1. Slab: Plate1 - Panel no.

1
1.1. Reinforcement:

·0 Type : RC floor
·1 Main reinforcement direction : 0°
·2 Main reinforcement grade : B500C; Characteristic
strength = 500.00 MPa
Horizontal branch of the stress-strain diagram
·3 Ductility class :C
·4 Bar diameters bottom d1 = 1.2 (cm) d2 = 1.2 (cm)
top d1 = 1.2 (cm) d2 = 1.2 (cm)
·5 Cover bottom c1 = 3.0 (cm)
top c2 = 3.0 (cm)
·6 Cover deviations Cdev = 1.0(cm), Cdur = 0.0(cm)

1.2. Concrete

·7 Class : C25/30; Characteristic strength = 25.00

MPa
Rectangular stress distribution [3.1.7(3)]
·8 Density : 2501.36 (kG/m3)
·9 Concrete creep coefficient : 1.47
·10 Cement class :N

1.3. Hypothesis

·11 Calculations according

to : EN 1992-1-1:2004
AC:2008
·12 Method of
reinforcement area calculations : analytical
·13 Allowable cracking
width
- upper layer : 0.40 (mm)
- lower layer : 0.40 (mm)
·14 Allowable deflection
: 3.0 (cm)
·15 Verification of punching
: yes
·16 Exposure
- upper layer : X0
- lower layer : X0
·17 Calculation type : simple
bending
·18 Structure class : S1

1.4. Slab geometry

Thickness 0.35 (m)
Contour:
edge beginning end length
x1 y1 x2 y2 (m)
1 -7.00 5.00 7.00 5.00 14.00
2 7.00 5.00 7.00 -5.00 10.00
3 7.00 -5.00 -7.00 -5.00 14.00
4 -7.00 -5.00 -7.00 5.00 10.00

Support:
n° Name dimensions coordinates edge
(m) x y
107 point 0.40 / 0.40 -7.00 5.00 —
128 point 0.40 / 0.40 -7.00 -5.00 —
146 point 0.40 / 0.40 7.00 5.00 —
163 point 0.40 / 0.40 7.00 -5.00 —
* - head present

1.5. Calculation results:

It is impossible to obtain provided reinforcement with appropriate area
Too little top reinforcement area
Too little bottom reinforcement area
Punching requirements have not been fulfilled:
Verification point 1 - Too little safety factor - reinforcement required
Verification point 1 - The value of the punching force is too big
Verification point 2 - Too little safety factor - reinforcement required
Verification point 2 - The value of the punching force is too big
Verification point 3 - Too little safety factor - reinforcement required
Verification point 3 - The value of the punching force is too big
Verification point 4 - Too little safety factor - reinforcement required
Verification point 4 - The value of the punching force is too big
For top reinforcement in the direction of X axis at the point: (-6.68, 4.00)
Ar/At = 0.03 < 1.0
For top reinforcement in the direction of X axis at the point: (-6.68, -4.67)
Ar/At = 0.07 < 1.0
For top reinforcement in the direction of X axis at the point: (-6.68, -3.40)
Ar/At = 0.92 < 1.0
For top reinforcement in the direction of Y axis at the point: (-6.68, 4.00)
Ar/At = 0.05 < 1.0
For top reinforcement in the direction of Y axis at the point: (-6.68, -4.00)
Ar/At = 0.08 < 1.0
For top reinforcement in the direction of Y axis at the point: (-6.68, -4.67)
Ar/At = 0.10 < 1.0
For bottom reinforcement in the direction of X axis at the point: (-6.68, 4.00)
Ar/At = 0.04 < 1.0
For bottom reinforcement in the direction of X axis at the point: (-6.68,
-4.00) Ar/At = 0.04 < 1.0
For bottom reinforcement in the direction of X axis at the point: (-6.68,
-3.40) Ar/At = 0.21 < 1.0
For bottom reinforcement in the direction of Y axis at the point: (-6.68, 4.00)
Ar/At = 0.07 < 1.0
For bottom reinforcement in the direction of Y axis at the point: (-6.68,
-4.00) Ar/At = 0.07 < 1.0
For bottom reinforcement in the direction of Y axis at the point: (-6.68,
-2.75) Ar/At = 0.54 < 1.0
 1.5.1. Maximum moments + reinforcement for bending

Ax(+) Ax(-) Ay(+)

Ay(-)
Provided reinforcement (cm2/m):
10.46 10.46 10.46
10.46
Modified required reinforcement (cm2/m):
301.12 269.61 200.38
159.55
Original required reinforcement (cm2/m):
369.45 312.35 248.40
192.76
Coordinates (m):
-7.00;5.00 -7.00;5.00 -7.00;5.00
-7.00;5.00

1.5.2. Maximum moments + reinforcement for bending

Ax(+) Ax(-) Ay(+)

Ay(-)
Symbol: required area/provided area
Ax(+) (cm2/m) 301.12*/10.46 301.12*/10.46 301.12*/10.46
301.12*/10.46
Ax(-) (cm2/m) 269.61*/10.46 269.61*/10.46 269.61*/10.46
269.61*/10.46
Ay(+) (cm2/m) 200.38*/10.46 200.38*/10.46 200.38*/10.46
200.38*/10.46
Ay(-) (cm2/m) 159.55*/10.46 159.55*/10.46 159.55*/10.46
159.55*/10.46
* - Reinforcement area reduced to support contour

ULS
Mxx (kN*m/m) 3085.25 3085.25 3085.25
3085.25
Myy (kN*m/m) 1754.49 1754.49 1754.49
1754.49
Mxy (kN*m/m) -840.50 -840.50 -840.50
-840.50

Coordinates (m) -7.00;5.00 -7.00;5.00 -7.00;5.00

-7.00;5.00
Coordinates* (m) -7.00;5.00;0.00 -7.00;5.00;0.00 -7.00;5.00;0.00
-7.00;5.00;0.00
* - Coordinates in the structure global coordinate system

1.5.3. Punching
Support no. / Point Location (m) Geometry: (m)
x y a b d h
S1 -7.00 5.00 Column 0.40 0.40 -
-
S2 -7.00 -5.00 Column 0.40 0.40 -
-
S3 7.00 5.00 Column 0.40 0.40 -
-
S4 7.00 -5.00 Column 0.40 0.40 -
-

Support no. / Point Loads: (kN) Critical perimeter (m)

Q Qadm u Qadm / Q
S1 4998.39 317.96 2.34 0.06 < 1
S2 5007.58 317.96 2.34 0.06 < 1
S3 4968.83 317.96 2.34 0.06 < 1
S4 4983.52 317.96 2.34 0.06 < 1

Punching requirements not fulfilled for points: S1, S2, S3, S4,
Support no. / Point: S1
uo = 0.60
u1 = 2.34
rLx = 0.00
rLy = 0.00
heff = 30.8 (cm)
Ax = 10.46 (cm2)
Ay = 10.46 (cm2)
a= 1.57
n= 0.54 ()
gc = 1.50 ()
fcd = 16.67 (MPa)
vRdmax = 4.50 (MPa)
V= 784.30 (kN)
Mx = 575.95 (kN*m)
My = 1009.41 (kN*m)
A= 0.42 (m2)
Kx = 0.60
Ky = 0.60
Wx = 0.10
Wy = 0.10

vRdc = 0.44
nmin = 0.42
vEds = 27.05
cRdc= 0.12
k= 1.81
rL = 0.00 ()
vlim = 0.44 (MPa)
v= 6.95 (MPa)
A= 0.72 (m2)

Support no. / Point: S2

uo = 0.60
u1 = 2.34
rLx = 0.00
rLy = 0.00
heff = 30.8 (cm)
Ax = 10.46 (cm2)
Ay = 10.46 (cm2)
a= 1.57
n= 0.54 ()
gc = 1.50 ()
fcd = 16.67 (MPa)
vRdmax = 4.50 (MPa)
V= 807.23 (kN)
Mx = 573.07 (kN*m)
My = 1007.13 (kN*m)
A= 0.42 (m2)
Kx = 0.60
Ky = 0.60
Wx = 0.10
Wy = 0.10

vRdc = 0.44
nmin = 0.42
vEds = 27.10
cRdc= 0.12
k= 1.81
rL = 0.00 ()
vlim = 0.44 (MPa)
v= 6.96 (MPa)
A= 0.72 (m2)

Support no. / Point: S3

uo = 0.60
u1 = 2.34
rLx = 0.00
rLy = 0.00
heff = 30.8 (cm)
Ax = 10.46 (cm2)
Ay = 10.46 (cm2)
a= 1.57
n= 0.54 ()
gc = 1.50 ()
fcd = 16.67 (MPa)
vRdmax = 4.50 (MPa)
V= 817.19 (kN)
Mx = 566.46 (kN*m)
My = 995.41 (kN*m)
A= 0.42 (m2)
Kx = 0.60
Ky = 0.60
Wx = 0.10
Wy = 0.10

vRdc = 0.44
nmin = 0.42
vEds = 26.89
cRdc= 0.12
k= 1.81
rL = 0.00 ()
vlim = 0.44 (MPa)
v= 6.91 (MPa)
A= 0.72 (m2)

Support no. / Point: S4

uo = 0.60
u1 = 2.34
rLx = 0.00
rLy = 0.00
heff = 30.8 (cm)
Ax = 10.46 (cm2)
Ay = 10.46 (cm2)
a= 1.57
n= 0.54 ()
gc = 1.50 ()
fcd = 16.67 (MPa)
vRdmax = 4.50 (MPa)
V= 822.74 (kN)
Mx = 567.05 (kN*m)
My = 998.26 (kN*m)
A= 0.42 (m2)
Kx = 0.60
Ky = 0.60
Wx = 0.10
Wy = 0.10

vRdc = 0.44
nmin = 0.42
vEds = 26.97
cRdc= 0.12
k= 1.81
rL = 0.00 ()
vlim = 0.44 (MPa)
v= 6.93 (MPa)
A= 0.72 (m2)
 1.5.4. Deflection
|f(+)| = 0.0 (cm) <= fdop(+) = 3.0 (cm)
|f(-)| = 0.0 (cm) <= fdop(-) = 3.0 (cm)

1.5.5. Cracking
upper layer
ax = 0.00 (mm) <= adop = 0.40 (mm)
ay = 0.00 (mm) <= adop = 0.40 (mm)
lower layer
ax = 0.00 (mm) <= adop = 0.40 (mm)
ay = 0.00 (mm) <= adop = 0.40 (mm)

2. Loads:
Case Type List Value
1 self-weight 1 PZ Negative
1 (FE) uniform 1 PZ=-6.50(kN/m2)
2 (FE) uniform 1 PZ=-2.50(kN/m2)

Combination/Component Definition
ULS/3 1*1.35+2*1.50

3. Results - detailing
List of solutions:
Reinforcement: Wire fabrics
Solution no. Wire fabric no./type Re-usability coefficient (percent) Total
Weight
(kG)
1 56 x 10-150,5000x2350 92.98 5139.13

Results for the solution no. 1

Reinforcement zones

Bottom reinforcement
Name coordinates Provided reinforcement At
Ar At Ar
x1 y1 x2 y2
(cm2/m) (cm2/m) (cm2/m)
(cm2/m)
1/1- -7.00 5.00 7.00 1.33 10-150,5000x2350 10-
150,5000x2350 269.61 > 10.46 159.55 > 10.46
1/2- -7.00 1.82 -3.40 0.18 10-150,5000x2350 10-
150,5000x2350 27.08 > 10.46 37.99 > 10.46
1/3- -1.60 1.82 7.00 0.18 10-150,5000x2350 10-
150,5000x2350 62.36 > 10.46 33.74 > 10.46
1/4- -7.00 0.67 7.00 -5.00 10-150,5000x2350 10-
150,5000x2350 268.37 > 10.46 158.27 > 10.46

Top reinforcement
 Name coordinates Provided reinforcement At
Ar At Ar
x1 y1 x2 y2
(cm2/m) (cm2/m) (cm2/m)
(cm2/m)
1/1+ -7.00 5.00 -3.40 2.11 10-150,5000x2350 5.23
< 5.23 5.23 < 5.23
1/2+ -7.00 5.00 -0.33 2.11 10-150,5000x2350
295.89 > 5.23 195.15 > 5.23
1/3+ 1.00 5.00 7.00 3.20 10-150,5000x2350 5.23
< 5.23 5.23 < 5.23
1/4+ 3.00 5.00 7.00 2.60 10-150,5000x2350
291.26 > 5.23 191.63 > 5.23
1/5+ 4.33 3.69 7.00 1.33 10-150,5000x2350
24.15 > 5.23 4.26 < 5.23
1/6+ -7.00 3.09 -5.20 0.84 10-150,5000x2350 5.23
< 5.23 0.00 < 5.23
1/7+ -7.00 2.60 0.33 1.33 10-150,5000x2350 9.64
> 5.23 4.52 < 5.23
1/8+ -1.60 2.60 0.33 -1.12 10-150,5000x2350 5.23
< 5.23 4.52 < 5.23
1/9+ -7.00 1.82 -3.40 0.18 10-150,5000x2350 4.69
< 5.23 0.00 < 5.23
1/10+ -1.60 1.82 0.33 0.18 10-150,5000x2350 4.11
< 5.23 0.00 < 5.23
1/11+ 5.00 3.09 7.00 -2.99 10-150,5000x2350
11.53 > 5.23 0.00 < 5.23
1/12+ -7.00 0.67 0.33 -0.62 10-150,5000x2350 4.69
< 5.23 4.52 < 5.23
1/13+ -7.00 -0.13 -5.20 -2.99 10-150,5000x2350 5.23
< 5.23 0.00 < 5.23
1/14+ -4.60 -0.13 -0.33 -1.25 10-150,5000x2350 0.00
< 5.23 4.52 < 5.23
1/15+ -7.00 -1.25 -5.20 -2.99 10-150,5000x2350
10.04 > 5.23 0.00 < 5.23
1/16+ 4.33 -1.25 7.00 -3.62 10-150,5000x2350
11.68 > 5.23 5.23 > 5.23
1/17+ -7.00 -2.50 -4.00 -3.62 10-150,5000x2350 5.23
< 5.23 5.23 < 5.23
1/18+ -7.00 -2.50 -3.40 -5.00 10-150,5000x2350
23.14 > 5.23 5.23 > 5.23
1/19+ 3.00 -2.50 7.00 -5.00 10-150,5000x2350
24.29 > 5.23 5.23 > 5.23
1/20+ -7.00 -3.13 -0.33 -5.00 10-150,5000x2350
294.81 > 5.23 194.13 > 5.23
1/21+ 1.00 -3.13 7.00 -5.00 10-150,5000x2350
292.00 > 5.23 191.88 > 5.23

Insufficient top reinforcement area.

Insufficient bottom reinforcement area.

4. Material survey
·19 Concrete volume = 49.00 (m3)
·20 Formwork = 140.00 (m2)
·21 Slab circumference = 48.00
(m)
·22 Area of openings = 6.00 (m2)

·23 Steel B500C

·24 Total weight = 31.48 (kG)
·25 Density = 0.64 (kG/m3)
·26 Average diameter = 10.0 (mm)
·27 Survey according to diameters:

Diameter Length Number:

(m)
10 3.19 16

·28 Wire fabrics

·29 Weight of used reinforcement
= 5139.13 (kG)
·30 Reinforcement total weight
= 5526.85 (kG)
·31 Density = 104.88 (kG/m3)
·32 Re-usability coefficient (percent):
Weight = 7.02
- area = 7.02
·33 Global survey:

Symbol/Type Number Weight

(No.) (kG)
10-150,5000x2350 / B 500K 56 5526.85

·34 Detailed survey:

Panel
Number Symbol/Type Pos. Dimension Cut Number
in panel
(No.) Lr / lr (m) (No.)

4 10-150,5000x2350 / B 500K 1 3.33 / 2.35 2/3 | 1/1

1
28 1.67 / 2.35 1/3 | 1/1 1

1 10-150,5000x2350 / B 500K 20 1.67 / 1.57 1/3 | 2/3

1
68 3.94 / 0.57 -|- 1
10 1.34 / 1.57 - | 2/3 2
2 0.61 / 2.35 - | 1/1 1

1 10-150,5000x2350 / B 500K 36 0.67 / 2.35 - | 1/1 1

 27 2.67 / 0.58 -|- 1
2 0.61 / 2.35 - | 1/1 1
17 0.51 / 2.35 - | 1/1 2
62 1.34 / 0.80 -|- 1
45 1.27 / 0.78 - | 1/3 1
12 1.34 / 0.72 -|- 1
53 0.84 / 0.78 - | 1/3 1

1 10-150,5000x2350 / B 500K 25 2.67 / 1.17 - | 1/2 2

20 1.67 / 1.57 1/3 | 2/3 1
2 0.61 / 2.35 - | 1/1 1
48 1.67 / 0.66 1/3 | - 1

1 10-150,5000x2350 / B 500K 60 5.00 / 0.80 1/1 | - 1

3 3.33 / 1.03 2/3 | - 1
22 1.67 / 1.17 1/3 | - 1

1 10-150,5000x2350 / B 500K 30 0.61 / 1.86 -|- 1

41 0.47 / 2.35 - | 1/1 1
32 0.61 / 1.57 - | 2/3 3
35 1.67 / 0.57 1/3 | - 1
21 0.47 / 1.57 - | 2/3 2
58 1.01 / 0.64 -|- 1
4 0.61 / 1.03 -|- 1
43 0.47 / 1.00 -|- 1
34 0.61 / 0.57 -|- 2

13 10-150,5000x2350 / B 500K 5 5.00 / 2.35 1/1 | 1/1

1

1 10-150,5000x2350 / B 500K 6 2.01 / 2.35 - | 1/1 1

59 2.01 / 1.57 - | 2/3 1
52 2.50 / 0.78 1/2 | 1/3 1
32 0.61 / 1.57 - | 2/3 1
49 0.47 / 0.66 -|- 1

1 10-150,5000x2350 / B 500K 7 5.00 / 1.03 1/1 | - 1

60 5.00 / 0.80 1/1 | - 1

1 10-150,5000x2350 / B 500K 8 2.01 / 1.03 -|- 1

52 2.50 / 0.78 1/2 | 1/3 1
42 1.67 / 1.00 1/3 | - 1
61 2.01 / 0.80 -|- 1
45 1.27 / 0.78 - | 1/3 1
23 0.47 / 1.17 -|- 1

1 10-150,5000x2350 / B 500K 9 5.00 / 1.57 1/1 | 2/3

1
11 5.00 / 0.72 1/1 | - 1

1 10-150,5000x2350 / B 500K 9 5.00 / 1.57 1/1 | 2/3

1
26 5.00 / 0.58 1/1 | - 1
1 10-150,5000x2350 / B 500K 9 5.00 / 1.57 1/1 | 2/3
1
39 5.00 / 0.61 1/1 | - 1

2 10-150,5000x2350 / B 500K 9 5.00 / 1.57 1/1 | 2/3

1
67 5.00 / 0.57 1/1 | - 1

1 10-150,5000x2350 / B 500K 66 3.94 / 1.57 - | 2/3 1

44 3.33 / 0.78 2/3 | 1/3 1
13 1.01 / 2.35 - | 1/1 1
34 0.61 / 0.57 -|- 1

1 10-150,5000x2350 / B 500K 66 3.94 / 1.57 - | 2/3 1

44 3.33 / 0.78 2/3 | 1/3 1
13 1.01 / 2.35 - | 1/1 1
57 0.61 / 0.64 -|- 1

1 10-150,5000x2350 / B 500K 64 5.00 / 1.81 1/1 | - 1

14 3.33 / 0.54 2/3 | - 1
37 1.67 / 0.50 1/3 | - 1

1 10-150,5000x2350 / B 500K 64 5.00 / 1.81 1/1 | - 1

18 2.50 / 0.50 1/2 | - 1
15 1.01 / 0.54 -|- 1
55 0.84 / 0.53 -|- 1
51 0.51 / 0.51 -|- 1

1 10-150,5000x2350 / B 500K 16 2.50 / 2.35 1/2 | 1/1

2

1 10-150,5000x2350 / B 500K 65 4.68 / 1.81 -|- 1

38 0.67 / 0.50 -|- 1
19 0.51 / 0.50 -|- 1

1 10-150,5000x2350 / B 500K 31 3.33 / 1.57 2/3 | 2/3

1
20 1.67 / 1.57 1/3 | 2/3 1
68 3.94 / 0.57 -|- 1
53 0.84 / 0.78 - | 1/3 1

1 10-150,5000x2350 / B 500K 24 5.00 / 1.17 1/1 | 1/2

2

1 10-150,5000x2350 / B 500K 31 3.33 / 1.57 2/3 | 2/3

1
28 1.67 / 2.35 1/3 | 1/1 1
56 3.33 / 0.64 2/3 | - 1

1 10-150,5000x2350 / B 500K 31 3.33 / 1.57 2/3 | 2/3

1
29 1.67 / 1.86 1/3 | - 1
 56 3.33 / 0.64 2/3 | - 1

1 10-150,5000x2350 / B 500K 33 3.33 / 0.57 2/3 | - 3

40 2.67 / 0.61 -|- 1
36 0.67 / 2.35 - | 1/1 2
34 0.61 / 0.57 -|- 1

1 10-150,5000x2350 / B 500K 64 5.00 / 1.81 1/1 | - 1

46 3.33 / 0.53 2/3 | - 1
47 1.27 / 0.53 -|- 1

1 10-150,5000x2350 / B 500K 64 5.00 / 1.81 1/1 | - 1

54 2.50 / 0.53 1/2 | - 1
50 2.50 / 0.51 1/2 | - 1

6 10-150,5000x2350 / B 500K 63 4.68 / 2.35 - | 1/1 1

1 10-150,5000x2350 / B 500K 65 4.68 / 1.81 -|- 1

4 10-150,5000x2350 / B 500K 69 5.00 / 1.95 1/1 | - 1

2 10-150,5000x2350 / B 500K 70 4.68 / 1.95 -|- 1