Tsurumi

TRN

400V
50Hz

Submersible aerator

Auto-suction submersible aerator for communal and

industrial waste water clearance and treatment.

TRN-submersible aerator
The Tsurumi TRN-submersible aerator is a
submersible motor, mixer and compressor in
one unit. The rotor of the submersible aerator
is directly connected with the motor shaft. As
shown in the illustration below, the rotation of
the rotor causes a circular movement of the
water, creating negative pressure around the
rotor. Air is then automatically suctioned from
above through the suction line. At the same
time water flows in from below into the area
around the rotor - this is then intensively

mixed with air due to the rotation of the rotor.

A fine air-water mixture is formed that is spun
radially outwards at high speeds through the
channels of the guide ring. The flow that this
creates ensures that every part of the tank is
reached and that the water is uniformly
oxygenated.

Features
High oxygen intake
optimum distribution and high
oxygen yield thanks to high level
of microscopic, small air bubbles.

Perfect mixing within the tank

a strong flow of water mixed with air
ensures
that every part of the tank is aerated
and that no sediment is formed.

Submersible motor

Simple, robust and compact

Flow generated by
air bubbles

The bearings and the oil bath around the

shaft seal are larger than required.
The air suctioned from above presses the
water away from the rotor and forms an
air cushion, preventing the
shaft seal from touching water.
This ensures fault-free 24 hour operation and
ensures long product life.

Water and air

are mixed here

Air

Suction
pipe
Rotor

Flow generated by
centrifuged water
Water
Guide vane

FLOW SAMPLE
round tank

Ratio of tank length to width:

1:1.5 or less

square tank

Ratio of tank length to width: 1:2

rectangular tank

ADVANTAGES
- thorough mixing of the
waste water, thereby preventing
sediments
- tiny air bubbles provide aeration with
high oxygen utilisation
- completely insensitive to frost
- low noise level
- no spray formed
- simple installation and servicing thanks
to simple construction
- low risk of blockage

To prevent blockage caused by fibres

and solid particles the. TRN-series has
a special rotor and a specially designed
suction plate.

- large oil chamber

- Casing made of solid cast iron
- Shaft seal is protected from water
during operation
- A proven track record, with
tens of thousands produced
over more than 20 years

Uses in waste water clearance and treatment are as follows:

Mixing and equaliser tanks:
Standardising of waste water sludge loads and quantities and preventing odours
developing
SBR reactions and sludge activation tanks:
Breakdown of organic substances
Sludge stabilisation: Preventing development of odour and further oxidation of
the organic components in the waste water
Neutralisation:
Neutralisation or alkaline waste water with fumes or CO2
Flotation:
Flotation of oils and greases
Pond aeration:
Improves the aeration in natural waters such as in eutrophication
3

Standard accessories:
Sound absorber and valve

The open rotor of the TRN series suctions a large volume of water for the motor power through
the pump basket. This water is then mixed with air and distributed horizontally in all directions
through the channels of the guide ring.
The top of the rotor is hollow and allows the air that has been suctioned in to fill the area around
the shaft seal so that it can mix with the water at the rotor. One consequence of this is that a
layer of air is formed separating the shaft seal from the medium and thereby substantially
increasing the life of the shaft seal. Another effect is that the water that is suctioned in is
oxygenated with tiny air bubbles, effectively aerating the waste water.
To prevent blockage caused by fibres and solid particles the TRN series has a special rotor and a specially designed
suction plate.
The long life and low maintenance of the TRN submersible aerator is due specifically to the specially selected
materials. Only cast iron comes into contact with the water. Parts that are subject to particular wear such as the
shaft, screws, the rotor and suction plates are made of stainless steel. The dual mechanical seal (SiC/SiC) is a
particular feature of the TRN aerator; this is cooled by an oil bath of at least 0.5l per kW motor output.

Model

Motor
output
kW

32TRN2.75
32TRN21.5
50TRN42.2
50TRN43.7
50TRN45.5
80TRN47.5
80TRN412
80TRN417
100TRN424
150TRN440

0,75
1,5
2,2
3,7
5,5
7,5
12
17
24
40

Nominal Phases
current
A

2,4
3,5
5,3
8,6
12,1
15,9
25,7
35,2
48,0
83,0

3
3
3
3
3
3
3
3
3
3

Rpm

Start
method

2850
2850
1450
1450
1450
1450
1450
1450
1450
1450

direct
direct
direct
direct
direct
direct
s.-d.
s.-d.
s.-d.
s.-d.

Diameter
Air
Sound
Airpipe max. rotor Number
depth m Outlets volume emissions
mm
3
m /h
db-A

32
32
50
50
50
80
80
80
100
150

3.5
3.5
3.6
4.0
4.0
4.5
6.0
6.0
6.0
6.0

m
m
m
m
m
m
m
m
m
m

6
6
6
6
6
6
6
6
8
8

7
20
39
55
78
124
157
202
388
528

54
58
61
70
70
68
73
72
74
74

Dry
weight
kg

Cable
length
m

55
55
140
150
170
190
200
220
460
635

10
10
10
10
10
10
10
20
20
20

* Dry weight of the pump without cables

* Sound emissions measured at max. installation depth at 1m distance from the sound absorber (mean of four measurements)
* Air volume and oxygen intake rate measured at max. installation depth (for motor output of 12kW or over: at 5m)

Flow picture:

Model
Subsidiary flow
Primary flow:

Main flow:
direct oxygen intake thanks to air
bubbles
Subsidiary flow:
indirect oxygen intake by mixing

mixing by
centrifuged water

mixing by rising air

bubbles

32TRN2.75
32TRN21.5
50TRN42.2
50TRN43.7
50TRN45.5
80TRN47.5
80TRN412
80TRN417
100TRN424
150TRN440

Guide ring
Depth

3.5
3.5
3.6
4.0
4.0
4.5
6.0
6.0
6.0
6.0

m
m
m
m
m
m
m
m
m
m

Cross
section
Primary
flow

1.4
1.8
2.4
3.0
3.8
4.4
5.2
5.6
6.3
7.3

m
m
m
m
m
m
m
m
m
m

Cross section Cross section

Subsidiary
Subsidiary
flow
flow
Round tank Square tank

3.5 m
4.5 m
6.0 m
7.0 m
9.0 m
10.0 m
12.0 m
13.0 m
14.5 m
17.0 m

3.0 m
4.0 m
5.5 m
6.5 m
8.0 m
9.0 m
11.0 m
11.5 m
13.0 m
15.0 m

Primary and subsidiary flow measured at max. installation depth

The motor is a conventional squirrel cage motor with the following

features:
The bearings are over-sized (see illustrations on pages 11 and 12).
The stripped cable ends in the packing box are sealed in synthetic resin so as to
prevent water from penetrating the motor.
The directly started motors have a thermoswitch (motor protection) that
resets automatically. Within the cable wraps star delta motors have
a thermoswitch for each phase.
The double end face seal (SiC/SiC) is lubricated and cooled by an oil bath,
that is much larger than in other pumps with a comparable motor performance.

Installation types:
The free-standing installation is the most common type of installation. The submersible aerator is placed on the
floor of the tank without further anchorage. Its weight prevents the device from moving. The submersible aerator can
be lifted out of the tank with a crane for servicing without having to empty the tank.
For free-standing installation a simple metal stand can be used to increase the maximum tank depth in which the
submersible aerator can be installed by 0.5m without primary
pressure.
The inlet opening can also be extended with a pipe; the water
is taken from close to the base and the air above is centrifuged.
This allows the maximum tank depth to be increased by max.
1.5m.
Stationary installation is generally used for fitting in deep
tanks (also in combination with aeration with primary pressure,
etc.) or if assembly or disassembly is not possible with a mobile
crane. In this case the submersible aerators are fitted between guide pipes or on a
bridge. Lifting equipment is required to lift it out of the tank.
Floating installation is used, for instance, to aerate unsecured tanks, ponds, lakes
or rivers. The submersible aerator can also be secured oscillating on ropes or can be firmly anchored in position.
Hanging installation with suitable floats is also an option. A mobile crane is generally used to lift it in and out of the
tank.

Air volume - water depth - curve

Air volume m3/h

in clear water under normal conditions the air volume can deviate 5%

Air volume m3/h

Water depth m

Water depth m

AERATION UNDER PRE-APPLIED PRESSURE:

The aeration system consists of a compressor and a TRN-series TSURUMI submersible aerator.
A tank, for example is 9m, with 6m for the primary pressure of the compactor and 3m for the aerator.
This system substantially reduces the necessary power input and consumption and requires much less space.
The oxygen transfer rate is also increased thanks to the higher potential installation depth. This increases the time
the air bubbles take to reach the surface of the water in the aeration tanks.

Primary pressure of the

compactor
Pressure
of the
aerator

overall submersion depth

Compactor

Aerator

EXAMPLES OF ACTIVATED SLUDGE PROCESS

Contact activated sludge process
Sludge
absorption
equipment

Control
tank

Disinfection tank
Fine rake

Influx
Outflow
Rake

Redirecting tank
with rake

Waste tank

Flotation tank

Equaliser tank
(primary
aeration)

Contact activated sludge tank

Defoaming pump

Replacement pump
Stand-by pump
Pump operational

Sludge thickening

Sludge deposit tank

Extended activated sludge process

Control tank for sludge return
Sludge return

Control tank

Sludge
absorption
equipment

Rake

Disinfection tank
Fine rake
Influx

Outflow

Sieve/rake
Rake

Waste tank
Defoaming pump

Sludge activation tank

Equaliser tank
(primary
aeration)

Primary
clarification
tank
(primary
aeration)

Flotation tank
Pump operational
Stand-by pump
Replacement
pump

Redirecting tank
with rake

Sludge deposit tank

Sludge thickening

Conventional activated sludge process

Control tank for sludge return
Sand container

Control tank

Rake

Disinfection tank
Sludge return

Fine rake

Sludge
absorption
equipment

Influx

Outflow

Sieve/rake
Inflow
via rake
Grit trap

Primary
clarification
tank
(primary
aeration)

Waste tank
Equalising reservoir
(primary aeration)

Sludge activation tank

Replacement pump
Stand-by pump
Pump operational
Sludge thickening
Sludge deposit tank

Flotation tank

Defoaming pump

INSTALLATION EXAMPLE 32TRN2.75

INSTALLATION EXAMPLE 80TRN417

DIMENSIONS

in mm

32TRN2.75 / 32TRN21.5
Silencer and valve

50TRN42.2 / 50TRN43.7

Air pipe
32
50
80
100
150

A
180
230
245
345
448

B
C
D
116 275
154 370
180
585
256
760
370 740 863
Values in ( ) for 50TRN43.7

80TRN47.5 / 80TRN412

50TRN45.5

Values in ( ) for 80TRN412

100TRN424

80TRN417

150TRN440

10

COMPONENTS AND MATERIAL

50TRN42.2

32TRN2.75 / 32TRN21.5

No.
1
18
19
21
22
25
26A
26B
30
35
36
48

NAME
Cable
Air Passage
Guide Vane
Rotor
Suction Cover
Mechanical Seal
Spacer
Oil seal
Oil Lifter
Oil Plug
Lubricant
Threaded Flange

MATERIAL
H07RN-F
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
Silicon Carbide
Carbon Steel
Nitrile Rubber
Plastic
EN-X5CrNi18-10
ISO VG32
EN-GJL-200

No.
52A
52B
53
54
55
56
60
64
72

NAME
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Eye Bolt

No.
1
18
19
21
22
25
26A
26B
28
30
35
36

MATERIAL

EN-X30Cr13

EN-GJL-150
EN-GJL-150
EN-X5CrNi18-10

NAME
Cable
Air Passage
Guide Vane
Rotor
Suction Cover
Mechanical Seal
Spacer
Oil Seal
Middle Plate
Oil Lifter
Oil Plug
Lubricant

MATERIAL
H07RN-F
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
Silicon Carbide
Carbon Steel
Nitrile Rubber
EN-X12Cr13
Plastic
EN-X5CrNi18-10
ISO VG32

50TRN43.7

No.
1
18
19
21
22
25
26A
26B
28
30
35
36

NAME
Cable
Air Passage
Guide Vane
Rotor
Suction Coaver
Mechanical Seal
Spacer
Oil Seal
Middle Cover
Oil Lifter
Oil Plug
Lubricant

No.
48
52A
52B
53
54
55
56
60
64
72

NAME
Threaded Flange
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Eye Bolt

MATERIAL
EN-GJL-200

EN-X30Cr13

EN-GJL-150
EN-GJL-150
EN-X5CrNi18-10

50TRN45.5 / 80TRN47.5

MATERIAL
H07RN-F
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
Silicon Carbide
Carbon Steel
Nitrile Rubber
EN-X12Cr13
Plastic
EN-X5CrNi18-10
ISO VG32

No.
48
52A
52B
53
54
55
56
60
64
72

NAME
Threaded Flange
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Eye Bolt

No.
1
6
18
19
21
22
25
26A
26B
28
30
35

MATERIAL
EN-GJL-200

EN-X30Cr13

EN-GJL-150
EN-GJL-150
EN-X5CrNi18-10

11

NAME
Cable
Stuffing Box
Air Passage
Guide Vane
Rotor
Suction Cover
Mechanical Seal
Spacer
Oil Seal
Middle Plate
Oil Lifter
Oil Plug

MATERIAL
H07RN-F
EN-GJL-150
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
Silicon Carbide
Carbon Steel
Nitrile Rubber
EN-X12Cr13
Plastic
EN-X5CrNi18-10

No.
36
48
50
52A
52B
53
54
55
56
60
64
72

NAME
Lubricant
Threaded Flange
Motor Bracket
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Eye Bolt

MATERIAL
ISO VG32
EN-GJL-200
EN-GJL-200

EN-X30Cr13

EN-GJL-150
EN-GJL-200
EN-X5CrNi18-10

80TRN412 / 80TRN417

No.
1
6
18
19
21
22
25
26A
26B
28
30
35

NAME
Cable
Stuffing Box
Air Passage
Guide Vane
Impeller
Suction Cover
Mechanical Seal
Spacer
Oil Seal
Middle Plate
Oil Lifter
Oil Plug

MATERIAL
H07RN-F
EN-GJL-150
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
Silicon Carbide
Carbon Steel
Nitrile Rubber
EN-X12Cr13 EN-GX12Cr12
Plastic
EN-X5CrNi18-10

No.
36
48
50
52A
52B
53
54
55
56
60
64
72

NAME
Lubricant
Threaded Flange
Motor Bracket
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Eye bolt

100TRN424

MATERIAL
ISO VG32
EN-GJL-200
EN-GJL-200

EN-X30Cr13

EN-GJL-150
EN-GJL-200
EN-X5CrNi18-10

No.
1
6
18
19
21
22
23
25
26A
26B
28
30
35

NAME
Cable
Stuffing Box
Air Passage
Guide Vane
Rotor
Suction Cover
Strainer
Mechanical Seal
Spacer
Oil Seal
Middle Plate
Oil Lifter
Oil Plug

MATERIAL
H07RN-F
EN-GJL-150
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
DIN 1.0040+EN-X5CrNi18-10
Silicon Carbide
DIN 1.0040
Nitrile Rubber
EN-GX12Cr12
Plastic
EN-X5CrNi18-10

No.
36
48
50
52A
52B
53
54
55
56
60
64
72

NAME
Lubricant
Threaded Flange
Motor Bracket
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Eye Bolt

MATERIAL
ISO VG32
EN-GJL-200
EN-GJL-200

No.
1
3
6
18
19
21
22
23
25
26
28
30
35A
35B

NAME
Cable
Gland
Stuffing Box
Air Passage
Guide Vane
Rotor
Suction Cover
Strainer
Mechanical Seal
Oil seal
Middle plate
Oil distributor
Oil screw
Oil screw

MATERIAL
H07RN-F
EN-GJL-200
EN-GJL-200
EN-GJL-200
EN-GJL-200
EN-GX12Cr12
EN-GX12Cr12
DIN 1.0040+EN-X5CrNi18-10
Silicon Carbide
Nitrile Rubber
DIN1.4008
Plastic
EN-X5CrNi18-10
EN-X5CrNi18-10

No.
36
48
50
52A
52B
53
54
55
56
60
64
71
72

NAME
Lubricant
Threaded flange
Motor Bracket
Upper Bearing
Lower Bearing
Motor Protector
Shaft
Rotor
Stator
Bearing Housing
Motor Frame
Shaft Sleeve
Eye Bolt

MATERIAL
ISO VG32
EN-GJL-200
EN-GJL-200

DIN 1.4021

EN-GJL-150
EN-GJL-200
EN-X5CrNi18-10

150TRN440

DIN 1.4021

EN-GJL-150
EN-GJL-200
EN-X5CrNi18-10
EN-X5CrNi18-10

We reserve the right to change specifications and designs herein for improvement without prior notice. Our pumps are for professional use only. In the event that
Tsurumi (Europe) GmbH have, in exceptional cases taken over, a manufacturers warranty, this entitles the end-user to assert remedy free of charge against Tsurumi
(Europe) GmbH due to any defect to the product occurring during the guarantee period (see below), also then when the warranty claims against the seller do not or
no longer exist. In the event of malfunction, which is attributable to the improper handling by the enduser, no guarantee claim shall arise. Further claims shall not
result from the warranty, unless if something to the contrary has explicitly been determined. The decision as to whether remedy is effected by way of replacement
or repair shall be at the choice of Tsurumi (Europe) GmbH. The claims shall be time barred after a period of three months after expiry of the guarantee period,
however, not before expiry of the warranty period which is valid towards the seller. In the event of doubt, the warranty period shall correspond with the warranty
period which is valid between the end-user and his seller.

Heltorfer Strae 14
D-40472 Dsseldorf
Tel.: +49 (0)211-4179373
Fax: +49 (0)211-4791429
Email: sales@[Link]
[Link]

Your supplier
Cat. no. TRN-E-03/08

Tsurumi (Europe) GmbH