DRIVER CONTROLS

SECTION

DEF

DEFOGGER

CONTENTS
PRECAUTION ............................................... 3
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 3
Precaution for Procedure without Cowl Top Cover...... 3

SYSTEM DESCRIPTION .............................. 4

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT

INTELLIGENT KEY SYSTEM) .......................... 15
Diagnosis Description ..............................................15
CONSULT Function (IPDM E/R) .............................16

BCM, IPDM E/R ................................................. 19

WIRING DIAGRAM ...................................... 20

REAR WINDOW DEFOGGER SYSTEM .......... 20
Wiring Diagram ........................................................20

System Description ................................................... 6

BASIC INSPECTION ................................... 27

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM) .......................................... 7

DIAGNOSIS AND REPAIR WORK FLOW ....... 27

COMMON ITEM ........................................................... 7

COMMON ITEM : CONSULT Function (BCM COMMON ITEM) ....................................................... 7

DTC/CIRCUIT DIAGNOSIS ......................... 30

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM) ................................ 9

COMMON ITEM ........................................................... 9
COMMON ITEM : CONSULT Function (BCM COMMON ITEM) ....................................................... 9

Work Flow ................................................................27

REAR WINDOW DEFOGGER SWITCH ........... 30

Description ...............................................................30
Component Function Check ....................................30
Diagnosis Procedure ...............................................30

DEF

Description ...............................................................32
Component Function Check ....................................32
Diagnosis Procedure ...............................................32

REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT .......................... 33

Description ...............................................................33
Component Function Check ....................................33
Diagnosis Procedure ...............................................33
Component Inspection .............................................34

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM) ...............................11

DRIVER SIDE DOOR MIRROR DEFOGGER ... 35

Revision: December 2014

REAR WINDOW DEFOGGER RELAY ............. 32

REAR DEFOGGER ................................................... 10

REAR DEFOGGER : CONSULT Function (BCM REAR DEFOGGER) ............................................... 10

Diagnosis Description ............................................. 11

CONSULT Function (IPDM E/R) ............................. 12

List of ECU Reference .............................................19

Component Parts Location ........................................ 4

Component Description ............................................. 5

REAR DEFOGGER ..................................................... 8

REAR DEFOGGER : CONSULT Function (BCM REAR DEFOGGER) ................................................. 8

ECU DIAGNOSIS INFORMATION .............. 19

COMPONENT PARTS ........................................ 4

SYSTEM .............................................................. 6

Description ...............................................................35
Component Function Check ....................................35
Diagnosis Procedure ...............................................35

DEF-1

2015 Sentra NAM

Component Inspection ............................................ 36

Diagnosis Procedure ............................................... 42

PASSENGER SIDE DOOR MIRROR DEFOGGER .................................................................... 37

BOTH DOORS MIRROR DEFOGGER DONT

OPERATE BUT REAR WINDOW DEFOGGER OPERATES ............................................... 43

Description .............................................................. 37
Component Function Check ................................... 37
Diagnosis Procedure .............................................. 37
Component Inspection ............................................ 38

REAR WINDOW DEFOGGER FEEDBACK

SIGNAL .............................................................. 39

Diagnosis Procedure ............................................... 43

DRIVER SIDE DOOR MIRROR DEFOGGER

DOES NOT OPERATE. ..................................... 44
Diagnosis Procedure ............................................... 44

Description .............................................................. 39
Component Function Check ................................... 39
Diagnosis Procedure .............................................. 39

PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE. ............................ 45

SYMPTOM DIAGNOSIS ............................. 40

REAR WINDOW DEFOGGER SWITCH DOES

NOT LIGHT, BUT REAR WINDOW DEFOGGER OPERATES ............................................... 46

DEFOGGER SYSTEM SYMPTOMS ................. 40

Symptom Table ...................................................... 40

REAR WINDOW DEFOGGER AND DOOR

MIRROR DEFOGGERS DO NOT OPERATE ... 41
Diagnosis Procedure .............................................. 41

REAR WINDOW DEFOGGER DOES NOT

OPERATE BUT BOTH DOOR MIRROR DEFOGGERS OPERATE ....................................... 42

Revision: December 2014

Diagnosis Procedure ............................................... 45

Diagnosis Procedure ............................................... 46

REMOVAL AND INSTALLATION .............. 47

FILAMENT ......................................................... 47
Inspection and Repair ............................................. 47

CONDENSER .................................................... 49
Removal and Installation ......................................... 49

DEF-2

2015 Sentra NAM

PRECAUTIONS
< PRECAUTION >

PRECAUTION

PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000011539091

The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000011539092

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

DEF

M
PIIB3706J

Revision: December 2014

DEF-3

2015 Sentra NAM

COMPONENT PARTS
< SYSTEM DESCRIPTION >

SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location

INFOID:0000000011539093

ALLIA1206ZZ

1.

BCM (view with instrument panel removed)

4.

7.

IPDM E/R (rear window defogger re- 3.

lay)

A/C auto amp. (view with A/C switch

assembly removed)

A/C switch assembly (rear window de- 5.

fogger switch) (with auto A/C)

A/C switch assembly (rear window

defogger switch) (without auto A/C)

A. Rear window defogger power

connector
B. Condenser (view with rear pillar
finisher LH removed)

Rear window defogger ground connec- 8.

tor (view with rear pillar finisher RH removed)

Door mirror LH (door mirror defogger) (if equipped) (RH similar)

Revision: December 2014

2.

DEF-4

6.

2015 Sentra NAM

COMPONENT PARTS
< SYSTEM DESCRIPTION >

Component Description

INFOID:0000000011539094

Component

1:

Description

BCM

Operates the rear window defogger with the operation of rear window defogger switch.
Performs the timer control of rear window defogger.

Rear window defogger relay

Operates the rear window defogger and the door mirror defogger1 with the control signal from
BCM.

A/C auto amp

Displays the rear window defogger ON to the display when detecting the operation of the rear
window defogger.

A/C switch assembly (rear

window defogger switch)

The rear window defogger switch is turned ON.

Rear window defogger

Heats the heating wire with the power supply from the rear window defogger relay to prevent
the rear window from fogging up.

Door mirror defogger1

Heats the heating wire with the power supply from the rear window defogger relay to prevent
the door mirror from fogging up.

With heated mirrors

DEF

Revision: December 2014

DEF-5

2015 Sentra NAM

SYSTEM
< SYSTEM DESCRIPTION >

SYSTEM
System Description

INFOID:0000000011539095

SYSTEM DIAGRAM

ALLIA1209GB

OPERATION DESCRIPTION
A/C control transmits rear window defogger switch signal to A/C auto amp. when rear window defogger
switch turns ON while ignition switch is ON.
A/C auto amp. transmits rear window defogger switch signal to BCM
BCM transmits rear window defogger control signal to IPDM E/R via CAN communication.
IPDM E/R turns rear window defogger relay ON when rear window defogger control signal is received.
The power is supplied to rear window defogger and door mirror defogger* when rear window defogger relay
is ON.
When rear window defogger is activated, rear window defogger feedback signal is transmitted to A/C control
via A/C auto amp. and the indicator lamp on rear window defogger switch turns on.
*: With door mirror defogger.

TIMER FUNCTION
BCM transmits rear window defogger control signal to IPDM E/R for approximately 15 minutes when the rear
window defogger switch turns ON while ignition switch is ON. Then, IPDM E/R activates rear window defogger and door mirror defogger*.
The timer is cancelled if rear window defogger switch is pressed again during timer operation, and BCM
stops the output of rear window defogger control signal. The same action occurs during timer operation if
ignition switch is OFF.
*: With door mirror defogger.

Revision: December 2014

DEF-6

2015 Sentra NAM

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000011899931

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode

Description

ECU Identification

The BCM part number is displayed.

Self Diagnostic Result

The BCM self diagnostic results are displayed.

Data Monitor

The BCM input/output data is displayed in real time.

Active Test

The BCM activates outputs to test components.

Work support

The settings for BCM functions can be changed.

Configuration

The vehicle specification can be read and saved.

The vehicle specification can be written when replacing BCM.

CAN DIAG SUPPORT MNTR

The result of transmit/receive diagnosis of CAN communication is displayed.

SYSTEM APPLICATION

BCM can perform the following functions.

Work support

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp timer

INT LAMP

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioner

AIR CONDITIONER

Intelligent Key system

INTELLIGENT KEY

Combination switch

COMB SW

BCM

BCM

Immobilizer

IMMU

Interior room lamp battery saver

DEF

BATTERY SAVER

Trunk open

TRUNK

Vehicle security system

THEFT ALM

RAP system

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

TPMS

AIR PRESSURE MONITOR

Revision: December 2014

CAN DIAG SUPPORT MNTR

Active Test

Door lock

Configuration

Data Monitor

Sub System

Self Diagnostic Result

System

ECU Identification

Direct Diagnostic Mode

DEF-7

2015 Sentra NAM

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >

REAR DEFOGGER
REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)

INFOID:0000000011899933

DATA MONITOR
Monitor Item [Unit]

Description

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

REAR DEF SW [On/Off]

Indicates condition of rear window defogger switch.

ACTIVE TEST
Test Item
REAR DEFOGGER

Revision: December 2014

Description
This test is able to check rear window defogger operation [Off/On].

DEF-8

2015 Sentra NAM

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000011899934

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode

Description

ECU Identification

The BCM part number is displayed.

Self Diagnostic Result

The BCM self diagnostic results are displayed.

Data Monitor

The BCM input/output data is displayed in real time.

Active Test

The BCM activates outputs to test components.

Work support

The settings for BCM functions can be changed.

Configuration

The vehicle specification can be read and saved.

The vehicle specification can be written when replacing BCM.

CAN DIAG SUPPORT MNTR

The result of transmit/receive diagnosis of CAN communication is displayed.

SYSTEM APPLICATION

BCM can perform the following functions.

Work support

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp timer

INT LAMP

Remote keyless entry system

MULTI REMOTE ENT

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioner

AIR CONDITIONER

Combination switch

COMB SW

BCM

BCM

Immobilizer

IMMU

Interior room lamp battery saver

BATTERY SAVER

Trunk open

TRUNK

RAP system

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

DEF

TPMS

AIR PRESSURE MONITOR

Panic alarm system

PANIC ALARM

Revision: December 2014

CAN DIAG SUPPORT MNTR

Active Test

Door lock

Configuration

Data Monitor

Sub System

Self Diagnostic Result

System

ECU Identification

Direct Diagnostic Mode

DEF-9

2015 Sentra NAM

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >

REAR DEFOGGER
REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)

INFOID:0000000011899935

DATA MONITOR
Monitor Item [Unit]

Description

IGN ON SW [On/Off]

Indicates condition of ignition switch ON position.

ACC ON SW [On/Off]

Indicates condition of ignition switch ACC position.

REAR DEF SW [On/Off]

Indicates condition of rear window defogger switch.

RR DEF TIME [On/Off]

Indicates condition of rear window defogger switch timer.

ACTIVE TEST
Test Item
REAR DEFOGGER

Revision: December 2014

Description
This test is able to check rear window defogger operation [Off/On].

DEF-10

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

Diagnosis Description
AUTO ACTIVE TEST

Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
Front wiper (LO, HI)
Parking lamp
License plate lamp
Tail lamp
Front fog lamp (if equipped)
Headlamp (LO, HI)
A/C compressor (magnet clutch)
Cooling fan
Operation Procedure
NOTE:
Never perform auto active test in the following conditions.
Passenger door is open
CONSULT is connected
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-110,
"Component Inspection".
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation sequence

INFOID:0000000011899936

Inspection location

DEF

Operation

Front wiper

LO for 5 seconds HI for 5 seconds

10 seconds

Headlamp

LO for 10 seconds HI ON OFF 5 times

A/C compressor (magnet clutch)

ON OFF 5 times

Cooling fan

LO for 5 seconds MID for 3 seconds HI for 2 seconds

Parking lamp
License plate lamp
Tail lamp
Front fog lamp (if equipped)

Revision: December 2014

DEF-11

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >
Concept of Auto Active Test

AWMIA1509GB

IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communication. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test
Symptom

Inspection contents

Any of the following components do not operate

Parking lamp
License plate lamp
Tail lamp
Front fog lamp (if equipped)
Headlamp (HI, LO)
Front wiper (HI, LO)

Perform auto active test.

Does the applicable system operate?

Possible cause
YES

BCM signal input circuit

NO

Lamp or motor
Lamp or motor ground circuit
Harness or connector between
IPDM E/R and applicable system
IPDM E/R

YES

BCM signal input circuit

CAN communication signal between BCM and ECM
CAN communication signal between ECM and IPDM E/R

NO

Magnet clutch
Harness or connector between
IPDM E/R and magnet clutch
IPDM E/R

YES

ECM signal input circuit

CAN communication signal between ECM and IPDM E/R

NO

Cooling fan motor

Harness or connector between
IPDM E/R and cooling fan motor
IPDM E/R

Perform auto active test.

Does the magnet clutch operate?

A/C compressor does not operate

Perform auto active test.

Does the cooling fan operate?

Cooling fan does not operate

CONSULT Function (IPDM E/R)

INFOID:0000000011899937

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
Direct Diagnostic Mode

Description

Ecu Identification

The IPDM E/R part number is displayed.

Self Diagnostic Result

The IPDM E/R self diagnostic results are displayed.

Data Monitor

The IPDM E/R input/output data is displayed in real time.

Revision: December 2014

DEF-12

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >
Direct Diagnostic Mode

Description

Active Test

The IPDM E/R activates outputs to test components.

CAN Diag Support Mntr

The result of transmit/receive diagnosis of CAN communication is displayed.

ECU IDENTIFICATION

The IPDM E/R part number is displayed.

SELF DIAGNOSTIC RESULT

Refer to PCS-20, "DTC Index".

DATA MONITOR
D

Main
Signals

Description

MOTOR FAN REQ [%]

Indicates cooling fan speed signal received from ECM on CAN communication
line

AC COMP REQ [On/Off]

Indicates A/C compressor request signal received from ECM on CAN communication line

TAIL&CLR REQ [On/Off]

Indicates position light request signal received from BCM on CAN communication line

HL LO REQ [On/Off]

Indicates low beam request signal received from BCM on CAN communication
line

HL HI REQ [On/Off]

Indicates high beam request signal received from BCM on CAN communication
line

FR FOG REQ [On/Off]

Indicates front fog light request signal received from BCM on CAN communication line

FR WIP REQ [Stop/1LOW/Low/Hi]

Indicates front wiper request signal received from BCM on CAN communication
line

WIP AUTO STOP [STOP P/ACT P]

Indicates condition of front wiper auto stop signal

WIP PROT [Off/BLOCK]

Indicates condition of front wiper fail-safe operation

Monitor Item [Unit]

Indicates ignition switch ON signal received from BCM on CAN communication

line

IGN RLY1 -REQ [On/Off]

IGN RLY [On/Off]

Indicates condition of ignition relay

PUSH SW [On/Off]

Indicates condition of push-button ignition switch

INTER/NP SW [On/Off]

Indicates condition of CVT shift position

ST RLY CONT [On/Off]

Indicates starter relay status signal received from BCM on CAN communication
line

IHBT RLY -REQ [On/Off]

Indicates starter control relay signal received from BCM on CAN communication
line

ST/INHI RLY [Off/ ST /INHI]

Indicates condition of starter relay and starter control relay

DETENT SW [On/Off]

Indicates condition of CVT shift selector (park position switch)

DTRL REQ [Off]

Indicates daytime running light request signal received from BCM on CAN communication line

THFT HRN REQ [On/Off]

Indicates theft warning horn request signal received from BCM on CAN communication line

HORN CHIRP [On/Off]

Indicates horn reminder signal received from BCM on CAN communication line

ACTIVE TEST

DEF

Test item

Description

HORN

This test is able to check horn operation [On].

REAR DEFOGGER

This test is able to check rear window defogger operation [On/Off].

FRONT WIPER

This test is able to check wiper motor operation [Hi/Lo/Off].

Revision: December 2014

DEF-13

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >
Test item

Description

MOTOR FAN

This test is able to check cooling fan operation [4/3/2/1].

EXTERNAL LAMPS

This test is able to check external lamp operation [Fog/Hi/Lo/TAIL/Off].

CAN DIAG SUPPORT MNTR

Refer to LAN-13, "CAN Diagnostic Support Monitor".

Revision: December 2014

DEF-14

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)

Diagnosis Description

INFOID:0000000011899938

AUTO ACTIVE TEST

Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
Front wiper (LO, HI)
Parking lamp
License plate lamp
Tail lamp
Front fog lamp (if equipped)
Headlamp (LO, HI)
A/C compressor (magnet clutch) (if equipped)
Cooling fan

Operation Procedure
NOTE:
Never perform auto active test in the following conditions.
Passenger door is open
CONSULT is connected
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-262,
"Component Inspection".

Inspection location

Operation
LO for 5 seconds HI for 5 seconds

Front wiper

Headlamp

LO for 10 seconds HI ON OFF 5 times

A/C compressor (magnet clutch) (if equipped)

ON OFF 5 times

Cooling fan

LO for 5 seconds MID for 3 seconds HI for 2 seconds

Parking lamp
License plate lamp
Tail lamp
Front fog lamp (if equipped)

Revision: December 2014

DEF

Inspection in Auto Active Test

When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation sequence

10 seconds

DEF-15

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >
Concept of Auto Active Test

AWMIA1511GB

IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communication. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test
Symptom

Inspection contents

Any of the following components do not operate

Parking lamp
License plate lamp
Tail lamp
Front fog lamp (if equipped)
Headlamp (HI, LO)
Front wiper (HI, LO)

Perform auto active test.

Does the applicable system operate?

Possible cause
YES

BCM signal input circuit

NO

Lamp or motor
Lamp or motor ground circuit
Harness or connector between
IPDM E/R and applicable system
IPDM E/R

YES

BCM signal input circuit

CAN communication signal between BCM and ECM
CAN communication signal between ECM and IPDM E/R

NO

Magnet clutch
Harness or connector between
IPDM E/R and magnet clutch
IPDM E/R

YES

ECM signal input circuit

CAN communication signal between ECM and IPDM E/R

NO

Cooling fan motor

Harness or connector between
IPDM E/R and cooling fan motor
IPDM E/R

Perform auto active test.

Does the magnet clutch operate?

A/C compressor does not operate

Perform auto active test.

Does the cooling fan operate?

Cooling fan does not operate

CONSULT Function (IPDM E/R)

INFOID:0000000011899939

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
Direct Diagnostic Mode

Description

Ecu Identification

The IPDM E/R part number is displayed.

Self Diagnostic Result

The IPDM E/R self diagnostic results are displayed.

Data Monitor

The IPDM E/R input/output data is displayed in real time.

Revision: December 2014

DEF-16

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >
Direct Diagnostic Mode

Description

Active Test

The IPDM E/R activates outputs to test components.

CAN Diag Support Mntr

The result of transmit/receive diagnosis of CAN communication is displayed.

ECU IDENTIFICATION

The IPDM E/R part number is displayed.

SELF DIAGNOSTIC RESULT

Refer to PCS-48, "DTC Index".

DATA MONITOR
D

Main
Signals

Description

MOTOR FAN REQ [%]

Indicates cooling fan speed signal received from ECM on CAN communication
line

AC COMP REQ [On/Off]

Indicates A/C compressor request signal received from ECM on CAN communication line

TAIL&CLR REQ [On/Off]

Indicates position light request signal received from BCM on CAN communication line

HL LO REQ [On/Off]

Indicates low beam request signal received from BCM on CAN communication
line

HL HI REQ [On/Off]

Indicates high beam request signal received from BCM on CAN communication
line

FR FOG REQ [On/Off]

Indicates front fog light request signal received from BCM on CAN communication line

FR WIP REQ [Stop/1LOW/Low/Hi]

Indicates front wiper request signal received from BCM on CAN communication
line

WIP AUTO STOP [STOP P/ACT P]

Indicates condition of front wiper auto stop signal

WIP PROT [Off/BLOCK]

Indicates condition of front wiper fail-safe operation

Monitor Item [Unit]

Indicates ignition switch ON signal received from BCM on CAN communication

line

IGN RLY1 -REQ [On/Off]

IGN RLY [On/Off]

Indicates condition of ignition relay

INTER/NP SW [On/Off]

Indicates condition of CVT shift position

ST RLY CONT [On/Off]

Indicates starter relay status signal received from BCM on CAN communication
line

IHBT RLY -REQ [On/Off]

Indicates starter control relay signal received from BCM on CAN communication
line

ST/INHI RLY [Off/ ST /INHI]

Indicates condition of starter relay and starter control relay

DETENT SW [On/Off]

Indicates condition of CVT shift selector (park position switch)

DTRL REQ [Off]

Indicates daytime running light request signal received from BCM on CAN communication line

THFT HRN REQ [On/Off]

Indicates theft warning horn request signal received from BCM on CAN communication line

HORN CHIRP [On/Off]

Indicates horn reminder signal received from BCM on CAN communication line

DEF

ACTIVE TEST
Test item
HORN

This test is able to check horn operation [On].

REAR DEFOGGER

This test is able to check rear window defogger operation [On/Off].

FRONT WIPER

This test is able to check wiper motor operation [Hi/Lo/Off].

MOTOR FAN

This test is able to check cooling fan operation [4/3/2/1].

EXTERNAL LAMPS

This test is able to check external lamp operation [Fog/Hi/Lo/TAIL/Off].

Revision: December 2014

Description

DEF-17

2015 Sentra NAM

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)

< SYSTEM DESCRIPTION >
CAN DIAG SUPPORT MNTR
Refer to LAN-13, "CAN Diagnostic Support Monitor".

Revision: December 2014

DEF-18

2015 Sentra NAM

BCM, IPDM E/R

< ECU DIAGNOSIS INFORMATION >

ECU DIAGNOSIS INFORMATION

BCM, IPDM E/R

List of ECU Reference

INFOID:0000000011539104

With Intelligent Key

ECU

Reference

BCS-29, "Reference Value"

BCS-46, "Fail-safe"

BCM

BCS-48, "DTC Inspection Priority Chart"

BCS-49, "DTC Index"
PCS-13, "Reference Value"

IPDM E/R

PCS-19, "Fail-safe"
PCS-20, "DTC Index"

Without Intelligent Key

ECU

Reference
BCS-101, "Reference Value"

BCM

BCS-112, "Fail-safe"
BCS-113, "DTC Inspection Priority Chart"
BCS-113, "DTC Index"

PCS-42, "Reference Value"

IPDM E/R

PCS-47, "Fail-Safe"

PCS-48, "DTC Index"

DEF

Revision: December 2014

DEF-19

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >

WIRING DIAGRAM
REAR WINDOW DEFOGGER SYSTEM
Wiring Diagram

INFOID:0000000011539105

ABLWA3140GB

Revision: December 2014

DEF-20

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >
A

DEF

O
ABLIA5844GB

Revision: December 2014

DEF-21

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >

ABLIA7725GB

Revision: December 2014

DEF-22

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >
A

DEF

O
ABLIA5845GB

Revision: December 2014

DEF-23

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >

ABLIA7726GB

Revision: December 2014

DEF-24

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >
A

DEF

O
ABLIA5846GB

Revision: December 2014

DEF-25

2015 Sentra NAM

REAR WINDOW DEFOGGER SYSTEM

< WIRING DIAGRAM >

ABLIA5898GB

Revision: December 2014

DEF-26

2015 Sentra NAM

DIAGNOSIS AND REPAIR WORK FLOW

< BASIC INSPECTION >

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

INFOID:0000000011539106

OVERALL SEQUENCE
C

DEF

JMKIA0101GB

DETAILED FLOW
Revision: December 2014

DEF-27

2015 Sentra NAM

DIAGNOSIS AND REPAIR WORK FLOW

< BASIC INSPECTION >

1. GET INFORMATION FOR SYMPTOM

Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.

2. CHECK DTC

1. Check DTC.
2. Perform the following procedure if DTC is displayed.
Record DTC and freeze frame data (Print them out with CONSULT.)
Erase DTC.
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.

3. CONFIRM THE SYMPTOM

Confirm the symptom described by the customer.

Connect CONSULT to the vehicle in DATA MONITOR mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.

4. CONFIRM THE SYMPTOM

Confirm the symptom described by the customer.
Connect CONSULT to the vehicle in DATA MONITOR mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.

5. PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
At this time, always connect CONSULT to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-48, "DTC Inspection Priority Chart" or BCS-113,
"DTC Inspection Priority Chart" and determine trouble diagnosis order.
NOTE:
Freeze frame data is useful if the DTC is not detected.
Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure.
Is DTC detected?
YES >> GO TO 8.
NO
>> Refer to GI-40, "Intermittent Incident".

6. PERFORM BASIC INSPECTION

Perform DEF-27, "Work Flow".

>> GO TO 7

7. DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE

Detect malfunctioning system according to DEF-6, "System Description" based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 8.
Revision: December 2014

DEF-28

2015 Sentra NAM

DIAGNOSIS AND REPAIR WORK FLOW

< BASIC INSPECTION >

8. DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES >> GO TO 9.
NO
>> Check voltage of related BCM terminals using CONSULT.

9. REPAIR OR REPLACE THE MALFUNCTIONING PART

1.
2.
3.

Repair or replace the malfunctioning part.

Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replacement.
Check DTC. If DTC is displayed, erase it.

>> GO TO 10.

10. FINAL CHECK

When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO
>> Inspection End.

DEF

Revision: December 2014

DEF-29

2015 Sentra NAM

REAR WINDOW DEFOGGER SWITCH

< DTC/CIRCUIT DIAGNOSIS >

DTC/CIRCUIT DIAGNOSIS
REAR WINDOW DEFOGGER SWITCH
Description

INFOID:0000000011539107

The rear window defogger is operated by pressing the rear window defogger switch ON.
The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.

Component Function Check

INFOID:0000000011539108

1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

1.
2.

Check (REAR DEF SW) in BCM - REAR DEFOGGER DATA MONITOR mode by using CONSULT.
Operate rear window defogger switch and check the status on CONSULT screen.
Monitor Item

Condition
Rear window defogger
switch

REAR DEF SW

status

Pressed

On

Released

Off

Is the inspection result normal?

YES >> Rear window defogger switch function is OK.
NO
>> Refer to DEF-30, "Diagnosis Procedure".

Diagnosis Procedure

INFOID:0000000011539109

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

1. CHECK REAR WINDOW DEFOGGER ON SIGNAL CIRCUIT

1.
2.
3.

Turn ignition switch to ON.

Turn rear window defogger switch ON.
Check voltage between BCM connector and ground.
With Intelligent Key

(+)
BCM

()

Connector

Terminal

M84

15

Ground

Voltage (V)
(Approx.)

Condition

Rear window defogger

switch

Released

JPMIA0012GB

1.0 - 1.5 V
Depressed

0V

Without Intelligent Key

(+)
BCM

()

Connector

Terminal

M21

10

Ground

Voltage (V)
(Approx.)

Condition

Rear window defogger

switch

ON

OFF

Battery voltage

Is the inspection result normal?

Revision: December 2014

DEF-30

2015 Sentra NAM

REAR WINDOW DEFOGGER SWITCH

< DTC/CIRCUIT DIAGNOSIS >
YES >> Replace BCM. Refer to BCS-76, "Removal and Installation" (with Intelligent Key system) or BCS133, "Removal and Installation" (without Intelligent Key system).
NO
>> GO TO 2.

2. CHECK HARNESS CONTINUITY

1.
2.
3.

Turn ignition switch to OFF.

Disconnect BCM and A/C auto amp.
Check continuity between BCM connector and A/C auto amp.

C
BCM
Connector

A/C auto amp.

Terminal

M21 (without Intelligent Key)

10

M84 (with Intelligent Key)

4.

15

Connector

Terminal

Continuity

M29 (without A/C)

M33 (with manual A/C)
M33 (with manual A/C)

16

Yes

M34 (with auto A/C)

Check continuity between BCM harness connector and ground.

BCM
Connector

Terminal

M21 (without Intelligent Key)

10

M84 (with Intelligent Key)

15

Continuity

Ground
No

Is the inspection result normal?

YES >> Replace A/C auto amp. Refer to HAC-105, "Removal and Installation" (with auto A/C) or HAC189, "Removal and Installation" (without auto A/C).
NO
>> Repair or replace harness.

DEF

Revision: December 2014

DEF-31

2015 Sentra NAM

REAR WINDOW DEFOGGER RELAY

< DTC/CIRCUIT DIAGNOSIS >

REAR WINDOW DEFOGGER RELAY

Description

INFOID:0000000011539110

Power is supplied to the rear window defogger with BCM control.

Component Function Check

INFOID:0000000011539111

1. CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT

1.
2.

Turn ignition switch ON.

Check that an operation noise of rear window defogger relay (located in IPDM E/R) can be heard when
turning the rear window defogger switch ON.
Is the inspection result normal?
YES >> Rear window defogger relay power supply circuit is OK.
NO
>> Refer to DEF-32, "Diagnosis Procedure".

Diagnosis Procedure

INFOID:0000000011539112

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

1.CHECK FUSES
Check if any of the following fuses in the IPDM E/R are blown.
COMPONENT PARTS

AMPERE

IPDM E/R

15A

FUSE NO.
31
32

Is the inspection result normal?

YES >> GO TO 2
NO
>> Replace the fuse after repairing the affected circuit.

2. CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT

1.
2.

Turn ignition switch ON.

Check voltage between IPDM E/R connector E48 terminal 62 and ground.
Terminals
(+)

IPDM E/R connector

Terminal

E48

62

()

Condition of rear
window defogger
switch

Voltage (V)
(Approx.)

ON

Battery voltage

OFF

0V

Ground

Is the inspection result normal?

YES >> GO TO 3
NO
>> Replace IPDM E/R. Refer to PCS-31, "Removal and Installation" (with Intelligent Key system) or
PCS-60, "Removal and Installation" (without Intelligent Key system).

3. CHECK INTERMITTENT INCIDENT

Check intermittent incident.

Refer to GI-40, "Intermittent Incident"
Is the inspection result normal?
YES >> Check the following:
Battery power supply circuit.
IPDM E/R.
NO
>> Repair or replace the malfunctioning parts.
Revision: December 2014

DEF-32

2015 Sentra NAM

REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

< DTC/CIRCUIT DIAGNOSIS >

REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

Description

INFOID:0000000011539113

Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.

Component Function Check

INFOID:0000000011539114

1. CHECK REAR WINDOW DEFOGGER

Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch
ON.
Is the inspection result normal?
YES >> Rear window defogger is OK.
NO
>> Refer to DEF-33, "Diagnosis Procedure".

Diagnosis Procedure

INFOID:0000000011539115

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

AMPERE

FUSE NO.

31

15A

32

Is the inspection result normal?

YES >> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit.

2. CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT

1.
2.

Check if any of the following fuses in IPDM E/R are blown.

IPDM E/R

1. CHECK FUSES
COMPONENT PARTS

Turn ignition switch ON.

Check voltage between IPDM E/R connector and ground.

DEF

(+)
IPDM E/R

()

Connector

Terminal

E48

62

Ground

Voltage (V)
(Approx.)

Condition

Rear window defogger switch

ON

Battery voltage

OFF

Is the inspection result normal?

YES >> GO TO 3.
NO
>> Perform rear window defogger relay diagnosis. Refer to DEF-32, "Diagnosis Procedure".

3. CHECK POWER SUPPLY CIRCUIT

1.
2.

Turn ignition switch ON.

Check voltage between rear window defogger connector and ground.

Revision: December 2014

DEF-33

2015 Sentra NAM

REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

< DTC/CIRCUIT DIAGNOSIS >
(+)
Rear window defogger
Connector

Terminal

B62

()

Voltage (V)
(Approx.)

Condition

Ground

Rear window defogger switch

ON

Battery voltage

OFF

Is the inspection result normal?

YES >> GO TO 4.
NO
>> GO TO 5.

4. CHECK GROUND CIRCUIT

1.
2.
3.

Turn ignition switch OFF.

Disconnect rear window defogger.
Check continuity between rear window defogger connector and ground.
Rear window defogger
Connector

Terminal

B63

Continuity

Ground

Yes

Is the inspection result normal?

YES >> GO TO 6.
NO
>> Repair or replace harness.

5. CHECK HARNESS CONTINUITY

1.
2.
3.

Turn ignition switch OFF.

Disconnect IPDM E/R.
Check continuity between IPDM E/R connector and condenser connector.
IPDM E/R

Condenser

Connector

Terminal

Connector

Terminal

E48

62

B50

Continuity
Yes

Is the inspection result normal?

YES >> Replace condenser. Refer to DEF-49, "Removal and Installation".
NO
>> Replace or repair harness.

6. CHECK FILAMENT

Check filament.
Refer to DEF-34, "Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-40, "Intermittent Incident".
NO
>> Repair filament. Refer to DEF-47, "Inspection and Repair".

Component Inspection

INFOID:0000000011539116

1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-47, "Inspection and Repair".
Is the inspection result normal?
YES >> Inspection End.
NO
>> Repair filament. Refer to DEF-47, "Inspection and Repair".

Revision: December 2014

DEF-34

2015 Sentra NAM

DRIVER SIDE DOOR MIRROR DEFOGGER

< DTC/CIRCUIT DIAGNOSIS >

DRIVER SIDE DOOR MIRROR DEFOGGER

Description

INFOID:0000000011539117

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.

Component Function Check

INFOID:0000000011539118

1. CHECK DOOR MIRROR DEFOGGER LH

Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch
ON.
Is the inspection result normal?
YES >> Door mirror defogger is OK.
NO
>> Refer to DEF-35, "Diagnosis Procedure".

Diagnosis Procedure

INFOID:0000000011539119

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

G

1. CHECK POWER SUPPLY CIRCUIT

1.
2.
3.
4.

Turn ignition switch OFF.

Disconnect door mirror LH.
Turn ignition switch ON.
Check voltage between door mirror LH connector and ground.

(+)
Door mirror LH

()

Connector

Terminal

D7

Ground

Voltage (V)
(Approx.)

Condition

Rear window defogger switch

ON

Battery voltage

OFF

Is the inspection result normal?

YES >> GO TO 2.
NO
>> Repair or replace harness.

DEF

2. CHECK GROUND CIRCUIT

1.
2.

Turn ignition switch OFF.

Check continuity between door mirror LH connector and ground.
Door mirror LH
Connector

Terminal

D7

Ground

Continuity
Yes

Is the inspection result normal?

YES >> GO TO 3.
NO
>> Repair or replace harness.

3. CHECK DOOR MIRROR DEFOGGER LH

Check door mirror defogger LH.
Refer to DEF-36, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Replace door mirror. Refer to MIR-18, "DOOR MIRROR ASSEMBLY : Removal and Installation".
Revision: December 2014

DEF-35

2015 Sentra NAM

DRIVER SIDE DOOR MIRROR DEFOGGER

< DTC/CIRCUIT DIAGNOSIS >

4. CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to GI-40, "Intermittent Incident".
Is the inspection result normal?
YES >> Check the following.
Battery power supply circuit.
Fuse block (J/B).
NO
>> Repair or replace the malfunctioning parts.

Component Inspection

INFOID:0000000011539120

1. CHECK DOOR MIRROR DEFOGGER LH

1.
2.
3.

Turn ignition switch OFF.

Disconnect door mirror LH.
Check continuity between door mirror terminals.
Terminal
3

Continuity
9

Yes

Is the inspection result normal?

YES >> Inspection End.
NO
>> Replace door mirror LH. Refer to MIR-18, "DOOR MIRROR ASSEMBLY : Removal and Installation".

Revision: December 2014

DEF-36

2015 Sentra NAM

PASSENGER SIDE DOOR MIRROR DEFOGGER

< DTC/CIRCUIT DIAGNOSIS >

PASSENGER SIDE DOOR MIRROR DEFOGGER

Description

INFOID:0000000011539121

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.

Component Function Check

INFOID:0000000011539122

1.CHECK DOOR MIRROR DEFOGGER RH

Check that the heating wire of door mirror defogger RH is heated when turning the rear window defogger
switch ON.
Is the inspection result normal?
YES >> Door mirror defogger RH is OK.
NO
>> Refer to DEF-37, "Diagnosis Procedure".

Diagnosis Procedure

INFOID:0000000011539123

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

G

1. CHECK POWER SUPPLY CIRCUIT

1.
2.
3.
4.

Turn ignition switch OFF.

Disconnect door mirror RH.
Turn ignition switch ON.
Check voltage between door mirror RH connector and ground.

(+)
Door mirror RH

()

Connector

Terminal

D106

Ground

Voltage (V)
(Approx.)

Condition

Rear window defogger switch

ON

Battery voltage

OFF

Is the inspection result normal?

YES >> GO TO 2.
NO
>> Repair or replace harness.

DEF

2. CHECK GROUND CIRCUIT

1.
2.

Turn ignition switch OFF.

Check continuity between door mirror RH connector and ground.
Door mirror RH
Connector

Terminal

D106

Ground

Continuity
Yes

Is the inspection result normal?

YES >> GO TO 3.
NO
>> Repair or replace harness.

3. CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

Check door mirror defogger RH.
Refer to DEF-38, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.

Revision: December 2014

DEF-37

2015 Sentra NAM

PASSENGER SIDE DOOR MIRROR DEFOGGER

< DTC/CIRCUIT DIAGNOSIS >
NO
>> Replace door mirror RH. Refer to MIR-18, "DOOR MIRROR ASSEMBLY : Removal and Installation".

4. CHECK INTERMITTENT INCIDENT

Check intermittent incident.

Refer to GI-40, "Intermittent Incident".
Is the inspection result normal?
YES >> Check the following.
Battery power supply circuit.
Fuse block (J/B).
NO
>> Repair or replace the malfunctioning parts.

Component Inspection

INFOID:0000000011539124

1. CHECK DOOR MIRROR DEFOGGER RH

1.
2.
3.

Turn ignition switch OFF.

Disconnect door mirror RH.
Check continuity between door mirror terminals.
Terminal
3

Continuity
9

Yes

Is the inspection result normal?

YES >> Inspection End.
NO
>> Replace door mirror RH. Refer to MIR-18, "DOOR MIRROR ASSEMBLY : Removal and Installation".

Revision: December 2014

DEF-38

2015 Sentra NAM

REAR WINDOW DEFOGGER FEEDBACK SIGNAL

< DTC/CIRCUIT DIAGNOSIS >

REAR WINDOW DEFOGGER FEEDBACK SIGNAL

Description

INFOID:0000000011539125

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.

Component Function Check

INFOID:0000000011539126

1.CHECK REAR WINDOW DEFOGGER FEEDBACK SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window
defogger switch ON.
Is the inspection result normal?
OK
>> Rear window defogger feedback signal is OK.
NG
>> Refer to DEF-39, "Diagnosis Procedure".

Diagnosis Procedure

INFOID:0000000011539127

1.CHECK REAR WINDOW DEFOGGER FEEDBACK SIGNAL

1.
2.
3.

Turn ignition switch ON.

Turn rear window defogger switch ON.
Check voltage between A/C auto amp. harness connector and ground.
A/C auto amp.
Connector
M29 (without A/C)
M33 (with manual A/C)

Ground
25

Voltage (V)
(Approx.)

Condition

Terminal

Rear window defogger switch

M34 (with auto A/C)

ON

Battery voltage

OFF

Is the inspection result normal?

YES >> Replace A/C auto amp. Refer to HAC-105, "Removal and Installation" (with auto A/C) or HAC189, "Removal and Installation" (without auto A/C).
NO
>> Repair or replace harness.

DEF

Revision: December 2014

DEF-39

2015 Sentra NAM

DEFOGGER SYSTEM SYMPTOMS

< SYMPTOM DIAGNOSIS >

SYMPTOM DIAGNOSIS
DEFOGGER SYSTEM SYMPTOMS
Symptom Table

INFOID:0000000011539128

Symptom

Reference page

Rear window defogger and door mirror defoggers* do not operate.

Refer to DEF-41, "Diagnosis Procedure".

Rear window defogger does not operate but both door mirror defoggers* operate.

Refer to DEF-42, "Diagnosis Procedure".

Both door mirror defoggers* dont operate but rear window defogger operates.

Refer to DEF-43, "Diagnosis Procedure".

Driver side door mirror defogger* does not operate.

Refer to DEF-44, "Diagnosis Procedure".

Passenger side door mirror defogger* does not operate.

Refer to DEF-45, "Diagnosis Procedure".

Rear window defogger switch does not light, but rear window defogger operates.

Refer to DEF-46, "Diagnosis Procedure".

*: if equipped

Revision: December 2014

DEF-40

2015 Sentra NAM

REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGERS DO NOT OPERATE

< SYMPTOM DIAGNOSIS >

REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGERS DO NOT

OPERATE
Diagnosis Procedure

INFOID:0000000011539129

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

1. CHECK REAR WINDOW DEFOGGER SWITCH

Check rear window defogger switch.

Refer to DEF-30, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.

2. CHECK REAR WINDOW DEFOGGER RELAY

Check rear window defogger relay.

Refer to DEF-32, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 3 .
NO
>> Repair or replace the malfunctioning parts.

3. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

Check rear window defogger power supply and ground circuit.

Refer to DEF-33, "Component Function Check".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.

DEF

Revision: December 2014

DEF-41

2015 Sentra NAM

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR MIRROR
DEFOGGERS OPERATE
< SYMPTOM DIAGNOSIS >

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR

MIRROR DEFOGGERS OPERATE
Diagnosis Procedure

INFOID:0000000011539130

1. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

Check rear window defogger power supply and ground circuit.
Refer to DEF-33, "Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-40, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.

Revision: December 2014

DEF-42

2015 Sentra NAM

BOTH DOORS MIRROR DEFOGGER DONT OPERATE BUT REAR WINDOW

DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >

BOTH DOORS MIRROR DEFOGGER DONT OPERATE BUT REAR WINDOW DEFOGGER OPERATES
Diagnosis Procedure

INFOID:0000000011539131

Regarding Wiring Diagram information, refer to DEF-20, "Wiring Diagram".

1. CHECK DOOR MIRROR DEFOGGER FUSE

Check if the following fuse in fuse block (J/B) is blown.

COMPONENT PARTS

AMPERE

FUSE NO.

Fuse block (J/B)

10A

Is the inspection result normal?

YES >> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit.

2. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT

Check door mirror defogger power supply and ground circuit.
Refer to DEF-35, "Component Function Check" (driver side) or DEF-37, "Component Function Check" (passenger side).
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.

3. CHECK BOTH DOOR MIRROR DEFOGGER

1. Check door mirror LH. Refer to DEF-36, "Component Inspection".

2. Check door mirror RH. Refer to DEF-38, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.

DEF

Revision: December 2014

DEF-43

2015 Sentra NAM

DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.

< SYMPTOM DIAGNOSIS >

DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.

Diagnosis Procedure

INFOID:0000000011539132

1. CHECK DOOR MIRROR DEFOGGER LH

Check door mirror defogger LH.
Refer to DEF-35, "Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-40, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.

Revision: December 2014

DEF-44

2015 Sentra NAM

PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.

< SYMPTOM DIAGNOSIS >

PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.

Diagnosis Procedure

INFOID:0000000011539133

1. CHECK DOOR MIRROR DEFOGGER RH

Check door mirror defogger RH.

Refer to DEF-37, "Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-40, "Intermittent Incident".
NO
>> Repair or replace the malfunctioning parts.

DEF

Revision: December 2014

DEF-45

2015 Sentra NAM

REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >

REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW DEFOGGER OPERATES
Diagnosis Procedure

INFOID:0000000011539134

1. CHECK REAR WINDOW DEFOGGER SWITCH

Check that the rear window defogger switch is operating normally.
Is the inspection result normal?
YES >> Refer to GI-40, "Intermittent Incident".
NO
>> Refer to DEF-39, "Diagnosis Procedure".

Revision: December 2014

DEF-46

2015 Sentra NAM

FILAMENT
< REMOVAL AND INSTALLATION >

REMOVAL AND INSTALLATION

FILAMENT
Inspection and Repair

INFOID:0000000011539135

INSPECTION
1.

When measuring voltage, wrap tin foil around the top of the negative probe. Then press the foil against the wire with your finger.

SEL122R

2.

Attach probe circuit tester (in Volt range) to middle portion of

each filament.

I
SEL263

3.
4.

If a filament is burned out, circuit tester registers 0 or battery

voltage.
To locate burned out point, move probe to left and right along filament. Test needle will swing abruptly when probe passes the
point.

DEF

SEL265

REPAIR
REPAIR EQUIPMENT
Conductive silver composition (Dupont No. 4817 or equivalent)

Revision: December 2014

DEF-47

2015 Sentra NAM

FILAMENT
< REMOVAL AND INSTALLATION >
Ruler 30 cm (11.8 in) long
Drawing pen
Heat gun
Alcohol
Cloth
REPAIRING PROCEDURE

1.
2.

3.

Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
Apply a small amount of conductive silver composition to tip of
drawing pen.
NOTE:
Shake silver composition container before use.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
PIIA0215E

4.

After repair has been completed, check repaired wire for continuity. This check should be conducted 10 minutes after silver
composition is deposited.
CAUTION:
Do not touch repaired area while test is being conducted.

SEL012D

5.

Apply a constant stream of hot air directly to the repaired area

for approximately 20 minutes with a heat gun. A minimum distance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
NOTE:
If a heat gun is not available, let the repaired area dry for 24
hours.

SEL013D

Revision: December 2014

DEF-48

2015 Sentra NAM

CONDENSER
< REMOVAL AND INSTALLATION >

CONDENSER

Removal and Installation

INFOID:0000000011539136

REMOVAL
1.
2.

Remove the rear pillar finisher. Refer to INT-29, "REAR PILLAR FINISHER : Removal and Installation".
Disconnect the harness connectors (1), remove the condenser
bolt (A) and the condenser (2).
: Front

ALLIA1183ZZ

INSTALLATION
Installation is in the reverse order of removal.

DEF

Revision: December 2014

DEF-49

2015 Sentra NAM