Engineering interview questions,Mcqs,Objective Questions,Class Notes,Seminor

topics,Lab Viva Pdf free download. CIVIL | Mechanical | CSE | EEE | ECE | IT |
Chemical Online Quiz Tests for Freshers.

HOME Interview Questions MCQs *LAB VIVA CLASS NOTES SEMINAR TOPICS
ONLINE TEST GATE CAT Contact US

Home » Mechanical Engineering Multiple Choice Questions »

Engineering
300+ TOP Refrigeration and Air Conditioning –
Questions
Mechanical Engineering Multiple choice Questions and
Answers Engineering
5,671 likes

300+ TOP Refrigeration and Air

Like Page

Conditioning – Mechanical Be the first of your friends to

Engineering Multiple choice

Questions and Answers
Refrigeration and Air Conditioning Multiple
Choice Questions :-
1. Pick up the wrong statement. A refrigerant should have
(a) Tow specific heat of liquid
(b) high boiling point
(c) high latent heat of vaporisation
(d) higher critical temperature
(e) low specific volume of vapour.
Ans: b

2. A standard ice point temperature corresponds to the

temperature of
(a) water at 0°C
(b) ice at – 4°C
(c) solid and dry ice
(d) mixture of ice, water and vapour under equilibrium conditions
under NTP conditions
(e) mixture of ice and water Under equilibrium conditions.
Ans: e

3. Vapor compression refrigeration is some what like

(a) Carnot cycle
(b) Rankine cycle
(c) reversed Camot cycle
(d) reversed Rankine cycle
(e) none of the above.
Ans: e

4. Which of the following cycles uses air as the refrigerant

(a) Ericsson
(b) Stirling
(c) Carnot
(d) Bell-coleman
(e) none of the above.
Ans: d

5. Ammonia-absorption refrigeration cycle requires

(a) very little work input
(b) maximum work input
(c) nearly same work input as for vapour compression cycle
(d) zero work input
(e) none of the above.
Ans: a

6. An important characteristic of absorption system of

refrigeration is
(a) noisy operation
(b) quiet operation
(c) cooling below 0°C
(d) very little power consumption
(e) its input only in the form of heating.
Ans: b
7. The relative coefficient of performance is
(a) actual COP/fheoretical COP
(b) theoretical COP/actual COP
(c) actual COP x theoretical COP
(d) 1-actual COP x theoretical COP
(e) 1-actual COP/fheoretical COP.
Ans: a

8. Clapeyron equation is a relation between

(a) temperature, pressure and enthalpy
(b) specific volume and enthalpy
(c) temperature and enthalpy
(d) temperature, pressure, and specil volume
(e) temperature, pressure, specific volur and’enthalpy.
Ans: e

9. Clapeyron equation is applicable for registration at

(a) saturation point of vapor
(b) saturation point of liquid
(c) sublimation temperature
(d) triple point
(e) critical point.
Ans: a

10. In vapour compression cycle, the conditii of refrigerant

is saturated liquid
(a) after passing through the condenser
(b) before passing through the condensei
(c) after passing through the expansion throttle valve
(d) before entering the expansion valve
(e) before entering the compressor.
Ans: a

11. In vapor compression cycle, the condition of refrigerant

is very wet vapor
(a) after passing through the condenser
(b) before passing through the condenser
(c) after passing through the expansion or throttle valve
(d) before entering the expansion valve
(e) before entering the compressor.
Ans: e

12. In vapor compression cycle, the condition of refrigerant

is high pressure saturated liquid
(a) after passing through the condenser
(b) before passing through the condenser
(c) after passing through the expansion or thiottle valve
(d) before entering the expansion valve
(e) before entering the compressor.
Ans: d

13. In vapour compression cycle the condition of refrigerant is

superheated vapour
(a) after passing through the condenser
(b) before passing through the condenser
(c) after passing through the expansion or throttle valve
(d) before [entering the expansion valve
(e) before entering the compressor.
Ans: b

14. In vapor compression cycle the condition off refrigerant

is dry saturated vapor
(a) after passing through the condenser
(b) before passing through the condenser
(c) after passing through the expansion or throttle valve
(d) before entering the expansion valve
(e) before entering the compressor..
Ans: e

15. The boiling point of ammonia is

(a) -100°C
(b) -50°C
(c) – 33.3°C
(d) 0°C
(e) 33.3°C.
Ans: c
16. One ton of refrigeration is equal to the refrigeration
effect corresponding to melting of 1000 kg of ice
(a) in 1 hour
(b) in 1 minute
(c) in 24 hours
(d) in 12 hours
(e) in 10 hours.
Ans: c

17. One ton refrigeratiqn corresponds to

(a) 50 kcal/min
(b) 50 kcal/kr
(c) 80 kcal/min
(d) 80 kcal/hr
(e) 1000 kcal/day.
Ans: a

18. In S.J. unit, one ton of refrigeration is equal to

(a) 210 kJ/min
(b) 21 kJ/min
(c) 420 kJ/min
(d) 840 kJ/min
(e) 105 kJ/min.
Ans: a

19. The vapor compression refrigerator employs the

following cycie
(a) Rankine
(b) Carnot
(c) Reversed Rankine
(d) Brayton
(e) Reversed Carnot.
Ans: e

20. Allowable pressure on high-pressure side or ammonia

absorption system is of the order of
(a) atmospheric pressure
(b) slightly above atmospheric pressure
(c) 2-4 bars
(d) 5-6 bars
(e) 7-10 bars.
Ans: d

21. The moisture in a refrigerant is removed by

(a) evaporator
(b) safety relief valve
(c) dehumidifier
(d) driers
(e) expansion valve
Ans: d

22. The condensing pressure due to the presence of non-

condensable gases, as compared to that actually required
for condensing temperatures without non-condensable
gases,
(a) will be higher
(b) will be lower
(c) will remain unaffected
(d) may be higher or lower depending upon the nature of non-
condensable gases
(e) unpredictable.
Ans: a

23. Critical pressure of a liquid is the pressure

(a) above which liquid will remain liquid
(b) above which liquid becomes gas
(c) above which liquid becomes vapour
(d) above which liquid becomes solid
(e) at which all the three phases exist together.
Ans: a

24. Critical temperature is’ the temperature above which

(a) a gas will never liquefy
(b) a gas will immediately liquefy
(c) water will evaporate
(d) water will never evaporate
(e) none of the above.
Ans: a
25. The refrigerant for a refrigerator should have
(a) high sensible heat
(b) high total heat
(c) high latent heat
(d) low latent heat
(e) low sensible heat
Ans: c

26. Rating of a domestic refrigerator is of the order of

(a) 0.1 ton
(b) 5 tons
(c) 10 tons
(d) 40 tons
(e) 100 tons.
Ans: a

27. The COP of a domestic refrigerator

(a) is less than 1
(b) is more than 1
(c) is equal to 1
(d) depends upon the make
(e) depends upon the weather conditions.
Ans: b

28. The domestic refrigerator uses following type of

compressor
(a) centrifugal
(b) axial
(c) miniature sealed unit
(d) piston type reciprocating
(e) none of the above.
Ans: d

29. Presence of moisture in a refrigerant affects the

working of
(a) compressor
(b) condenser
(c) evaparator
(d) expansion valve.
(e) heat transfer.
Ans: d

30. Refrigeration in aeroplanes usually employs the

following refrigerant
(a) Co2
(b) Freon-11
(c) Freon-22
(d) Air
(e) none of the above.
Ans: d

31. Domestic refrigerator working on vapour compression

cycle uses the following type of expansion device
(a) electrically operated throttling valve
(b) manually operated valve
(c) thermostatic valve
(d) capillary tube
(e) expansion valve.
Ans: d

32. Air refrigeration operates on

(a) Carnot cycle
(b) Reversed Carnot cycle
(c) Rankine cycle
(d) Erricson cycle
(e) Brayton cycle.
Ans: e

33. Air refrigeration cycle is used in

(a) domestic refrigerators
(b) commercial refrigerators
(c) air conditioning
(d) gas liquefaction
(e) such a cycle does not exist.
Ans: d

34. In a vapor compression cycle, the refrigerant

immediately after expansion valve is
(a) liquid
(b) sub-cooled liquid
(c) saturated liquid
(d) wet vapour
(e) dry vapour.
Ans: d

35. The vapor pressure of refrigerant should be

(a) lower than atmospheric pressure
(b) higher than atmospheric pressure
(c) equal to atmospheric pressure
(d) could be anything
(e) none of the above.
Ans: b

36. For better COP of refrigerator, the pressure range corresponding

to temperature in evaporator and condenser must be
(a) small
(b) high
(c) euqal
(d) anything
(e) under some conditions small and under some conditions high.
Ans: a

37. The bank of tubes at the back of domestic refrigerator are

(a) condenser tubes
(b) evaporator tubes
(c) refrigerant cooling tubes
(d) capillary tubes
(e) throttling device.
Ans: a

38. The higher temperature in vapour compression cycle occurs at

(a) receiver
(b) expansion valve
(c) evaporator
(d) condenser discharge
(e) compressor discharge.
Ans: e
39. Highest temperature encountered in refrigeration cycle should be
(a) near critical temperature of refrigerant
(b) above critical temperature
(c) at critica. temperature
(d) much below critical temperature
(e) could be anywhere.
Ans: d

40. In refrigerator, liquid receiver is required between condenser and

flow controlling device, if quantity of refrigerant for system is
(a) less than 2 kg
(b) more than or equal to 3.65 kg
(c) more than 10 kg
(d) there is no such consideration
(e) pone of the above.
Ans: b

41. Absorption system normally uses the following refrigerant

(a) Freon-11
(b) Freon-22
(c) C02
(d) S02
(e) ammonia.
Ans: e

42. One of the purposes of sub-cooling the liquid refrigerant is to

(a) reduce compressor overheating
(b) reduce compressor discharge temperature
(c) increase cooling effect
(d) ensure that only liquid and not the vapour enters the expansion
(throttling) valve
(e) none of the above.
Ans: d

43. The value of COP in vapour compression cycle is usually

(a) always less than unity
(b) always more than unity
(c) equal to unity
(d) any one of the above
(e) none of the above.
Ans: b

44. In a refrigeration system, heat absorbed in comparison to heat

rejected is
(a) more
(b) less
(c) same
(d) more for small capacity and less for high capacity
(e) less for small capacity and more for high capacity.
Ans: b

45. Condensing temperature in a refrigerator is the temperature

(a) of cooling medium
(b) of freezing zone
(c) of evaporator
(d) at which refrigerant gas becomes liquid
(e) condensing temperature of ice.
Ans: d

Refrigeration and Air Conditioning Interview Questions

and Answers pdf:-
46. Formation of frost on evaporator in refrigerator
(a) results in loss of heat due to poor heat transfer
(b) increases heat transfer rate
(c) is immaterial
(d) can be avoided by proper design
(e) decreases compressor power.
Ans: a

47. In refrigerators, the temperature difference between the

evaporating refrigerant and the medium being cooled should be
(a) high, of the order of 25°
(b) as low as possible (3 to 11°C)
(c) zero
(d) any value
(e) none of the above.
Ans: b
48. In a flooded evaporator refrigerator, an accumulator at suction of
compressor is used to
(a) collect liquid refrigerant and prevent it from going to compressor
(b) detect liquid in vapour
(c) superheat the vapour
(d) collect vapours
(e) increase refrigeration effect.
Ans: a

49. Accumulators should have adequate volume to store refrigerant

charge at least
(a) 10%
(b) 25%
(c) 50%
(d) 75%
(e) 100%.
Ans: c

50. At lower temperatures and pressures, the latent heat of

vaporisation of a refrigerant
(a) decreases
(b) increases
(c) remains same
(d) depends on other factors
(e) none of the above.
Ans: b

Refrigeration and Air Conditioning Objective Questions

and Answers pdf :-
51. A refrigeration cycle operates between condenser
temperature of + 27°C and evaporator temperature of-
23°C. The Cannot coefficient of performance of cycle will be
(a) 0.2
(b) 1.2
(c) 5
(d) 6
(e) 10.
Ans: c
52. Which of the following is not a desirable property of a
refrigerant
(a) high triiscibility with oil
(b) low boiling point
(c) good electrical conductor
(d) large latent heat
(e) non-inflammable.
Ans: c

53. In vapor compression refrigeration system, refrigerant

occurs as liquid between
(a) condenser and expansion valve
(b) compressor and evaporator
(c) expansion valve and evaporator
(d) compressor and condenser
(e) none of the above.
Ans: c

54. Pick up the correct statement about giving up of heat

from one medium to other in ammonia absorption system
(a) strong solution to weak solution
(b) weak solution to strong solution
(c) strong solution to ammonia vapour
(d) ammonia vapour to weak solution
(e) ammonia vapour to strong solution.
Ans: b

55. Efficiency of a Carnot engine is given as 80%. If the-

cycle direction be reversed, what will be the value of COP of
reversed Carnot cycle
(a) 1.25
(b) 0.8
(c) 0.5
(d) 0.25
(e) none of the above.
Ans: d

56. Highest pressure encountered in a refrigeration system

should be
(a) critical pressure of refrigerant
(b) much below critical pressure
(c) much above critical pressure
(d) near critical pressure
(e) there is no such restriction.
Ans: b

57. If a heat pump cycle operates between the condenser

temperature of +27°C and evaporator temperature of –
23°C, then the Carnot COP will be
(a) 0.2
(b) 1.2
(c) 5
(d) 6
(e) 10.
Ans: d

58. A certain refrigerating system has a normal operating

suction pressure of 10 kg/cm gauge and condensing
pressure of about 67 kg/cm. The refrigerant used is
(a) Ammonia
(b) Carbon dioxide
(c) Freon
(d) Brine
(e) Hydrocarbon refrigerant.
Ans: b

59. Aqua ammonia is used as refrigerant in the following

type of refrigeration system
(a) compression
(b) direct
(c) indirect
(d) absorption
(e) none of the above.
Ans: d

60. If the evaporator temperature of a plant is lowered,

keeping the condenser temperature constant, the h.p. of
compressor required will be
(a) same
(b) more
(c) less
(d) more/less depending on rating
(e) unpredictable.
Ans: b

61. In a refrigeration cycle, the flow of refrigerant is controlled by

(a) compressor
(b) condenser
(c) evaporator
(d) expansion valve
(e) all of the above.
Ans: d

62. Where does the lowest temperature occur in a vapour compression

cycle ?
(a) condenser
(b) evaporator
(c) compressor
(d) expansion valve
(e) receiver.
Ans: b

63. The leaks in a refrigeration system using Freon are detected by

(a) halide torch which on detection produces greenish flame lighting
(b) sulphur sticks which on detection gives white smoke
(c) using reagents
(d) smelling
(e) sensing reduction in pressure.
Ans: a

64. rick up the incorrect statement

(a) lithium bromide used in vapour absorption cycle is nonvolatile
(b) lithium bromide plant can’t operate below 0°C
(c) a separator is used in lithium bromide plant to remove the
unwanted water vapour by condensing
(d) concentration of solution coming out of lithium bromide generator
is more in comparison to that entering the generator
(e) weak solution in liquid heat exchanger gives up heat to the strong
solution.
Ans: c

65. The lower horizontal line of the refrigeration cycle plotted on

pressure-enthalpy-diagram represents
(a) condensation of the refrigerant vapour
(b) evaporation of the refrigerant liquid
(c) compression of the refrigerant vapour
(d) metering of the refrigerant liquid
(e) none of the above.
Ans: b

66. Mass flow ratio of NH3 in comparison to Freon-12 for same

refrigeration load and same temperature limits is of the order of
(a) 1 : 1
(b) 1 : 9
(c) 9 : 1
(d) 1 : 3
(e) 3 : 1
Ans: b

67. Freon group of refrigerants are

(a) inflammable
(d) toxic
(c) non-inflammable and toxic
(d) non-toxic and inflammable
(e) non-toxic and non-inflammable.
Ans: e

68 Ammonia is
(a) non-toxic
(b) non-inflammable
(c) toxic and non-inflammable
(d) highly toxic and inflammable
(e) none of the above.
Ans: d
69. In vapour compression cycle using NH3 as refrigerant, initial
charge is filled at
(a) suction of compressor
(b) delivery of compressor
(c) high pressure side close to receiver
(d) low pressure side near receiver
(e) anywhere in the cycle.
Ans: c

70. Short horizontal lines on pressure-enthalpy chart show

(a) constant pressure lines
(b) constant temperature lines
(c) constant total heat lines
(d) constant entropy lines
(e) constant volume lines.
Ans: a

71. On the pressure-enthalpy diagram, condensation and

desuperheating is represented by a horizontal line because the process
(a) involves no change in volume
(b) takes place at constant temperature
(c) takes place at constant entropy
(d) takes place at constant enthalpy
(e) takes place at constant pressure.
Ans: e

72. One ton of the refrigeration is

(a) the standard unit used in refrigeration problems
(b) the cooling effect produced by melting 1 ton of ice
(c) the refrigeration effect to freeze 1 ton of water at 0°C into ice at 0°C
in 24 hours
(d) the refrigeration effect to produce 1 ton of ice at NTP conditions
(e) the refrigeration effect to produce 1 ton of ice in 1 hour time.
Ans: c

73. Superheating in a refrigeration cycle

(a) increases COP
(b) decreases COP
(c) COP remains unaltered
(d) other factors decide COP
(e) unpredictable.
Ans: b

74. For proper refrigeration in a cabinet, if the temperature and

vapour pressure difference between cabinet and atmosphere is high,
then
(a) bigger cabinet should be used
(b) smaller cabinet should be used
(c) perfectly tight vapour seal should be used
(d) refrigerant with lower evaporation temperature should be used
(e) refrigerant with high boiling point must be used.
Ans: c

75. Choose the correct statement

(a) A refrigerant should have low latent heat
(b) If operating temperature of system is low, then refrigerant with
low boiling point should be used
(c) Precooling and subcooling bf refrigerant are same
(d) Superheat and sensible heat of a. refrigerant are same
(e) Refrigerant is inside the lubes in case of a direct-expansion chiller.
Ans: b

76. The suction pipe diameter of refrigerating unit compressor in

comparison to delivery side is
(a) bigger
(b) smaller
(c) equal
(d) smaller/bigger depending on capacity
(e) unpredictable.
Ans: a

77. Moisture in freon refrigeration system causes

(a) ineffective refrigeration
(b) high power consumption
(c) freezing automatic regulating valve
(d) corrosion of whole system
(e) breakdown of refrigerant.
Ans: c
78. The advantage of dry compression is that
(a) it permits higher speeds to be used
(b) it permits complete evaporation in the evaporator
(c) it results in high volumetirc and mechanical efficiency
(d) all of the above
(e) none of the above.
Ans: d

79. Choose the wrong statement

(a) Temperature of medium being cooled must be below that of the
evaporator
(b) Refrigerant leaves the condenser as liquid
(c) All solar thermally operated absorption systems are capable only of
intermittent operation
(d) frost on evaporator reduces heat transfer
(e) refrigerant is circulated in a refrigeration system to transfer heat.
Ans: a

80. Under-cooling in a refrigeration cycle

(a) increases COP
(b) decreases COF
(c) COP remains unaltered
(d) other factors decide COP
(e) unperdictable.
Ans: a

81. For obtaining high COP, the pressure range of

compressor should be
(a) high
(b) low
(c) optimum
(d) any value
(e) there is no such criterion.
Ans: b

82. The coefficient of performance is the ratio of the

refrigerant effect to the
(a) heat of compression
(b) work done by compressor
(c) enthalpy increase in compressor
(d) all of the above
(e) none of the above.
Ans: d

83. The C.O.P of a refrigeration cycle with increase in

evaporator temperature, keeping condenser temperature
constant, will
(a) increase
(b) decrease
(c) remain unaffected
(d) may increase or decrease depending on the type of refrigerant used
(e) unpredictable.
Ans: a

84. Vertical lines on pressure-enthalpy chart show constant

(a) pressure lines
(b) temperature lines
(c) total heat lines
(d) entropy lines
(e) volume lines.
Ans: c

85. Most of the domestic refrigerators work on the

following refrigeration system
(a) vapour compression
(b) vapour absorption
(c) carnot cycle
(d) electrolux refrigerator
(e) dual cycle.
Ans: a

86. The general rule for rating refrigeration systems

(excepting for C02 system) is to approximate following h.p.
per ton of refrigeration
(a) 0.1 to 0.5 h.p. per ton of refrigeration
(b) 0.5 to 0.8 h.p. per ton of refrigeration
(c) 1 to 2 h.p. per ton of refrigeration
(d) 2 to 5 h.p. per ton of refrigeration
(e) 5 to 10 h.p. per ton refrigeration.
Ans: c

87. Reducing suction pressure in refrigeration cycle

(a) lowers evaporation temperature
(b) increases power required per ton of refrigeration
(c) lowers compressor capacity because vapour is lighter
(d) reduces weight displaced by piston
(e) all of the above.
Ans: e

88. Cooling water is required for following equipment in

ammonia absorption plant
(a) condenser
(b) evaporator
(c) absorber
(d) condenser and absorber
(e) condenser, absorber and separator (rectifier).
Ans: e

89. The refrigeration effect in a dry evaporator compared to

flooded evaporator in a similar plant is
(a) same
(b) more
(c) less
(d) more or less depending on ambient conditions
(e) unpredictable.
Ans: c

90. The C.O.P. of a refrigeration cycle with lowering of

condenser temperature, keeping the evaporator
temperature constant, will
(a) increase
(b) decrease
(c) may increase or decrease depending on the type of refrigerant used
(d) remain unaffected
(e) unpredictable.
Ans: a
91. Which of the following refrigerants has lowest freezing
point
(a) Freon-12
(b) NH3
(c) C02
(d) Freon-22
(e) S02.
Ans: d

92. The COP of a vapor compression plant in comparison to

vapor absorption plant is
(a) more
(b) less
(c) same
(d) more/less depending on size of plant
(e) unpredictable.
Ans: a

93. The C.O.P. of a domestic refrigerator in comparison to

domestic air conditioner will be
(a) same
(b) more
(c) less
(d) dependent on weather conditions
(e) unpredictable.
Ans: c

94. The evolution of heat of solution takes place in

ammonia absorption plant when
(a) ammonia vapour goes into solution
(b) ammonia vapour is driven out of solution
(c) lithium bromide mixes with ammonia
(d) weak solution mixes with strong solution
(e) lithium bromide is driven out of solution.
Ans: a

95. The change in evaporator temperature in a refrigeration

cycle, as compared to change in condenser temperature,
influences the value of C.O.P.
(a) more
(b) less
(c) equally.
(d) unpredictable
(e) none of the above.
Ans: a

Refrigeration & Air Conditioning Questions ::

Posted on August 19, 2018 by engineer 5 Comments

300+ TOP BLOCKCHAIN Interview

Questions and Answers →

5 THOUGHTS ON “300+ TOP REFRIGERATION AND AIR

CONDITIONING – MECHANICAL ENGINEERING MULTIPLE
CHOICE QUESTIONS AND ANSWERS”

alpesh nogas
JANUARY 2, 2017 AT 8:26 AM

sir,
plz send me pdf of this question and answer

[email protected]

REPLY

Indrasen Singh
JUNE 5, 2016 AT 2:35 AM

Send me more questions and answers

REPLY

Sadab jalaluddin Shaikh

JANUARY 21, 2016 AT 5:25 AM

Ac and refrigeration

REPLY
 Sadab jalaluddin Shaikh
JANUARY 21, 2016 AT 5:28 AM

Ac and refrigeration

mcq and answers

REPLY

bijoy das
JUNE 15, 2016 AT 2:26 PM

sir thanking you for this question answer

REPLY

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Comment

Name *

Email *

Website
 Post Comment

Engineering interview questions-multiple choice questions-objective type questions-seminor topics-

lab viva questions and answers-online quiz test pdf free download for freshers gate cat syllabus pdf
2019.

Terms & Conditions | Privacy Policy | Contact us | About us