SIGMACOVER 280
5 pages
DESCRIPTION
February 2010
Revision of September 2009
two component polyamide cured epoxy primer
PRINCIPAL CHARACTERISTICS general purpose epoxy primer in protective coating systems for steel and
non ferrous metals
good adhesion to steel and galvanised steel
good adhesion to non ferrous metals
good flow and wetting properties
good water and corrosion resistance
cures at temperatures down to +5C
suitable for touching up of weld seams and damages of epoxy coatings
during construction
excellent recoatability
can be overcoated with most alkyd-, chlorinated rubber-, vinyl-, epoxy- and
two component polyurethane coatings
suitable on wet blast cleaned substrates (damp or dry)
compatible with well designed cathodic protection systems
COLOURS AND GLOSS
yellow/green (redbrown on request) - eggshell
BASIC DATA AT 20C
(1 g/cm = 8.25 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.3 g/cm
57 2%
max. 327 g/kg (Directive 1999/13/EC, SED)
max. 432 g/l (approx. 3.6 lb/gal)
50 - 100 m depending on system
11.4 m/l for 50 m, 5.7 m/l for 100 m *
1.5 hour
min. see tables *
max. see tables *
7 days *
Mass density
Volume solids
VOC (supplied)
Recommended dry film thickness
Theoretical spreading rate
Touch dry after
Overcoating interval
Full cure after
(data for components)
Shelf life (cool and dry place)
at least 24 months
* see additional data
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
for immersion exposure:
steel or steel with not approved zinc silicate shop primer; blast cleaned
(dry or wet) to ISO-Sa2, blasting profile 30 - 75 m
steel with approved zinc silicate shop primer; weld seams and areas of
damaged shop primer or breakdown should be blast cleaned to ISOSa2, blasting profile 30 - 75 m or power tool cleaned to SPSS-Pt3
coated steel; hydrojetted to VIS WJ2 L (blasting profile 40 - 70 m)
page 1/5
SIGMACOVER 280
February 2010
IMO-MSC.215(82) Requirements for Water Ballast Tanks:
steel; ISO 8501-3:2006 grade P2, with all edges treated to a rounded
radius of minimum 2 mm or subject to three pass grinding
steel or steel with not approved zinc silicate shop primer; blast cleaned to
ISO-Sa2, blasting profile 30 - 75 m
steel with approved zinc silicate shop primer; weld seams and areas of
damaged shop primer or breakdown should be blast cleaned to ISOSa2, blasting profile 30 - 75 m
for shop primer with IMO type approval; no additional requirements
for shop primer without IMO type approval; blast cleaned to ISO-Sa2
removing at least 70% of intact shop primer, blasting profile 30 - 75
m
dust quantity rating "1" for dust size class "3", "4" or "5", lower dust size
classes to be removed if visible on the surface to be coated without
magnification (ISO 8502-3:1992)
for atmospheric exposure conditions:
steel; blast cleaned to ISO-Sa2, blasting profile 30 - 75 m or
according to ISO-St3
shop primed steel; pretreated to SPSS-Pt3
galvanised steel; cleaned from grease, salts, contamination and
roughened up
substrate temperature should be above 5C and at least 3C above dew
point during application and curing
maximum relative humidity during application and curing is 85%
SYSTEM SPECIFICATION
marine
system sheets: 3101, 3102, 3103, 3104,
3105, 3106 (spec. 5,7), 3107, 3108
INSTRUCTIONS FOR USE
mixing ratio by volume: base to hardener 80 : 20
the temperature of the mixed base and hardener should preferably be above
15C, otherwise extra solvent may be required to obtain application viscosity
too much solvent results in reduced sag resistance and slower cure
thinner should be added after mixing the components
Induction time
Pot life
none
8 hours at 20C *
* see additional data
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Thinner 91-92
0 - 10%, depending on required thickness and application conditions
approx. 0.46 mm (= 0.018 in)
15 MPa (= approx. 150 bar; 2130 p.s.i.)
page 2/5
SIGMACOVER 280
February 2010
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Thinner 91-92
0 - 10%, depending on required thickness and application conditions
1.5 - 2 mm
0.3 - 0.4 MPa (= approx. 3 - 4 bar; 43 - 57 p.s.i.)
BRUSH/ROLLER
Recommended thinner
Volume of thinner
no extra thinner is necessary,
but up to 5% Thinner 91-92 can be added if desired
CLEANING SOLVENT
Thinner 90-53
SAFETY PRECAUTIONS
for paint and recommended thinners see safety sheets 1430, 1431 and relevant
material safety data sheets
this is a solvent borne paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed skin
or eyes
ADDITIONAL DATA
Film thickness and spreading rate
theoretical spreading rate m/l
11.4
7.6
5.7
dft in m
50
75
100
max. dft when brushing:
50 m
Overcoating table for SigmaCover 280 for dft up to 100 m
with various two pack epoxy- and
polyurethane coatings
substrate
temperature
5C
10C
20C
30C
40C
minimum
interval
36 hours
16 hours
8 hours
6 hours
4 hours
maximum
interval when
not exposed to
sunshine
6 months
6 months
6 months
4 months
3 months
maximum
interval when
exposed to
direct sunshine
3 months
3 months
3 months
2 months
2 months
surface should be dry and free from any contamination
page 3/5
SIGMACOVER 280
February 2010
Overcoating table for SigmaCover 280 for dft up to 100 m
with other types of paint like: most
chlorinated rubber-, vinyl-, alkyd
coatings
substrate
temperature
5C
10C
20C
30C
40C
minimum
interval
16 hours
10 hours
5 hours
3 hours
2 hours
maximum
interval
21 days
21 days
10 days
7 days
4 days
surface should be dry and free from any contamination
glossy finishes require a corresponding undercoat
Curing table for dft up to 100 m
substrate
temperature
touch dry
dry to handle
full cure
5C
10C
20C
30C
40C
8 hours
4 hours
2 hours
1 hour
45 min.
13 hours
6 hours
2.5 hours
1.5 hour
1 hour
21 days
14 days
7 days
5 days
3 days
adequate ventilation must be maintained during application and curing
(please refer to sheets 1433 and 1434)
Pot life (at application viscosity)
15C
20C
30C
35C
Worldwide availability
10 hours
8 hours
5 hours
4 hours
Whilst it is always the aim of PPG Protective & Marine Coatings to supply
the same product on a worldwide basis, slight modification of the product is
sometimes necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
page 4/5
SIGMACOVER 280
February 2010
REFERENCES
Explanation to product data sheets
see information sheet 1411
Safety indications
see information sheet 1430
Safety in confined spaces and health safety
Explosion hazard - toxic hazard
see information sheet 1431
Safe working in confined spaces
see information sheet 1433
Directives for ventilation practice
see information sheet 1434
Cleaning of steel and removal of rust
see information sheet 1490
PPG Protective & Marine Coatings Ballast Tank Working Procedure New
Building
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for
guidance only. All recommendations or suggestions relating to the use of the Sigma Coatings products made by PPG
Protective & Marine Coatings, whether in technical documentation, or in response to a specific enquiry, or otherwise,
are based on data which to the best of our knowledge are reliable. The products and information are designed for
users having the requisite knowledge and industrial skills and it is the end-user's responsibility to determine the
suitability of the product for its intended use.
PPG Protective & Marine Coatings has no control over either the quality or condition of the substrate, or the many
factors affecting the use and application of the product. PPG Protective & Marine Coatings does therefore not accept
any liability arising from loss, injury or damage resulting from such use or the contents of this data sheet (unless there
are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continuous product
development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this
sheet is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
179083
179085
PDS
yellow/green
redbrown
7417
4009002200 (144497 base, 142014 hardener)
6137002200 (144493 base, 142014 hardener)
page 5/5
