TECHNICAL STANDARD
API6D Ball & Plug Valve
Inspection & Test Procedure
Global Supply Line Pty Ltd ABN 86 008 134 512
69-71 Barndioota Rd Salisbury Plain South Australia 5109 Phone +61(0)8 8285 0000 Fax +61(0)8 8285 0088 www.globalsupplyline.com.au
V A LV E S A N D P I P E L I N E S U P P L I E S
Scope
1.1
Valve Range
Type:
Body:
Material:
This standard provides specific inspection items to be performed on all ball & plug valves.
The valves shall be provided with a serial numbering system and will be documented for
traceability purposes.
Pressure rating:
Bore dia:
Floating & trunnion ball and lubricated plug
Split body 2p & 3p and top entry
Cast & forged, carbon steel, stainless steel, alloy steel & duplex
steel
ASME Class 150, 300, 600, 900, 1500
NPS 1 to 24 full bore
NPS 3 to 24 reduced bore
1.2
Applicable Code and Standard
Valve Design: API6D, ASME B16.34, API607, API608
Face to Face Dimension: ANSI B16.10
End Flange Dimension: ASME B16.5
Inspection and Test: API6D
Non Destructive Examination (NDE): ASME B16.34 (if required on purchase order)
Radiographic Examination (RT)
Liquid Penetrant Examination (PT)
Magnetic Particle Examination (MT)
Ultrasonic Examination (UT)
2.
Inspection Items
Inspection items are as follows:
Material test;
Visual inspection;
Dimensional check;
Assembly/performance test;
Pressure test;
(1) Hydrostatic Shell Test
(2) High Pressure Valve Closure Test
(3) Low Pressure Valve Closure Test
Final Inspection,
NDE (if required)
3.
Material Test
GSL/QTY-JH-03
The materials of body, body cap, ball and stem shall be confirmed to meet the respective
material specifications on the basis of respective mill certificates.
4.
Visual Inspection
Check visually that:
4-1.
Casting surfaces (both the exterior and interior) are free from holes, burrs, scale, cracks, etc. in
accordance with MSS SP55.
Machined faces and all surfaces are free from flaws or unevenness on finished surfaces.
The fluid passage is finished appropriately and free from foreign debris.
Angles and corners the dimensions of which are no specified in the drawings and standards are
chamfered and rounded appropriately.
The nominal pressure, nominal diameter, and other necessary information should be properly
indicated on the body surface and label.
The flow direction shall be properly indicated when restricted.
Bore should be unobstructed when valve is in full open position.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
GSL/QTY-JH-06
Page 2
GLOBAL SUPPLY LINE
5.
5-1.
5-2.
5-3.
Dimensional Check
GSL/QTY-JH-05
Dimensions shall be checked in accordance with the drawings and specified values.
The dimensional tolerance of flanges shall be as specified in ASME B16.5, buttweld end to ANSI
B16.25.
The tolerance of the face-to-face dimension shall be in accordance with API6D (Table 1).
Table 1 Face-to-face dimensional tolerance (unit: mm)
Nominal
NPS
NPS
6.
6-1.
6-2.
7.
diameter of valve
10 less than
12 to 24
Dimensional tolerance
2 mm
3 mm
Assembly/Torque Test
GSL/QPS8.2-02
The valve operating torque shall be determined prior to pressure test, without load and in dry
condition.
The operating torque shall be within the GSL specified range.
Both the directions of the hole in the ball and the two faces of the stem of the flow direction
indication at the stem top shall coincide with each other.
GSL/QPS8.2-01
Pressure Test
Testing Requirements
Item
Hydrostatic Shell Test
High Pressure Closure Test (Hydrostatic)
High Pressure Closure Test (Gas)
7-1.
Ball & Plug Valve
Yes
Yes
Yes
Hydrostatic Shell Test
With the valve kept half open, fill the body with water and apply test pressure shown in Table 2.
Make sure that the connections are tight then use leak detector spray on all body joins & body
surfaces to ensure zero leakage and all parts are free from leakage.
At this time, the test duration shall be as shown in Table 3.
For stainless steel and the duplex stainless steel valves, the chloride content of test water shall
not exceed 30 ppm by mass.
Table 2 Shell test (API6D/ASME B16.34( [unit MPa]
Material of Shell
150lb
300lb
600lb
900lb
1500lb
WCB/A105N
LCB/LF2
CF8, CF8M/316/304
LC3/LF3
3.14
2.84
2.94
3.14
7.58
7.26
7.65
7.85
15.4
14.51
15
15.59
23.14
21.77
22.46
23.34
38.44
36.09
37.27
38.83
Table 3 Test duration for shell test and closure test (API6D) [unit min]
Size
(NPS)
1/2 ~ 4
6 ~ 10
12 ~ 18
20
Testing
Item
Hydrostatic Shell Test
High Pressure Valve
Closure Test
(Hydrostatic)
Low Pressure Valve
Closure Test (Gas)
2
5
15
30
2
5
5
5
2
5
5
5
Page 3
GLOBAL SUPPLY LINE
7-2.
High Pressure Valve Seat Test (Hydrostatic)
With the valve closed fully, test in both directions, one direction at a time at pressure given in
Table 4.1. Use leak detector spray on entire area to ensure zero leakage.
The test duration shall be as shown in Table 3.
Note: For stainless steel and the duplex stainless steel valves, the chloride content of test water
shall not exceed 30 ppm by mass.
Table 4.1 All valves (API6D/ASME B16.34) [unit MPa]
Pressure
NPS
1/2 ~ 24
7-3.
7-4.
150lb
300lb
600lb
900lb
1500lb
2500lb
2.26
5.79
11.46
17.16
28.54
62.1
Low Pressure Valve Seat Test (Gas)
With the valve closed fully, test in both directions, one direction at a time at pressure of 0.6Mpag.
Use leak detector spray on entire seal area to ensure zero leakage.
The test duration shall be as shown in Table 3.
Acceptance Criteria of Closure Test (ISO5208)
Seat
Leakage Rate
Soft Seated
0 Leakage (A)
Metal Seated
01mm3/SxDN (D)
7-5.
After Pressure Testing
The test water is to be entirely evacuated from valve bore.
For carbon steel valves, the interior of the valve is to be sprayed or coated with rust preventative
oil to prevent rust and corrosion during transit and storage.
8.
8-1.
Final Inspection
GSL/QPS8.2-04
Paint Check
1) The paint check shall be made after the above mentioned tests have been completed.
2) Check that finished coast is free from peeling, unevenness, blistering, etc.
3) Specification and colour hall be in accordance with customers specifications. Unless other
wise specified, it shall be in accordance with the GSL standards.
Ensure that all marking and tagging are correct.
Body finish of casting/forging to be physically inspected in accordance with MSS-SP55.
8-2.
8-3.
9.
Non Destructive Examination (Supplementary Examination)
GSL/QPS7.5-02
Supplementary types of non destructive examination are required only if specified in the purchase
order and only to the extent specified.
Magnetic Particle, Radiographic, Liquid Penetrant and Ultrasonic Examination of steel castings
or forgings shall be in accordance with specification in client purchase order.
~ Major valve stockists supplying worldwide ~
http://www.globalsupplyline.com.au
Page 4
API6D-Valve-Inspection-Test R3 - AA
GLOBAL SUPPLY LINE
