Scribd
Upload
212 views1 page

Yokohama Fabric Belt Specification PT - INALUM/Indonesia: OR#300 NN-100 1050X4PX5.0X2.0 Belt Description

This document provides specifications for a fabric belt for PT. INALUM/Indonesia. The belt has a width of 1050mm +/- 10.5mm, is made of 4 plies of nylon fabric with a minimum tensile strength of each ply of 100kN/m. It has top and bottom covers of rubber grade OR#300 that are 5.0mm and 2.0mm thick respectively. The document outlines dimensional tolerances and material properties including tensile strength, elongation, hardness, and adhesion values that the belt is required to meet.

Uploaded by

Eky Haryans
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
212 views1 page

Yokohama Fabric Belt Specification PT - INALUM/Indonesia: OR#300 NN-100 1050X4PX5.0X2.0 Belt Description

This document provides specifications for a fabric belt for PT. INALUM/Indonesia. The belt has a width of 1050mm +/- 10.5mm, is made of 4 plies of nylon fabric with a minimum tensile strength of each ply of 100kN/m. It has top and bottom covers of rubber grade OR#300 that are 5.0mm and 2.0mm thick respectively. The document outlines dimensional tolerances and material properties including tensile strength, elongation, hardness, and adhesion values that the belt is required to meet.

Uploaded by

Eky Haryans
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

YRC Ref. No. CBQ190371, Date 2019. 7.

16
Yokohama Fabric Belt Specification Digitally signed by Eky
Haryan Saputra

[Link]/Indonesia Eky DN: cn=Eky Haryan


Saputra gn=Eky Haryan
Saputra c=ID Indonesia

Haryan l=ID Indonesia o=PT.


STOMIL INDONESIA
e=[Link]@stomilin
Saputra [Link]
Reason: I am the author
of this document
Location:
Date: 2019-10-02
Prepared by : [Link]
15:47+07:00
Examined by: [Link]
Approved by: [Link]
OR#300 NN-100
BELT DESCRIPTION
1050X4PX5.0X2.0
Applicable
DESCRIPTION Unit Standard for CHINA ORIGIN
Testing
I. BELT DIMENSION
1.1 Belt Width & tolerance mm JIS K 6322 1050 ±10.5
1.2 Belt length & tolerance % JIS K 6322 +2.5%, -0

Nominal 9.9 mm
1.3 Total belt thickness & tolerance mm JIS K 6322 Variation in any one belt shall be not
more than 1.0mm.

1.4 Thickness top cover & tolerance mm JIS K 6322 5.0 +Free, -0.25
1.5 Thickness bottom cover & tolerance mm JIS K 6322 2.0 +Free, -0.2
1.6 Number of ply Nos - 4
1.7 Belt edge rubber width mm YRC STD 15 ±10
II. CARCASS FABRIC PROPERTIES
2.1 Fabric material - - Nylon-Nylon
2.2 Tensile strength of belt carcass, minimum kN/m/ply JIS K 6322 100
2.3 Elongation at 10% of tensile strength, maximum % JIS K 6322 4
III. COVER RUBBER PROPERTIES
3.1 Cover rubber grade - - OR#300
3.2 Tensile strength, minimum MPa JIS K 6322 12.0
3.3 Elongation at break, minimum % JIS K 6322 350

3.4 Tensile strength after ageing(70℃X96hours) % JIS K 6322 10.0

3.5 Elongation at break after ageing(70℃X96hours) % JIS K 6322 300

3.6 Hardness - JIS K 6253 55～70


3
3.7 Maximum abrasion loss mm JIS K 6322 250
Change rate of tensile strength after oil Not change by more than -35%
3.8 % JIS K 6258
immersion (40℃X168hours OIL:IRM903) from original value
Change rate of elongation at break after oil Not change by more than -30%
3.9 % JIS K 6258
immersion (40℃X168hours OIL:IRM903) from original value
Change rate of volume after oil immersion Not change by more than ±15%
3.10 % JIS K 6258
(40℃X168hours OIL:IRM903) from original value
IV. ADHESION
AVERAGE
4.1 Top cover to Ply kN/m JIS K 6322 2.4
4.2 Ply to Ply kN/m JIS K 6322 2.4
4.3 Ply to Bottom cover kN/m JIS K 6322 2.0
Minimun
4.4 Top cover to Ply kN/m JIS K 6322 1.6
4.5 Ply to Ply kN/m JIS K 6322 2.0
4.6 Ply to Bottom cover kN/m JIS K 6322 1.6

You might also like