Catalogue HY30-8200/UK Truck Hydraulics

Technical Information F1 Pump - Fixed Displacement

F1-25 to -101, ISO

Specifications
F1 frame size 25 41 51 61 81 101
Displacement [cm 3/rev] 25.6 40.9 51.1 59.5 81.6 102.9
Max flow 1) [l/min]
at 350 bar 67 98 112 131 1633) 1853)
at 400 bar 56 86 97 113 143 160
Max operating pressure [bar]
continuous
intermittent
350
400
350
400 3
Shaft speed [rpm]
- short circuited pump (low press.) 2700 2700 2700 2700 2300 2300
- max speed at 350 bar 2) 2600 2400 2200 2200 2000 3) 18003)
at 400 bar 2) 2200 2100 1900 1900 1750 1550 3)
Torque 1) [Nm]
at 350 bar 142 227 284 331 453 572
at 400 bar 163 260 324 378 518 653
Input power [kW]
- continuous 31 46 52 61 76 86
- intermittent 4) 39 57 66 76 95 108
Weight [kg] 8.5 8.5 8.5 8.5 12.5 12.5
1) Theoretical values
2) Valid at an inlet pressure of 1.0 bar (abs.) when operating
on mineral oil at a viscosity of 30 mm 2/s (cSt).
3) Valid with 2 1/2" inlet (suction) line.
With 2" suction line: F1-81 – max 1400 rpm (Q y120 l/min);
F1-101 – max 1000 rpm (Qy120 l/min).
4) Max 6 seconds in any one minute.
NOTE: For noise level information, contact Parker Hannifin

Pump cross section

1 2 3 4 5 6 7 8 9
1. Input shaft 4. Housing 7. Piston with piston ring
F1_stor_section_06-[Link]
2. Bearings 5. Timing gear 8. Cylinder barrel
3. Shaft seals 6. Barrel support 9. End cap

15 Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Catalogue HY30-8200/UK Truck Hydraulics
Technical Information F2 Twin-flow Pump - Fixed Displacement

F2 Twin-flow Pump

Contents Page Chapter

Pump and Line selection ..............................................................................10 ................. 2

Specifications ...............................................................................................28

Installation dimensions .................................................................................29

Ordering code ...............................................................................................29

Standard versions.........................................................................................29

Suction fittings ..............................................................................................44 ................. 9

Installation and start up ................................................................................61 ............... 12

27 Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Catalogue HY30-8200/UK Truck Hydraulics
Technical Information F2 Twin-flow Pump - Fixed Displacement

Specifications
Frame size F2- 42/42 53/53 55/28 70/35
‘Left hand’ and ‘right hand’ end caps
Displacement [cm 3/rev]
Port A 43 54 55 69 Outher pressure A
Port B 41 52 28 36 port (A)
Max operating pressure [bar] Inlet (suction)
continuous 350 350 350 350 port
intermittent 400 400 400 400
Inner pressure
Max shaft speed [rpm] port (B)
B F2

(unloaded pump; low pressure) 2550 2550 2550 2550

End cap for right hand rotating pump
Max selfpriming speed [rpm]
Ports A1) 2) and B 1) 2) pressurised 1800 1800 1800 1800
Port A 2) unloaded, pressure in port B 2100 2100 2100 2100 Outher pressure
F2 A
port (A)
Input power [kW]
Max intermittent3) 100 126 100 126 Inlet (suction)
port
Max continuous 88 110 88 110
Weight [kg] 19 19 19 19 Inner pressure
port (B) B

1) Valid with 2 1/2" inlet (suction) line;

with 2 " inlet line: 53/53 and 70/35 max 1 100 rpm End cap for left hand rotating pump
42/42 and 55/28 max 1400 rpm. (qy120 l/min)
2) Measured at 1.0 bar abs. inlet pressure.
Please note: A lower inlet pressure affects pump performance.
3) Max 6 seconds in any one minute.

Flow vs. shaft speed (theoretical)

Pump speed [rpm] 800 1000 1200 1400 1600 1800 1900 2000 2100
F2-53/53 flow [l/min]
Port A 43 54 65 76 86 97 - - -
Port B 42 52 62 73 83 94 99 104 109
Total (ports A + B) 85 106 127 149 169 191 - - -
Note: 42/42 values is 80% of 53/53 values
F2-70/35 flow [l/min]
Port A 55 69 83 97 110 124 - - -
Port B 29 36 43 50 58 65 68 72 76
Total (ports A + B) 84 105 126 147 168 189 - - -
Note: 55/28 values is 80% of 70/35 values

Shaft torque vs. pressure (theoretical)

Pressure [bar] 150 200 250 300 350
F2-53/53 torque [Nm]
Port A 129 171 214 257 300
Port B 124 165 206 248 289
Total (ports A + B) 253 336 420 505 589
Note: 42/42 values is 80% of 53/53 values
F2-70/35 torque [Nm]
Port A 164 219 274 329 383
Port B 86 114 143 171 200
Total (ports A + B) 250 333 417 500 583
Note: 55/28 values is 80% of 70/35 values

28 Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden
Catalogue HY30-8200/UK Truck Hydraulics
Technical Information F2 Twin-flow Pump - Fixed Displacement
81
Installation dimensions Outlet (pressure) 51 Inlet (suction)
port (BSP 3/4”) port

B F2

80 Right hand rotation

109

Left hand rotation

213 81
109 74 51

18
169 5
Approx.
center of
gravity
B

40°
Inspection
port 262
277 (plugged)
243

127
119
15
12

55
27.8 8.5 Drain hole
(between
shaft seals)
1.85 +0.3/-0 Ø33 +0/-0.1 M12x24
Spline B8x32x36 Ø34.9 148
(DIN 5462) Ø80 (+0/-0.013)

Ordering code Standard versions NOTE:

Designation Ordering no. - Before start-up, tighten
Example: F2 - 53/53 - L the inspection port plug
F2-42/42-R 378 4042 to 70–100 Nm.
Frame size [cm3/rev] F2-42/42-L 378 4043 - To change the direction
42/42 of rotation, the end cap
F2-53/53-R 378 1453 must be replaced.
53/53 F2-53/53-L 378 1454
55/28
70/35 F2-55/28-R 378 4128 NOTE: The F2 pump does not
Direction of rotation F2-55/28-L 378 4129 include a suction fitting;
L Left hand F2-70/35-R 378 1470 it must be ordered
R Right hand F2-70/35-L 378 1471 separately. See chapter 9.

29 Parker Hannifin
Pump and Motor Division
Trollhättan, Sweden