Owner’s Manual English

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). These
sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, this manual should be read in its
entirety. The manual should be saved and kept on hand as a convenient reference.

Main Features
This is an effect unit that’s designed specifically for bass; it generates a solid sound that takes advantage of the tone and response of the bass itself.
Use the BLEND knob to mix the direct sound to the output, and use the responsive HIGH/LOW knobs to adjust the tone intuitively.
The LINE OUT jack provides a balanced output that preserves the tonal character of the bass amp. This is convenient when connecting a mixer or recorder.

Panel Descriptions
DC IN jack CHECK indicator
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play This indicator shows whether the effect is on or off, and also doubles as the battery check
without being concerned about how much battery power you have left. indicator. The indicator lights when the effect is on.
* Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet * If you’re powering the unit with a battery and the CHECK indicator goes dim— or
of the correct voltage. Do not use any other AC adaptor, since this may cause malfunction. doesn’t light at all—when you try to turn the effect on, the battery is near depletion
and should be replaced. For instructions on changing the battery, refer to “Changing
* If the AC adaptor is connected while a battery is installed, the power AC Adaptor
the Battery.”
supply is drawn from the AC adaptor. (PSA series: optional)
* The CHECK indicator shows whether the effect is being applied or not. It does not
* We recommend that you keep batteries installed in the unit even
indicate whether the power to the device is on or not.
though you’ll be powering it with the AC adaptor. That way, you’ll be
able to continue a performance even if the cord of the AC adaptor gets
accidently disconnected from the unit.
DRIVE knob
Adjusts the amount of overdrive. Turning the knob clockwise increases the
LEVEL knob
effect (distortion).
Adjusts the volume when the effect is on.

HIGH knob
BLEND knob
Adjusts the sound level of the upper range when the effect is on.
Adjusts the output balance between the direct sound and the effect sound.

OUTPUT jack LOW knob

Connect this jack to your amp or to the Adjusts the sound level of the lower range when the effect is on.
input of another effect unit.

Bass amplifier
INPUT jack
Bass This jack accepts signals coming from a bass
or other musical instrument, or another
effects unit.
LINE OUT jack * The INPUT jack doubles as the power switch. Power
This is a balanced (TRS) type output jack. to the unit is turned on when you plug into the
Connect it to your mixer or recorder. INPUT jack; the power is turned off when the cable
is unplugged. To prevent unnecessary battery
* This cannot be used as a headphone jack. Thumbscrew consumption, be sure to disconnect the plug from
When this screw is loosened, the the INPUT jack when not using the effects unit.
Mixer pedal will open, allowing you to
* The LINE OUT jack is wired as follows.
change the battery.
* For instructions on changing
the battery, refer to
“Changing the Battery.”
Pedal switch
Recorder This switch turns the effect on/off.

Precautions When Connecting Changing the Battery Specifications

* To prevent malfunction and equipment failure, always turn 1. Hold down the pedal and loosen the thumbscrew, then BOSS BB-1X: Bass Driver
down the volume, and turn off all the units before making any open the pedal upward.
connections. Nominal Input Level -20 dBu
* The pedal can be opened without detaching the thumbscrew
* Once the connections have been completed, turn on power completely. Input Impedance 1 MΩ
to your various devices in the order specified. By turning on Nominal Output Level -20 dBu
devices in the wrong order, you risk causing malfunction and/ Thumbscrew Pedal
or damage to speakers and other devices. OUTPUT: 1 kΩ
Output Impedance
Spring Base LINE OUT: 600 Ω
When powering up: Turn on the power to your bass amp Battery Snap
last. Cord Recommended Load OUTPUT: 10 kΩ or greater
Coil Spring Impedance LINE OUT: 600 Ω or greater
When powering down: Turn off the power to your bass amp
first. Guide Bush DC 9 V: Alkaline battery (9 V, 6LR61)/
Hole Power Supply Carbon-zinc battery (9 V, 6F22),
* This unit is equipped with a protection circuit. A brief interval Battery AC Adaptor (sold separately)
(a few seconds) after power up is required before the unit will Snap 54 mA
operate normally. Battery Housing
* Expected battery life under continuous
9 V Battery Current Draw use:
Alkaline: Approx. 6 hours
Use of Battery 2. Remove the old battery from the battery housing, and
These figures will vary depending on
the actual conditions of use.
* A battery was installed in the unit before it left the factory. The remove the snap cord connected to it.
73 (W) x 129 (D) x 59 (H) mm
life of this battery may be limited, however, since its primary Dimensions
3. Connect the snap cord to the new battery, and place 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
purpose was to enable testing.
the battery inside the battery housing.
* If you handle batteries improperly, you risk explosion and fluid Weight 450 g/1 lb (including battery)
* Be sure to carefully observe the battery’s polarity (+ versus -).
leakage. Make sure that you carefully observe all of the items Owner’s Manual,
related to batteries that are listed in “USING THE UNIT SAFELY” 4. Slip the coil spring onto the spring base on the back of Leaflet (“USING THE UNIT SAFELY,”
and “IMPORTANT NOTES” (supplied on a separate sheet). Accessories
the pedal, and then close the pedal. “IMPORTANT NOTES,” and “Information”),
* When operating on battery power only, the unit’s indicator will Alkaline battery (9 V, 6LR61)
* Carefully avoid getting the snap cord caught in the pedal, coil
become dim when battery power gets too low. Replace the Option
spring, and battery housing. AC adaptor (PSA series)
battery as soon as possible.
(sold separately)
* Batteries should always be installed or replaced before 5. Finally, insert the thumbscrew into the guide bush
connecting any other devices. This way, you can prevent hole and fasten it securely. * 0 dBu = 0.775 Vrms
malfunction and damage.
* In the interest of product improvement, the specifications and/
* The use of an AC adaptor is recommended as the unit’s power or appearance of this unit are subject to change without prior
consumption is relatively high. Should you prefer to use notice.
batteries, please use the alkaline type.

Setting Samples

Standard Tight

Slap Drive Solo

Copyright © 2014 ROLAND CORPORATION

All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.