Scribd
Upload
84 views11 pages

LOBP T-0622 Design Thickness Check

This document summarizes the design check calculations for various components of a dosing vessel, including: 1) The shell thickness calculation shows a minimum required thickness of 0.165 mm, less than the code minimum of 1.5 mm. 2) Thickness calculations for the conical bottom, circular flat head, and half pipe jacket also show required thicknesses less than the 1.5 mm code minimum. 3) A half pipe jacket design check per a non-mandatory appendix is also included, showing the required and permissible jacket pressures. 4) Design notes indicate the minimum permitted thickness for shells and heads is 1.5 mm per code requirements.

Uploaded by

Anant Kumbhejkar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
84 views11 pages

LOBP T-0622 Design Thickness Check

This document summarizes the design check calculations for various components of a dosing vessel, including: 1) The shell thickness calculation shows a minimum required thickness of 0.165 mm, less than the code minimum of 1.5 mm. 2) Thickness calculations for the conical bottom, circular flat head, and half pipe jacket also show required thicknesses less than the 1.5 mm code minimum. 3) A half pipe jacket design check per a non-mandatory appendix is also included, showing the required and permissible jacket pressures. 4) Design notes indicate the minimum permitted thickness for shells and heads is 1.5 mm per code requirements.

Uploaded by

Anant Kumbhejkar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd

PROJECT: IOCL KOLKATA LOBP

DESIGN CHECK FOR T-0622


4T Dosing Vessel 2
CODE: ASME SECTION VIII DIV.1 2015
Wall
SHELL
Static (Water)head height 1650 mm

Pressure due to liquid head 16.19 Kpa

P = Internal design pressure 0 Kpa


R = Inside Radius of Shell
consideration, 1000 mm

S = Maximum allowable stress value 115 N/mm2

E = Joint efficiency 0.85

CA =Corrosion allowance 0 mm

t = minimum required thickness of shell

t = minimum required thickness of shell 0.1656072467 mm

Note: The thickness required was less than the Code Minimum,
therefore the Code Minimum value of 1.5000 mm. per UG-16 will be
used
Wall Thickness Calculation Check
CONICAL BOTTOM CIR
Static (Water)head height 2131 mm Static (Water)head heig

Pressure due to liquid head 20.91 Kpa Pressure due to liquid h


cone
69.775139 deg C = Factor
(apex) angle of the cone
0.3457027123 rad d= diameter

D= Inside dia.of conical head 2100 mm

t = minimum required thickness of cone t = minimum require

t = minimum required thickness of cone 0.6496477437 mm t = minimum require

Note: The thickness required was less than the Code Minimum, therefore the Note: The thickness req
Code Minimum value of 1.5000 mm. per UG-16 will be used therefore the Code Mini
used
CIRCULAR FLAT HEAD
atic (Water)head height 2131 mm

essure due to liquid head 20.91 Kpa

= Factor 0.2

= diameter 200 mm

= minimum required thickness of Flat head

= minimum required thickness of flat hea 1.308015 mm

ote: The thickness required was less than the Code Minimum,
erefore the Code Minimum value of 1.5000 mm. per UG-16 will be
sed
Half pipe Jacket Design Check per Non

K-Factor = 74.32 Refer FIG. EE - 2 and EE - 3 of APPENDIX EE

P1 Jacket Pressure = 999.942 Kpa

Half-Pipe Jacket Thickness 4 mm

r =Inside radius of
jacket defined in Fig. EE- 40.5 mm

S1 = allowable tensile stress


of jacket material at design 86.9 N/mm2
temperature

Req'd Half-Pipe Jacket Thickness per App. EE-1, Eqn. (2)

Tj = 0.552756

Minimum Fillet Weld Size (Based on Jacket Thickness)

Tj*1.414 = 5.656 mm
gn Check per NonMandatory Appendix EE
STEP 1: The required thickness of the shell due to internal pressure is
calculated from eq. (1) of UG-27 a

t= 0.1656072467

STEP 2: Selected Shell thickness 8 mm

STEP 3: Longitudinal Stress in Shell due to Internal Pressure

S' = 1.01165625 N/mm2

STEP 4: Permissible Jacket Pressure per Appendix EE-1, Equation (1)

P'= 2.307432 N/mm2

P' = 2307.432 Kpa

STEP 5: Jacket Pressure VS Permissible Jacket Pressure

Design is adequate
DESIGN NOTES:

1) The minimum thickness permitted for shells and heads, after forming and regardless of pro
ng and regardless of product form and material, shall be 1/16 in. (1.5 mm) exclusive of any corrosion allowance
any corrosion allowance

You might also like