[Link].
com
Table A005-15/E
Vane pumps type PFE-31, PFE-41, PFE-51
fixed displacement - cartridge design
PFE-*1 are fixed displacement-twelvevane pumps, cartridge design
with integral hydraulic balancing for
high pressure operation, long service
life and low noise level.
IN
OUT
They are available in three different
sizes with max displacements up to 44,
85 and 150 cm3/rev and single, multiple
or with through-shaft configurations.
Mounting flange according to SAE
J744 standard.
body
rotor with vanes
balanced plates
shaft
inlet port
outlet port
Inlet and outlet ports can be oriented in
four different positions to match any
installation requirement.
Simplified maintenance as the pumping
cartridge can be easily replaced.
PFE-41
Max pressure 210 bar.
MODEL CODE
PFE
X2
31
036
/31028 /
**
Fixed displacement vane pump
Additional suffix for multiple pumps:
X2 = double pump composed of single vane pumps
X3 = triple pump composed of single vane pumps
Series number
Eventual suffix for pumps with through shaft:
XA = for coupling one PFE-31
XB = for coupling one PFE-41 (only for PFE-41 and PFE-51)
XC = for coupling one PFE-51 (only for PFE-51)
XO = with through shaft, without rear flange
Note:mulitple pumps are assembled in decreasing order of
size. See also tab. A190.
Port orientation, see section :
T = standard
U, V, W = on request
Direction of rotation (viewed from the shaft end):
D = clockwise (supplied standard if not otherwise specified)
S = counterclockwise
Note: PFE are not reversible
Size, see section :
31, 41, 51
Drive shaft, see section and :
cylindrical, keyed for single and multiple pump (only first position)
1 = standard
2 = long version (only for PFE-41 and PFE-51)
3 = for high torque applications
splined
5 = for single and multiple pumps (any position)
6 = for single and multiple pumps (only first position)
only for PFE-31
7 = for second and third position in multiple pumps
and PFE-41
Displacement [cm /rev], see section
for PFE 31: 010, 016, 022, 028, 036, 044
for PFE 41: 029, 037, 045, 056, 070, 085
for PFE 51: 090, 110, 129, 150
3
Only for multiple pumps PFEX*: type of second (and third) pump
/*
Seals material:
omit for NBR (mineral oil
& water glycol)
PE = FPM
OPERATING CHARACTERISTICS at 1450 rpm (based on mineral oil ISO VG 46 at 50C)
Model
PFE-31010
PFE-31016
PFE-31022
PFE-31028
PFE-31036
PFE-31044
PFE-41029
PFE-41037
PFE-41045
PFE-41056
PFE-41070
PFE-41085
PFE-51090
PFE-51110
PFE-51129
PFE-51150
Displacement
cm3/rev
10,5
16,5
21,6
28,1
35,6
43,7
29,3
36,6
45,0
55,8
69,9
85,3
90,0
109,6
129,2
150,2
Speed range
Max
rpm (2)
pressure (1)
160
800-2400
800-2800
210 bar
800-2500
800-2000
800-2200
800-1800
7 bar (3)
l/min
kW
15
23
30
40
51
63
41
52
64
80
101
124
128
157
186
215
0,2
0,5
0,6
0,8
1
1,3
0,8
1
1,3
1,6
2
2,4
2,7
3,2
3,7
4,2
70 bar (3)
l/min
kW
13,5
21
28
38
49
61
39
50
62
78
98
121
124
152
180
211
2
3
4
5,5
7
8
5,5
7
8,5
11
13,5
16
17
21
25
29
140 bar (3)
l/min
kW
12
19
26
36
46
58
37
48
60
75
95
118
119
147
174
204
5
5
7
10
12,5
15,5
10
12,5
16
21
26
32
33
40
47
55
210 bar (3)
l/min
kW
16
23
33
43
55
34
45
57
72
91
114
114
141
168
197
8,3
10,8
14
17,8
22
14,7
18,3
22,6
28
35
43
45
55
65
75
(1) Max pressure is
160 bar for /PE
version and water
glycol fluid
(2) Max speed is 1800
rpm for /PE
versions; 1500 rpm
for water glycol
fluid
(3) Flow rate and
power consumption
are proportional to
the rotation speed,
see section
A005
MAIN CHARACTERISTICS OF VANE PUMPS TYPE PFE-*1
Installation position
Any position
Loads on the shaft
Axial and radial loads are not allowed on the shaft. The coupling should be sized to absorb the
power peak.
Ambient temperature
from -20C to +70C
Fluid
Hydraulic oil as per DIN 51524...535; for other fluids see section
Recommended viscosity
max at cold start
max at full power
during operation
min at full power
Fluid contamination class
800 mm2/s
100 mm2/s
24 mm2/s
10 mm2/s
ISO 4401 class 21/19/16 NAS 1638 class 10 (filters at 25 m value with 25 75 recommended)
Fluid temperature
-20C +60C
Recommended pressure on inlet port
from -0,15 to 1,5 bar for speed up to 1800 rpm; from 0 to +1,5 bar for speed over 1800 rpm
-20C +80C (/PE seals)
DIAGRAMS (based on mineral oil ISO VG 46 at 50C)
2 = Ambient noise levels measured in
compliance with ISO 4412-1 oleohydraulics -Test procedure to define the
ambient noise level - Pumps
Shaft speed: 1450 rpm.
2
150
129
Noise level [dB (A)]
1 = Torque versus pressure diagram
Torque needed to operate the pump [Nm]
-20C +50C (water glycol)
110
090
085
070
056
045
036
028
022
016
010
PFE-51
PFE-41
PFE-31
Operating pressure [bar]
Operating pressure [bar]
044
PFE-31:
036
028
Flow [l/min]
4 = Power consumption versus speed
diagram at 140 bar. Power consumption
is proportional to operating pressure.
022
016
010
036
028
022
016
010
Rotation speed [rpm]
PFE-41:
Rotation speed [rpm]
Flow [l/min]
070
056
045
037
029
Power consumption [kW]
6
085
5 = Flow versus speed diagram with pressure variation from 7 bar to 210 bar.
6 = Power consumption versus speed diagram at 140 bar. Power consumption is
proportional to operating pressure.
085
045
037
029
150
129
110
Flow [l/min]
8 = Power consumption versus speed diagram at 140 bar. Power consumption is
proportional to operating pressure.
Rotation speed [rpm]
090
Rotation speed [rpm]
Power consumption [kW]
7 = Flow versus speed diagram with pressure variation from 7 bar to 210 bar.
070
056
Rotation speed [rpm]
PFE-51:
044
3 = Flow versus speed diagram with pressure variation from 7 bar to 210 bar.
Power consumption [kW]
150
129
110
090
Rotation speed [rpm]
PORT ORIENTATION
IN
Single pumps can be supplied with oil ports oriented in different configuration in relation
to the drive shaft, as follows (wiewed from the shaft end);
OUT
T = inlet and outlet ports on the same axis (standard)
U = outlet orientated 180 with respect to the inlet
V = outlet oriented 90 with respect to the inlet
W = outlet oriented 270 with respect to the inlet
IN
OUT
OUT
In multiple pumps inlet ports and outlet ports are in line.
Ports orientation can be easily changed by rotating the pump body that carries inlet port.
OUT
IN
DRIVE SHAFT
CYLINDRICAL SHAFT KEYED
1 = for single and multiple pumps (only first position)
supplied as standard if not specified in the model code
2 = for single and multiple pumps (only first position)
long version (only for PFE-41 and PFE-51)
3 = for single and multiple pumps (only first position)
for high torque applications
Keyed shaft type 1 (standard)
Model
A1
PFE-31
PFE-41
PFE-51
Keyed shaft type 2
Only for through
shaft execution
F
G1
Keyed shaft type 3
Only for through
shaft execution
Only for through
shaft execution
Z1
AQ
A1
G1
Z1
AQ
A1
8,00
19,05
SAE 16/32-9T
4,78
24,54 56,00
4,75
24,41
SAE 32/64-24T
6,36
25,03 71,00
8,00
22,22
SAE 32/64-24T
6,38
28,30 78,00 11,40 25,38
6,35
24,77
6,35
28,10
7,95
35,33 84,00
7,97
38,58 84,00
7,94
35,07
7,94
38,46
4,78
21,11 56,00
4,75
20,94
4,78
24,54 59,00 11,40 22,22
4,75
24,41
7,97
35,33 73,00
7,94
35,07
19,00
22,20
14
31,75
SAE 16/32-13T
31,70
22,20
8,10
31,75
SAE 16/32-13T
31,70
G1
Z1
AQ
8,00
22,22
SAE 16/32-9T
22,20
SAE 32/64-24T
25,36
14
34,90
SAE 16/32-13T
34,88
SPLINED SHAFT
5 = for single and multiple pumps (any position)
for PFE-31 according to SAE A 16/32 DP, 9 teeth;
for PFE-41 according to SAE B 16/32 DP, 13 teeth;
for PFE-51 according to SAE C 12/24 DP, 14 teeth;
6 = for single and multiple pumps (only first position)
for PFE-31 and PFEX*-31 according to SAE B 16/32 DP, 13 teeth;
for PFE-41 and PFEX*-41 according to SAE C 12/24 DP, 14 teeth;
7 = for second and third position pump in multiple configuration:
for PFEX*-31 according to SAE B 16/32 DP, 13 teeth;
for PFEX*-41 according to SAE C 12/24 DP, 14 teeth;
Splined shaft type 5
Splined shaft type 6
Only for through
shaft execution
Model
G2
G3
Z1
Splined shaft type 7
Only for through
shaft execution
AQ
G2
G3
Z1
Only for through
shaft execution
AQ
G2
G3
Z1
AQ
PFE-31
32,00 19,50
6,50 SAE 16/32-9T
SAE 16/32-9T
41,00
28
8,00 SAE 16/32-13T
SAE 16/32-9T
32,00
19
8,00 SAE 16/32-13T
SAE 16/32-9T
41,25
28
8,00 SAE 16/32-13T SAE 32/64-24T
55,60
42
8,00 SAE 12/24-14T
SAE 32/64-24T
41,60
28
8,00 SAE 12/24-14T
SAE 32/64-24T
56,00
42
8,10 SAE 12/24-14T SAE 16/32-13T
PFE-41
PFE-51
LIMITS OF SHAFT TORQUE
Maximum torque available at the
end of the through shaft [Nm]
Maximum driving torque [Nm]
Pump
model
Shaft type 1
Shaft type 2
Shaft type 3
Shaft type 5
Shaft type 6
Shaft type 7
Any type of shaft
PFE-31
160
240
110
240
240
130
PFE-41
250
250
400
200
400
400
250
PFE-51
500
500
850
450
400
The values of torque required to operate the pumps are shown for each type on the torque versus pressure diagram at section .
In multiple pumps the total torque applied to the shaft of the first element (drive shaft) is the sum of the single torque needed for operating each single
pump and it is necessary to verify that this total torque applied to the drive shaft is not higher than the values indicated in the table.
A005
DIMENSIONS OF SINGLE PUMPS [mm]
0
-0,05
T = inlet port
P = outlet port
SAE FLANGES
PFE-31: port T = 1 1/4; port P = 3/4
PFE-41: port T = 1 1/2; port P = 1
PFE-51: port T = 2;
port P = 1 1/4
Mass:
PFE-31 = 9 kg
PFE-41 = 14 kg
PFE-51 = 25,5 kg
SAE flanges can be supplied with the pump, see [Link], tab. SK155
Model
PFE-31
136
100
28
PFE-41
160
120
38
82,5
70
6,4
106
73
101,6
76,2
9,7
146
107
95
11,1
28,5
120
14,3
34
PFE-51
186,5
125
38
127
Model
U1
U2
82,6
12,7
181
143,5
148
17,5
35
W1
W2
J1
J2
X1
X2
PFE-31
114
58,7
47,6
10
32
19
30,2
22,2
M10X20
M10X17
47
PFE-41
134
70
52,4
13
38
25
35,7
26,2
M12X20
M10X17
76
PFE-51
160
77,8
58
15
51
32
42,9
30,2
M12X20
M10X20
76
DIMENSIONS OF PUMPS WITH THROUGH-SHAFT (FOR MULTIPLE PUMPS) [mm]
T = inlet port
P = outlet port
SAE FLANGES
PFEX-31: port T = 1 1/4; port P = 3/4
PFEX-41: port T = 1 1/2; port P = 1
PFEX-51: port T = 2;
port P = 1 1/4
For other dimensions, see section
Model
AG
AH
AL
Tightening
torque (Nm)(1)
AN
AP
AR
AS
6,42
6,47
165,5
132,5
79
32
28,5
PFEXA-31
114
106
M10X17
70
95
33
25
82,57
82,63
PFEXA-41
134
106
M10X17
70
95
23
11
82,57
82,63
6,42
6,47
194
171
73
32
28,5
18
101,62
101,68
9,73
9,78
203
171
107
41
34
6,42
6,47
206,2
183,5
73
32
28,5
PFEXB-41
134
146
M12
125
120
32
PFEXA-51
134
106
M10X17
70
95
22,7
11
82,57
82,63
PFEXB-51
134
146
M12
125
120
32
18
101,62
101,68
9,73
9,78
215,5
183,5
107
41
34
PFEXC-51
134
181
M16
300
148
46,5
30,7
127,02
127,02
12,73
12,78
230
183,5
143,5
56
35
(1) Tightening torque for screw class 12.9
09/12
