CHAPTER
Reinforced Concrete Design
Fifth Edition
REINFORCED CONCRETE
BEAMS: T-BEAMS AND
DOUBLY REINFORCED BEAMS
A. J. Clark School of Engineering Department of Civil and Environmental Engineering
Part I Concrete Design and Analysis
3c
FALL 2002
By
Dr . Ibrahim. Assakkaf
ENCE 355 - Introduction to Structural Design
Department of Civil and Environmental Engineering
University of Maryland, College Park
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 1
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
1. Establish the effective flange width, b
based on ACI criteria.
2. Check As,min. Use Table 1 (Table A-5,
Textbook).
3. Check the ACI Code ductility
requirements using the proper
expression for As,max from Eq. 1 or
Table 2 (Table 3-1, Textbook). As,max
must be larger than actual As.
Slide No. 2
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Table A-5 Textbook
f c (psi )
Table 1
Design Constants
3 f c 200
f y
f y
3,000
4,000
5,000
6,000
0.0050
0.0050
0.0053
0.0058
3,000
4,000
5,000
6,000
0.0040
0.0040
0.0042
0.0046
3,000
4,000
5,000
6,000
0.0033
0.0033
0.0035
0.0039
3,000
4,000
5,000
6,000
0.0027
0.0027
0.0028
0.0031
max = 0.75 b
Fy = 40,000 psi
0.0278
0.0372
0.0436
0.0490
Fy = 50,000 psi
0.0206
0.0275
0.0324
0.0364
Fy = 60,000 psi
0.0161
0.0214
0.0252
0.0283
Fy = 75,000 psi
0.0116
0.0155
0.0182
0.0206
Recommended Design Values
b
k (ksi)
0.0135
0.0180
0.0225
0.0270
0.4828
0.6438
0.8047
0.9657
0.0108
0.0144
0.0180
0.0216
0.4828
0.6438
0.8047
0.9657
0.0090
0.0120
0.0150
0.0180
0.4828
0.6438
0.8047
0.9657
0.0072
0.0096
0.0120
0.0144
0.4828
0.6438
0.8047
0.9657
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 3
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Table 2. Expressions for As,max (T-Beams)
f c (psi)
fy (psi)
As,max (in2)
40,000
0.582
0.0478h f b + bw
d 1
h f
60,000
0.503
0.0319h f b + bw
d 1
h f
3,000
40,000
4,000
60,000
0.582
0.0638h f b + bw
d 1
h f
0.503
0.0425h f b + bw
d 1
h f
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 4
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Q
The check the ductility of a T-beam, the
following equation can be used for
various combinations of f c and fy
As ,max =
0.638
f ch f b + bw b
fy
h f
87,000
d 1
87,000 + f
y
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
(1)
Slide No. 5
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
4. Compute the total tension in the steel:
N T = As f y
5. Compute the magnitude of the
compression that the flange its is
capable of furnishing:
N Cf = 0.85 f cbh f
6. If NT > NCf, the beam will behave as a
true T-beam, and the remaining
compression, which equals NT - NCf
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 6
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
will be furnished by additional web
area. If NT < NCf, the beam will behave
as a rectangular beam of width b.
Rectangular T-Beam
7. Compute the actual steel ratio in order
to find k :
As
bd
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 7
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
8. Consult the proper Table 3, (Tables A7 to A-11, Text) and find the required
k for the value from step 7.
9. Compute the practical moment
capacity Mn of the beam cross
section:
M n = bd 2 k
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 8
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Sample Values
Table 3.
Coefficient of Resistance
Table A-10 Textbook
k
0.0010
0.0011
0.0012
0.0013
0.0014
0.0015
0.0016
0.0017
0.0018
0.0019
0.0020
0.0021
0.0595
0.0654
0.0712
0.0771
0.0830
0.0888
0.0946
0.1005
0.1063
0.1121
0.1179
0.1237
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 9
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
True T-Beam
7. Determine the depth of the
compressive stress block:
NT N Cf
a=
+ hf
0.85 f cbw
8. (a) Locate the centroid of the total
compressive area referenced to top of
the flange using the relationship
Slide No. 10
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
y=
From which
Ay
A
Z =dy
Compute the practical moment
capacity Mn of the beam:
M n = N C Z
or NT Z
Slide No. 11
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Or
(b) Calculate Mn using a summation
of internal couples contributed by the
flange and the web:
hf
M n = N Cf d
2
a hf
+ (NT N Cf )d h f
Slide No. 12
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Q
Example 1: T-Beam Analysis
Determine the practical moment capacity
Mn for the T-beam in the floor system
shown. The beam span is 24 in. Use fy =
60,000 psi and f c = 3,000 psi. Check the
steel to ensure that it is within allowable
limits according to the ACI Code.
Slide No. 13
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Analysis of T-Beams
For Moments
Q
Example 1: T-Beam Analysis (contd)
4
24
3-#9
10
3-#9
5 0 (typ.)
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 14
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
1. Compute the design moment Mu.
2. Assume that the effective depth d is
equal to h 3 in.
3. Establish the effective flange width based
on ACI criteria.
4. Compute the practical moment strength
Mnf assuming that the total effective
flange is in compression:
h
M nf = (0.85 f c)bh f d f
2
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 15
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
5. If Mnf > Mu the beam will behave as
rectangular T-beam of width b.
Otherwise, the beam will behave as a
true T-beam.
Rectangular T-Beam
6. Design as a rectangular beam with b
and d as known values. Compute the
required k :
Mu
required k =
bd 2
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 16
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
7. From the tables in Appendix A of
textbook (see Table 3), determine the
required for the required k of step 6.
8. Compute the required As:
required As = bd
9. Select bars and check the beam width.
Check the actual d and compare it with
the assumed d. If the actual d is
slightly in excess of the assumed d,
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 17
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
the design will be slightly conservative.
If the actual d is less than the
assumed d, the design may be on the
nonconservative side (depending on
the steel provided) and should be
more closely investigated for possible
revision.
10. Check As,min. Use Table 1 (Table A-5,
Textbook).
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 18
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
11. Check the ACI ductility requirement
using the proper expression for As,max
from Table 2 (Table 3-1 Text) or Eq. 1.
Note that As,max must be larger than
actual As.
12. Sketch the design.
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 19
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
True T-Beam
6. Using an estimated df = h 3 in. and
Zf = df hf/2, determine the steel area
As required for the flange couple:
required Asf =
M nf
f y Z f
7. Design the web couple as a
rectangular reinforced concrete beam
10
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 20
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
having a total depth hw = h hf using
an estimated dw = hw 3 in. and a
beam width of bw. Design for an
applied moment Mu - Mnf.
Determine required k , required ,
and required Asw.
8. Total required Asw = Asf + Asw.
9. Select the bars. Bars must fit into
beam width bw. Check d as in step 9
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
Slide No. 21
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
of the rectangular T-beam design.
10. Check As,min. Use Table 1 (Table A-5,
Textbook).
11. Check As,max. Use Table 2 (Table 3-1,
Textbook) or Eq. 1.
12. Sketch the design.
11
Slide No. 22
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
Q
Example: T-Beam Design
Design a T-beam having a cross section
shown in the figure. Assume that the
effective flange width given is acceptable.
The T-beam will carry a total design
moment Mu of 340 ft-kips. Use f c = 3,000
psi and fy = 60,000 psi. Use 1.5-in. cover
and No. 3 stirrups.
Slide No. 23
CHAPTER 3c. R/C BEAMS: T-BEAMS AND DOUBLY REINFORCED BEAMS
ENCE 355 Assakkaf
Procedure for Design of T-Beams
For Moments
Q
Example: T-Beam Design (contd)
27
22
1
2
12
12
