POLYBAC #1325

BRUSHABLE CERAMIC EPOXY COATING

Data Sheet M-024

1. PRODUCT NAME 3) Spread mixed epoxy with trowel or putty knife

POLYBAC #1183-WB and worked well into the surface.
4) Epoxy may be smoothed with a trowel dipped in
2. MANUFACTURER a solvent.
Polygem, Inc.
1105 Carolina Drive Packaging
West Chicago, IL 60185 POLYBAC #1325 is available in 2 kit sizes: 4 lb. Quart Kits
Telephone: (630) 231-5600 and 10 lb. Gallon Kits. Larger kits are available.
FAX: (630) 231-5604
Internet: [Link] Color
Available in standard Gray or Black
3. PRODUCT DESCRIPTION
POLYBAC #1325 is a brushable epoxy coating specially Shelf Life
blended with abrasion resistant ceramic fillers to provide a Factory sealed containers of this product are guaranteed
durable barrier to protect surfaces subjected to wear and to be of first quality for min. 12 months.
abrasion. POLYBAC #1325 is easy and apply by brush to
most surfaces. POLYBAC #1325 is waterproof and resistant Limitations
to most chemicals and solvents. POLYBAC #1325 is a thick Do not apply over 1/4” thick per layer. Additional
and creamy epoxy coating will allow for vertical and thickness can be built up with multiple coats. Allow prior
overhead application. coat to harden to touch before the application of the next
layer.
Advantages Not for use on wet or oily surfaces.
Extremely durable ceramic matrix. Do not install when surface temperature is below 45F
Chemical Resistant (7C) or above 90F (32C.
No VOC’s or Solvents During cool conditions epoxy will cure slower, protect
Low Odor Formula finished work from wear and abrasion until fully cured.
Bonds to most dry surfaces
Cautions
Uses Wear chemical goggles and NIOSH approved respirator.
For the protection of metal or concrete surfaces that are Wear proper protective clothing and gloves to prevent
exposed to abrasive environments. POLYBAC #1325 is direct contact of resins. Consult Material Safety Data
ideal for use on: Sheet for full listing protective requirements.
POLYBAC #1325 may irritate eyes and skin. Avoid
 Pipe Elbows contact with eyes or prolonged contact with skin.
 Mixing vessels For professional use only.
 Cyclones Keep out of reach of children.
 Hopper and Chutes
 Pump Casings 5. TECHNICAL DATA
 Wear Plates Performance Properties
 Brick Corners and Transitions Areas Test/Test Method Results
 Dust Collection Systems
 Chipper and Grain Bins Pot Life @ 77F (100 gms) 45 mins.
 Pneumatic Conveyors Compressive ASTM D-695 10,900 psi
 Heat Exchangers and Tube Sheets Tensile Strength ASTM D-638 4,950 psi
 Augers, Fan and Impeller Blades Elongation ASTM D-638 1% min.
Bond Strength ASTM C-882 1,950 psi
4. APPLICATION INSTRUCTIONS Shore D Hardness 85-80
1) Clean surface by sandblasting or grinding to Cure Time @75 F 16-24 hours
provide rough white-metal profile. Mix ratio by volume A/B 3:1
2) Thoroughly mix 3 parts by volume of Part A Resin Mixed Viscosity Heavy Cream
with one part of Part B Hardener until streak free. Color Mixed Gray
Mix only enough that can be applied in 45 minutes.

Polygem, Inc. warrants its products to be free of manufacturing defects and that, at the time and place of shipment, our material will meet current physical properties when applied within
Polygem’s directions and tested in accordance with ASTM and Polygem standards. Polygem, Inc’s liability is limited to replacement of material found defective. As Polygem, Inc. has no
control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and/or our information is valid in a
particular circumstance. Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each product. Nothing contained
herein shall be construed to be a recommendation to use or as a license to operate under or to infringe any existing patents.

POLYBAC #[Link]/Rev. 1/1/07

Data sheets are subject to change without notice, for latest revision check our website at [Link]