SIZE A1 840 x 594

1420 ( Casting plate ) SECTION B-B SECTION C-C

SCALE 1 : 5 SCALE 1 : 2
1370 ( Upper tapered plate )

26 mini
a=14 15

a=14

295,5
17

C C
16

see detail 2
a=3
1160 ( lower masonry plate )

NOTE :

LONGITUDINAL AXIS
-FOR THE DETAIL OF PRESET OF SLIDING PLATE AND UPPER
TAPERED PLATE SEE THE DRAWING STUS16053
-FOR THE DETAIL OF CAST IN PLATE SEE DRAWING STUS16065
-FOR THE DETAIL OF LOWER MASONRY PLATE SEE DRAWING
STUS16064
DETAIL 2
SCALE 1 : 1.5 22 -FOR ITEM 3 SEE DRAWING PDA005
1680 ( Upper tapered plate )

Pos. Pcs Description Dimension Material Standard Note

1930 ( Casting plate )

DETAIL 1 1 1 Cast in plate 1930x1420x20 S355J0 EN 10025 P

SCALE 1 : 1

14 x 110 = 1430
7 x x220 = 1540
2 50 Stud n 22x100 S235J263+C450 - -

4 x 220 = 880
A A Upper tapered plate
3 1 1680x1370x26mini S355J0 EN 10025 P

1070
Detail fuse bolts (slope)
Failure diameters 22.3mm 4 2 Lateral guide 1680x90x64 S355J0 EN 10025 P
20 H.FAILURE 2250kN 5 1 Sliding plate 1680x1180x86 S355J0 EN 10025 P
6 26 Fuse screw M27x110 Cl 10.9 ISO 4762 H
F 7 16 Upper screw M27x70 Cl 10.9 ISO 4017 H
21
8 16 Upper washer d27 Grade A ISO 7089 H
F 9 16 Upper anchor plate 120x80x40 S355J0 EN 10025
10 1 Antifriction disc n 800x6 PTFE EN 1337-2 1
23 11 1 Reversal basement 990x990x116 S355J0 EN 10025 P
12 1 Piston n 789x37 - n 705x29 S355J0 EN 10025 P
13 1 Piston support - base 1150x990x43 S355J0 EN 10025 P
14 1 Lower masonry plate 1160x1000x33 S355J0 EN 10025 P
Cl 10.9
15 12 Lower screw M30x120 ISO 4017 H
11 24 galva.
Grade B
16 12 Lower domed nut M30 NF 27-453 H
galva.
Grade A
17 24 Lower washer d30 ISO 7089 H
galva.
Lateral stainless
18 2 1630x30x2 X5CrNiMo17-12-2 EN 10088-2 P
10 steel
Lateral Antifriction
19 2 990x20x2,5 CM1 EN 1337-2 -
sheet
20 1 Upper stainless steel 1670x925x2 X5CrNiMo17-12-2 EN 10088-2 -
Natural 50
21 1 Rubber disc n 790x53 EN 1337 2
shores A
22 1 Scraping joint 10x10 E.P.D.M. FPC -
23 3 Antiextrusion seal 10x1,5 CuZn37 EN 12163 -
24 1 F.O.A.M. seal 15x15 E.P.D.M. FPC -
25 4 Temporary fixing plate L 100x50x8 - 120 S355J0 EN 10025 P
26 16 Temporary screw M10x30 Cl 10.9 ISO 4017 H
2
27 16 Temporary washer M10 Grade A ISO 7089 H
6 Note - 1 VIRGIN 1° USE WITH CAVITIES AND GREASE Molykote PG21

Note - 2 HARDNESS SHORE A50 5

4x 220 = 880 1 Note - P PROTECTION ANTI-CORROSION - CORROSION PROTECTION
5 x 180 = 900
1090
1260 5
TECHNICAL DATA
LOAD - ULS ( kN ) LOAD - ULS SEISMIC ( kN ) MOV.
B
ROT.

TRANS.

TRANS.

TRANS.
LONG.

LONG.
VERT.

VERT.

Long.

VERT.

VERT.

Long.
TYPE POS Qu.

Max

Max

Max
Min

Min

Min
(Rad.)

3 V17L-P4-R 22000 8500 790 - 12480 8720 1660 - -240 330 - 0,01 1
V17R-P4-R 21800 8400 740 - 12290 8710 1560 - -240 335 - 0,01 1
V17L-P5-R 22000 8700 860 - 12370 9030 2010 - -270 345 - 0,01 1

9 V17R-P5-R 21700 8600 820 - 12110 8910 1930 - -270 340 - 0,01 1
GGL
V17L-P6-R 22000 8600 890 - 13190 8210 2250 - -290 340 - 0,01 1
14 13 V17R-P6-R 21800 8600 860 - 12700 8460 2180 - -285 335 - 0,01 1
8 V17L-P11-R 22000 8600 810 - 13110 8290 1810 - -340 280 - 0,01 1
V17R-P11-R 21800 8400 840 - 13480 7780 1910 - -330 270 - 0,01 1
7
295,5

AFFAIRE NUMERO
F 21.12.15 PCI ARA PSN MODIFIED ITEM 7, 9
PROJECT FREYSAS NUMBER R14-087E1
see detail 1 E 28.05.15 PCI ARA PSN GENERAL MODIFICATION
DOSSIER NUMERO
D 30.04.15 WMI ARA PSN MODIFIED QUANTITY OF ITEM 2
FILE KMO-ILM VIADUCT V17 NUMBER .
C 24.04.15 WMI ARA PSN MODIFIED ITEM 16

B 21.04.15 WMI ARA PSN MODIFIED ITEM 1 & NOTE, ADDED WELDING & SECTION C-C
DESIGNATION
GGL 22400_2250_630
DESIGNATION
A 09.04.15 WMI ARA PSN FIRST DIFFUSION
FREYSSINET INTERNATIONAL & COMPAGNIE FORMAT/SIZE ECHELLE/SCALE
B INDICE DESSINE VERIFIE APPROUVE
REV.
DATE
DRAWN CHECKED APPROVED
MODIFICATIONS 280 AVE NAPOLEON BONAPARTE TEL. : (33.1) 47 76 79 79
A1 1/4
92506 RUEIL MALMAISON CEDEX FAX : (33.1) 47 76 78 93
1000 ( lower masonry plate ) MATIERE TRAITEMENT MASSE / MASS (kg) ( FRANCE )
MATERIAL S355J0 TREATMENT C4V NV 695
3850kg REPRODUCTION ET MODIFICATION INTERDITES COPYRIGHT & MODIFICATION RESERVED
R14-087E1_PEA005 F FEX
10 20 30 40 50 60 70 80 90 100 mm