1
SPECIFICATION SHEET
(semi-formal trouser)
SUBJECT FACULTY - MS. ABOLI NAIK
BY
NEERAJ DHAKA(BFT/17/139)
DEPARTMENT OF FASHION TECHNOLOGY
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, MUMBAI
2
Manufacture’s Name: Shahi Exports
Product Overview:
Product ID AB112 Design ID XXXX
Segment Boys Family Semi-formal Wear
Brand Zara Designer Neeraj
Product Type Men’s Pant Size Range XXXX
Sample Size Waist 32” Buyer Inditex
Description Men’s Trouser Order to be received by 16/05/2019
3
Raw Material Specification:
Fabric Details
1. Shell Fabric
Fibre Content Poly Cotton (PC)
Fabric Fabric dyed suiting Fabric
Weave Plain
GSM 215
EPI*PPI 32*35 Fabric Swatch
Yarn Type Spun, 2 plies
Yarn Twist S8
Fabric Type Open Width
Finishes Applied Calendaring
Yarn Count XXX
2. Fabric for Pocket Bags
Fibre Content Poly Cotton (PC)
Fabric Butter Crepe (Fabric Dyed)
Weave Plain
GSM 85
EPI*PPI 55*50 Fabric Swatch
Yarn Type Spun, 2 plies
Yarn Twist S
Fabric Type Open Width
Yarn Count XXX
Thread Details
Ticket No for Needle thread 80 Type Spun, 2 plies
Ticket No for Bobbin thread 80 Content 100% polyester
Twist Level 43 TPI
4
Fusing Details
Type Woven Attachment Fusing Machine
Fusing Glaze XXX Thickness XXX
GSM XXX Critical Point 130 0C
Trims
Button
Ligne 32
Finish Natural Wooden Design Sample for
Type 4 Hole Button
Material Synthetic (Plastic)
Labels
Brand Label on Waistband
Placement As shown in flat sketch
Size 6*7 cm Design Sample for
Material Leather Label
Method of Attachment Flat form and edge
stitch
Size Label at inner side of waistband
Placement As shown in flat sketch
Size 5*4 cm Design Sample for
Material Twill fabric Label
Method of Attachment Upper side is seamed
inside waistband
Wash Care Label at inner side of waistband
Placement As shown in flat sketch
Size 5*2 cm Design Sample for
Material Polyester Label
Method of Attachment Upper side is seamed
inside waistband
5
Zipper
Type Plastic Coil Zipper
Machine Used SNLS, with one zipper attaching
presser foot
Specification Locking mechanism in puller
Length 16 cm
Button Hole
Machine Used Lockstitch Key Buttonhole
Number of Stitches 190
Length 26mm Design Sample for
Placement Width wise in waistband Buttonhole
Spacing As given in flat sketch
Type Flat, first stitch and then cut
Components
6
Pattern Specification
Pattern Measurements
Seam Measurements (cm) Seam Measurements(cm)
Side Seam 97 Waist Band Length 83
In Seam 76 Waistband Width 4
Lower Elastic Width 5.5 Lower Elastic Length 34
(Hem Length)
Body Rise 32 Front Crutch Length 27
Side (Cross) Pocket 18 Side (Cross) Pocket 6.5
Opening Length Opening Width
Cross Pocket Bag Length 29 Cross Pocket Bag 14
Width
Back Pocket Length 17 Back Pocket Width 17
Back Pocket Length 14 Back Pocket Width 7
Knee Pocket Length 19 Knee Pocket Width 16
Knee Pocket Length 16 Knee Pocket Width 7
J-Box Length 20 J-Box Width 3.5
Belt Loop Length 8 Belt Loop Width 1
Spreading and Cutting Specifications
Spreading Mode NEW/FEW
Cutting M/c 8” Flexon Scissor
Note: Ensure proper grain and pattern matching
7
Construction Details
Seams
Attachment Seam M/C Used
Side pocket facing to pocket bag Lapped + Edge stitch SNLS, 301
Pocket Bag Stitching French Seam SNLS, 301
Front Panel to Pocket bag Superimpose + Top Stitch at ¼“ SNLS, 301
Side Seam Superimpose 5 thread overlock, 516
Back Pocket Lapped SNLS, 301
Back Pocket Bag Joining French Seam SNLS, 301
Zipper joining Superimpose + Edge Stitch at J Box SNLS, 301
Front Crutch Joining Superimpose SNLS, 301
In Seam Superimpose 5 thread overlock, 516
Waistband Attachment Superimpose SNLS, 301
Hemming Hem SNLS, 301
Belt Loop Lapped + Bartack on Edge Bartacking
Button hole As mentioned under button hole Buttonhole M/C
section
Button Attaching As mentioned earlier Button Attaching M/C
8
Seam Details:
Seam Seam Class Diagram
Superimpose SS
Lapped LS
French SS
Hem -
Flat and Fell LS
9
Packaging
Folding Refer to the folding sketch
Form Flat
Cardboard No
Pins No
Packaging Detail Pack a trouser in a plastic bag
Plastic Bag XXX Micron
Plastic Bag Closure Adhesive Tape
Bag Dimensions 44*31cm
