Testing of Mine Protection
Boots
Ian Horsfall, Damaris Nicol, Ryan Pinto
[email protected]
• Reasons for studying mine boots
• The art of the possible
• Test methods
• Previous work
• Future research
Applications
• Main requirement has been from humanitarian
demining
• Continuing interest from combat troops and
particularly EOD / search units
• Note that -
– on flat smooth ground vehicles tend to be used
– mine resistant boots are cumbersome
– protection is at best limited
• Result
– If there are mines then stay in vehicle
– If there aren't then why wear boots
The effect of a small blast
Desert boot
36g PE4 charge
60mm burial depth
35kg mass
Blast Mine Tests Against Footwear
• Frangible or mechanical surrogate with suitable damage
assessment method
• Mine surrogate consisting of C4 or PE4 explosive packed in
cylindrical containers with prescribed detonation point
• Charge buried in dry medium sand
• Test rig required for guiding the motion of the surrogate vertically
• Defined total reaction mass of the surrogate and guidance system
• Zero preload applied on the soil.
TR-HFM-089 Test Methodologies for Personal Protective
Equipment Against Anti-Personnel Mine Blast
Surrogates
Frangible Surrogate Limb (FSL) ‘Mechanical’ surrogates
(Adelaide T&E Systems/SJH Projects) DRDC illustrated above
One time use Reusable
Well validated Instrumented
Can be instrumented Requires a transfer function
Typically assessed by medics Relatively cheap
Fairly expensive
Injury mechanisms
• Fracture • Good agreement with FSL,
– Fracture to heel and long – Also assessed by peak load
bones – Suppressed by standoff
• Compressive failure of • Observed on FSL
heel and foot – Loading case less well
– Bursting of foot due to understood
compressive loads – Suppressed by standoff
• Flesh stripping • Difficult to reproduce
– Gas driven up through leg – Only observed in cadavers
– Requires boot to be intact
Cranfield Trials
• Four boot types tested
– Three combat boots and one commercial mine
resistant boot
• Drop tower impact tests
– 1ms-1-8ms-1 impact tests to allow calibration of
instrumentation and some assessment of boot
behaviour
• Explosive tests
– Tests using 50g and 35g buried charges to
investigate trials methods, effects of burial and boot
failure processes
Desert boot Matterhorn boot ‘Combat’ boot
Drop tower layout
Displacement
gauge
Striker load cell
Striker
Anvil load cell
(used for
blast tests)
Drop tower results
Peak displacement Peak impulse Peak Force
Boot type
(mm) (Ns) (kN)
AP-mine boot 27.8 19.1 3.5
Combat boot 16.5 18.3 6.1
Matterhorn
14.0 18.5 8.0
boot
Desert boot 20.7 19.2 6.4
Impact tests at 5.5ms-1
Thick sole boots have lower forces and higher displacement
Impulse is the same for all cases (Drop weight momentum = 19.8Nm)
Blast tests
35 kg mass on top
of rig
Rig support, LVDT
secured by
ratchet straps Accelerometer
and placed on
concrete blocks
Load cell
AP-mine
boot
Container filled with
kiln dry sand
50g charge tests
Depth of
Peak force Peak displacement
Firing burial Damage
(kN) (mm)
(mm)
1 0 145 42 BD3
5 0 115 20 BD3
2 20 150 33 BD3
6 20 120 16 BD3
3 40 145 34 BD3
4b 60 100 NA BD3
Boot
damage Description of damage levels
level
Minor damage to boot (i.e. portion of sole blown off,
BD1
insole destruction)
Structural damage to boot (i.e. minor blast penetration
BD2
into foot compartment of boot)
Breach (i.e. massive blast penetration into foot
BD3
compartment of boot)
35g charge tests
Peak
Type of boot Depth of Boot Damage
Firing Peak force (kN) displacement
used burial (mm) level
(mm)
1 AP-mine 0 68 NA BD3
3 AP-mine 20 79 30. BD3
5 AP-mine 30 47 24 BD2
4 AP-mine 40 43 22 BD2
2 AP-mine 60 44 14 BD1
6 Matterhorn boot 60 48 9.4 BD3
7 Desert boot 60 45 11 BD2
8 Combat boot 60 42 10 BD2
For AP mine boot, damage reduces from catastrophic to minor as burial depth increases
In all cases peak force was much greater than typical tibia strength (5.4kN)
Future work
• New test rig under construction
• Investigate boot failure
• Investigate peripheral aspects of
protection such as fragmentation and
damage to the un-impacted leg
• Deliver a cheap sorting method for
development purposes
Summary
• Providing practical mine resistant footwear
is very challenging
• Test methods are still underdeveloped
• The link between loading, boot design and
surgical outcome needs improvement
