Installer I/O Table

Function Connection Example On vehicle

Trigger 1 Crank Angle Sensor Reluctor, Proximity, Optical or Hall E
Trigger 2 Cam angle sensor (set to 1JZ VVTi) E
Analog Temp Input 1 Engine coolant temp sensor NTC Thermistor sensors Only E
Analog Temp Input 2 Intake air temp sensor (TMAP) E
Analog Temp Input 3 Oil temp sensor E
Analog Temp Input 4 AC Evaporator temp sensor c
Analog Volt 1 MAP sensor (TMAP) 0-5V Input from sensor or external controller E
Analog Volt 2 Pedal position sensor (main) C
Analog Volt 3 Pedal position sensor (sub) C
Analog Volt 4 Oil pressure sensor (10 BAR) E
Analog Volt 5 Fuel pressure sensor (10 BAR) E
Analog Volt 6 Cruise control steering wheel switch C
Analog Volt 7 Throttle position sensor (main) E
Analog Volt 8 Throttle position sensor (sub) E
Analog Volt 9 AC Pressure sensor c
+5V Out TPS, MAP and pressure sensor power +5V Power OUT E
+8V Out ----------------------------------------------------------------------
Ignition 1 Smart coil 1 To coils E
Ignition 2 Smart coil 2 E
Ignition 3 Smart coil 3 E
Ignition 4 Smart coil 4 E
Ignition 5 Smart coil 5 E
Ignition 6 Smart coil 6 E
Injection 1 Injector 1 Wire Inj 1 to cyl 1, 2 to 2, 3to 3 etc... E
Injection 2 Injector 2 E
Injection 3 Injector 3 E
Injection 4 Injector 4 E
Injection 5 Injector 5 Use spare Injection channels for E
Injection 6 Injector 6 switching type Auxiliary Outputs E
Injection 7 /AUX Traction control on light
Injection 8 / AUX Cruise control on light
Auxiliary Output 1 VVTi Solenoid High Frequency PWM or VVT Control. E
Auxiliary Output 2 Engine Fan control relay 1 C
Auxiliary Output 3 Engine Fan control relay 2 /3 3W-ISC Solenoid must be wired to Aux1 & Aux2. C
Auxiliary Output 4 C
Auxiliary Output 5 Air conditioning clutch PWM less than 300 Hz or GP switching. E
Auxiliary Output 6 Boost controller solenoid E
Auxiliary Output 7 Fuel pump control ISC Stepper. High side driven loads. C
Auxiliary Output 8 E-throttle relay C
Auxiliary Output 9 (E-throttle Motor +) E Throttle Motor or GP Output. E
Auxiliary Output 10 (E-throttle Motor -) E
Knock 1 Knock sensor front Knock Sensors Only E
Knock 2 Knock sensor rear E
Digital Input 1 High boost switch Frequency Input, Switch Input or VVT Position C
Digital Input 2 Air conditioning on switch C
Digital Input 3 Brake switch C
Digital Input 4 Clutch switch C
Digital Input 5 Oil pressure switch input Frequency Input or Switch Input E
Digital Input 6 Neutral position switch C
Digital Input 7 Launch control switch C
Digital Input 8 Traction control on switch C
Digital Input 9 CANBUS2 low CAN2 or Switch Input Only C
Digital Input 10 CANBUS2 high C
MES Sensor Green Wire (pin 5) LSU 4.9 Wideband Lambda Sensor E
RE Sensor Black Wire (pin 6) E
Heater Sensor White Wire (pin 3) E
IPE Sensor Yellow Wire (pin 2) E
APE Sensor Red Wire (pin 1) E
e=37 c=17
CANBUS Inputs Left front wheel speed All on CANBUS2 DI9/10 E +12v
Right front wheel speed E +12v
Left rear wheel speed E shield gnd
Right rear wheel speed E gnd out
CANBUS Outputs to dash Check engine light E ground
Charge light E ground
Oil pressure gauge (light type function only) E shield gnd
Coolant temperature E gnd out
Tachometer E ground
Speedo (unsure on odo function) E ground
E=47 C=17