12
HYUNDAI
HYUNDAI MANUAL
CONTENTS
APPLICATIONS
7
GENERAL OPERATION
SPECIAL FUNCTIONS
12
TIPS & HINTS
REMOTE CONTROL PROGRAMMING
APPLICATIONS
MODEL CABLE
Accent ADC110-B
Atos ADC110-B
7 Centennial ADC110-B
Coupe ADC110-B
Elantra / lantra ADC110-B
Excel ADC110-B
Galloper ADC110-B
Getz ADC110-B
Grandeur ADC110-B
12
H-1 ADC110-B
H-1 Truck ADC110-B
H-100 ADC110-B
H-100 Truck ADC110-B
Marcia ADC110-B
Matrix ADC110-B
S coupe ADC110-B
Santa fe ADC110-B
Santamo ADC110-B
Sonata ADC110-B
Taxi ADC110-B
Terracan ADC110-B
Trajet XG ADC110-B
Tucson ADC110-B
XG ADC110-B
GENERAL OPERATION
INTRODUCTION
The Hyundai Immobiliser system called the SMARTRA manufactured
by Bosch consists of the SMARTRA ECU which has its own CPU which
controls the vehicles immobiliser in conjunction with the engine 7
management ECU.
There are 3 basic systems used on the range of vehicles :-
SYSTEM 1
BLACK key system—TEXTON Read only key head
12
Minimum keys required for programming 2.
Maximum keys programmed 5.
SYSTEM 2
BLUE key system—ENCRYPT key system
Minimum keys required for programming 2.
Maximum keys programmed 4.
SYSTEM 3
GREEN key system—SHINCHANG ENCRYPT
Minimum keys required for programming 2.
Maximum keys programmed 4.
PIN CODE ENTRY
On earlier vehicles the pin code is a 4 digit code, which is standard
and set to 2345.
On later systems the pin code is a 6 digit code, and available from
the dealer.
GENERAL OPERATION
KEY PROGRAMMING (WITH MASTER KEY)
Elantra, Lantra, Coupe, S Coupe, Sonata, Sonica, Accent 1996 +
Atos, Starex 1998 +
7 Galloper 1999 +
Procedure
1. Insert Master Key in ignition.
2. Switch Ignition OFF to ON 5 times.
3. Remove Master key.
4. Insert NEW key into IGNITION and TURN IGNITION ON.
12 5. Turn ignition OFF and remove key.
6. Repeat 4 to 5 for all additional keys and any existing keys.
NOTE : IF AN EXISTING KEY IS NOT REGISTERED AT THIS STAGE
THEN IT WILL BE DELETED FROM THE SYSTEM.
NOTE 2 : THE PROCEDURE FROM 3 TO 5 MUST BE COMPLETED
WITHIN 15 SECONDS.
SPECIAL FUNCTIONS
KEY PROGRAMMING—SYSTEM 1
DIAGNOSTIC MENU
ECU IDENTIFICATION From the main DIAGNOSTIC MENU
FAULT CODES 7
SPECIAL FUNCTIONS
select the SPECIAL FUNCTIONS.
PRESS ENTER KEY
DIAGNOSTIC MENU
Select PROGRAM KEYS.
> PROGRAM KEYS 12
> CLEAR KEYS
> KEYS PROGRAMMED
PRESS ENTER KEY
Enter security code.
SECURITY CODE NOTE : This code is normally 2345
____ NOTE 2 : If this is incorrect then the
dealer who supplied the vehicle may
have changed it. If this is so, please
contact the dealer.
SECURITY CODE
2345
IS THIS CORRECT
OK = ENTER CLEAR =BACK
If key programming is successful, then
procedure complete is displayed.
PROCEDURE COMPLETE NOTE : REPEAT PROCEDURE FOR ALL
ADDITIONAL KEYS REQUIRED.
SPECIAL FUNCTIONS
KEY CLEARING—SYSTEM 1
DIAGNOSTIC MENU
Select CLEAR KEYS from SPECIAL
> PROGRAM KEYS
7 > CLEAR KEYS FUNCTIONS menu.
> KEYS PROGRAMMED
PRESS ENTER KEY
Enter security code.
SECURITY CODE NOTE : This code is normally 2345
12
____ NOTE 2 : If this is incorrect then the
dealer who supplied the vehicle may
have changed it. If this is so, please
contact the dealer.
SECURITY CODE
2345
IS THIS CORRECT
OK = ENTER CLEAR =BACK
PROCEDURE COMPLETE When all keys are cleared PROCEDURE
COMPLETE will be displayed.
SPECIAL FUNCTIONS
KEY PROGRAMMING—SYSTEM 2
DIAGNOSTIC MENU
ECU IDENTIFICATION From the main DIAGNOSTIC MENU se-
FAULT CODES lect the SPECIAL FUNCTIONS. 7
SPECIAL FUNCTIONS
PRESS ENTER KEY
DIAGNOSTIC MENU
Select PROGRAM KEYS.
> PROGRAM KEYS 12
> KEYS PROGRAMMED
> LIMP HOME MODE
PRESS ENTER KEY
Enter 6 digit security code.
SECURITY CODE
______
SECURITY CODE NOTE : The 6 digit code is available
from the vehicle dealer.
123456
IS THIS CORRECT
OK = ENTER CLEAR =BACK
Switch IGNITION ON and press the
SWITCH IGNITION ON ENTER key.
AND THEN PRESS ENTER
SPECIAL FUNCTIONS
KEY PROGRAMMING—SYSTEM 2
PROGRAM KEYS The key in the ignition will be added to
INSERT NEXT KEY the system.
7 & THEN PRESS ENTER
To program additional keys press the
ENTER key, or BACK to exit program-
ming.
PROGRAM KEYS
If ENTER is pressed then additional
PROCEDURE COMPLETE keys can be programmed.
12
Repeat for all additional keys.
If BACK is pressed and all keys have
been programmed PROCEDURE COM-
PLETE is displayed.
LIMP HOME MODE—SYSTEM 2
DIAGNOSTIC MENU
ECU IDENTIFICATION From the main DIAGNOSTIC MENU
FAULT CODES select the SPECIAL FUNCTIONS.
SPECIAL FUNCTIONS
PRESS ENTER KEY
Select LIMP HOME MODE.
DIAGNOSTIC MENU
> PROGRAM KEYS
> CLEAR KEYS Insert security code 2345 and this will
> LIMP HOME MODE enable one start to get the vehicle to a
dealer or workshop if further testing is
required.
PRESS ENTER KEY
SPECIAL FUNCTIONS
PIN CODE CONVERTER
DIAGNOSTIC MENU
EURO From the main DIAGNOSTIC MENU
USA select the HYUNDAI SYSTEMS. 7
HYUNDAI SYSTEMS
PRESS ENTER KEY
DIAGNOSTIC MENU
PINCODE
Select PINCODE.
TYPE 1 12
TYPE 2
TYPE 3
TYPE 4
PRESS ENTER KEY
Press the ENTER button
PINCODE CONVERTER
PRESS ENTER KEY
SECURITY CODE
Insert the last 6 digits of the VIN or
123456 CHASSIS number.
IS THIS CORRECT
OK = ENTER CLEAR =BACK
Then press ENTER
VIN TO PINCODE Please wait for program to convert the
number, this will take 5 minutes.
PLEASE WAIT
..............
The 6 digit Pin code will then be dis-
VIN TO PINCODE played for use on key programming.
PIN : 582656 NOTE : This will use a token.
TIPS & HINTS
When programming keys, please note the following:
The transponder aerial has a resistance of 21.5 Ohms
The immobiliser control unit does not return any information to the
7 tester about the key programming procedure, therefore it is possible
to input an incorrect security code and continue through the pro-
gramming procedure.
When programming a key, the horn will sound for 0.2 second to sig-
nify the key programming action.
12 Once the first key has been programmed you should turn the ignition
on with a second key and wait for 10 seconds, the horn should again
sound- if it doesn't, switch on the HRW (Heated Rear Window
Switch) to complete the programming phase.
NOTE :-2 keys must be programmed to close the procedure.
On Hyundai & Kia vehicles the Clutch must be depressed to start the
vehicle.
Note: The aerial is not programmed.
REMOTE CONTROL PROGRAMMING
Procedure
1. Remove the lower crash panel and locate the Remote control receiver unit.
2. The switch on the side of the unit should be switched to the SET position and the ignition on.
3. Press the lock button or unlock button on all Transmitters quickly. 7
4. Return the switch to OFF position and then test remote control.
12
