WRITTEN TEST
I. TRUE OR FALSE: Tell whether the statement about Network Design is true
or false. Write (T) if the statement is True and (F) if the statement is False.
Write your answer on a separate sheet.
___________1. Tree topology has a root node and all other nodes are connected
to it forming a hierarchy.
___________2. Hybrid topology is two different types of topologies which is a
mixture of two or more topologies.
___________3. Mesh topology is a point-to-point connection to other nodes or
devices.
___________ 4. In flooding, the nodes have a routing logic, as per the network
requirements.
___________5. In routing, the same data is transmitted to all the network nodes,
hence no routing logic is required.
___________6. A systematic cleaning effort for the entire work area will ensure
the safety of everyone involved.
___________7. Fiber optic cables have many tiny glass particles that are
dislodged when the cables are moved for any reason.
___________8. A simple drink of water can carry glass shards into the throat
and down the esophagus where they can cause
lacerations and internal hemorrhages.
___________9. There are reasons to look through a fiber cable, but care must
be exercised to ensure that there is visible light coming
through the cable.
___________10. Glass shards cannot lodge in the surface of the eye and
cause lacerations.
II. MULTIPLE CHOICE: Read and understand each question. Write your
answer on a separate sheet.
11. It is an electronic device used to verify the electrical connections in a signal
cable or other wired assembly.
a. crimping tool
b. terminal box
c. digital multi-meter
d. LAN tester
12. It is a type of connector commonly used for Ethernet networking.
a. cables
b. pliers
c. rj45
d. screwdriver
13. These are mechanical devices or clips that define a route for one or more
cables along a building wall or within instrumentation, control or other
type of electrical enclosure.
a. clamps
b. cables
c. wire stripper
d. terminal box
14. It is a screwdriver with a wedge-shaped flat tip, used to tighten or loosen
screws that have a straight, linear notch in their heads.
a. flat-head screwdrivers
b. star screwdrivers
c. both a and b
d. none of the above
15. It is a device used to conjoin two pieces of metal by deforming one or both
of them in a way that causes them to hold each other. The result of the
tool's work is called a crimp.
a. wire stripper
b. crimping tool
c. pliers
d. terminal box
II. IDENTIFICATION: Read and understand each question. Write your answer
on a separate sheet.
_______________________ 16. It has an opposite Pin assignments on each end of
the cable.
_______________________ 17. These are used to connect and transfer data and
information between computers, routers, switches, and storage area networks.
_______________________18. These are very much like Straight-Through cables,
the lines are crossed and they are at the opposite positions on either end of the
cable.
_______________________19. It refers to cables that have the same pin
assignments on each end of the cable.
_______________________20. It is identifiable by its hinged or sliding cover that
fully encloses the cables within the channel.
ANSWER KEY
I. TRUE OR FALSE
1. T
2. T
3. T
4. F
5. F
6. T
7. T
8. T
9. T
10. F
II. MULTIPLE CHOICE
11. d
12. c
13. a
14. a
15. b
III. IDENTIFICATION
16. rollover wire cables
17. network cables
18. crossover wired cables
19. straight-through cable
20. latching raceway
Performance Test
Specific Instruction for the Candidate
Qualification Computer System Servicing NCII
Unit of Competency Set-up Computer Networks
General Instruction:
Given the necessary tools, materials, and equipment, you are required to
set-up computer networks with accepted institutional/ industry standard.
(Allotted time: 40 hrs.)
Specific Instruction:
1. Prepare all the tools for network cables installation
2.
2. Set network configuration
3. Set router/Wi-Fi/ wireless access point/repeater configuration
4. Inspect and test the configured computer networks
