#1618 HT
HIGH TEMPERATURE EPOXY COATING
Data Sheet F21
1. PRODUCT NAME Packaging
POLYJECT #1618 HT #1618 HT is available in 3, 15, 150 gallon Kits. Available
in s tock and custom colors.
2. MANUFACTURER
Polygem, Inc. Shelf Life
1105 Carolina Drive Factory sealed containers of this product are guaranteed
West Chicago, IL 60185 to be of first quality for min. 24 months.
Telephone: (630) 231-5600
FAX: (630) 231-5604 Limitations
Internet: www.polygem.com
Not for use on contaminated or oily surfaces.
Do not install when surface temperature is below 40F
3. PRODUCT DESCRIPTION or above 95F.
#1618 HT is a 100% solids, two-component, moisture
insensitive epoxy coating designed to provide protection to During damp and/or cool conditions epoxy will cure
concrete floors in higher temperature environments. #1618 slower and protect finished work from traffic until fully
HT is suitable for use at elevated temps, 180F constant up to cured. Keep from exposure to liquids for 7 days.
300F for intermittent exposure. #1618 HT also offers Consult Polygem Technical staff for additional instructions.
excellent chemical and solvent resistance.
Cautions
Outstanding Features Wear chemical goggles, proper protective clothing and
High Temperature Resistant gloves to prevent direct contact of resins. Consult
No VOC’s or Solvents Material Safety Data Sheet for full listing protective
requirements.
100% solids
#1618 HT may irritate eyes and skin. Avoid contact with
Chemical and Solvent Resistant
eyes or prolonged contact with skin.
Excellent Adhesion to concrete, wood, fiberglass and Keep out of reach of children.
metal surfaces.
Uses
5. TECHNICAL DATA
For protecting floors and walls subject to elevated Performance Properties with Test/Test Method Results
temperature such as:
Steam tunnels Pot Life @ 77F (100 grams) 35 mins.
Commercial Kitchens Thin Film Set-Time @ 77F 4 hours
Foundries and Mills Full Cure time @ 77F 24 hours
Slant Shear ASTM C-882 1,300 psi min
Sludge and slurry tanks
Compressive Strength ASTM D-695 13,100 p.s.i.
4. APPLICATION INSTRUCTIONS Tensile Strength 8,115 p.s.i.
Tensile Elongation ASTM D-638 2.0% min.
1) Mix 2 parts A (Resin) to 1 part B Hardener) by volume.
Linear Coefficient of Shrinkage <0.001
Avoid mixing more than what can be applied in 35
minutes.. Heat Deflection Temperature >200F
2) Stir with a mixing stick or slow speed drill with a mixing Shore D Hardness 80-75
paddle for 1-2 minutes until streak free and uniform in Water Absorption, 24 hours 0.105%
color. Scrape sides and bottom of mixing pail during Mixed Viscosity 200 cps
mixing and do not over mix more than 3 minutes. Avoid Mix Ratio 2:1
whipping air into mixture.
3) Apply mixed material and do not leave mixed material in
mixing bucket.
4) Clean up any uncured epoxy with #20 or equivalent
solvent.
Polygem, Inc. warrants its products to be free of manufacturing defects and that, at the time and place of shipment, our material will meet current physical properties when applied within
Polygem’s directions and tested in accordance with ASTM and Polygem standards. Polygem, Inc’s liability is limited to replacement of material found defective. As Polygem, Inc. has no
control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and/or our information is valid in a
particular circumstance. Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each product. Nothing contained
herein shall be construed to be a recommendation to use or as a license to operate under or to infringe any existing patents.
F21 1 1/10/19
Data sheets are subject to change without notice, for latest revision check our website at www.polygem.com
