so [os = Table 3. Details of pilot insulator pin ee 2 [za [28 [ze [2s [27 18 numberof pin | Type o Reference number @0 min, 20 [ze [ar [ar [ar [ao Reference number of pin | Type of heed | Reteren ath (ne figures 1 and 2) of we [2 [22 [w fz [2 us (190 Figures 1 and 2) les ele 1s “400mm | 600 mm 7 malt stot | 1 (RG) w [is fs fis [is fie “8 s 6 x 50 or] 60 0 50 or| 50 0r| 50 or] 50 oF “ 6 Larne steer | 16 130 |130 ] 130. [130 | 130. | 130 Dimension X to be 60 mm screwed 45 mm, or 130 mm screwed 78 mmBS 3288 : Part 2: 1990 ini Maximum ! A [Extent of head Figure 6, Ring gauge for head of insulator pin Table 4. Dimensions of ring gouge for heed of Insulator pin ras Tame [emes]a lo pe |e |r Sites [rere = roa ee ee ee Ten | twve [te fare farsnfooas|i eo [ae [eas NOTE 1. Tolerance on specified dimensions 0.02 mm. NOTE 2. The dimension Cis the base of the conic frustrum which determines the taper of the gauge.BS 3288 :Pant2:1990 Pin with washer and split pin or, hex. bolt with nut and split pin o | 7 Dp | Figure 7. Shackle: reference numbers 15/29, 26/29, 42/29, 42/103, 67/103, 16/129, 42/129 and 28/108 ees Table 5. Dimensions of bow shackle: reference numbers 15/29, 28/29, 42/29, 42/103, 67/103, 15/129 and 42/129 mioimum [a [oc fo leele [a los Bolt | tailing oat Lonath | Di kN ‘mm | em | mm | mmm | rom | mom | mm | anm mm mm 15129 70 70} 19 | a5 | 18 | 95] 16 | 16 | 16 co | mis 70 res | 125 ye|21 | 4 | 22 | 13°] 19 | 19 | 20 6s | wo a5 42720 | 190 e327 | st | 24 | 22 | a | 22 | 2 35 | waz 1s @203_ | 190 es [28 [st | 27 | 22 [a7 | 22 | (sonora) (ase note 2) e703" | 300 90|27 | 60 | 29 | 25 | 20 | 25 | 27 105 | war 120 wsnze | 70 v0 22 [as [ie | 19 | 19 | 19 | 16 vo | we 90 a2n2a | 190 102 | 28 | 87 | 32 | 22 | 17 | 22 | 30 roo | a0 120 [NOTE 1. Pins, washers and split pin (oF Bolts, nuts and split pins) are Included, except for reference number 42/103. NOTE 2, Reference number 42/103 was thackle Z in the pravious edition of this Part of BS 2288. NOTE 3. Reference number 42/103 is used in s09 adjuster assemblies (see figures 77 and 78) Table 6, Dimensions of de number 28/108 minimum [a lo ]o [ee]e [a Jos | ein Bott failing enath | Diameter | Length kN mm | eam | mom | mm | enm | mm | mom | mm mm am zeos | 125 aa | ae | as | 26 | 20 | 19 | 20 | 22 105 | wan 125(235) 19 16 x 65 pin with washer and split pin or M1675 hex. bolt with nut and split pin cy “tow All dimensions are in milimetres. Nore. i, spit pin and washer (or bolt, nut and slit pin) are included, reference number 15/33 (minimum failing load 70 kN) 10BS 3288: Part 2:1990 BSW bolt and nut to BS 916, 30mm hin thea eagtn inch inch inch > 1%¢inch split pin in ‘inch hole orn | oss max. Bol for 28/34 shackle (90 note 1) NOTE 1. Sheckle 28/34 is supplied with # BSW bolt. NOTE 2. Bolt, nut end split pin ere included. Figure 9. Shackle: reference numbers 28/34, 42/34 and 67/34 Hex. bolt with nut ble 7. Dimensions of shackle: reference numbers 26/24, 42/34 and 67/34 ference oH | Boteaiameter — | Bott length umber KN _ — zase | 126 21 | See inset drawing | See inset drawing 42st | 190 27 | wa 125 67 | 300 2 | 27 130BS 3288: Part2:1990 16 ball ‘and shank igure 10. Ball-ended hook: reference number 4/88 (minimum failing load 20 KN) 12BS 3288: Part2:1990 = — - ee 5) (so) Ria 28 9 $ 9 16 ball and shank ference number 15/32 (cninimum failing load 70 kN) lus) 16 ball and shank All dimensions are in millimetees, Figure 12. Ball-ended hook: reference number 15/81 (minimum failing load 70 kN) 13BS 3288 : Part 2:1990 Max. dimension to Prevent fouling H tw) w RE All dimensions ilietren, igure 13, Ball-ended oye link: reference numbers 15/30, 28/30 and 42/30 ‘Table 8. Dimensions of ball-onded eye lin : reference numbers 15/30, 28/30 and 42/30 Reference | Minimum Jos [a [@ [ce |o |e |F |e |W |v | Reterencenumber number | failing | size of shackle used load max, with aye tink kN vm | ew | ome | mm [mm | mm| mm | mmm | mm | mm 18/30 70 se [ve |s7 jie fas [a1] |i | 20 | 34 | 15720 zeys0 | 128 2 [165 |67 jis | 7 | 18 | 85 | 20 | 23 | 37 | 28/20 a7is0 | 3190 ze [168 | 75 | 205 }6s | 16 | 13 | 25 | 25 | 38 | 42/20 14BS 3288 : Part2:1990 | , Max. dimension to | prevent fouling | 20 ; | 4s 102] _ | 16 bait and shank | | All dimensions aren eilimetre | | NOTE. For use with shackle reference number 18729. Figure 14. Ball-onded aye link: reference number 15/82 {eninimum failing load 70 KN) 15BS 3288 : Part2:1990 Max.dimension to Brevent. fouling 205 (38) 24 ball and shank All imensions are in milimetres. NOTE. For use with shsckle reference number 42/28. Figure 15. Ball-ended eye link (twisted): reference number 42/44 (minimum failing load 190 kN) 16BS 3288 : Part2:1990 rir’ “Hel . Pin with washer and split pin or hex. bolt 7 J with nut and split pin Fin clearance cq NOTE. Pio split pin and washer (or bolt, nut and split pin) are included. Figure 16. Ball clev reference numbers 15/83, 28/83 and 84/83 ‘Table 9. Dimensions of ball clovis: reference numbers 16/83, 28/83 and 84/83 Retecance | Minimum | ost | a |B c jo joe |r |rm Bott number | failing | size -— toed max min. | Diameter | Length Length kN om [mm [mm [mm [mm [mm lam | mm om 15/83 70 16 a |e |ies jas |i |a2 lis so fms | 65 zees | 128 20 os ju jas |a2 ja jaz |20 so |wz0 | 80 eas | 400 ee jz [te [2s [4s | 32 jer 30 as |ws0 | 110 17BS 3288 : Part2: 1990 16x50 pin with washer and split pin oF M16x6Shex. bolt with nut and split pin an 2 \ R32 min, YL] cearance i is 7 Ri6mex Tien, [0 a aoe “Ty s7 | 1c 16 ball and shank {ll dimensions are in mitinetes NOTE. Pin, split pin and washer (or bolt, nut and spit pin) Included. Figure 17. Ball clevis: reference number 15/25 (minimum failing load 70 kN) 1830x85 pinwith washer and split pin or M30x110 hex bolt yg 2) 12 6 with nut and split pin = p32 AIA RSI min Ct - clearance Ru \ 288 ball 38 38 and shank {Al dimensions ore in millimetres. NOTE. Pin, split pin and washer (or bolt, nut and split pin) are included. Figure 18. Ball clevis: reference number 84/25 19BS 3288: Part2: 1990 U6 max, dimensions Figure 19. Ball tong reference numbers 67/48 and 84/48 Ri.emax rable 10. Dimensions of ball tongue: reference numbers 67/48 and 84/48 Reference | Minimum | Ban | a ce |eo umber | failing | size load kn mm [mm [mm | mm 61/8 | 300 2 | tss | es | 25 | 29 saias | 400 zee [iso jes | 25 | a2 20BS 3288: Part 2:1990 Slot for W security clip RGmin clearance (Ro) NOTE, Security clip, pin, spit pin and wes Pin with wesher and split pin or hex. bolt with nut and split pin (or bolt, nut and spt pin) are included, Figure 20. Socket clevis: reference numbers 15/84, 28/37, 42/37, 42/46, 42/104 and 84/37 1¢0 numbers 15/84, 28/37, 42/37, 42/46, 42/104 and 84/37 sou} A |e |c |o lee |r ja | Pin Bolt " Diameter | Length | Diameter | Length KN mm | mm mm | mm | mm mm mm mm 70 23 jw |e 16 so | M16 65 125 20 76 | ay 32 | 2 | 36 20 ss | M20 70 190 2 76 | 41 we | 24 | 19 2 70 | maz 90 190 24 aan | = ap | 2a | a3 2 75 | Maz 95 aziioa | 190 24 105 ae | 32 | 22 30 100 | M30 | 120 e437 400 zee | 105 | — 46 | a2 | 22 30 roo |ms0 | 3200 | 24BS 3288 : Part 2: 1990 Slot for W security ctip \ f | ' ' | : &| Tt mena C/ Loe - 7 70 max. to accommodate arcing horn F_ (Ro) Pin with washer | and split pin or hex. bolt with nut and split pin {Al dimensions are in millimetres. NOTE. Security cl er (or bolt, nut and spit pin} are included, Figure 21, Socket clevis (with arcing horn attachment): reference numbers 15/31, 28/31 and 42/31 in, spit pin and we ‘Table 12. Dimensions of socket clevis (with arcing horn attachment) : reference numbers 16/31, 28/31 and 42/31 Reference | Minimum | Socket | 4 | & A od jee |r Pin number” | falling | size max. load Diameter | Length Length kN emm | emm [mm [mm | mm fmm [mm | mm mm 15/31 70 ves |10 |e [ws |2s |e 8 |ie so jus | 6s. zest | 125 2 |i | jas |a2 | 2 ss |20 ss |mz0 | 75 azist_— | 190 2 | 19 | 760 | 25 38) | 28) fas | 22 7 | wz | a8. 22BS 3288 :Part2:1990 Slot for W security clip 70 max.to accommodate arcing horn 18 22, - ‘S t= 22x70 pin with washer and split pin or M22 x90 hex. bolt with nut and split , ol al Le * All dimensions are in millimetres. NOTE. Security clip, pin, split pin end wesher (or bolt, nut and split pin) are included. Figure 22. Socket clevis (with arcing horn attachment): reference umber 42/45 (minimum failing load 190 kN) 23BS 3288 :Part2:1990 24 socket 5 fe for split pin security ip 6 18 R16 max Tomax. to accommodate arcing horn : O29 L-4 5 ~Y ey ; u LJ} LU R35) 221235 pin “with washer and split pin ormar [oa]a |s |r load numbe max, | min. oN mm om | am com [oom | mm [oem [i sare | 70 76 2 |t6 tare | Je 78 2 |i sia__{to |e {20 [a2 [as wae | 50 | wo zs [is 28/278 126 76 32 | 20 se 22 [22 | 32 |s2_|87 genre | 128 8 33 |20 2erar | 128 108 38 | 20 ste 25|22 |o2 |x |s7 oo [as [a | |e [oo sie [as [a [as [ase [os or a1 [x [oo [ae [es 38BS 3288 : Part 2: 1990 P, 2a ZN Rex. | aa S min Sain igure 40, Tongue ends for clamps: reference numbers 92A, 928, 92C, 893A and 938 (see clause 7) 2% 25 “oy Q . T ‘en wt 0 15 chamfer 1 T i tf {Alt dimensions are fn linet Figure 41. Terminating strap: reference numbers 4/894 and 4/898 {minimum failing toad 20 kN) Table 19, Dimensions of tongue ends for ‘Table 20, Dimensions of terminating clamps: reference numbers 92A, 928, strap: reference numbers 4/894, 82C, 934 and 938 and 4/898 e |eafa |s [mn Reference |x max. [min number 82a 16 [1 24 |25 Jas 41894 0 ‘re08 138 928 19 [2 [25 |ss [so ae 22 [a [oe [38 [os 938 2xe| 18 | 2¢ [25 [50 58 2xe| 2 |25 32 |s0 39BS 3288: Part 2: 1990 R30 10} holes 222 (2outer holes to be chamfered on - both sides of L- straph 4s| 65| R30 Al dimensions are in millimetres. Figure 42. Strap section and terminal: reference number 4/90 (minimum failing load 20 KN) 40BS 3288 :Part2: = 20 St Table 21. Dimensions of single link: reference numbers 16/86, 28/86, 42/86 and 67/86 Reference | Minimum | 4 8 c oo |e re |e number | failing max. load kn om | mm fmm fmm | mm | mm 15/86 70 . aw | |r |2 |ss fro reyes | 128 : so [20 [22 |20 |e iz azes | 100 : 6 [22 |27 |x |s is 67798 | 300 : so {25 [2 [as |e | 20 *As required. Preferred values are 160 mm and 400 mm. NOTE. Reference number 42/88 may be manufactured from strip 25 mm thick with the ends reduced %0 22 mm. at 1ey4 ef Alternative end 1990Rel Radmax ‘Aernative ond 38, hg 1 7 F Sao ome TE ‘Alternative end Figure 44. Single conversion link: reference number 42/115 (minimum failing load 190 kN) 42BS 3288 : Part 2:1990 i + | | k is i | Pin with washer and split pin or hex. bolt with nut and split pin ns of parallel links: reference numbers 28/88A, 42/B8A, 42/88B, 42/B8C, 67/88 and 84/88 Raterence [Minimum | A [@ [co [oo le [F [a |w | Pimi2y Bots (2) umber | failing max load Diameter | Length | Diameter | Length kN om ‘am [mm [mmm [mm | eoem | eon | mem | mm om 125 180 a |22|30 |22 |as | 12 | 20 ss | nao 70 190 185 12 |27 | 38 |27 Jaa | 18 | 20 75 | M24 98 190 127 x2 | 77 | 38 |27 [a5 | as | 20 75 | M24 95 190 150 x2 |27 |38 27 [aa | a6 | 24 78 | ae 95, 300 200 42 | 29 | 45 |26 [eo | 20 | 27 7s | a7 95, saa | 400, 152 12 | 32 | 85 |29 [60 | 25 | 30 ao Mao | 100 43BS 3288 : Part2: 1990 \ _|—t | a Le tvernatie er | nes max 30x80 long pin with washer and split pin or M30x 100 Long hex. bolt with nut and split pin All dimensions are in millimesres. Figure 46. Parallel conver Tenge 150 NOTE. Pins, washers ond spit pine (or bolts, nuts nd split pin) ore included TT He n links: reference numbers 28/89, 42/89 and 67/89 Tf cl Le in with washer and split pin or hex. bolt with nut and split pin R60 max. 44 Table 23. Dimensions of parallel conversion links: reference numbers 28/89, 42/89 and 67/89, Reference | Minimum |oa |e e Pin Bolt number | tailing food Diameter | Congth | Diameter | Length zeeo | 125 aso | 190 e7ea | 300BS 3288 : Part 2: 1990 a ae i 4 cS} et | iC Le RF max, "2 ” es i — ° oo : | lr | yt 1m) Ic J nin. | Pin with washer and split pin NOTE. Pin, washer and split pin (or bolt, nut and slit pin) ar included, 47. Cranked s: reference numbers 15/87, 28/87, 42/87 and 67/87 for hex. bolt with nut and split pin Table 24. Dimensions of cranked links: reference numbers 15/87, 28/87, 42/87 and 67/87 Reterance 4 |e je jeje je fo [# |r [rin Bott number max. nin, Diameter Diameter w rm | mem | men [mem om om | mm om 15/87 70 + fa |e | [2 10 | 185| 38 | 16 so jms jes. 2esr | 125 + es |e |22 |29 12 | 21'5| 38 |20 ss |wz0 —|70, 4767 | 190 + |70 | 10 27 |33 15 | 26 | 45 [24 7 =| m2e | 90. 6787 | 200 + Jao [12 |20 [as 20 | 26 | 65 |27 7 |wa7 jo, *As required but 36 150 mim and 200 men, 45BS 3288 : Part 2: 1990 - ff iC nin, Kin. Pin with washer and split pin or hex. bolt with nut and split pin NOTE. Pin, washer and spit pin (or bolt, nut and split pin) are included. Figure 48. Cranked links: reference numbers 42/102 and 84/102 Table 25, Dimensions of cranked links Reterence [Minimum | |e |e loole |e [ela ly |x [rin ‘umber max. in, | min. ad Diameter | Length Length 42102 | 190 ss2| 65 |12 |27] 38 | 28 | 18 | 26| 38 |s0 | 24 78 | 2a 95 Bayoz | 400 200} 100 | 12 |32 | 65 | 60 |25 |27| 60 |60 |20 20 | wao | 100 NOTE. Link 42/102 was previously known es link F end link 84/102 war previously known as link G 46BS 3288: Part2:1990 120%70 long bolt with nut and split pin All dimonsions are in millimetres. NOTE. Bolt, nut and split pin are included. Figure 49. Cranked links: reference number 28/186A (minimum failing load 125 kN) 47BS 3288 : Part2:1990 i im Tit? { T Figure 50. Landi plate : reference numbers 15/21, 28/21 and 42/21 Table 26. Dimensions of landing plate : reference numbers 15/21, 28/21 and 42/21 Reterance | Minimum | A e |ec joo je umber | failing | max. load kN mm [mm [mm [mm | mm 1521 70 23 | lw |e |is aor | 126 az [es [22 jas | 20 azz | 190 a7 [os [ze fae | oe 48BS 3288 : Part2:1990 Tholes 218 R25, 70 R25 All dimensions are in millimetres. Fi Ras 51. Sag adjuster plata: reference number 15/101 (minimum failing load 70 KN) 49BS 3288: Part2:1990 T holes 22 RZ 70 R27 oad 125 KN) 50BS 3288 : Part2:1990 Figure 53. Sag adjuster plate: reference number 42/100 {minimum failing load 190 KN for a pair of plates)BS 3288 : Part 2: 1990 Bholes 227 a {All dimensions are in millimetres. NOTE. See figures 77 t0 79 and 82 for sag adjuster assemblies. Figure 54. Sag adjuster plate: reference number 42/101 (minimum failing load 190 KN) 52BS 3288 : Part 2: 1990 65, R4o Ruo 65, UO. ' 205| 65 \ t \ene | 25 R40 — o\ | 6s pio \ \ R00 — ‘s Ruo Thotes #29 Rho 128 NOTE 1. See figure 80 for sag adjutter assembly NOTE 2. Plats are used in pain. re 55. Seg adjuster plate: reference number 67/100 (minimum failing load 300 KN for a pair of plates) 53BS 3288 : Part2:1990 All dimensions are in millimetres. NOTE 1. See figure 80 for sag adjuster assembly. NOTE 2. Plates re used in pairs, Figure 56. Sag adjuster plate: reference number 67/101 (minimum failing load 300 kN for a pair of plates) 54BS 3288 : Part2:1990 _-RSS RSS. RSS Tholes 232 a 125 RSS =“ {All dimensions are in millimetres. NOTE 1. See figure 81 for sag adjuster ewembly NOTE 2. Plates are used in pars Figure 57. Sag adjuster plate: reference number 84/100 (minimum failing load 400 kN for a pair of plates) 55BS 3288 : Part 2: 1990 Figure 68. Sag adjuster plate: reference number 84/101 (minimum failing load 400 KN for a pair of plates) 25 ow 67 (38) pe yes ore fs a (22-4 {Al dimensions are in miimetes. “K 150 150 Lo Figure 59. Yoke plate: reference number 15/22 (minimum failing load 70 kN) 56BS 3288 : Part 2: 1990 152 83 1 holes OR 3 holes 28 RS) ot (R75) (35) All dimensions are in milimeties. Figure 60. Yoke plate: reference number 42/82 (minimum fi 25) 250 250 222 ling load 190 KN) 57BS 3288: Part2: 1990 25 ns OAs R32 207 R25 [All dimensions are in millimetre. Figure 61. Yoke plate: reference number 86/122 (minimum failing load 260 kN} 58BS 3288: Part2:1990 2 holes on 250 250 Ras p All dimensions are in milimetres. Figure 62. Yoke plate: reference number 67/40 (minimum failing load 300 kN) 59BS 3288: Part2:1990 Zholes O18 NOTE. Pins, Pin with washer and split pin or hex. bolt with nut and split pin All dimension Zholes 218 lit pins and washers (or bolts, nuts and split pins) are included. Figure 63. Yoke plate: reference numbers 28/22, 42/22 and 42/124 \ BE N \ the Pin with washer and | splir"pin or hex. bott with out and split pin RG ‘Table 27. Dimensions of yoke plat 28/22, 42/22 and 42/124 Aateranee | Minimum [oa a lo [o Joele [a |w | rma Botts (2) umber | telling toed Diameter] Length | Diameter | Length iN en | rm |mm | ram | mem | mem | mm | mem | em | mm mm 2e22 | 125 2 |1s| 8 | 185/18 | 45 | 225) 150| 16 so | me | 65 4222 | 190 24 | 20 | 10 | 215] 22 | 7 | 285) 150 | 20 60 | m0 | 75 aziza | 190 24 | 20 | 10 | 215] 22 | 57 | 285) 200 | 20 eo =| M20 | 75 60BS 3288 : Part 2: 1990 2 R25. =o 2 holes @ 29 All dimensions ae in millimetres. Figure 64. Yoke plate: reference number 28/43 (minimum failing load 125 kN) 61BS 3288 : Part 2:1990 2 380 230 RST. a2 380 Tholes @ 26 All dimensions are in millimetres. Figure 65. Yoke plate: reference number 84/40 (minioum failing load 400 kN) 62BS 3288: Part2: 1990 102 tet le R32 B21 254 har 27 {All dimensions are in millimetre. Figure 66. Yoke plate: reference number 84/41 (minimum faiting toad 400 kN) 63BS 3288 : Part2:1990 02 254 - 2 holes 27 All dimentions ae in millimetres. Figure 67. Yoke plate: reference number 84/42 (minimum failing load 400 kN) 64BS 3288 ; Part 2:1990 2holes 22 All dimensions are in millimetres Figure 68. Yoke plate: reference number 42/42 (minimum failing load 190 kN) 65BS 3288: Part2:1990 RST 932 3 holes 218 holes 22 All dimensions are in millimetres. Figure 69. Yoke plate: reference number 84/52 {minimum faiting toad 400 kN} 66BS 3288 ; Part2: 1990 100 25 R32 150 R57 . 2 150 S holes w18 Zholes 827 R32 {All liner dimensions arin millimetre. Figure 70. Yoke ( late: reference number 84/53 imum failing load 400 kN) 67BS 3288 :Part2:1990 ——— ET TP PITTI {LEELA 68BS 3288 : Part2:1990 (Nt 00 Peo] Buy)165 whuswuiw) ge/pg sequinU sousie4es :axe/d BxOK wssO}!ONIG “Zz ANB ‘papnyou! ave (Sud es pue ny ‘5309 10) taysem pus ALK sud 4s puD sinu yum s}oq xay SLX 02H 40 suid 4nds pu Si2YSDM WIR Ud 09 « OZE papram pue Payjors sayeid 69BS 3288 : Part 2: 1990 so en y ir aay ziBS 3288: Part 2:1990 oer} 109) | tear | sez} oz | uz] con sai] acorve osz)| zai | sy | szzy) | saz) az 6 | yeotee, wsz)] -| os | sz] al sal a oe | vorer wus} ww | ww | ae | ws | us | wa Na ‘aus a{o| 4| a] of} we] wv sexonpuog denis edt pasoys pue adh sodas :tro.onpuoo yee 404 dens odAa posoya pue Apoq duieyp uotsuadsns yo suoteuowiig “gz 9142), adh pasoiy dens dwepp uojsusdsng | aypu aas | (ea wy oh sd0y ‘Apog dua suading nBS 3288: Part2:1990 ws} -| wa] siz ‘s9n) szt| srorve (dha wade) 221 ws | | wa] siz sot voor pe o | | sz| su a wots o| 4] a] al oe v sorenpucg 10109 ada 49d204 :sso1onpuco ‘ques pus ou 40} dea3s adAi uado pue Apoq dweso uorsuadsns jo suotsuouiig “6z 21921 ‘denis adAa uedo pur 2215 euosoa adAs s0do0y :tso.9npUoD yBze9 Pu adh vad, denis dejo uoisuadsng HE : rik “8 ‘dens adhs uedo pue Apoq dues uossusding “gz 2n61.3 ‘Ayo suoneays 12010} paso 61 puog 189 20} Go, ry aon ost oe ajau 2a 4 / 310N (s3}0q 9945 evo.09 yam) ada sada0y, ‘Ap0q dwe}9 uolsuadsng 72BS 3288 : Part 2: 1990 spjonpuca jo}. iD dé aysieng ‘dens dweyp uossuadsng %5 ‘2014 2u0J09 1ed-0m| ‘Apoq dweja vosuedsng, 73BS 3288 : Part2:1990 42/100 Links 42/02 190KN tower shackle or swivel Pin H Pin L All dimensions arin milimetces. sano NOTE. See figures 83 and 84 for details of pins. Figure 77. Sag adjuster assembly with 190 kN insulator units: single conductor 400kN tower swivel All dimensions are in millimetres. NOTE. See figuros 83 and 84 for detalls of pins. Fi ‘Soq adjuster assembly with 190 kN intulator units: vertical pair of conductors 74BS 3288 : Part2:1990 an AAR NN - hf 4 | 42/100 421 \ 508 TEAL pater ag {All dimensions are in millimetre. NOTE. Seo figures 83 and 84 for details of pins. Figure 79. Sag adjuster assembly with single 400 KN intulator units: vertical pair of ‘conductors (two #99 edjusters) 75BS 3288 : Part2:1990 617100 67/101 (20) gat or pine (2FFl with spacer Bolt or pin P Bolt or pin & s00kKN Links Maintenance tink N tower swivel 67/87 265 min 435 maxf 7m steps All dimensions are in millimetres. NOTE 1, See figure 85 for details of pins or bots NOTE 2. See figure 86 for details of spacer. Figure 80. Sag adjuster assembly with 300 kN insulator unit 84/100 24/101 (2 off (off Bolt or pin S Bolt or pin S Bolt or pin @ with spacer 400KN Maintenance ink SM tower svivel [All dimensions are in millimetres, NOTE 1. See figure 85 for details of pins or bolts. NOTE 2. See of spacer, smbly with single 400 kN insulator units 76BS 3288 : Part 2:1990 Hg “ {All dimensions are in 209 min. 308max)(6a™ steps) 42/101 300 (2off) (otf 42/54A or 427/548 (opp. twist) 127286 NOTE. Soe figures 83 and 84 for details of pins. Figure 82. Sag adjuster assembly with 3 400 KN insulator Units: vertioal pair of conductors (single sag adjusters) 7BS 3288: Part2: 1990 6.3 split pins in @Bholes a o2s) + t. t i 2 25 25 2 “Indicates whore reference letter isto be stamped. All dimansions are in millimetres, Figure 83. Sap adjuster/shackle pins H, L and M complete with washers and split pins (minimum failing load 190 kN) Table 31. Dimensions of sag adjuster/shackle pins H, LL and M complete with washers and split pins Reference a H 70 L 92 M 6 78BS 3288 : Part 2:1990 6.3 split pin ine hole 2 96.3 split pin in @8 hole 20) 6 | “Indicates where reference letter Isto be stamped. All simentions are in ilies. Figure 84. Sag adjuster/link pin J complete with washer and split pin (minimum failing toad 190 kN) “indicates where reference letter is to be stomped. [All dimensions are in millimetres. Figure 85, Sag adjuster pins/bolts P, Q, Rand S ‘complete with washer and split pin ‘Table 32, Dimensions of s09 adjuster pins/bolts P, Q, Rand S Reference | Minimum | Pin Bolt falling load Diameter, © | Length, KN am mm mm P 300 2 70 | 27 100 a 400 30 75 | M30 100 R 300 7 9 | wz? 120 5 400, 30 100 | 30 125 ‘Toble 33. Dimensions of spacer for sag adjuster pins/bolts R and S 0 we i Pinon [eo |L reference 8 2 «| 25 s a [26 Figure 86. Spacer for sag adjuster pins/oolts R and S 79BS 3288 : Part2:1990 19) (a) Single point 218 (6) Double point All dimensions are in millimetres, Figure 87. Typical arcing hor fisg 80BS 3288: Part2:1990 1? wo oF or ire 89. Bolt and split pin Figure 88. Clevis pin and split pin Table 34, Dimensions of clevis pin and split pin Nomint |e Nominal spit | Split pin in size pinsize ange iameter, D 16 6 8 32 20 6 5 22 2 10 63 40 24 10 63 40 25 12 63 40 2 12 63 0 30 2 63 cy Teble 35. Dimensions of bolt and split pin ‘Nomina! size | Screwed Tolerance, P |e Spit and threed | length, fin in enath me 8 20 6 32 M20 7 25 6 22 Maz 38 25 10 40 za 35 30 10 40 a7 38 30 10 50 M30 0 35 10 50BS 3288: Part2:1990 Appendices Appendix A. List of insulator set fittings Description Minimum ——Rafronce Figure Dasetiption Miimum Reference Faure iogloud number number failing load amber aN kw Shackle 0 16/20 7 Twistedelevircovie 70 18/29 as 70 15/129 7 125 2 35 7 15129 é 138, am 38 125 20/20 7 190 aa 37 125 zayr08 ? 300 97/23 38 180 S212 7 400 e423 3 180 anit 7 180 rar 3 Aaiotor i 19278,corD 38 300 87/103 3 125 wre a 135, 2818 38 Shackle (tower) 125 20/4 ° 180 a8 3 Texminatingsrip 20 418940841 300 ore 8 Section rap 20 190 2 Baltendednook 20 4198 10 70 15132 " Single ink 10 18/00 ro 70 18181 2 135 20/80 2 180 476 2 Balhendedeye link 70 15/90 13 300 7/08 2 70 16/82 4 125 28/30 ro Single conversion tink 190 ans “ 190 42130 3 130 aia 5 125 2e/980 4s 190 42/884, Borc 48 Bal ces 10 15725 v7 300, e768 4 7 15/83 18 00 bares a 138 28/83 8 400 a8 18 135 2aye0 “6 400 aes 6 490 42789 “6 300 07a ae Ba tongue 300 enue 19 400 a8 19 Ceanked inks 10 15/07 a 125 2087 a Socket cevis 7 151 2 138 2a/r004 2 % 15/4 20 480 22107 a 125 a 180 eae ® 125 20 300 ever ” 180 2 400 eurioe 3 190 20 190 2 Landing pate 70 1521 0 190 20 125 20/21 50 190 20 190 ari 50 300 2 400 Pr Sag adurtrpiste 70 5/101 5 400 20 135 28/100 5 190 427100 3 Twisted socket cevis 125 2onaia 2s 190 santos se 300 877100 55 Socket tongue 1 15/35 300 e701 56 70 19785 +400 84/100 a 125 BWS6A, Bore 26 400 aart01 = 135, 2arrae 28 180 aans 28 Yoke plate 20 18/22 190 a2a8 2 138 26/22 190 42/81 2 12 fen 190 am Clevintorgue 128 20/20 2 190 fame 190 42/26a,80rc 30 190 ise 190 S215tn‘orB 31 130 aaiiae 190 a2geaers 31 250 56/22 180 ans 3m 300 e740 400 ene Eaniwire adaptor 128, 28/508 2 400, a8 125 28/408 3 400 e440 400 eat Twisted cevietongue 190 som a 400 B42 400 e443 00 ears 400 “153 82BS 3288 : Part 2: 1990 Appendix B. List of insulator set fittings in order of reference number Reference Description Figure Reference Description umber number number 4(e8 Ball-ended hook 10 42/34 Shackle 9 4189 Terminating strap a1 42135 Socket tongue 26 4/90 Strap section and terminal 42 42/36 Socket tongue 26 42/37 Socket clevis 20 15/21 Landing plate 50 42/39 Clevis tongue 31 19/22 Yoke plat 59 42/42 Yoke plate 68 1/23, ‘Twisted clevis-clevis 35 42/44 Ball-ended eye link. 16 15/25 Ball clevis 7 42/45 Socket clevis 2 18/27 ‘Adaptor 38 42/46 Socket clevis 20 15/29 Shackle 7 42/51 Socket tongue 27 15/30 Ball-ended eye link 3 42/52 Yoke plate 60 15/31 Socket clevis 2 42/54 Clevis tongue 31 15/32 Ball-ended hook 1" 42/86 ‘Single link 43 16/33, Shackle 8 42/87 Cranked links 4a 16/35 Socket tongue 26 42/88 Parallel inks 45 15/81 Ball-ended hook 12 42/89 Parallel conversion links 46 15/82 Ball-ended eye link 14 42/100 Sag agjuster plate 53 15/83, Ball clevi 16 42/101 ‘Sag agjuster plate 54 15/84 Socket clevis 20 42/102 ‘Cranked links 48 15/85 Socket tongue 28 42/103 Shackle 7 15/86 ‘Single link 43 42/104 Socket clevis 20 15/87 Cranked links a7 42/115 Conversion fink 44 15/101 Sag adjuster plate 61 4/124 Yoke plate 63 16/129 Shackle 7 42/129 Shackle 7 42/139 Clevis tongue 31 28/21 Landing plate 50 28/22 Yoke plate 63 56/122 Yoke plate 6 28/23 ‘Twisted clevis-clevis 35 28/24 Twisted clevis-clevis 36 67/23 ‘Twisted clevis-clevis 38 28/27 Adaptor 38 67/31 Socket clevis 23 28/28 Clevis tongue 29 67/34 Shackle 9 28/29 Shackle 7 67/40 Yoke plete 62 28/30 Ball-ended eye link 13 67/48 Ball tongue 19 28/31 Socket clevis a 67/86 Single link 43 28/34 Shackle 9 67/87 ranked links 47 28/36 Socket tongue 26 67/88 Parallel links 45 28/37 ‘Socket clevis 20 67/89 Parallel conversion links 48 28/408 —_—_Earthwire adaptor 33 67/100 Sag adjuster plate 55 28/43 Yoke plate 64 67/101 Sag adjuster plate 56 28/47 Adaptor 38 67/103 Shackle 7 28/508 _—_Earthwire adaptor 32 28/83 Ball clevis 16 84/22 Yoke plate n 28/86 ‘Single link 43 24/23 Twisted clevie-clevis, 35 28/87 Cranked links 47 94/25 Ball clevis 18 28/884 raed links 45 84/31 Socket clevis 24 28/89 Parallel conversion links 46 84/37 Socket clevis 20 28/100 Sag adjuster plate 52 84/38 Yoke plate 2 28/108 Shackle (dee) 1 84/40 Yoke plate ca 28/1314 Twisted socket clevis 25 34/41 Yoke plate 66 28/135 Socket tongue 26 84/42 Yoke pl 67 28/186 ranked links 49 34/43 Yoke plate 73 84/48 Ball tongue 19 42/2 Landing plate 50 84/52 Yoke plate 69 42/22 Yoke plate 63 84/53 Yoke plate 70 42/23 ‘Twisted clevis-clevis 37 24/83 Bell clevis, 16 42/27 ‘Twisted clevis-tongue 34 94/88 Parallel links 45, 42/28 Clevis-tongue 30 84/100 ‘Sag adjuster plate 87 42/29 Shackle 7 84/101 Sag adjuster plate 58 42/30 Ball-ended eye link 3 84/102 ranked links 48 42/31 Socket clevis a 8384 blank‘Specification for beck bolts, acraws and nuts, hexagon and square, with B.S.W. threeds, and partly machined bolts, ‘screws and nuts, Nexagon and squere, with B.8.W. or B.S.F. threads ‘Specification for wrought stels for mechanical and elle engineering purposes art 4 Valve etels art 1 Performance and general requirements Pare 3 Dimensions of ball and vocket couplings of string inauistor units are 4 Locking deviees for ball and eocket couplings of string insulator units: dimensions and tests 18S 3643150 metric trow threeds Pare 2 Specification for selection imits of size 185.4190 Specification for 180 metric black hexagon bolts srews and nuts BS 4320 Specification for metal washere for general engineering purposes. Metric ser *Obsoleecentof the Power Electrics! Engineering Standards Policy Committee, wat published under the authority ofthe Board of BSI end comes into effect on 30 April 1090 © British Standards Inetitution, 1980 First published May 1965 First vision January 1977 Second revision Abril 1880 ISBN 0 580 17548 0 “The following BSI references relate to the work on this standerd: (Committed reference PEL/70 Draft for comment 86/20881 DC British Standards Inetitution, Incorporated by Royal C the independent nttional body for the preperation of Bri Standards ti the UK mamber of the Internetionel Organization {for Standerdization and UK spontar of the British Nations! Committee of the international Electrotechnical Commiesin, In adaition tothe preparation and promulgation of standd, coffers specialist services including the provision of information {through the BSI Library and Standard Datebase; Technical Holp tw Exporters and other services. Advice can be obtained from the Enquiry Section, BSI, Milton Keynes MK14 GLE, telephone (0808 221166, tiex 825777 Copyright. Users of British Stancerds are reminded thet copyright fubsitts in ll BS! publications. No art of this publication may be BS 3288: Part 2: 1990 ‘produced in any form without the prior perminsion in writing of BSI. This does not praclude the fre wae, n the courte of implementing the standerd, of necessary details such ox symbols and size, type oF grade designations. Enquiries should be addrewed to ‘the Publics MK14 BLE. The number for telephone enquiri ‘9nd for telex 625797. Contract raquraments A Britith Standard does not purport to Include all the necesury pro onraet. Users of Standerds ae responsible Tor thelr correct application Revision of British Standards. British Standards are revised, when pecetsary, by the isue o ts oF of revised editions {tis important that users of British Standards should ascertain that ‘they are in posession ofthe latest amendments or editions. ‘Automatic updating service. BS! prov tnd sutomatie standards updating service ealeg PLUS, Details sre available from BSI Enauiry Section at Milton Keynes, telephone (2908 221166, telex 825777. Information on all BS! publications iin the BS! Catalogue, supplemented each month by BS! News which is avalabie to subscribing members of BSI and gives details of new publications, revisions, amendments nd withdrawn standards, Any person who, ‘when making use of « British Standard, encounters an inaceuracy oF lembiguity, requested to notify BSI without delay in order tht the matter may be investigated an appropriate action taken, Committees responsible for this British Standard ‘The preparation of this British Standard wes entrusted by the Power Electrical Engineering Standards Policy Committe (PEL/:) 10 Technical Committee PEL/70, upon which the fllowing bodies wore represented: ‘Association of Consulting Engineers ‘Association of Manutecturers Allied to the Electrical and Electronic Industry (BEAMA Ltd.) Brith Caramic Reseerch Li, ish Industral Ceramic Manufacturer’ Associetion Department of Energy (Electricity Division) Amendments issued since publication Electrical and Electronic intulation Association (BEAMA Ltd.) Electricity Supply Industry In England end Water ‘Tranemission and Distribution Astociation (BEAMA Ltd.) ‘The following bodies were alto represented in the drafting of the ‘standard, through subcommittees and panels: Aluminium Federation British Rellways Bosrd ‘National Associstion of Malleable Ironfounders (Overhead Transmission Line Contractors ‘Amd, No. Date of issue | Text affected British Standards Institution « 2 Park Street London W1A 2BS - Telephone 01-629 9000 - Telex 266933 9006-10 PELITO O66L:Z Hed: 88zE Sa