Scribd
Upload
152 views1 page

Compound Specification Sheet: CSP-938 Diesel Grade, Vinyl Ester, Gray SMC

This document provides the specifications for a diesel grade vinyl ester compound called CSP-938. It lists the typical properties of the compound such as a specific gravity of 1.72, glass percentage of 30%, water absorption of less than 0.35%, and heat distortion temperature of over 450 degrees Fahrenheit. It also provides flexural strength, tensile strength, mold shrinkage, and coefficient of expansion values. Typical applications for this compound include parts requiring high strength at room temperature and corrosion resistance for diesel engine external body parts.

Uploaded by

Brian García Aguirre
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
152 views1 page

Compound Specification Sheet: CSP-938 Diesel Grade, Vinyl Ester, Gray SMC

This document provides the specifications for a diesel grade vinyl ester compound called CSP-938. It lists the typical properties of the compound such as a specific gravity of 1.72, glass percentage of 30%, water absorption of less than 0.35%, and heat distortion temperature of over 450 degrees Fahrenheit. It also provides flexural strength, tensile strength, mold shrinkage, and coefficient of expansion values. Typical applications for this compound include parts requiring high strength at room temperature and corrosion resistance for diesel engine external body parts.

Uploaded by

Brian García Aguirre
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

COMPOUND SPECIFICATION SHEET

CSP-938
Diesel Grade, Vinyl Ester, Gray SMC
ASTM Test Typical Molded Metric
Property Method Specification Equivalent

Specific Gravity D-792-98 1.72 1.72


Glass Percentage 30%
Water Absorption
(24 Hours @ 23°C) D-570-98 <0.35% <0.35%
Heat Distortion Temp.
°F, 264 PSI D-648-98 >450°F >235°C
Barcol Hardness D-2583-95 45 - 60 45 - 60
Impact Strength (Izod
Ft. Lbs./In. Notched) D-256-97 14 - 18 745 - 960 J/m
Flexural Strength, PSI D-790-98 22,000 - 26,000 150 - 180 MPa
Flexural Modulus
(PSI x 106) D-790-98 1.2 - 1.6 8.2 – 11.0 GPa
Tensile Strength, PSI D-638-98 9,000 - 12,000 62 - 83 MPa
Mold Shrinkage (Cold
Piece -- 0.0005 0.0005 cm/cm
from Cold Mold,
In./In.)
Coefficient of Expan- D-696-98 9.7 x 10-6 17.5 x 10-6
sion in./in./°F cm/cm/°C
(75°F - 300°F)

TYPICAL APPLICATIONS:

Parts requiring high strength at room temperature, good retention of properties at high temperatures and cor-
rosion resistance, some UV resistance, such as diesel engine external body parts.

Rev: April, 2010

Data presented herein is based upon tests performed in our labs on properly molded flat sheets tested according to standard procedures where referenced and what we believe to be appropriate methods where no standard
method exists. Since the values found in parts made from this material depend upon many factors beyond our control, such as molding conditions and procedures, part and mold design, operator skill and specific test
procedures employed, we do not guarantee that the specified results will be obtained on any specific part and urge prospective users to make their decisions based upon the performance of actual parts molded under
production conditions. NO WARRANTY OR MERCHANTABILITY OR FITNESS FOR PURPOSE IS GIVEN. Our liability and purchaser’s remedy for any fault in the product, whether the result of negligence or
otherwise, is limited to a refund of the cost of the material. This printed copy of this document is only for reference purposes and is the responsibility of the user to verify the accuracy of this document against the master
list.

ThyssenKrupp Budd Company • 1515 Atlantic Blvd. • Auburn Hills, Michigan 48326 • 248-391-2880

You might also like