Grand Summary

PROJECT :- CONSTRUCTION OF OFFICE BUILDING FOR DENTAL COUNCIL OF INDIA AT RK PURAM, NEW DELHI
GRAND SUMMARY

Amount (Rs.) as per Amount (Rs.) as per

S.No. DESCRIPTION
DSR-2018 item Non- Scheduled item

1 CIVIL WORK OFFICE 12,15,31,453.83 4,37,14,891.29

2 GUARD ROOM & GATE 571033.49 172806.00
3 BOUNDARY WALL 3095201.56 0.00
4 RAIN WATER HARVESTING 619914.51 0.00
5 HVAC 8664894.28 9449416.00
6 INTERNAL ELECTRICAL 6426760.00 12907664.31
7 EXTERNAL ELECTRICAL 768866.00 19361487.12
8 PLUMBING 721104.90 8245926.40
9 FIREFIGHTING 3224028.00 2579826.64
SUB TOTAL (A) 145623256.57 96432017.77
ADJUSTED VALUE WITH REFERENCE TO DSR-2018 145623256.57 94824817.47
Estimated Cost put to Tender 240448074.04

2404.48
In Lac

Note:
1 The cost index for DSR 2018 is 118 with reference to CPWD Plinth Area Rates 2012
2 Latest Cost Index with reference to CPWD Plinth Area Rates 2012 as on 01.04.2019 is 120.

Page 1 of 1
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

OFFICE (2B+S+5), BOQ - CIVIL WORKS

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic
excavator)/manual means over areas (exceeding 30 cm in depth,
1.5 m in width as well as 10 sqm on plan) including getting out
1 2.6 and disposal of excavated earth lead upto 50 m and lift upto 1.5
m, as directed by Engineer-in-charge.

i 2.6.1 All kinds of soil. Cu.Mt. 8892.00 181.85 1617010.20

Earth work in excavation by mechanical means (Hydraulic
excavator)/ manual means over areas (exceeding 30 cm in
depth, 1.5 m in width as well as 10 sqm on plan) including
2 2.7 getting out and disposal of excavated earth lead upto 50 m and
lift upto 1.5 m, as directed by Engineer-incharge.

i 2.7.1 Ordinary rock Cu.Mt. 754.00 352.45 265747.30

Excavating trenches of required width for pipes, cables, etc
including excavation for sockets, and dressing of sides, ramming
of bottoms, depth upto 1.5 m, including getting out the
excavated soil, and then returning the soil as required, in layers
not exceeding 20 cm in depth, including consolidating each
3 2.10.1
deposited layer by ramming, watering, etc. and disposing of
surplus excavated soil as directed, within a lead of 50 m : All
kinds of soil.

i 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. Metre 48.00 223.00 10704.00
Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300
ii 2.10.1.2 Metre 48.00 364.20 17481.60
mm dia
Pipes, cables etc. exceeding 300 mm dia but not exceeding 600
iii 2.10.1.3 Metre 64.00 568.60 36390.40
mm
Extra for excavating trenches for pipes, cables etc. in all kinds of
soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is
iv 2.11 Metre 64.00 722.12 46215.81
over corresponding basic item for depth upto 1.5 metre).

Close timbering over areas including strutting, shoring and

4 2.18 packing cavities (wherever required) etc. complete.
(Measurements to be taken of the face area timbered) :
i 2.18.1 Depth not exceeding 1.5 m Sq.Mt. 181.53 116.25 21102.86
ii 2.18.2 Depth exceeding 1.5 m but not exceeding 3 m Sq.Mt. 181.53 129.75 23553.52
iii 2.18.3 Depth exceeding 3 m but not exceeding 4.5 m Sq.Mt. 181.53 143.90 26122.17
Open timbering over areas including strutting, shoring and
5 2.22 packing cavities (wherever required) etc. complete.
(Measurements to be taken of the face area timbered) :
i 2.22.1 Depth not exceeding 1.5 m Sq.Mt. 181.53 40.90 7424.58
ii 2.22.2 Depth exceeding 1.5 m but not exceeding 3 m Sq.Mt. 181.53 48.45 8795.13
iii 2.22.3 Depth exceeding 3 m but not exceeding 4.5 m Sq.Mt. 181.53 60.70 11018.87
6 2.24 Extra rates for quantities of works, executed :
In or under water and/or liquid mud, including pumping out Metre
i 2.24.1 3086.80 18.08 55809.27
water as required. Depth
Filling available excavated earth (excluding rock) in trenches,
plinth, sides of foundations etc. in layers not exceeding 20cm in
7 2.25 depth, consolidating each deposited layer by ramming and Cu.Mt. 3226.34 219.65 708666.15
watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in. All kinds
8 2.26.1
of soil
i i 1.50-.3.00m Cu.Mt. 2022.83 90.40 182864.06
ii ii 3.00-.4.50m Cu.Mt. 2009.38 180.80 363296.08
iii iii 4.50-.6.00m Cu.Mt. 1619.29 271.20 439150.77
iv iv 6.00-.7.50m Cu.Mt. 1619.29 361.60 585534.36
v v 7.50-.9.00m Cu.Mt. 1018.91 452.00 460549.52
vi vi 9.00-.10.50m Cu.Mt. 289.11 542.40 156815.92
vii vii 10.50-.12.0m Cu.Mt. 159.48 632.80 100918.07
Disposal of excavated excess earth away from the site including
conveyance of materials up to an average lead of 5KM away
from the site, and correspondiong required lift, loading,
unloading etc complete as directed by the Engineer-in-charge.
9 1.1.2 (The quantity is net quantity of capacity of truck after deduction
of 20% for looseness)(considering the maximum disposal
location at 5 KM distance)

By mechanical transport including loading, unloading and

i 1.1.2 (8) Cu.Mt. 6419.66 201.83 1295679.46
stacking. (Lead upto 5KM away from the site)

BOQ Civil Works Page 1 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Supplying and filling in plinth with sand under floors, including

10 2.27 watering, ramming, consolidating and dressing complete. Cu.Mt. 62.96 1953.05 122960.12

Surface dressing of the ground including removing vegetation

and inequalities not exceeding 15 cm deep and disposal of
11 2.28
rubbish, lead upto 50 m and lift upto 1.5 m.

i 2.28.1 All kinds of soil Sq.Mt. 1594.80 24.35 38833.48

Supplying chemical emulsion in sealed containers including
12 2.34 delivery as specified.
Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
i 2.34.1 litre 678.48 200.85 136272.76
Anti termite treatment
Diluting and injecting chemical emulsion for POST-
13 2.35 CONSTRUCTIONAL anti-termite treatment (excluding the cost of
chemical emulsion) :
Along external wall where the apron is not provided using
chemical emulsion @ 7.5 litres / sqm of the vertical surface of
the substructure to a depth of 300mm including excavation
i 2.35.1.1 channel along the wall & rodding etc. complete: With Metre 240.27 28.25 6787.63
Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion

@ one litre per hole, 300 mm apart including drilling 12 mm
diameter holes and plugging with cement mortar 1 :2 (1 cement
ii 2.35.3.1 Sq.Mt. 1069.78 227.05 242893.55
: 2 Coarse sand) to match the existing floor: With
Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Felling trees of the girth (measured at a height of 1 m above

ground level) including cutting of trunks and branches, removing
the roots and stacking of serviceable material and disposal of
unserviceable material. Wood material shall be the property of
14 2.33
the Owner and shall be disposed off as per the instructions of
DCF/Owner, all complete as per specification and direction of
Engineer-In-Charge

i 2.33.1 Beyond 30 cm girth upto and including 60 cm girth Each 1.00 380.60 380.60
ii 2.33.2 Beyond 60 cm girth upto and including 120 cm girth Each 2.00 1694.40 3388.80
iii 2.33.3 Beyond 120 cm girth upto and including 240 cm girth Each 2.00 7860.55 15721.10
iv 2.33.4 Above 240 cm girth Each 1.00 15749.95 15749.95
Transplantation of Trees including temporary supports before
excavation, excavation and pruning of roots in phased manner,
initiating fresh root growth, treatment of infections to tree (if
any), trimming of tree crown as per requirements, extracting
tree alongwith rootball, packing rootball with suitable material,
feeding the tree, safely loading, transportation (within site
premises/ at adjacent to the boundary as directed by Engineer in-
charge), unloading, digging of suitable size pit at transplantation
location, providing manure/fertilizer, pesticides and other
required treatments to soil, planting of tree, refilling soil,
providing & fixing temporary supports to prevent tree leaning,
15 NSI-1 watering, post transplantation treatment, all other measures to
ensure survival of tree and maintenance upto 1 year after
transplanting etc. all complete as per the scope of work,
specifications and directions of Engineer in Charge. Serviceable
material/ Forest produce arising out of pruning of tree shall be
property of contractor and it shall be disposed at nearest public
crematorium managed by MCD/NDMC/other statutory body
under proper receipt as per direction of Engineer-incharge.
(final measurement will be done for only survived trees)

i i Girth upto and including 60 cm girth each 5.00 54109.00 270545

ii ii Beyond 60 cm girth upto and including 90 cm each 4.00 64077.00 256308
iii iii Beyond 90 cm girth upto and including 120 cm girth each 2.00 78316.00 156632
iv iv Beyond 120 cm girth upto and including 150 cm girth each
v v Beyond 150 cm girth upto and including 180 cm girth each 3.00 92556.00 277668
vi vi Beyond 180 cm girth upto and including 240 cm girth each
vii vii Beyond 240 cm girth upto and including 300 cm girth each
viii viii Beyond 300 cm girth upto and including 400 cm girth each 1.00 135274.00 135274
Extra over above item for transplanting at location outside site
16 NSI-2 premises, instead of inside site premises (nos. of survived
transplanted trees shall be measured):
i i At location upto 10 KM from site premises Nos. 14.00 56957.00 797398

BOQ Civil Works Page 2 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

At location beyond 10 KM and upto 20 KM from site premises

ii ii Nos. 1.00 106795.00 106795

TOTAL (Carried Over to Summary of Civil Works) 7023838.07 2000620.00

B 4.0 CONCRETE WORKS

Providing and laying in position cement concrete of specified
1 4.1 grade excluding the cost of centering and shuttering - All work
up to plinth level :
1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural
i 4.1.4 sources : 4 graded stone aggregate 40mm nominal size derived Cu.Mt. 2.00 6680.20 13360.40
from natural sources).
1:3:6 (1 cement : 3 coarse sand (Zone-III) derived from natural
ii 4.1.5 sources : 6 graded stone aggregate 40mm nominal size derived Cu.Mt. 1.00 6259.10 6259.10
from natural sources).
1:4:8 (1 cement : 4 coarse sand (Zone-III) derived from natural
iii 4.1.8 sources : 8 graded stone aggregate 40mm nominal size derived Cu.Mt. 108.17 5789.60 626275.17
from natural sources).
Centering and shuttering including strutting, propping etc. and
2 4.3.1 removal of form work for : Foundations, footings, bases for Cu.Mt. 29.00 284.85 8260.65
columns.
Extra for providing and mixing water proofing material in cement
concrete work in doses by weight of cement as per Per 50 kg
3 4.12 384.99 56.55 21770.98
manufacturer's specification. cement

Extra for laying concrete in or under water and/or liquid mud Cum Per
4 4.15 including cum per cost of pumping or bailing out water and meter 8.30 794.65 6595.60
removing slush etc.complete. depth

TOTAL (Carried Over to Summary of Civil Works) 682521.89 0.00

C 5.0 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. and
1 5.9
removal of form for :
Foundations, footings, bases of columns, etc. for mass concrete.
i 5.9.1 Sq.Mt. 324.00 284.95 92323.80
Walls (any thickness) including attached pilasters,
ii 5.9.2 butteresses,plinth and string courses etc. Sq.Mt. 3502.78 609.30 2134244.71

Suspended floors, roofs, landings, balconies and access platform.

iii 5.9.3 Sq.Mt. 3944.42 693.05 2733683.18
iv 5.9.4 Shelves (Cast in situ) Sq.Mt. 37.37 693.05 25899.64
Lintels, beams, plinth beams, girders, bressumers and cantilevers
v 5.9.5 Sq.Mt. 3696.65 552.05 2040735.60

vi 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sq.Mt. 1215.54 733.70 891841.70
vii 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sq.Mt. 504.16 622.35 313763.98
Small lintels not exceeding 1.5m clear span, moulding as in
viii 5.9.15 cornices, window sills, string courses, bands, copings, bed plates, Sq.Mt. 26.73 284.85 7613.80
anchor blocks and the like.
ix 5.9.16 Edges of slabs and breaks in floors and walls
5.9.16.1 Under 20 cm wide Metre 975.00 173.25 168918.75
x 5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sq.Mt. 25.00 766.75 19168.75
Extra for additional height in centering, shuttering where ever
required with adequate bracing, propping etc., including cost of
de-shuttering and decentering at all levels, over a height of 3.5
2 5.11 m, for every additional height of 1 metre or part thereof (Plan
area to be measured).

Suspended floors, roofs, landing, beams and balconies

i 5.11.1 Sq.Mt. 550.02 287.50 158130.75
(Plan area to be measured)
Steel reinforcement for R.C.C. work including straightening,
3 5.22 cutting, bending, placing in position and binding all complete
upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
i 5.22.6 Kg 188662.45 83.50 15753314.58

Steel reinforcement for R.C.C. work including straightening,

4 5.22A cutting, bending, placing in position and binding all complete
above plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
i 5.22A.6 Kg 127105.00 83.50 10613267.50
Add for plaster drip course/ groove in plastered surface or
5 5.30 moulding to R.C.C. projections. Meter 975.00 58.90 57427.50

Extra for laying reinforced cement concrete in or under foul

6 5.32 positions. Cu.Mt. 1053.00 336.55 354387.15

BOQ Civil Works Page 3 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and laying in position machine batched and machine

mixed design mix M-25 grade cement concrete for reinforced
cement concrete work, using cement content as per approved
design mix, including pumping of concrete to site of laying but
excluding the cost of centering, shuttering, finishing and
7 5.33 reinforcement, including admixtures in recommended
proportions as per IS: 9103 to accelerate, retard setting of
concrete, improve workability without impairing strength and
durability as per direction of Engineer-in-charge.

(Note :- Cement content considered in this item is @ 330

kg/Cum. Excess/less cement used as per design mix is
payable/recoverable separately).
i 5.33.1 All works upto plinth level Cu.Mt. 5.00 7997.30 39986.50
ii 5.33.2 All works above plinth level upto floor V level. Cu.Mt. 5.00 9400.85 47004.25
Providing and laying in position ready mixed M-25 grade
concrete for reinforced cement concrete work, using cement
content as per approved design mix, manufactured in fully
automatic batching plant and transported to site of work in
transit mixer for all leads, having continuous agitated mixer,
manufactured as per mix design of specified grade for reinforced
cement concrete work, including pumping of R.M.C. from transit
mixer to site of laying , excluding the cost of centering,
shuttering finishing and reinforcement, including cost of
8 5.37 admixtures in recommended proportions as per IS : 9103 to
accelerate/ retard setting of concrete, improve workability
without impairing strength and durability as per direction of the
Engineer-in-charge. (Note :- Cement content considered in this
item is @ 330 kg/
cum.Excess/less cement used as per design mix is
payable/recoverable separately).

i 5.37.1 All works upto plinth level Cu.Mt. 1677.00 8398.65 14084536.05
ii 5.37.2 All works above plinth level upto floor V level Cu.Mt. 982.00 9802.20 9625760.40
Extra for providing richer mixes at all floor levels. Note:-
8 5.34 Excess/less cement over the specified cement content used is
payable /recoverable separately.
Providing M-30 grade concrete instead of M-25 grade BMC/
i 5.34.1 RMC. (Note:- Cement content considered in M-30 is @ 340 Cu.Mt. 1053.00 69.75 73446.75
kg/cum)
Providing M-35 grade concrete instead of M-25 grade
ii 5.34.2 BMC/RMC. (Note : Cement content considered in M-35 is @ 350 Cu.Mt. 518.82 139.45 72349.59
kg/ cum)
Add for using extra cement in the items of design mix over and
9 5.35 above the specified cement content therein. Quintal 2127.00 673.30 1432109.10

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each
10 5.38 four floors or part thereof. Cu.Mt. 241.36 280.95 67810.55

TOTAL (Carried Over to Summary of Civil Works) 60807724.58 0.00

D 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks
1 6.1 of class designation 7.5 in foundation and plinth in:
i 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 107.69 6376.25 686671.56
Half brick masonry with common burnt clay F.P.S. (non modular)
2 6.12 bricks of class designation 7.5 in foundations and plinth in :

i 6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 12.41 773.75 9604.17
Brick work with common burnt clay F.P.S. (non modular) bricks
3 6.4 of class designation 7.5 in superstructure above plinth level up to
floor V level in all shapes and sizes in :
i 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 621.05 7590.45 4714073.16
Extra for brick work / AAC block masonry / Tile brick masonry in
4 6.5 superstructure above floor V level, for each four floors or part Cum 154.52 236.65 36567.94
thereof by mechanical means.
Half brick masonry with F.P.S. bricks of class designation 75 in
5 6.13 superstructure above plinth level up to floor V level.

i 6.13.2 cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 670.11 932.10 624606.73

BOQ Civil Works Page 4 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Extra for half brick masonry in superstructure, above floor V

level for every four floors or part thereof by mechanical means.
6 6.14 Sqm 406.91 20.95 8524.85

Extra for providing and placing in position 2 Nos. 6mm dia. M.S.
7 6.15 bars at every third course of half brick masonry (with F.P.S. Sqm 670.11 80.10 53675.57
bricks).

TOTAL (Carried Over to Summary of Civil Works) 6133723.98 0.00

E 8.0 MARBLE & GRANITE WORK

Providing and fixing 18mm thick gang saw cut ( premoulded and
prepolished) machine cut for kitchen platforms, vanity counters,
window sills , facias and similar locations of required size of
approved shade, colour and texture laid over 20mm thick base
cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated
1 8.2 with white cement, mixed with matching pigment, epoxy touch
ups, including rubbing, curing, moulding and polishing to edge to
give high gloss finish etc. complete at all levels.

a) 8.2.2 Granite of any colour and shade

i 8.2.2.2 Area of slab over 0.50 sqm.( For Counter) Sqm. 36.31 4007.65 145511.85
Extra for fixing marble / granite stone over and above
corresponding basic item, in facia and drops of width upto
2 8.4 150mm with epoxy resin baesd adhesive including cleaning etc. metre 57.46 434.25 24951.57
complete.

Extra for providing opening of required size & shape for wash
basins/ kitchen sink in kitchen platform, vanity counters and
3 8.5 similar location in marble/Granite/Stone work including each 45.00 734.55 33054.75
necessary holes for pillar taps etc. including rubbing and
polishing of cut edge etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded
and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in
urinal partitions by cutting a chase of appropriate width with
chase cutter and embedding the stone in the chase with epoxy
4 8.10 grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 6 mm nominal size) as per direction of
Engineer-in-charge and finished smooth.

i 8.10.2 Granite Stone of approved shade Sqm 2.00 3216.90 6433.80

Providing and fixing machine cut, mirror/ eggshell polished ,
Marble stone work for wall lining (veneer work) including dado,
skirting, risers of steps etc., in required design and pattern
wherever required, stones of different finished surface texture,
on 12 mm (average) thick cement mortar 1:3 (1 cement : 3
coarse sand) laid and jointed with white cement slurry @ 3.3
5 8.11
kg/sqm including pointing with white cement slurry admixed
with pigment of matching shade, including rubbing, curing,
polishing etc. all complete as per Architectural drawings, and as
directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire

i 8.11.1 Sqm 122.56 8823.75 1081455.12
Red or Dark Emperadore etc.
Providing and Fixing stone work (machine cut edges) for wall
lining etc. (veneer work) upto 10 meter height, backing filled
with a grout of average 12 mm thick cement mortar 1:3 (1
cement : 3 coarse sand) including pointing in white cement
Derived
6 mortar 1:2 (1 white cement : 2 stone dust) with an admixture of
item (8.11)
pigment matching the stone shade : (To be secured to the
backing and the sides by means of cramps and pins which shall
be paid for separately)

18 mm thick mirror/ eggshell polished granite stone of approved

i a) Sqm 662.39 6561.55 4346314.62
shade.

BOQ Civil Works Page 5 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing dry cladding at all heights with 30 mm thick

granite stone of approved shade, fixed to structural steel frame
work and / or with the help of stainless steel cramps of required
shape and size, pins etc. and sealing the joints with approved
weather sealant including grouting the frame work/cramps/pins,
maintaining the grooves in stone slabs as per the drawing and
filling the same with non-staining, non-streaking silicon joint
sealants of approved make, including backer rod, drilling,
anchoring, grouting, scaffolding, edge polishing, chamfering to
Derived received tapered stone and providing and applying coating on
7
item (8.20) external surface of stone with solvent based silicone sealant of
approved make as per manufacturer's specifications etc., all
complete as per architectural drawings and direction of Engineer
in charge. (Only exposed surface will be measured for payment.
The steel frame work, stainless steel cramps and pins shall be
paid for separately).

Derived 30 mm thick mirror/ eggshell polished Granite Stone of

i item approved shade. Sqm 394.02 4149.40 1634955.09
(8.20.1)
Providing and fixing structural steel frame (for dry cladding with
30mm thick gang saw cut with machine cut edges sand stone) on
walls at all heights using M.S. square/ rectangular tube in the
required pattern as per architectural drawing, including cost of
cutting, bending, welding etc. The frame work shall be fixed to
the wall with the help of M.S. brackets/ lugs of angle iron/ flats
etc. which shall be welded to the frame and embedded in brick
wall with cement concrete block 1:2:4 (1 cement :2 coarse sand
:4 graded stone aggregate 20 mm nominal size) of size
300x230x300 mm, including cost of necessary centring and
shuttering and with approved expansion hold fasteners on
CC/RCC surface, including drilling necessary holes. Approved
8 8.21 kg 985.06 202.40 199375.16
cramps/ pins etc. shall be welded to the frame work to support
stone cladding, the steel work will be given a priming coat of Zinc
primer as approved by Engineerin-charge and painted with two
or more coats of epoxy paint (Shop drawings shall be submitted
by the contractor to the Engineer-in-charge for approval before
execution). The frame work shall be fixed in true horizontal &
vertical lines/planes. (Only structural steel frame work shall be
measured for the purpose of payment, stainless steel cramps
shall be paid for separately and nothing extra shall be paid).

Providing and fixing adjustable stainless steel cramps of

approved quality, required shape and size, adjustable with
stainless steel nuts, bolts and washer (total weight not less than
260 gms), for dry stone cladding fixed on frame work at suitable
9 8.22 location, including making necessary recesses in stone slab, Each 788.00 327.00 257676.00
drilling required holes etc complete as per drawings,
specification and direction of the Engineer-in-charge.

Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by
Engineer-in-Charge, in skirting, risers of steps and dados, over 12
10 8.31 Sqm 931.32 1030.30 959534.36
mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)
and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade
complete.

BOQ Civil Works Page 6 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Cost of ACP Panel Cladding includes cost of Aluminum frame as

desired behind ACP Panel, Weather Sealant, Foam/ Backer Rod,
screws, cleats all required machineries for fixing. Including the
labor element for cutting and fabrication of ACP panel along with
aluminum angle stiffener as desired at back for stability,
11 NSI-3 stacking, carrying to heights and fixing in
appropriate locations shall be included in the rates. Only visible
surface area of aluminum composite panel along with its groove
shall be measured for payment.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with

Hot Dip Galvanised with serrations and serrated washers to
arrest the wind load movement, fasteners, SS 316 Pins and
anchor bolts of approved make in SS 316, Nylon separators to
prevent bi-metallic contacts all complete required to perform as
per specification and drawing The item includes cost of all
material & labour component, the cost of all mock ups at site,
cost of all samples of the individual components for testing in an
approved laboratory, field tests on the assembled working
curtain wall with aluminium composite panel cladding, cleaning
and protection of the curtain wall with aluminium composite
panel cladding till the handing over of the building for
occupation. The Contractor shall provide curtain wall with
a) aluminium composite panel cladding,and including base frame Sqm 1138.16 4894.00 5570177.21
work for ACP having all the performance characteristics all
complete , as per the Architectural drawings, as per item
description, as specified, as per the approved shop actor and it
shall be disposed at nearest public crematorium managed by
MCD/NDMC/other statutory body under proper receipt as per
direction of Engineer-incharge.
(final measurement will be done for only survived trees), parlite,
vermilite & good earth, suitable for pla

TOTAL (Carried Over to Summary of Civil Works) 8689262.32 5570177.21

F 9.0 WOOD & PVC WORK

Providing & fixing Factory made single extruded WPC (Wood
Polymer Composite) solid door/window/Ceosetory windows &
other frame/ Chowkhat comprising of virgin PVC Polymer of K
value 58-60 (Suspension Grade), calcium corbonate and natural
fibers (wood powder/rice husk/wheat husk) and non toxic
additives (maximum toxicity index of 12 for 100gms) fabricated
with milter joints after applying PVC solvent cement and
screwed with full body threaded star headed SS Screws having
minimum frame density of 750kg/cum, screws withdrawal
strength of 2200 N (Face) & 1100 N (Edge), minimum
1 26.86.6 metre 491.00 1301.65 639110.15
compressive strength of 58 N/mm2, modulus of elasticity 900
N/mm2 and resistance to spread of frame of class A category
with property of being termite/ borer proof, water/ moisture
proff and fire retardant and fixed in position with M.S hold
fast/lugs/SS dash fastners of required dia and length complete as
per direction of Engineer-in-charge. (M.S hold fast/lugs or SS
dash fastners shall be paid for separately). Frame Size
65x125mm.

Providing and fixing ISI marked flush door shutters conforming to

IS : 2202 (Part I) non-decorative type, core of block board
construction with frame of 1st class hard wood and well
2 9.21 matched commercial 3 ply veneering with vertical grains or cross
bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

i 9.21.1 sqm 221.00 1886.70 416960.70
necessary screws
Extra for providing lipping with 2nd class teak wood battens 25
mm minimum depth on all edges of flush door shutters (over all
3 9.23 Sqm 221.00 401.40 88709.40
area of door shutter to be measured).

BOQ Civil Works Page 7 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing wooden moulded beading to door and

4 9.40 window frames with iron screws, plugs and priming coat on
unexposed surface etc. complete :
a 9.40.1 2nd class teak wood
i 9.40.1.1 50x12 mm Rmt 245.50 184.60 45319.30
Providing 40x5 mm flat iron hold fast 40 cm long including fixing
to frame with 10 mm diameter bolts, nuts and wooden plugs and
embedding in cement concrete block 30x10x15cm 1:3:6 mix (1
5 9.53 Each 364.00 179.20 65228.80
cement : 3 coarse sand : 6 graded stone aggregate 20mm
nominal size).

Providing and fixing 2nd class teak wood corner beading of

triangular shape and size 50x50 mm (base and height) moulded
to the junction of paneling, edgings, margins etc. fixed in position
6 9.111 with rawl plugs, nails etc. as required and priming coat on Meter 491.00 300.60 147594.60
unexposed surface complete with rubbing, polishing etc. as per
the direction of Engineer in Charge.

Provrd ng and applying / spraying melamlne and requied shade

two or more coats on new wood works including a coat of wood
7 NSI-4 filler/ sealer, surface preparation by sanding etc. complete as Sqm 394.75 1143.60 451436.10
per Engineer-in-charae.

Providing & Fixing 1 mm thick decorative high pressure

laminated sheet of plain / wood grain in gloss / matt / suede
finish of approved make with high density protective surface
layer and reverse side of adhesive bonding quality conforming to
8 9.127.2 Sqm 170.00 717.65 122000.50
IS : 2046 Type S, including cost of adhesive of approved quality,
all complete as per directions of Engineer in Charge.

Hardware
Providing and Fixing approved brand and manufacture of
Stainless Steel 2 Ball Bearing Hinge 102x76x3mm along with
necessary accessories and screws etc. complete in all respects as
9 NSI-5 per manufacture ofrs' specificatios & as directed by Engineer-in- Each 440 355.10 1,56,244.00
charge.

Providing and fixing approved brand and manufacture of Brass

Towerbolt 300 mm long with 10 mm dia along with necessary
10 NSI-6 accessories and screws etc. complete in all respects as per Each 220 1,208.80 2,65,936.00
manufacture ofrs' specificatios & as directed by Engineer-in-
charge.
Providing and fixing approved brand and manufacture of
Stainless Steel Towerbolt 150 mm long with 10 mm dia along
11 NSI-7 with necessary accessories and screws etc. complete in all Each 10 248.65 2,486.50
respects as per manufacture ofrs' specificatios & as directed by
Engineer-in-charge.

Providing and fixing approved brand and manufacture of Stain

less Steel Floor stoper floor mounted half round with 45mm dia
along with necessary accessories and screws etc. complete in all
12 NSI-8 respects as per manufacture ofrs' specificatios & as directed by Each 110 354.25 38,967.50
Engineer-in-charge.

Providing and fixing approved brand and manufacture of Brass

Door Guard Buckle Type (DGBT) along with necessary
13 NSI-9 accessories and screws etc. complete in all respects as per Each 11 853.10 9,384.10
manufacture ofrs' specificatios & as directed by Engineer-in-
charge.
Providing and fixing approved brand and manufacture of
Stainless Steel Door Buffer wall mounted 22 mm dia,75 mm long
along with necessary accessories and screws etc. complete in all
14 NSI-10 Each 110 244.80 26,928.00
respects as per manufacture ofrs' specificatios & as directed by
Engineer-in-charge.

Providing and approved brand and manufacture of Brass Door

stopper - Door Mounted Hanging Type (DSHT) along with
15 NSI-11 necessary accessories and screws etc. complete in all respects as Each 110 385.85 42,443.50
per manufacture ofrs' specificatios & as directed by Engineer-in-
charge.

BOQ Civil Works Page 8 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing approved brand and manufacture of Door

Safety Chain along with necessary accessories and screws etc.
16 NSI-12 complete in all respects as per manufacture ofrs' specificatios & Each 11 524.00 5,764.00
as directed by Engineer-in-charge.

Providing and fixing Sliding bolt (baby latch) with SS lock strip 5''
along with necessary accessories and screws etc. complete in all
17 NSI-13 respects as per manufacture ofrs' specificatios & as directed by Each 42 391.15 16,428.30
Engineer-in-charge.

Providing and fixing approved brand and manufacture of

Indicator Bolt along with necessary accessories and screws etc.
18 NSI-14 complete in all respects as per manufacture ofrs' specificatios & Each 21 680.60 14,292.60
as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture of

aluminium extruded section tubular type universal hydraulic
door closer with Palmet Arm having brand logo , embossed on
the body, door weight upto 80 kg , 5 lacs Cycles Tested), with
19 NSI-15 speed adjustment along with necessary accessories and screws Each 75.00 4,657.45 3,49,308.75
etc. complete in all respects as per manufacture ofrs'
specificatios & as directed by Engineer-in-charge.

Door Handles and Locks

Providing and fixing approved brand and manufacture of Floor
spring ( for the weight carring capacity of 65 to 100 Kg. without
BP/TP along with necessary accessories and screws etc.
20 NSI-16 complete in all respects as per manufacture ofrs' specificatios & Each 21 6,882.95 1,44,541.95
as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture of Floor

spring ( for the weight carring capacity of 120 Kg. without BP/TP
along with necessary accessories and screws etc. complete in all
21 NSI-17 respects as per manufacture ofrs' specificatios & as directed by Each 21 5,753.40 1,20,821.40
Engineer-in-charge.

Providing and fixing approved brand and manufacture of

Madona Design Mortice Lever handle On Rose along with
22 NSI-18 necessary accessories and screws etc. complete in all respects as Each 0 4,901.20 0.00
per manufacture ofrs' specificatios & as directed by Engineer-in-
charge.
Providing and fixing approved brand and manufacture of Terza
Design Mortice Lever handle On Plate along with necessary
23 NSI-19 accessories and screws etc. complete in all respects as per Each 110 4,030.50 4,43,355.00
manufacture ofrs' specificatios & as directed by Engineer-in-
charge.
Providing and fixing approved brand and manufacture of Mortice
Sash lock with 85 mm CD & 50 mm Backset along with key
cylinder fixing Option along with necessary accessories and
24 NSI-20 Each 110 1,418.40 1,56,024.00
screws etc. complete in all respects as per manufacture ofrs'
specificatios & as directed by Engineer-incharge.

Providing and fixing approved brand and manufacture of Mortice

Latch For Steel Door Backset along with necessary accessories
and screws etc. complete in all respects as per manufacture ofrs'
25 NSI-21 specificatios & as directed by Engineer-in-charge. Each 11 1,065.40 11,719.40

Providing and fixing approved brand and manufacture of Euro

Profile Cylinder one side key & other side knob 60 mm along
26 NSI-22 with necessary accessories and screws etc. complete in all Each 110 1,300.70 1,43,077.00
respects as per manufacture ofrs' specificatios & as directed by
Engineer-in-charge.
Providing and fixing approved brand and manufacture of Tri Lock
Inside Key & outside Key Opening (PHA 300 NS) with High
Security locking pins along with necessary accessories and
27 NSI-23 Each 11.00 4,089.35 44,982.85
screws etc. complete in all respects as per manufacture ofrs'
specificatios & as directed by Engineer-in-charge.

BOQ Civil Works Page 9 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing factory made uPVC white colour

casement/casement cum fixed glazed windows comprising of
uPVC multi-chambered frame, sash and mullion (where ever
required) extruded profiles duly reinforced with 1.60 ± 0.2 mm
thick galvanized mild steel section made from roll forming
process of required length (shape & size according to uPVC
profile), uPVC extruded glazing beads of appropriate dimension,
EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc
alloy (white powder coated) casement handles, G.I fasteners 100
x 8 mm size for fixing frame to finished wall, plastic packers,
plastic caps and necessary stainless steel screws etc. Profile of
frame & sash shall be mitred cut and fusion welded at all
corners, mullion (if required) shall be also fusion welded
28 9.147A including drilling of holes for fixing hardware's and drainage of
water etc. After fixing frame the gap between frame and
adjacent finished wall shall be filled with weather proof silicon
sealant over backer rod of required size and of approved quality,
all complete as per approved drawing & direction of Engineer-in-
Charge. (Single / double glass panes and silicon sealant shall be
paid separately).
Note: For uPVC frame, sash and mullion extruded profiles minus
5% tolerancein dimension i.e. in depth & width of profile shall be
acceptable. Variation in profile dimension in higher side shall be
accepted but no extra payment on this account shall be made.

Casement window single panel with S.S. friction hinges (300 x 19

x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x
i 9.147A.1 68 mm both having wall thickness of 1.9 ± 0.2 mm and single Sqm 13.00 9483.50 123285.50
glass pane glazing bead of appropriate dimension. (Area of
window upto 0.75 sqm.)

Casement window double panels with top fixed with S.S. friction
hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50
mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall
ii 9.147A.3 thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate Sqm 1.80 6982.00 12567.60
dimension. ( Area of window upto 2.50 sqm).

Providing and fixing factory made uPVC white colour fixed glazed
windows/ ventilators comprising of uPVC multi-chambered
frame and mullion (where ever required) extruded profiles duly
reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section
made from roll forming process of required length (shape & size
according to uPVC profile), , uPVC extruded glazing beads of
appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm
size for fixing frame to finished wall, plastic packers, plastic caps
and necessary stainless steel screws etc. Profile of frame shall be
mitred cut and fusion welded at all corners, mullion (if required)
shall be also fusion welded including drilling of holes for fixing
hardware's and drainage of water etc. After fixing frame the gap
29 9.147B between frame and adjacent finished wall shall be filled with
weather proof silicon sealant over backer rod of required size
and of approved quality, all complete as per approved drawing &
direction of Engineer-in-Charge. (Single / double glass panes and
silicon sealant shall be paid separately).
Note: For uPVC frame, sash and mullion extruded profiles minus
5% tolerance in dimension i.e. in depth & width of profile shall
be acceptable. Variation in profile dimension in higher side shall
be accepted but no extra payment on this account shall be
made.

Fixed window / ventilator made of (small series) frame 47 x 50

mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2
i 9.147B.1 Sqm 3.65 6478.75 23647.44
mm and single glazing bead of appropriate dimension. (Area
upto 0.75 sqm.)

BOQ Civil Works Page 10 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing factory made uPVC white colour casement/

Casement cum fixed glazed door comprising of uPVC multi-
chambered frame, sash and mullion (where ever required)
extruded profiles duly reinforced with 1.60 ± 0.2 mm thick
galvanized mild steel section made from roll forming process of
required length (shape & size according to uPVC profile), uPVC
extruded glazing beads of appropriate dimension, EPDM gasket,
zinc alloy (white powder coated) 3D hinges and one handle on
each side of panels along with zinc plated mild steel multi point
locking having transmission gear, cylinder with keeps and one
side key, G.I fasteners 100 x 8 mm size for fixing frame to
finished wall and necessary stainless steel screws, etc. Profile of
30 9.147.C frame & sash shall be mitred cut and fusion welded at all
corners, mullion (if required) shall be also fusion welded
including drilling of holes for fixing hardware's and drainage of
water etc. After fixing frame the gap between frame and
adjacent finished wall shall be filled with weather proof silicon
sealent over backer rod of required size and of approved quality,
all complete as per approved drawing & direction of Engineer-in-
Charge. (Single / double glass panes and silicon sealent shall be
paid separately).
Note: For uPVC frame, sash and mullion extruded profiles minus
5% tolerance in dimension i.e. in depth & width of profile shall
be acceptable. Variation in profile dimension in higher side shall
be accepted but no extra payment on this account shall be
Casement door with 3D hinges made of (big series) frame 67 x 64
mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2
i 9.147C.1 mm and single glazing bead / double glazing bead of appropriate Sqm 3.10 9131.45 28307.50
dimension. (Area of door upto 2.00 sqm).

Casement door with top hung ventilator with 3D and S.S. friction
hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64
mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall
ii 9.147C.2 thickness of 2.3 ±. 0.2 mm and single glazing bead / double Sqm 4.00 9328.30 37313.20
glazing bead of appropriate dimension.(Area of door upto 2.50
sqm)

Providing and fixing factory made uPVC white colour sliding

glazed window upto 1.50 m in height dimension comprising of
uPVC multi-chambered frame with in-built roller track and sash
extruded profiles duly reinforced with 1.60 ± 0.2 mm thick
galvanized mild steel section made from roll forming process of
required length (shape & size according to uPVC profile),
appropriate dimension of uPVC extruded glazing beads and uPVC
extruded interlocks, EPDM gasket, wool pile, zinc alloy (white
powder coated) touch locks with hook, zinc alloy body with
single nylon rollers (weight bearing capacity to be 40 kg), G.I
fasteners 100 x 8 mm size for fixing frame to finished wall and
31 9.147D necessary stainless steel screws etc. Profile of frame & sash shall
be mitred cut and fusion welded at all corners, including drilling
of holes for fixing hardware's and drainage of water etc. After
fixing frame the gap between frame and adjacent finished wall
shall be filled with weather proof silicon sealent over backer rod
of required size and of approved quality, all complete as per
approved drawing & direction of Engineer-in-Charge. (Single /
double glass panes, wire mesh and silicon sealent shall be paid
separately).
Note: For uPVC frame and sash extruded profiles minus 5%
tolerance in dimension i.e. in depth & width of profile shall be
acceptable.
Variation
Three trackin profile dimension
three panels in higher
sliding windowside shallflybeproof
with accepted
S.S wire
mesh (Two nos. glazed & one no. wire mesh panels) made of (big
series) frame 116 x 45 mm & sash 46 x 62 mm both having wall
i 9.147D.4 thickness of 2.3 ± 0.2 mm and single glazing bead / double Sqm 73.00 8616.00 628968.00
glazing bead of appropriate dimension. (Area of window above
1.75 sqm).

Providing and fixing fly proof stainless steel grade 304 wire
Derived gauge, to windows, Doors and clerestory windows using wire
32 Item gauge with average width of aperture 1.4 mm in both directions Sqm 24.33 1841.45 44808.62
(9.135.2) with wire of dia. 0.50 mm all complete. With Upvc Snap beading.

Fire rated steel door

BOQ Civil Works Page 11 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing at all levels & locations, 120 minutes fire
rated steel Fire door and frame of Galvanized steel conforming
to IS:277 of approved make, overall door assembly conforming
33 NSI-24 Sqm 23.00 8064.0 185472.0
to IS 3614 Part-1 & Part-2 & BS 476 Part 22 or EN 1634 as
required . Fire doors should be tested at CBRI or ARAI for rating
of 120 minutes.
Door frame shall be double rebate profile of size 143 x 57 mm
made with minimum 1.6mm thick galvanized steel sheet. Frames
shall be mitered and field assembled with self tabs. All provisions
should be mortised, drilled and tapped for receiving suitable fire
rated hardware. Suitable Rubber door silencers should be
provided on the striking jamb. Frames should be provided with
back plate bracket and anchor fasteners for installation on a
finished plastered masonry wall opening. Frame should be
grouted with cement & sand slurry necessary for fire doors on
the clear masonry opening.

Door shutter shall be made with minimum 1.2 mm thick steel

pressed formed to provide a 46mm thick fully flush double skin
door shell with lock seam joints at stiled edges. The internal
construction or in fill material of the door to meet desired fire
rating with reinforcement/rails at top, bottom, middle and
vertical stile. The infill material shall be resin bonded honeycomb
core or approved equivalent. The door shall be factory prepared
for receiving appropriate hardware and provided with necessary
reinforcement for hinges, locks, and door closers etc complete.
The edges should be interlocked with a bending radius of
1.4mm. and shall have door astragals of required profile and size
provided on the meeting stile for both active and inactive leaf.
The shutter is to be fixed with frame with SS ball bearing butt
hinges 3mm thick. Frame shall be fixed with approved dash
fasteners and concrete should be poured in hollow frame
section etc. Vision panel wherever applicable should be of size at
least 300 x 300mm pather proof silicon sealent over backer rod
of required size and of approved quality, all complete as per
approved drawing & direction of Engineer-in-Charge. (Single /
double glass panes and silicon sealent shall be paid separately).
Note: For uPVC frame, sash and mullion extruded profiles minus
5% tolerance in dimension i.e. in depth & width of profile shall
be acceptable. Variation in profile dimension in higher side shall
be accepted but no extra payment on this account shall be
made.r direction of Engineer-In-Charge.of 37mm inside diameter
and outside diameter 40.2mm extruded tube to have a 1.6mm
wall thickness with
Providing & fixing Fire rated door Closer of approved make
34 NSI-25 certified for 2Hrs fire rating, all complete as per direction of Each 8.00 2994.0 23952.0
Engineer in Charge.
Providing & fixing Fire rated Panic Exit Device (Panic Bar) of
approved make certified for 2Hrs fire rating for single leaf door,
35 NSI-26 Each 8.00 7149.0 57192.0
all complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Panic Exit Device (Panic Bar) of
approved make certified for 2Hrs fire rating for double leaf door,
36 NSI-27 Each 4.00 14297.0 57188.0
all complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Lock with external leaver

handle/panic trim for Operation From The Other Side Of The
37 NSI-28 Panic Bar of approved make certified for 2Hrs fire rating, all Each 8.00 5856.0 46848.0
complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Lock of approved make certified for
38 NSI-29 2Hrs fire rating, all complete as per direction of Engineer in Each 8.00 5570.0 44560.0
Charge.
Providing & fixing Stainless Steel 304 grade 300mm Long Flush
Bolt with necessary screws as required in Double Leaf Doors all
39 NSI-30 Each 16.00 1269.0 20304.0
complete as per direction of Engineer in Charge.

Supply of SS Ball Bearing Hinges of size 100 x 75 x 3mm complet

with SS Screws of 3S2BB403030-MS Assa Abloy(Yale) Make ( 4
40 NSI-31 Each 32.00 299.0 9568.0
Nos per panel ) (Required For All Doors) as per the directions of
Engineer-in-charge

TOTAL (Carried Over to Summary of Civil Works) 2423821.30 2889224.95

G 10.0 STEEL WORK

BOQ Civil Works Page 12 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Steel work welded in built up sections/ framed work including

cutting, hoisting, fixing in position and applying a priming coat of
1 10.25
approved steel primer using structural steel etc. as required

In stringers, treads, landings etc. of stair cases including use of

i 10.25.1 Kg 150.00 93.65 14047.50
chequered plate wherever required, all complete.
In gratings, frames, guard bar, ladder, railings, brackets, gates
ii 10.25.2 Kg 175.00 131.00 22925.00
and similar works.

Providing and fixing 1mm thick M.S. sheet door with frame of
40x40x6 mm angle iron and 3 mm M.S. gusset plates at the
2 10.5
junctions and corners, all necessary fittings complete, including
applying a priming coat of approved steel primer.
i 10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces sqm 5.04 4428.15 22317.88
Supplying and fixing-rolling shuters of approved make.made of
required size of M.S.Iaths inter locked together through their
intire length and jointed together at the end by end locks
mounted on specially designed pipe shaft with brackets, side
3 10.6 guides and arragements for inside and outside locking with push
and pull operation complete including the cost of prioviding and
fixing necessary 27.5 cm long wire springs grade no. 2 and M.S.
top cover of required thickness for rolling shutters.

i 10.6.1 80 x 1.25 MS laths with 1.25mm thick top cover Sqm 29.43 2944.10 86636.03
ii 10.7 Providing and fixing ball bearing for rolling shutters. each 4.00 419.85 1679.40
Extra for providing mechanical device chain and crank operation
iii 10.8
for operating rolling shutter.
iv 10.8.1 Exceeding 10.00 Sqm and upto 16.8 Sqm in the area. Sqm 29.43 1106.55 32562.45
Extra for providing grilled rolling shutters manufactured out of
8mm dia M.S. Bar instead of laths as per design approved by
v 10.9 Sqm 3.46 668.95 2315.90
Engineer-in-Charge (Area of grill to be measured).

Steel work in built up tubular ( round, square or rectangular

hollow tubes etc.) trusses etc., including cutting, hoisting, fixing
4 10.16 in position and applying a priming coat of approved steel primer,
including welding and bolted with special shaped washers etc.
complete.
i 10.16.1 Hot finished welded type tubes Kg 2023.35 143.45 290249.56
Providing and fixing circular/ Hexagonal cast iron or M.S. sheet
box for ceiling fan clamp, of internal dia 140 mm, 73 mm height,
top lid of 1.5 mm thick M.S. sheet with its top surface hacked for
proper bonding, top lid shall be screwed into the cast iron/ M.S.
5 10.18 sheet box by means of 3.3 mm dia round headed screws, one Each 75.00 172.25 12918.75
lock at the corners. Clamp shall be made of 12 mm dia M.S. bar
bent to shape as per standard drawing.

Providing and fixing carbon steel galvanised ( minimum coating 5

micron) dash fastener of 10 mm dia double threaded 6.8 grade
(yield strength 480 N/mm2), counter sunk head, comprising of
6 10.27
10 m dia polyamide PA 6 grade sleeve, including drilling of hole
in frame , concrete/ masonry, etc. as per direction of Engineer-in-
charge.
i 10.27.2 10 x 80 mm each 221.00 109.00 24089.00
Providing and fixing stainless steel ( Grade 304) railing made of
Hollow tubes, channels, plates etc., including welding, grinding,
buffing, polishing and making curvature (wherever required) and
fitting the same with necessary stainless steel nuts and bolts
complete, i/c fixing the railing with necessary accessories &
stainless steel dash fasteners , stainless steel bolts etc., of
7 10.28 KG 1327.33 575.45 763812.05
required size, on the top of the floor or the side of waist slab
with suitable arrangement as per approval of Engineer-in-
charge, (for payment purpose only weight of stainless steel
members shall be considered excluding fixing accessories such as
nuts, bolts, fasteners etc.).

Providing Toughened glass 12 mm thickness fixed to stainless

item No. steel ( Grade 304) railing made of Hollow tubes and fixing
8 accessories such as nuts, bolts, fasteners etc.(excluding Stainless Sqm 132.73 2717.05 360642.20
(8778)
steel railing )

TOTAL (Carried Over to Summary of Civil Works) 1634195.71 0.00

H 11.0 FLOORING WORK

BOQ Civil Works Page 13 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate) finished with a floating coat of neat
1 11.3 cement, including cement slurry, but excluding the cost of nosing
of steps etc. complete.
i 11.3.1 40 mm thick with 20 mm nominal size stone aggregate Sqm 1133.92 498.35 565090.48
Cement plaster skirting up to 30 cm height, with cement mortar
2 11.6 1:3 (1 cement : 3 coarse sand), finished with a floating coat of
neat cement.
i 11.6.1 18 mm thick Sqm 10.00 521.15 5211.50
Chequerred precast cement concrete tiles 22 mm thick in
footpath & courtyard, jointed with neat cement slurry mixed
with pigment to match the shade of tiles,including rubbing and
3 11.20.1 cleaning etc. complete, on 20 mm thick bed of cement mortar Sqm 568.07 1221.65 693984.61
1:4 (1 cement: 4 coarse sand). Light shade pigment using white
cement.
Marble stone flooring with 18 mm thick marble stone, as per
sample of marble approved by Engineer-in-charge, over 20 mm
(average) thick base of cement mortar 1:4 (1 cement : 4 coarse
4 11.23
sand) laid and jointed with grey cement slurry, including rubbing
and polishing complete with :

i 11.23.1 Makrana white second quality Sqm 17.05 3237.80 55198.01

Extra for pre finished nosing to treads of steps of marble /
5 11.24 Rmt 679.00 530.25 360039.75
granite stone.
Extra for marble / granite stone flooring in treads of steps and
6 11.25 Sqm 318.00 622.75 198034.50
risers using single length up to 2.00 metre.
Kota stone slab flooring over 20 mm (average) thick base laid
over and jointed with grey cement slurry mixed with pigment to
7 11.26 match the shade of the slab including rubbing and polishing
complete with base of cement mortar 1 : 4 (1 cement : 4 coarse
sand) :
i 11.26.1 25 mm thick. Sqm 263.46 1531.85 403574.16
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and
pillars laid on 12 mm (average) thick cement mortar 1:3 (1
8 11.27 cement 3 coarse sand) and jointed with grey cement slurry Sqm 29.96 1810.05 54229.01
mixed with pigment to match the shade of the slabs, including
rubbing and polishing complete.

Providing & Laying vitrified floor tiles in different sizes ( thickness

to be specified by the manufacturer) with water absorption's
less than 0.08% and confirming to IS : 15622 of approved make
9 11.41 in all colours and shades, laid on 20mm thick cement mortar 1:4
(1 cement : 4 coarse sand) including grouting the joints with
white cement and matching pigments etc, complete.

i 11.41.2 Size of Tile 600x600 mm Sqm 230.73 1500.55 346214.44

Supplying and laying true to line and level Primium Quality
Double Charged Vitrified Tiles of approved brand conforming to
IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006
(relevant parts) [Non-modular sizes for tiles with Water
Absorption (av.) ≤ 0.08 %] in floor, skirting etc. set in 20 mm
thick sand cement mortar (1:4) bed prepared after application of
slurry using 1.75Kg of cement per Sqm over the base and 2mm
thick cement slurry using cement @2.91Kg./sqm at the back side
Derived of the tiles and laid over the mortar bed using 0.2 kg/sqm of
10 item White cement used for joint filling with approved pigment as
(11.41.2) directed and removal of wax coating of top surface of tiles with
warm water and polishing the tiles using soft and dry cloth upto
mirror finish complete including the cost of materials,Iabour and
all other incidental charges complete true to the manufacturer's
specification and direction of Engineer-in-Charge. (Note: This
work should not be executed without specific permission of
Superintending Engineer)

Size of Tile 600x600 mm (Minimum basic rate of Tiles Rs. 70/-

i i Sqm 31.85 1694.75 53970.14
per Sqft)
Providing and laying Vitrified tiles in different sizes (thickness to
be specified by manufacturer), with water absorption less than
0.08 % and conforming to I.S. 15622, of approved make, in all
colours & shade, in skirting / dado, riser of steps, over 12 mm
11 11.46 thick bed of cement mortar 1:3 (1 cement: 3 coarse sand),
jointing with grey cement slurry @ 3.3 kg/ sqm including
grouting the joint with white cement & matching pigments etc.
complete.

BOQ Civil Works Page 14 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

i 11.46.2 Size of Tile 600x600 mm Sqm 5.05 1545.85 7798.97

Providing and laying machine cut, mirror polished, Italian Marble
stone flooring laid in required pattern in linear portion of the
building all complete as per architectural drawings, with 18 mm
thick stone slab laid over 20mm (average) thick base of cement
mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white
12 11.51 cement slurry @ 4.4 kg/sqm including pointing with white
cement slurry admixed with pigment to match the marble shade
including rubbing, curing and polishing etc. all complete as
specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona,

i 11.51.1 Sqm 976.81 5988.40 5849557.69
Fire Red or Dark Emperadore etc.
Providing and laying Polished Granite stone flooring in required
design and patterns, in linear as well as curvilinear portions of
the building all complete as per the architectural drawings with
18 mm thick stone slab over 20 mm (average) thick base of
cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed
13 11.56 with cement slurry and pointing with white cement slurry
admixed with pigment of matching shade including rubbing ,
curing and polishing etc. all complete as specified and as
directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown,
i 11.56.1 Sqm 833.06 3526.60 2937855.71
Cat Eye or equivalent.
Providing and Laying 8mm thick VIBRANCE Laminate Floors
confirming to EN 13329 standards. Class of Use 23/32, Grade
14 NSI-32 AC4 with all certifications. The cost includes fixing of flooring and Sqm 583.71 3573.30 2085769.19
accessories such skirting, door trims, etc

Providing and laying readymade MDF Skirting 12mm x 100 mm

i NSI-33 Meter 210.91 932.60 196694.67
of matching colour.
Providing and laying modular carpet of approved make and
shade and made with 100% nylon 6/6.6 tufted textured tip
sheared/ cut & loop piles, tiles of minimum 500mm x 500mm in
size, stain resistant, anti microbial, and having colour fastness to
water, fastness to light, rubbing fastness and castor chair
suitability as per relevant standard for heavy commercial usage,
with PVC free backing, nominal total thickness of minimum 6.50
15 NSI-34 mm, pile height minimum 3.4 mm, minimum Total Pile weight – Sqm 550.21 2383.80 1311598.68
800g/sqm). Material shall be CRI GREEN LABEL PLUS certified,
and shall have recycled content complying to GRIHA
requirement, including fixing with GRIHA compliant adhesive of
approved make, all complete as per drawings, manufacturer's
specifications and direction of Engineer in Charge.

Trimix Flooring
Providing and laying reinforced cement concrete
flooring/pavement of M25 (Minimum cement content to be
used is 330 Kg/Cum) Grade at any level with ready mixed
concrete including necessary centering & side shuttering with
MS channels, vibrating, curing, cutting of VDF floor with
Diamond Saw system for a groove of 8mm wide & 20mm deep in
flooring surface and filling with bitumen or silicon as instructed
Derived by the engineer in charge, including vacuum dewatering the
16 Sqm 1345.89 904.85 1217828.57
item (16.43) concrete floors and finishing the top surface to required
level/slope and grade with rough/polish finish using power
trowels (both fan & disc ) including curing etc. complete as per
specification, with nominal reinforcement as per drawing but
the cost of reinforcement shall be paid in the respective item of
reinforcement. (Thickness of RCC flooring shall be 50 to 150mm
for slope)

BOQ Civil Works Page 15 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Supply and Installation of FunderMax 6mm thick Exterior grade F-

Quality panels of standard size with both side décor .FunderMax
Exterior panels are Duromer high-pressure laminates (HPL) as
per EN 438-6 type EDF manufactured with norm conformity of
EN 438-7 using patented NT Technology (NT is Non fading high
performance acrylic polyurethane surface Technology). Panels
will be double hardened including acrylic polyurethane resin and
thermally cured under high pressure. These Panels will have CE-
Mark necessary for their use in building applications. Installation
of FunderMax panels will be done by MBE Rivets (with Fixed and
Sliding Points) with recommended Aluminum T section of
17 NSI-35 75x37x2.8 mm thick and L section 38x38x2.8mm thick held by Sqm 964.46 6023.45 5809371.77
Aluminum Wall Bracket with Wind load and Dead load slot as
designed and provided by Fundermax India pvt. ltd., anchored by
standard anchor fasteners along with Thermal Separator.
Installation of FunderMax Panels will be done using Rear
Ventilated Principles only, which is ensured of approved quality,
all complete as per approved drawing & direction of Engineer-in-
Charge. (Single / double glass panes, wire mesh and silicon
sealent shall be p

Supplying & laying of approved brand of EPDM Membrane

Flooring conforming to IS:3461, fixing with synthetic acrylic
adhesive after preparing the floor, levelling & smothaning when
18 NSI-36 Sqm 21.35 4591.80 98032.63
necessary with suitable putty, as per the design & instruction of
the Engineer-in-charge.

TOTAL (Carried Over to Summary of Civil Works) 12694617.39 9555437.08

I 12.0 ROOFING
Providing and laying gola 75x75mm in cement concrete M15
grade including finishing with cement mortar 1:3 (1 cement : 3
1 12.21 Rmt 173.00 237.25 41044.25
fine sand) as per standard design in 75x75 mm deep chase.

Making khurras 45x45 cm with average minimum thickness of 5

cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1
2 12.22 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 Each 11.00 244.05 2684.55
cement : 3 coarse sand) and a coat of neat cement, rounding the
edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC RAIN

WATER PIPES conforming to IS : 13592 Type A including jointing
3 12.41 with seal ring conforming to IS : 5382 leaving 10 mm gap for
thermal expansion.(i) Single socketed pipes.

i 12.41.2 110 mm diaMeter Metre 143.00 305.05 43622.15

Providing and fixing on wall face unplasticised - PVC moulded
fittings/ accessories for unplasticised Rigid PVC rain water pipes
conforming to IS : 13592 Type A including jointing with seal ring
4 12.42
conforming to IS : 5382 leaving 10 mm gap for thermal
expansion.

a) 12.42.1 Coupler
i 12.42.1.2 110 mm Each 30.00 117.80 3534.00
b) 12.42.5 Bend 87.5°
i 12.42.5.2 110 mm bend Each 11.00 129.85 1428.35
c) 12.42.6 Shoe (Plain)
i 12.42.6.2 110 mm Shoe Each 11.00 113.80 1251.80

BOQ Civil Works Page 16 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing false ceiling at all height including providing

and fixing of frame work made of special sections, power
pressed from M.S. sheets and galvanized with zinc coating of 120
gms/sqm (both side inclusive) as per IS : 277 and consisting of
angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27
mm and 37mm, at 1200 mm centre to centre, one flange fixed to
the ceiling with dash fastener 12.5 mm dia x 50mm long with
6mm dia bolts, other flange of cleat fixed to the angle hangers of
5 12.45 25x10x0.50 mm of required length with nuts & bolts of required
size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm
centre to centre, to which the ceiling section 0.5 mm thick
bottom wedge of 80 mm with tapered flanges of 26 mm each
having lips of 10.5 mm, at 450 mm centre to centre, shall be
fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64

mm dia x 230 mm long G.I. wire at every junction, including
fixing perimeter channels 0.5 mm thick 27 mm high having
flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed
to wall/partition with the help of rawl plugs at 450 mm centre,
with 25mm long dry wall screws @ 230 mm interval, including
fixing of gypsum board to ceiling section and perimeter channel
with the help of dry wall screws of size 3.5 x 25 mm at 230 mm
c/c, including jointing and finishing to a flush finish of tapered
and square edges of the board with recommended jointing
compound , jointing tapes , finishing with jointing compound in 3
layers covering upto 150 mm on both sides of joint and two
coats of primer suitable for board, all as per manufacturer's
specification and also including the cost of making openings for
light fittings, grills, diffusers, cutouts made with frame of
perimeter channels suitably fixed, all complete as per drawings,
specification and direction of the Engineer in Charge but
excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

i 12.45.3 Sqm 1157.46 1286.20 1488722.02
Providing and Fixing 15 mm thick densified tegular edged eco
friendly light weight calcium silicate false ceiling tiles of
approved texture of size 595 x 595 mm in true horizontal level,
suspended on inter locking metal grid of hot dipped galvanised
steel sections (galvanising @ 120 grams per sqm including both
side) consisting of main ‘T’ runner suitably spaced at joints to get
required length and of size 24x38 mm made from 0.33 mm thick
(minimum) sheet, spaced 1200 mm centre to centre, and cross
“T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet,
1200 mm long spaced between main’T’ at 600 mm centre to
6 12.53 centre to form a grid of 1200x600mm and secondary cross ‘T’ of
length 600 mm and size 24 x28 mm made of 0.33 mm thick
(Minimum) sheet to be inter locked at middle of the 1200x 600
mm panel to from grid of size 600x600 mm, resting on periphery
walls /partitions on a Perimeter wall angle pre-coated steel of
size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet
with the help of rawl plugs at 450 mm centre to centre with
25mm long dry wall screws @ 230 mm interval and laying

15 mm thick densified edges calicum silicate ceiling tiles of

approved texture in the grid, including, cutting/ making opening
for services like diffusers, grills, light fittings, fixtures, smoke
detectors etc., wherever required. Main ‘T’ runners to be
suspended from ceiling using G.I. slotted cleats of size 25x35x1.6
mm fixed to ceiling with 12.5 mm dia and 50 mm long dash
fasteners, 4 mm G.I. adjustable rods with galvanised steel level
clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to
centre along main ‘T’, bottom exposed with 24 mm of all
Tsections shall be pre-painted with polyster baked paint, for all
heights, as per specifications, drawings and as directed by
Engineer-in-Charge.

BOQ Civil Works Page 17 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Note :- Only calcium silicate false ceiling area will be measured

from wall to wall. No deduction shall be made for exposed
frames/ opening (cut outs) having area less than 0.30 sqm.The
calcium silicate ceiling tile shall have NRC value of 0.50
Sqm 687.57 1643.95 1130337.52
(Minimum), light reflection > 85%, non- combustible as per B.S.
476 part IV, 100% humidity resistance and also having thermal
conductivity <0.043 w/ mK.

Providing and fixing GI Clip-in Metal Ceiling System of 600x600

mm module which includes providing and fixing wall angle ('C'
shaped of size 20x30x20 mm made of 0.5 mm thick or 'L shaped
of size of min 19 x 19 made of 0.3mm thick ) pre painted steel
along the perimeter of the room with help of nylon sleeves and
wooden screws at 300 mm center to centre, suspending the
main carrier ( main carrier to be either C shaped of size
10x38x10 mm made of G.I steel 0.7 mm thick or Inverted
triangle shaped spring Tee of size 24 mm x 34 mm and made of
GI steel of thickness 0.45mm or 15 mm x 37 mm and made of GI
steel of thickness 0.5mm ) and width from the soffit with help of
7 12.54 soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm bullet
fasteners of size 40 mm long and 10mm dia, 6mm dia GI
threaded rod and carrier suspension clip and main carrier
bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee of
size 24 mm x 34 mm and made of GI steel of thickness 0.45mm
or 15 mm x 37 mm and made of GI steel of thicknese to centre
with 25mm long dry wall screws @ 230 mm interval and laying
oved quality, all complete as per approved drawing & direction
of Engineer-in-Charge. (Single / double glass panes and silicon
sealent shall be paid separately).
Note

All sections to be galvanized @ 120 gms/sqm (both side

inclusive). The item includes making required cutting/making,
opening for services like diffusers, grills, light fittings, fixtures,
smoke detectors etc. and providing and fixing with clip in tiles
into spring ‘T’ with
GI Metal Ceiling Clip in plain Beveled edge global white color tiles
of size 600x600 and 0.5 mm thick with 25 mm height, made of G
I sheet having galvanizing of 100 gms/ sqm (both sides inclusive)
and 20% perforation area with 1.8 mm dia holes and having NRC
a) 12.54.2 Sqm 50.00 1881.60 94080.00
of 0.5, electro statically polyester powder coated of thickness 60
microns (minimum), including factory painted after bending and
perforation.

Providing and applying two coats of High Albedo paint having

minimum Solar Reflective Index (SRI) 108 (with solar reflectance
& thermal emittance tested as per ASTM) C 1549 and ASTM C
1371 respectively), VOC less than 10 cc/gm. The coating
thickness and the methodology of application shall strctly as per
manufacturer's specifications and as approved by Engineer-in-
8 12.63 Charge. Surface preparation includes cleaning with metal wire Sqm 609.90 314.85 192025.44
brush to remove all dust, fungus etc., washing with water all
complete. The contractor shall give guarantee for the
perfomance of SRI and also the durabitity of coating, all
complete as per direction of Engineer-in-Charge.

Providing and fixing precoated galvanised iron profile sheets

(size, shape and pitch of corrugation as approved by Engineer-in-
charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc
coating 120 grams per sqm as per IS: 277, in 240 mpa steel
grade, 5-7 microns epoxy primer on both side of the sheet and
polyester top coat 15-18 microns. Sheet should have protective
guard film of 25 microns minimum to avoid scratches during
9 12.50 transportation and should be supplied in single length upto 12 Sqm 80.93 627.55 50790.13
metre or as desired by Engineer-in-charge. The sheet shall be
fixed using self drilling /self tapping screws of size (5.5x 55 mm)
with EPDM seal, complete upto any pitch in horizontal/ vertical
or curved surfaces, excluding the cost of purlins, rafters and
trusses and including cutting to size and shape wherever
required.

BOQ Civil Works Page 18 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing precoated galvanised steel sheet roofing

accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc
coating 120 grams per sqm as per IS: 277, in 240 mpa steel
10 12.51 grade, 5-7 microns epoxy primer on both side of the sheet and
polyester top coat 15- 18 microns using self drilling/ self tapping
screws complete :

i 12.51.1 Ridges plain (500 - 600mm) Rmt 8.78 416.30 3655.95

ii 12.51.4 Barge board (Upto 300 mm) Rmt 8.10 356.50 2887.65
iii 12.51.6 Gutter (600 mm over all girth) Rmt 34.30 1041.75 35732.03

TOTAL (Carried Over to Summary of Civil Works) 3091795.83 0.00

J 13.0 FINISHING WORK

1 13.4 12 mm cement plaster of mix :
i 13.4.1 1:4 (1 cement: 4 coarse sand) Sqm 3145.54 276.15 868641.95
15 mm cement plaster on rough side of single or half brick wall
2 13.5
of mix :
i 13.5.2 1:6 (1 cement: 6 coarse sand) Sqm 3145.54 303.90 955930.79
3 13.6 20 mm cement plaster of mix :
i 13.6.1 1:4 (1 cement: 4 coarse sand) Sqm 1912.85 379.70 726309.71
4 13.16 6 mm cement plaster of mix :
i 13.16.1 1:3 (1 cement: 3 fine sand) Sqm 2172.63 227.35 493946.98
Extra for providing and mixing water proofing material in cement per bag of
plaster work in proportion recommended by the manufacturers. 50KG
5 13.21 Cement 1504.00 59.75 89864.00
Used in
Mix
Extra for plastering exterior walls of height more than 10 m from
6 13.22 ground level for every additional height of 3 m or part thereof.

i i 10m to 13m Sqm 185.87 65.95 12257.99

ii ii 13m to 16m Sqm 176.04 131.90 23219.06
iii iii 16m to 19m Sqm 330.33 197.85 65355.79
iv iv 19m to 22m Sqm 216.74 263.80 57176.43
v v 22m to 25m Sqm 429.41 329.75 141597.81
Providing and applying plaster of paris putty of 2 mm thickness
7 13.26 over plastered surface to prepare the surface even and smooth Sqm 1157.46 196.70 227671.92
complete.
White washing with lime to give an even shade : New work
8 13.37.1 Sqm 2172.63 28.55 62028.53
(three or more coats)
Distempering with 1st quality acrylic distemper (ready mixed)
having VOC content less than 50 gms/litre, of approved
9 13.42.1 manufacturer, of required shade and colour complete, as per Sqm 1157.46 87.15 100872.43
manufacturer’s specification. Two or more coats on new work.

Finishing walls with textured exterior paint of required shade

:New work (Two or more coats applied @ 3.28 ltr/10 sqm) over
10 13.45.1 Sqm 1190.37 232.00 276165.58
and including priming coat of exterior primer applied @
2.20kg/10 sqm
Wall painting with premium acrylic emulsion paint of interior
grade, having VOC (Volatile Organic Compound ) content less
11 13.83 than 50 grams/ litre of approved brand and manufacture,
including applying additional coats wherever required to achieve
even shade and colour.
i 13.83.2 Two coats Sqm 3949.15 113.90 449808.13
Providing and applying white cement based putty of average
thickness 1 mm, of approved brand and manufacturer, over the
12 13.80 Sqm 7099.46 115.15 817502.90
plastered wall surface to prepare the surface even and smooth
complete.
Applying priming coats with primer of approved brand and
13 13.85 manufacture, having low VOC (Volatile Organic Compound )
content.
With ready mixed pink or grey primer on wood work
i 13.85.1 (hard and soft wood) having VOC content less than 50grams/ Sqm 63.50 57.05 3622.68
litre
With water thinnable cement primer on wall surface
ii 13.85.3 Sqm 5909.09 60.00 354545.51
having VOC content less than 50 grams/litre
Painting with synthetic enamel paint of approved brand and
14 13.61 manufacture to give an even shade :

i 13.61.1 Two or more coats on new work Sqm 367.27 121.55 44641.55

BOQ Civil Works Page 19 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Wall painting with premium anti bacterial paint of interior grade,

having VOC (Volatile Organic Compound ) content less than
Derived item 50grams/ litre of approved brand and manufacture, including
15 Sqm 1959.94 149.70 293403.36
(13.82.2) applying additional coats wherever required to achieve even
shade and colour.Two coats

TOTAL (Carried Over to Summary of Civil Works) 5771159.73 293403.36

K 16.0 ROAD WORK

Preparation and consolidation of sub grade with power road
roller of 8 to 12 tonne capacity after excavating earth to an
average of 22.5 cm. depth, dressing to camber and consolidating
1 16.1 with road roller including making good the undulations etc. and Sqm 321.00 156.75 50316.75
re roller including making good the undulations etc. and re-
rolling the sub grade and disposal of surplus earth lead upto 50
metres.
Supplying and Stacking of Good Earth by mechanical transport
2 16.3.9 including loading, unloading including royalty & carriage up to 5 Cum 24.00 483.90 11613.60
KM complete.
Extra for compaction of earth work in embankment under
3 16.2 optimum moisture conditions to give at least 95% of the Cum 24.00 18.20 436.80
maximum dry density (proctor density).
Construction of granular sub-base by providing close graded
Material conforming to specifications, mixing in a mechanical
mix plant at OMC, carriage of mixed material by tippers to work
site, for all leads & lifts, spreading in uniform layers of specified
4 16.78 thickness with motor grader on prepared surface and
compacting with vibratory power roller to achieve the
desired density, complete as per specifications and directions of
Engineerin- Charge.

With material conforming to Grade-I (size range 75 mm to 0.075

i 16.78.1 Cum 48.00 2517.70 120849.60
mm) having CBR Value-30
Providing and laying design mix cement concrete of M-30 grade,
in roads/taxi tracks/ runways, using cement content as per
design mix, using coarse sand and graded stone aggregate of 40
mm nominal size in appropriate proportions as per approved &
specified design criteria, providing dowel bars with sleeve/ tie
bars wherever required, laying at site, spreading and compacting
mechanically by using needle and surface vibrators, levelling to
required slope/ camber, finishing with required texture,
including steel form work with sturdy M.S. channel sections,
curing, making provision for contraction/ expansion,
5 16.43
construction & longitudinal joints ( 10 mm wide x50 mm deep)
by groove cutting machine, providing and filling joints with
approved joint filler and sealants, complete all as per direction of
Engineerin- charge (Item of joint fillers, sealants, dowel bars with
sleeve/ tie bars to be paid separately). Note:-Cement content
considered in M-30 is @ 340 kg/cum. Excess/ less cement used
as per design mix is payable/ recoverable separately.

Cement concrete manufactured in automatic batching plant

i 16.43.2 (RMC plant) i/c transportation to site in transit mixer Cum 41.00 9153.75 375303.75

Extra for providing and mixing hardening compound of approved

6 16.44 quality as per manufacturer’s specification in cement concrete. Litre 23.00 50.85 1169.55

Providing and fixing in position pre-moulded joint filler in per cm

expansion joints. depth
per cm
7 16.45 116.00 3.10 359.60
width
per m
length
Providing and laying in position bitumen hot sealing compound
depth per
for expansion joints etc. Using grade ‘A’ sealing compound.
cm width
8 16.46.1 116.00 3.30 382.80
per m
length

Painting runway/taxi track/apron marking with adequate nos of

coats to give uniform finish with road marking paint of superior
make as approved by the Engineer-in-charge, i/c cleaning the
9 16.47
surface of all dirt, scales, oil, grease and other foreign material
etc. and lining out complete.

BOQ Civil Works Page 20 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

i 16.47.1 New work (Two or more coats) Sqm 20.00 150.85 3017.00
Providing, laying and making kerb channel 30 cm wide and 50
mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6
graded stone aggregate 20 mm nominal size) over 75mm bed of
10 16.63 dry brick ballast 40 mm nominal size, well rammed and Sqm 50.00 483.00 24150.00
consolidated and grouted with fine sand, including finishing the
top smooth etc. complete and as per direction of Engineer-in-
charge.
Providing and laying at or near ground level factory made kerb
stone of M-25 grade cement concrete in position to the required
line, level and curvature, jointed with cement mortar 1:3 (1
cement: 3 coarse sand), including making joints with or without
grooves (thickness of joints except at sharp curve shall not to
11 16.69 more than 5mm), including making drainage opening wherever Cum 5.00 8376.15 41880.75
required complete etc. as per direction of Engineer-in-charge
(length of finished kerb edging shall be measured for payment).
(Precast C.C. kerb stone shall be approved
by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement

Concrete paver blocks in footpath, parks, lawns, drive ways or
light traffic parking etc, of required strength, thickness & size/
shape, made by table vibratory method using PU mould, laid in
required colour & pattern over 50mm thick compacted bed of
sand, compacting and proper embedding/laying of inter locking
paver blocks into the sand bedding layer through vibratory
12 16.91.1 compaction by using plate vibrator, filling the joints with sand Sqm 50.00 884.75 44237.50
and cutting of paver blocks as per required size and pattern,
finishing and sweeping extra sand. complete all as per direction
of Engineer-in-Charge. 60mm thick cement concrete paver block
of M-35 grade with approved colour, design & pattern.

Providing and erecting 6.00 metre high temporary barricading at

site as per drawing/ direction of Engineerin- Charge which
includes writing and painting, arrangement for traffic diversion
such as traffic signals during construction at site for day and
night, glow lamps, reflective signs, marking, flags, caution tape as
directed by the Engineer-in-Charge. The barricading provided
shall be retained in position at site continuously i/c shifting of
barricading from one location to another location as many times
as required during the execution of the entire work till its
Derived item
13 completion. Rate include its maintenance for damages,painting, Rmt 160.00 6881.00 1100960.00
(16.81)
all incidentals, labour materials, equipments and works required
to execute the job. The barricading shall not be removed without
prior approval of Engineer-in-Charge. (Note :- One time payment
shall be made for providing barricading from start of work till
completion of work i/c shifting. The barricading provided shall
remain to be the property of the contractor on completion of
the work).

TOTAL (Carried Over to Summary of Civil Works) 1774677.70 0.00

L DSR-2018 HORTICULTURE AND LAND SCAPING

Supplying and stacking at site dump manure from approved
source, including carriage upto 5 km complete (manure
1 2.4
measured in stacks will be reduced by 8% for payment) :

i 2.4.2 Screened through sieve of I.S. designation 16 mm Cu.Mt. 4.00 262.05 1048.20
ii 2.4.3 Screened through sieve of I.S. designation 4.75 mm Cu.Mt. 4.00 287.75 1151.00
2 2.7 Fine dressing of the ground. Sq.Mt. 79.00 3.25 256.75
Spreading of sludge, dump manure and/or good earth in
required thickness as per direction of officer-in-charge (cost of
3 2.8 Cu.Mt. 24.00 46.15 1107.60
sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion

4 2.9 Cu.Mt. 24.00 32.10 770.40
specified or directed by the Officer-in-charge
Grassing with selection No. 1 grass including watering and
maintenance of the lawn for 60 days or more till the grass forms
5 2.10 a thick lawn, free from weeds and fit for mowing including
supplying good earth, if needed (the grass and earth shall be
paid for separately).
i 2.10.2 With grass Turf Sq.Mt. 79.00 11.70 924.30

BOQ Civil Works Page 21 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Preparation of beds for hedging and shrubbery by excavating 60

cm deep and trenching the excavated base to a further depth of
30 cm, refilling the excavated earth after breaking clods and
mixing with sludge or manure in the ratio of 8:1 (8 parts of
stacked volume of earth after reduction by 20% : one part of
stacked volume of sludge or manure after reduction by 8%),
6 2.13 flooding with water, filling with earth if necessary, watering and Cu.Mt. 5.00 195.90 979.50
finally fine dressing, leveling etc. including stacking and disposal
of materials declared unserviceable and surplus earth by
spreading and leveling as directed, within a lead of 50 m, lift up
to 1.5 m complete (cost of sludge, manure or extra earth to be
paid for separately)

Digging holes in ordinary soil and refilling the same with the
excavated earth mixed with manure or sludge in the ratio of 2:1
by volume (2 parts of stacked volume of earth after reduction by
20% : 1 part of stacked volume of manure after reduction by 8%)
7 2.14
flooding with water, dressing including removal of rubbish and
surplus earth, if any, with all leads and lifts (cost of manure,
sludge or extra good earth if needed to be paid for separately) :

i 2.14.1 Holes 1.2 m dia and 1.2 m deep Each 10.00 305.4 3053.50
ii 2.14.2 Holes 90 cm dia, and 90 cm deep Each 5.00 130.4 652.00
iii 2.14.3 Holes 60 cm dia, and 60 cm deep Each 5.00 40.0 199.75
iv 2.14.4 Holes 45 cm dia, and 45 cm deep. Each 5.00 17.1 85.50
Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m
high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and
8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25
x 6 mm M.S. flat iron rings in two halves, fixing together at site
with required six numbers of 8 mm dia and 30 mm long bolts,
including painting two coats with synthetic enamel paint of
approved brand and manufacture over a coat of primer. One
name plate of 1 mm thick M.S. sheet of size 250x100 mm shall
8 2.16 Each 15.00 3952.0 59280.00
be welded to the tree guard near the middle height and lettered
CPWD / PWD/ any other approved name. The tree guard shall be
suitably fixed to the ground by embedding four legs of tree guard
in pits of suitable dia and to a depth of 25 cm, refilling the pits
with soil and ramming, complete in all respect as per satisfaction
and direction of Officer-in-charge.

Providing and fixing M. S. tree guard 45 cm square in plan, height

1.20 metre above ground level and 0.40 metre below ground
level. The vertical members shall consist of four nos. angle iron
of size 25x25x3 mm, 1.6 m long, one at each corner and 8 nos
flat iron of size 25x3 mm, 1.2 m long. The vertical members shall
be welded to 4 nos. 25x6 mm M. S. flats placed horizontally
around the vertical member of the cage. One name plate of 1
mm thick M.S. sheet of size 250x100 mm shall be welded to the
tree guard near the middle height and lettered CPWD/ PWD/
9 2.26 Each 10.00 1949.2 19491.50
any other approved name. The tree guard shall be fixed to the
ground by making suitable holes and by embedding four corners
leg in the ground, including refilling the earth, compaction etc.
complete. The tree guard shall be painted with two or more
coats of synthetic enamel paint of approved brand and
manufacture over a coat of primer, complete in all respect.

Providing Circular Cement Concrete pots of specified size, cast

with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse
sand: 4 graded stone aggregate 6 mm nominal size), reinforced
with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S.
10 2.29 wires of 3.5 mm dia as per design, including required form work,
finishing with cement punning on exposed surface, curing for
specified period and stacking in required rows & height, all
complete as per direction of Officer-in-charge.

Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm
i 2.29.1 Each 15.00 215.5 3232.50
with wall thickness of 25.4 mm

BOQ Civil Works Page 22 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing Square Cement Concrete pots of specified size, cast

with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse
sand: 4 graded stone aggregate 6 mm nominal size), reinforced
with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S.
11 2.30 wires of 3.5 mm dia as per design, including required frame
work, finishing with cement punning on exposed surface, curing
for specified period and stacking in required rows & height, all
complete as per direction of Officer-in-charge.

Top inner width 35 cm, outer bottom width 25 cm, total height
i 2.30.1 Each 10.00 246.3 2463.00
35 cm and wall thickness 25.4 mm
Providing and laying Neelgiri/Mexican grass turf with earth
50mm to 60mm thickness of existing ground prepared with
proper level and ramming with tools wooden (Dhurmos) and
than rolling the surface with light roller make the surface
12 2.33 Sq.Mt. 79.00 211.25 16688.75
smoothen and light waterning with sprinkler and maintenance
for 30 days or more till the grass establish properly, as per
direction of officer-in-charge.

Complete maintenance of the entire garden features having as

per yard stick in the garden area i.e. lawn trees, shrubs, hedge,
flower beds, foliages, creepers etc. including hoeing,weeding
pruning replacement of plants, gap filling, watering, mowing of
lawn, grass cutting by lawn mover and brush cutter , removal of
garden waste, applying insecticide, pesticide &
fertilizers(whenever required) top dressing of lawn with good
13 2.40
earth and menure and maintenance of other garden related
works as directed by office-in-charge (Cost of Good Earth,
Manure, Fertilizer, Insecticide , Pesticide will be provided by the
Department & lawn mover and brush cutter with fuel , other T &
P material/articles shall be provided by the contractor.)

Play grounds / Public parks (as per yard stick 1 Mali =2.00Acre). Per
Sq.Mt.
i 2.40.5 79.00 2.25 177.75
Per
Month
Complete maintenance of shrubs (Out side garden features),
jobs like making of basin at regular interval i/c watering,
Per Shrub
weeding, pruning & application of fertilizer etc, (excluding the
14 2.43 Per 250.00 13.90 3475.00
cost of material which shall be supplied by the department) and
Month
as per direction of officer in charge.

Providing & fixing of White River (Stone) Pables size of 2" to

2.50" dia in natural colour at site of work including loading,
15 2.50 Qtl. 1.00 593.1 593.05
unloading, carriage and all taxes paid etc.and as per direction of
officer in charge.
Providing and applying anti termite treatment of infected trees
i/c all branches/leaves by spraying chemical emulsion 0.5%
(Chlorpyriphos 20% EC) concentration through power spray
Each
16 2.55 machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) 25.00 57.6 1438.75
Tree
and as per direction of officer-in-charge.and as per direction of
officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P.

one liter premise diluted in 499 liters water and applying
solution @ 1.00 litre solution per sqm lawn or bed area.(two
17 2.56 Sq.Mt. 79.00 7.45 588.55
application) i/c cost of chemical)and as per direction of officer-in-
charge.and as per direction of officer-in-charge.

18 4.0 Rose Plants

Providing and Displaying plants Budded Rose (H.T. variety) 3 to 4
healthy branch 30 cm and above ht. well developed with one
i 4.91 Each 10.00 32.8 328.00
and above flower plant in 20 cm Earthen Pot, as per direction of
the officer-in-charge.
Providing and Displaying plants Creeper Rose variety 3 to 4
healthy branch 60 cm and above ht. well developed with one
ii 4.92 Each 5.00 75.9 379.25
and above flowers in 25 cm Earthen Pot, as per direction of the
officer-in-charge.
Providing and Displaying plants Standard Rose (H.T. variety) 3 to
4 healthy branch 90 cm and above ht. well developed with one
iii 4.93 Each 5.00 150.7 753.50
and above flowers in 25 cm Earthen Pot, as per direction of the
officer-in-charge.
19 5.0 Ornamental Plants

BOQ Civil Works Page 23 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and Displaying Acalypha plant Different colour well

developed, fresh & healthy with good foliage, multi branch 30 to
i 5.1 45 cm ht. in 20 cm size of Earthen Pot/ Plastic Pot bushy plant as Each 5.00 35.9 179.50
per direction of the officer-in-charge.

Providing and Displaying Acalypha red plant well developed with

fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic
ii 5.3 Each 7.00 41.0 287.00
Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus reginold piller type Topiary plant

well developed with fresh & healthy 210 to 240 cm ht in 40 cm
iii 5.26 Each 2.00 2460.0 4920.00
Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra,

Thima, Marry palmar, Cherry Blossom etc. well developed with
iv 5.12 fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 Each 5.00 322.9 1614.50
cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus Long Island topiary plant well

developed with fresh & healthy 5 to 6 ball specific size and shape
v 5.21 Each 2.00 1230.0 2460.00
120 to 150 cm ht in 40 cm Cement Pot as per direction of the
officer-in-charge.
20 6.0 Ground Covers Plants
Providing and Displaying of Clerodendron inerme plant of ht. 30
cm to 40 cm multi branched in 25 cm size of Earthen Pot / Plastic
i 6.7 Each 5.00 20.5 102.50
Pot & as per direction of the officer-in-charge.

Providing and Displaying of Iresine herbstii plant, of height 20-30

cm., full of branches well developed in 20 cm size of Earthen Pot
ii 6.17 Each 10.00 20.5 205.00
/ Plastic Pot & as per direction of the officer-in-charge..

Providing and Displaying of Wadelia trilobata plant,full of leaves

iii 6.30 in 15 cm size of Poly bags & as per direction of the officer-in- Each 5.00 15.4 77.00
charge.
21 7.0 Tree Plants
Supply and stacking of Alstonia scholaris plant of height 150-165
i 7.4 cm. in bag of size 25 cm as per direction of the officer-in-charge. Each 10.00 65.0 650.00

Supply and stacking of Bauhinia blakeana (Kachnar) plant of

ii 7.7 height 120- 150 cm. in big poly bags of size 25 cm as per Each 5.00 80.0 400.00
direction of the officer-in-charge.
Supply and stacking of Ficus benjamina (green) plant of height
150-165 cm., bushy with healthy branches and lush green foliage
iii 7.27 Each 4.00 180.0 720.00
in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Ficus religiosa (Peepal) plant of height 150-

iv 7.36 165 cm. in big poly bags of size 30 cm as per direction of the Each 2.00 65.0 130.00
officer-in-charge.
Supply and stacking of Nauclea cadamba (Kadam) plant of height
v 7.60 150-165 cm. in big poly bag of size 25 cm as per direction of the Each 5.00 65.0 325.00
officer-in-charge.v
Supply and stacking of Plumeria acutifolia plant of height 150-
vi 7.68 165 cm. with 3-4 branches in big size HDPE bag as per direction Each 2.00 200.0 400.00
of the officer-in-charge.
Supply and stacking of Washingtonia filifea palm plant stem ht.
120-135 cm with 8-10 healthy leaves lush green leaves well
vii 7.90 Each 5.00 650.0 3250.00
developed in big size HDPE Bags as per direction of the officer-in-
charge.
22 8.0 SHRUBS
Supply and stacking of plant Caesalpinia pulcherrima species of
i 8.4 height 45-60 cm. in earthen pot of size 20 cm as per direction of Each 10.00 45.0 450.00
the officer-in-charge.
Supply and stacking of plant Calliandra hybrida of height 105-120
ii 8.7 cm., well branched, bushy in big size HDPE bag as per direction Each 15.00 90.0 1350.00
of the officer-in-charge.
Supply and stacking of plant Hamelia patens of height 30-45 cm.
iii 8.31 with 3-4 branches in poly bags of size 20 cm as per direction of Each 10.00 20.0 200.00
the officer-in-charge.
Supply and stacking of plant Hibiscus rosasinensis of height 45-
iv 8.35 60 cm. with 3-4 branches in earthen pots of size 20 cm as per Each 5.00 35.0 175.00
direction of the officer-in-charge.
Supply and stacking of plant Tabernaemontana coronaria
v 8.60 (Chandni single) of height 90-105 cm,bushy in big size HDPE bag Each 5.00 80.0 400.00
as per direction of the officer-in-charge.
Supply and stacking of plant Tecoma gaudichaudi of height 90-
vi 8.69 105 cm.,bushy in big size HDPE bag as per direction of the officer- Each 7.00 110.0 770.00
in-charge.

BOQ Civil Works Page 24 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

TOTAL (Carried Over to Summary of Civil Works) 138183.60 0.00

M 21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS : 1285, fixed with
rawl plugs and screws or with fixing clips, or with expansion hold
fasteners including necessary filling up of gaps at junctions, at
top, bottom and sides with required PVC/neoprene felt etc.
1 21.1 Aluminium sections shall be smooth, rust free, straight, mitred
and jointed echanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P. brass /
stainless steel screws, all complete as per architectural drawings
and the directions of Engineer-in-charge. Glazing and paneling
to be paid for separately) :

a) 21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder
i 21.1.1.2 kg 10.00 456.30 4563.00
coating 50 micron)
For shutters of doors, windows & ventilators including providing
and fixing hinges/ pivots and making provision for fixing of
2 21.1.2 fittings wherever required including the cost of EPDM rubber /
neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder

i 21.1.2.2 kg 15.00 546.35 8195.25
coating 50 micron)
Providing and fixing 12 mm thick prelaminated particle board flat
pressed three layer or graded wood particle board conforming
to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors,
3 21.2 windows shutters and partition frames with C.P. brass / stainless
steel screws etc. complete as per architectural drawings and
directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both

i 21.2.2 Sqm 1.05 1046.90 1099.25
sides
Providing and fixing glazing in aluminium door, window,
ventilator shutters and partitions etc. with EPDM rubber /
4 21.3 neoprene gasket etc. complete as per the architectural drawings
and the directions of engineer-in-charge . (Cost of aluminium
snap beading shall be paid in basic item):
With float glass panes of 5 mm thickness (weight not less than
i 21.3.2 Sqm 0.50 1296.40 648.20
12.50 kg/ sqm)
With float glass panes of 8 mm thickness (weight not less than
ii 21.3.3 Sqm 1.05 1462.35 1535.47
20 kg/ sqm)
Derived With clear toughened glass panes of 6 mm thickness
iii Sqm 1.00 1699.80 1699.8
Item (21.3)
Derived With clear toughened glass panes of 8 mm thickness
iv Sqm 65.67 2191.25 143892.08
Item (21.3)

Filling the gap in between aluminium frame and adjacent

RCC/Brickwork/ Stone Work by providing weather silicon sealant
5 21.8
over backer rod of approved quality as per architectural
drawings and direction of Engineer-in-charge

i 21.8.1 Upto 5mm depth and 5mm width metre 358.00 79.45 28443.10
Providing and fixing 12 mm thick frameless toughened glass door
shutter of approved brand and manufacture, including providing
and fixing top & bottom pivot & double action hydraulic floor
spring type fixing arrangement and making necessary holes etc.
6 21.18 for fixing required door fittings, including all patch fittings all Sqm 68.00 4447.90 302457.20
complete as per drawings, direction of Engineer-in-charge (Door
handle, lock and stopper etc. to be paid separately).

Providing and fixing Stainless steel 304 Grade H- type pull handle
of size min 32 mm dia and 1200mm long of approved make
7 NSI-37 including SS screws, including making holes of required size in Each 62.00 8705.65 539750.3
shutter etc. complete as per direction of Engineer-in-Charge.

Providing and fixing SS Bottom patch Lock with cylinder of

8 NSI-38 approved make including necessary screws etc. all complete. Each 18.00 3645.20 65613.6

BOQ Civil Works Page 25 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing SS floor mounted half dome door stopper of

9 NSI-39 dia 45mm including necessary screws etc. all complete. Each 31.00 557.50 17282.5

Providing and fixing self adhesive type frosted glass film of 3M

make or approved equivalent, in required pattern over glass etc.
as per drawings, including cleaning the receiving surface of glass
10 NSI-40
etc., all complete as per manufacturer's specification and
direction of Engineer in charge:

i i Plain frosted film Sqm 78.33 1844.05 144452.00

ii ii Colored frosted film Sqm 78.33 2152.80 168637.65
Providing and fixing 12mm thk. Toughened float glass glazing cut
and fixed in openings of desired shape as per drawing with 3/4"
beveling all around, fixed with the help of SS patch fittings, with
top and bottom 'C' channels, fixed firmly to the slab/ MS
11 NSI-41 Structure ,as directed by Engineer in Charge. Area of openings to Sqm 391.67 5170.05 2024956.09
be measured). Assume frameless glass. Rate of above item to
include P/F of : 20x20mm "C" channel SS patch Fittings.

Providing and supplying aluminium extruded tubular and other

aluminium sections as per the architectural drawings and
approved shop drawings , the aluminium quality as per grade
6063 T5 or T6 as per BS 1474, including super durable powder
coating of 60-80 microns conforming to AAMA 2604 of required
colour and shade as approved by the Engineer-in-Charge. ( The
12 25.1 item includes cost of material such as cleats, sleeves, fasteners Kg 5368.71 370.45 1988838.51
screws etc as desired. necessary for fabrication of extruded
aluminium frame work. Nothing extra shall be paid on this
account).
The weight of aluminium extruded section shall be taken for
purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in

position semi (grid) unitized system of structural/ curtain wall
13 25.2 glazing (with open joints) for linear as well as curvilinear portions Sqm 894.78 2949.30 2638989.25
of the building for all heights and all levels, including :

a) Structural analysis & design and preparation of shop drawings

for the specified design loads conforming to IS 875 part III (the
system must passed the proof test at 1.5 times design wind
pressure without any failure), including functional design of the
aluminum sections for fixing glazing panels of various
thicknesses, aluminium cleats, sleeves and splice plates etc.
gaskets, screws, toggles, nuts, bolts, clamps etc., structural and
weather silicone sealants, flashings, fire stop (barrier)-cum-
smoke seals, microwave cured EPDM gaskets for water
tightness, pressure equalization & drainage and protection
against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanized /

Aluminium alloy of 6005 T5 brackets of required sizes, sections
and profiles etc. to accommodate 3 Dimensional movement for
achieving perfect verticality and fixing structural glazing system
rigidly to the RCC/ masonry/structural steel framework of
building structure using stainless steel anchor fasteners/ bolts,
nylon separator to prevent bimetallic contacts with nuts and
washers etc. of stainless steel grade 316, of the required
capacity and in required numbers..

c) Providing and filling, two part pump filled, structural silicone

sealant and one part weather silicone sealant compatible with
the structural silicone sealant of required bite size in a clean and
controlled factory / work shop environment , including double
sided spacer tape, setting blocks and backer rod, all of approved
grade, brand and manufacture, as per the approved sealant
design, within and all around the perimeter for holding glass

d) Providing and fixing in position flashings of solid aluminium

sheet 1 mm thick and of sizes, shapes and profiles, as required as
per the site conditions, to seal the gap between the building
structure and all its interfaces with curtain glazing to make it
watertight.

BOQ Civil Works Page 26 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

e) Making provision for drainage of moisture/ water that enters

the curtain glazing system to make it watertight, by
incorporating principles of pressure equalization, providing
suitable gutter profiles at bottom (if required), making necessary
holes of required sizes and of required numbers etc. complete.
This item includes cost of all inputs of designing, labour for
fabricating and installation of aluminium grid, installation of
glazed units, T&P, scaffolding and other incidental charges
including wastages etc., enabling temporary structures and
services, cranes or cradles etc. as described above and as
specified. The item includes the cost of getting all the structural
and functional design including shop drawings checked by a
structural designer, dully approved by Engineer-in-charge.

The item also includes the cost of all mock ups at site, cost of all
samples of the individual components for testing in an approved
laboratory, field tests on the assembled working structural
glazing as specified, cleaning and protection till the handing over
of the building for occupation. In the end, the Contractor shall
provide a water tight structural glazing having all the
performance characteristics etc. all complete as required, as per
the Architectural drawings, as per item description, as specified,
as per the approved shop drawings and as directed by the
Engineer in-Charge.

Note:- 1. The cost of providing extruded aluminium frames,

shadow boxes, extruded aluminium section capping for fixing in
the grooves of the curtain glazing and vermin proof stainless
steel wire mesh shall be paid for separately under relevant items
under this subhead. However, for the purpose of payment, only
the actual area of structural/ curtain wall glazing (including width
of grooves ) on the external face shall be measured in sqm. up to
two decimal places.

Providing, assembling and supplying vision glass panels (IGUs)

comprising of hermetically-sealed 6-12- 6 mm insulated glass
(double glazed) vision panel units of size and shape as required
and specified, comprising of an outer heat strengthened (as
approved) glass 6mm thick, of approved colour and shade with
reflective soft coating on surface # 2 of approved colour and
shade, an inner heat strengthened (as approved) clear float glass
6mm thick, spacer tube 12mm wide, desiccants, including
primary seal and secondary seal (structural silicone sealant) etc.
all complete for the required performances, as per the
Architectural drawings, as per the approved shop drawings, as
14 25.3 specified and as directed by the Engineer-in-Charge. The IGUs
shall be assembled in the factory/ workshop of the glass
processor.
(Payment for fixing of IGU Panels in the curtain glazing is
included in cost of item No.1.8.16 above).
For payment, only the actual area of glass on face # 1 of the glass
panels (excluding the areas of the grooves and weather silicone
sealant) provided and fixed in position, shall be measured in
sqm. (To be fixed on extruded aluminium sections. and cost of
aluminium sections to be paid in relevant item)

(i) Coloured tinted float glass 6mm thick Heat Strengthened

substrate with reflective soft coating on face # 2, + 12mm Airgap
+ 6mm Heat Strengthened clear Glass of approved make having
properties as visible Light transmittance (VLT) of 25 to 35 %,
i i Sqm 894.78 3250.95 2908901.13
Light reflection internal 10 to 15%, light reflection external 10 to
20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3
W/m2 degree K etc.

Extra for openable side / top hung vision glass panels

(IGUs/laminated glass) including providing and supplying at site
all accessories and hardware for the openable panels as
specified and of the approved make such as heavy duty stainless
steel friction hinges, min 4 -point cremone locking sets with
15 25.4 stainless steel plates, handles, buffers etc. including necessary Sqm 89.48 3163.10 283029.43
stainless steel screws/ fasteners, nuts, bolts, washers etc. all
complete as per the Architectural drawings, as per the approved
shop drawings, as specified and as directed by the Engineer in-
Charge..

BOQ Civil Works Page 27 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing, fabricating and supplying shadow box of required size

and shape, for fixing in the spandrel portion of the structural
glazing, in linear as well as curvilinear portions of the building by
providing semi -rigid, inorganic, non-combustible fibre glass wool
insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part
5. The insulation layer shall have facing (factory bonded on
surface # 1 of the fibre glass insulation layer), of black non-
16 25.5 woven fibre glass tissue of nominal thickness 0.5 mm and sqm 10.00 1883.55 18835.50
nominal mass not less than 60 gm /sqm, made of randomly
oriented glass fibres distributed in a binder by a wet-lay process
including fixing 1.5 mm thick solid aluminum sheet backing using,
6 mm thick cement board including SS rivets, nuts, bolts,
washers etc complete.

Providing and supplying Spandrel Glass Panels comprising of 6

mm thick heat strengthened monolithic float glass of approved
colour and shade with reflective soft coating on surface # 2 of
approved colour and shade so as to match the colour and shade
17 25.6 of the IGUs in the vision panels etc. ,all complete for the
required performances as specified, as per the Architectural
drawings, as per the approved shop drawings, as specified, and
as directed by the Engineer- in-Charge.

For payment, only the actual area of glass on face # 1 of the glass
panels (but excluding the area of grooves and weather silicone
sealant) provided and fixed in position, shall be measured in
sqm. (Payment for fixing of Spandrel Glass Panels in the curtain
glazing is included in cost of relevent Item*).“(i) Coloured tinted
float glass 6mm thick substrate with reflective soft coating on
face # 2, having properties as visible Light transmittance (VLT) of
sqm 5.00 2127.95 10639.75
25 to 35 %, Light reflection internal 10 to 15%, light reflection
external 10 to 20 %, shading coefficient (0.25- 0.28) and U value
of 3.0 to 3.3 W/m2 K etc. . The properties of performance glass
shall be decided by technical sanctioning authority as per the site
requirement.

TOTAL (Carried Over to Summary of Civil Works) 8196175.03 3106284.03

N 22.0 WATER PROOFING

Providing and laying water proofing treatment to vertical and
1 22.3 horizontal surfaces of depressed portions of W.C., kitchen and
the like consisting of :

(i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with
water proofing compound conforming to IS 2645 in
recommended proportions including rounding off junction of
vertical and horizontal surface. (ii) IInd course of 20mm cement
plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing
compound in recommended proportion including rounding off
i junction of vertical and horizontal surface. (iii) IIIrd course of Sqm 179.09 705.70 126383.41
applying blown or residual bitumen applied hot at 1.7 Kg. per
sqm of area. (iv) IVth course of 400 micron thick PVC sheet.
(Overlaps at joints of PVC sheet should be 100 mm wide and
pasted to each other with bitumen @ 1.7 Kg/sqm.)

BOQ Civil Works Page 28 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and laying integral cement based water proofing

treatment including preparation of surface as required for
treatment of roofs, balconies, terraces etc consisting of following
operations: (a) Applying a slurry coat of neat cement using 2.75
kg/sqm of cement admixed with water proofing compound
conforming to IS. 2645 and approved by Engineer-in-charge over
the RCC slab including adjoining walls upto 300 mm height
including cleaning the surface before treatment. (b) Laying brick
bats with mortar using broken bricks/brick bats 25mm to 115
mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse
2 22.7 sand) admixed with water proofing compound conforming to IS :
2645 and approved by Engineer-in-charge over 20 mm thick
layer of cement mortar of mix 1:5 (1 cement :5 coarse sand )
admixed with water proofing compound conforming to IS : 2645
and approved by Engineer-in-charge to required slope and
treating similarly the adjoining walls upto 300 mm height
including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of

cement slurry using 2.75 kg/ sqm of cement admixed with water
proofing compound conforming to IS : 2645 and approved by
Engineerin-charge. (d) Finishing the surface with 20 mm thick
jointless cement mortar of mix 1:4 (1 cement :4 coarse sand)
admixed with water proofing compound conforming to IS : 2645
and approved by Engineerin-charge including laying glass fibre
cloth of approved quality in top layer of plaster and finally
finishing the surface with trowel with neat cement slurry and
making pattern of 300x300 mm square 3 mm deep. (e) The
whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test.“All
above operations to be done in order and as directed and
specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum

i 22.7.1 thickness at khurra as 65 mm. Sqm 609.90 1398.50 852938.16

Providing and applying integral crystalline slurry of hydrophilic in

nature for waterproofing treatment to the RCC structures like
retaining walls of the basement, water tanks, roof slabs,
podiums, reservior, sewage & water treatment plant, tunnels /
subway and bridge deck etc., prepared by mixing in the ratio of 5
: 2 (5 parts integral crystalline slurry : 2 parts water) for vertical
surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part
water) for horizontal surfaces and applying the same from
negative (internal) side with the help of synthetic fiber brush.
The material shall meet the requirements as specified in ACI-212-
3 22.23 3R-2010 i.e by reducing permeability of concrete by more than
90% compared with control concrete as per DIN 1048 and
resistant to 16 bar hydrostatic pressure on negative side. The
crystalline slurry shall be capable of self-healing of cracks up to a
width of 0.50mm. The work shall be carried out all complete as
per specification and the direction of the engineerin- charge. The
product performance shall carry guarantee for 10 years against
any leakage.

i 22.23.1 For vertical surface two coats @0.70 kg per sqm Sqm 1601.25 484.45 775726.14
ii 22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sqm 1111.00 373.40 414848.91
Providing and applying of swellable type water stop tape, 19mm
x 25mm thick in linear meter (expansive nature) for construction
joints treatment of RCC structure such as raft slab, retaining
walls, water storage tank and at the junctions of raft slab with
the retaining walls etc.. After cleaning the surface, one coat of
required primer for swellable water stop tape shall be applied
throughout the length of the joint @3.78 litre per 240 running
4 22.26 Metre 543.03 552.20 299860.06
meter. Over the primed surface swellable type water stop tape
shall be placed. The work shall be carried out all complete as per
specification and the direction of the engineer-in-charge. The
product performance shall carry guarantee for 10 years against
any leakage.

BOQ Civil Works Page 29 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

TOTAL (Carried Over to Summary of Civil Works) 2469756.68 0.00

O MISCELLANEOUS WORKS
Providing and fixing certified restroom cubicle system of
approved make comprising of green guard certified solid
compact laminated water proof board, minimum 18 mm thick
made as per IS: 2046 (phenolic core board) and as per BS-476/97
for fire retardant for toilet showers, water closet etc . The board
shall be manufactured under high pressure and temperature by
impregnating kraft papers and outer decorative papers with
thermosetting phenolic/ melamine resins (low VOC). The cubicle
system shall be resistant towards water, chemical, scratch,
impact and heat and shall be anti bacterial, colour fast and shall
1 NSI-42
have accessories like door knob, Gravity/ auto return hinges,
privacy thumb turn with occupancy indicator, coat Hook, etc all
in SS 304. The hardware and fixings includes anchoring of all
fixed front panel to floor with SS 316 L brackets/ base plates
with a clearance height upto 110 mm, and covered with SS 316
Shoe box plates, wall and corner joineries (brackets and
channels) shall be SS 304 grade, SS 304 ss and weather silicone
sealant) provi

The cubicle unit shall be installed in approved finish, shades and

colours as per specifications and directions of Engineer-In-
Charge, including minimum 5 (five) years warranty against any
moisture related damages to all intermediate panels, doors,
hardqwares etc. Standard dimension of the cubicle system shall
be of approx. 2100 mm Height(overall) x 1500mm Depth and
1000 mm Width which includes 600mm door size width.

I shaped Cubicle System consisting of front face panel including

a) NSI door and all necessary accessories, fittings and hardware etc. Each 5.00 33222.60 166113.00

L shaped Cubicle System consisting of front face panel including

b) NSI door, intermediate panel and all necessary accessories, fittings Each 15.00 48740.15 731102.25
and hardware etc.
Manual Roller Blinds
Providing & fixing of Blackout Roller Blinds fabric made up of
100% Polyester with Acrylic coated of 0.32mm(PVC free) of
thickness 0.50mm ±5% and weighing 270-295gsm with
openness factor of 0% .Shrinkage % Warp<0.5 & Weft
<0.5,Color fastness>5-6. The control clutch drive unit engineered
heavy duty chain drive pulley operating system consisting of gear
clutch housing and locking plug containing minimum 6 ribs and
inserted at minimum of 37mm into roller tube. It is self-
lubricating Exclusive clutch with safety pins for secure bracket
installation and unlocking pin for quick manual removal.
Universal clutch is most convenient for large windows down to
2 NSI-43 the smallest windows. It shall be driven by a ball chain pulley Sqm 99.00 2215.70 219354.30
with ball chain and can be positioned at Right hand or Left hand
side of the shade. Clutch gear ration 1.75:1 for reduced
operating force on larger blinds. Tube bearing plug idler
Exclusive self-lubricating spring loaded plastic bearing end plug
with positive locking wheel allows for adjustment and provides
for a secure installation and removal of shade. Tube bearing plug
contain minimum 6 ribs and inserted a minimum of 37mm into
roller tube. Mounting hardware brackets universal brackets
including end plug bracket with lock down retainer device.
Brackets finish of powder coated metal installation brackets
made of stamped and hardened steel with 46mm projection for
wall, ceiling
Providing and
and sideGlass
fixing fittingReinforced
with screws and end(G.R.C)
Concrete cap covers.
Screen at
all levels & heights in approved size, pattern, design, thickness
and color. The Screens should be made from ‘53 grade’White
Portland Cement, Quartz, Fine Silica Sand, Alkali Resistant Glass
Fiber, Super Plasticizers, Polymers and U.V resistant Synthetic
3 NSI-44 inorganic pigments should be used for pigmentation. The Sqm 99.00 4788.80 474091.20
material casting should take place in Synthetic Rubber / FRP
Mould. The fixing of Jali should be ‘Dry fixing’ i.e. to be done with
MS/SS ‘L’ shaped Clamps, dash fasteners and pins etc as per site
requirment.

Automatic Sliding Doors

BOQ Civil Works Page 30 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Automatic sliding door operator - supply of automatic sliding

door Set 1 operator of DORMA (ES 200 easy ) as per approved
dwg. Compliant with european standards and produced
according to the guidelines for power-operated windows, doors
and gates, BGR 232, the UVV and the VDE regulations. TÜV
design tested, tested according to the low voltage guidelines,
fulfils DIN 18650 standards Standards for Pedestrian Safety, TUV
Design Tested for Durability of 1 Million Cycles. The track profile
should be separate from the main profile for enabling reduction
4 NSI-45 in vibration insulation. Operator length = 6250 mm, clear
passage opening width = 3000 mm, clear passage height = 2500
mm, includes micro processor controlled drive unit, with self
learning mechanism, program selector with knob, motion
detector (eagle 6 radars, 02 nos), mechanical components,
toothed belt, cover profile, floor guide for frameless glass (02
nos), glass clamping rail (02 nos), safety device-light barrier (01
pair).

Body finish : standard silver anodised operator profile,

electromechanical lock with 12 mm plain toughened frameless
glass for complete elevation - 2 moving panels. UPS of 750 VA
shall be provided by others, which will give power backup of 20
min. Only & if the duration of power cut to the operator is more
than 30 min.,then separate arrangement needs to be done for Each 1 304223 304223.40
the same as automatic operator requires uninterrupted
stabilized power supply. The above work complete in all respect
as per approved drawings and to the satisfaction of engineer-in-
charge / architect consultant.

Supply, installation testing and commissioning of vertical garden

consisting of welded MS Structure, poly propylene green wall
module with pots, Drip irrigation system and good-looking
outdoor plants to create a natural vertical garden look. The MS
structure for vertical garden of height 8.00 meter shall be
designed by the specialized agency to be enaged for the work of
vertical garden. MS structure to be finished with two or more
coat of epoxy paint of approved quality and shade over one coat
of primer. Poly propylene green wall module of size approx.
170mm x 470mm shall be mounted over MS Structure with the
support of fastener/screw /nut bolt etc as required. Each
module shall contain three poly propylene pots of size approx
125mm x 125mm. Drip Irrigation system consiting of LLDPE Drip
5 NSI-46 tubing 16 mm OD, 3.0 Kg/cm² rating, 2 LPH emitters at approx Sqm 25.00 25016.20 625405
150 mm spacing including all fittings and cpvc pipes of suitable
sizes for making connection with existing irrigation main line and
shall be capable to supply water to individual potted plants.
Plantation of different type of outdoor good looking plants to
create a natural vertical garden look with light weight. Each pot
shall contain soil mixture having cocopit, vermi compost, parlite,
vermilite & good earth, suitable for plantation. Vertical garden
shall be completed in all respect including temporary staging &
bracing and removal of the same after completion of vertical
garden and maintenance till the handing over to client, all
complete as per direction of Engineer-In-Charge.

Providing & fixing bacteria free polymide 6 grade nylon tube grab
bars of minimum diameter 32 mm x 3 mm thick reinforced with
full height anti corrosive aluminium core of approved make and
6 NSI-47 shade and conforming to ADA (Americans Disabilities Act) , all
complete as per specifications, drawing and direction of
Engineer- in-charge.

(a) (a) Grab Rail with Intermediate Wall Support Nos. 2.00 1309.65 2619.3
(b) (b) Vertical & Horizontal Safety Support Nos. 2.00 1101.65 2203.3
(c) (c) Basin Guard Rail Nos. 2.00 2080.05 4160.1

TOTAL (Carried Over to Summary of Civil Works) 0.00 2529271.85

P FURNITURE WORKS
1 President Office

BOQ Civil Works Page 31 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and Placing Cabin Table .Table Dimensions as

mentioned below. Main Table - 2400 mmL x 750mm W x750mm
Ht made of 25 mm thick Post Laminated Particle Board with
matching 2 mm thick edge Banding. Modesty panels are in
18mm thk Postlaminated finish. Table supports are combination
of Metal loop legs as shown in the image and Gable ends.
Access Flap with Cable tray and switch mounting plate is
provided on Main table for wire management. Main Table has a
3 drawer pedestal unit has castors and pedestal unit has size
400mm L x 450mm D x 680mm Ht made up of 18mm thk.
NSI-48 Prelaminated Particle Board Caracass having central locking Nos 1 131468 131468
system . 2 Drawers are with roller slide mechanism and Filing
Unit is with Ball bearing slides. The storage unit is made from
18mm prelaminated board. All the exposed edges are with 2mm
PVC egde Imported banding & sealed edges are with 0.8mm
thick PVC Imported edge banding. The top, side and hinged
shutters are sealed with 2mm thick PVC edge banding.Side
Storage of size 1200mm L x 450mm D x 680mm Ht is a com
bination of open shelves and hinged door unit and is made of
18mm thick pre laminated partical Board conforming to IS :
12823 and is hinged door unit. The back of the unit is made from
2 VP Office
Providing & Supplying Cabin Table with Main Table Dimension
2100mm L x 750 mm D . The Worktop is made of 25mm thick
Prelaminated particle board with 2 mm thick PVC Lipping on the
edges. The worktop is supported on Loop Shape Metal Legs
60mm x 30mm , powder coated understructure with Laminate
Modesty panel. The Metal legs are connected by Metal Beams
for stability and . The tables have metal inserts on underside for
modularity. Colour as per direction of Engineer in Charge. Side
return table of size 1200mm L x 450mm D x 750mm Ht with 3
Drawer pedestal unit Back Storage is of size 2100mm L x 450mm
NSI-49 D x 750mm Ht. Side and Back Storage are made of 18mm thick Nos 1 122988 122988
pre laminated partical Board conforming to IS : 12823. The back
of the unit is made from 18mm prelaminated board. All the
exposed edges are with 2mm PVC egde Imported banding &
sealed edges are with 0.8mm thick PVC Imported edge banding.
The top, side and hinged shutters are sealed with 2mm thick PVC
edge banding. The units are assembled by knock down fittings
such as Minifix & Dowels. All the hardware and Hinges are from
Ebco.

3 President chair/VP Chair

Providing and supplying High back chair with headrest in Mesh
Back with back tilt tension adjustable . The chair is mesh back &
seat fabric upholstered.The chair has Adjustable Lumber Support
and seat depth adjustment with synchronized Tilt . The Chair has
Nylon base with 60 mm twin wheel castors .Chair should have 1-
D adjustable armrests . Seat size is 490 mm W x 435 mm D and
NSI-50 the Chair Height 1135mm - 1225mm . Overall size of the chair is Nos 2 22965 45930
640mm W x 665mm D x (985 mm- 1220mm) H . The PU foam
used for chair seat is fire retardant .The chair has Pneumatic Gas
Lift with Stroke=85 mm and 5 star nylon base with soft/hard
castors . Chair carries a warranty of 5 years.

4 President chair/VP visitor Chair

Providing and supplying Mid back chair with headrest in Mesh
Back with back tilt tension adjustable . The chair is mesh back &
seat fabric upholstered.The chair has Adjustable Lumber Support
NSI-51 Nos 6 19699 118194
and seat depth adjustment with synchronized Tilt . The Chair has
Nylon base with 60 mm twin wheel castors .Chair should have 1-
D adjustable armrests . Seat size is 490 mm W x 435 mm D and
5 the
JointChair Height 1135mm -Cabin
Secretary/Secretary 1225mm
Table. Overall size of the chair is

BOQ Civil Works Page 32 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing & Supplying Cabin Table with Main Table Dimension

2100mm L x 750 mm D . The Worktop is made of 25mm thick
Prelaminated particle board with 2 mm thick PVC Lipping on the
edges. The worktop is supported on Loop Shape Metal Legs
50mm x 50mm , powder coated understructure with Laminate
Modesty panel. The Metal legs are connected by Metal Beams
for stability and . The tables have metal inserts on underside for
modularity. Colour as per direction of Engineer in Charge. Side
return table of size 1200mm L x 450mm D x 750mm Ht with 3
Drawer pedestal unit. Back Storage is of size 2100mm L x 450mm
NSI-52 D x 750mm Ht. Back Storage are made of 18mm thick pre Nos 3 72711 218133
laminated partical Board conforming to IS : 12823. The back of
the unit is made from 18mm prelaminated board. All the
exposed edges are with 2mm PVC egde Imported banding &
sealed edges are with 0.8mm thick PVC Imported edge banding.
The top, side and hinged shutters are sealed with 2mm thick PVC
edge banding. The units are assembled by knock down fittings
such as Minifix & Dowels. All the hardware and Hinges are from
Ebco.

6 Sofa - President/VP
Providing & Fixing of sofa . The inside frame is made of seasoned
wood and has antitermite treatment. The seat and back are
made of foam and is finished in fabric upholestry. The seat is
made of PU foam with density 35± 2 kg/cu.mtr. The back is
made of PU foam with density 35± 2 kg/cumtr upholstered.. The
NSI-53
Frame base has Webbing for Supporting the Cushions. The
Complete Sofa Body has Polyurethane Foam in desired shape.
The Sofa is supported on Metal Legs. Fabric colour and type as
per directions of Engineer in Charge.

i i 2 Seater 1200mmW X700mmDX720mm Nos 9 57201 514809

ii ii 1 Seater 900mm W X700mmDX720mm Nos 6 33101 198606
7 Sofa - Secretary/Joint Secretary
Providing & Fixing of sofa . The inside frame is made of seasoned
wood and has antitermite treatment. The seat and back are
made of foam and is finished in fabric upholestry. The seat is
made of PU foam with density 35± 2 kg/cu.mtr. The back is
made of PU foam with density 35± 2 kg/cumtr upholstered.. The
NSI-54
Frame base has Webbing for Supporting the Cushions. The
Complete Sofa Body has Polyurethane Foam in desired shape.
The Sofa is supported on Metal Legs. Fabric colour and type as
per directions of Engineer in Charge.

i i 2 Seater 1500mmW X700mmDX705mm Nos 2 63564 127128

8 President/VP Centre Table
Supplying of prelaminated top centre table TABLE TOP:Finish;
25mm thick LPL TopBASE:- Metal poweder coatedDIMENSIONS:
Width 1200mm, Depth 600mm and height 380-450
NSI-55 Nos 7 35238 246666
mm.WARRANTY: 5 years against any manufacturing
defects.DESIGN : as per the attached design intent

9 President/VP Side Table

Supplying of prelaminated top side table TABLE TOP:Finish;
25mm thick LPL TopBASE:- Metal poweder coatedDIMENSIONS:
Width 600mm, Depth 600mm and height 380-450
NSI-56 Nos 2 16256 32512
mm.WARRANTY: 5 years against any manufacturing
defects.DESIGN : as per the attached design intent

10 Secretary/Joint Secretary Centre Table

Supplying of prelaminated top centre table TABLE TOP:Finish;
25mm thick LPL TopBASE:- Metal poweder coatedDIMENSIONS:
Width 690 mm, Depth 690mm and height 380-450
NSI-57 Nos 1 29918 29918
mm.WARRANTY: 5 years against any manufacturing
defects.DESIGN : as per the attached design intent

11 Secretary/Joint Secretary Main chair

BOQ Civil Works Page 33 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and supplying High back chair with headrest in Mesh

Back with back tilt tension adjustable . The chair mesh and seat
fabric upholstered . The chair has Adjustable Lumber Support
and seat depth adjustment . The Chair has Nylon base with 60
mm twin wheel castors .Chair comes with 1-D adjustable
armrests . Seat size is 490 mm W x 435 mm D and the Chair
NSI-58 Nos 3 14878 44634
Height 975 mm - 1070 mm . Overall size of the chair is 630mm W
x 550 mm D x (975 mm- 1070mm) H . The PU foam used for chair
seat is fire retardant . The chair has Pneumatic Gas Lift with
Stroke=85 mm 5 star nylon base with soft/hard castors . Chair
carries a warranty of 5 years.

12 Secretary/Joint Secretary visitor chair

Providing and supplying Medium back chair in Mesh Back with
back tilt tension adjustable . The chair mesh and seat fabric
upholstered . The chair has Adjustable Lumber Support and seat
depth adjustment . The Chair has Nylon base with 60 mm twin
wheel castors .Chair comes with 1-D adjustable armrests . Seat
size is 490 mm W x 435 mm D and the Chair Height 975 mm -
NSI-59 Nos 6 12898 77388
1070 mm . Overall size of the chair is 630mm W x 550 mm D x
(975 mm- 1070mm) H . The PU foam used for chair seat is fire
retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm
5 star nylon base with soft/hard castors. Chair carries a warranty
of 5 years.

13 Staff Workstations
Providing and placing of workstations for Work pool area. The
size of the main working top would be:- 1400 (L) X 750 (D). The
workstations should be desk based workstations. The Side
Storage of each workstation should be 900mmL x 450mm D x
702 mm Ht and has a Seat on top at one end, the storage shall
be combo with open shelves and sliding/openable credenza. The
seat consists of seat cushion made of PU foam upholstered with
fabric. Glass/fabric Screen is provided between workstations for
Privacy having height of 450mm. The glass Screen is made of
Sandwitch Laquered Glass 8mm thick and is fixed to table top
with the help of Glass holding brackets which are in turn fixed to
the worktop. The worktop should be made of E1 grade 25 mm
thick pre laminated particle board with its edges finished with
NSI-60 2mm thick PVC edge band. The Legs are made of MS Steel in Nos 100 60234 6023400
50mm x 50mm Section with thickness of 1.6mm. The cross
members are made from 40x20x1.2 thk M.S. tubes. They are
powder coated with Epoxy Polyester. The Privacy Screens are .
Made of 18mm thick Particle Board and has Bottom , Top and
Side Panels. They are made up of 18 mm thick Pre- Laminated
Board. All the edges are provided with machine pressed 2 mm
thick PVC edge band. Wire management system in League Plus is
with Cable Trays running under the worktop to carry Data and
Electrical wires and Switches and Sockets are to be fixed by
customer on slots provided in Cable Trays. Cable Raisers are
installed at junction points only where cables are entering the
system from Floor into the cable Tray. All metal parts are duly
powder coated. The System should carry 5 Year Warranty from
Manufacturer.
14 Staff Workstation Chairs
Providing and fixing Medium Back Mesh Chair with Lumber
Support, Seat Size 510mm W x 510mm D, Back Size 480m W x
520mm Ht . The chair comes with PP arms , Nylon base with
50mm castors . The chair has Push Back Mechanism .The chair
NSI-61 comes with Pneumatic Gas Lift of Stroke=95 mm . Seat Height Nos 100 10798 1079800
Minimum 480mm from Ground and Maximum 570mm. Overall
size of the chair is 620 mm W x 680 mm D x (950 mm- 1050mm)
H .The Chair Warranty : 3 Years.

15 Meeting Table - 8 Pax

Providing & Fixing table of size 3000x1500. The Worktop shall be
made of 25mm Prelamparticle Board of Grade II , Type-II as per
IS:12823 and backing laminate of 0.6mm All the exposed edges
are finished with 2mm thick PVC lipping machine pressed. Legs
are made of powdered coated steel 50mmx 50mm Section.
NSI-62 Nos 2 150864 301728
Cross Member are in CRCA steel and the Beam is made of MSof
1.5mm thickness in powder coated finish of 50 microns thickness
. The above furniture should be as per specification and sample
approved by client.

16 Meeting Room Chairs

BOQ Civil Works Page 34 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and fixing Medium Back Mesh Chair with Lumber

Support, Seat Size 510mm W x 510mm D, Back Size 480m W x
520mm Ht . The chair comes with PP arms , Nylon base with
50mm castors . The chair has Push Back Mechanism .The chair
NSI-63 comes with Pneumatic Gas Lift of Stroke=95 mm . Seat Height Nos 28 10798 302344
Minimum 480mm from Ground and Maximum 570mm. Overall
size of the chair is 620 mm W x 680 mm D x (950 mm- 1050mm)
H .The Chair Warranty : 3 Years.

17 Board Room table

Providing & Fixing of Confetrence table of size 18000X2400mm.
the Worktop shall be made of 25mm Prelamparticle Board of
Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm
All the exposed edges are finished with 2mm thick PVC lipping
machine pressed. Legs are made of Aluminum Extrusion of
1.6mm thickness with aesthically designed elliptical Cover
sections . Legs are designed to facilitate wire management .
NSI-64 Cross Member are in CRCA steel and the Beam is made of MS Nos 1 480456 480456
and has size 75x50 mm of 1.5mm thickness in powder coated
finish of 50 microns thickness and is connected with legs to allow
for traversing of wires horizontally. The beam raceway provided
with slots for fixing data and electrical switches and sockets for
each user under the table.

18 Board Room Chair Main chair

Providing and supplying High back chair with headrest in Mesh
Back with back tilt tension adjustable . The chair is mesh back &
seat fabric upholstered.The chair has Adjustable Lumber Support
and seat depth adjustment with synchronized Tilt . The Chair has
Nylon base with 60 mm twin wheel castors .Chair should have 1-
D adjustable armrests . Seat size is 490 mm W x 435 mm D and
NSI-65 the Chair Height 1135mm - 1225mm . Overall size of the chair is Nos 1 22965 22965
640mm W x 665mm D x (985 mm- 1220mm) H . The PU foam
used for chair seat is fire retardant .The chair has Pneumatic Gas
Lift with Stroke=85 mm and 5 star nylon base with soft/hard
castors . Chair carries a warranty of 5 years.

19 Board Room Chair

Providing and supplying Medium Back Chair .This is a Medium
back chair with Mesh Back with back tilt tension adjustable . The
chair has Anchored Lumber Support . The Chair has Nylon base
with 50 mm twin wheel castors .Chair comes with 1-D adjustable
PP armrests . Seat size is 485 mm W x 470 mm D and the
NSI-66 Chair Height 945 mm - 1065 mm . Overall size of the chair is Nos 150 13063 1959450
600mm W x 560 mm D x (945 mm- 1065mm) H . The PU foam
used for chair seat is fire retardant . The chair has Pneumatic
Gas Lift with Stroke=85 mm . Chair carries a warranty of 3 years.

20 Waiting Area Sofa

The seat is made up of PU foam in density 35+/-2KG/cu meter ,
upholstered with fabric or leaterette. The back is made up of PU
foam in density 35+/-2KG/cu meter upholstered
leatherette/fabric.Understructure is made up of 1.2+/- cm thick
hot presses plywood moisture resistant and termite proof as per
NSI-67 IS:303 and pinewood of cross sections devoid of major knots and
surfacte defects. 6Nos per seat and 3.8mm dia zig zag spring
assembly is mounted over understructure for cushioning
purpose. Leg assembly is made out of powder coated metal.

i i 2 seater - 1500mmW X700mmDX720mm Nos 7 44617 312319

ii ii 1 seater - 835mm W X700mmDX720mm Nos 5 35240 176200
21 Compactors - 3 Bay

BOQ Civil Works Page 35 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing & Supplying Compactor of approximately 2050mm

height (Ht).The overall height of the standard module is 2050
mm from the bottom of the under carriage to the top of the
module. These modules are fabricated in the factory with knock
down construction covered from all the sides. The sheet used is
CRCA conforming to IS:513 Grade D with thickness 0.8-1mm for
the vertical back, side walls, top cover and horizontal shelves of
bodies. Bodies are fixed/movable are bolted to undercarriage
made up of 2-3mm thk HR Steel sheet which rolls onto
channels/rail of 1.2-2mm thk HR steel & 25mm square bright bar
which are embedded to the levelled ground. The Body has 3
NSI-68 Shelves. The sides/shelves shall be made from steel sheets
conforming to relevant codes. The construction of the units shall
be such that protection against dust by suitable overlapping of
sheets and adequate pressing of joint. The allowable
dimensional tolerance for the overall size of the body is 2mm.
The bodies should be complete knock down type and UDL each
shelf should be 40kg . No welding/metal working is allowed on
site, Bodies are fixed/movable are bolted to undercarriage is
allowed on site.

i i 2 Bay - 1980mm Ht x 2749mm W x 1842mm D Nos 6 223686 1342116

ii ii 2 Bay - 1980mm Ht x 1842mm W x 1838mm D Nos R/O 174270
22 Reception Centre Table
Supplying of prelaminated top centre table TABLE TOP:Finish;
25mm thick LPL TopBASE:- Metal poweder coatedDIMENSIONS:
Width 690 mm, Depth 690mm and height 380-450
NSI-69 Nos 7 29918 209426
mm.WARRANTY: 5 years against any manufacturing
defects.DESIGN : as per the attached design intent.

23 King size Bed

Providing & Supplying king sized bed of size D1800 x L2000-
2200mm x H800-900mmmm with the structure made out of
NSI-70 18mm ply and 1mm laminate The headboard is made up of Nos 8 59703 477624
18mm ply and 1mm laminate. Suitable for 78 x 72 inches king
size mattress
24 Bed Side Table
Providing & Supplying bedside table of size D450 x L450 x
H450mm with the structure made out of 18mm ply and a 1mm
NSI-71 Nos 16 19533 312528
laminate The table shall be 2 drawer with metal pullouts.

25 TV Console
Providing & Fixing rectangular table of Size
L1200xD450mmxH680. The Worktop shall be made of 25mm BSL
top , laminate of 0.6mm All the exposed edges are finished with
2mm thick PVC lipping machine pressed. Legs are made of
NSI-72 Nos 1 44384 44384
25mm thick BSL top with extra table in between below the main
table top . The above furniture should be as per specification and
sample approved by client.

26 Single size Bed - Caretaker

Providing & Supplying single sized bed of size D900 -1100x L2000-
2200mm x H800-900mm with the structure made out of 18mm
NSI-73 ply and 1mmlaminate/MDF including The headboard is made up Nos 1 53044 53044
of 18mm thick plywood and 1 mm laminate,

27 Living Room Sofa - 3 seater

Providing & Supplying sofa with the seat is made up of PU foam
in density 35+/-2KG/cu meter , upholstered with fabric or
leaterette. The back is made up of PU foam in density 35+/-
2KG/cu meter upholstered leatherette/fabric. Understructure is
made up of 1.2+/- cm thick hot presses plywood moisture
NSI-74 Nos 1 72088 72088
resistant and termite proof and pinewood of cross sections
devoid of major knots and surfacte defects. Leg assembly is
made out of solid wood. Dimensions W1800-2100 x D700- 800 x
H680-800mm.

28 Living room Centre Table

Providing & Supplying centre table of size D600 x L900 x
H450mm with the structure made out of 18mm solid wood with
NSI-75 Nos 1 31471 31471
ply and laminate. The table shall have glass top with additional
intermediate ply with laminate.
29 Café Table -

BOQ Civil Works Page 36 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing & Fixing round table of Size dia 1500mm, Height

737mm. The Worktop shall be made of 25mm Prelamparticle
Board of Grade II , Type-II as per IS:12823 and backing laminate
of 0.6mm All the exposed edges are finished with 2mm thick PVC
NSI-76 lipping machine pressed. Legs are made of powdered coated Nos 10 19767 197670
steel with pedestal round base with wire managment and access
flap on table top. The above furniture should be as per
specification and sample approved by client.

30 Café Chairs
Stackable chair without arms made up of Pre colored PP+GF20%
( 20% short glass fibre reinforced polypropylene) using injection
NSI-77 moldeing.Understructure is metal powder coated. The chair Nos 50 6900 345000
should be stackable upto 6 nos.

31 Storage
Supplying Hinged Door Free standing cabinet units having top,
sides, back, & shelves & door in 18mm thick pre laminated
partical Board conforming to IS : 12823. The back of the unit is
made from 18mm prelaminated board. All the exposed edges
NSI-78 are with 2mm PVC egde Imported banding & sealed edges are Nos 12 17330 207960
with 0.8mm thick PVC Imported edge banding. The cabinet shall
be provided with Lever CAM Locks.The handles shall be PVC
Moulded and shall be flush fitted. Size 900x400x1200mm.

TOTAL (Carried Over to Summary of Civil Works) 0.00 15860347.00

Q CRECHE ROOM
1 NSI-79 3 WAY ROCKER,Product Code:-2010,HSN Code:-9503 each 1.00 2660 2660
2 NSI-80 COUPE CAR RED,Product Code:-2110,HSN Code:-9503 each 1.00 4953 4953
3 NSI-81 ELEPHANT SLIDE,Product Code:-1220,HSN Code:-9503 each 1.00 8714 8714
4 NSI-82 HUMPTY DUMPTY RED,Product Code:-2070,HSN Code:-9503 each 1.00 1698 1698
5 NSI-83 PACER,Product Code:-2120,HSN Code:-9503 each 1.00 2742 2742
6 NSI-84 SEE SAW,Product Code:-2030,HSN Code:-9503 each 1.00 6880 6880
7 NSI-85 SPEEDO,Product Code:-2130,HSN Code:-9503 each 1.00 1606 1606
8 NSI-86 THE EASEL,Product Code:-4020,HSN Code:-9610 each 1.00 5962 5962

TOTAL (Carried Over to Summary of Civil Works) 0.00 35215.00

R MODULAR KITCHEN
Sub Head: Modular kitchen -Under storage cabinets
Providing & placing factory made modular kitchen cabinets
with openable shutters and sufficient number of drawers
made of 0.6mm body panels & 1.2mm thick horizontal
Frames of Galvanised sheet with zero spangels(as per
ASTM A653), components shall be powder coated with
high quality powders like Dupont, Kanasai Nerolac with
dry film thickness of 40 to 60 microns with pencil hardness
of 2H Min. It also includes the Tall unit of 2000 mm
height.All shelves shall be supported on approved quality S
S pins and shall be adjustable for different heights as per r
equirements.Shutters to be at least 18mm thick in
Galvanisheet steel .
Each shutter shall be fixed to the framework/carcass using
1 NSI-87 Sqm 19.2 24489 470188.8
two numbers of best quality CED coated hinges
( Blum, Hettich approved make) i/c soft/Auto closing
hinges as per requirement(Hettich make or equivalent)
fixed with SS screws , nails etc complete and these
shutters are provided with an approved quality of Godrej
Arc 128 mm pitch. Finished components shall be tested for
the critical quality parameters ,Adhesion and impact test
which enhances the life of kitchen.Shelves to be of
galvanised steel sheet with thickness of 12 mm with even
wire basket in grade 304 SS. Steel carcass and shutters
shall have passed the test like Static Load test,Shelf
deflection test.Modular kitchen accessories (Godrej or
equivalent make, payment for which will be made
Sub Head: Modular Kitchen : Wall units

BOQ Civil Works Page 37 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing & placing factory made modular kitchen cabinets

with openable shutters and having 0.6mm body panels &
1.2mm thick horizontal Frames of Galvanised sheet with
zero spangels(as per ASTM A653), components shall be
powder coated with high quality powders like Dupont,
Kanasai Nerolac with dry film thickness of 40 to 60
microns with pencil hardness of 2H Min.
All shelves shall be supported on approved quality SS pins
and shall be adjustable for different heights as per require
ments.Shutters to be at least 18mm thick in Galvanised
steel .Shutters will be of steel solid facia as well as Glass
shutters. The glass used in top unit shutters are used of
Saint Gobain or equivalent make. The glass used is itching
2 NSI-88 Sqm 16.52 19750 326270
in nature with 6mm thickness.
Each shutter shall be fixed to the framework/carcass using
two numbers of best quality CED coated hinges
( Blum, Hettich approved make) i/c soft/Auto closing
hinges as per requirement(Hettich make or equivalent)
fixed with SS screws , nails etc complete and these
shutters are provided with an approved quality of Godrej
Arc 128 mm pitch Handle . Finished components shall be
tested for the critical quality parameters ,Adhesion and
impact test which enhances the life of kitchen.Shelves to
be of galvanised steel sheet with thickness of 12 mm .
Steel carcase and shutters shall have passed the test like
Static Load test,Shelf deflection
Sub Head- Kitchen Accessories,
Providing and fixing Utensil Kit of Godrej Make of size
600mm in 304 SS grade i/c a set of soft closing baskets 2
Plain SS wire baskets 150 mm with required SS screw for
3 NSI-89 fixing above component of godrej make or quivalent, Each 8 18119 144952
complete as per drawing in the exisitng space, sample
prepared in sample flat at site and direction of Engineer-in-
charge.

TOTAL (Carried Over to Summary of Civil Works) 0.00 941410.80

S SIGNAGE WORKS
Providing & fixing at all heights and locations Letters made
up of Stainless steel, grade 316 of approved make made
out of laser cut shape in required design, language & font,
1 including buffing, polishing and fixing by sufficient
NSI-90
numbers of fasteners/ high quality chemical tape/
adhesive/fast of approved make, all complete as per
architectural drawings and direction of Engineer in charge.

Solid letters made of SS sheet of 5 mm thickness

Per letter
i i per cm 750.00 142.00 106500.00
height
2 NSI-91 Hollow letters made of SS sheet of 1.5 mm thickness 0.00
letters with depth of 25 mm
Per letter
i i per cm 950.00 68.00 64600.00
height
letters with depth of 50 mm
Per letter
ii ii per cm 750.00 91.00 68250.00
height
letters with depth of 75 mm
Per letter
iii iii per cm 950.00 108.00 102600.00
height

BOQ Civil Works Page 38 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing & fixing pictograms in 304 grade 2 mm thick

brush finished Stainless steel at all levels and locations
prepared using silk printing technology/ etching, filling
with industrial paint in required colours and baking to the
required condition at required temperature for obtaining
3 NSI-92 desired shine and gloss, in required font, design, pattern Sqcm 4500.00 7.00 31500.00
and size including buffing, polishing etc. and fixing by high
quality chemical tape/ adhesive of approved make on
prepared surface or with SS screw, all complete as per
architectural drawings and direction of Engineer in charge.

Providing & fixing at all levels and locations, informatory/

directional/warning signages in required font, design,
pattern and size made of 4 mm thick odorless Acrylic
sheets of make Cast/ Acrylite/ or approved equivalent,
conforming to specific gravity of 1.19, tensile strength of
69 MPA, percentage elongation of 4.2 %, modulus of
elasticity 2800 MPA (ASTM –D638), refractive index of 149,
(ASTM-D542) Rockwell hardness of M94 (ASTM – D785),
water absorption of 0.2 % (ASTM- D570) total light
transmission of 92 % (ASTM – D 1003) chemical, UV &
weather resistant, having excellent insulation properties,
abrasions resistant of approved color, of approved quality
4 NSI-93 and make, with beveled edges having self adhesive self Sqcm 7500.00 6.00 45000.00
luminescent vinyl sheet ( film thickness >150 micron,
luminescent duration 4-6 hours) of make 3M/ Avery or
approved equivalent over which the signage/ letter cutout
made of vinyl sheet ( film thickness > 80 micron) of make
3M/ Avery or approved equivalent is pasted in required
colour, font, design, al quality parameters ,Adhesion and
impact test which enhances the life of kitchen.Shelves to
be of galvanised steel sheet with thickness of 12 mm with
even wire basket in grade 304 SS. Steel carcass and
shutters shall have passed the test like Static L

Providing & fixing at all levels and locations, informatory/

directional/warning signages in required font, design,
pattern and size made of 4 mm thick odorless Acrylic
sheets of make Cast/ Acrilite or approved equivalent,
conforming to specific gravity of 1.19, tensile strength of
69 MPA, percentage elongation of 4.2 %, modulus of
elasticity 2800 MPA (ASTM –D638), refractive index of 149,
(ASTM-D542) Rockwell hardness of M94 (ASTM – D785),
water absorption of 0.2 % (ASTM- D570) total light
transmission of 92 % (ASTM – D 1003) chemical, UV &
weather resistant, having excellent insulation properties,
abrasions resistant of approved colour, with beveled edges
5 NSI-94 having self adhesive self luminescent vinyl sheet ( film Sqcm 3500.00 7.00 24500.00
thickness >150 micron, luminescent duration 4-6 hours) of
make 3M/ Avery or approved equivalent on both the faces
of the acrylic sheet, pasted with signage/ letter cutout
made of vinyl sheet ( film thickness >80 micron)of make
3M/ Avery or approved equivalent in required color, font,
design, patters are provided with an approved quality
of Godrej Arc 128 mm pitch Handle . Finished
components shall be tested for the critical quality
parameters ,Adhesion and impact test which enhances the
life of kitchen.Shelves to be of galvanised steel sheet with
thi

BOQ Civil Works Page 39 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing & fixing at all levels and locations, informatory/

directional/warning signages in required font, design,
pattern, size, sandwiched between two acrylic sheets with
beveled edges of make Cast/ Acrilite or approved
equivalent, each of minimum 4 mm thick, bottom sheet of
required colour+B139 and top sheet shall be clear and
transparent, acrylic sheet conforming to specific gravity of
1.19, tensile strength of 69 MPA, percentage elongation of
4.2 %, modulus of elasticity 2800 MPA (ASTM –D638),
odorless, refractive index of 149, (ASTM-D542) Rockwell
hardness of M94 (ASTM – D785), water absorption of 0.2
% (ASTM- D570) total light transmission of 92 % (ASTM – D
6 NSI-95 1003) chemical, UV & weather resistant, having excellent Sqm 4500.00 13.00 58500.00
insulation properties, abrasions resistant of approved
colour, , The signage shall be made by pasting the base
plate with self adhesive self luminescent vinyl sheet ( film
thickness >150 micron, luminescent duration 4-6 hours) of
make 3M/ Avery or approved equivalent, pasted with
signage/ rs are provided with an approved quality
of Godrej Arc 128 mm pitch Handle . Finished
components shall be tested for the critical quality
parameters ,Adhesion and impact test which enhances the
life of kitchen.Shelves to be of galvanised steel sheet with
thickness of 12 mm . Steel carcase and shutters shall have
passed the test like Static Load test,Shelf deflecti
Providing & fixing at all heights and locations back lit
hollow Letters/ Brand Logo/Emblem made up of Stainless
steel, grade 316 (1mm thick returns/ side face and 1.5 mm
thick front face) of approved make made out of laser cut
shape in required design, language & font, with
handcrafted returns(sides) including PU coating (MRF or
approved equivalent) of desired color as per brand
guidelines, having the coat of matt/glossy MRF HS Clear or
approved equivalent on outer surface, fixed with
matching color PU Painted SS screws and heavy duty
double sided tape of make 3M/AVERY or approved
equivalent, to a backing letter of same design, language,
7 NSI-96 font and size and made up of 3mm thick acrylic sheet of 0.00
make ACAST/ACRYLITE or approved equivalent for uniform
color distribution in the back/ side, having 66 IP LED light
modules of GE/ CREE/ NICHIA/ OSRAM or approved
equivalent of approved color fixed with heavy duty tape of
make 3M/AVERY or approved equivalent inside the hollow
letters in required numbers for desired level of
illumination with appropriate control gears in required
numbers and of same make as that of LED, FRLS rated
wiring of FINOLEX/POLYCAB or approved equivalent , IP 66
control gear box of RITTAL or approved equivalent of
suitable size for installation of gears controls, including
installation on wall using chemical anchor fasteners of
HILTI/FISHER
Letters or approved equivalent all complete as per
Per letter
i i per cm 350.00 311.00 108850.00
height
ii ii Brand Logo/Emblem Sqcm 1700.00 136.00 231200.00

BOQ Civil Works Page 40 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Sl. No. DSR-2018 DESCRIPTION UNIT Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Providing and Fixing modular curve type name plate

signage consisting a fixed aluminium base and an
insertable/removable name pate. Aluminium base shall be
made of powder coated aluminium extruded section (min.
1.7 mm thick) to form slotted arrangment with groove at
top & bottom and acrylic end cap fixed with screw on both
sides. Name plate shall be made of 0.6-0.8 mm thick
polycarbonate sheet (a vinyl printed sheet will pasted over
this sheet saperately) and a transparent 0.6-0.8 mm thick
8 NSI-97 polycarbonate protecting film. Aluminium base to be fixed Sqcm 8500.00 3.00 25500.00
by SS screw on wall or by high quality chemical
tape/adhesive of approved make on prepared surface,
name plate to be inserted in aluminium base at all levels
and locations as per architectural drawings and direction
of Engineer in charge.
(Note- Printed vinyl sheet shall be paid saperately.
Polycarbonate sheet and polycarbonate protection film is
included in this item.).
Extra for providing & fixing vinyl print sheet for modular
name plate signage including printing vinyl sheet as per
9 NSI-98 drawings, pasting vinyl sheet over existing polycarbonate Sqcm 9500.00 7.00 66500.00
sheet and fixing in modular curve type name plate signage.

TOTAL (Carried Over to Summary of Civil Works) 0.00 933500.00

GRAND TOTAL 121531453.83 43714891.29

Total of DSR & NDSR 165246345.12

BOQ Civil Works Page 41 of 41

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

PROJECT :- CONSTRUCTION OF OFFICE BUILDING FOR DENTAL COUNCIL OF INDIA AT RK PURAM, NEW DELHI
GUARD ROOM & GATE , BOQ - CIVIL WORKS

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic
excavator) / manual means in foundation trenches or drains (not
exceeding 1.5 m in width or 10 sqm on plan), including dressing
1 2.8 of sides and ramming of bottoms, lift upto 1.5 m, including
getting out the excavated soil and disposal of surplus excavated
soil as directed, within a lead of 50m.

i 2.8.1 All kinds of soil. Cum. 27.74 252.30 6999.81

Extra for every additional lift of 1.5 m or part thereof in.
2 2.26

i 2.26.1 All kinds of soils Cum 1.73 90.40 156.75

Excavating trenches of required width for pipes, cables, etc.
including excavation for sockets, and dressing of sides, ramming
3 2.10 of bottoms, depth upto 1.5m including getting out the excavated
soil, and then returning the soil as required, in layers not exc

a 2.10.1 All kinds of soil.

Pipes, cables, etc. exceeding 80mm dia but not exceeding
i 2.10.1.2 300mm dia. rmt 15.00 364.20 5463.00

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in
4 2.25 depth, consolidating each deposited layer by ramming and Cum. 23.92 219.65 5253.85
watering, lead up to 50 m and lift upto 1.5 m.

Carriage of Earth by mechanical transport including loading,

5 1.1.2 unloading and Stacking including royalty & carriage up to 5 KM Cum. 3.82 201.83 771.96
complete.

Supplying and filling in plinth with river sand under floors

6 2.27 including, watering, ramming consolidating and dressing Cum. 0.30 1953.05 591.41
complete.
Supplying chemical emulsion in sealed containers including
7 2.34 delivery as specified

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

i 2.34.1 litre 1.00 200.85 200.85

8 Anti termite treatment

Diluting and injecting chemical emulsion for POST-
2.35 CONSTRUCTIONAL anti-termite treatment (excluding the cost of
chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion

@ one litre per hole, 300 mm apart including drilling 12 mm
a) 2.35.3 diameter holes and plugging with cement mortar 1 :2 (1 cement
: 2 Coarse sand) to match the existing floor :

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

i 2.35.3.1 Sqm 3.03 227.05 687.54

TOTAL (Carried Over to Summary of Civil Works) 20125.18 0.00

B 4.0 CONCRETE WORKS

Providing and laying in position cement concrete of specified
1 4.1 grade excluding the cost of centering and shuttering - All work
up to plinth level :

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40

a 4.1.8 mm nominal size) Cum. 1.73 5789.60 10041.00

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone

b 4.1.3 aggregate 20 mm nominal size) CUM 0.14 6788.60 927.46

Providing and laying damp-proof course 50 mm thick with

2 4.11 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded Sqm 2.06 418.90 863.75
stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing material in cement

3 4.12 concrete work in doses by weight of cement as per per 50 kg 0.66 56.55 37.31
manufacturer’s specification. cement

BOQ for Guard Room Page 1 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

Applying a coat of residual petroleum bitumen of grade of VG-10

of approved quality using 1.7 kg per square metre on damp
4 4.13 proof course after cleaning the surface with brushes and finally Sqm 2.06 110.00 226.81
with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6

(1 cement :3 coarse sand : 6graded stone aggregate 20mm
nominal size) over 75mm bed by dry brick ballast 40mm nominal
5 4.17 size well rammed and consolidated and grouted with fine sand Sqm 2.31 614.05 1418.46
including finishing the top smooth

TOTAL (Carried Over to Summary of Civil Works) 13514.80 0.00

C 5.0 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. and
1 5.9 removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

a 5.9.1 Sqm 14.75 284.85 4200.97

Walls (any thickness) including attached pilasters, butteresses,

b 5.9.2 plinth and string courses etc. Sqm 0.00 609.30 0.00

Suspended floors, roofs, landings, balconies and access platform.

c 5.9.3 Sqm 8.81 693.05 6103.88

d 5.9.4 Shelves (Cast in situ) Sqm 0.72 693.05 499.00

Lintels, beams, plinth beams, girders, bressumers and cantilevers
e 5.9.5 Sqm 14.89 552.05 8220.99

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 16.97 733.70 12453.82
Small lintels not exceeding 1.5m clear span, moulding as in
cornices, window sills, string courses, bands, copings, bed plates,
g 5.9.15 Sqm 1.25 284.85 354.64
anchor blocks and the like.

h 5.9.16 Edges of slabs and breaks in floors and walls

5.9.16.1 Under 20 cm wide metre 12.92 173.25 2238.39
Reinforcement for R.C.C. work including straightening, cutting,
2 5.22 bending, placing in position and binding all complete upto plinth
& above plinth level.
i 5.22.6 Thermo-Mechanically Treated bars. kg 971.43 83.50 81114.60
Providing and laying in position machine batched and machine
mixed design mix M-25 grade cement concrete for reinforced
cement concrete work, using cement content as per approved
design mix, including pumping of concrete to site of laying but
excluding the cost of centering, shuttering, finishing and
3 5.33 reinforcement, including admixtures in recommended
proportions as per IS: 9103 to accelerate, retard setting of
concrete, improve workability without impairing strength and
durability as per direction of Engineer-in-charge.

(Note :- Cement content considered in this item is @ 330

kg/Cum. Excess/less cement used as per design mix is
payable/recoverable separately).
i 5.33.1 All works upto plinth level. Cum 3.66 7997.30 29261.70
ii 5.33.2 All works above plinth level upto floor V level. Cum 2.86 9400.85 26911.73

TOTAL (Carried Over to Summary of Civil Works) 171359.72 0.00

D 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks
1 6.1 of class designation 7.5 in foundation and plinth in:

i 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 0.62 6376.25 3944.25
Brick work with common burnt clay F.P.S. (non modular) bricks
2 6.4 of class designation 7.5 in superstructure above plinth level up to
floor V level in all shapes and sizes in :
i 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 2.46 7590.45 18649.15

BOQ for Guard Room Page 2 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

Half brick masonry with F.P.S. bricks of class designation 75 in

3 6.13 superstructure above plinth level up to floor V level.

i 6.13.2 cement mortar 1:4 (1 cement : 4 coarse sand) Sqm. 10.23 932.10 9537.71
Extra for providing and placing in position 2 Nos. 6mm dia. M.S.
4 6.15 bars at every third course of half brick masonry (with F.P.S. Sqm 10.23 80.10 819.62
bricks).

TOTAL (Carried Over to Summary of Civil Works) 32950.74 0.00

E 8.0 MARBLE & GRANITE WORK

Providing and fixing 18mm thick gang saw cut ( premoulded and
prepolished) machine cut for kitchen platforms, vanity counters,
window sills , facias and similar locations of required size of
approved shade, colour and texture laid over 20mm thick base
cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated
1 8.2 with white cement, mixed with matching pigment, epoxy touch
ups, including rubbing, curing, moulding and polishing to edge to
give high gloss finish etc. complete at all levels.

a) 8.2.2 Granite of any colour and shade

i 8.2.2.1 Area of slab upto 0.50 Sqm.( For Counter) Sqm. 0.72 4217.35 3036.49
Extra for fixing marble / granite stone over and above
corresponding basic item, in facia and drops of width upto
2 8.4 150mm with epoxy resin baesd adhesive including cleaning etc. metre 1.20 434.25 521.10
complete.

TOTAL (Carried Over to Summary of Civil Works) 3557.59 0.00

F 9.0 WOOD & PVC WORK

Providing and fixing ISI marked flush door shutters conforming to
IS : 2202 (Part I) non-decorative type, core of block board
construction with frame of 1st class hard wood and well
1 9.21 matched commercial 3 ply veneering with vertical grains or cross
bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

i 9.21.1 necessary screws sqm 3.15 1,886.70 5943.11

Extra for providing lipping with 2nd class teak wood battens 25
mm minimum depth on all edges of flush door shutters (over all
2 9.23 area of door shutter to be measured). Sqm 3.15 401.40 1264.41

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including
3 9.48 priming coat with approved steel primer all complete.

i 9.48.1 Fixed to steel windows by welding kg 25.20 165.30 4165.56

Providing and fixing IS : 3564 marked Aluminium die cast body
4 9.83 tubular type universal hydraulic door closer with necessary each 0 1003.50 0.00
accessories and screws etc. complete.
Providing and fixing aluminium tower bolts ISI marked anodised
(anodic coating not less than grade AC 10 as per IS : 1868 )
5 9.97 transparent or dyed to required colour or shade with necessary
screws etc. complete :

i 9.97.1 300x10 mm each 4.00 116.80 467.20

ii 9.97.5 100x10 mm each 2.00 58.15 116.30
Providing and fixing aluminium pull bolt lock, ISI marked,
anodised (anodic coating not less than grade AC 10 as per IS :
6 9.98 1868) transparent or dyed to required colour and shade, with Each 2.00 85.95 171.90
necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles of approved make

anodized (anodic coating not less than grade AC 10 as per IS :
7 9.100 1868) transparent or dyed to required colour or shade with
necessry screws etc. complete.
i 9.100.1 125 mm Each 4.00 59.65 238.60

BOQ for Guard Room Page 3 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

ii 9.100.2 100mm each 2.00 52.85 105.70

Providing and fixing aluminium hanging floor door stopper ISI
marked anodised (anodic coating not less than grade AC 10 as
8 9.101 per IS : 1868) transparent or dyed to required colour and shade
with necessary screws etc. complete.

i 9.101.1 Single rubber stopper each 0.00 33.95 0.00

Providing and fixing bright finished 100 mm mortice lock with 6
levers without pair of handles of approved quality for aluminium
9 9.113 door, with necessary screws etc complete as per direction of Each 0.00 637.05 0.00
Engineerin-charge.

Providing and fixing PVC rigid foam sheet 1 mm thick on existing

10 9.125 door shutters (bathroom and W.C. doors) using synthetic rubber sqm 3.15 1,200.35 3781.10
based adhesive.

TOTAL (Carried Over to Summary of Civil Works) 16253.88 0.00

G 10.0 STEEL WORK

Providing and fixing T-iron frames for doors, windows and
ventilators of mild steel Tee-sections, joints mitred and welded,
1 10.13 including fixing of necessary butt hinges and screws and applying
a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse
i 10.13.1 sand : 6 graded stone aggregate 20 mm nominal size) KG 54.45 106.45 5796.20

Steel work welded in built up sections/ framed work, including

cutting,hoisting, fixing in position and applying a priming coat of
2 10.25 approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates

i 10.25.2 and similar works KG 1533.12 131.00 200839.11

Supplying, installing, Testing and commissioning 2.7 to 3 m

high, heavy duty Motorized M.S. Sliding gate ( approx.
weight of gate wing 1300-1400 kg) for an opening of 6 m
width, of approved design as per drawing using laser cut
technology, with two or more coats of epoxy paint over
one coat of epoxy primer of approved make, with manual
operation feature, and comprising of Galvanized Wheels
with ball bearings and axle with lubrication point,
Galvanized adjustable upper guide brackets with guide
posts (2 Nos) with nylon rollers, End of the run galvanized
3 NSI limit stop with magnetic limit switch, M.S. Post with Safety Each 1.00 172806.00 172806.00
strike, Rail with C-channel & bottom bar, 230-240 V AC - 50
Hz Electromechanical actuator of approved make for
Sliding gate for opening/closing speed of 0.20 - 0.30 m/s
(adjustable if required), rack or chain driven Drive unit of
approved make and capacity ( Thrust> 1200N) comprising
of integral electronic control unit & in built contact-less
magnetic limit-switch with imported galvanized rack (duly
hardened and tempered) and key selector, Pair of
Photocells with anodized aluminium vertical mountings
and Flashing light, safety edge strip and other necessary

TOTAL (Carried Over to Summary of Civil Works) 206635.32 172806.00

BOQ for Guard Room Page 4 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

H 11.0 FLOORING WORK

Kota stone slab flooring over 20 mm (average) thick base laid
over and jointed with grey cement slurry mixed with pigment to
1 11.26 match the shade of the slab including rubbing and polishing
complete with base of cement mortar 1 : 4 (1 cement : 4 coarse
sand) :
i 11.26.1 25 mm thick. sqm 1.89 1531.85 2895.20
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and
pillars laid on 12 mm (average) thick cement mortar 1:3 (1
cement 3 coarse sand) and jointed with grey cement slurry
2 11.27 mixed with pigment to match the shade of the slabs, including sqm 0.50 1810.05 905.03
rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/

3 11.31 sand stone slab. rmt 3.60 148.10 533.16

Extra for Kota stone/ sand stone in treads of steps and risers
4 11.32 using single length up to 1.05 metre. sqm 1.89 33.10 62.56

Providing & Laying vitrified floor tiles in different sizes ( thickness

to be specified by the manufacturer) with water absorption's
less than 0.08% and confirming to IS : 15622 of approved make
in all colours and shades, laid on 20mm thick cement mortar 1:4
5 11.41 (1 cement : 4 coarse sand) including grouting the joints with
white cement and matching pigments etc, complete.

i 11.41.2 Size of Tile 600x600 mm sqm 2.25 1500.55 3370.61

Providing and laying Vitrified tiles in different sizes (thickness to
be specified by manufacturer), with water absorption less than
0.08 % and conforming to
I.S. 15622, of approved make, in all colours & shade, in skirting,
6 11.46 riser of steps, over 12 mm thick bed of cement mortar 1:3 (1
cement: 3 coarse sand), jointing
with grey cement slurry @ 3.3 kg/ sqm including grouting the
joint with white cement & matching pigments etc. complete.

i 11.46.2 Size of Tile 600x600 mm sqm 0.53 1545.85 811.57

Providing and fixing Ist quality ceramic glazed wall tiles
conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by
Engineerin-Charge, in skirting, risers of steps and dados, over 12
7 8.31 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) sqm 9.41 1030.30 9689.97
and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade
complete.

Providing and laying Ceramic glazed floor tiles of size 300x300

mm (thickness to be specified by the manufacturer), of 1st
quality conforming to IS : 15622, of approved make, in all
colours, shades, except White, Ivory, Grey, Fume Red Brown, laid
8 11.38 on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sqm 1.89 996.70 1880.03
sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including
pointing the joints with white cement and matching pigments
etc., complete.

TOTAL (Carried Over to Summary of Civil Works) 20148.12 0.00

I 12.0 ROOFING
Providing and laying gola 75x75mm in cement concrete M15
grade including finishing with cement mortar 1:3 (1 cement : 3
1 12.21 fine sand) as per standard design in 75x75 mm deep chase. rmt. 9.22 237.25 2188.39

BOQ for Guard Room Page 5 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

Making khurras 45x45 cm with average minimum thickness of 5

cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1
2 12.22 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 each 1.00 244.05 244.05
cement : 3 coarse sand) and a coat of neat cement, rounding the
edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain

water pipes conforming to IS : 13592 Type A, including jointing
3 12.41 with seal ring conforming to IS : 5382, leaving 10 mm gap for
thermal expansion,
(i) Single socketed pipes.

i 12.41.2 110 mm diameter rmt. 3.20 305.05 976.16

Providing and fixing on wall face unplasticised - PVC moulded
fittings/ accessories for unplasticised Rigid PVC rain water pipes
4 12.42 conforming to IS : 13592 Type A, including jointing with seal ring
conforming to IS : 5382, leaving 10 mm gap for thermal
expansion.

a) 12.42.1 Coupler
i 12.42.1.2 110 mm Each 1 117.80 117.80
b) 12.42.5 Bend 87.5°
i 12.42.5.2 110 mm bend Each 1 129.85 129.85
c) 12.42.6 Shoe (Plain)
i 12.42.6.2 110 mm Shoe Each 1 113.80 113.80

TOTAL (Carried Over to Summary of Civil Works) 3770.05 0.00

J 13.0 FINISHING WORK

1 13.4 12 mm cement plaster of mix :
i 13.4.2 1:6 (1 cement: 6 coarse sand) sqm 16.04 263.55 4226.02
15 mm cement plaster on rough side of single or half brick wall
2 13.5
of mix :
i 13.5.2 1:6 (1 cement: 6 coarse sand) sqm 36.51 303.90 11095.39
3 13.16 6 mm cement plaster of mix :
i 13.16.1 1:3 (1 cement: 3 fine sand) sqm 7.82 227.35 1778.96
per bag of
Extra for providing and mixing water proofing material in cement
50KG
4 13.21 plaster work in proportion recommended by the manufacturers. 6.86 59.75 409.88
Cement
Used in
Distempering with oil bound washable distemper of approved
5 13.41 brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat
i 13.41.1 with cement primer. sqm 23.86 153.45 3661.28

Finishing walls with Premium Acrylic Smooth exterior paint with

6 13.47
Silicone additives of required shade :
New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over
i 13.47.1 and including priming coat of exterior primer applied @ 2.20 kg/ sqm 36.51 161.15 5883.59
10 sqm)
Finishing walls with Deluxe Multi surface paint system for
7 13.48 interiors and exteriors using Primer as per manufacturers
specifications :
Painting wood work with Deluxe Multi Surface Paint of required
shade. Two or more coat applied @0.90 ltr/10 sqm over an
i 13.48.2 under coat of primer applied @0.75 ltr/ 10 sqm of approved sqm 6.30 130.25 820.58
brand or manufacture

8 13.50 Applying priming coat :

With ready mixed pink or Grey primer of approved brand and
i 13.50.1 manufacture on wood work (hard and soft wood) sqm 6.30 57.05 359.42

With ready mixed red oxide zinc chromate primer of approved

ii 13.50.3 brand and manufacture on steel galvanised iron/ steel works sqm 1.98 50.70 100.39

Painting with synthetic enamel paint of approved brand and

9 13.61 manufacture to give an even shade :

i 13.61.1 Two or more coats on new work sqm 15.79 121.55 1918.79

BOQ for Guard Room Page 6 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the
10 13.80 plastered wall surface to prepare the surface even and smooth Sqm 60.37 115.15 6951.58
complete
Add for plaster drip course/ groove in plastered surface or
11 5.30 meter 20.40 58.90 1201.56
moulding to R.C.C. projections.

TOTAL (Carried Over to Summary of Civil Works) 38407.42 0.00

K 21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS : 1285, fixed with
rawl plugs and screws or with fixing clips, or with expansion hold
fasteners including necessary filling up of gaps at junctions, at
top, bottom and sides with required PVC/neoprene felt etc.
Aluminium sections shall be smooth, rust free, straight, mitred
1 21.1 and jointed echanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P. brass /
stainless steel screws, all complete as per architectural drawings
and the directions of Engineer-in-charge. Glazing and paneling
to be paid for separately) :

a) 21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder
i 21.1.1.2 coating 50 micron) kg 30.36 456.30 13853.27

For shutters of doors, windows & ventilators including providing

and fixing hinges/ pivots and making provision for fixing of
fittings wherever required including the cost of EPDM rubber /
b) 21.1.2 neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder

i 21.1.2.2 coating 50 micron) kg 38.64 546.35 21110.96

Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber /
neoprene gasket etc. complete as per the architectural drawings
3 21.3 and the directions of engineer-in-charge . (Cost of aluminium
snap beading shall be paid in basic item):

i 21.3.1 With float glass panes of 4.0 mm thickness sqm 2.52 999.60 2518.99

Filling the gap in between aluminium frame and adjacent

RCC/Brickwork/ Stone Work by providing weather silicon sealant
5 21.8
over backer rod of approved quality as per architectural
drawings and direction of Engineer-in-charge

i 21.8.1 Upto 5mm depth and 5mm width metre 13.80 79.45 1096.41

TOTAL (Carried Over to Summary of Civil Works) 38579.63 0.00

L 22.0 WATER PROOFING

BOQ for Guard Room Page 7 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Guard Room, Boq.

DSR
Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR Amount NDSR RATE NDSR Amount
RATE

Providing & laying integral cement based water proofing

treatment including preparation of surface as required for
treatment of roofs, balconies, terraces etc consisting of following
operations: a) Applying a slurry coat of neat cement using
2.75kg/sqm of cement admixed with water proofing compound
confirming to IS. 2645 and approved by Engineer-in-charge over
the RCC slab including adjoining walls upto 300mm height
including cleaning the surface before treatment. b) Laying brick
bats with mortar using broken bricks/brick bats 25mm to
115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse
1 22.7
sand ) admixed with water proofing compound confirming to IS :
2645 and approved by Engineer-in-charge over 20 mm thick
layer of cement of 1:5 ( 1 cement : 5 coarse sand ) admixed with
water proofing compound confirming to IS : 2645 and approved
by Engineer-in-charge to required slope and treating similarly
the

adjoining walls upto 300mm height including rounding of

junctions of walls and slabs. c) After two days of proper curing
applying a second coat of cement slurry using 2.75kg/sqm of
cement admixed with water proofing compound confirming to IS
: 2645 and approved by Engineer-in-charge. d) Finishing the
surface with 20 mm thick jointless cement mortar 1:4 (1 cement
: 4 coarse sand ) admixed with water proofing compound
confirming to IS : 2645 and approved by Engineer-in-charge
including laying glass fibre cloth of approved quality in top layer
and finally finishing the surface with trowel with neat cement
slurry and making pattern of 300x300 mm square 3mm deep. e)
The whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test. All
above operations to be done in order and as directed and
specified by the Engineer-in-charge:

With average thickness of 120mm and minimum thickness at

i 22.7.1 khurra as 65mm. sqm 4.10 1398.50 5731.05

TOTAL (Carried Over to Summary of Civil Works) 5731.05 0.00

GRAND TOTAL 571033.49 172806.00

Total of DSR & NDSR 743839.49

BOQ for Guard Room Page 8 of 8

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi. Boq.

BOUNDARY WALL
BILL OF QUANTITY

S. No. DSR 2018 Description Unit Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means over areas
(exceeding 30cm in depth. 1.5m in width as well as 10
1 2.6 sqm on plan) including disposal of excavated earth,
lead upto 50m and lift upto 1.5m, disposed earth to be
levelled and neatly dressed.

i 2.6.1 All kinds of soils Cum 74.62 181.85 13569.65

Earth work in excavation by mechanical means
(Hydraulic excavator)/manual means over areas
(exceeding 30 cm in depth, 1.5 m in width as well as 10
2 2.7
sqm on plan) including getting out and disposal of
excavated earth lead upto 50 m and lift upto 1.5 m, as
directed by Engineer-in-charge.
i 2.7.1 Ordinary rock Cum 17.22 352.45 6069.19
Extra for every additional lift of 1.5 m or part thereof
3 2.26
in.
i 2.26.1 All kinds of soils Cum 5.74 90.40 518.90
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers not
2 2.25 exceeding 20cm in depth, consolidating each deposited Cum 35.57 219.65 7811.96
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
Carriage of Earth by mechanical transport including
3 1.1.2 loading, unloading and Stacking including royalty & Cum 17.22 201.83 3475.51
carriage up to 5 KM complete.

TOTAL (Carried Over to Summary of Civil Works) 31445.2 0.0

B 4.0 CONCRETE WORKS

Providing and laying in position cement concrete of
1 4.1 specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
1:4:8 (1 cement : 4 coarse sand : 8 graded stone
i 4.1.8 Cum 11.4 5789.60 66231.00
aggregate 40 mm nominal size)
Providing and laying damp-proof course 50mm thick
with cement concrete 1:2:4 (1 cement : 2 coarse sand :
2 4.11 SQM 30.49 418.90 12770.89
4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material

in cement concrete work in doses by weight of cement per 50 kg
3 4.12 9.76 56.55 551.69
as per manufacturer’s specification. cement

Applying a coat of residual petroleum bitumen of grade

of VG-10 of approved quality using 1.7 kg per square
4 4.13 metre on damp proof course after cleaning the surface SQM 30.49 110.00 3353.54
with brushes and finally with a piece of cloth lightly
soaked in kerosene oil.
Making plinth protection 50mm thick of cement
concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6
graded stone aggregate 20 mm nominal size) over
5 4.17 75mm thick bed of dry brick ballast 40 mm nominal SQM 614.05 0.00
size, well rammed and consolidated and grouted with
fine sand, including necessary excavation, levelling &
dressing & finishing the top smooth.

TOTAL (Carried Over to Summary of Civil Works) 82907.1 0.0

C 5.0 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping
1 5.9
etc. and removal of form for :
Foundations, footings, bases of columns, etc. for mass
a 5.9.1 Sqm. 25.84 284.85 7360.52
concrete.
Lintels, beams, plinth beams, girders, bressumers and
d 5.9.5 Sqm. 135.55 552.05 74830.93
cantilevers
Columns, Pillars, Piers, Abutments, Posts and Struts.
e 5.9.6 Sqm. 257.05 733.70 188597.59

Page 1 of 3
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi. Boq.

BOUNDARY WALL
BILL OF QUANTITY

S. No. DSR 2018 Description Unit Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

Reinforcement for R.C.C. work including straightening,

2 5.22 cutting, bending, placing in position and binding all
complete all level.
a 5.22.6 Thermo-Mechanically Treated bars. KG 7169.2 83.50 598632.16
Providing and laying in position machine batched and
machine mixed design mix M-25 grade cement
concrete for reinforced cement concrete work, using
cement content as per approved design mix, including
pumping of concrete to site of laying but excluding the
3 5.33 cost of centering, shuttering, finishing and
reinforcement, including admixtures in recommended
proportions as per IS: 9103 to accelerate, retard setting
of concrete, improve workability without impairing
strength and durability as per direction of Engineer-in-
charge.
(Note :- Cement content considered in this item is @
330 kg/Cum. Excess/less cement used as per design mix
is payable/recoverable separately).
i 5.33.1 All works upto plinth level. Cum 45.51 7997.30 363950.66
ii 5.33.2 All works above plinth level upto floor V level. Cum 17.76 9400.85 166959.09

TOTAL (Carried Over to Summary of Civil Works) 1400330.95 0.00

D 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non
1 6.1 modular) bricks of class designation 7.5 in foundation
and plinth in:
i 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 42.68 6376.25 272147.42
Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
2 6.4
superstructure above plinth level up to floor V level in
all shapes and sizes in :
i 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 79.27 7590.45 601660.80

TOTAL (Carried Over to Summary of Civil Works) 873808.2 0.0

E 10.0 STEEL WORK

Steel work welded in built up sections/ framed work,
including cutting, hoisting, fixing in position and
1 10.25 applying a priming coat of approved steel primer using
structural steel etc. as required.
In gratings, frames, guard bar, ladder, railings, brackets,
i 10.25.2 Kg 150.00 131.00 19650.00
gates and similar works

TOTAL (Carried Over to Summary of Civil Works) 19650.0 0.0

F 13.0 PLASTER & PAINTING WORK

15 mm cement plaster on rough side of single or half
1 13.5
brick wall of mix :
i 13.5.2 1:6 (1 cement: 6 coarse sand) Sqm. 443.56 303.90 134797.51
2 13.6 20 mm cement plaster of mix :
i 13.6.2 1:6 (1 cement: 6 coarse sand) Sqm. 690.39 360.10 248609.49
Extra for providing and mixing water proofing material per bag of
in cement plaster work in proportion recommended by 50KG
3 13.21 the manufacturers. Cement 155.51 59.75 9291.86
Used in
Mix
Finishing walls with textured exterior paint of required
4 13.45
shade :
New work (Two or more coats applied @ 3.28 ltr/10
i 13.45.1 sqm) over and including base coat of water proofing Sqm. 1133.95 232.00 263076.15
cement paint applied @ 2.20kg/10 sqm.
Finishing with Deluxe Multi surface paint system for
5 13.48 interiors and exteriors using Primer as per
manufacturers specifications :
Painting Steel work with Deluxe Multi Surface Paint to
give an even shade. Two or more coat applied @ 0.90
i 13.48.3 ltr/ 10 sqm over an under coat of primer applied @ Sqm. 0.00 125.80 0.00
0.80 ltr/ 10 sqm of approved brand and manufacture

Page 2 of 3
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi. Boq.

BOUNDARY WALL
BILL OF QUANTITY

S. No. DSR 2018 Description Unit Qty. DSR RATE DSR Amount NDSR RATE NDSR Amount

TOTAL (Carried Over to Summary of Civil Works) 655775.0 0.0

G 16.0 FENCING WORK

Fencing with angle iron post placed at required
distance embedded in cement concrete blocks, every
15th post, last but one end post and corner post shall
be strutted on both sides and end post on one side only
and provided with horizontal lines and two diagonals
interwoven with horizontal wires, of barbed wire
1 16.18
weighing 9.38 kg per 100 m (minimum), between the
two posts fitted and fixed with G.I. staples, turn buckles
etc. complete. (Cost of posts, struts, earth work and
concrete work to be paid for separately). Payment to
be made per metre cost of total length of barbed wire
used.
i 16.18.1 With G.I. barbed wire metre 146.63 19.05 2793.32
Supplying at site Angle iron post & strut of required size
including bottom to be split and bent at right angle in
2 16.19 opposite direction for 10 cm length and drilling holes Kg 308.35 92.40 28491.72
upto 10 mm dia. etc. complete.

TOTAL (Carried Over to Summary of Civil Works) 31285.0 0.0

Total 3095201.56 0.00

GRAND TOTAL 3095201.6

Page 3 of 3
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Rain Water Harvesting Pit, Estimate
PROJECT :- CONSTRUCTION OF OFFICE BUILDING FOR DENTAL COUNCIL OF INDIA AT RK PURAM, NEW DELHI
Bill of Quantity : RAIN WATER HARVESTING PIT

Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR RATE DSR Amount NDSR RATE NDSR Amount

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic
excavator)/ manual means over areas (exceeding 30cm in depth.
1.5 m in width as well as 10 sqm on plan) including disposal of
1 2.6 excavated earth, lead upto 50m and lift upto 1.5m, disposed
earth to be levelled and neatly dressed.

i 2.6.1 All kinds of soils Cum 149.02 181.85 27098.58

Earth work in excavation by mechanical means (Hydraulic
excavator)/manual means over areas (exceeding 30 cm in depth,
1.5 m in width as well as 10 sqm on plan) including getting out
2 2.7
and disposal of excavated earth lead upto 50 m and lift upto 1.5
m, as directed by Engineer-in-charge.

i 2.7.1 Ordinary rock Cum 31.51 352.45 11105.13

Extra for every additional lift of 1.5 m or part thereof in.
3 2.26

a) 2.26.1 All kinds of soils

i i 1.5 to 3m Cum 36.94 90.40 3339.54
ii ii 3 to 4.5m Cum 32.08 180.80 5800.97
iii iii 4.5 to 6m Cum 32.73 271.20 8875.48
Filling available excavated earth (excluding rock) in trenches,
plinth, sides of foundations etc. in layers not exceeding 20cm in
4 2.25 depth, consolidating each deposited layer by ramming and Cum 54.53 219.65 11976.89
watering, lead up to 50 m and lift upto 1.5 m.

Carriage of material by mechanical transport includeing, loading,

5 1.1.2 unloading and stacking. Earth upto 2km Cum 126.00 149.43 18827.78

TOTAL (Carried Over to Summary of Civil Works) 87024.37 0.00

B 4.0 CONCRETE WORKS

Providing and laying in position cement concrete of specified
1 4.1 grade excluding the cost of centering and shuttering - All work up
to plinth level :
1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40
i 4.1.8 mm nominal size) Cum 3.43 5789.60 19885.89

Centering and shuttering including strutting, propping etc. and

2 4.3 emoval of form work for :

i 4.3.1 Foundations, footings, bases for columns Sqm 6.98 284.85 1987.00
Providing and laying damp-proof course 40 mm thick with
3 4.10 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone Sqm 2.89 347.90 1005.81
aggregate 12.5 mm nominal size).
Extra for providing and mixing water proofing material in cement
4 4.12 concrete Extra for providing and mixing water proofing material per 50 kg 0.74 56.55 41.85
in cement concrete cement

Applying a coat of residual petroleum bitumen of grade of VG-10

of approved quality using 1.7 kg per square metre on damp proof
5 4.13 course after cleaning the surface with brushes and finally with a Sqm 2.89 110.00 318.02
piece of cloth lightly soaked in kerosene oil.

TOTAL (Carried Over to Summary of Civil Works) 23238.57 0.00

C 5.0 REINFORCED CEMENT CONCRETE WORK

Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete work in string courses, bands,
copings, bed plates, anchor blocks,
1 5.12 plain window sills and the like, including the cost of required Cum 4.08 8886.35 36285.64
centering, shuttering but excluding cost of reinforcement, with
1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm
nominal size).
Reinforcement for R.C.C. work including straightening, cutting,
2 5.22 bending, placing in position and binding all complete upto plinth
& above plinth level.

i 5.22.6 Thermo-Mechanically Treated bars. kg 408.33 83.50 34095.57

TOTAL (Carried Over to Summary of Civil Works) 70381.21 0.00

Page 1 of 3
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Rain Water Harvesting Pit, Estimate

Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR RATE DSR Amount NDSR RATE NDSR Amount

D 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of
1 6.1 class designation 7.5 in foundation and plinth in:

i 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 39.78 6376.25 253631.65

TOTAL (Carried Over to Summary of Civil Works) 253631.65 0.00

E 13.0 FINISHING WORK

12 mm cement plaster finished with a floating coat of neat
1 13.7
cement of mix.
i 13.7.1 1:3 (1 cement: 3 coarse sand) Sqm 68.32 340.85 23286.87

TOTAL (Carried Over to Summary of Civil Works) 23286.87 0.00

F 19.0 DRAINAGE WORK

Providing M.S. foot rests including fixing in manholes with
20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse
1 19.15 sand : 6 graded stone aggregate 20 mm nominal size) as per
standard design :

i 19.15.1 With 20x20 mm square bar Each 38.00 422.20 16043.60

Providing and fixing in position pre-cast R.C.C. manhole cover
and frame of required shape and approved quality 19.19.1 L D-
2 19.19 2.5 H D - 20

i 19.19.3.1 Circular shape 560 mm internal diameter Each 4.00 1471.50 5886.00

TOTAL (Carried Over to Summary of Civil Works) 21929.60 0.00

G 22.0 WATER PROOFING WORK

Providing and laying APP (Atactic Polypropylene Polymer)
modified prefabricated five layer 3 mm thick water proofing
membrane, black finished reinforced with non-woven polyester
matt consisting of a coat of bitumen primer for bitumen
membrane @ 0.40 litre/sqm by the same membrane
manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity
70-160 cps. Over the primer coat the layer of membrane shall be
laid using Butane Torch and sealing all joints etc, and preparing
the surface complete. The vital physical and chemical parameters
of the membrane shall be as under : Joint strength in longitudinal
1 14.91.1 and transverse direction at 23°C as 650/ 450N/5cm. Tear Sqm 20.42 535.00 10922.83
strength in longitudinal and transverse direction as 300/250N.
Softening point of membrane not less than 150°C. Cold flexibility
shall be upto -2°C when tested in accordance with ASTM, D -
5147. The laying of membrane shall be got done through the
authorised applicator of the manufacturer of membrane : 3 mm
thick

Extra for covering top of membrane with Geotextile, 120 gsm

non woven, 100% polyester of thickness 1 to 1.25 mm bonded to
2 14.92 the membrane with intermittent touch by heating the Sqm 20.42 99.75 2036.55
membrane by Butane Torch as per manufactures
recommendation.

TOTAL (Carried Over to Summary of Civil Works) 12959.38 0.00

H 23.0 RAIN WATER HARVESTING & TUBEWELLS WORK

Boring/drilling bore well of required dia for casing/ strainer pipe,
by suitable method prescribed in IS: 2800 (part I), including
collecting samples from
different strata, preparing and submitting strata chart/ bore log,
including hire & running charges of all equipments, tools, plants
1 23.2
& machineries
required for the job, all complete as per direction of Engineer -in-
charge, beyond 90 metre & upto 150 metre depth below ground
level.

i 23.2.1.1 All types of soil 300 mm dia Rmt 55.00 597.65 32870.75

Page 2 of 3
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Rain Water Harvesting Pit, Estimate

Sl. No. DSR-2018 DESCRIPTION UNIT QTY. DSR RATE DSR Amount NDSR RATE NDSR Amount

Supplying, assembling, lowering and fixing in vertical position in

bore well, unplasticized PVC medium well casing (CM) pipe of
required dia, conforming to IS: 12818, including required hire and
2 23.3 labour charges, fittings & accessories etc. all complete, for all
depths, as per direction of Engineer-in-charge.

i 23.3.3 200 mm nominal size dia Rmt 55.00 1066.05 58632.75

Supplying, filling, spreading & leveling stone boulders of size
range 5 cm to 20 cm, in recharge pit, in the required thickness,
3 23.5 for all leads & lifts, all Cum 7.54 1326.55 9996.88
complete as per direction of Engineer-in-charge.
Supplying, filling, spreading & leveling gravels of size range 5 mm
to 10 mm, in the recharge pit, over the existing layer of boulders,
4 23.6 in required thickness, for all leads & lifts, all complete as per Cum 7.54 1326.55 9996.88
direction of Engineer-incharge.

Supplying, filling, spreading & leveling coarse sand of size range

1.5 mm to 2 mm in recharge pit, in required thickness over gravel
5 23.7 layer, for all leads & lifts, all complete as per direction of Cum 7.54 1326.55 9996.88
Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS:

4097, including providing gravel fine/medium/ coarse, in
6 23.8 required grading & sizes as per actual requirement, all complete Cum 3.78 1497.70 5660.97
as per direction of Engineerin-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the
7 23.15 bottom of pipe assembly of tubewell as per IS:2800 (part I).

i 23.15.3 200 mm dia Each 1.00 307.75 307.75

TOTAL (Carried Over to Summary of Civil Works) 127462.86 0.00

GRAND TOTAL 619914.51 0.00

Total of DSR & NDSR 619914.51

Page 3 of 3
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Project Name :- Dental Council of India at New Delhi

BOQ:- HVAC WORKS

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

Note: The HVAC contractor shall provide fire shunt relay contact in main
HVAC panel and all AHU panels/DBs along with auto / manual mode selector
switch in the outgoing feeder for AHU Fan, Ventilation & Pressurization fan etc.
to take fire input signal (Potential Free Contact) to trip /switch off them. Cost
shall be included in the panel price quoted by him.

Sub Head 'A' - Machinery

1 DSR(2019)- Variable Refrigerant Volume / Flow Air-conditioning System (Heating &
1.0 Cooling both)
Supply Installation, Testing & Commissioning of modular type Variable
Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable
for cooling and heating, having all hermetically sealed inverter type Scroll
Compressor(s), minimum two compressors for above 14 HP
modules, microprocessor based Controller, top discharge type condensing
unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation
etc.complete as required. The unit shall deliver the rated capacity at AHRI
Conditions and work even at 50°C ambient temperature without tripping. The
unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power
supply. The unit shall be filled with first charge of the refrigerant and ready for
use as required.
Note:Outdoor Theshall
units COPbeatprovided
AHRI conditions
with MS shall
standnot be less than
of suitable size 3.1
dulyand
painted with corrosion resistant paint suitable for outdoor application.Make:
Hitachi,Toshiba,Daikin,Mitshubishi Electric.The units shall be suitable to
operate at New Delhi ambient conditions.
1.1 DSR(2019)- 8 HP Cool / Heat Pump Unit Each 1 131320 131320
1.1
1.2 DSR(2019)- 12 HP Cool / Heat Pump Unit Each 2 196980 393960
1.2
1.3 DSR(2019)- 32 HP Cool / Heat Pump Unit Each 1 525280 525280
1.3
1.4 DSR(2019)- 48 HP Cool / Heat Pump Unit Each 4 787920 3151680
1.4

2 DSR(2019)- INDOOR UNIT-CASSETTE TYPE

2.0
Supply, installation, testing and commissioning of following minimum capacity
4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with
synthetic washable media pre-filter, fan section with low noise fan/dynamically
balanced blower, multispeed
motor, coil section with DX Copper coil, electronic expansion valve, outer
cabinet, drain pump, grill, necessary supports, vibration isolation, cord less
remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz
AC supply, complete, as required. The unit shall have automatic force shut
down provision in case of fire on receiving signal from BMS System. The
cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB
and 19 Degree C WB temperature.Complete as required as per site
conditions.

2.3 DSR(2019)- 1.6 TR Each 3 30204 90612

2.4
2.4 DSR(2019)- 3.2 TR Each 1 32787 32787
2.8

3 DSR(2019)- INDOOR UNIT-DUCTABLE TYPE

4.0
Supply, installation, testing and commissioning of following minimum capacity
and external static pressure VRF/VRV ceiling mounted ductable type Indoor
unit equipped with washable synthetic media pre-filter, fan section with low
noise fan/dynamically balanced blower, multispeed motor, coil section with DX
copper coil, electronic expansion valve, corded remote control, outer cabinet,
vibration isolators, drain pan, other necessary supports etc., suitable for
operation on single phase AC supply 230 V ± 10%, 50 Hz complete as
required. The unit shall have automatic force shut down provision in case of
fire on receiveing signal from BMS System. The cooling capacity of indoor unit
will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB
BOQ HVAC Page 1 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

Low static ductable units (minimum 25 pascal external static pressure)

3.1 DSR(2019)- 1.6 TR Each 2 35259 70518
4.9
Mid Static Ductable units (minimum 45 pascal external static pressure)
3.2 DSR(2019)- 2.0 TR Each 10 38913 389130
3.3 DSR(2019)- 3.4 TR Each 1 47651 47651

4 NSR-1.0 VRV/VRF Central Controller for Indoor & Outdoor Units

Supply, installation, testing & commissioning of Central Controller capable of
controlling of all IDUs, ODUs with spare complete with necessary hardware,
accessories etc. to perform the following functions:

1. Control of IDUs, ODUs Units as above with monitoring of vital parameters

such as temperature sensing & setting, ON/OFF, status etc.
2. Parameters / prohibit function of Each remote controlled unit.
3. Operation of units in individually or in group.
4. Filter status of indoor units.
5. Fault indication
6. Integration with Fire alarm & security system (the units will be switched off Each 1 54260 54260
incase of activation of fire alarm).
7. The central controller will be complete including all hardware & software
from OEM (including wiring) suitable to perfume above function. It should be
user friendly through its touch screen, icon display.Complete as required as
per site conditions.

5 NSR -2.0 Floor Mounted Air Handling Unit (suitable for VRV system With VFD)

Supply, Installation, testing and commissioning of Eurovent certified factory

fabricated double skin type Air Handling Units (BMS compatible) as per
specifications given below:-
AHU Construction:-It shall be made out of 0.8 mm pre -coated Galvanized
steel sheet outside & 0.8 mm plain GI steel sheet inside with 40 mm thick PUF
insulation, factory injected between them by injection moulding m/c, with
density not less than 40 kg/Cum between them. Drain pan (made out of 1.2
mm thick stainless steel (SS Grade 304) sheet insulated with 19 mm think
closed cell nitrile rubber insulation with thermal break profile.
Necessary foundation required & anti vibration pads shall be provided & cost
for the same shall be included in this item.
1) Filter section consisting of pre filter in aluminum casing .Pre-filter section
shall be with non woven synthetic media of 10 micron particle size with an
efficiency of 90%. The quoted price shall also include VCD.
2) Plug Fans/DIDW Backward Curved Belt Driven Fans with aerofoil profile
blade (with min. 70% efficiency) with motor (VFD compatible) ,volume control
damper and duct flexible connection. The supply fan shall be provided with
variable frequency drive and input/output signal compatible to BMS system.
4) Discharge Plenum Section.
COIL- Copper tubes and Aluminum fins 10 fin./inch, Coil size shall be selected
for air velocity of 350 ft./minute & velocity across filters at 350 ft./minute.
Sound level 65 db. at the distance of 2 mtr.(maximum)
Necessary potential free contacts shall be provided for BMS operation.
Space for VFD shall be provided in the AHU. VFD shall be considered as a
separate item.Complete as required as per site conditions.
AHUs capacity shall be as follows:

5.1 NSR-2.1 15000CFM / 34.0TR, 50mmwg SP, Fan motor of required HP Nos. 1 566249 566249
5.2 NSR-2.2 13000CFM / 25.0TR, 50mmwg SP, Fan motor of required HP Nos. 3 487498 1462494
5.3 NSR-2.3 4500CFM / 9.0TR, 50mmwg SP, Fan motor of required HP Nos. 1 250206 250206

6 NSR -3.0 Ceiling Suspended Treated Fresh Air Unit (suitable for VRV System)

BOQ HVAC Page 2 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
Supply, Installation, testing and commissioning of Eurovent certified factory
fabricated double skin type Treated Fresh Air Units (BMS compatible) as per
specifications given below:-
TFA Construction:-It shall be made out of 0.6 mm pre -coated Galvanized steel
sheet outside & 0.6 mm plain GI steel sheet inside with 46mm thick PUF
insulation factory injected between them by injection moulding m/c, with
density not less than 40 kg/Cum between them. Drain pan (made out of 1.2
mm thick stainless steel (SS Grade 304) sheet insulated with 19 mm think
closed cell nitrile rubber insulation with thermal break profile.
Necessary foundation required & anti vibration pads shall be provided & cost
for the same shall be included in this item.
1) Filter section consisting of pre filter in aluminum casing .Pre-filter section
shall be with non woven synthetic media of 10 micron particle size with an
efficiency of 90%. The quoted price shall also include VCD.
2) Plug Fans / DIDW backward curved belt driven fans with aerofoil profile
blade (with min. 70% efficiency) with motor, volume control damper and duct
flexible connection. The supply fan shall be provided with input / output signal
compatible to BMS system for monitoring, Squirrel cage induction motors
suitable for 415
4) Discharge ± 10%Section.
Plenum volts, 50 Hz, AC supply & high efficiency (IE-3
COIL- Copper tubes and Aluminum fins 10 fin./inch, Coil size shall be selected
for air velocity of 350 ft./minute & velocity across filters at 350 ft./minute.
Sound level 65 db. at the distance of 2 mtr.(maximum)
Necessary potential free contacts shall be provided for BMS
operation.Complete as required as per site conditions.

6.1 NSR-3.1 1400CFM / 10.0TR, 50mmwg SP, Fan motor of required HP Nos. 1 130061 130061

NSR-4.0 Supply, installation,testing & commessioning of Electronic Type Expansion Kit

for above AHU with Communication PCB with Sensors, Corded Self
Diagnostic Type Digital Thermostat, Y-joints etc which shall be supplied by
the OEM of VRV/VRF system.
NSR-4.1 15000CFM / 34.0 TR Nos. 1 162780 162780
NSR-4.2 13000CFM / 25.0 TR Nos. 3 108520 325560
NSR-4.3 4500CFM / 9.0 TR Nos. 1 54260 54260
NSR-4.4 1400 CFM/10.0 TR Nos. 1 54260 54260

7 NS -5.0 VFD for Air Handling units

Supply, installation, testing & commissioning of VFD designed for HVAC
applications with built-in PID controller, control panel (keypad & display) , IP-55
enclosure (for outdoor applications) & IP-20 enclosure (for indoor applications)
for use on AHU fans. The display should be in alpha-numeric characters and
programming facility should be in user-friendly HVAC terminology. VFD’s shall
have built-in harmonic filters with THDI less than 5%. Each VFD panel to be
provided with digital display showing electrical parameters like voltage, current
and power consumption. Each VFD shall be installed in a dedicated
external/internal enclosure and the inter connecting wires between driver and
MCC shall be included. Necessary transformer, power adapters, sensors, relay
Note :This item shall only be considered if AHUs are not provided with

7.1 NSR-5.1 7.5 HP/ 5.5 KW Nos. 4 51775 207100

7.2 NSR-5.2 3.0 HP/ 2.2 KW Nos. 1 38446 38446

8 NSR-6.0 HI WALL SPLIT UNITS

BOQ HVAC Page 3 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
Supply, Installation, testing and commissioning of Air-cooled DX type Hi-wall
split air conditioners each comprising an outdoor unit(s) consisting of
hermetically sealed compressor suitable for operation on 230V, 50Hz, 1 Phase
AC supply, air cooled condenser, condenser fan along with Cooling
thermostats etc. with outer casing and indoor fan coil unit consisting of
centrifugal fans, fan motor, DX cooling coil, outer casing, filter, control and
power panel with remote etc. entire cabling and wiring from indoor to outdoor,
insulation and with full charge of refrigerant gas and oil, supports, canvas
connection etc. complete as per drawings. The indoor and outdoor units shall
be with structural steel supports, angles, rods etc. The quoted price shall also
include 24G soft copper refrigerant piping (of required length from indoor to
outdoor) with 13 mm "O" class factory backed nitrile rubber with aluminum foil
from outdoor unit to indoor unit complete with insulation, refrigerant charging,
PVC drain piping with 6mm thick nitrile rubber insulation, supports, clamps,
fittings, connections, sleeves, supports, MCB, stabilizer etc. from main panel to
the unit. The refrigerant used shall be CFC/HCFC free R-410 A. Also, EER
8.1 NSR-6.1 1.5 TR Unit (For Elec Room) - 2W+2S Nos. 4 48569 194276

Supply, installation, testing and commissioning of VARIABLE AIR VOLUME

(VAV) BOXES complete with leakage proof damper, differential pressure
9 NSR-7.0 sensor, ,motorized aluminium construction damper with actuator (UL
approved), Rapid Average Pitot tube; Air Flow Straightner (Honey-Comb
patterned).Make
LCD touch screen Cynor,Ruskin
type coolingTitus,Belimo
& Heating thermostat with all the parameter
control, differential pressure sensor,24 Volt power supply unit for each VAV
box, controller capable of accepting analogue/digital signal from thermostat
and output to damper actuator.The thermostat should have capacitive touch
button with large display wired control port should be controlled by mobile
app(optional).Complete as required as per site conditions.

9.1 NS-7.1 800 CFM-990 CFM Nos. 1 42316 42316

9.2 NS-7.2 1000 CFM-1200 CFM Nos. 1 42316 42316
9.3 NS-7.3 1250 CFM-1500 CFM Nos. 1 43238 43238
9.4 NS-7.4 1600 CFM-2000 CFM Nos. 1 45314 45314
9.5 NS-7.5 2000CFM- 3000 CFM Nos. 1 47850 47850
9.6 NS-7.6 3000CFM- 5000 CFM Nos. 1 49349 49349
9.7 NS-7.7 5000CFM- 10000 CFM Nos. 1 55345 55345

Supply, installation, testing and commissioning of controler Modulating

motorised assembly for pressure independent volume control with
programmable advanced application specific controller having digital
differential pressure sensor, 4 UI & 4 UO, wired wall module port &
communication should only be BACNET over IP for all VAV controllers; &
10 NS-8.0
necessary power supply circuit suitable for 220V. Mapping shall be required for
monitoring individual room temperature, air flow and damper position for areas
conditioned through VAV boxes.Quoted price shall be inclusive of wiring in GI
conduit between Controler and individual VAV Boxes.Complete as required as
per site conditions.

10.1 NS-8.1 Upper Ground Floor Nos. 1 83306 83306

10.2 NS-8.2 First Floor Nos. 1 83306 83306
10.3 NS-8.3 Second Floor Nos. 1 83306 83306
10.4 NS-8.4 Third Floor Nos. 1 83306 83306

Supply, installation, testing and commissioning of duct mounted air purification

system, Advance Oxidation Process (AOP) cell with the capability to produce
friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides
Ions with quad metalic coating (Rohdium, silver, copper and titanimum) and
duly enclosed by a poly casing tube that should prevent glass or mercury
11 NS-9.0 leakage into the conditioned/ served space. The honeycomb matrix shall not
be accepted. The units should be designed after undertaking a load factor
calculation for each specific area where the equipment is to be installed. The
load shall clearly state the number of units required vis-à-vis the wattage of the
units for submital. The system shall be capable of reducing microbial bacteria,
virus and spores,VOC, odors and particulates matter.Make:VS

BOQ HVAC Page 4 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

11.1 NS-9.1 For Stilt Floor AHU (4500 CFM) Each 1 109876 109876
11.2 NS-9.2 For Upper Ground/Second/Third Floor AHU (13000 CFM) Each 1 148943 148943
11.3 NS-9.3 For First Floor AHU (15000 CFM) Each 1 148943 148943
11.4 NS-9.4 For Fourth Floor TFA (1400 CFM) Each 1 92296 92296

12 NSR-10.0 Cabinet Type Inline Fans

Supplying, installing, testing & commissioning of INLINE FANS(Cabinet Type)
AMCA Certified (For Air and Sound Performance) suitable for installing in any
position in vertical or horizontal ducts. The casing shall be double skin,
internally acoustically lined and constructed of galvanised steel. The inline fan
shall be with backward/forward curve centrifugal impeller fitted with
maintenance free external rotor motor, flexible connections at the discharge &
inlet. The motor shall be suitable for 220±10% volt single phase 50 cycles AC
supply. Quoted price shall be inclusive of electronic speed regulator and wiring
between fan & speed regulator for single phase fans. Incase of 3 phase fans
quoted price shall be inclusive of DOL starter panel with cabling between
starter panel and fan. The incoming power supply to speed regulator / starter
12.1 NSR-10.1 Air Quantity : 300 CFM
Static Pressure : 20 mm wg
Motor rating : As Required
Duty : Toilet Exhaust Nos. 5 14379 71895
12.2 NSR-10.2 Air Quantity : 200 CFM
Static Pressure : 20 mm wg
Motor rating : As Required
Duty : Toilet Exhaust Nos. 5 12615 63075

13 NSR-11.0 Propeller Fans

Supplying, installing, testing and commissioning of direct driven plastic body
PROPELLER FANS . Each fan shall be complete with permanent split
capacitor or shaded pole motor, mounting plate with light weight type plastic
ABS impellers with aerofoil contours for high efficiency & low noise & gravity
louvers for weather protection as required.Complete as required as per site

Air Quantity : 250 CFM , 2.5 mm St. Pr., 900 RPM or as per OEM, fan
13.1 NSR-11.1
suitable for 220 ± 5% volts 50 cycles, 1 phase AC supply.
Power : As Required
Duty : Toilet & Pantry Exhaust Nos. 25 10174 254350

Air Quantity : 1000 CFM , 2.5 mm St. Pr., 900 RPM or as per OEM, fan
13.2 NSR-11.2
suitable for 220 ± 5% volts 50 cycles, 1 phase AC supply.
Power : As Required
Duty : Pump Room Exhaust Nos. 2 11259 22518

14 NSR-12.0 AXIAL FLOW FAN (AMCA Certified for Sound & Preformance):
Supplying, installation, testing and commissioning of AMCA Certified (For Air
and Sound Performance) ceiling hung / floor mounted vane/tube axial flow
fans of following capacity with GSS casing/ standard M.S. construction and
aluminium alloy impellers with high efficiency aero-foil sections, blades, the
impeller directly driven by TEFC induction motor should be of high efficiency
IE2 for Emergency Supply, Pressurization and Smoke Exhaust Fans and IE3
for Normal Supply, and Exhaust Fans suitable for 3 Phase 50 Hz 415V ± 10
%. Motor shall be class 'F' insulation for Fresh Air and Pressurization Fans
and class 'H' insulation for Exhaust Fans. Fire rated flexible connection etc.
including all accessories complete as required and as per specifications. Motor
of exhaust fans shall be of high temperature resistance "Class H Smoke
Spill" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for
high temprature. Motor make shall be same as mentioned on the fire
certificate. Fan total efficiency should not be less than 70%. All the fans shall
be hot dip galvanized with minimum 220 GSM Zinc Coating and complete with
bird screen at inlet. Suitable TP isolator within MS enclosure should be
provided. Gravity louvers will be provided at the discharge of the fan so as to
The fans operating under normal modes shall have low sound level not
exceeding more than 75 dB(A)at three meter distance at both ends when
measured in hemispherical reverberant room conditions. To achieve specified
dB(A) level sound attenuators shall be provided at inlet / outlet and included in
the cost.The fans operating under emergency modes shall have sound level
not exceeding more than 85 dB(A) at three meter distance at both ends when
BOQ HVAC measured in hemispherical reverberant room conditions.Page 5 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

14.1 NSR-12.1 Air Quantity : 18000 CFM

Static Pressure : 30 mm wg
Motor Rating : 7.5 HP (Suggested)
Insulation : Class F
Duty : Staircase Pressurisation Nos. 2 80728 161456

14.2 NSR-12.2 Air Quantity : 14000 CFM

Static Pressure : 30 mm wg
Motor Rating : 7.5 HP (Suggested)
Insulation : Class F
Duty : Lift Well Pressurisation Nos. 3 78557 235671

14.3 NSR-12.3 Air Quantity : 10000 CFM

Static Pressure : 40 mm wg
Motor Rating : 7.5 HP (Suggested)
Insulation : Class H
Duty : Smoke Exhaust Nos. 4 80649 322596

14.4 NSR-12.4 Air Quantity : 10000 CFM

Static Pressure : 30 mm wg
Motor Rating : 5.0 HP (Suggested)
Insulation : Class F
Duty : Lift Lobby Pressurisation Nos. 1 58770 58770

14.5 NSR-12.5 Air Quantity : 6500 CFM

Static Pressure : 40 mm wg
Motor Rating : 5.0 HP (Suggested)
Insulation : Class H
Duty : Basement Ventilation Nos. 4 53860 215440

14.6 NSR-12.6 Air Quantity : 6500 CFM

Static Pressure : 40 mm wg
Motor Rating : 5.0 HP (Suggested)
Insulation : Class F
Duty : Basement Ventilation Nos. 2 43709 87418

14.7 NSR-12.7 Air Quantity : 3500 CFM

Static Pressure : 40 mm wg
Motor Rating : 3.0 HP (Suggested)
Insulation : Class H
Duty : Smoke Exhaust Nos. 2 39256 78512

14.8 NSR-12.8 Air Quantity : 3500 CFM

Static Pressure : 25 mm wg
Motor Rating : 1.5 HP (Suggested)
Insulation : Class F
Duty : Smoke Makeup Nos. 1 34003 34003

Supply, installing, testing and commissioning of Ductless Ventilation / AMCA

Certified (Air & Sound Performance) Jet fans (315 mm Dia ) for Normal
ventilation and Smoke Extraction application for car parking. The complete fan
assembly with its Casing, impeller & motor (not only the motor or one of the
15 NSR-13 item) shall be sourced from one manufacturer and certified as tested for 300
Deg.C for 2 hours operation with sound attenuator with bird screen at inlet an
outlet of the fan CMH - 3564/6984. Adequate number of CO sensors, electrical
starter panels with power / control cabling for 3 phase/ 1 phase fans and logic
controller with necessary
Each fan shall be AMCA control cabling
Certified will form
& complete part
with of the
Dual speed motor. Casing
shall be made Galvanized Aluminum. The Motor shall be run on the electrical
power suitable for 50Hz,CFD analysis will be carried out for all the areas
leading to the selection of the fans. Cost of CFD analysis for Each of the area
shall be included in the quoted rates. Complete as required as per site
15.1 NSR-13.1 Jet fans as described above (For B2 & B1 ventilation) Each 6 75421

16 NSR-14 DUAL SPEED JET FAN ELECTRICAL PANEL

BOQ HVAC Page 6 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
The motor shall be suitable for 415 ± 10% or 230 ± 10% volts, 50 cycles,A/C
power supply. Quoted price shall be inclusive of electrical panel with suitable
rating starters for dual speed operation. Control wiring power cabling , dry
contact for fire integration & conduiting / cable tray between electrical panel
Set 2 61042
and fan shall be also be included. One panel will take care of 3 nos. of jet fans.
The system shall be complete in all respects.Make:As per OEM. Complete as
required as per site conditions.

Note: Detailed CFD analysis from the OEM shall be carried by contractor

17 NSR-15.0 Factory Fabricated Double Skin Air Washer

Supply, installation, testing and commissioning of factory fabricated
Double Skinned Air-washer unit floor mounted type fabricated out of
extruded aluminum section with 0.6mm pre-plasticized / pre-coated
Galvanized steel sheet outside & 0.6 mm plain Galvanized steel sheet inside
with blower, blower section and blower motor TEFC (IE-3) type suitable
for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package,
wet section & tank shall be made of 18 G stainless steel. The Air-washer
shall be complete with fill of depth 200 mm & face velocity across the fill
shall be limited to 152 MPM. The Air-washer shall have an efficiency
of 90% & shall be complete with water circulation pump -2 Nos.(1W+1S),
GI B Class interconnecting piping, Aluminum viscous filters. makeup, quick fill
and drain connections, Butterfly/Gate valves for Pumps, make up, drain &
quick fill connections of Sump, 2 Nos. pumps of suitable capacity (1W +1 S), Y
strainers
The and necessary
Air-washer shall fittings
have etc.
an efficiency of 90% & shall be complete
with water circulation pump, GI B Class interconnecting piping & valves,
Aluminum viscous filters, fire retardant double canvass connection etc. The
air washer panels shall be insulated with 23mm thick & 36 Kg/m³
density PU foam. The Air washer shall conform to specification given in the
tender & shall be of following capacity. Motor Kw is indicative only, actual as
per requirement to be included during installation.. Complete as required as
17.1 NSR-15.1 Duty: Kitchen
Air Qty : 5000 CFM
Static Pressure : 50 mm wg
Fan Motor HP : 3.0 HP(Suggested) or as per requirement
Pump Motor HP : 1.5 HP (Suggested) or as per requirement Set 1 199242 199242

18 NSR-16.0 Dry Scrubber With Fan

Supply, Installation, Testing and Commissioning of Scrubber each comprising
of extract air intake section, electrostatic precipitation technology, dry type air
cleaner to remove oil, smoke and fumes from exhaust air, as per the
Specifications. Electrostatic section shall be made of 16 gauge galvanised
sheet, high bake epoxy powder coated, washable type aluminium mesh filters,
stainless steel spiked ionizers to create high voltage DC field, aluminum
collector plates which should be alternatively charged positive and negative
with large collecting area with 14" deep cell, to work as magnet for charged
smoke and oil particles. Average efficiency of 90-95% in single pass as per
ASHRAE test method. Electrostatic Precipitator should be able to charge
particles from 0.01 micron to 10 microns through solid state power supply.
Collector cell should be of permanent type and incorporate slide out facility for
easy removal for cleaning. Power supplies shall be 100% solid state UL Listed,
Module
Operatingof Voltage
capacity:above
220V,3000
50 HzCFM shall be equipped with Pulse width
Ionizing Voltage : 12.5 to 13 KVDC
Collector Cell Voltage : 6 to 6.5 KVDC
Power Consumption : Not more than 50W per cell.
DIDW (double inlet double width) centrifugal fan as per specification, with
statically and dynamically balanced backward curved blades, galvanized steel
housing, maintenance free bearings, belt driven complete with totally enclosed
fan cooled squirrel cage induction motor, centrifugal fan belt drive and
vibration isolators. Motor shall be suitable for 415±10% volts, 50 cycles, 3
phase AC supply & meeting criterion as per ASHRAE standard 90.1-2016 and
high efficiency (IS 12615). Minimum 75 mm (WC) external static pressure after
fan outlet. . Complete as required as per site conditions.
18.1 NSR-16.1 Duty : Kitchen Exhaust
Capacity : 5500 CFM
Static Pressure : 75 mm wg
BOQ HVAC Page 7 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
Fan Motor HP : 5.0 HP or as per requirement Set 1 271299 271299

Supply, Installation and commissioning of Non recirculating centrifugal Air

Curtains with following specifications:-
Artistically designed curvaceous body constructed in aluminium extruded
powder coated sections with powder coated sheet metal base and mounting
plates. Motors constructed in aluminium body to enable rapid cooling, with
19 NSR-17.0 copper winding, bearing based motors made in CRNO core to run continuously
for 24X7 operation, with thermal overload
protection.Make:Mitzvah,Russell,Euronics.
Dynamically balanced centrifugal Blowers made in virgin plastic, with
aerodynamically designed fins to deliver high volume of air., the suction grills
should be made in plastic. Air Curtain should have dual speed with max.
Velocity at Nozzle
Max. Velocity between
~ 21/16 m/s; 19-21 m/s. Air curtain should be coupled with the
19.1 NSR-17.1 Dual Speed; Al Chassis with CRC Plates Nos. 1 22382 22382
Door 2100W x 2100H
Max. Velocity ~ 21/16 m/s;
19.2 NSR-17.2 Dual Speed; Al Chassis with CRC Plates Nos. 1 22382 22382
Door 1500W x 2100H

Total of Sub Head 'A'- Machinery 4832938 6779971

Sub Head-'B'- Piping

20 NS-18 Supply, installation, testing & commissioning Refrigerant 'Y'Joint (pair) required 50 10201 510050
for distribution of refrigerant in copper piping etc. complete as per Nos.
specifications.
21 DSR(2019)- Supply, Installation, testing and commissioning including vaccumiazation and
5.0 Nitrogen testing of following nominal sizes of soft/hard drawn copper
refrigerant piping for VRV/VRF system, complete with fittings, with suitable
adjustable ring type hanger supports, jointing/brazing including accessories,
insulated with XLPE Class-O tubular insulation/with Class-O closed cell
elastometric nitrile rubber tubular sleeves sections of specified thickness as
given below for Suction and Liquid lines, all accessories as per specifications
etc. as required : Make:Rajco,Mandev,Hindustan.. Complete as required as
21.1 DSR(2019)- 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 20 245 4900
5.1 insulation
21.2 DSR(2019)- 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 80 331 26480
5.2 insulation
21.3 DSR(2019)- 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 80 466 37280
5.3 insulation
21.4 DSR(2019)- 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 70 588 41160
5.4 insulation
21.5 DSR(2019)- 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 85 707 60095
5.5 insulation
21.6 DSR(2019)- 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 100 865 86500
5.6 insulation
21.7 DSR(2019)- 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 55 1022 56210
5.7 insulation
21.8 DSR(2019)- 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 78 1108 86424
5.8 insulation
21.9 DSR(2019)- 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick Rmt 55 1170 64350
5.9 insulation
21.10 DSR(2019)- 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick Rmt 20 1230 24600
5.10 insulation
21.11 DSR(2019)- 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick Rmt 95 1265 120175
5.11 insulation
21.12 DSR(2019)- 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm Rmt 20 1309 26180
5.12 thick insulation

22 NS-19 Providing & fixing control cum transmission wiring of 2 core x 1.5 sqmm copper Rmt 500 80 40000
in cable tray with refrigerant piping between indoor units and outdoor units and
indoor units and wired controllers. Complete in all respect as required at site.

23 NSR-20.0 Drain Pipings

BOQ HVAC Page 8 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
Supply & installation, testing and commissioning of Rigid heavy class PVC
piping complete with fittings, supports as per specifications and duly
insulated with 6 mm thick nitrile rubber tubular insulation with factory
laminated GC cloth.Complete as required as per site conditions.
23.1 NSR-20.1 25 mm dia Rmt 125 117 14625
23.2 NSR-20.2 32 mm dia Rmt 20 165 3300
23.4 NSR-20.3 40 mm dia Rmt 45 252 11340

Total of Sub Head-'B'- Piping 634354 579315

Sub Head 'C' - Air Distribution

Supply, installation, balancing and commissioning of factory fabricated GSS

sheet metal rectangular/round ducting complete with neoprene rubber gaskets,
elbows, splitter dampers, vanes, hangers, supports etc. as per approved
24 16.12.1
drawings and specifications of following sheet thickness complete as required..
Complete as required as per site conditions.

24.1 16.12.1.1 Thickness 0.63 mm sheet (24 Gauge) Sqmt 1100 983 1081300
24.2 16.12.1.2 Thickness 0.80 mm sheet (22 Gauge) Sqmt 100 1154 115400
24.3 16.12.1.3 Thickness 1.00 mm sheet (20 Gauge) Sqmt 110 1273 140030
24.4 16.12.1.4 Thickness 1.25 mm sheet (18 Gauge) Sqmt 65 1677 109005

Supply, installation, testing, balancing and commissioning of fabricated at site

GSS sheet metal rectangular/round ducting complete with neoprene rubber
gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per
25 16.12.2
approved drawings and specifications of following sheet thickness complete as
required. . Complete as required as per site conditions.

25.1 16.12.2.1 Thickness 0.63 mm sheet (24 Gauge) Sqmt 100 942 94200
25.2 16.12.2.2 Thickness 0.80 mm sheet (22 Gauge) Sqmt 20 1104 22080
25.3 16.12.2.3 Thickness 1.00 mm sheet (20 Gauge) Sqmt 10 1458 14580
25.4 16.12.2.4 Thickness 1.25 mm sheet (18 Gauge) Sqmt 10 1615 16150

Note-All hanging and support of ducts shall be with Hangers & Supports
complete with end fixing in accordance with the approved shop drawings
and as required by the specifications.
Supply, fabrication, installation, testing & commissioning of Kitchen duct with
26 NSR-21.0 wire wrapping complete in all respects, on kitchen exhaust ducts to provide
minimum 1 Hr fire rating.. Complete as required as per site conditions.
26.1 NSR-21.1 16 gauge MS duct work welded construction** Sqmt 100 2645 264500

Note- 1. All hanging and support of ducts and pipes shall be with
Gripple/Hilti Hangers & Supports complete with end fixing in accordance
with the approved shop drawings and as required by the specifications.
** Duct shall have fire rated coating compound STARCOAT – CRC /
FLAMEBAR. Fire rated coating compound used for construction of fire
rated ductwork shall be protected with minimum 0.7mm to 1mm nominal
thickness tested to properties as per the requirements of BS 476: 6 &
amp; 7, including non-combustibility Class O and fire propagation - Class
1 surface spread of flame & amp; materials in accordance with building
regulations.

Supply, installation, testing and commissioning of GI volume control duct

27 16.13 damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, Sqmt 10 6500 65000
flanges etc, as per specifications & as required.

Supply, fabrication, installation and testing of non-porous flexible

28 NSR-22.0 connections constructed of fire resistance flexible, double canvas Sqmt 50 5426 271300
connection with resistoflex material as per the approved shop drawings.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills
29 16.15 Sqmt 3 8480 25440
with aluminium volume control dampers as per specifications.
BOQ HVAC Page 9 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

Supplying & fixing of powder coated extruded aluminium Return/Exhaust Air

30 16.16 Sqmt 12 5507 66084
Grills with louvers but without volume control dampers as per specifications.

Supplying, Installation, testing & commissioning of supply air diffusers of

31 16.17 powder coated aluminium with aluminium volume control dampers with anti Sqmt 20 11363 227260
smudge ring & removable core as per specifications complete as required.

Supplying, Installation, testing & commissioning of Return air diffusers of

powder coated aluminium without volume control dampers with anti smudge
32 16.18 Sqmt 20 7559 151180
ring & removable core as per specifications complete as required.

Supply, installation, testing & commissioning of thermal insulated flexible duct

33 16.19 of following sizes duly supported at regular interval as per site requirement etc.
complete as required as per specifications.

33.1 16.19.1 200mm dia Rmt 50 538 26900

34 16.20 Fire Dampers

Supplying, Fixing, testing and commissioning of fire dampers in supply air
duct/main branch and return air path as and where required of required sizes
i/c control wiring,the damper shall be motorized and spring return so as to
close the damper in the event of power failure automatically and open the `
same in case of power being restored. The spring return action shall be inbuilt
mechanism and not externally mounted. The damper shall also be closed in
the event of fire signal complete as required and as per specifications.

34.1 16.20.1 Fire damper(150 mm deep) Sqmt 18.5 9883 182836

34.2 16.20.2 Control Panel with actuator(10Nm Torque) & Wiring Sqmt 21 9212 189358

35 NSR-23.0 Door Transfer Grill

Supply, installatio, testing, balancing and commissioning of extruded
aluminium powder coated door transfer grill mesh with matching flange at rear
side as required.. Complete as required as per site conditions.
35.1 NSR-23.1 600 mm X 150 mm Size Nos 37 671 24827

36 NSR-24.0 Louvers

Supplying, installing, testing and commissioning of Fresh Air powder coated

Anodized extruded aluminium construction fresh air louvers (50 mm deep)
36.1 NSR-24.1 Sqmt 5 11937 59685
(Fresh air louver with VCD , bird screen & rattle-free) complete as per
specification.. Complete as required as per site conditions.

Supplying, installing, testing and commissioning of Exhaust Air powder coated

Anodized extruded aluminium construction fresh air louvers (50 mm deep) air
36.2 NSR-24.2 Sqmt 3.5 5562 19467
louver without VCD , bird screen & rattle-free)complete as per specification..
Complete as required as per site conditions.

Supply, installation, testing & commissioning of galvanised steel construction

Non Return Damper with in ducts wherever required as per approved shop
37 NSR-25.0 Sqmt 1.5 5290 7935
drawings.Complete as required as per site conditions.

DUCT THERMAL & ACOUSTIC INSULATION

Supplying and fixing of following thickness duly laminated aluminum foil of mat
finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after
38 16.23 applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50
mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete
as per specifications and as required.Make-

BOQ HVAC Page 10 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

38.1 16.23.1 19 mm thick Sqmt 800 697 557600

38.2 16.23.2 25 mm thick Sqmt 90 896 80640

39 NSR-26.0 Supply, installation testing and commissioning of 10 mm thick duct acoustic

insulation Inside the Duct with open cell nitrile rubber to be applied using
manufacturer's recommended Rubber based Adhesive in a blend of Sqmt 85 1031 87635
solvents.complete as required and as per specifications.Make-
Aerofoam,Supreme,Vidoflex.Complete as required as per site conditions.

Total of Sub Head-'C'- Air Distribution 3165042 735349

Sub Head 'D' - HVAC Electrical

40 NSR-27.0 HVAC Panel for VRV

Design, fabrication, assembly, wiring and supply of front operated dead front
cubicle type compartmentalised as per Form 3B, rear access free standing,
dust and vermin proof (IP 65 ingress protection) main switchboards suitable for
use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical
fault level of 25 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets
with hinged, gasketted (metal based neoprene) and lockable doors having
structural reinforcement with suitable angle/channel/T/flat sections including 3
mm thick gland plates on top and bottom and including lifting hooks and
including GI earth strip of required size with 2 nos earthing terminals and
including powder coated paint finish of approved shade over metal surface
Each Motor control Centre(MCC)/Panel shall include cost of cabling, wiring,
control wiring & inter locking in order to execute the required sequence of
operation.Make-KEPL,Ambit switch Gear,CWS,Advance.
A separate set of CTs to be provided for wiring from CT’s and voltage
transducers to be brought on to separate set of terminals.
Note : MCCB’s shall be motor duty and suitable for 25 KA (ICS) fault current
Motor Control Centre (415 V) consisting of
a. Incoming
One No.400 amps 4 Pole MCCB ICU=ICS=25KA with PRMB-2 having front
operatinh handle with door interlock and as per preamble above complete with
i. 0 - 500 volts 96 x 96 sq mm digital voltmeter with selector switch - 1 Set

ii. 0 - 400 amps 96 x 96 sq mm digital ammeter with 400/5 amps CT’s and
selector switch - 1 Set
iii. Over voltage tripping mechanism for persistent voltage exceeding 110% of the
rated voltage for more than 5 minutes - 1 Set
iv. Phase indicating lamps, with toggle switches.
v. Terminals to receive XLPE insulated Aluminium cables
Busbar
TPN bus bars shall be of aluminium and shall be sleeved. Phase bus bars
shall be rated at 500 amps and neutral bus bar shall be of 50% capacity
suitable to withstand symmetrical fault level of 25KA of 415 V.
Maximum density of aluminium bus bars for current carrying capacity shall be
one amp per square mm.
Outgoing
a. 4 No.25 amps MCCB outgoing feeders to 8 HP & 12HP VRV outdoor unit
.Each of these compartment shall contain CT operated digital ammeter of 0-60
amps range with selector switch, and an indicating lamp with MCB and toggle
b. switch for ‘ON’
15 No.40 ampsstatus.(1 spare butfeeders
MCCB outgoing without to
metering
16 HP )VRV outdoor unit .Each of
these compartment shall contain CT operated digital ammeter of 0-60 amps
range with selector switch, and an indicating lamp with MCB and toggle switch
for ‘ON’ status.(1 spare but without metering )
Supplying,Receiving, fixing, testing & commissioning of MCC/Panel as
described above.Complete as required as per site conditions. Set 1 339124 339124

41.0 NSR-28.0 CONTROL PANELS FOR Axial Flow Fans

BOQ HVAC Page 11 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
Design, manufacture, supply, installation, testing and commissioning of the
following cubicle type, dead front, sheet steel, wall mounted control panels,
including anchoring into the wall, wiring terminating into MCCB and copper
earthing, in each panel shall be provided by the electrical contractor.Complete
as required as per site conditions.
All outgoing shall be provided with Stop /Manual /Auto selector switch to
facilitate operation through BAS. All starters shall be provided with potential
free Contact for Connections to Building Automation System.Make-
KEPL,Ambit switch Gear,CWS,Advance.
All wiring and copper earthing of motors from the panel shall be included.
The panel shall include the following components & accessories.
MCCB as per the ratings given below, suitable for motor duty and able to
a.
withstand fault level of 20 KA.
b. DOL / SD starter as per HP ratings
c. Terminal block for power distribution.
d. Contractor, over load relay with built in single phasing protection.
e. Phase indicating lights and indicating light for ON status.
f. Digital voltmeter and digital ammeter with selector switches.
g. Time delay relay for delayed automatic restart of air handling unit motor.
Wiring/Control wiring from fire damper panel to AHU/Fan section panel to fire
h. damper motor & micro switch for stopping the fan when fire damper closes(as
required by application)
For on/off/remote and local operation, 3 pole single throw switch shall be
i. provided in each AHU/Fan Section panel to facilitate override of the automatic
operation.
All starters shall be provided with suitable potential free contact for
j.
connections to the Building Automation System.
3 Nos of Single Pole MCB's Shall be provided at the incoming section of the
k.
starter panel for fire damper actuator & as a spare.
The number of control panels shall be as follows.
41.1 NSR-28.1 Suitable Size MCB, 1.5 HP with DOL Starter Nos. 1 23006 23006
41.2 NSR-28.2 Suitable Size MCB, 3.0 HP with DOL Starter Nos. 2 23318 46636
41.3 NSR-28.3 Suitable Size MCB, 5.0 HP with DOL Starter Nos. 7 23318 163226
41.4 NSR-28.4 Suitable Size MCB, 7.5 HP with DOL Starter Nos. 9 23332 209988

42.0 NSR-29.0 AHU Panel-1 (Stilt Floor)

A INCOMER

1 No. 25A TP MCCB, 25 kA breaking capacity with thermal release and

adjustable setting and with rotary handle.

B METERING & INDICATION

1 Set - digital multifunction meter (showing harmonics along with all other
electrical parameters such as voltage current, Hz, KW, KWHr, PF.) with RS
485 port with matching cast resin CT's
1 Set - 0-500V 96 sqmm Voltmeter with selector switch, 3 No. phase indicating
LED lamp to show the incoming power with control SP MCB.
1Set of indicating LED lamps for MCCB On/Off with protective SP MCB's.

1 Set of CTs of the ratio 25/5A with class 0.5 Accuracy for Metering, burden 15
VA

C BUSBAR
32A TPN Aluminium Bar with colour coded PVC Sleeves

D OUTGOINGS
2 Nos. 16A TP MCB (including 1 no spare)
5 Nos. 10A DP MCB
3 Nos. 16A SPN MCB c curve 10 KA

Note- Necessary wiring and interlocking for the above equipments shall
be done with the Fire Alarm system such that required fan gets actuated
and shut off the AHU in case of fire as per fire zones. No/NC contacts &
supply arrangements shall also be spared for the fire damper actuation &
control.

BOQ HVAC Page 12 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

Supplying,Receiving, fixing, testing & commissioning of AHU Panel-1

(Stilt Floor) as described above.Complete as required as per site Set 1 101737 101737
conditions.

43.0 NSR-30.0 AHU Panel-2 (UGF/1F/2F/3F)

A INCOMER

1 No. 32A TP MCCB, 25 kA breaking capacity with thermal release and

adjustable setting and with rotary handle.

B METERING & INDICATION

1 Set - digital multifunction meter (showing harmonics along with all other
electrical parameters such as voltage current, Hz, KW, KWHr, PF.) with RS
485 port with matching cast resin CT's
1 Set - 0-500V 96 sqmm Voltmeter with selector switch, 3 No. phase indicating
LED lamp to show the incoming power with control SP MCB.
1Set of indicating LED lamps for MCCB On/Off with protective SP MCB's.

1 Set of CTs of the ratio 40/5A with class 0.5 Accuracy for Metering, burden 15
VA

C BUSBAR
40A TPN Aluminium Bar with colour coded PVC Sleeves

D OUTGOINGS
2 Nos. 32A TP MCCB (including 1 no spare)
5 Nos. 10A DP MCB
3 Nos. 16A SPN MCB c curve 10 KA

Note- Necessary wiring and interlocking for the above equipments shall
be done with the Fire Alarm system such that required fan gets actuated
and shut off the AHU in case of fire as per fire zones. No/NC contacts &
supply arrangements shall also be spared for the fire damper actuation &
control.

Supplying,Receiving, fixing, testing & commissioning of AHU Panel-2

(UGF/1F/2F/3F) as described above.Complete as required as per site Set 4 101737 406948
conditions.

44.0 NSR-31.0 AHU Panel-3 (Fourth Floor)

A INCOMER

1 No. 25A FP MCCB, 25 kA breaking capacity with thermal release and

adjustable setting and with rotary handle.

B METERING & INDICATION

1 Set - digital multifunction meter (showing harmonics along with all other
electrical parameters such as voltage current, Hz, KW, KWHr, PF.) with RS
485 port with matching cast resin CT's
1 Set - 0-500V 96 sqmm Voltmeter with selector switch, 3 No. phase indicating
LED lamp to show the incoming power with control SP MCB.
1Set of indicating LED lamps for MCCB On/Off with protective SP MCB's.

1 Set of CTs of the ratio 25/5A with class 0.5 Accuracy for Metering, burden 15
VA

C BUSBAR
32A TPN Aluminium Bar with colour coded PVC Sleeves

D OUTGOINGS
2 Nos. 16A TP MCB (including 1 no spare) with 1 No. 0.75HP DOL Starter (for
TFA unit)
BOQ HVAC Page 13 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)
5 Nos. 10A DP MCB
3 Nos. 16A SPN MCB c curve 10 KA

Note- Necessary wiring and interlocking for the above equipments shall
be done with the Fire Alarm system such that required fan gets actuated
and shut off the AHU in case of fire as per fire zones. No/NC contacts &
supply arrangements shall also be spared for the fire damper actuation &
control.

Supplying,Receiving, fixing, testing & commissioning of AHU Panel-3

(Fourth Floor) as described above.Complete as required as per site Set 1 101737 101737
conditions.

45.0 NSR-32.0 Kitchen Panel

A INCOMER

1 No. 32A FP MCCB, 25 kA breaking capacity with thermal release and

adjustable setting and with rotary handle.

B METERING & INDICATION

1 Set - digital multifunction meter (showing harmonics along with all other
electrical parameters such as voltage current, Hz, KW, KWHr, PF.) with RS
485 port with matching cast resin CT's
1 Set - 0-500V 96 sqmm Voltmeter with selector switch, 3 No. phase indicating
LED lamp to show the incoming power with control SP MCB.
1Set of indicating LED lamps for MCCB On/Off with protective SP MCB's.

1 Set of CTs of the ratio 32/5A with class 0.5 Accuracy for Metering, burden 15
VA

C BUSBAR
40A TPN Aluminium Bar with colour coded PVC Sleeves

D OUTGOINGS
2 Nos. 25A TP MCB (including 1 no spare) with 1 No. 5.0HP DOL Starter (for
scrubber)
2 Nos. 16A TP MCB (including 1 no spare) with 1 No. 3.0HP DOL Starter (for
air washer)
2 Nos. 16A DP MCB (including 1 no spare) with 1 No. 1.5HP DOL Starter (for
airwasher pump)
2 Nos. 10A TP MCB
3 Nos. 16A/25A SPN MCB c curve 10 KA

Supplying,Receiving, fixing, testing & commissioning of Kitchen Panel as

Set 1 88172 88172
described above.Complete as required as per site conditions.

46 NS-33 Isolator Switches With Metal Enclosure

46.1 NS-33.1 25A RCCB (300mA),4pole switch for VRV Outdoor units with sheet metal Each 1 3570 3570
enclosure, rain protection etc. as required to suit the site condition. (Enclosure
shall be suitable for out door installation.).Complete as required as per site
conditions.
46.2 NS-33.2 100A RCCB (300mA),4pole switch for VRV Outdoor units with sheet metal Each 3 6252 18756
enclosure, rain protection etc. as required to suit the site condition. (Enclosure
shall be suitable for out door installation.).Complete as required as per site
conditions.

47 NS-34 Cables form Air Conditioning Panel to each of ODUs

Supply, laying, Installation and Testing of the following sizes of PVC insulated
and FR PVC Round Sheathed, Copper Conductor (unarmoured) cable, 1100
Volt. Cables shall be inclusive of all clamps,saddles,screws,cable
identification tags, cable terminal joints including terminal lugs, insulating
tapes, affecting terminal connections to the equipment as per the
specifications and as required.Complete as required as per site conditions.
47.1 NS-34.1 4 C x 6 sq.mm Rmt 85 246 20910
BOQ HVAC Page 14 of 15
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Scheduled Non-Scheduled
DSR 2018- Rate(In
S.No. Description Unit Qty Item Item
2019/NSR Rs.)
(Amount Rs.) (Amount Rs.)

47.2 NS-34.2 4 C x 16 sq.mm Rmt 30 606 18180

47.3 NS-34.3 4 C x 35 sq.mm Rmt 110 1319 145090

48.0 NSR-35.0 MV Cable

Supply, laying & fixing of following sizes of PVC sheathed PVC/XLPE insulated
Aluminium conductor/copper conductor power/ multicore control armoured
cable of 1.1 KV grade.Complete as required as per site conditions.
48.1 NSR-35.1 4C- 6 sq mm Aluminium Metre 50 95 4750
48.2 NSR-35.2 4C- 4 sq mm Aluminium Metre 25 83 2075

49.0 4.1 MS Cable Trays

Supplying and installing following size of perforated painted with powder
coating M.S. cable trays with perforation not more than 17.5%, in convenient
sections, joined with connectors, suspended from the ceiling with M.S.
suspenders including bolts & nuts, painting suspenders etc. as required.

49.1 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Metre 20 476 9520
49.2 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 20 531 10620
49.3 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 20 621 12420

Total of Sub-Head 'D' - HVAC Electrical 32560 1354781

BOQ HVAC Page 15 of 15

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
PROJECT- : CONSTRUCTION OF OFFICE BUILDING FOR DENTAL COUNCIL OF INDIA
AT R.K PURAM NEW DELHI
BILL OF QUNATITIES FOR EXTERNAL ELECTRICAL WORKS
CPWD Amount Amount (Non
Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
Sub-Head - I : HT METER, TWO POLE STRUCTURE

1.0 NS-1 TWO POLE STRUCTURE (BEFORE METER ROOM)

Supply, erection and commissioning of 2 pole structure for terminating 11 KV O.H.
supply from State Electricity Boards as per specifications. The 2-pole structure
shall comprise of:
MS tubular swaged pole 11 mtrs high (410 SP 24 as per latest IS), in cement
concrete foundation 1:3:6 (1 cement : 3 coarse sand : 6 graded aggregate 40mm
nominal size) including excavation and refilling etc. as required. The rate shall be
inclusive of painting with 2 coats of aluminium paint (on zinc chromate). The portion
of pole under the ground shall be provided with 2 coats of bituminous paint - 2
Nos.

Steel sections, channels angles, flats, clamps, GI nuts, bolts and required hardware
etc of different sizes for cross arms, bracings, supports etc. for pole GOD etc.
including anticlimbing barbed wires (conforming to latest IS) having 4 points barbs
spaced 75 ±12mm apart. All steel structure shall be given 2 coats of zinc chromate
primer and 2 finishing coats of aluminium paint as required as per drawings and
direction of Engineer-in-Charge.

Supply,installation, testing and commissioning of 11 KV class disc/pin/support

insulators complete with clamps and fixing hardwares etc. complete as required as
per drawings and direction of Engineer-in-Charge.
Supply,installation, testing and commissioning of 11 KV station class thyrite type
lightning arrestors complete with mounting arrangement (on all phases) - 3 Nos.

Supply,installation, testing and commissioning of drop out - lock out (DOLO) fuse,
gang operating device (Air Break Switch) with pad locking arrangement (operating
rod to be supported properly), complete with operating handle at 1 mtr hight and
locking arrangement complete as required. Set-1 Nos.

Supply,installation, testing and commissioning of GI stay set complete with 20mm

dia 1.8 M long stay rod with 450 x 450 x 7.5 mm anchor plate with thimbles, stay
clamps, 7/4.00 mm dia GI stay wire, turn buckle (20mm x 600mm) strain insulator Set 1 155997 155997
bow tightner in cement concrete 1:3:6 foundation as excavation and refilling. Set-2
Nos.

2.0 NS-2 11 KV HT Metering Panel (SEB's) Indoor Type

The instrument and relay panel fitted with:
i) 1- digital voltmeter scaled 0-12000volt with 3 way and OFF selector switch.
ii) 1- digital Ammeter scaled 0-100 amps with 3 way and OFF selector switch.
1- Triple pole I.D.M.T. overcurrent & earth fault relay with two outer elements
connected for overcurrent protection and the middle element for earth fault
iii)
protection overcurrent, setting 50% - 200%, Earth fault setting 20% - 80% (51 and
51N).
1 No. SEB approved digital Trivector meter with MDI in KVA of accuracy class - 0.5.
iv) Note: The contractor shall get the Trivector meter , CTs' & PT tested by SEB.

v) One Set of Phase Indicating Lamps.

vi) 1- set of Red/Green indicating lamps for close and open position
vii) 1- Amber indicating lamp for auto trip
viii) 1- clear indicating lamp for trip circuit healthy
ix) 1- set of white indicating lamps one per phase
x) 1 - blue indicating lamp for spring charged
2 Nos. indoor cable end box suitable for 3C x 240 sq.mm. 11 KV(E), aluminium
xi) conductor XLPE Armourd cable (Incoming & Outgoing cable).

SITC Rate for Metering Panel as described above Set 1 155997 155997
Note:
1.The SITC rates of all components shall be considered.
2.The contractor shall ensure that the above panel meets the requirement as
insisted by local authorities/Electrical safety dept as well as the local
electricity supplier to meet satisfactory operation & maintenance and as per
the Drawings.

Total of Sub-Head - I carried to summary sheet 0 311994

Sub-Head - II - 11/.433 KV 500 KVA Compact Substation withTransformer

5.0 NS-4
(DRY TYPE)

BOQ for External Electrical Page 1 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
Supply, loading , unloading and installation testing and commissioning at site of
indoor type package substation with continuous rating 500 KVA transformer with
percentage impedance 5% (without negative tolerance) 11 KV 415V, 3 phase, 50
Hz delta/star connected, indoor,dry type cooper wound transformer, complete with
all fittings such as thermometers, OLTC with + 5 % to –15%, tapping at the step of
2.5%, RTCC bi-directional roller, diagrams & rating plate & Winding temperature
indicator, lifting lugs, H. T. Cable Box/ LT Cable Box suitable for Termination of
cables.Losses of transformer shall be as per specifications & conforming to ECBC
norms , complete with AVR & RTCC Panel. Compartment 4 mm thick base and 2
mm thick wall of each compartment with compartment, with IP 54 for HT & LT
compartment and IP 23 for transformer compartment, with naturally cooled type
canopy (Hot Galvanized Steel). foundation part for transformer not included in item,
to be taken from civil construction.

Package substation will have the following equipments-

Package substation will have the following equipments-
A RMU-NON-Extensible 1 WAY,11 KV , RN6C(1 isolators, 1 SF6 circuit breaker
along with connected accessories etc.),
TYPE:- Free standing, Metal Clad, SF6 insulated Ringmaster with 1 Nos 630A load
breaking, Fault Breaking Switches and 630A T off SF6 Circuit Breaker.

a) Self Powered Relay. Type IDMT

b) Ring switches and T OFF SF6 circuit breaker with Integrated Earthing Switches

c) Live Cable Indicator for Ring Switches- Provided

d) Padlocking Facility-Provided
e) Shunt trip coil rating- 230V AC.
f) Padlocking facility
All civil works such as PCC/RCC foudation, Platform, Fencing, Filling trench and
pedestals etc will remian in civil scope.

B) 11KV/433V, 500kVA three phase, Dyn11, ON load tap changer with +5% to –15
% in steps of 2.5% CU winding Dry type Transformer with standard
accessories.

C) LV Compartment:-
Outgoing:-
1No. 4 pole, 800A, 50KA MDO ACB.

Remote Tap Changer Control Panel (RTCC) comprise the following and as per
technical specifications:
Design, manufacture, supply, loading, unloading at site & site supervision of RTCC
panel, shall be of sheet steel cabinet for outdoor installation, floor mounting type.
The RTCC panel shall be 14 SWG CRCA sheet, totally enclosed, completely dust
and vermin proof and shall be with hinged doors, Neoprene gasket and padlocking
arrangement. The general construction shall confirm to IS-8623-1977 (part-I) for
factory built assembled switchgear & control gear for voltage up-to and including
1100 V AC.

The minimum but not limited to requirement of components to be provided in RTCC

panel shall be :
- Digital Tap Position Indicating Meter
- Raise/Lower Push Buttons for Remote Control of OLTC
- Tap Change in Progress Signal Lamp.
- Supply on Signal Lamp
- Local / Remote Control Indicating Lamps
- Panel illuminating lamp with door switch.
- Space Heater with Switch and Thermostat.
- Automatic Voltage Relay with Time Delay Element.
- Selectors switch for Auto/Manual Operation.
- Undrilled Gland Plate for Cable entry.
- Earthing Terminal
- Lifting Eyes Bolts.
500 KVA Compact Substation (as mentioned above) Each 1 2902904 2902904
Total of Sub-Head - II carried to summary sheet 0 2902904

6.0 NS-5 Sub-Head - III - D.G. SET WORK

BOQ for External Electrical Page 2 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
Supplying, loading, installation, testing & commissioning of Diesel Generating set
having Prime Power Rating of 400 KVA, radiator cooled type, with Acoustic
Enclosure with Silent Type silencer, 415 Volts at 1500 RPM, 0.8 lagging power
factor suitable for 50 Hz, 3 phase system and as per latest CPCB-II norms, inbuilt
fuel tank as per OEM standard. The DG Sets shall be suitable for being overloaded
6.1 5.1 upto 10% of the rated capacity for 1 hour in every 12 hours and consisting of the Sets 1 2919860 2919860
followings: The DG set shall be suitable for above 0.85 loading factor with net
output shall be 400 kVA as per site conditions with Genset governing Class G3 as
per IS 8528. Silent Diesel Genset shall be provided with remote monitoring system
to monitor the genset operational parameters at desktop/smartphones.

A. DIESEL ENGINE:
supply, instalation testing, commissioning of Diesel Engine 4 stroke water cooled,
electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at
40 Degree C, 50% RH & at 1000 MSL and conforming to BS 5514, BS 649, IS
10000, capable of taking 10% over loading for one hour after 12 hours of
continuous operation. The engine will be fitted complete with all the required
accessories.
Type: Radiator Cooled
Fuel injection :As per manufacturer
Engine Starting : Battery starting.
Starting position : Universal. Auto/Manual
The Engines shall include:
• Flywheel with guard.
• Flexible connection.
• Bellow / expansion joints
• Air Cleaner
• Blower fan
• Electronic governor with electronic fuel injection system
• Fuel and lube oil filters and pumps
• Day Fuel tank with visual level indicators etc.
• Silencer as per latest amendments of MOEF/CPCB
• Safety controls
• Instrument panel
• Exhaust piping to let out the exhaust at mandatory height above the canopy
including support arrangement and insulation with cladding inside the canopy etc.

B. ALTERNATOR;
Synchronous alternator rated at 400 KVA, 415 volts at 1500 RPM, 3 phase 50 HZ,
AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter
MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty,
self excited & self-regulated through suitable AVR conforming to site condition and
with Class-H insulation.
Type : Brushless.
Actual Power 400 KVA at 40 deg C.
Frequency : 50 Cycles/sec.
Supply System: 3 phases & neutral
Connection : Star.
Rated rpm. : 1500 RPM
Casing protection : As per IP-23
Insulation : Class H.
Power Factor : 0.8.
Controller : The DG sets should be suitable for Auto ON/OFF or equivalent
including providing of Engine control panel.

C. ACCESSORIES:
The Diesel Engine shall be equipped with minimum following/ as indicated in the
specifications, devices/ accessories built-in type including all standard fittings.

Fuel supply pump with manual venting pump.

Turbo charger with air filter (dry/oil bath type) and damper.
Charge air cooler.
Suction fuel filter
Lube oil filter.
Hour meter and RPM indicator.
Battery Starting Mechanism.
Instrument/Indication panel complete with the followings;
a) Starting Switch with key.
b) Lub. Oil Temp. gauge.
c) Lub. Oil Pressure Gauge.
d) Water Temp. gauge.
Control devices for safety and monitoring along with indicators.
Common base/foundation frame.
Anti vibration pads

BOQ for External Electrical Page 3 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
24V DC Starting system comprising of starter motors: Voltage regulator and
arrangement for initial excitation complete with suitable nos. of Maintenance free
batteries as per manufacturer standards for minimum 6 no. consecutive starts as
required as per specifications.
The cost of initial charge of lubricants, coolant etc.
The DG sets shall include the cost of all accessories, fittings, protections,
instruments, safety controls, alarms, indications etc. complete as per specifications,
as required

Supplying, loading, installation, testing & commissioning of Diesel Generating set

having Prime Power Rating of 200 KVA, radiator cooled type, with Acoustic
Enclosure with Silent Type silencer, 415 Volts at 1500 RPM, 0.8 lagging power
factor suitable for 50 Hz, 3 phase system and as per latest CPCB-II, inbuilt fuel
tank as per OEM standard. The DG Sets shall be suitable for being overloaded upto
6.1 5.2 10% of the rated capacity for 1 hour in every 12 hours and consisting of the Sets 1 1573537 1573537
followings: The DG set shall be suitable for above 0.85 loading factor with net
output shall be 200 kVA as per site conditions with Genset governing Class G3 as
per IS 8528. Silent Diesel Genset shall be provided with remote monitoring system
to monitor the genset operational parameters at desktop/smartphones.

A. DIESEL ENGINE:
Diesel Engine 4 stroke water cooled, electric start, of suitable BHP at 1500 RPM
suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 MSL and
conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for
one hour after 12 hours of continuous operation. The engine will be fitted complete
with all the required accessories.
Type: Radiator Cooled
Fuel injection :As per manufacturer
Engine Starting : Battery starting.
Starting position : Universal. Auto/Manual
The Engines shall include:
• Flywheel with guard.
• Flexible connection.
• Bellow / expansion joints
• Air Cleaner
• Blower fan
• Electronic governor with electronic fuel injection system
• Fuel and lube oil filters and pumps
• Day Fuel tank with visual level indicators etc.
• Silencer as per latest amendments of MOEF/CPCB
• Safety controls
• Instrument panel
• Exhaust piping to let out the exhaust at mandatory height above the canopy
including support arrangement and insulation with cladding inside the canopy etc.

B. ALTERNATOR;
Synchronous alternator rated at 200 KVA, 415 volts at 1500 RPM, 3 phase 50 HZ,
AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter
MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty,
self excited & self-regulated through suitable AVR conforming to site condition and
with Class-H insulation.
Type : Brushless.
Actual Power 200 KVA at 40 deg C.
Frequency : 50 Cycles/sec.
Supply System: 3 phases & neutral
Connection : Star.
Rated rpm. : 1500 RPM
Casing protection : As per IP-23
Insulation : Class H.
Power Factor : 0.8.
Controller : The DG sets should be suitable for Auto ON/OFF or equivalent
including providing of Engine control panel.

C. ACCESSORIES:
The Diesel Engine shall be equipped with minimum following/ as indicated in the
specifications, devices/ accessories built-in type including all standard fittings.

Fuel supply pump with manual venting pump.

Turbo charger with air filter (dry/oil bath type) and damper.
Charge air cooler.
Suction fuel filter
Lube oil filter.
Hour meter and RPM indicator.
Battery Starting Mechanism.

BOQ for External Electrical Page 4 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
Instrument/Indication panel complete with the followings;
a) Starting Switch with key.
b) Lub. Oil Temp. gauge.
c) Lub. Oil Pressure Gauge.
d) Water Temp. gauge.
Control devices for safety and monitoring along with indicators.
Common base/foundation frame.
Anti vibration pads
24V DC Starting system comprising of starter motors: Voltage regulator and
arrangement for initial excitation complete with suitable nos. of Maintenance free
batteries as per manufacturer standards for minimum 6 no. consecutive starts as
required as per specifications.
The cost of initial charge of lubricants, coolant etc.
The DG sets shall include the cost of all accessories, fittings, protections,
instruments, safety controls, alarms, indications etc. complete as per specifications,
as required

Total of Sub-Head - III carried to summary sheet 0 4493397

7.0 NS - 6 Sub-Head - IV- LT PANELS & DISTRIBUTION BOARDS

A. ALL LT PANELS SPECIFIC INCLUSIONS:
The outgoing feeders as indicated in SLD shall have suitable range of followings
(except capacitor feeders).
All ACB's shall be suitable for minimum 50 kA as specified in the items (Icu=Ics=Icw
for 1 sec.)
All MCCB's shall be suitable for unless otherwise specified in the item (Icu=Ics= 1
sec=100%.)
Wiring with space heater, thermostat and control MCB's shall be provided for all
vertical sections of main LT panel.
All incoming as well as outgoing feeders shall have pad locking facility.

Suitable danger board shall be provided.

All MCCB’s shall be provided with front rotary handle and operating mechanism for
door interlock with Pad locking of MCCB’s handles in “OFF” Position.

The Panel fabricator shall provide Al./ Copper Bus-bars link from Breakers
wherever more than two nos. of cables are terminated in the breakers.

All incoming and outgoing air circuit breakers shall be placed on middle portion of
the vertical in single tier formation.
All distribution sub panels shall be provided with class 1.0 accuracy meters as well
as CTs.
All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

Panels shall be Powder Coated with Siemens grey paint shade no. RAL-7032 of IS-
5.
All motor feeders MCCBs shall be of motor duty.
Supporting/Base rigid steel framework.
4P ACB’s / MCCB’s shall mean 4 pole ACB’s / MCCB’s with adequate size of
neutral link.

All MCCB having rating above 250A shall be microprocessor based.

B BACK ACCESS PANELS WITH ACB's

SITC, fabrication, assembly, wiring and supply, erection , testing and
commissioning of front operated dead front cubicle type compartmentalised as per
Form 3B, rear access free standing, dust and vermin proof (IP 43 ingress
protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz
system suitable for a symmetrical fault level of 25kA (specified with the panel) at
433 volts, fabricated from 2 mm outer thick CRCA MS sheets with hinged,
gasketted (metal based neoprene) and lockable doors having structural
reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland
plates on top and bottom and including lifting hooks and including earth strip of
required size with 2 nos. earthing terminals and including powder coated paint finish
of approved shade over metal surface cleaned and treated with nine tank process
complete with interconnections etc. as per specifications, as required and as below.
The incoming and outgoing feeders shall be accommodated in a modular
arrangement, detachable gland plates, adequate size cable alley, Sign writing,
Painting, Earthing, Numbering, Danger plate, including PVC insulated copper FRLS
wires of 2.5sq.mm for CT's etc. complete as required as per specifications and
drawing attached. A fairly uniform coating of 80 or better microns shall be provided.

(Note: The contractor may select the next higher fault rating of ACB/MCCB if it is
not readily available ,without any extra cost.)

BOQ for External Electrical Page 5 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs

7.1 NS-6.1 MAIN LT Panel

A INCOMER FROM 500 KVA CSS

1 Nos. of 800 A 4P electrically operated Drawout type ACB with Ics=Icu=Icw 50KA
having Mircroprocessor based releases for O/L, S/C & E/F.
1 Sets - digital multifunction meter (showing harmonics along with all other electrical
parameters such as voltage, current, Hz, KW, KWHr, PF.) with RS 485 port with
matching cast resin CT's
1 Sets - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED
lamp to show the incoming power with control SP MCB.
1 Sets indicating LED lamps for ACB On/Off/ Trip with protective SP MCB's.
1 Sets of CTs of the ratio 800/5A for APFC Relay, Burden 15 VA
1 Sets of CTs of the ratio 800/5A with class 0.5 Accuracy for Metering, burden 15
VA
1 No. 800/5A , 15 VA, 5P10 CT's for Protection
2 No. Under Voltage relay/Over Voltage Relay
Negative Phase protection Relay, reverse power relay

B INCOMER FROM 400 KVA D.G. SET-1

1 Nos. of 630 A 4P electrically operated Drawout type ACB with Ics=Icu=Icw 50KA
having Mircroprocessor based releases for O/L, S/C & E/F.
1 Set - Digital Multifunction Meter (showing harmonics along with all other electrical
parameters such as Voltage, current, Hz, KW, KVA, KVAR, KWh, PF.).

1 Set - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED
lamp to show the incoming power with control SP MCB.
3 nos. indicating LED lamps for On/Off/ Trip with protective SP MCB's.
1 Set of CTs of the ratio 600/5A with class 0.5 Accuracy for Metering, burden 15 VA

1 Set of. 600/5A , 15 VA, 5P10 CT's for Protection

2 No. Under Voltage relay/Over Voltage Relay

C INCOMER FROM 200 KVA DG ET-2

1 No. 400A 4P MCCB (36 KA) with electronic releases (O/C, S/C, E/F)
1 No. 400A 4P Contactor for E/M interlocking.
1 Set - Digital Multifunction Meter (showing harmonics along with all other electrical
parameters such as Voltage, current, Hz, KW, KVA, KVAR, KWh, PF.).

1 Set - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED
lamp to show the incoming power with control SP MCB.
3 nos. indicating LED lamps for On/Off/ Trip with protective SP MCB's.
1 Set of CTs of the ratio 400/5A with class 0.5 Accuracy for Metering, burden 15 VA

1 Set of. 400/5A , 15 VA, 5P10 CT's for Protection

D BUS BARS
Electrolytic high conductivity Aluminium three phase and neutral busbars with
earthing rated at 1000 amps having a maximum current density of 1 amp per sq
mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral
busbar is to be of 50% capacity.

E BUSCOUPLER
1 No. 400A 4P MCCB (36 KA) with electronic releases (O/C, S/C, E/F)
1 No. 400A 4P Contactor for E/M interlocking.

F OUTGOINGS-1
i) 1 Nos. 630A 4P MCCB (25 KA)
ii) 1 No. 400A 4P MCCB (36 KA)
ii) 4 No. 63A 4P MCCB (25 KA)
iii) 3 Nos. 80A 4P MCCB (25 KA)
iv) 1 Nos. 200A 4P MCCB (25 KA)

OUTGOINGS-2
i) 1 Nos. 100A 4P MCCB (25 KA)
ii) 2 Nos. 250A 4P MCCB (25 KA)
iii) 2 No. 63A 4P MCCB (36 KA)

BOQ for External Electrical Page 6 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
AUTO START / AUTO STOP,AUTO LOAD MANAGEMENT THROUGH PLC
G (AUTO WITH PCC-3.3 POWER COMMAND THROUGH DG SETS)

1 Set Micro PLC with IP / OP for control of (2 Nos. DG Sets and 1 No. CSS each
with PCC 3.3 POWER COMMAND / Equal. Micro PLC will also provide auto load
management system, inter- locking & auto change over.
MANUAL SYNCHRONISING
1 set Power Supply 10A, 24V DC with built in EMI filter
1 set Aux. / Control relays with 4 C/O , 24V DC
3 sets Emergency Stop push buttons (Mushroom type)
3 set Start / Stop push buttons
Lot - Indicating lights(LED TYPE)
1 No. ON LINE UPS with SMF Battery with suitable capacity
1 set Control relays 240 V AC
Lot - Control MCB 2A SP
Lot- Power MCB 16A /6A
Lot-Control terminals
3 Nos. Power Sockets 16A / 3 pin
2 Nos. selector switch 6A, Auto / Manual & DG selection (for 2 nos.
D.G. Sets)
1 No. DC supply healthy indicating light
1 No.DC Failure indicating light with alarm

Note: All outgoing breaker shall be provided with ON/OFF indicating Lamp.

Main LT Panel as described above Set 1 1383627 1383627

7.2 NS-6.2 Capacitor Panel (190 kVAR)

A INCOMER
1 No. 400A FP Microprocessor MCCB (25 KA) with Class-C transient voltage surge
suppression device suitable for 3 phases as per specifications.

B METERING & INDICATION

i) 1 set of phase indicating lamps
1 No. 10 step-Microprocessor APFC controller/Relay(Dual source purpose) shall
continuously monitoring all three phases and LCD displays for various Electrical
Parameters like voltage, input current, capacitive current, KVA demand, KW, Power
ii) Factor, self diagnostic error code indication with printout facility of the above with
RS 232/RS 485 port. Controller should mounted on the front side of the panel.
Capacitor bank having 3 phase MPP based mix dieelectric low loss ISI marked
power capacitor.

C BUS-BAR
1 Set of 500A TPN Aluminium Bus Bar with colour coded PVC Sleeves

D OUTGOINGS
i) 2 Nos.of 125A TP MCCB (25 KA) each with
2 Nos. 50 KVAR MPP Heavu Duty capacitor Bank each with capacitor duty
contactor.

ii) 2 Nos.of 80A TP MCCB (25 KA) each with

2 Nos. 25 KVAR MPP Heavu Duty capacitor Bank each with capacitor duty
contactor.

iii) 3 Nos. of 32A TP MCCB (25 KA) each with

3 Nos. 10 KVAR MPP Heavu Duty capacitor Bank each with capacitor duty
contactor.

iv) 2 No. of 25A TP MCCB (25 KA) each with

2 No. 5 KVAR MPP Heavu Duty capacitor Bank each with capacitor duty contactor.

Capacitor Panel (190 kVAR) as described above Set 1 386602 386602

B FRONT OPERATED PANEL

Design, manufacture, supplying fixing in position of the following front operated
cubicle type,compartmentalised with front access, dead back, 2mm thick steel
enclosed free standing, dust and vermin proof, switchboard with IP42 protection
with hinged and lockable doors complete with interconnections, tinned copper
crimping lugs, bonding to earth and painting, suitable for use at 415 volts, 3 phase 4
wire 50 Hertz system, and suitable for a fault level of 25 KA symmetrical at 415
volts.

All switchboards shall be modular type and have provision for entry of cables from
i
the top /bottom as required.

BOQ for External Electrical Page 7 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs

The cost shall include providing and fixing of 100 x 50 x 6 mm channels for
ii
switchboard support.

All live accessible parts shall be shrouded and all equipment shall be finger touch
iii proof. The Busbars insulation shall be with heat shrinkable sleeves. SMC/DMC
shrouds and busbar supports shall be used.

All MCCB shall have phase barriers, rotary handles and extension terminal as
iv
required .

All unbalanced kWH meter shall have communication module for BMS connectivity
v

NS-6.3 STILT FLOOR PANEL

A INCOMER
1 No. 63 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
i) 2 Nos. 25A 4P MCB (10 KA)
ii) 3 No.25A DP MCB (10 KA)
iii) 2 No.16A 4P MCB (10 KA)

Stilt Floor Panel as described above Set 1 56959 56959

NS-6.4 UPPER GROUND FLOOR PANEL

A INCOMER
1 No. 80 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
i) 1 Nos. 63A 4P MCB (10 KA)
ii) 2 No.40A DP MCB (10 KA)
iii) 2 No.25A DP MCB (10 KA)
Upper ground Floor Panel as described above Set 1 58899 58899

NS-6.5 FIRST FLOOR PANEL

A INCOMER
1 No. 63 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
ii) 3 No.40A 4P MCB (10 KA)
iii) 2 No.25A DP MCB (10 KA)

BOQ for External Electrical Page 8 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
First Floor Panel as described above Set 1 57950 57950

NS-6.6 SECOND FLOOR PANEL

A INCOMER
1 No. 63 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
ii) 3 No.40A 4P MCB (10 KA)
iii) 2 No.25A 4P MCB (10 KA)
Second Floor Panel as described above Set 1 58913 58913

NS-6.7 THIRD FLOOR PANEL

A INCOMER
1 No. 63 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
ii) 3 No.40A 4P MCB (10 KA)
iii) 2 No.25A DP MCB (10 KA)
Third Floor Panel as described above Set 1 57950 57950

NS-6.8 FOURTH FLOOR PANEL

A INCOMER
1 No. 80 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
ii) 2 No.63A 4P MCB (10 KA)
iii) 3 No.25A DP MCB (10 KA)
Fourth Floor Panel as described above Set 1 58207 58207

7.5 NS-6.9 TERRACE FLOOR PANEL

A INCOMER
1 No. 100 amps 4P MCCB(25 KA) with thermal Magnetic release with Class-C
transient voltage surge suppression device suitable for 3 phases as per
specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's.

BOQ for External Electrical Page 9 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
C BUS-BAR
i) 1 Set of 160A TPN Aluminium Bus Bar with colour coded PVC Sleeves.

D OUTGOINGS
i) 5 Nos. 40A 4P MCB (10 KA)
ii) 2 No. 32A DP MCB (10 KA)

Terrace Floor Panel as described above Set 1 82719 82719

7.6 NS-6.10 HVAC Panel

A INCOMER
1 No. 630 amps 4P Microprocessor MCCB(25 KA) with Class-C transient voltage
surge suppression device suitable for 3 phases as per specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

C BUS-BAR
i) 1 Set of 700A TPN Aluminium Bus Bar with colour coded PVC Sleeves

D OUTGOINGS
i) 2 Nos. 500A 4P MCCB (25 KA)
ii) 2 Nos. 40A 4P MCB (10 KA)
iii) 2 Nos. 63A 4P MCB (10 KA)

The Switchboard shall be complete with all interconnections, risers, internal wiring,
labels etc complete as required.
Fully automatic DOL starters (for 7.5 H.P.motors) with push buttons and on/off
indicating lights with MN type relay, contactors, direct type ammeter (0-40 A for
7.5 HP), single phase preventors for all motors, with selector switch and fuses
overload relay as required.
Fully automatic star-delta starters (for 12.5 H.P.motors) with push buttons and
on/off indicating lights with MN type relay, contactors, direct type ammeter (0-63 A
for 12.5 HP), single phase preventors for all motors, with selector switch and fuses
overload relay as required.
12.5 HP -2 No. DOL Starter
7.5 HP -2 Nos. Star Delta Starter
Spare N.O. - N.C. contacts for each starter - 3Set.
G.I. strip 25 x 3 mm throughout the length of MCC.
All internal wiring with colour coding from incoming mains to various switchgear,
starter, meter, indicating lamp and bus bar.
All starters shall be compatible for remote operation.All Switch gears offered must
be compatible with the H.P. of the motors offered

HVAC Panel as described above Set 1 316579 316579

7.6 NS-6.11 Lift Panel

A INCOMER
1 Nos. 63Amp FP ATS

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

C BUS-BAR
i) 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves

D OUTGOINGS
i) 3 Nos. 40A 4P RCBO
ii) 1 Nos. 40A 4P MCB (10 KA)

Lift Panel as described above Set 1 73929 73929

6.12 Pump Room Panel

A INCOMER
1No. 100A FP MCCB (25 KA) with thermal Magnetic release.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps with 3 Nos. 2A MCB.
ii) 1 No. Digital energy meter(Dual Source) with 3 nos. 100/5A CT's.

BOQ for External Electrical Page 10 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs

C BUS-BAR
i) 1 Set of 160A TPN Aluminium Bus Bar with colour coded PVC Sleeves

D OUTGOING
i) 2 Nos.40A 4P MCB(10KA).
ii) 16 Nos.32A 4P MCB(10KA).

The Switchboard shall be complete with all interconnections, risers, internal wiring,
labels etc complete as required.
Fully automatic DOL starters (for 0.5 to 7.5 H.P.motors) with push buttons and
on/off indicating lights with MN type relay, contactors, direct type ammeter (0-40A
for 0.5 to 7.5 HP), single phase preventors for all motors, with selector switch and
fuses overload relay as required.
1.0 HP -2 No. DOL Starter with sequence controller
1.5 HP -4 Nos. DOL Starter with sequence controller
2 HP -2 Nos. DOL Starter with sequence controller
2.5 HP -6 Nos. DOL Starter with sequence controller
7.5 HP -2 Nos. DOL Starter with sequence controller
Spare N.O. - N.C. contacts for each starter - 3Set.
G.I. strip 25 x 3 mm throughout the length of MCC.
All internal wiring with colour coding from incoming mains to various switchgear,
starter, meter, indicating lamp and bus bar.
All starters shall be compatible for remote operation.All Switch gears offered must
be compatible with the H.P. of the motors offered

Pump Room Panel as described above Each 1 4,18,669 418669

6.13 Fire fighting Panel

A INCOMER
1No. 250A FP MCCB (35 KA) with thermal Magnetic release.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps with 3 Nos. 2A MCB.
ii) 1 No. Digital energy meter(Dual Source) with 3 nos. 250/5A CT's.

C BUS-BAR
i) 1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves

D OUTGOING
i) 1 No. 160A 4P MCCB(25KA) for Electric Pumps.
ii) 1 No. 63A 4P MCCB(25KA) for Jckey Pump.
iii) 1 No. 100A 4P MCCB(25KA) for Terrace Fire Pump.
iv) 2 Nos.32A 4P MCB(10KA) .

The Switchboard shall be complete with all interconnections, risers, internal wiring,
labels etc complete as required.
Fully automatic DOL starters (for 2.5 H.P.motors) with push buttons and on/off
indicating lights with MN type relay, contactors, direct type ammeter (0-32A for 2.5
HP), single phase preventors for all motors, with selector switch and fuses overload
relay as required.
Fully automatic star delta starters (for 9 to 100 H.P.motors) with push buttons and
on/off indicating lights with MN type relay, contactors, direct type ammeter (0-
160A for 9 to 100 HP), single phase preventors for all motors, with selector switch
and fuses overload relay as required.
100 HP -1 No. Star Delta Starter
25 HP -1 No. Star Delta Starter
9 HP -1 No. Star Delta Starter
2.5 HP -1 No. DOL Starter
Spare N.O. - N.C. contacts for each starter - 3Set.
G.I. strip 25 x 3 mm throughout the length of MCC.
All internal wiring with colour coding from incoming mains to various switchgear,
starter, meter, indicating lamp and bus bar.
All starters shall be compatible for remote operation.All Switch gears offered must
be compatible with the H.P. of the motors offered

Firefighting Panel as described above Set 1 2,85,787 285787

6.14 UPS INPUT PANEL

A INCOMER
1 No. 250 amp ,4P ATS.

B METERING & INDICATION FOR INCOMER

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

BOQ for External Electrical Page 11 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's
iv) 1 Set of CTs of the ratio 250/5A with class 1.0 Accuracy for Metering, burden 15 VA

C BUSBAR
300A 4P Aluminium Bus Bar with colour coded PVC Sleeves

D OUTGOINGS
2 Nos. 160A 4P MCCB ,25 kA breaking capacity

UPS INPUT Panel as described above Set 1 196692 196692

6.15 UPS Output Panel

A INCOMER

2 Nos. 160 amps 4P MCCB(25 KA) with Class-C transient voltage surge
suppression device suitable for 3 phases as per specifications.

B METERING & INDICATION FOR INCOMER

i) 1 set of R,Y,B phase indicating lamps
ii) 1 No. (0-500V) digital Voltmeter with Built-in VSS with 3 nos. 2A SP MCB
1 No.- digital multifunction meter (showing electrical parameters such as voltage,
iii)
current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT's
iv) 1 Set of CTs of the ratio 160/5A with class 1.0 Accuracy for Metering, burden 15 VA

C BUSBAR
250A 4P Copper Bus Bar with colour coded PVC Sleeves

D OUTGOINGS
9 Nos. 25A DP MCB(10 kA)
1 Nos. 63A 4P MCB(10 kA)

UPS Output Panel as described above Set 1 115302 115302

Total of Sub-Head - IV carried to summary sheet 0 3608784

8.0 SUB HEAD- V : EARTHING

DSR-5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
8.2 arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt Each 16 6216 99456
as required.

DSR-5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
8.3 arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt Each 8 11794 94352
as required.

DSR-5.7 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for
8.4 conductor earth electrode, including connection/ termination with GI thimble etc. as Metre 150 44 6600
required.

DSR-5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe FRLSom
earth electrode including connection with brass nut, bolt, spring, washer excavation
8.5 and re-filling etc. as required. Metre 80 1224 97920

DSR-5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth
electrode including connection with G.I. nut, bolt, spring, washer excavation and re- Metre 300 483 144900
filling etc. as required.
8.6
DSR-5.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I.
Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. Metre 50 188 9400
thimble excavation and re-filling as required.
8.7
DSR-5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for
Metre 200 1009 201800
connections etc. as required.
8.8
DSR-5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for
Metre 500 206 103000
connections etc. as required.
8.9
DSR-5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as
Metre 150 57 8550
required.

BOQ for External Electrical Page 12 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs

Total of Sub-Head - V carried to summary sheet 572170 193808

9.0 SUB HEAD-VI : CABLE & END TERMINATIONS

Laying and fixing of one number PVC insulated and PVC

DSR 2018-
sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as
7.8
required.
Upto 35 sq. mm (clamped with 1mm thick saddle)
DSR 2018-
9.1 Metre 310 33 10230
7.8.1

DSR 2018- Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
9.2 Metre 15 74 1110
7.8.2 MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with

DSR 2018-
9.3 25/40x3mm MS flat clamp) Metre 280 93 26040
7.8.3

Above 185 sq. mm and upto 400 sq. mm (clamped with

DSR 2018-
9.4 40x3mm MS flat clamp) Metre 330 150 49500
7.8.4

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate
DSR 2018- with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60
9.5 cm long and fixing the same in ground as required. Each 10 383 3830
7.10

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11
DSR 2018-
9.6 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required.
8.3
Above 120 sq. mm and upto 400 sq. mm
DSR 2018-
9.7 Metre 100 112 11200
8.3.2

Supplying and making end termination with brass compression gland and
DSR 2018- aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE
9.8
9.1 aluminium conductor cable of 1.1kV grade as required.

9.8.1 9.1.26 3½ X 150 sq. mm (50mm) Each 6 555 3330

9.8.2 9.1.30 3½ X 300 sq. mm (70mm) Each 18 936 16848
9.8.3 NS 4 X 6 sq. mm (25mm) Each 10 185 1850
9.1.25 3½ X 120 sq. mm (45mm) Each 2 489 978
9.8.11 9.1.33 4 X 16 sq. mm (28mm) Each 8 250 2000
9.1.34 4 X 25 sq. mm (28mm) Each 2 250 500
9.1.29 3½ X 240 sq. mm (62mm) Each 4 809 3236
9.1.21 3½ X 35 sq. mm (32mm) Each 4 300 1200

HT CABLE END TERMINATION

Supplying and making indoor cable end termination with heat shrinkable jointing kit
DSR 2018- complete with all accessories including lugs suitable for following size of 3 core,
10.0
10.4.3 XLPE aluminium conductor cable of 11 kV grade as required.

10.1 240 sq. mm Each 2 11681 23362

Supplying and making outdoor cable end termination with heat shrinkable jointing
DSR 2018-
11.0 kit complete with all accessories including lugs suitable for following size of 3 core,
10.5.3
XLPE aluminium conductor cable of 11 kV grade as required.
11.1 240 sq. mm Each 2 17166 34332

NS-7 Supply of HT cable

Supplying of following sizes of XLPE aluminium conductor, corss linked polythylene,
individual core screwed, flat steel strip armoured, PVC sheathed cable of 11KV
12.0
grade (earthed) comforming to IS: 7098 (Part 2),with uptodate ammendment
complete as required.
12.1 3 C x 240 Sq.mm XLPE HT cable (Earthed) Metre 50 1051 52545

NS-8 Supply of MV cable

Supply, following sizes of PVC sheathed PVC/XLPE insulated Aluminium
13.0 conductor/copper conductor power/ multicore control armoured cable of 1.1 KV
grade.
13.1 NS-8.1 3 ½ C - 300 sq mm Aluminium Metre 330 1156 381478
13.2 NS-8.2 3 ½ C - 150 sq mm Aluminium Metre 120 646 77480
13.3 NS-8.3 3 ½ C - 240 sq mm Aluminium Metre 100 947 94740
13.4 NS-8.4 3 ½ C - 120 sq mm Aluminium Metre 60 467 27992
13.5 NS-8.5 3 ½ C - 35 sq mm Aluminium Metre 65 190 12368

BOQ for External Electrical Page 13 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
13.6 NS-8.6 4C- 16 sq mm Aluminium Metre 90 127 11393
13.7 NS-8.7 4C- 6 sq mm Aluminium Metre 90 89 8025
13.8 NS-8.8 4C- 25 sq mm Aluminium Metre 65 40 2600
Total of Sub-Head - VI carried to summary sheet 187696 670472

14.0 NS-9 SUB HEAD- VII : EXTERNAL LIGHTING & LANDSCAPE LIGHTING WORK
The rates for fixing of lighting fixtures shall include all fixing accessories that may be
required to make the installation complete in all respects .
Internal wiring between accessories connecting wires wherever required.

6-9 W LED Bollard Light .Pressure die cast aluminium painted housing with Diffuser
made of Polycarbonate ,symmetrical wide light distribution Ingress Protection rating
IP66. All luminaires shall be with associated driver , lamp and other connecting or
9.1 Each 10 4703 47032.45386
mounting accessories to make it complete in all respect for operational purpose.
The supplier shall submit the technical specification sheets alongwith LM reports for
approval.

45W LED Post Top luminaire. Pressure die cast aluminium housing with Luminaire
cover made of Polycarbonate/PMMA ,symmetrical wide light distribution & Ingress
Protection rating IP66. All luminaires shall be with associated driver , lamp and
9.2 Each 3 12094 36282.17869
other connecting or mounting accessories to make it complete in all respect for
operational purpose. The supplier shall submit the technical specification sheets
alongwith LM reports for approval.

70 - 80W LED floolight luminaire for building highlighter. Pressure die cast
aluminium housing with Luminaire cover made of Polycarbonate/PMMA
,symmetrical wide light distribution & Ingress Protection rating IP66. All luminaires
9.3 shall be with associated driver , lamp and other connecting or mounting accessories Each 6 6450 38700.9906
to make it complete in all respect for operational purpose. The supplier shall submit
the technical specification sheets alongwith LM reports for approval.

6.0 meter high G.I octagonal pole (Above Ground Level) with single arm of suitable
length with inbuilt junction box with 10A SP MCB, connectors for incoming/outgoing
cable connection and 300mm x 300mm x 20 mm thick base plate including earthing
stud, foundation base plate 20mm thick, complete in all respect including CC
foundation minimum size 350mm x350mmx500mm with provision of PVC pipe for
9.4 UG cable entry & termination of cable with gland/ thimble including 4 Nos. heavy Each 6 15050 90302.31141
duty foundation nut bolts with suitable length complete as required including
erection of G.I. pole in 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded
stone aggregate 40mm nominal size) including excavation & refilling etc as required
below ground complete as per requirement with all accessories.

40W Smart integrated solar street light with all in one Hybrid with system with built
in Mono Crystalline panel, Lithium ferro phospate (Life PO 4) battery, MPPT charge
9.5 Each 6 79955 479731.0294
controller and PIR Sensr with colour temperature 6000-6500K.

Total of Sub-Head - VII carried to summary sheet 0 692049

16 NS-11 Sub-Head - VIII- PASSANGER ELEVATOR

BOQ for External Electrical Page 14 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
Supply, Installation, Testing and Commissioning of 13 Passanger Elevator, Machine
room less in lift shaft of dimensions 1800mm x1900mm (W x D), 884 Kg., with
variable voltage variable frequency drive having a speed of 1.5 metre/ sec and
travel height of 30 m(approx.) with 9 Stops and Microprocessor based control
suitable for operation on 415 V, 50 Hz, 3 phase A.C. electric Supplying as required.
1.Type of machine Gearless,MRL
2.Capacity 884kg
3.Speed 1.5 mps.
4.No of landing 9 Landings(2 Basement, S+UG+5)
5.Number of openings 9 on the same side.
6.Travel approx 30meter
7.Power Supplying 415v/240v, 50HZ
8.Acceptable voltage Fluctuation +10 to -20%
16.1 11.1 9.Rate of Accelaration / 0.6-1.5 (adjustable at site) Each 3 1770733 5312199.907
decelration (m/sec.sq)

10.Jerk (m/sec.sq) 0.7-1.5 (adjustable at site)

11.Vibration in car horizontal 20/18 MG maximum
vertical 20/18MG maximum
12.Noise level in car 48dbA max.
13.Noise level in machine room 62dbA max.
at 1m from machine
14. Door noise level while closing and 52dbA max. opening at a distance of 1mtr.
from car door and 1.5 mtr. from floor level.

.
Total of Sub-Head - VIII carried to summary sheet 0 5312199.907

17 NS-12 Sub-Head -XI : LINEAR PNUEMATIC HEAT DETECTION TUBE SYSTEM

Supply, Installation, Testing and Commissioning of 2.5 LB capacity Novec 1230 ,
DLP Assembly with automatic valve, push in connector for tube, 2.5 LB Novec 1230
17.1 12.1 No. 1 101737 101737.29
gas , mounting bracket, End of Line adopter and low pressure switch for monitoring
system activation.

Supply, Installation, Testing and Commissioning of 5 LB capacity Novec 1230 , DLP

Assembly with automatic valve, push in connector for tube, 5 LB Novec 1230 gas ,
17.2 12.2 No. 1 149215 149214.692
mounting bracket, End of Line adopter and low pressure switch for monitoring
system activation.

Supply, Installation, Testing and Commissioning of 10 LB capacity Novec 1230 ,

DLP Assembly with automatic valve, push in connector for tube, 10 LB Novec 1230
17.3 12.3 No. 1 250952 250951.982
gas , mounting bracket, End of Line adopter and low pressure switch for monitoring
system activation.

Supply, Installation, Testing and Commissioning of Linear pneumatic heat Detection

17.4 12.4 mtrs. 150 2713 406949.16
Tube with all necessary fittings & supports.

Supply, Installation, Testing and Commissioning of Master Control Unit with Audio
Visual Alarm with wiring to make complete system operational . The control Panel
17.5 12.5 Nos 5 6104 30521.187
should have provision for integration with fire Alarm /SCAD/BMS System.

Total of Sub-Head - IX carried to summary sheet 0 939374.311

17 NS-13 Sub-Head -X : BOOM BARRIER SYSTEM

Supply, Installation , Testing and Commissioning of High Speed Microprocessor
based with activation system comprising Electro-Mechanical pump unit ,
balancing by compression spring , internal stops adjustable for open or close
17.1 13.1 Nos. 1 149215 149214.692
beam positions . the barrier for continuous use for vechicular span of up to 6 mtrs,
includes Boom with controller & accessories , 100% duty cycle. with complete as
required

Supply, Installation, Testing and Commissioning of Twin Channel Exit Push putton
17.2 13.2 Nos. 1 4883 4883.38992
for open close with green and red Buttons.

Supply, Installation, Testing and Commissioning of Photocell based safety device to

17.3 13.3 Set 1 6986 6985.96058
avoid closing of the barrier when a Vehicle is crossing the barrier.

Supply, Installation, Testing and Commissioning of 3 x 1.5 sq. mm diameter, copper

17.4 13.4 Metre 100 38 3798.19216
conductor PVC cable in existing Conduit complete as required.

Supply, Installation, Testing and Commissioning of Connectors, interfaces,

17.5 13.5 Mounting hardware, Cords, Jacks, Plugs, tags, identifiers, fixures, clamps, screws, Set 1 71623 71623.05216
nut - bolts etc as required for the installation and commissioning.

BOQ for External Electrical Page 15 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD Amount Amount (Non

Sr.
DSR 2018 Description Unit Qty. Rate (Schedule Schedule
No.
Item no Items) Rs Items) Rs
Supplying and fixing of following sizes of medium class PVC conduit along with
17.6 1.21 accessories in surface/recess including cutting the wall and making good the same
in case of recessed conduit as required.
1.21.2 25 mm Metre 100 90 9000

Total of Sub-Head - X carried to summary sheet 9000 236505.2868

BOQ for External Electrical Page 16 of 16

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CONSTRUCTION OF OFFICE BUILDING FOR DENTAL COUNCIL OF INDIA

AT R.K PURAM NEW DELHI
BILL OF QUNATITIES FOR INTERNAL ELECTRICAL WORKS
Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs

INTERNAL ELECTRICAL WORK

1.0 1 SUB HEAD-1: WIRING & SUBMAIN
1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS
PVC insulated copper conductor single core cable in surface / recessed medium class
PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point Each
with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable etc. as required.
1.10.3 Group C 495 990 490050

1.54 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point
(without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper
2.0 conductor single core cable in surface/ recessed steel conduit, and earthing the point
with 1.5 sq. mm FRLS PVC insulated
copper conductor single core cable etc. as required.
2.1 1.54.3 Group C Each 218 707 154126

NS-1.1 Wiring for the MCB controlled Primary light points with 2.5 sq.mm PVC insulated
copper conductor 1100 volts grade stranded flexible FRLS wires of approved make in
3.0 concealed or surface mounted 25 mm dia 2.0 mm thick PVC conduit but controlled by Each 4 1097 4388
existing MCB provided in D.B. including earthing of fixtures with 2.5 sq.mm insulated
copper wire.

1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor
single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq.
4.0 Metre 1000 200 200000
mm FRLS PVC insulated copper conductor single core cable for loop earthing as
required.

1.13 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor
single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4
5.0 Metre 800 308 246400
sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as
required.

1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS
6.0 PVC insulated copper conductor, single core cable in surface/ recessed medium class
PVC conduit as required.
1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (For Circuit Wiring & Light Plug Wiring)
6.1 Metre 1500 167 250500
1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire (For Single Phase DB. From Sub Panel to
6.2 Metre 400 249 99600
DB)
1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire (For Three Phase DB. From Sub Panel to DB)
6.3 Metre 2 394 788
1.14.10 4 X 10 sq. mm + 2 X 10 sq. mm earth wire (For Three Phase DB. From Sub Panel to
6.4 Metre 543 0
DB)
1.14.11 4 X 16 sq. mm + 2 X 16 sq. mm earth wire (For Three Phase DB. From Sub Panel to
6.5 Metre 200 752 150400
DB)

1.25 Supplying and fixing stepped type electronic fan regulator on the existing modular
7.0 plate switch box including connections but excluding modular plate etc. as required. Each 14 342 4788

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch
8.0 Each 10 32 320
box excluding modular plate as required.

NS-1.3 Supplying and fixing suitable size GI box with modular plate
and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A
9.0 Each 450 1031 463950
modular socket outlet and 5/6 A modular switch, connections etc. as required.

NS-1.4 Supplying and fixing suitable size GI box with modular plate and cover in front on
surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular
10.0 Each 94 1208 113552
socket outlet and 15/16 A modular switch, connections etc. as required.

1.50 Installation of exhaust fan in the existing opening, including making good the damage,
11.0
connection, testing, commissioning etc. as required.
11.1 1.50.1 Upto 450 mm sweep Each 32 363 11616

1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
12.0 Each 32 168 5376

Total of Sub-Head - I carried to summary sheet 1613964 581890

13.0 2.00 SUB HEAD -II : DISTRIBUTION BOARD

2.30 Supply and fixing following way, single pole and neutral, sheet steel, MCB distribution
board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar,
14.0
earth bar, din bar, interconnections, powder painted including earthing etc. as required.
(But without MCB/RCCB/Isolator).
14.1 2.3.1 6 way, Double door Each 5 1661 8305
14.2 2.3.2 8 way, Double door Each 8 1760 14080

BOQ for Internal Electrification Work Page 1 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
14.3 2.3.3 12 way, Double door Each 9 2053 18477

BOQ for Internal Electrification Work Page 2 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
2.40 Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet
for 415 volts on surface/ recess complete with loose wire box, terminal connectors for
all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated
15.0 copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar,
din bar, detachable gland plate, interconnections, powder painted including earthing etc.
as required.(But without MCB/ RCCB/ Isolator).

15.1 2.4.3 8 way , Double door Each 5 4601 32207

15.2 NS-1.5 12 way, Double door Each 7 12694 88857

2.50 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V,
TPN MCB distribution board of sheet steel, dust protected, duly powder painted,
inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for
16.0 mounting MCBs (but without MCBs and incomer ) as required .
(Note : Vertical type MCB where 3 phase outlets are required.) TPDB is normally used

16.1 2.5.1 4 way (4 + 12), Double door Each 7 5651 39557

2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature
circuit breaker suitable for inductive load of following poles in the existing MCB DB
17.0
complete with connections, testing and commissioning etc. as required.

17.1 2.10.1 Single pole Each 454 199 90346

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as
18.0 Each 41 8 328
required.

NS-2 Supplying and fixing following rating, double pole, 240 volts, MCB in the existing MCB
19.0 DB complete with connections, testing and commissioning etc. as required.

19.1 NS-2.1 25 amps Each 7 946 6623

NS-3 Supplying and fixing following rating, four pole, 415 volts, MCB in the existing MCB DB
20.0 complete with connections, testing and commissioning etc. as required.

20.2 NS-3.1 40 amps Each 1 2055 2055

20.3 NS-3.2 63 amps Each 7 2055 14387

2.14 Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,
residual current circuit breaker (RCCB), having a sensitivity current upto 300
21.0
milliamperes in the existing MCB DB complete with connections, testing and
commissioning etc. as required.
21.1 2.14.1 25 amps Each 21 1927 40467

BOQ for Internal Electrification Work Page 3 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
21.2 2.14.2 40 amps Each 3 2095 6285
21.3 2.14.3 63 amps Each 21 2640 55440

2.17 Supplying and fixing TP sheet steel enclosure on surface/ recess along with
22.0 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and Each 2 1146 2292
commissioning etc. as required.

2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole
and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet
23.0 steel enclosure, on surface or in recess, with chained metal cover for the socket out let Each 4 1232 4928
and complete with connections, testing and commissioning etc. as required.

2.19 Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole
and earth, metal enclosed plug top alongwith 20 amps "C" curve, TPMCB, in sheet
24.0 steel enclosure, on surface or in recess, with chained metal cover for the socket out let Each 4 1690 6760
and complete with connections, testing and commissioning etc. as required.

2.20 Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole
and earth, metal enclosed plug top alongwith 30 amps “C” curve, TPMCB, in sheet
25.0 steel enclosure, on surface or in recess, with chained metal cover for the socket out let Each 5 3048 15240
and complete with connections, testing and commissioning etc. as required.

Total of Sub-Head - II carried to summary sheet 334712 111923

26.0 SUB HEAD - III : LIGHTING FIXTURE & FAN

1.35 Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and
27.0 shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all Each 716 98 70168
accessories including connections etc. as required.

28.0 NS-4 Supply of Light fixture as given below

Supplying of All Lights fixtures shall be complete with LED lamps with all required
accessories.Samples of all the fixtures with all available colour shall be submitted to the
architect/ client/ Project Manager before supply & approval is taken.
Please check the fixtures final quantity from the Architect / Project Manager before
ordering and be sure of actual requirement prior to ordering.

BOQ for Internal Electrification Work Page 4 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
4.1 Supply of recess mounting 6 W LED down light with 50000 burning hours high efficient
LED’s, CCT-5700-6500 K,CRI >80, Lumens ≥ 80lumen/watt, single piece pressure die
cast powder coated housing with opal diffuser for glare free & uniform lighting, Driver
shall be of constant current type, operating temperature from -10 to +45degree celcius,
28.1 Each 60 723 43390
power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz
+_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the
entire satisfaction of Engineer-in-Charge.

4.2 Supply of surface mounting 15 W LED down light with high efficient LED’s,with 50000
burning hours CCT-5700-6500 K,CRI >80, Lumens ≥ 1500, white powder coated
aluminium housing with opal diffuser for glare free & uniform lighting, Driver shall be of
constant current type, operating temperature from -10 to +45 degree celcius, power
28.2 Each 36 1718 61860
factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%,
AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire
satisfaction of Engineer-in-Charge.

4.3 Supply & erection of 20 watt LED Tube Light rod, 4' long suitable with 40000 burning
hours for rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC
supply with aluminium alloy base,, frosted polycarbonate diffusers with power factor
>0.90, Total Harmonic Distortion (THD) < 20%, system current - 0.085A, system
efficiency > 85% , with operating temp. -10° C to 45° C, Lumen output for LED tube
should be > 2000 lumen and overall lumen/watt of luminaire should be greater than
28.3 80%, C.R.I. of LED>80% with correlated colour temperature (CCT) of 6500K , Each 89 677 60228
minimum burning hour life >40000 hours,LED viewing angle 120 Degree complete in all
respect with the entire satisfaction of the Engineer-in-incharge. Supply of Industrial
General Purpose 4' long tube fitting suitable to house 1x20w LED tube rod 4' long,
Polycarbonate housing , rated voltage 240 V and Ingress protection IP-20 complete in
all respect with the entire satisfaction of the Engineer-in-incharge.

4.4 Supply of 9 W mirror light with high efficient LED’s, CCT-6500 K,CRI >70, Lumens
≥900, with Ingress protection IP-20, with 50000 burning hours Driver shall be of
constant current type, operating temperature from -10 to +45 degree celcius, power
28.4 Each 25 478 11942
factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%,
AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire
satisfaction of Engineer-in-Charge.

4.5 Supply of 10W surface mounted LED Bulk Head Light with ABS body & Polycarbonate
diffuser, with 50000 burning hours , CCT-5700- 6000 K,CRI >70, Lumens ≥1000, with
Ingress protection IP-66, Driver shall be of constant current type, operating
28.5 temperature from -10 to +45 degree celcius, power factor>0.90, rated voltage 220- Each 39 1300 50714
240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection -
Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

4.6 Supply of 15W LED decorative wall scone light with 50000 burning hours stainless stell
28.6 Each 20 2256 45115
base, frosted glass diffuser.

4.7 Supply of 10W single LED aviation light luminaire with 50000 burning hours minimum
system efficiancy of 100 lm/W with Die-cast aluminum housing with Red polycarbonate
dome for better illumination, with minimum system efficacy of 100 lm/W. Nominal Input
28.7 Each 2 4060 8121
Power 10 W, & CRI >80, minimum burning hour life >50000 hours builtinsurge
protection.

4.8 Supply of LED exit signage of Box size in mm 325x425x365 with 50000 burning hours.
28.8 Each 10 4777 47768

4.9 Supply of 1200mm ceiling fans complete with double ball bearing, motor, blades,
canopies, capacitor etc. suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply
with 5 star rating complete as required. ceiling fan, including wiring the down rods of
28.9 standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, Each 14 1962 27475
single core cable, including providing and fixing phenolic laminated sheet cover on the
fan box etc. as required.

4.10 Supplying of Plastic Body Ornamental Exhaust Fan heavy duty 230V A.C 50 cycles,
28.10 300 mm sweep, 1300 rpm, energy efficient, complete erected in position with all Each 32 1576 50443
accessories.

4.11 Supply of recess mounting 18 W LED down light with 50000 burning hours. high
efficient LED’s, CCT-5700k -500 K,CRI >80, Lumens ≥ 1800, single piece pressure die
cast powder coated housing with opal diffuser for glare free & uniform lighting, Driver
shall be of constant current type, operating temperature from -10 to +45degree celcius,
28.11 Each 105 1035 108673
power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz
+_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the
entire satisfaction of Engineer-in-Charge.

BOQ for Internal Electrification Work Page 5 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
4.12 Supply of 36 W recess mounted LED back-lit 2’x2’ with high efficient LED’s, CCT 5700
- 6500 K,CRI≥80, System lumen 100lm/W, Lumens ≥ 3600, white powder coated
CRCA with PMMA opal diffuser for glare free & uniform lighting, minimum burning hour
life >50000 hours. Driver shall be of constant current type, operating temperature from -
Each 242 1712 414231
10 to +45 degree celcius, power factor>0.95, rated voltage 220-240V AC working
range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV.
Complete in all respect with the entire satisfaction of Engineer-in-Charge.

4.13 Supply of 18W Hanging light with 50000 burning hours Each 42 1353 56844

Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology

based occupancy sensor having high preformance, non regulating programmable type,
DSR-15.1 suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m Each 29 4538 131602
diameter coverage area along with necessary fixing arrangements i/c programming at
site etc. complete as required.

Total of Sub-Head - III carried to summary sheet 201770 986803

29.0 SUB HEAD- IV : LIGHTNING PROTECTION SYSTEM

Supplying, installation, testing & commissioning of long life Maintenance Free
Earthing System. The Rod shall be of Copper Bonded Steel with 17.2 mm dia. and 10
feet length with a core of mild steel molecularly bonded with min. 250 microns coating
of 99.99% pure electrolytic grade Copper , UL Listed , tested by CPRI capable of
29.1 NS-5 Each 8 9599 76793
bearing fault current of 25 kA. Along with earth enhancement compound tested by
RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3)
resistivity is less than 0.12 ohm meter . with Suitable Poly-plastic Pit Cover with
lockable arrangement.

6.20 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I.
29.2 tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including Each 6 304 1824
holes etc. complete as required.

6.70 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for
29.3 Mts. 500 66 33000
lightning conductor complete as required.(For horizontal run)

6.80 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for
29.4 Mts. 200 100 20000
lightning conductor complete as required.(For vertical run)

6.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm
29.5 long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as each 30 73 2190
required.

6.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as
29.6 Mts. 100 112 11200
required.

Total of Sub-Head - IV carried to summary sheet 68214 76793

30.0 SUB HEAD - V : TV, DATA, VOICE NETWORKING

1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor
PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in
Metre 150 33 4950
the existing surface/ recessed steel/ PVC conduit as required.

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with
40.0 accessories in surface/recess including cutting the wall and making good the same in
case of recessed conduit as required.
40.1 1.21.2 25 mm Metre 7920 90 712800

1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover
32.0
plate for modular switches in recess etc.as required.
32.1 1.27.1 1 or 2 Module (75mmX75mm) Each 265 243 64395

1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/
34.0
recessed Steel/ PVC conduit as required.
34.1 1.53.1 1 run of cable Metre 7770 49 380730

NS-6 Supplying & Fixing of Non- PCB based Information Outlet (I/O) RJ45, Tolless
Termination TIA-568C Category-6, Termination of Catergory-6 UTP Cable, UL listed
,Shall conform to Category-6 as per the EIA/TIA-568C.2,Shall support network line
speeds up to 1 Gbps, Shall have RJ-45 type connector with bend limiting and strain
33.0 relief boot for securing IDC contacts from external forces and for maintaining the bend Nos. 259 343 88791
radius of the cable, Shall have minimum duraility of 950 or Above mating cycles and
200 termination cycles. Certified by independent labs like ETL/GHMT/3P for
compliance to EIA/TIA-568C.2 complete in all respect.

BOQ for Internal Electrification Work Page 6 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
NS-7 Supply,installation, testing & commissioning of UTP Jack Panel, loaded with 24 nos
UTP ports for IO Jacks (RJ45, TIA-568C Category-6, Shall have integrated bonding
bar or other mechanism for grounding, Shall be loaded with individually replaceable 24
nos. Category-6 certification by Jacks complying with TIA-568.C.2 , Shall be having a 6
36.0 Nos. 12 11656 139872
port module construction for better cable dressing at the rear, the jacks shall have RJ-
45 type connector with bend limiting and strain relief boot for securing IDC contacts
from external forces and for maintaining the bend radius of the cable complete in all
respect.

NS-8 Supplying & Fixing of Category 6, UTP patch cords shall be constructed of 24-27 AWG
unshielded twisted pair stranded copper cable with an enhanced performance modular
plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for
37.0 Nos. 259 274 71033
design flexibility with a clear strain relief boot on each modular plug. All patch cords
shall be compatible with both T568A and T568B wiring schemes. UTP Cable will be
1.0 mtr. complete in all respect.

NS-9 Supplying & Fixing of Category 6 UTP patch cords shall be constructed of 24-27 AWG
unshielded twisted pair stranded copper cable with an enhanced performance modular
plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for
38.0 Nos. 259 377 97671
design flexibility with a clear strain relief boot on each modular plug. All patch cords
shall be compatible with both T568A and T568B wiring schemes. Blue UTP Cable, 2
Meter complete in all respect.

NS-10 Supplying, Installation, Testing & Commissioning of 50μ, 6-core Multi mode OM3
metallic armored Fiber cable as per ISO/IEC-11801, Shall be able to meet Gigabit & 10
Gigabit Ethernet performance up to 300 meters requirement specified by IEEE 802.3z
(1000 Base-X) & IEEE 802.3ae (10G Base-X) Tensile load should be 4000 Newton or
higher and crush resistance should be 4000 Newton or higher ,The attenuation @ 850
39.0 RM 100 343 34282
nm should be ≤ 2.7 (Max) db/Km and @ 1300 nm should be ≤ 0.7 (Max) dB/Km, the
fiber construction can be unitube or multitube, but tensile and crush resistance
parameters should be matched, the jacket shall be FRLSZH complete in all respect.

NS-11 Supplying & Fixing of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack
Mount ,Shall have all accessories including coupler plates pre loaded with 12 Nos of
40.0 Nos. 2 21666 43333
LC couplers (OM3) with all accessories complete in all respect. Pigtails Should Complie
to ITU-G657.B-Bend insestive fiber.

NS-12 Supplying & Fixing of Fiber Optic Patch Cable (LC-LC), 3 Mtrs. Long, ISO/IEC-11801-
OM3 50μ Duplex, LSZH,All patch cords shall conform to EIA/TIA-568C.3 and ISO/IEC-
41.0 11801,Shall be Duplex Multi Mode Fiber Optic Patch Cords OM3 50μ,Shall support Nos. 4 2057 8228
network line speeds up to 10 Gbps.Shall have LC-LC Connector connectors at the
ends complete in all respect.

NS-13 Supply, installation, testing & commissioning of OM3 50/125μ Type Pigtails of ISO/IEC-
42.0 11801-OM3 Pigtails with LC Type Connectors,pigtails for terminating fibers on the Nos. 24 686 16456
FOPP complete in all respect.

NS-14 Supplying Installation testing and Commissioning of 12 port 10/100/1000BASE-T POE

ports and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static &
43.0 RIP ,stackable upto 10 switches, should support external redundant power supply, Nos. 2 85020 170041
certified , each switch should be provided with stacking port/cable complete in all
respect

NS-15 Supplying Installation testing and Commissioning of 24 port 10/100/1000BASE-T ports

and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static & RIP
44.0 ,stackable upto 10 switches, should support external redundant power supply, certified , Nos. 6 130273 781639
each switch should be provided with stacking port/cable complete in all respect

NS-16 Supplying Installation testing and Commissioning of SFP+ 10 Gigabit Ethernet Direct
45.0 Attach Copper (twinax copper cable) 1m in length complete in all respect. Nos. 6 7954 47721

NS-17 Supplying Installation testing and Commissioning of Small Form Factor Pluggable 1
46.0 Nos. 4 9325 37299
Gigabit Ethernet (SFP+) SR Optics.

Supplying & Fixing of Floor Standing Network/Server Rack - 42U / 800w / 800d, with
Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top
& Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with
‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity
of 500Kgs. Side Panels - 42U/800d Front MS Door Perforated honeycomb 42U/800w
47.0 NS-18 Rear MS Door Split Perforated honeycomb 42U/800wFan 90CFM 230V AC, 4” dia Nos. 2 47995 95991
Castors with Brake (set of 4) Vertical Cable manager 80mmW 42U Shelf, Stationery
700mm N/W PDU 12Sockets 5/15Amps with MCB Mounting Hardware (Pkt. Of 20)
earthing Kit 150mmH Cable manager 1U MS with Loops complete in all respect.

Supply fitting, fixing and testing of 9 U Wall mount rack of Width (mm)-600, Depth (mm)
- 500, Approx.Net Wt (kg) - 20, CRCA 'D' Grade thickness (mm) - 1.2, Powder Colour
48.0 NS-19 Nos. 6 12067 72404
for Cabinet - RAL9002, Glass - 4mm Toughened Tinted Glass Door, Accessories:,
Fan & with all required acessories.

BOQ for Internal Electrification Work Page 7 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs

Supply, installation, testing & Commissioning of 8(2X4) modules brushed brass/copper

49.0 NS-20 colour pop-up boxes.(Make-Legrand, model No.-0540 18)(All switch socket, DATA Nos. 6 4114 24683
outlet, telephone etc are considered separately)

Supply, installation, testing & Commissioning of 1 module Female BNC 75 jack(Make-

50.0 NS-21 Nos. 6 2743 16456
Legrand, Model No.- 5722 76) for pop up box.

Supply, installation, testing & Commissioning of 2 Module Female HD15(VGA)(Make-

51.0 NS-22 Nos. 6 2743 16456
Legrand, Model No.- 5722 82) for pop up box.

NS-23 Supply, installation, testing & Commissioning of 2 ModuleHDMI socket (Make- Legrand,
52.0 Nos. 6 1646 9873
Model No.- 5722 81) for pop up box.

Supply, installation, testing & Commissioning of 1 Module USB charger 1000mA (Make-
53.0 NS-24 Nos. 15 1646 24683
Legrand, Model No.- 5736 21)

54.0 NS-25 EPABX

25.1 Supply Installation, Testing and Commissioning of Server Based EPABX Fully
Computerized IP System, SIP Compliant. Multi slot 19: U Rack Mountable 2U Rack
Expandable upto 500 Ports Presently Configuration as Below
CO Line 8Nos.
54.1 PRI(30 Channel) 1 Nos. Each 1 390820 390820
SIP Extension 5 Nos
Digital Extension Circuits 10Nos
Analog Extension Circuits 150 Nos.

25.2 Supply Installation, Testing and Commissioning of Integrated Viocemail System 4 Level
54.2 IVR software with 6 different languages and 4 time schedule(As per OEM). Each 1 71307 71307

Supply Installation Testing and Commissioning of Digital Phone (24Key+ 60-line DSS
Console) Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD
54.3 25.3 Each 1 30854 30854
prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support
(BCAZ),Security lock key XML open interface .

25.4 Supply Installation Testing and Commissioning of Digital analog addressable Phone 12
key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on
54.4 display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone Each 6 15084 90506
book Conference key Wall mountable Message waiting indicator.

54.5 25.5 Supply Installation, Testing and Commissioning of Digital Phone. Each 132 1508 199112

Total of Sub-Head - V carried to summary sheet 1162875 2579513

55.0 SUB HEAD - VI : FIRE ALARM & DETECTION SYSTEM

17.2.1 Supplying, installation, testing and commissioning of micro processor based intelligent
addressable main fire alarm panel, central processing unit with the following loop
modules and capable of supporting not less than 240 devices (including detectors) and
minimum 120 detectors per loop and loop length up to 2 km, network communication
card, minimum 320 character graphics/ LCD display with touch screen or other keypad
and minimum 4000 events history log
in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs
55.1 back-up with 24 volt sealed maintenance free batteries with automatic charger. The
panel shall have facility to connect printer to printout log and
facility to have seamless integration with analog/digital voice evacuation system (which
is part of the schedule of work under SH: PA System) and shall be complete with all
accessories . The panel shall be compatible for IBMS system
with open protocol BACnet/ Modbus over IP complete as per specifications.

55.1.1 17.2.1.2 Two Loop Panel Each 1 238907 238907

17.2.2 Supplying, installation, testing & commissioning of central graphical fire alarm
55.2 management system to centrally monitor and operate the fire alarm system complete Each 1 200148 200148
as required.

17.2.3 Supplying, installation, testing & commissioning of repeater panel wih 320 character/
Touch screen LCD display with inbuilt reset, acknowledge and silence switches
55.3 Each 1 108572 108572
complete as required.

17.2.4 Supplying, installation, testing & commissioning of intelligent analog addressable

55.4 photothermal detector complete with mounting base complete as required. Each 79 2846 224834

17.2.5 Supplying, installation, testing & commissioning of response indicator on

55.5 surface/recessed MS Box having two LED, metallic cover complete with all connections Each 10 263 2630
etc as required.

BOQ for Internal Electrification Work Page 8 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as
55.6 Each 5 3257 16285
required.

17.2.10 Supplying, installation, testing & commissioning of addressable fire control module
55.7 complete as required. Each 18 2990 53820

17.2.11 Supplying, installation, testing & commissioning of addressable phone control module
55.8 Each 5 3255 16275
complete as required.

17.2.14 Supplying, installation, testing & commissioning of addressable manual call point
55.9 Each 18 3859 69462
complete as required.

17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe
55.10 complete as required. Each 18 3494 62892

17.2.17 Supplying, installation, testing & commissioning of fire fighter telephone handset
55.11 Each 1 5727 5727
complete as required.

17.2.19 Supplying, installation, testing & commissioning of fire fighter phone jack complete as
55.12 Each 9 1587 14283
required.

1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single
55.13 core cable in the existing surface/ recessed steel/ PVC conduit as required.

55.13.1 1.17.2 2 x 1.5 sq. mm Metre 1900 41 77900

55.13.1 1.17.20 2 x 4 sq. mm Metre 100 86 8600

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with
55.14 accessories in surface/recess including cutting the wall and making good the same in
case of recessed conduit as required.
55.14.1 1.21.2 25 mm Metre 2000 90 180000

56.0 17.3 PUBLIC ADDRESS SYSTEM

17.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with
USB, MP3 player (including 6 zone button paging station) with seamless integration
56.1 Each 1 126399 126399
facility with main fire alarm panel for voice evacuation complete as required.

17.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete
56.2 Each 79 952 75208
as required.

17.3.3 Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall
56.3 Each 2 1780 3560
speakers complete as required.

17.3.6 Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V
56.4 Each 11 96767 1064437
rms operating at 240 volt AC supply complete as required.

17.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 zone,
56.5 Each 2 81743 163486
with microphone assembly complete as required.

17.5.3.1 Supplying, installation, testing & commissioning of speaker cable Single pair, 2-core,
56.6 Metre 1600 51 81600
1.5 sqmm

Total of Sub-Head - VI carried to summary sheet 2795025 0

57.0 NS-26 SUB HEAD - VII : IP BASE SURVEILLANCE SYSTEM (CCTV)

Supply, Installation, Testing & Commisioning of UL listed, 360 deg outdoor Dome IP
Camera with12 MP or better,the camera shall use a 1/2.3-inch, 12-Megapixel Array
format (Active) 4000(H) x 3000(V) CMOS digital Sony image sensor or better,The
camera shall incorporate:
Automatic exposure control, Automatic white balance (Range; 2500K~8000K), 50Hz
and 60Hz mains frequency flicker control, Sharpness control setting, EV compensation
control setting, 9 MP or better,100-120 dB,the camera shall use a 12 mega-pixel
resolution lens Or better, the camera shall allow the transmission of images up to 55
frames @ 9MP H.264,the camera shall support the following IP protocols: TCP/IP,
HTTP, DHCP, DNS, NTP, SMTP, Ipv4. Profile G, Profile S.The camera shall provide
57.1 26.1 Nos. 4 119988 479954
pictures down to 0.1 lux at 50 IRE / F2.0 (6500k). 60/90/180/270/ 360 degree views
.Support for 20 users simultaneously .The camera shall provide support for H.264,
Motion JPEG, H.265. The camera shall use a 12 mega-pixel lens with removable IR cut
filter.The camera shall use a lens mount of M12x0.5 thread/any other option. 3
Independent configurable streams in H.264/H.265, and 1 stream in
H.264/H.265/MJPEG. Camera shall support Micro SD card up to 512 GB.EMC to
CISPR Class A, FCC, CE, ICES-003, Safety: CE, UL/cUL and UL62368-1, UL60950-
Part 22 Certified. complete as required.

BOQ for Internal Electrification Work Page 9 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
Supply, Installation, Testing & Commissioning of 4MP Indoor IP Dome camera with
1/2.8-inch CMOS, Sensor pixels supports 2592×1520@20fps, with built in IR upto 30m
effective distance, with Sensitivity-0.05 lx (color) , Dynamic range > 90dB, day/night,
Automatic Electronic Shutter, Video compression H.264; M-JPEG, White balance, BLC,
H.264 dual-streaming, Motion/tamper/audio detection, Auto zoom Varifocal Lens 3 to
57.2 26.2 12 mm motorized lens, Built-in audio in/out capability, Two-way, full duplex Audio Nos. 16 22558 360925
support, Audio compression G.711U, Memory card slot (support minimum 32GB), 3-
axis adjustment (pan/tilt/ rotation), IP 66,IK 10, ONVIF Profile S, CE, UL, FCC Certified
.

Supply, Installation, Testing & Commissioning of 4MP IP bullet camera with 1/2.8-inch
CMOS, Sensor pixels supports 2592×1520@20fps, with built in IR upto 30m effective
distance, with Sensitivity-0.05 lx (color) , Dynamic range > 90dB, day/night, Automatic
Electronic Shutter, Video compression H.264; M-JPEG, White balance, BLC, H.264
dual-streaming, Motion/tamper/audio detection, Auto zoom Varifocal Lens 3 to 12 mm
57.3 26.3 Nos. 2 30717 61434
motorized lens, Built-in audio in/out capability, Two-way, full duplex Audio support,
Audio compression G.711U, Memory card slot (support minimum 32GB), 3-axis
adjustment (pan/tilt/ rotation), IP 66,IK 10, ONVIF Profile S, CE, UL, FCC Certified .

Supply, Installation, Testing & Commisioning of UL listed, 360 deg Dome IP Camera
with 1/2.5-inch 5-Megapixel Array format (Active) 2592(H) x 1944(V) CMOS digital
image sensor, H.264 with high profile compression, constant 360 degee recording
along with simultaneous multiple angles of view using one sensor,Each user shall be
able to create its own viewing angle in single or combination irrespective of other
client's view. For example, client 1 should be able to view a 60 degree dewarped image
while another client is able to view a 120 degree dewarped view. , 3D client side
57.4 26.4 Nos 20 23998 479954
Dewarping with no blind spots, WDR ,Multiple resolution support , bandthwidth not more
than 5 Mbps on full resolution (4 MP ) and full fram rate , support multiple users
minimum 20 user . 16 zone polygone motion detection ,10 zone privasing masking , on
borad SD card support up to 128 GB , POE support ,IP 40 & IK 10 Vandal-resistant
enclosure with Wall/Pendant Mount from the same make as Camera , UL & EN
certified

Supply of Video Management Software with built in Video Analytics management and
recording solution. The intelligent video management software shall enable
management and control of live and recorded video, seamlessly integrating analog and
digital video components. This shall be designed for small and medium sized
deployments and all-in-one architecture shall be based on one standard Server serving
as the recording server, system and client also if required, however separate
workstation should be offered for client usage. The system shall be easy to install,
configure, maintain and provides all levels of security personnel with intuitive and
reliable control. This shall enable fast detection of potential threats and emergency
event management. The INVMS shall comply with the following requirements, such as
57.5 26.5 Nos. 66 6582 434427
Hexaplex Simultaeous functioning of Live, Recordig, Playback, Video Analytics, Alarms
Handling, Configuration. The softwar eshould support Hybrid Video inputs, with high
FPS recording, Alarms Configuration and Management, High Resolution camera
support upto 12MP as minimum, Multi View split view, dewarping view of camera
should be supported for High Resolution, and multisensor/fisheye cameras. Map view,
Reports and Logs, Quick View Playback, User Pirviledges should be configurable.
Certified Make for Software - Infinova,
complete as required.

Supply, Installation ,Testing and Commissioning of Video Management Server with 30

days storage (recording to be done at 2 MP, 25 FPS). Server shall be sized according
57.6 26.6 to the solution quoted and Raid 5 redundancy shall be maintained for the servers. Nos. 1 65822 65822
complete as required.

Supply, Installation ,Testing and Commissioning of Workstation with 32" LED colour
Full HD TV monitor for Live View and Replay of Recorded View. Workstation to be
57.7 26.7 Nos. 2 75421 150843
provided with licenced antivirus.

Supply, Installation ,Testing and Commissioning of 40" industrial type display.

Resolution 1920 x 1080 (16:9), brightness atleast 450nit, viewing angle 178:178,
display colors 1 billion, built-in speakers (10W + 10W), embedded media player, video
57.8 26.8 Nos. 4 102847 411389
(HDMI1, HDMI2 except KR, NA; component CVBS common), audio (stereo mini jack),
USB 2.0 x 1.
complete as required.

Supply, installation, testing & commissioning of 24 Port Layer 2 Access POE switch
with 24 x 10/100/1000 Base T with additional 4x 1G SFP slots, equipped with power
57.9 26.9 supply and POE Budget of 185W or more. Should have Switching fabric of 56 Gbps Nos. 13 65822 855689
and 41 MPPS or more.Should support 8K MAC address. Operating Temp: 0° C to
+45° C complete as required.

BOQ for Internal Electrification Work Page 10 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
Supply, installation, testing & commissioning of 24 Port Layer 3 Core switch with 24 x
10/100/1000 Base X with additional 4x 10G SFP+ slots, equipped with power supply.
Should be capable of operating in Active-Active redundancy with stacking bandwidth of
57.10 26.10 Nos. 2 194724 389448
40Gbps. Should have Switching fabric of 128 Gbps and 95 MPPS or more.Should
support 16K MAC address. Operating Temp: 0° C to +45° Ccomplete as required.

Supply fitting, fixing and testing of 9U/42U Wall mount rack of Width (mm)-600, Depth
(mm) - 500, Approx.Net Wt (kg) - 20, CRCA 'D' Grade thickness (mm) - 1.2, Powder
57.11 26.11 Colour for Cabinet - RAL9002, Glass - 4mm Toughened Tinted Glass Door, Nos 15 13027 195410
Accessories:, Fan & with all required acessories . complete as required. complete as
required.

1.2 Supplying and fixing of following sizes of medium class PVC conduit along with
58.0 accessories in surface/recess including cutting the wall and making good the same in
case of recessed conduit as required.
58.1 1.21.2 25 mm Metre 1800 90 162000

1.5 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/
59.0
recessed Steel/ PVC conduit as required.
59.1 1.53.1 1 run of cable Metre 1800 49 88200

Total of Sub-Head - VII carried to summary sheet 250200 3885296

60.0 NS-27 SUB HEAD - VIII : UPS

BOQ for Internal Electrification Work Page 11 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Amount(Sch Amount(Non
CPWD DSR
Sr. No. Description Unit QTY. Rate edule Items) Schedule Items)
2018 Item no
Rs Rs
Supply, installation, testing & commissioning of Set of 2 Nos. 50 KVA UPS. Each UPS
of 50 KVA should have following specifications in addition to tender requirements : True
online double conversions, IGBT Rectifier & inverter based UPS. Three phases Input/
three phase output with SMF batteries complete with MS Fabricated battery rack to
accomodate the all battery system, Suitable for 30 Min backup on Full load at 0.8 Load
P.f., with 40 nos. 150AH Battery with Each UPS, Input voltage operations on mains
without switch over to battery : 340-478V at 100% load, 220-478 V @ 50% load. Input
power factor 0.99 @ 100% linear load, input THDi less than 5% @ 100% linear load.
Output THD is less than 3% for full linear load & Less than 5 % for nonlinear load. Crest
factor 3:1, over load 125% for 10 min, 150% for 1 min and should be able to operate
continuously at 115% load on bypass mode. Battery Flexible design shall be available
from 32 to 40. Battery type should be Valve regulated lead-acid (VRLA). Inbuilt Delta -
Stra shall use a lens mount of M12x0.5 thread/any other option. 3 Independent
configurable streams in H.264/H.265, and 1 stream in H.264/H.265/MJPEG. Camera
shall support Micro SD card up to 512 GB.EMC to CISPR Class A, FCC, CE, ICES- Set 1 2578038 2578038
003, Safety: CE, UL/cUL and UL62368-1, UL60950-Part 22 Certified. complete as
required.
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
                                                  
Total of Sub-Head -VIII carried to summary sheet 2578038

61.0 NS-16 SUB HEAD - IX :RACEWAY

Supports, bends, access boxes, tap off boxes and cross over as per site requirement.
(overhead / wall mounted recovery & junction boxes shall be 2.0 mm thick). The
pregalvenised sheet shall be as per IS 277 or BS 2989 having tensile strength of
minimum 500 N/sq.m. and minimum zinc coating of 275 GSM.

16.1 Supplying, installation, testing & commissioning of Race way made from minimum 2.0
mm thick GI raceway, factory fabricated, with internal partition of the following sizes
61.1 including providing removable double folded cover of 2.0 mm thick , knock out holes
and fixing accessories & coupling, earthing stud for terminating 8 SWG copper earth
wire complete as required
61.1.1 28.1 75 mm wide x38 mm deep in ceiling/floor Metre 20 3353 67056
61.1.2 28.2 100 mm wide x38 mm deep in ceiling/floor Metre 120 4011 481325
61.1.3 28.3 150 mm wide x38 mm deep in ceiling/floor Metre 75 5567 417560
61.1.4 28.4 225 mm wide x38 mm deep in ceiling/floor Metre 60 7884 473015
61.1.5 28.5 300 mm wide x38 mm deep in ceiling/floor Metre 20 9378 187566

29.0 JUNCTION BOX

Supplying, installation, testing & commissioning of floor/ceiling recessed 2 mm thick
pregavanised sheet outlet junction box including providing cover with provision to
adjust overall height, knock outs on four sides to accept raceways of specified sizes
62.0
and cutouts to fix required outlets for following size of race ways with painted GI plate (
Colour as approved Architect/Consultant).

62.1 29.1 150X150X50mm Each 50 2584 129176

62.2 29.2 300X300X50 mm Each 50 5546 277276
62.3 29.3 400X400X50 mm Each 20 7561 151227

Total of Sub-Head -IX carried to summary sheet 0 2184202

BOQ for Internal Electrification Work Page 12 of 12

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

PROJECT- DENTAL COUNCIL OF INDIA

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.
1 SUB HEAD-17.0-SANITARY INSTALLATIONS (SCHEDULE ITEM)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983
with C.I. brackets and stainless steel plug 40 mm, including painting of fittings
17.10
and brackets, cutting and making good the walls wherever required :

17.10.1.3 510x1040 mm bowl depth 200 mm Each 4 5584.10 22336.40

Providing and fixing CP Brass 32mm size bottle trap of approved quality & make
17.22A Each 29 883.05 25608.45
and as per the direction of engineer in charge.

17.34 Providing and fixing toilet paper holder :

17.34.1 C.P. BRASS Each 30 583.75 17512.50

Providing and fixing uplasticised PVC connection pipe with brass unions :
18.21
18.21.2.1 15 mm nominal bore Each 35 77.97 2728.95

Providing and fixing C.P. brass angle valve for basin mixer and geyser
18.53 Each 35 532.00 18620.00
points of approved quality conforming to IS:8931

TOTAL OF SUB HEAD-17.0-SANITARY INSTALLATIONS (SCHEDULE ITEM) 86806.30

1.2 SUB HEAD-17.0-SANITARY INSTALLATIONS (NON SCHEDULE ITEM)

Providing and fixing white vitreous china wall mounting water closet, soft close
seat cover, concealed cistern with dual flush plate, of flushing capacity 2 litre/4
NS-1 litre, including seat cover, and cistern fittings, nuts, bolts and gasket etc
complete.

Make Jaquar, WC Model No. VGS-WHT-81953UF, Concealed Cistern Model no.

JCS-WHT-2400S, Dual Flush plate Model No. JCP-CHR-152415.Kohler model K-
1.1 30 22802.90 684087
99992IN-0, cistern model no.K-77027IN-P-NA & Flush Plate-K-75890IN-P-CP.
Roca WC Model No- RS346527000, Cistern Model No. RE890010200, Dual
Flush Plate Model No. RE890195001

Providing,fixing,testing and commissioning Hand Shower (Health Faucet)

NS-2 Flexible Tube & Wall Hook of approved make and manufacture complete as per
direction of Engineer in Charge.
Make-Jaquar, Model no.ALD-CHR-565. Kohler Model No. 12927IN-CP. Roca
2.1 Each 30 869.90 26097
model no RF9060A1.

Providing and fixing Table top/ undercounter wash basins with C.I. Brackets,
32mm C.P. brass waste of standard pattern, single lever basin mixer/
Pressmatic Tap/ wall mounting,Braided hose, including painting of fittings and
NS-3
brackets, cutting and making good the walls and floors wherever required.

BOQ for Plumbing Work Page 1 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.
For guest toilet Table top- Make- Jaquar Model No. ACS-WHT-87901, Basin
Faucet-KUP-CHR-35005BPMGE. Kohler Basin Model No. K-90011T-0, Faucet
3.1 Each 11 24428.40 268712.4
Model No. K-77965T-CP. Roca Table top Basin Model No. RS32753R000, Faucet
Model No. RT5A3296C00
For Public toilet Undercounter- Make- Jaquar Model No. FLS-WHT-5701,
Pressmatic tap-PRS-031L65. Kohler Basin Model No. K-2210IN-0, Pressmatic Tap
3.2 Each 25 7149.10 178727.5
Model No. K-20747IN-8-CP. Roca Basin Model No. RS322307_ _0 , Faucet
Model No. RT5A7877C00.

Providing and fixing Chromium Plated towel ring circullar shape with
concealed fittings arrangement of approved quality and colour, of approved
NS-4
brand & manufacture complete as per direction of Engineer in Charge.

Make Jaquar, model no. AQN-CHR-7721. Kohler Model No. K-10557-CP. Roca
4.1 Each 20 780.20 15604
Model No. RA816659001.

Supply, Installation, testing & commissioning of wall mounted liquid soap

dispenser with indicator having bottom trough of soap complete in all
NS-5 Each 20 1178.20 23564
respects, including cutting and making good the wall wherever required. Make-
Jaquar, Model; no. AKP-CHR-35735P

Providing and fixing low flow type two way bib cock and flow restrictor 6 LPM
NS-6 at 3 Bar Pressure as per approved make complete in all respect as per
engineer in the charge.
Make Jaquar,Model No. FON-CHR-40041. Make kohler Model No. K-16094IN-4-
6.1 Each 30 1228.50 36855
CP. Roca Model no. RT5A9320CA1 .

Providing and fixing low flow type bib Cock with wall flange, Make- Jaquar,
NS-7 Model no.CON-CHR-047KN. Kohler Model No. K-16093IN-4-CP. Roca Model No. Each 5 667.40 3337
RT5A7820CA1.

Supply,Installation, testing & commissioning of white viterous china flat back /

half stall urinal of size 370X315X620mm including providing & fixing CI / MS
bracket (duly painted with 2 coats of paints over a coat of primer), Urinal
sensor, including CP brass waste with dome type grating, CP cast brass bottle
trap with extension piece, wall flanges complete with all accessories.Make-
NS-8 Each 9 16048.30 144434.7
Jaquar, Model no. URS-WHT-132530. Urinal Sensor Model No.- SNR-STL-51077.
Kohler Urinal Model No. K-18645IN-SS-0, Sensor Model No. K-24199IN-C03-CP.
Euronics Urinal with sensor Model No. 69101000.

Providing and Fixing C.P. brass Sink mixer with foam flow Swinging Casted
NS-9 spout & connecting legs and flanges, including cutting and making good the
walls wherever required
Make Jaquar,Model No. FLR-CHR-5165.Kohler Model No. K-20585IN-4-CP. Roca
9.1 Each 3 3009.80 9029.4
Model No. RT5A8A97CA1.

BOQ for Plumbing Work Page 2 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.

Providing, testing & commissioning of C.P. brass shower assembly comprising of

one no. concealed 2-way Diverter, one no., C.P. bath spout , shower rose with
NS-10
arm, complete including cutting and making good the wall wherever required.

Make- Jaquar, Model No. Divertor Concealed body-ALD-CHR-079, Exposed Body-

FLR-CHR-5079K. Shower rose - OHS-CHR-1989. Shower Arm-SHA-CHR-477,
Spout Model No. - SPJ-CHR-429. Kohler Model no. Divertor Concealed-K-882IN-
10.1 CP, Exposed Body- K-99472IN-4FP-CP, Shower Rose With Arm K-16356IN-A-CP. Each 8 8630.20 69041.6
Spout K-99467IN-CP. Roca Shower Mixer with spout model No. RT5A0296C00,
Shower rose with arm Model No. RT18700A1.

Providing and fixing 600mm Long size CP brass towel rail with CP brackets fixed
NS-11 to wooden cleats, PVC rawl plug with CP brass screws etc. including cutting and
making good the wall wherever required.
For Tower C & Servant Toilet, Make- Jaquar, Model No. ACN-CHR-1181FS.
11.1 Kohler Model No. K-25065IN-CP. Roca Model No. RA816656001. Each 8 1720.60 13764.8

Providing and fixing soap Dish Holder with concealed fitting arrangements.
NS-12 Make Jaquar Model no. CAN-CHR-429.Kohler Model No. K-5634IN-CP. Roca Each 8 500.10 4000.8
Model No. RA816070132.

Supplying, installing, testing and commisioning of PP mineral filled low noise

pipes and fittings, with push fit rubber ring sockets pipes and fittings confirming
to EN-12056 , with density 1.9gm/cm3. Piping is to be suspended from ceiling
level & fixed on ceiling with necessary fittings and cutting the pipe to the
required length including short pieces, assorted fittings such as Plug / Plain Tee
/ Swept Tee with or without door, bends and elbows or any other standard
fittings are included in the rate. The pipe should have B1 fire classification
NS-13 according to EN4102 and is hot water resistant up to 95⁰C for short term
loading & 90⁰C long term loading and has chemical resitance of pH 2-12 and
completly provides sound protection upto 10 dB at a flow rate of 2 LPS and
giving water tightness test for all the piping (refer technical specifications for
additional details.) The rate shall include chasing of walls, laying of pipes as per
standard working procedures. (For soil, waste and rain water pipe)

All the internal drainage pipes are to be suspended below the ceiling level and
the pipes are to be supported by modular clamps. The rate includes the cost of
all types of clamping and no other separate rate shall be given.

The supports required for the Pipes should be made up of cold rolled steel of
quality DX51 or greater with minimum GSM of 275 or greater and should have
universal mounting slot on the front of the rail for accurate positioning of
fasteners and system compatible round and long holes on back of the rail the
pipe.

BOQ for Plumbing Work Page 3 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.
The pipe clamps should be either split type with EPDM inner rubber lining or
should be MSS-SP manufactured with FM approval and UL listing.

Threaded rods should be of 4.8 strength class or greater and necessary

accessories such as Hexagonal Nuts and Bolts should be of 8.8 strength
class.For Soil, Wate & rain water Pipe
13.1 a) 40 mm dia Metre 35 658.60 23051
13.2 b) 50 mm dia Metre 35 865.70 30299.5
13.3 c) 63 mm dia Metre 28 959.00 26852
13.4 d) 75 mm dia Metre 120 1067.00 128040
13.5 e) 110 mm dia Metre 450 1711.50 770175

BOQ for Plumbing Work Page 4 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.
Providing & Fixing Low Noise Floor trap with minimum 50mm water seal having
3nos of DN 50mm inlets and 1nos of DN 110mm Top inlet and 1nos of DN
110mm outlet. The baffle construction should be air tight under all
circumstances. The inspection plug should enable to access the area under the
baffle in order to inspect and clean the area. The Floor Trap volume should be
NS-14
in such a way that a maximal discharge capacity is reached. In case not all the
inlets are used two PP-blind plugs are added to the Floor Trap. These blind
plugs should secure a leakage free sealing of unused connections to the Floor
Trap. Make: Poloplast, Astral (Silencio), Rehau or equivalent

14.1 110 x110 mm outlet Each 40 1711.80 68472

Providing and fixing floor trap height riser fitting with maximum 3 inlets 40,50
or 63 mm size,fixed to PP trap set in cement concrete as per standard drawing
NS-15 Each 40 1198.00 47920
complete in all respect as directed by Engineer-incharge.

Providing & fixing 110mm x 50mm uPVC waste with reducing elbow & nipple
cutting chases, the floor / slab, repairs complete as required and connection to
NS-16 Each 10 555.00 5550
uPVC waste pipe complete in all respect as directed by Engineer-in-charge.

Providing and fixing Brass Floor Clean Out plug with suitable insert keys for
opening to soil pipe / waste pipe of uPVC pipe as required complete as per
NS-17
drawing, approved sample and direction by Engineer-in-charge:

17.1 110 x110 mm outlet Each 40 653.60 26144

Providing and fixing 125mm chromium plated grating with ring and S.S anti
cockroach basket and two S.S screws of approved design with grating screwed
NS-18 down to the ring with s/s screws and embedding and setting ring into the floor Each 50 598.90 29945
with cement mortar .(As per approved make or equivalent)

Providing and fixing chrome plated grating with ring and two S.S screws of
approved design with grating screwed down to the ring with s/s screws and
NS-19 Each 5 931.30 4656.5
embedding and setting ring into the floor with cement mortar .(As per
approved make or equivalent)

providing and fixing motorised butterfly valve rating PN 1.0 with float type
sensors suitable for 240 volts with working pressure rating of not less than 5
kg/cm2 with contol panel and sensors to open valve when water level is low in
NS-20
tanks and to close when water level is high in water tanks including butterfly
valves, necessary cables, conduits, upto junction box etc. complete. (upto 6 mt
qty approx.)
20.2 32 mm dia (OHT Filling) Each 1 14990.20 14990.2
20.3 40 mm dia (OHT Filling) Each 1 17486.60 17486.6

2670837.00
TOTAL OF SUB HEAD-17.0-SANITARY INSTALLATIONS (NON-SCHEDULE ITEM)

BOQ for Plumbing Work Page 5 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.

2 SUB HEAD-18.0-WATER SUPPLY(SCHEDULE ITEM)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
stability for hot & cold water supply, including all CPVC plain & brass threaded
fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes
18.7
jointing of pipes & fittings with one step CPVC solvent cement and testing of
joints complete as per direction of Engineer in Charge.

18.7.1 15 mm dia Metre 10 241.55 2415.5

18.7.2 20mm dia Metre 110 306.95 33764.5
18.7.3 25mm dia Metre 65 369.20 23998
18.7.4 32mm dia Metre 65 480.55 31235.75
18.7.5 40mm dia Metre 45 648.60 29187
18.7.6 50mm dia Metre 55 903.50 49692.5
Derrived 65mm dia Metre 5 1322.00 6610

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC plain &
18.9 brass threaded fittings This includes jointing of pipes & fittings with one step
CPVC solvent cement, trenching, refilling & testing of joints complete as per
direction of Engineer in Charge.
External work
18.9.2 20 mm nominal bore Metre 20 253.70 5074
18.9.3 25 mm nominal bore Metre 20 326.65 6533
18.9.4 32 mm nominal bore Metre 30 413.70 12411

18.16. Providing and fixing brass stop cock of approved quality

18.16.1 15mm dia nominal bore Each 8 302.55 2420.4

Providing and fixing gun metal gate valve with C.I. wheel of approved quality
18.17
(screwed end) :
18.17.1A 20 mm dia nominal bore Each 30 460.20 13806
18.17.1 25 mm dia nominal bore Each 10 497.15 4971.5
18.17.2 32 mm dia nominal bore Each 6 581.25 3487.5
18.17.3 40mm dia nominal bore Each 8 678.40 5427.2
18.17.4 50mm dia nominal bore Each 3 869.20 2607.6
18.17.5 65mm dia nominal bore Each 1 1488.10 1488.1

TOTAL OF SUB HEAD-18.0-WATER SUPPLY (SCHEDULE ITEM) 235130

Providing and fixing Pliable PEX piping (Pipe in pipe) system ,concealed
and ceiling, chase cutting, NSF approved with crimp/compression joints
NS-21 as required, Modular Manifold, Cabinate for modular manifold, end plug,
Pex pipe adaptor, bracket for elbow, conduit etc. to complete the work.

21.1 Pex pipe with conduit Metre 700 314.40 220080

21.2 Manifold wih Throtling valve with 3 nobs Each 40 2081.30 83252
21.3 Plastic Box + Brackets Each 26 2077.60 54018
21.4 End cap female 16mm Each 170 569.30 96781
21.5 Male Adaptor 16x1/2mm Each 130 571.10 74243
21.6 Female Adaptor 16x1/2mm Each 130 617.10 80223

BOQ for Plumbing Work Page 6 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.
TOTAL OF SUB HEAD-18.0-WATER SUPPLY (NON SCHEDULE ITEM) 608597

3 SUB HEAD-18.0-EXTERNAL WATER SUPPLY

Excavating trenches of required width for pipes cables etc including excavation
for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m
2.10 ncluding getting out the excavated soil , and then returning the soil as required
, in layers not exceeding 20 cm in depth including consolidating each deposited
layer by ramming, watering, etc. and disposing of surplus excavated soil as
directed , within a lead of 50 m.
2.10.1 All kind of soil

2.10.1.2 Metre 100 364.20 36420

Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality
18.17
(screwed end) :
18.17.1 25mm nominal bore Each 4 497.15 1988.6
18.17.2 32mm nominal bore Each 1 581.25 581.25
18.17.3 40mm nominal bore Each 1 678.40 678.4
18.17.4 50mm nominal bore Each 1 869.20 869.2
18.17.5 65mm nominal bore Each 1 1488.10 1488.1

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement

mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box
100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4
18.32 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),
i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand :
10 graded stone aggregate 40mm nominal size ) and inside plastering with
cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a
floating coat of neat cement complete as per standard design :

18.32.1 Each 2 1582.45 3164.9

With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box
100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside)
with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
18.33
stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation
concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat cement complete as per
standard design :

18.33.1 Each 1 9288.40 9288.4

With common burnt clay F.P.S (non modular) bricks of class designation 7.5

BOQ for Plumbing Work Page 7 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.

Providing & fixing enclosed type water meter ( bulk type ) conforming to IS :
18.60
2373 and tested by municipal board complete with nuts , bolts , rubber
insertion etc . ( The tail piece if required will be paid saperately )
18.60.1 80 mm dia nominal bore Each 1 3576.10 3576.1
TOTAL OF SUB HEAD-18.0-WATER SUPPLY (SCHEDULE ITEM) 58054.95

4 SUB HEAD : 12 - ROOFING(SCHEDULE ITEM)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm
12.22 Each 6 244.05 1464.3
nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm
cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,
rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15
12.44 Each 6 47.25 283.5
cm diameter and weighing not less than 440 grams.

TOTAL OF SUB HEAD : 12 - ROOFING 1747.80

4 SUB HEAD : 19 - EXTERNAL DRAINAGE SYSTEM

Excavating trenches of required width for pipes cables etc including excavation
for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m
2.10 ncluding getting out the excavated soil , and then returning the soil as required
, in layers not exceeding 20 cm in depth including consolidating each deposited
layer by ramming, watering, etc. and disposing of surplus excavated soil as
directed , within a lead of 50 m.
2.10.1 All kind of soil

2.10.1.2 Metre 50 364.20 18210

Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff
19.1 mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand)
including testing of joints etc. complete:
19.1.1 100 mm diameter Metre 5 317.05 1585.25
19.1.2 150 mm diameter Metre 10 500.20 5002
19.1.3 200 mm diameter Metre 10 794.25 7942.5

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10

19.2 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed
concrete as per standard design:
19.2.1 100mm dia SW / R.C.C. pipe Metre 5 817.00 4085
19.2.2 150mm dia SW / R.C.C. pipe Metre 10 999.15 9991.5
19.2.3 200mm dia SW / R.C.C. pipe Metre 10 1164.80 11648
19.2.4 250mm dia SW / R.C.C. pipe Metre 10 1346.95 13469.5

BOQ for Plumbing Work Page 8 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I.
19.4 grating brick masonry chamber with water tight C.I. cover with frame of 300
x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame
to be not less than 2.70 kg as per standard design :
19.4.2 150 x 100mm size P-type

19.4.2.1 Each 6 2317.40 13904.4

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars
19.6
jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement :
2 fine sand) including testing of joints etc. complete :
19.6.2 150mm dia RCC pipe Metre 10 462.60 4626
19.6.3 250mm dia RCC pipe Metre 10 754.45 7544.5

Constructing brick masonry manhole in cement mortar 1:4 (1cement : 4 coarse

sand) with RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded
19.7 stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement :
4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering
12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with
floating coat of neat cement and making channels in cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
finished with a floating coat of neat cement complete as per standard design.
Inside size 90 x 80 cm and 45 cm deep including pre-cast R.C.C. manhole cover
19.7.1 and frame of required shape and approved quality H D - 20 Circular shape 560
mm internal diameter.

19.7.1.1 Each 2 10905.05 21810.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium
19.7.2
duty) 500 mm internal diameter, total weight of cover and frame to be not less
than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :

19.7.2.1 Each 1 22939.65 22939.65

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.8 Extra for depth for manholes:

19.8.1 Size 90 x 80 cm

19.8.1.1 Metre 1 7503.00 7503

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.8.2 Size 120x90 cm

19.8.2.1 Metre 1 8994.60 8994.6

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

BOQ for Plumbing Work Page 9 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom
and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), inside
cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)
19.9 finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1
cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and
making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 20 mm nominal size) finished with a floating coat of
neat cement, all complete as per standard design :

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade
designation) 560 mm internal diameter conforming to I.S. 12592, total weight
19.9.1 of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
including centering, shuttering all complete. (Excavation, foot rests and 12mm
thick cement plaster at the external surface shall be paid for separately):

19.9.1.1 Each 1 11038.10 11038.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond
19.10
0.91 m to 1.67 m

19.10.1 Metre 1 6448.40 6448.4

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22m internal dia at bottom and
0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement
plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished
19.11 with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3
coarse sand : 6 graded stone aggregate 40mm nominal size) and making
necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20mm nominal size) finished with a floating coat of
neat cement, all complete as per standard design :

1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation)
560mm internal diameter conforming to I.S. 12592, total weight of cover and
19.11.1 frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm nominal size) including
centering, shuttering all complete. (Excavation, foot rests and 12 mm thick
cement plaster at the external surface shall be paid for separately) :

19.11.1.1 Each 1 21235.65 21235.65

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond
19.12
1.68 m to 2.29 m :

19.12.1 Metre 1 8368.40 8368.4

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

BOQ for Plumbing Work Page 10 of 11

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

CPWD DSR
2018 Item
Rate (in
No/Non Description of item Unit TOTAL Amount
Rs.)
Shadule
Item No.

Providing orange colour safety foot rest of minimum 6 mm thick plastic

encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786
having minimum cross section as 23 mmx25mm and over all minimum length
263 mm and width as 165mm with minimum 112 mm space between
19.16 protruded legs having 2 mm tread on top surface by ribbing or chequering Each 30 377.09 11312.55
besides necessary and adequate anchoring projections on tail length on 138
mm as per standard drawing and suitable to with stand the bend test and
chemical resistance test as per specifications and having manufacture's
permanent identification mark to be visible even after fixing, including fixing in
manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of
19.19
required shape and approved quality
19.19.1 LD - 2.5
19.19.1.1 Rectangular shape 600x450 mm internal dimensions Each 4 1228.90 4915.6

19.19.2 M D - 10
19.19.2.2 Circular shape 500 mm internal diameter Each 2 1035.60 2071.2

Constructing brick masonry road gully chamber 50x45x60cm with bricks in

19.27
cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast
RCC horizontal grating with frame complete as per standard design.

19.27.1 Each 4 5209.10 20836.4

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

TOTAL OF SUB HEAD : 19 -EXTERNAL DRAINAGE SYSTEM 245482.30

BOQ for Plumbing Work Page 11 of 11

Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

SUBJECT: TENDER FOR PUMPS AND EQUIPMENTS

Rate
S.N. ITEM DESCRIPTION Unit Qty Amount ( in Rs.)
(in Rs.)
I PUMPS AND EQUIPMENTS

Dom. + Flushing Water Pump

NS-1 Supply, installation, testing and commissioning of a set of
hydropneumatic vertical/horizontal inline water transfer pump set, skid
mounted with PLC panel factory fitted, for domestic water with single
Floating VFD suitable for automatic operation and delivering the specified
discharge at the specified head. Each Pump shall be of stainless steel
(SS-304) casing in along with NRV & ball/butterfly valves at suction &
delivery line, impeller and shaft in ss 304 and shaft and sleeve with
mechanical seal capable of delivering suitable capacity and connected by
a flexible coupling to a totally enclosed fan cooled (TEFC) induction motor
as per IEC standard. The set shall be complete with gunmetal isolation
valve on the suction line with 150mm dia pressure gauge, (make- lubi,
Ebara, grundfos) gunmetal non - return valve and gunmetal isolation
valve on delivery line, complete with s/s suction and delivery header
piping of suitable size. The motor shall be suitable for 415 ± 10% volts, 3
phase, 50 Hz A.C. power supply. The set shall include an automatic
control panel and FRP presssure tank of capacity 200 lts. with common
base frame and complete connecting accessories. The set shall be
completely equipped with floating variable fequency drive for automatic
operation as per load requirements and will run alternately in sequence in
cascade mode based on water demand. The pump set includes pressure
switch along with dry running preventor and necessary cable from panel
to pump and sensor to panel etc. complete.

2.1 Dom. water transfer pumps (UGT Level)

No. of Pumps : 2 (1 Working + 1 Stand by)
Capacity : app. 80 LPM each
Head : 50 M
(complete set as mentioned above) Set 1 447773.50 447773.5

2.2 Dom. water transfer pumps at (terrace level)

No. of Pumps : 2 (1 Working + 1 Stand by)
Capacity : app. 100 LPM each
Head : 25 M
(complete set as mentioned above) Set 1 375509.60 375509.6

Plant room + Drainage Sump Pump

NS-3 Providing and fixing compact monoblock submersible pumps of suitable
rating, with non-clog free flow open impeller, solid handling capacity of
upto at least 50mm suitable for operation on 415 volts +10% , 3 Phase,
50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for
lifting & lowering of pump, M.S. galvanized lifting chain, complete. The
pump sets shall be (make- lubi, Ebara, grundfos) supplied with required
accessories & as per specification with the following :

(e) Electrical control panel having all necessary accessories & safety
devices of standard specifications and suitable for receiving incommer
cable from main plumbing panel to conncet sump pump panel complete
as required. (Panels with sump pumps near each sump as per site
conditions). --1 No.
Each set consist of 2 nos.of pumps - 1 working & 1 stand by (Complete
set as above with 2 nos. pumps including cost for valves, piping, Control
Panel and Cabling, Level Controllers etc as required and as specified)
2.The entire system alongwith pumps & control panel must be sourced
from single manufacturer only for unit responsibility.

NS-4 Discharge - 180 LPM Each

Page 1 of 4
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Rate
S.N. ITEM DESCRIPTION Unit Qty Amount ( in Rs.)
(in Rs.)
Total head - 15 Meters (minimum) Set 2 132440.10 264880.2

Level Controller/ Level Indicators

NS-9 Supply, Installation, Testing and Commisioning of magnetic float type
Level Controllers / Indicators having adequete number of switches
(Minimum 5 Nos.) for the services mentioned below. Contoller equipment
shall be mounted inside the electrical panels of the various pumps, while
the sensors shall be installed in the corrosponding tanks (roof or the side
wall - as the case may be). Controllers shall have sufficient number of
contacts to switch on / off the pumps, indicate status, provide signal for
remote indication of water level (either as percentage of full level or in
cms) and trigger visual/audio alarm.

9.1 For Raw water tank for the following levels.

(a) Overflow level to trigger alarm & switch OFF the incoming supply of water.
(b) 1/2 full to switch ON the incoming supply of water
(c) Low level (less than 1/5 of total depth) to trigger alarm & switch ON the Filter
Set 1 15363.50
feed pump 15363.5

9.2 For Treated water tank for the following levels.

(a) Overflow level to trigger alarm & switch OFF the Filter feed pump
(b) 1/2 full to switch ON the Filter feed pump
(c) Low level (less than 1/5 of total depth) to trigger alarm & switch ON the Set 15363.50
1
Filter feed pump 15363.5

II PIPING , VALVES AND ACCESSORIES

NS-10 Providing and fixing reinforced neoprene rubber vibration
eliminators/expansion joints (to provide relief from stresses at pipe
flanges) suitable for upto 20 kg/cm2 pressure, as per specification of the
manufacturers complete as required and as specified complete as per
directions of the engineer-in-charge.
10.1 32mm dia Each 4 1755.80 7023.2
10.2 40mm dia Each 2 2048.50 4097
10.3 50mm dia Each 2 2341.10 4682.2
10.4 65mm dia Each 2 2633.70 5267.4

NS-11 Providing and fixing M.S. grating and preferably in 600mm long pieces,
fabricated with 16x16mm square bars, @ 20mm clear spacing and
welded to angle iron 25x25x5mm and placed firmly on angle iron frame of
30x30x5mm with 25x3mm hold fasts approximately 75mm long welded
at intervals of 500mm including two or more coats of synthetic enamel
paint of approved quality and shade over one coats of primer and set in
cement mortar 1:3 (1 cement : 3 coarse sand) complete as per
attached details for drain.
KG 50 385.80 19290

NS-12 Providing, fixing, testing & commissioning RO plant of below Capacity

including RO filter feed pump 2 nos of (1W+1S) and high pressure
pump in SS-304 casing, SS-304 impeller, SS-316 shaft, CI base
multigrade filter, activared carbon filter, RO membranes, antiscalant
chemical dosing, PH correction, ultra-filtration with UV, storage tank for
storing R.O. water tank . made of 3mm thick SS-304 grade sheet,
monoblock Pressure pump (1W+1S) 2900 rpm single phase, Vertical
pressure tank (20/24Ltr), Pressure switch, Pressure Gauge, Float Switch,
electric panel all complete to the utmost satisfaction of engineer in
charge.

Plant of 250 LPH Capacity With 500 ltr Storage tank. Set 1 760857.60 760857.6

Page 2 of 4
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Rate
S.N. ITEM DESCRIPTION Unit Qty Amount ( in Rs.)
(in Rs.)
NS-13 Design, Supply, Installation, testing and commissioning of Sewage
Treatment Plant (STP) of 20 kld capacity in mechanical type of approved
make for the treatment of domestic sewage using advanced Moving Bed
Bio Reactor(MBBR) Technology, including, getting the design approved
from engineer in charge, operation and maintenance for 1 year after
successful commissioning of the plant including all consumables etc all
complete as per drawings (Make-BS Enviro, Aldee water, Ecoguard).,
relevant standards, technical specifications, polution control board local
bye laws, and direction of Engineer-In-Charge. The characteristics of the
Influent and desired quality of Treated water from the System are
mentioned in the technical specifications. The system shall be complete
with all equipments including Air Blowers, pumps for mechanical
functional and irrigation transfer,Flushing transfer pump, MBBR media, air
diffusers,ozonator, internal piping etc, MS tanks , Activated Carbon
Filters, Dual Media Filters, electrical panels, Ultrafiltration, ozonator, Pva
gel media cabling etc complete in all respect. Blowers and pumps will be
in combination of one working and one standby. Details of equipment
shall be as mentioned in the Technical specifications. .Make-BS Enviro,
Aldee water, Ecoguard.

Job 1 2387950.60 2387950.6

NS-14 Supply, installation, testing and commissioning at levels and locations,

approved make Flat Plate Collector based Pressurised Solar water
heating system with heat exchanger, Heat pump, Water to be Heated by
heat pump = 475 LPH with a minimum COP of 3.8., of capacity
1000LPD rated at 600 C with 1000ltr SS storage tank, (Heat pump make-
Ensys, A.O. Smith, Stiebel Elton. solar make ,Boss, Uratom, sunbirds)
.comprising of polyester coated aluminium famed flat plate collectors with
black chrome coated copper as absorber material (absorbity of collector >
95%) having aluminium back sheet and top as toughened glass with
transmittivity > 85% fitted using EPDM beading and grommets and
mounted on polyester powder coated MS structure, including copper
header and riser pipe welded by ultrasonic/ Laser welding, storage tank,
valves, vents, drain, connection piping arrangement, conduits, cabling,
insulation, temperature controller, grounding the system properly using
die and fasteners all complete as per relevant sts, Ultrafiltration, ozonator,
Pva gel media cabling etc complete in all respect.

Set 1 658434.50 658434.5

TOTAL C/O TO SUMMARY NON SCHEDULE ITEM 4966492.8

DSR - 10 Provding and fixing heavy duty G.I. pipe (For Suction & Delivery of pumps
and equipment) confiming to IS. 1239 upto 150 mm and IS 3589 for dia
200 mm and above with reducers, tees, flanges, elbow, crosses, union
etc. and fixing the pipes on wall / ceiling / beam / floor including
Clamping/Supporting the same, including painting with 2 coats of
synthetic enamel paint as per the site requirement and shall be duly
painted with two coats of approved quality synthetic enamel paint &
shade over a readymix primer coat complete as required & as per
directions of the engineer-in-charge for the following sizes:

10.1 32mm dia Metre 8 626.00 5,008.00

10.2 40mm dia Metre 8 763.00 6,104.00
10.3 50mm dia Metre 15 859.00 12,885.00
10.4 65mm dia Metre 10 1076.00 10,760.00
10.5 80mm dia Metre 5 1252.00 6,260.00

Page 3 of 4
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.
Rate
S.N. ITEM DESCRIPTION Unit Qty Amount ( in Rs.)
(in Rs.)
DSR - 13 Providing and fixing C.I butterfly valve, class PN 1.6 as per I.S:13095 or
BS:5155, including necessary nuts, bolts, gaskets / flanges etc., complete
as required and specified by the engineer-in-charge.

13.1 40mm dia Each 3 3509.00 10,527.00

13.2 50mm dia Each 1 3671.00 3,671.00
13.3 65mm dia Each 1 4149.00 4,149.00
13.4 80mm dia Each 1 4842.00 4,842.00

DSR - 14 Providing & fixing C.I horizontal/vertical type non return valve (dual
plate) conforming to IS:5312 with C.I. body, SS Disc, SS stem, EPDM
seal, complete with companion flanges, bolts, nuts, washers & inserted
rubber gasket complete as required to I.S:5312, Part-I, dual plate type,
class PN 1.6.
14.1 40mm dia Each 1 5646.00 5,646.00
14.2 50mm dia Each 1 5646.00 5,646.00
14.3 65mm dia Each 1 6274.00 6,274.00
14.3 80mm dia Each 1 7539.00 7,539.00

DSR - 15 Providing, installation, testing and commissioning of stainless steel Y-

strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet
with 3 mm dia holes with stainless steel flange.
15.1 80mm dia Each 1 4573.00 4,573.00
TOTAL C/O TO SUMMARY 93 884.00

Page 4 of 4
 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

PROJECT :- DENTAL COUNCIL OF INDIA

Ref. No.
S. Amount Sch. Amount Non
DSR- Description Of Items Unit Qty Rate (Rs.)
No. (Rs.) Sch. (Rs.)
12/16

SUB HEAD - I - (WET RISER SYSTEM - PUMPING

1.0 EQUIPMENTS)

Supply, Installation, Testing and Commissioning of Electric

Driven Main Fire Pump suitable for auto operation &
consisting of following: complete in all respect as
1.1 required.Make- Lubi, Ebara, Grundfoss.
Horizontal Single Inlet,Multistage, multi outlet outlet, end
suction type centrifugal pump of cast iron body and bronze
impeller with stainless steel shaft, mechanical seal to ensure
a minimum pressure of 3.5 kg/sq. cm.2280 LPM capacity of
head 110 meter at highest and farthest outlet at specified flow
of as Mentioned Below confirming to IS 1520-1980.

Suitable HP squirrel cage induction motor, TEFC

synchronous speed 1450 RPM (with permissible slip),
suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP
55 protection for enclosure, horizontal foot mounted type with
Class-' F' insulation, confirming to IS-325-1978.

Common base frame fabricated out of M.S channel of

suitable size, flexible coupling, coupling guard, foundation
bolts and pressure gauge with valve etc. Suitable cement
concrete foundation (minimum 6" above from ground floor)
duly plastered, with anti vibration pads etc. complete as per
manufacturer's design & standards and as per detailed
specifications.
a) 2280 LPM capacity of 110 meter Head Set 2 512742.00 1025484
Supply, Installation, Testing and Commissioning of Diesel
Engine Driven Main Fire Pump suitable for auto operation
and consisting of following: complete in all respect as
1.2 required. Make- Lubi, Ebara, Grundfoss.
Horizontal Single Inlet,Multistage, multi outlet, end suction
type centrifugal pump of cast iron body and bronze impeller
with stainless steel shaft, mechanical seal to ensure a
minimum pressure of 3.5 kg/sq. . at highest and farthest
outlet at specified flow of 2280 LPM capacity of head 110
meter confirming to IS 1520-1980.

Suitable HP 1500 RPM, 4 stroke, cold starting type Diesel

Engine with Heat Exchanger confirming to relevant BIS & IS
Standards, complete with all required accessories / system,
fuel oil filter, lubricant oil pump with filter, 2 Nos. starting
batteries of 180 AH capacity each with suitable angle iron
stand, engine starting panel having all the controls meters,
gauges, tachometer, hour meters, starting switch with keys
for manual starting, auto starting mechanism, 24 Volts
electric starting equipment, Diesel Tank for 8 hrs continuous
running of diesel engine, having minimum capacity of 200
Ltrs. (tank made out of 3mm thick M.S. Sheet with filling Cap,
drain Cock, diesel indicator duly mounted on M.S. angle)
exhaust pipe extended upto 1 mtr. outside pump house, duly
insulated with 50 mm. thick glass wool with 1.0 mm. thick
aluminium sheet cladding, exhaust residential silencer, stop
solenoid for auto stop in the event of fault with audio
indications, painted with post office red colour etc. as
required.

M.S. fabricated Common base frame, flexible coupling,

coupling guard, foundation bolts and pressure gauge with
valve etc. Suitable cement concrete foundation (minimum 6"
above from ground floor) duly plastered, with anti vibration
pads etc. complete as per manufacturer's design & standards
and as per detailed specifications.

BOQ for Fire Fighting Work Page 1 of 6

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Ref. No.
S. Amount Sch. Amount Non
DSR- Description Of Items Unit Qty Rate (Rs.)
No. (Rs.) Sch. (Rs.)
12/16
a) 2280 LPM capacity of head 110 meter Set 1 722964.21 722964.2082

Supplying, Installation, Testing and Commissioning of

Electric Driven Pressurization Pump (Jockey Pump)
suitable for auto operation and consisting of following:
complete in all respects as required.Make- Lubi, Ebara,
1.3 Grundfoss.

Horizontal Single Inlet,Multistage, multi outlet, end suction

type centrifugal pump of cast iron body and bronze impeller
with stainless steel shaft, mechanical seal to ensure a
minimum pressure of 3.5 kg/sq. , gland packing and flow of
180 LPM capacity of head 110 meter confirming to IS:1520-
1980.

Suitable HP squirrel cage induction motor TEFC type 2900

RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC
with IP 55 class of protection for enclosure, horizontal foot
mounted type with Class -'F' insulation, confirming to IS:325-
1978.
Common base frame fabricated out of M.S channel of
suitable size, flexible coupling, coupling guard, foundation
bolts and pressure gauge with valve etc. Suitable cement
concrete foundation (minimum 6" above from ground floor)
duly plastered, with anti vibration pads etc. complete as per
manufacturer's design & standards and as per detailed
a) specifications. Set 2 158717.92 317435.8353

TOTAL CARRIED TO SUMMARY (SCHEDULE ITEM) 2065884.04

SUB HEAD - II - (HYDRANT, PIPING, VALVES AND

2.0 ACCESSORIES)
Providing & fixing of heavy class M.S. pipes conforming to
IS: 1239/3589 complete with fittings including trenching and
refilling etc. (external work) including all fittings and
accessories like tees, elbows, flanged joints, rubber insertion,
nuts, bolts or cutting and welding joints. Providing thrust block
at distance specified as per specifications. (Pipe shall be
6.1 provided with anti corrosive protective treatment with coal
tar/asphalt tape confirming to IS: 10221 standard complete as
per specification). All work complete as per specification and
as directed by Engineer-In-Charge. (All the fitting i.e. tee
/elbow etc. for Valve connections etc. will be flanged joints)(
Heavy duty pipe )
2.1
6.2.2 a) 80 mm dia Meter 10 2238.80 22388.0

Providing laying, testing & commissioning of 'C' class heavy

duty MS Pipe conforming to IS 1239/3589 i/c fittings like
elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in
ground including welding, excavation & providing cement
6
concrete blocks as supports, anticorrosive treatment with
coaltar/asphalt tape as per IS 10221, refilling the trench etc.
of following sizes complete as required.
DSR-6
6.2 6.1 150 mm dia Meter 120 2376 285120

SLTC of M.S. pipe on surface

BOQ for Fire Fighting Work Page 2 of 6

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Ref. No.
S. Amount Sch. Amount Non
DSR- Description Of Items Unit Qty Rate (Rs.)
No. (Rs.) Sch. (Rs.)
12/16
Providing, laying, testing & commissioning of 'C' class heavy
duty MS pipe conforming to IS 3589/IS 1239 including
Welding, fittings like elbows, tees, flanges, tapers, nuts bolts,
7 gaskets etc. and fixing the pipe on the wall/ceiling with
suitable clamp/support frame and painting with two or more
coats of synthetic enamel paint of required shade complete
DSR-7 as required :
7.1 7.1 25 mm dia Meter 450 471.00 211950
7.2 7.2 32 mm dia Meter 150 527.00 79050
7.3 7.3 40 mm dia Meter 170 651.00 110670
7.4 7.4 50 mm dia Meter 95 787.00 74765
7.5 7.5 65 mm dia Meter 68 1004.00 68272
7.6 7.6 80 mm dia Meter 110 1122.00 123420
7.7 7.7 100 mm dia Meter 115 1499.00 172385
7.8 7.8 150 mm dia Meter 130 2064.00 268320
7.9 7.9 200 mm dia (6mm thick) Meter 8 2926.00 23408
7.10 7.10 250 mm dia (6mm thick) Meter 8 3521.00 28168

Supplying and fixing single headed internal hydrant valve with

instantaneous Gunmetal/Stainless Steel coupling of 63 mm
9 dia with cast iron wheel ISI marked conforming to IS 5290
(Type -A) with blank Gunmetal/Stainless Steel cap and chain
DSR-9 as required :
9.1 9.1 Single headed Gunmetal Each 16 7949 127184

Supplying and fixing Single headed external yard hydrant

valve with 1 No. 63 mm dia instantaneous FM
10 Gunmetal/Stainless Steel coupling and cast iron wheel, ISI
marked, conforming to IS 5290 (type A) with blank
DSR-10 Gunmetal/Stainless Steel cap and chain as required :
10.1 10.2 Single headed Stainless Steel Each 6 5987 35922

Supplying, fixing, testing and commissioning of butterfly valve

of PN 1.6 rating with bronze/gunmetal seat duly ISI marked
11
complete with nuts, bolts, washers, gaskets conforming to IS
DSR-11 13095 of following sizes as required :
11.1 11.2 50 mm dia Each 1 3671 3671
11.2 11.3 65 mm dia Each 1 4149 4149
11.3 11.4 80 mm dia Each 4 4842 19368
11.4 11.5 100 mm dia Each 4 6454 25816
11.5 11.6 150 mm dia Each 6 8699 52194

Supplying, fixing, testing & commissioning of double flanged

sluice valve of rating PN 1.6 with non rising spindle,
12 bronze/gun metal seat, ISI marked complete with nuts, bolts,
washers, gaskets and conforming to IS 780 of following sizes
DSR-12 as required :
12.1 12.6 150 mm dia Each 1 22550 22550
12.2 12.7 200 mm dia Each 1 39133 39133
12.3 12.8 250 mm dia Each 1 46318 46318

Providing, installation, testing and commissioning of non-

return valve of following sizes confirming to IS: 5312
13
complete with rubber gasket, GI bolts, nuts, washers etc.as
DSR-14 required :
13.1 14.4 80 mm dia Each 2 7539 15078
13.2 14.5 100 mm dia Each 4 10836 43344
13.3 14.7 150 mm dia Each 2 17577 35154
13.4 14.8 200 mm dia Each 1 29075 29075

Providing, installation, testing and commissioning of

stainless steel Y-strainer fabricated out of 1.6 mm
14
thick stainless steel, Grade 304, sheet with 3 mm dia
DSR-15 holes with stainless steel flange.
15.1 80 mm dia Each 1 4573 4573
15.2 100 mm dia Each 1 6450 6450
15.3 150 mm dia Each 1 10659 10659

BOQ for Fire Fighting Work Page 3 of 6

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Ref. No.
S. Amount Sch. Amount Non
DSR- Description Of Items Unit Qty Rate (Rs.)
No. (Rs.) Sch. (Rs.)
12/16
15.4 200 mm dia Each 1 22052 22052

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe

with 63 mm dia male and female couplings duly bound with
14
GI wire, rivets etc. conforming to IS 636 (type-A) as required :
DSR-16
14.1 16.1 Stainless Steel (Grade 304) Each 16 4434 70944

ELECTRIC Providing and fixing in position the industrial type pressure

AL DSR gauges with gun metal / brass valves complete as required
16 2018
16.8 Each 8 1094 8752

Supplying and Fixing First Aid Hose Reel, wall mounting

swinging type complete with drum & bracket of MS
17 construction, spray painted in Post office Red, confirming to
IS 884/1995 with upto date amendments, complete with the
DSR-17 following as required.
36 Meter long 20 mm dia water hose Thermoplastic (Textile
reinforced) Type - 2 as per IS : 12585
20 mm dia. ball valve & nozzle.
Drum and brackets for fixing the equipments on wall.
Connection from riser with 40 mm dia (Gun metal) stop valve
17.1
17.1 & M.S. Pipe. Each 8 10092 80736

Supplying and fixing Stainless Steel branch pipe with 20mm

dia nozzle conforming to IS:903. suitable for instantaneous
18.00
connections to hose pipe coupling etc. as required.
DSR-18
18.1 18.1 Stainless Steel (Grade 304) Each 16 1648 26368

Supplying and fixing of fire brigade connection of cast iron

body with gun metal male instantaneous inlet couplings
19 complete with cap and chain as reqd. for suitable dia MS pipe
connection conforming to IS 904 as required :
DSR-19
19.1 19.2 4 way - 150 mm dia M.S. Pipe Set 1 13822 13822

Supplying and fixing air vessel made of 250 mm dia, 8 mm

thick MS sheet, 1200 mm in height with air release valve on
top and flanged connection to riser, drain arrangement with
20
25 mm dia gun metal wheel valve with required accessories,
pressure gauge and paintingwith synthetic enamel paint of
DSR-20 approved shade as required. Nos 1 18009 18009

Providing, fixing, testing & commissioning of 15mm dia

21 quartzoid bulb type sprinklers of rating 68 degree centigrade
DSR-21 with required accessories :

21.2 21.2 Pendent/Upright Each 135 484 65340

21.3 21.3 Sidewall sprinkler Each 20 579 11580
21.4 ConcealedSprinkler Each 325 1394 453050

Providing & fixing of pressure switch in M.S. pipe line

22
DSR-22 including connection etc. as required. Each 2 1508 3016

Providing & fixing flow switch in following sizes M.S. pipe

23
DSR-23 including connection etc as required.
23.1 DSR-23.1 100 mm dia Each 8 7362 58896
23.2 DSR-23.2 150 mm dia Each 1 8869 8869
SITC of sprinkler installation valve

BOQ for Fire Fighting Work Page 4 of 6

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Ref. No.
S. Amount Sch. Amount Non
DSR- Description Of Items Unit Qty Rate (Rs.)
No. (Rs.) Sch. (Rs.)
12/16
Providing, fixing, testing & commissioning of installation
control valve of cast iron body, brass/bronze working parts
comprising of water motor alarm, bronze seat clapper,
clapper arm and hydraulically driven mechanical gong bell to
sound continuous alarm when the wet riser/sprinkler system
24 activates, pressure gauges, emergency releases, strainer,
pressure switch, cock valve complete with drain valve and
bypass, test control box, ball valves, MS pipe of required
size, flanges, orifice plate, gasket etc of follwing sizes as
required
DSR-24
24.1 24.3 150 mm dia Each 1 47898 47898

Supplying, installation, testing & commissioning of sprinkler

flexible pipe (UL Listed) of stainless steel complete with 15
NPT on reducer thread with maximum working pressure of
175 PSI test pressure of 875 PSI (Burst) with branch line
25
(Inlet) 25mm NPT male thread to sprinkler head (Outlet)
15mm NPT female thread with reducer, nipple, 2 side
brackets, center bracket, stockbar of following sizes complete
DSR-25 as required.
25.1 700 mm Nos 80 1341 107280
25.2 1000 mm Nos 70 1540 107800
25.1 25.3 1200 mm Nos 50 1633 81650
25.2 25.4 1500 mm Nos 40 1795 71800

Supplying and fixing fire hose cabinet fabricated from 16

gauge M.S. Sheet with single or double glazed front door
(with 4 mm thick glass) and locking arrangement, painted
28
fire red with stove enamelled paint "FIRE HOSE" written on
front including necessary supports approximate size.
2.2
28.1 a) a) 600x450x300 mm deep. Each 6 7902.18 47413.08367
Providing & fixing angle iron (40mm x 40mm x 5mm ) door
frame and MS sheet (2mm thick)
cum glass shutter of size 2.1 mtr x 1.2 mtr (N.S) with
25mm x 25mm x 3 mm angle frame all
around & stiffened in between i/c hinges, handle, locking
29.0
arrangement, painting with approved synthetic enamel
paint i/c sign writing on glass at internal hydrant including
providing & Fixing MS sheet 2mm thick on remaining
portion above door to close opening i/c painting etc as
2.3 required. Each 8 9511.88 76095.07256

Providing and fixing single C.I. suction collecting head as per

IS: 904-1983, hose coupling (draw out connection) with
30 female outlet as per 903 complete with 150 mm dia. G.I.
Suction pipe (with puddle flange) with a foot valve with
2.4 strainer complete as per drawings. Each 1 11414.26 11414.26088

Providing and fixing resilient rubber neoprene lined single

arch vibration eliminators suitable for raw water upto 45 deg.
32
C. temperature working pressure 7 kg/ sq.cm and test
2.5 pressure 14 kg/sq.cm.
32.1 a) 80mm dia Each 2 2670.35 5340.7034
32.2 b) 100mm dia Each 2 3277.94 6555.883174
32.3 c) 150 mm dia Each 2 4331.57 8663.131338

BOQ for Fire Fighting Work Page 5 of 6

 Construction of office building of Dental Council of India at Plot-14, Sector-IX, R.K.Puram, Near Sangam Cinema, New Delhi.

Ref. No.
S. Amount Sch. Amount Non
DSR- Description Of Items Unit Qty Rate (Rs.)
No. (Rs.) Sch. (Rs.)
12/16
Supplying, installation, testing and commissioning of
annunciation panel made out of not less 1.6 mm thick CRCA
sheet powder coated in approved colour with locking
arrangement, audio and visual indication of fault and
operation of automatic sprinkler, system monitoring including
providing and fixing the following i/c connections
interconnections etc. complete as required. The panel shall
be Micro-processor type/solid state type. Monitoring 16 Nos.
34
of flow switches. Monitoring the open circuit, short circuit and
earth fault in control cable between panel and flow switches.
Battery charger trickle cum boost to take complete load of
annunciation panel complete with indication of low Battery
voltage, mains failure and other accessories including
providing and fixing of 2 Nos. 12 volts 24 AH each sealed
maintenance free batteries and with audible alarm as reqd
2.6 Each 1 95118.84 95118.8407

Supplying and fixing of Fire Man's axe with heavy insulated

35
2.7 rubber as per standard conforming to IS 926. Each 8 731.68 5853.46712

TOTAL CARRIED TO SUMMARY (NON SCHEDULE ITEM) 3224028.00 278842.42

3.0 SUB HEAD - IV - (FIRE EXTINGUISHERS)

Supply , Installation of Mechanical Foam (AFFF) Fire

Extinguisher Stored pressure type ISI marked conforming to
IS: 15683. Capacity as mentioned below. Complete with
36 delivery hose, squeeze grip release valve, locking
arrangement, pressure gauge, operation manual and bracket.
Operating Temperature: 0ºC to + 55ºC.
3.1
36.1 a) Capacity 9 lit. Each 2 4543.75 9088
36.2 b) Capacity 45 lit.(Trolley mounted) Each 2 26340.60 52681

Supply , Installation of CO2 type Fire Extinguisher ISI marked

conforming to IS: 15683. Capacity 4.5 Kg. Complete with
37 delivery hose horn, wheel type release valve, locking
arrangement, operation manual and bracket. Operating
3.2 Temperature:- 30ºC to +55ºC. Each 9 15281.62 137535

Supply & Installation ABC dry powder Fire extinguisher ISI

Marked in 6 Kg Capacity confirming to IS: 15683-2006 duly
filled with ISI Marked Powder confirming to IS: 14609 with
39
squeeze grip release valve, discharge pipe, pressure gauge,
locking arrangement, operation manual and wall bracket.
3.3
39.1 a) Dry Chemical Powder ABC type of 6 Kg as per IS:15683 Each 9 3977.43 35797

TOTAL CARRIED TO SUMMARY (NON SCHEDULE ITEMS) 235100

BOQ for Fire Fighting Work Page 6 of 6