SS IE S C T UE R

M II T D YI S S YI CS UT R E E MZ ZS A

GameOver

I N SMANUALE
T A L L AT I O N
DI
AND
INSTALLAZIONE
P R O G R AE M M I N G
PROGRAMMAZIONE
MANUAL
 Installation and Programming Manual

INIM Electronics s.r.l. (Seller, Our, Us, ) warrants the original purchaser that this Warranty
product shall be free from defects in materials and workmanship under normal
use for a period of 24 months. As INIM Electronics s.r.l. does not install this
product directly, and due to the possibility that it may be used with other
equipment not approved by Us; INIM Electronics s.r.l. does not warrant against
loss of quality, degradation of performance of this product or actual damage that
results from the use of products, parts or other replaceable items (such as
consumables) that are neither made nor recommended by INIM Electronics.
Seller obligation and liability under this warranty is expressly limited to repairing
or replacing, at Seller's option, any product not meeting the specifications. In no
event shall INIM Electronics s.r.l. be liable to the purchaser or any other person
for any loss or damage whether direct ot indirect or consequential or incidental,
including without limitation, any damages for lost profits, stolen goods, or claims
by any other party caused by defective products or otherwise arising from the
incorrect or otherwise improper installation or use of this product.
This warranty applies only to defects in parts and workmanship relating to normal
use. It does not cover:
• damage arising from improper maintenance or negligence
• damage caused by fire, flood, wind or lightning
• vandalism
• fair wear and tear
INIM Electronics s.r.l. shall, at its option, repair or replace any defective products.
Improper use, that is, use for purposes other than those mentioned in this
manual will void the warranty. Contact Our authorized dealer, or visit our website
for further information regarding this warranty.

INIM Electronics s.r.l. shall not be liable to the purchaser or any other person for Limited
damage arising from improper storage, handling or use of this product.
Warranty
Installation of this Product must be carried out by qualified persons appointed by
INIM Electronics. Installation of this Product must be carried out in accordance
with Our instructions in the product manual.

The information contained in this document is the sole property of INIM Copyright
Electronics s.r.l. No part may be copied without written authorization from INIM
Electronics s.r.l.
All rights reserved.

Hereby INIM Electronics s.r.l. declares that the SmartLiving series of intrusion- European
control panels, the Air2 series of devices and the SmartLink product are in
compliance with the essential requirements and other relevant provisions of
Directive
Directive 1999/5/CE. compliance
Moreover, INIM Electronics s.r.l. also declares that all other devices mentioned in
this manual are in compliance with the essential requirements and other relevant
provisions of Directive 2004/108/CE.
The full declarations of conformity can be found at URL: www.inim.biz/dc.html.

The devices described in this manual, in accordance with the settings selected State-of-the-art
during the installation phase and the following illustrated guidelines are,
alternatively, in compliance with the the Italian Normative CEI 79-2:1998+Ab:2000
Installations
performance level 2 or European Normative CEI EN 50131-3:2009 (in reference to (DM 37/08)
Control and indicating equipment - intrusion control panels) and CEI EN 50131-
6:2008 (in reference to Power supplies) security grade 2.
In support of research, development, installation, testing, commissioning and
maintenance of intrusion alarm systems installed in buildings please refer to the
following normative documents:
CEI 79-3 e CEI CLC/TS 50131-7.
When installing INIM systems, it is up to the installer company to install systems
equipped with Normative CEI 79-2 compliant devices rather than devices
compliant with European Normatives series EN50131 within and not over the
DOWs summarized in amendment CEI 79-2;V1:2010.

2
Installation and Programming Manual

Table of
contents

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
European Directive compliance. . . . . . . . . . . . . . . . . . . . . . . . 2
State-of-the-art Installations (DM 37/08) . . . . . . . . . . . . . . . . 2
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . 5

0-1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
0-2 Graphic conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 1 General information . . . . . . . . . . . . . . . . . . . . . . . . . 6

1-1 Manufacturer's details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1-2 Description of the product and various models . . . . . . . . . . . . . . . . . 6
1-3 Patents Pending. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1-4 Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1-5 Operator Qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1-6 Conventions – Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 2 The Control panel and peripherals . . . . . . . . . . . . . . . 8

2-1 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2-2 SmartLiving intrusion control panels . . . . . . . . . . . . . . . . . . . . . . . . 8
2-3 Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3-1 Installing the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3-2 Connecting peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3-3 Addressing the peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3-4 Auto-enrolling peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3-5 Wiring and balancing alarm detectors. . . . . . . . . . . . . . . . . . . . . . . . 26
3-6 Wiring and balancing rollerblind/shock sensors . . . . . . . . . . . . . . . . . 28
3-7 Connecting wireless detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3-8 Learn Zone Balancing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3-9 Connecting the outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3-10 Attachment boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 4 First power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Chapter 5 Installation project via SmartLeague software . . . . . . . 34

5-1 The SmartLeague software application . . . . . . . . . . . . . . . . . . . . . . . 34
5-2 Using the software application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5-3 Creating a Project layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 6 Options and programming methods . . . . . . . . . . . . . . 37

6-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6-2 Programming from a keypad (Accessing the installer menu) . . . . . . . . 37
6-3 Programming via the SmartLeague software . . . . . . . . . . . . . . . . . . . 38
6-4 Panel options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3
 Installation and Programming Manual

6-5 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6-6 Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6-7 Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6-8 Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6-9 Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6-10 Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6-11 Partitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6-12 User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6-13 Installer codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6-14 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6-15 Arming scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6-16 Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6-17 Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6-18 Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6-19 Readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6-20 Sounderflashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6-21 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6-22 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6-23 Default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6-24 User functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6-25 Other parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Chapter 7 Errors and faults . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

7-1 Communication BUS (I-BUS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7-2 LED activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7-3 Ring Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Appendix A Technical terminology and Glossary . . . . . . . . . . . . . . 70

Appendix B Shortcuts at default . . . . . . . . . . . . . . . . . . . . . . . . . 78

Appendix C Available Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Appendix D Voice messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Appendix E Screw Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Appendix F Combination of outputs triggered by events . . . . . . . . 84

Appendix G Compliancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Appendix H Order Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

4
Installation and Programming Manual

ABOUT THIS
MANUAL

DCMIINE0SLIVINGE MANUAL CODE

3.00 VERSION

Terminology 0-1
The main supervisory unit and any constituent parts of the SmartLiving intrusion CONTROL PANEL, SYSTEM,
control system: APPARATUS

Directions as seen by the operator when directly in front of the mounted device: LEFT, RIGHT, BEHIND,
ABOVE, BELOW

A communicator device which sends voice calls or digital reports to programmed DIALER
contact numbers in the event of an alarm:

Persons whose training, expertise and knowledge of the products and laws QUALIFIED PERSONNEL
regarding security systems, are able to create, in accordance with the
requirements of the purchaser, the most suitable solution for the protected
premises.

Click on a specific item (from drop-down menu, options box, graphic object, SELECT
etc.).

Click on a video button, or push a key on the control panel keypad. PRESS

Graphic conventions 0-2

Following are the graphic conventions used in this manual.
Conventions Example Description
Indicates the title of a
Text in italics Refer to paragraph 4.3 chapter, section, paragraph,
Unpacking the device table or figure in this manual
or other published reference.
<text> #<AccountCode> Editable field
Reference relating to a part
[Uppercase letter] or
[number] [A] or [1] of the system or video
object.
BUTTON , , Keypads keys

The “Note” sections contain important information relating to the text. Note

The “Attention” prompts indicate that total or partial disregard of the procedure ATTENTION!
could damage the device or its peripherals.

The “DANGER” warnings indicate that total or partial disregard of the procedure DANGER!
could injure the operator or persons in the vicinity.

Similarly marked dialogue boxes contain recommendations and/or guidelines

which the manufacturer wishes to call attention to. Info

About this manual 5

 Installation and Programming Manual

Chapter 1

GENERAL
INFORMATION

Manufacturer's details 1-1

Manufacturer: INIM Electronics s.r.l.
Production plant: Via Fosso Antico - Centobuchi
63033 Monteprandone (AP) - Italy
Tel: +39 0735 705007
Fax: +39 0735 704912
e-mail: info@inim.biz
Web: www.inim.biz
Any persons authorized by the manufacturer to repair or replace the parts of this
system, hold authorization to work on INIM Electronics brand devices only.

Description of the product 1-2

and various models
Description: Intrusion control panel
Models: SmartLiving 505
SmartLiving 515
SmartLiving 1050
SmartLiving 1050L
SmartLiving 10100L
Year of manufacture: 2010

Patents Pending 1-3

The SmartLiving series of control panels employs the following INIM-patented
technologies.
• Input/Output Terminals: each terminal on-board the control panel, JOY
and nCode keypads and FLEX5 expansion boards can be configured as either
an input or output zone (Split terminal technology).
• nBy/X proximity reader: this reader has been especially designed to flush-
mount to all models of electrical light-switch backboxes.
• Learn zone balancing: this option allows the control panel to save the
balancing values of all the system zones automatically, thus eliminating the
tedious task of typing them in.

6 General information
Installation and Programming Manual

Manuals 1-4
Installation and 1-4-1
Programming Manual
(this manual)
This Manual can be obtained directly from the product manufacturer. You (the
installer) should read carefully through it and should be familiar with all the
components and operating procedures of the SmartLiving system. In order to
provide adequate protection, the installer must adhere to all the manufacturer's
guidelines relating to the active and passive security devices of this system. It is
the installer's responsibility to inform the system users that, regardless of its
capabilities, an intrusion alarm system is not a substitute for the necessary
precautions building occupants must take to prevent intrusion.

User's Manual 1-4-2

The installer should read carefully through the User's Manual (supplied with each
control panel). Once the system has been installed, you must ensure that the
User's Manual is available to the users for consultation, and that they fully
understand how the system works and are aware of all the functions, settings
and procedures.

Operator Qualifications 1-5

Installer 1-5-1
The installer is the person (or group of persons) who sets up and programs the
entire security system in accordance with the purchaser's requirements and in
respect of the safety laws in force. As the only individual in contact with system
users, it is the installer's responsibility to instruct them on how to use the
security system properly.
Under normal circumstances, the installer is not allowed to arm/disarm the
system without previous authorization from the user. All the system partitions
must be disarmed before accessing the parameter programming phase.

User 1-5-2
The users are the occupants of the building where this intrusion control panel is
installed. Only authorized users can operate the system.
The most common operations can be carried out without code/key verification.
This method must be expressly requested by the main user, as it considerably
lowers the security level of the system and may cause false alarms, accidental
arm/disarm operations, etc.

Conventions – Glossary 1-6

In order to help users understand the terminology utilized in this manual and
improve your knowledge of this system and its operating procedures, read
carefully through the Technical Terminology – Glossary (refer to Appendix A,
Technical terminology and Glossary).
The appendix contains the definitions of technical terms commonly used in the
field of security, therefore, relevant to the SmartLiving system.

General information 7
 Installation and Programming Manual

Chapter 2

THE CONTROL PANEL

AND PERIPHERALS

Environmental Conditions 2-1

All control panels from the SmartLiving series are for indoor installation only, and
operate best under the following conditions:
• Temperature: from -10° to +40°C
• Maximum humidity: 75% (without condensation)
The JOY/GR, JOY/MAX, FLEX5 and nBy/X keypads are for indoor installation only,
and operate best under the following conditions:
• Temperature: from -10° to +40°C
• Maximum humidity: 75% (without condensation)
The nBy/S reader is suitable for indoor or outdoor installation, and operates best
under the following conditions:
• Temperature: from -10° to +40°C
• Maximum humidity: 75% (without condensation)
• Protection grade: IP34

SmartLiving intrusion control 2-2

panels
Package contents 2-2-1
Inside the package you will find:
• Metal enclosure containing the motherboard and power supply (adapter or
switching power supply)
• User's Manual
• Quick Installation Guide
• Plastic bag containing the following:

Table 1: Package contents

505 515 1050 1050L 10100L
3k9W 1/4W Resistors 10 20
6k8W 1/4W Resistors 10 20
Security
Backup-battery wire 1
Screws to secure the
system
frontplate of the metal 4 protected
enclosure area
“INIM Electronics
security-protected area” 1
sticker

Items not included in the package:

Thermal probe (battery-charge optimizer which operates in accordance with the
battery temperature), backup battery, SmartLeague program CD, Installation
Manual. These devices are accessory items which must be purchased separately.

8 The Control panel and peripherals

Installation and Programming Manual

Control panel descriptions 2-2-2

Table 2: Control panels - electrical specifications and mechanical features
SmartLiving 505 SmartLiving 515 SmartLiving 1050 SmartLiving 1050L SmartLiving 10100L
Power supply voltage 230V ~ -15% +10% 50/60Hz
Max. current draw 0.2A 0.3A 0.6A
Max current. @ 12V 1.2A 3A 5A
Max. battery-charge
1A 2A
current
Backup battery 12V 7Ah 12V 17Ah
Max. current across 4.05A
900mA
+AUX terminals (1.35A per +AUX1, 1.35A per +AUX2, 1.35A per +AUX3)
Enclosure Dimensions
21.5 x 30.5 x 8.5 37.5 x 51 x 8.5
(W x H x D) cm
Weight (without
2.5 2.2 5.3
battery) Kg

The metal enclosures of SmartLiving 505, 515 and 1050 control panels provide
housing for backup batteries: 1 x 7Ah, max. dimensions 21.5 x 30.5 x 8.5 cm. 505 04/2010

The metal enclosures of SmartLiving 1050L and 10100L control panels provide Alimentazione / Power 230V~ -15% + 10%
50/60 Hz

LBDTIN4ASLIV05
Tension / Alimentacion
housing for backup batteries: 1 x 17Ah, max. dimensions 37.5 x 51 x 8.5 cm.
Consumo / Consumption
0.2 A
The control panel label (see figure opposite) is located inside the enclosure. Consommation / Consumo
MADE
Classe di Isolamento / Insulation class
The following table shows the maximum number of devices supported by the IN
ITALY Insulation class / Clase aislante I
various control panel models.

Table 3: Control panel - Main Features

SmartLiving intrusion control panels
515 04/2010
Alimentazione / Power 230V~ -15% + 10%
505 515 1050 1050L 10100L 50/60 Hz

LBDTIN4ASLIV15
Tension / Alimentacion
Total terminals 5 15 50 100 Consumo / Consumption
0.2 A
Consommation / Consumo
Terminals on panel 5 10 MADE
Classe di Isolamento / Insulation class
Terminals on panel IN
ITALY Insulation class / Clase aislante I
5 10
configurable as inputs
Terminals on panel
configurable as Rollerblind/ 2
Shock 1050 04/2010
Terminals on panel Alimentazione / Power 230V~ -15% + 10%
0 5 50/60 Hz

LBDTIN4ASLIV50
Tension / Alimentacion
configurable as outputs
Consumo / Consumption
Total zones 10 30 100 200 Consommation / Consumo
0.3 A
MADE
Outputs on panel motherboard 3 Classe di Isolamento / Insulation class
IN
ITALY Insulation class / Clase aislante I
Relay outputs on panel
1
motherboard
Open-collector outputs 2 2
(150mA) (500mA)
1050L 04/2010
Partitions 5 10 15 Alimentazione / Power 230V~ -15% + 10% LBDTIN4ASLIV50L
Keypads Tension / Alimentacion 50/60 Hz
5 10 15
(JOY, nCode/G, Concept/GN) Consumo / Consumption
0.3 A
Consommation / Consumo
Voice memo slots 5 10 15 MADE
Classe di Isolamento / Insulation class
FLEX5 Expansions 5 10 20 40
IN
ITALY Insulation class / Clase aislante I
nBy Readers 10 20 30
Transceivers
10 20 30
Air2-BS100
Digital keys and keyfobs 50 100 150
10100L 04/2010
Alimentazione / Power 230V~ -15% + 10%
LBDTIN4ASLIV100L

IB100 isolators 15 Tension / Alimentacion 50/60 Hz

Codes 30 50 100 Consumo / Consumption
0.6 A
Consommation / Consumo
Scenarios 30 MADE
Classe di Isolamento / Insulation class
Timer 10 20 IN
ITALY Insulation class / Clase aislante I
Recordable Events 500 1000

The SmartLiving control panels are not equipped with built-in dislodgement-tamper Note
microswitches. For the order code of this accessory item, refer to Appendix H, Order
Codes.

The Control panel and peripherals 9

 Installation and Programming Manual

SmartLiving 505/515 control-panel

Table 4: Control panels - description of parts
Model A1
505 515 1050 1050L 10100L
A 5A switching
Power Adaptor (Transformer) 3A switching power supply
power supply
B Mains connection terminal-board (230 Vac) - 50/60 Hz
C Power cable - “adaptor to control Power cable - “switching-power-supply to panel”
panel”
P
D Power cable - “switching-power-supply to panel”
E Mains cable entry
F Metal enclosure
Y
G Anchor-screw locations for the metal backbox
S

3.00
H Dislodgement-tamper microswitch location
I Backup battery
J Backup-battery wire Q
K Backup-battery connector X
L Thermal probe (accessory item)
M Thermal probe connector
R
N Thermal probe (enabled/disabled)
jumper
O Connectors for the SmartLAN power-supply jumper O
P Local I-BUS connector T
Q Service jumper connectors
R SmartLogos30M voice-board connector K
N U
S Control panel to PC serial cable connector
T Dislodgement-tamper microswitch connector (accessory item)
U Open-panel tamper microswitch connector (accessory item)
V
V Open-panel tamper microswitch W M
W Terminal board Control panel motherboard
X Blue and yellow activity LEDs SmartLiving1050/1050L/10100L
Y Firmware version label
A1
Z AUXREL32 board screw locations
A1 Ground connection screws
B1 FLEX5/U expansion board locations
C1 SmartLink board screw locations
D1 SmartLink antenna cable entries
E1 SmartLink board battery housing
P

Table 5: Control panel - terminal board

Icon/ Model Y
n. Identifier S
505 515 1050 1050L 10100L
3.00

1 Earth connection
2-3 Q
Internal telephone-line connection
4-5 PSTN Land-line connection (PSTN) X

6-7-8-9 +DS- I-BUS connection terminals

10-11-12 NO NC COM Voltage-free terminals of the relay output R
13 +AUX 12V ancillary power source terminal
14-15 OC1 OC2 Open-collector output terminals (x2)
16 +AUX 12V ancillary power source terminal
T
17-19-
Negative power terminals (Negative or GND)
21-23-25
18-20- T1-T2-T3- Screw terminals for control panel input terminals: T1, T2, T3, T4 and U
T5 V
22-24-26 T4-T5
27 +AUX 12V ancillary power source terminal
28-29 AC Transformer-power input O
terminals
28-30- T6-T7-T8- Screw terminals: T6, T7, T8, T9 and T10
32-34-36 T9-T10 of the control panel D
29-31- Negative power terminals (Negative or
33-35 GND)
37 +AUX 12V ancillary power source terminal
K
M
W

10 The Control panel and peripherals

Installation and Programming Manual

F F

G G G
B
A
A
C
B
E C E

L
L
H H
J
J

I I

G G

SmartLiving 505/515 SmartLiving 1050

G
G
Z
C

B1 B1 B

J
B1 B1

C1 E
C1

D1 L

C1
C1

E1

SmartLiving 10100L

The Control panel and peripherals 11

 Installation and Programming Manual

Peripherals 2-3
The control panel I-BUS accommodates the following peripherals:
• Keypads (JOY/GR, JOY/MAX, nCode/G, Concept/GN)
• Readers (nBy/S and nBy/X)
• Expansions (Flex5)
• Transceiver (Air2-BS100)
• Sounder/Flasher (Ivy)
• IB100 isolators

Joy/GR and Joy/MAX Keypads 2-3-1

JOY keypad motherboard I
Table 6: Device Specifications
JOY/GR JOY/MAX
Maximum Voltage [V] 16V
C
Typical current draw [mA] 70 90
Terminals configurable as OC outputs 2
F
Maximum current draw per terminal G
150
[mA]
Dimensions (W x H x D) [mm] 142 x 116 x 20 A
Weight [g] 160 180 H

Table 7: Joy - Description of parts E

A Terminal board
B Buzzer
C Microphone (Joy/MAX only) B D
D Temperature sensor (Joy/MAX only)
E Open-tamper microswitch JOY keypad backplate
F Backlit graphic display M
G Signaling LEDs
H Antenna (Joy/MAX only)
K K
I Speaker-wire connector (Joy/MAX only)
K
J Wire entry
K Wall-mount screw locations
L Speaker housing
N
M Board supports J K K
N Dislodgement-tamper microswitch screw location
O Dislodgement-tamper microswitch spring
L O
K
Keypad terminals: K
Table 8: Joy - Terminal board
n. Icon/ Description
Identifier M M
1 + Terminal “+” for the I-BUS connection
2 D Terminal “D” for the I-BUS connection
3 S Terminal “S” for the I-BUS connection
1 2 3 4 5 6 7 8

4 - Terminal “-” for the I-BUS connection

5 T1 Screw terminal of keypad terminal T1
6 Negative power terminal (Negative or GND)
7 T2 Screw terminal of keypad terminal T2 A
8 Negative power terminal (Negative or GND)

Terminals T1 and T2 can be configured as:

• Input (also as Rollerblind or Shock)
• Output
• Double zone
• Supervised Output
The keypad package contains a sticker (to be located under the keypad flip)
which can be used to note down the keypad address or label, its location, the
partitions it controls and phone-contact numbers.

12 The Control panel and peripherals

Installation and Programming Manual

nCode/G and Concept/G Keypads 2-3-2

Table 9: Device Specifications nCode/G keypad frontplate
nCode/G Concept/G
Maximum Voltage [V] 16V B
Typical current draw [mA] 70 80
Terminals configurable as OC outputs 1 A
Maximum current draw per terminal [mA] 150
Dimensions (W x H x D) [mm] 87 x 129 x 18
Weight [g] 135 155

Retro keypads
Table 10: nCode/G and Concept/G - nCode/G and Concept/G
Description of parts
A Backlit graphic display
B Signaling LEDs F
C Cable connector H
D Tamper microswitch
E Screw location D
F F
F Screw location
C
G Terminal board guide Concept/G keypad frontplate
H Buzzer

B
G G
Code/G and Concept/G keypads are equipped
with a buzzer and a T1 terminal which can be A
configured as:
• Input (also as Rollerblind or Shock) F F
• Output E
• Double zone

You can connect Code/G and Concept/G

keypads using the connector on the back of the Mounting bracket
device, via either the 6 wire cable (included), N
or the KB100 terminal board included in the
deep-bracket kit (accessory kit). L

Table 11: Brackets - Description of parts

N N
I Wire entry
L Wall-mount screw locations
M Flush-mount screw locations
M M KB100 - deep mounting bracket
N Backlocking grips
N

I
L
M M
N L N
N N

6 wire cable KB100 - terminal board M M

L L
I

M M
Table 12: Connection cables - KB100 terminal board N L N

Wire KB100
n. terminal Description
colour board
1 Red + Wire/Terminal “+” for the I-BUS connection
2 Yellow D Wire/Terminal “D” for the I-BUS connection
3 Green S Wire/Terminal “S” for the I-BUS connection
4 Black - Wire/Terminal “-” for the I-BUS connection
5 Blue T1 Wire/terminal of keypad terminal T1
6 Black Negative power wire/terminal (Negative or GND)

The Control panel and peripherals 13

 Installation and Programming Manual

Readers - nBy/S and nBy/X 2-3-3

nBy/S
B
Table 13: Device specifications
nBy/S nBy/X
Maximum Voltage [V] 16 C
Typical current draw [mA] 40 35
Dimensions (W x H x D) [mm] 64 x 80 x 17 19 x 50 x 51
Weight [g] 45 25
D

Table 14: nBy - Description of parts

A
A Terminal board
B Buzzer (nBy/S only) E
C LED 1 2 3 4
D Antenna nBy/X
E Optical sensors for open-enclosure and dislodgement tamper D

Reader terminals
Table 15: nBy - Terminal board
Icon/ C
n. Identifier Description

1 + Terminal “+” for the I-BUS connection A

2 D Terminal “D” for the I-BUS connection
3 S Terminal “S” for the I-BUS connection 1 2 3 4
4 - Terminal “-” for the I-BUS connection

Patent pending

Flex5 expansion boards 2-3-4

Flex5/

The Flex5 expansion board enclosure is available in two versions.

• Flex5/P comes in the enclosure shown above. This version can be set up to Flex5/U
monitor dislodgement and open-enclosure tamper by inserting a jumper into
connector [D], as shown.
• Flex5/U comes in an enclosure with on-view terminals and address DIP-
Switch, as shown opposite. It is evident that this version offers little protection
to the terminals. The jumper of connector [D] enables/disables protection
against open and dislodgement tamper of the plastic enclosure only.

Table 16: Device Specifications

FLEX5/P FLEX5/U
Maximum Voltage [V] 16
Typical current draw [mA] 30
Max. current across +AUX terminals
300
[mA @13.8V]
Dimensions with enclosure (W x H x D)
125 x 79 x 26 105 x 58 x 18
[mm]
Weight with enclosure [g] 103 66

14 The Control panel and peripherals

Installation and Programming Manual

The packages of both versions of the Flex5 expansion board contain:

• Flex5 expansion board in a plastic enclosure
• Dislodgement/Open tamper jumper
• 10 resistors @3K9W 1/4W
• 10 resistors @6K8W 1/4W B C E F
Table 17: Flex5 - Description of parts
A Terminal board
B Buzzer
C DIP-Switch strip for peripheral device addressing
D Connector to enable peripheral tamper detection D G

E Dislodgement tamper microswitch

F Open-tamper microswitch
G Peripheral activity LED (where present)

Peripheral activity LED signals are as follows:

• fast blinking - peripheral operative and enrolled (in configuration)
A
• slow blinking - peripheral operative but not enrolled
(not in configuration)
The Flex5 expansion board terminals are as follows:
Table 18: Expansion terminal board
Icon/
n. Identifier Description

1-2-3-4 +DS- I-BUS connection terminals

5-6 +AUX 12V ancillary power source terminals
7-9-11- T1-T2-T3- Screw terminals for expansion terminals: T1, T2, T3, T4
13-15 T4-T5 and T5
8-10-12-
Negative power terminals (Negative or GND)
14-16

Terminals T1, T2, T3, T4 and T5 can be configured as:

• Input (Rollerblind or Shock for terminals T1, T2, T3 and T4 only)
• Output
• Double zone
• Supervised Output

Transceiver for Air2-BS100 2-3-5

The Air2-BS100 two-way wireless system integrates directly with all models of the
INIM intrusion control panel range.
Description of the Air2 system devices:
• Air2–BS100 wireless transceiver module
• Air2–IR100 passive infrared detector
• Air2–MC100 magnetic contact/rollerblind/exit
• Air2–KF100 4 button remote-control keyfob
For a complete description of all these devices refer to the Air2-BS100
Installation Guide.

IVY Sounder/Flasher 2-3-6

The self-powered sounders from the IVY outdoor series are controlled
continuously by a microprocessor which monitors all the device parameters to
ensure performance and reliability at all times.
For a complete description of all these devices refer to the Sounder installation
manual.

IB100 isolators 2-3-7

Isolators from the IB100 series peripherals can be connected directly to the I-
BUS, in order to increase both its length and performance.
Each isolator has 4 input terminals and 4 output terminals for the BUS connection
with the following functions:
• Galvanic Isolation, up to 2500V, for the entire BUS between input and output.
• Regeneration of the communication signals.
• Detection of anomalies towards the output section and its consequent
isolation.
For a complete description of all these devices refer to the respective installation
manual.

The Control panel and peripherals 15

 Installation and Programming Manual

Chapter 3

INSTALLATION

Installing the control panel 3-1

Wall-mounting 3-1-1
The control panel should be located in a hidden place that can be accessed by
authorized building occupants only. D
1. Using the backbox (Table 4: Control panels - description of parts, G), mark
the anchor screw locations on the wall. Be sure not to drill in the vicinity of
electrical wiring or plumbing/gas pipes, etc.
2. Insert the screw anchors (recommended size 6mm).
3. Pull the wires through the wire sleeving.
4. Using the screws, attach the backbox to the wall.
5. Fit the dislodgement-tamper microswitch (provided with SmartLiving
1050L and 10100L, optional for SmartLiving 505, 515 and 1050, refer to A
Appendix H, Order Codes, TamperNO).
5.1. Insert the dislodgement-tamper bracket [A] into its location on the
backbox of the control panel (Table 4: Control panels - description of C
parts, H).
5.2. Using screw location [B], screw the bracket to the wall.
5.3. Connect the wire coming from the dislodgement-tamper microswitch [C] to B
the connector [D] on the board (Table 4: Control panels - description of
parts, T).

The sleeving must be flame class rating V-1 or higher. Note

Connecting the Mains 3-1-2

power supply
The control panel must be powered through a separate line coming from the
Mains box. The line must be protected by a safety standards compliant circuit
breaker (trip switch).
The circuit breaker (trip switch) must be located externally to the apparatus and
should be easily accessible. The distance between contacts must be at least
3mm. The manufacturer strongly advises the use of a magnetothermic switch
with C intervention curve and nominal (maximum) current - 16A.
The protective earthing system must be compliant with all safety standards and
laws in force.
Ensure that the Mains is switched Off during the mains connection phase. Danger DANGER!
of electric shock.

The 505 and 515 models

A SmartLiving 505/515
Pull the mains (primary power-supply) cable through the cable entry [B], then
complete the (Mains) connections on the mains terminal board [A]. When C
connecting the earth wire, follow the indications on the label [C] located near the
L
MAIN FUSE T500mA L250V
AC Input

mains terminal board. The transformer (located above the PCB) and switching
power supply (housed inside the control panel enclosure) provide the power B E F
C
N

source to the entire system and supply the charge voltage to the backup battery.
The 1050, 1050L and 10100L models
Pull the cable through the cable entry [E], then connect the mains power to the
power-supply terminal board [D], located on the backplate above the
motherboard. When connecting the earth wire, follow the indications on the
power-supply label [F]. The power-supply provides power to the system and
supplies the charge voltage.

16 Installation
Installation and Programming Manual

AC Input AC Input
230V ~ 50/60 Hz 230V ~ 50/60 Hz

D F L N F A N L F
B

L
230V ~ 50/60 Hz
D D

AC Input
N
E

E E

SmartLiving 1050 SmartLiving1050L SmartLiving10100L

Connecting the backup battery 3-1-3

The backup battery [A] connection must be completed during the phase
described in Chapter 4 - First power up.
The SmartLiving 505, 515 and 1050 control panels house one lead battery @12V
7Ah.
The SmartLiving 1050L and 10100L house two lead batteries, one @12V 17Ah
and the other @12V 1.2Ah.

The battery casing must have HB flame rating or higher. Note

Using the battery wire [B] (included), connect the battery directly to the control
panel motherboard.

Ensure that battery polarity is correct: ATTENTION!

- black wire = negative
- red wire = positive

The backup battery is the secondary power source which powers the system
during mains failure (230Vac, 50Hz).
Once powered up, the panel will charge and monitor the batteries automatically.
The panel tests the efficiency of the batteries by simulating load current demand
at regular 4 minute intervals. Faults
If the battery fails to meet the demand, the system will generate a “Low Battery”
Low battery
fault.
This fault will be signaled on the yellow LED on the keypads. To view the event
details, work through the following steps:
Type-in Code (User) , View , Faults .

SmartLiving 505/515 SmartLiving 1050 SmartLiving10100L

D
D

D
C B
C
B C
B

A
A A

E E
E

Installation 17
 Installation and Programming Manual

Thermal probe 3-1-4

The battery charge process can be optimized by means of a thermal probe [C]
(accessory item). This device regulates the charging process in accordance with
the battery temperature. The thermal probe protects against battery overheating
and consequent permanent damage to the battery.
To connect a thermal probe, work through the following steps.
1. Disconnect the battery (if necessary).
2. Connect the thermal probe to the connector on the board [D]. If you are
installing a model which is equipped with a switching power supply (Smart- 3A switching power supply
Living 1050, 1050L and 10100L), you can connect the thermal probe
directly to the power supply connector.
3. If you are installing a SmartLiving505 or 515 model, remove the jumper on
the motherboard to enable the thermal probe (refer to Table 4: Control
panels - description of parts, N).
4. Using adhesive-insulating tape, attach the thermal probe to the battery
[E], in such way as to provide optimized heat-transfer measurements.
5. Hold a thermometer against the probe, and measure the probe tempera-
ture.
6. Using the following graph, find the value the measurement will be based
on. F

14,5
Volt
14,25

14 5A switching power supply

13,75
F

13,5

13,25

13

12,75
0 5 10 15 20 25 30 35 40 45 50 °C

7. Using a tester, measure the voltage on the +AUX terminals and adjust the
trimmer [F] to the previously measured value.

Opening and closing the 3-1-5

control panel
If you wish to remove the metal frontplate, work carefully through the following
steps.

1. Type-in the installer code and press . Access to the installer menu inhib-
its the alarm outputs and dialer automatically, therefore, the system will be
unable to generate alarms or event calls.
2. Remove the four screws and the metal-frontplate.
3. Insert the Service jumper (refer to paragraph 3-1-9 Maintenance status)
and carry out the necessary work.
Once your task is complete, work carefully through the following steps.
1. Remove the Service jumper.
2. Using the 4 screws, secure the frontplate to the backbox.
3. Exit the installer menu.

If you exit the Installer menu before replacing the panel frontplate, the system panel will Note
not generate an “Open-panel” event.
However, the system will generate an “OpenPanel” event, if the frontplate is not replaced
within 15 seconds of closing the open-tamper microswitch.

Land-line connection (PSTN) 3-1-6

Terminals 4 and 5 on the control panel motherboard (Table 5: Control panel -
terminal board, 4-5) are for the land-line telephone connection.
If you are installing the system in a place where the land line (PSTN) service is
not available, or if you wish to increase the level of security of the system, these

18 Installation
Installation and Programming Manual

terminals also accept a GSM interface (such as Inim's SMARTLINK) which

simulates the analogue land-line.
Inim manufactures two versions of the SMARTLINK GSM Interface: SMARTLINKG Control
and SMARTLINKGP. Both these devices simulate the analogue land line during
panel
line-down conditions (line trouble or wire-cutting) and allow the control panel to
switch incoming/outgoing calls to the GSM network.
You can also use the terminals on the SmartLink board to extend the functions
provided by the SmartLiving system. The following section describes several
methods which will allow you to provide users with advanced functions.
Arming/Disarming the system over-the-phone using a cost-free

SmartLink
call or SMS text
If you connect one of the SmartLiving board terminals, which is configured as a
“follow zone”, to an output on the SmartLink board, users will be able to arm or
disarm (“ARM ON” or “DISARM OFF”) the SmartLiving system by sending an SMS
text (refer to paragraph 3.12 in the SmartLink programming manual).
In a similar way, using a “switch zone”, users will be able to arm or disarm the
system by calling the control panel (refer to “Caller ID” in paragraph 3.9 in the
SmartLink programming manual).
Alarm warning to users via SMS text
If you connect one of the control-panel alarm outputs to an input on the
SmartLink board, the system will be able to send users alarm warnings via SMS
text (refer to paragraph 3.10 in the SmartLink programming manual). The
system can be set up to send an editable SMS text to 10 different contact
numbers.
All the functions of the SmartLiving system which use the land line (voice dialer,
answerphone, report communications and teleservice) can be managed
completely over the GSM network by the SmartLink. The SmartLink will also allow
you to carry out teleservice maintenance over the GSM network.

If there are ADSL filters on the line, it will be necessary to connect the control panel Note
downstream of the filters, to the line dedicated to telephone equipment (this line is clearly
indicated on the filters).

Connecting to a PC 3-1-7
The control panel can be programmed from a PC by means of the SmartLeague
software application (refer to paragraph 6-3 Programming via the SmartLeague
software) and an RS232 serial cable.
Insert the RS232 serial link (accessory item) into the connector [A], as shown in
the figure opposite.
If you wish to purchase an RS232 serial link, refer to the codes in Appendix H, Order
Codes. If your PC is not equipped with an RS232 port, but has a USB instead, you can
use INIM's Approved RS232-USB adaptor (accessory item).
SmartLiving end PC end
DB9F connector DB9F connector
2 3
3 2
4 4 A
1 9
5 5
9 1
6 6
7 7
8 8
B
SmartLiving end PC end
DB9F connector DB25F connector
2 2
3 3 25
1 4 20
5 7
9
6 6
7 4
1
8 5

Installation 19
 Installation and Programming Manual

Connecting the SmartLogos30M 3-1-8

voice board (accessory item)
The SmartLogos30M voice board provides the SmartLiving system with an array
of useful voice functions.
For proper installation of the board, work carefully through the following steps.
1. Disconnect all power sources to the control panel (mains and lead batter-
ies).
2. Connect the board to the respective connector [B].
3. Power up the system from the mains and reconnect the lead batteries.

Maintenance status 3-1-9

There are two distinct positions for the Service jumper (Table 4: Control panels -
description of parts, Q):
1. “RUN” (control panel operating normally)
2. “SERV” (control panel ready for maintenance work)
The keypads indicate maintenance status (jumper in “SERV” position) by showing
the “Maintenance” message on the first line on the display next to the keypad
address. The address of the built-in reader (if enabled) of JOY/MAX keypads will
also be shown.
Under these circumstances, the control panel:
• Forces the relay output on the motherboard (Table 5: Control panel - terminal
board, 10-11-12) to standby status. Position 1 Position 2
• Does not activate the outputs (and will force to standby any active outputs)
triggered by:
•• alarm or zone/partition tamper
Maintenance K03
•• peripheral tamper P05
•• open/dislodged panel tamper DASIDASI--
• It allows initialization of the keypad address programming phase.
• It allows initialization of the reader address programming phase.
• It initializes automatically the auto-enrolment of the peripherals connected to Keypad address
the BUS at 10 seconds intervals. It allows assignment of the addresses to the
peripherals connected to the BUS and, at 10 second intervals, enrolls the Reader address
peripherals it finds.
• The control panel will not reset the BUS in an attempt to retrieve peripherals
in the event of peripheral loss.
• It will continue to operate as normal, except under the aforesaid
circumstances.

20 Installation
Installation and Programming Manual

Connecting peripherals 3-2

The I-BUS line wiring 3-2-1
The SmartLiving peripherals (keypads, readers, expansions, sounder/flashers,
transceivers and isolators) must be connected to the control panel via the I-BUS.
The wiring diagram opposite provides an example of a 4-wire connection (using
shielded cable) between a control panel and its peripherals.
The cable specifications depend on the length of the BUS (from the panel
terminals to the most distant point), Baud rate and the load current draw.

Table 19: Recommended cable

Cable Section I-BUS
n. wires
AF CEI 20-22 II (mm2) terminal
4 wire cable + 2 0.5 + -
shield 2 0.22 D S
2 0.5 + -
6 wire cable +
shield 2 0.22 D S
2 0.22 available
2 0.75 + -
6 wire cable +
shield 2 0.22 D S
2 0.22 available

The maximum wire length of the I-BUS depends on the deployment of the
peripherals connected to the line and their specific current draw (in particular the
keypads and expansion boards). The power to peripherals and detectors can be
supplied by external power stations or by the line itself.
Furthermore, the speed of the communication BUS (Baud rate) can be modified
by means of the SmartLeague programming software. If the BUS is not used to
power the peripherals and their loads, the maximum wire length is 300 meters @
250kbs, regardless of the number of peripherals involved.
An intermediate speed (125kbs) can support a single section of 700 meters.
Shield + D S -

The shield must be connected to one of the terminals (Negative or GND) at ATTENTION!
the control panel end only, and must run along the BUS without being connected
to negative or GND at any other point.

If you wish to increase the length and performance of the BUS, you can connect
IB100 isolators .
If the speed of the communication BUS (Baud rate) is low (38.4 or 125 kbps),
you can apply a maximum of 5 isolators in a cascade connection.
If the speed of the communication BUS (Baud rate) is high (250 or 2 kbps), you
can apply a maximum of 2 isolators in a cascade connection.
You can connect up to 15 isolators in all.
It is extremely important to evaluate correctly the number of isolators connected ATTENTION!
in cascade to the BUS.

The following example will help you achieve a correct evaluation:

Control panel
IB100 IB100

IB100

IB100 IB100

BUS sections: BUS sections: BUS sections:

1 isolator in cascade 2 isolators in 3 isolators in
connection cascade connection cascade connection

Installation 21
 Installation and Programming Manual

Installing JOY keypads 3-2-2

E
1. Remove the keypad from its package.
2. Detach the down-flip and cover from the backplate.
D
3. Remove the board from the backplate. Be careful not to damage the dis-
lodgement-tamper spring ([A]) during this operation.
B B
4. Mark the chosen anchor-screw locations [B] on the wall. Use at least 2 of
the 7 locations available. Drill the anchor-screw holes (ensure that you do C
not drill in the vicinity of electrical wiring or plumbing). Pull the BUS and
terminal connection wires through the wire entry [C] and attach the back-
A
plate securely to the wall.
5. Using the screw, fasten the dislodgement-tamper bracket into its screw B
location [D].
6. For JOY/MAX only: Plug the speaker connector [E] into the keypad circuit,
ensure that polarity is correct (black wire to the right [F] and red wire to
the left [G]). Be careful not to damage the connector during this operation.
If it becomes necessary to separate the connector from the speaker, use a
small screwdriver or similar tool to disengage it. DO NOT pull the connector
out by the wires.

J
G
F E

7. Place the circuit on the two lower supports [H] and, after aligning it with
the other supports [I], push the back-locking grip [J] slightly outwards
until it clicks closed. Be careful not to damage the dislodgement-tamper
spring [A].
8. Replace the cover and down-flip. If necessary, secure the two screws into H
their screw locations on the bottom part of the cover.

Installing nCode/G and 3-2-3

Concept/G keypads
1. Connecting the device to the system
2. Pull the connection wires through the wire entry [A].
3. Connect the cables to the connector on the keypad backplate [B]. If you
are using the connector provided with the KB100 kit [C], connect the wires
to the terminals, in accordance with the instructions described in para-
graph 2-3-2 nCode/G and Concept/G Keypads, then insert the connector
into the guide [D] until it locks into place. B
4. Using at least 2 screws, mount the bracket to the wall.
5. Using the back-locking grips, attach the keypad to the bracket (as shown in
figure [E].
6. Fasten the screw [F] (included) into the screw location [G], to secure the
keypad properly to the bracket.

D
E

22 Installation
Installation and Programming Manual

Installing nBy/S Readers 3-2-4

The wall-mount nBy/S reader is suitable for indoor and outdoor installation.
Insert the two anchor screws [A] (included) into the two screw locations [B] on
the plastic backplate.

C B

In order to avoid the risk of piercing the silicone seal [C], and thus jeopardizing ATTENTION!
the waterproofing of the enclosure, insert the screws before fitting the seal.

Installing nBy/S readers 3-2-5

The Universal flush-mount nBy/X (Patent Pending) has been especially
designed to integrate with all brands of cover plates [A]. Drill two holes [B] for
the light guide [C].
Use the adhesive drill-pattern (see opposite) to mark the drilling locations
accurately.
1. Ensure that the centre of the cover plate coincides with the crossing of the
axes x and y on the drill-pattern. In this way, the two drilling locations (1 x
7mm diameter and 1 x 8mm diameter) will be positioned precisely.
2. Using the screw [D], secure the reader components inside the cover plate.
3. Insert the cover plate (with the reader already assembled) into the light
switch box.
A
C

Dislodgement tamper
The nBy/X reader is not equipped with built-in dislodgement-tamper protection.
However, the following section describes how you can protect nBy/X reader
against this kind of tamper.
In order to comply with Italian certification (Level 2 - IMQ Security Systems), all
the system peripherals must be protected against tamper. Installation of a
microswitch will allow the reader to signal tamper events. To obtain this type of C
D A
protection, work carefully through the following steps.
1. Use a microswitch with at least two normally-open contacts [A]. The one
shown in figure 3 has 3 contacts: COM-NO-NC.
2. Configure one of the terminals as follows: Input; 24H; Description =
“Tamper reader x”; single balancing with 6K8W [resistance [B]; unlimited B
alarm cycles. Assign the duly programmed terminal to at least one keypad
partition.
3. Using 2 wires, connect the microswitch to the 24H input terminal.
4. On the microswitch:
4.1. using one of the two wires, connect the common contact (COM) to the
GND terminal of the 24H terminal [C].
4.2. Connect the normally-open contact (NO) to one end of the 6k8W
resistance [D] (the normally-open contact generates a short-circuit
between itself and the COM contact when the microswitch-lever is

Installation 23
 Installation and Programming Manual

compressed). Connect the other end of the resistance to the wire

which is connected to the 24h input terminal.
5. Install the microswitch as shown in the previous figure, so that the switch
lever is compressed. If an unauthorized attempt to dismantle the nBy/X
reader occurs, the lever will expand in order to open the contact which trig-
gers instant alarms on the 24H terminal.

This wiring method can be applied in most situations, however, it is only a point of Note
reference. In order to ensure proper protection, you must always take in to account the
specific mechanical and electrical conditions of the device you are working on.

Addressing the peripherals 3-3

In order to allow the control panel to identify the peripherals distinctly, you must
assign a different address to each device. However, you can assign the same
address to two devices which belong to different categories (e.g. a Flex5
expansion and a JOY keypad) as, in this case, the control panels will see them as
two distinct devices.
Expansion -
Transceiver DIP-switch Reader nBy/S nBy/X Keypad
Red Blue Green Yellow
address address address
1 00000000 1 0 0 0 1
SmartLiving515 SmartLiving505

1
2 00000001 2 0 0 1 0
3 00000010 3 0 0 1 1
SmartLiving505 and 515

2
4 00000011 4 0 1 0 0
5 00000100 5 0 1 0 1
3
6 00000101 6 0 1 1 0
7 00000110 7 0 1 1 1
4
8 00000111 8 1 0 0 0
9 00001000 9 1 0 0 1
5
10 00001001 10 1 0 1 0
11 00001010 11 1 0 1 1
6
12 00001011 12 1 1 0 0
SmartLiving1050 and 1050L
SmartLiving1050 and 1050L

13 00001100 13 1 1 0 1
7
14 00001101 14 1 1 1 0
15 00001110 15 1 1 1 1
8
16 00001111 16 0 0 0 L
17 00010000 17 0 0 L 0
9
18 00010001 18 0 0 L L
19 00010010 19 0 L 0 0
10
20 00010011 20 0 L 0 L
21 00010100 21 0 L L 0
11
22 00010101 22 0 L L L
23 00010110 23 L 0 0 0
12
24 00010111 24 L 0 0 L
SmartLiving10100L

25 00011000 25 L 0 L 0
13
26 00011001 26 L 0 L L
27 00011010 27 L L 0 0
14
28 00011011 28 L L 0 L
29 00011100 29 L L L 0
15
30 00011101 30 L L L L
31 00011110
32 00011111 0 LED OFF
33 00100000 1 LED ON
34 00100001 L LED blinking
35 00100010
SmartLiving10100L

36 00100011
37 00100100
38 00100101
39 00100110
40 00100111

You must not exceed the maximum number of addresses allowed for each type of
peripheral. The following table shows the available peripheral addresses and the
maximum number of addresses accepted.
The top left section of the Table shows the maximum number of addresses (5 for
the SmartLiving505 model, 10 for the515 model, 20 for the 1050 model and 40
for the 10100 model) and the DIP-switch configuration of the Flex5 expansion
board and Air2-BS100 transceiver (refer to paragraph 3-3-2 Addressing FLEX5
expansions and the Air2-BS100 transceiver).
The second section shows the nBy/S and nBy/X reader addresses with the
corresponding combination of the reader LEDs (refer to paragraph 3-3-3
Addressing nBy readers).

24 Installation
Installation and Programming Manual

The section on the far right shows the addresses available for the keypads (refer
to paragraph 3-3-1 Addressing the keypads).
For the Ivy sounderflasher and IB100 isolator addressing procedure, refer to the
respective Installation Guides.

Addressing the keypads 3-3-1

Work carefully through the following steps.
1. Put the control panel in “Maintenance” mode by inserting the respective keypad address
jumper (Table 4: Control panels - description of parts, Q). _1
2. Using the keypad you wish to address, press and release keys and Min. 01
Max. 30
simultaneously; set the address then press (if the keypad
firmware version is 1.02 or higher, go to point 5).
3. For JOY/MAX only: enable or disable the reader press keys or .
4. For JOY/MAX only: if the reader is enabled, assign the address and press
.
5. If the keypad firmware version is 1.02 or higher, enable or disable the dis-
lodgement tamper protection by pressing or .
6. If the keypad firmware version is 1.08 or higher, enable or disable the dis-
lodgement tamper protection by pressing or .

For security reasons, if the address is not assigned within 30 minutes of accessing Note
“Maintenance” mode (SERV jumper inserted), the keypad will exit the programming phase
automatically.
If this occurs and you wish to restart the programming phase, remove and re-insert the
jumper.
The same procedure is necessary when you re-address the keypad.

Addressing FLEX5 expansions and the 3-3-2

Air2-BS100 transceiver
Using a small screwdriver or similar tool, set the expansion board address on the
8-segment DIP-Switch strip (Table 17: Flex5 - Description of parts, C). Each
segment can be set at “1” (On) or “0” (Off).
The figure shows some examples.

ON Expansion n. 1

1 2 3 4 5 6 7 8

ON Expansion n.29

1 2 3 4 5 6 7 8

ON Expansion n.40 ON
Position 1
Position 2
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

Addressing nBy readers 3-3-3

To assign addresses to the system readers, work carefully through the following
steps. This procedure does
not apply to the built-in
1. Put the control panel in “Maintenance” mode by inserting the respective
readers of JOY/MAX
jumper (Table 4: Control panels - description of parts, Q).
keypads.
2. Start the “Address Programming” phase using the software or from a key-
pad:

Type-in Code (Installer PIN) , PROGRAMMING Readers , Prog. address .

3. Each reader indicates its own address on its LEDs (refer to the Table in
paragraph 3-3 Addressing the peripherals).
4. Hold a valid key in the vicinity of the reader. The reader will run through a
series of available reader-addresses (an address every 2 seconds).
Remove the key when the LEDs indicate the desired address.

Installation 25
 Installation and Programming Manual

5. The reader will hold the addressing phase for a further 10 seconds, in order
to allow you to change the address if necessary.
6. The reader will assign the selected address when the 10 second period
expires.
7. If you wish to assign an address to another reader, hold a valid key in the
vicinity of the reader and work through points 4 to 6.
8. End the reader-address programming phase (exit “Prog. address” via key-
pad, or click on “Stop reader address setup”, if you are using the Smart-
League software).

Auto-enrolling peripherals 3-4

The peripherals connected to the BUS are enrolled automatically in the following
situations:
• on first startup (refer to Chapter 4 - First power up)
• if the SERV jumper is inserted (refer to paragraph 3-1-9 Maintenance status)
• via the Installer menu (refer to paragraph 6-23 Default settings) >
Type in Code (Installer) , PROGRAMMING Default settings , Auto Periph .

Wiring and balancing 3-5

alarm detectors
The wiring and respective balancing method depend on the type of detector you
are installing, and the level of protection you wish to achieve. The detectors can Red
White Gold
be powered through:
Orange
• terminals [+AUX/12V] and [-/GND] on the control panel
• terminals [+AUX/12V] and [-/GND] on FLEX5 expansions 3K9Ω 1/4W
• terminal [+/12V] and terminals [-/GND] on keypads
• from any 12V ancillary source on condition that its GND reference is in Red
common with that of the control panel. Grey Gold
The resistors used for balancing are: Blue
•• 3K9W 1/4W
6K8Ω 1/4W
•• 6K8W 1/4W
The following Table indicates the protection level of each detector type and the
balancing options provided by the control panel:
Table 20: Protection level
(*) Single balancing provides
Double
Double the same level of protection as
BALANCING N.O. N.C. Single Double zone zone
with EOL Double balancing, when the
Infrared or tamper contact of the detector
medium
Double very low low high medium high is connected to a
(*)
technology balanced zone on the
Magnetic contact very low low medium medium high control panel.

N.C./N.O. Balancing 3-5-1

For N.C. (normally closed) and N.O. balancing (normally open), it is
possible to detect two distinct zone conditions:
• standby
• alarm
For each of these, the control panel reads different resistance values on
the terminal, expressed below in Ohm.

W N.C. N.O.
> 2 x 3900 + 6800 alarm standby
> 2 x 3900 + 6800 alarm standby
3900 + 6800 alarm alarm
2 x 3900 alarm alarm
+12V GND Alarm Tamper

3900 standby alarm

0 standby alarm

If you wish the detector to signal tamper events, connect the detector
“Tamper” terminal to a “24h” zone on the control panel.

26 Installation
Installation and Programming Manual

Single balancing 3-5-2

Single zones can discriminate 3 conditions on the entire terminal:
• standby
• alarm
• tamper (short-circuit)
For each of these, the control panel reads different resistance values on
the terminal, expressed below in Ohm.

W Zone
> 6800 alarm 6K8W 1/4W
6800 standby
0 tamper

+12V GND Alarm Tamper

If you wish the detector to signal tamper events, connect the detector
“Tamper” terminal to a “24h” zone on the control panel.

Double balancing 3-5-3

Double balancing discriminates 4 distinct conditions on the zone terminal:
• standby
• alarm
• tamper (short-circuit)
• tamper (wire cutting)
For each of these, the control panel reads different resistance values on
the terminal, expressed below in Ohm.

W Zone 6K8W 1/4W

> 6800 tamper (wire cutting)
6800 alarm
+12V GND Alarm Tamper

6800 / 2 standby
0 tamper (short-circuit)

Double-Zone Balancing 3-5-4

Double zones without EOL resistor can discriminate 5 conditions on the
entire terminal:
• standby on both zones
• alarm on zone 1 and standby on zone 2
• alarm on zone 2 and standby on zone 1
• alarm on both zones
• tamper (wire cutting)
W 1/4W
3K9W
For each of these, the control panel reads different resistance values on Zone 1
the terminal, expressed below in Ohm.
+12V GND Alarm Tamper

Zone 2
W Zone 1 (double)
> 3900 + 6800 tamper
3900 + 6800 alarm alarm
6800 standby alarm
3900 alarm standby
0 standby standby 6K8W 1/4W
Zone 2
+12V GND Alarm Tamper

Installation 27
 Installation and Programming Manual

Double Zone Balancing with EOL 3-5-5

Double zones with EOL resistors can discriminate 6 conditions on the
entire terminal:
• standby on both zones
• alarm on zone 1 and standby on zone 2
• alarm on zone 2 and standby on zone 1
• alarm on both zones
• tamper (wire cutting)
• tamper (short-circuit) Zone 1
For each of these, the control panel reads different resistance values on

+12V GND Alarm Tamper

the terminal, expressed below in Ohm.

Zone 2
W Zone 1
(double)
> 2 x 3900 + 6800 tamper (wire cutting)
> 2 x 3900 + 6800 alarm alarm
3900 + 6800 standby alarm 3K9W 1/4W
2 x 3900 alarm standby
3900 standby standby 6K8W 1/4W
Zone 2
0 tamper (short-circuit)

+12V GND Alarm Tamper

Wiring and balancing 3-6
rollerblind/shock sensors
It is possible to choose between two types of balancing for Rollerblind and Shock
sensors:
• Normally Closed (N.C.)
• Single balancing (NC with EOL)
The following table compares the protection level of rollerblind/shock sensors
using the two balancing options provided by the control panel.

Table 21: Protection level

Single balancing
BALANCING N.C.
(N.C. with EOL)
Rollerblind
very low high
or Shock

If the rollerblind or shock sensor is connected to a terminal of a wireless device,

the connection cable must be less than 2 meters long.
The rollerblind sensor must generate pulses with a length of between 500msec
and 10msec.

Normally Closed (N.C.) 3-6-1

In this case, the alarm condition is revealed exclusively by the number of pulses
(pulse count) the control panel detects on the terminal.
If this balancing method is applied, the control panel will be unable to detect
tamper, wire-cutting or short-circuit.
The discriminated conditions are:
• standby
• alarm
The alarm condition is triggered by the number of pulses and sensitivity, in
accordance with the programmed parameters (refer to paragraph 6-6 Zones -
Detector type).

28 Installation
Installation and Programming Manual

Single balancing 3-6-2

(N.C. with EOL)
In this case, the discriminated conditions are:
• standby
• alarm
• tamper (wire cutting)
• tamper (short-circuit)
For each of these, the control panel reads different resistance values on the
terminal, expressed below in Ohm.

W Zone
> 3900 / 2 tamper (wire cutting)
3900 / 2 standby
0 tamper (short-circuit)
The alarm condition is triggered by the number of pulses and sensitivity, in
accordance with the programmed parameters (refer to paragraph 6-6 Zones -
Rollerblind/Shock).

W 1/4W
3K9W

Connecting wireless 3-7

detectors

CR123A 3V
Switching

For the connection and deployment of wireless detectors (Air2-IR100 and Air2-
MC100), refer to the Air2-BS100 Installation Guide.

-
For the connection and balancing of detectors connected to terminals “T1” and
“T2” of the Air2-MC100 device, refer to paragraphs 3-5-1, 3-5-2, 3-5-3, 3-6-1
and 3-6-2. Air2-
It is necessary for the “GND” terminal of the Air2-MC100 device to be connected MC100
to GND (Negative) of the power source of the detector connected to terminals
“T1” or “T2”.

Detector
+12V GND Alarm T

Learn Zone Balancing 3-8

Once you have completed the wiring and configured the balancing of all the zones,
you can instruct the control panel to save all the related parameters automatically, by Patent pending
activating the Learn zone bal. option (refer to paragraph 6-23 Default settings, Learn
zone bal.).

Connecting the outputs 3-9

It is possible to set up the outputs to activate in response to the events the
control panel manages.
For the connection of the outputs to terminals “T1” and “T2” of the Air2-MC100
device, refer to the Air2-BS100 Installation Guide.

Connecting the sounders 3-9-1

In the event of intrusion alarm, the control panel activates the output/s which are
connected to the audible/visual signaling devices. The relay output on the control
panel motherboard is the alarm output which is most commonly used to drive a
self-powered sounder.
The following wiring diagram shows the connection of a self-powered sounder
(IVY manufactured by INIM) and an indoor sounder.

Installation 29
 Installation and Programming Manual

Control Self-powered
panel sounderflasher

Indoor
sounderflasher

Connecting open- 3-9-2

collector outputs
All the system outputs, except for the relay output on the control panel
motherboard, are open-collector outputs. as follows:
• OC1 and OC2 are open-collector outputs that sink maximum currents in
accordance with the Table 3: Control panel - Main Features.
• All the terminals configurable as outputs are open-collector outputs that sink a
maximum current of 150 mA.
The wiring diagram below illustrates a series of typical connections which activate
the load of a Normally Open output when it closes to GND ( ).

External
power supply
13.8V

SmartLiving
1050 control
panel

Generic load
12V Generic
device

Attachment boards 3-10

AUXREL32 3-10-1
The AUXREL32 power distribution board (accessory item) can be used with
SmartLiving 1050L and 10100L models. It provides two relays and allows the
system to take full advantage of the current supplied by the control-panel power-
supply. It comprises 3 pairs of terminals protected by resettable fuses (GND/
AUX1 – GND/AUX2 – GND/AUX3), each able to provide 12V@1A.
Each relay, has a voltage-free contact identified by terminals C1-NO1-NC1 and
C2-NO2-NC2. The relays are activated by the control panel outputs OC1 and
OC2.
Table 22: AUXREL32 - Description of parts D E
A Terminal board F
G G
B 12V connector
C OC1/OC2 connector B
D Relay LED 1 C
A A
E Relay LED 2
F 12V present LED
G Screw locations
G
H OC1/OC2 connection wire
I 12V power wire

30 Installation
Installation and Programming Manual

The activation of each relay is signaled by the on-board LED ([D] for relay 1 and
[E] for relay 2).
If you intend installing this board, work carefully through the following steps.
1. Disconnect all sources of power to the control panel (Mains 230V a.c and H
battery power). I
2. Insert the plastic supports into their respective locations (Table 4: Control
panels - description of parts, Z) on the back of the metal enclosure.
3. Position the board holes [G] on the supports and push the board towards
the back of the enclosure until it locks into position.
4. Insert the cable [H] into the connector [C].
5. Connect the two free wires of the cable [H] to terminals 14 (OC1) and 15
(OC2) on the control panel motherboard. Ensure that OC1 and OC2 on the
control panel are appropriately connected to the connector [C].
6. Connect the cable [I] to the connector [B] and to the 2 free pins [J] of the
connector on the switching power-supply, as shown in the figure.

B I

SmartLink/GWB 3-10-2
The metal enclosures of SmartLiving 1050L and 10100L control panels provide
housing for SmartLink/GWB accessory boards and the respective 12V@1.2Ah
backup batteries.
For the technical features and functions provided by these boards, refer to
paragraph 3-1-6 Land-line connection (PSTN).
The SmartLink/GWB kit includes: A

• SmartLink/G board A
• GSM antenna with 3 meter cable
• Screws and star washers
• Plastic supports for box mounting
• 10 resistors @ 15KW 1/4W
A
The picture opposite shows the SmartLink mounted inside its enclosure. If you
intend installing this board, work carefully through the following steps.
1. Disconnect all sources of power to the control panel (Mains 230V a.c and
C
battery power).
2. Insert the plastic supports into their respective locations (Table 4: Control B
panels - description of parts, C1) on the back of the metal enclosure. D
3. Position the board holes [A] on the supports and push the board towards
the back of the enclosure until it locks into position.
4. Secure the screw and star washer in place [B].
5. Connect terminal “1” ([C] “PWR+”) to a “+AUX” terminal on the control
panel motherboard, and terminal “2” ([C] “PWR-”) to a “ ” terminal on
the control panel motherboard.
6. Power up the control panel (reconnect Mains 230V a.c and battery power).

Installation 31
 Installation and Programming Manual

7. Locate the battery properly into its housing (Table 4: Control panels -
description of parts, E1) and connect the wires [D] (red-positive, black-
negative).

Flex5/U 3-10-3
The metal enclosures of SmartLiving 1050L and 10100L control panels provide
housing for two Flex5/U expansion boards (accessory items).
If you intend installing this type of board, work carefully through the following steps.
1. Disconnect all sources of power to the control panel (Mains 230V a.c and
battery power).
2. Secure the plastic enclosure of the Flex5/U to the backplate of the control
panel (Table 4: Control panels - description of parts, B1).
3. Connect it to BUS line as described in paragraph 3-2-1 The I-BUS line wir-
ing.
4. Address it as described in paragraph 3-3-2 Addressing FLEX5 expansions
and the Air2-BS100 transceiver.
5. Power up the control panel (reconnect Mains 230V a.c and battery power).

SmartLAN 3-10-4
The SmartLAN board, available with SmartLAN/G and SmartLAN/SI versions,
allows SmartLiving control panels to extend their connectivity to ethernet and
internet networks.
The operating capacity of the SmartLAN board depends on the proper
configuration of the networks it is connected to. Therefore, if you are installing a
SmartLAN board, it is necessary to contact the network administrator in order to
configure it correctly.
For a full description of the features and method of configuration of the SmartLAN B
board (IP address, gateway, e-mail, etc.), read carefully through the respective Guide.
The figure opposite shows the SmartLAN/SI board mounted inside the box. If you
intend installing this board, work carefully through the following steps.
A
1. Disconnect all sources of power to the control panel (Mains 230V a.c and C
battery power).
2. Remove the earth connection screw [A] (Table 4: Control panels - descrip-
tion of parts, A1) from its location and replace it with the metal support
(included).
3. Align the screw location on the board with the support and serial connector
on the backplate [B], with the connector on the SmartLiving board (Table
4: Control panels - description of parts, S).
D E
4. Fasten the screw [A] on the support.
5. Insert the board power jumper between pins 1 and 2 of the connector
(Table 4: Control panels - description of parts, O).For SmartLiving 515
model without this connector, use the cable jack and connect it to the con- 3
nector [C], then connect the free red [D] and black [E] wires respectively
to terminals “+” and “-” of the control panel BUS. 2
6. Power up the control panel (reconnect Mains 230V a.c and battery power). 1
It is important to note that the e-mail service does not guarantee delivery time of e-mails Note
and their attachments nor even their final delivery.

32 Installation
Installation and Programming Manual

Chapter 4

FIRST POWER UP

On first power up, the control panel initializes the parameters at default (factory
settings).
The control panel also enrolls all the peripherals it finds on the I-BUS
automatically (automatic addressing phase). The default address of all
expansions, keypads and readers is address 1, therefore, if the system is
equipped with more than one of each type of device, the automatic enrolling
operation will be erroneous. In order to allow the system to perform an accurate
auto-enrolling operation on "First power-up", work carefully through the following
steps.

The default address of all peripherals (keypads, readers and expansions) is set at Note
address 1.

When wiring the system, be careful not to allow any form of power (mains 230V ATTENTION!
or battery) to reach the control panel or its peripherals.

1. Attach the control panel to the wall.

2. Complete the wiring of the peripherals to the BUS.
3. Connect the BUS wires to the control panel.
4. Complete the wiring and balancing of the system detectors.
5. Connect the detectors to the terminals.
6. Connect the outputs to the control panel and peripheral terminals.
7. Connect the control panel to the telephone line.
8. Connect the SmartLogos30M board to the appropriate connector on the
control panel motherboard.
9. Insert the Service jumper in the “SERV” position.
10. Connect the primary power source (230V a.c.).
11. Connect the backup battery. The first line of the display of each keypad in
the system will show the 'Maintenance' message and the keypad address
at default. On first power up (first startup), all the keypads will show "K01"
(refer to paragraph 3-1-9 Maintenance status).

If several keypads are connected to the I-BUS, their displays may be blank. If this occurs, Note
disregard this aspect and go directly to the next step.

12. Address the peripherals (refer to paragraph 3-3 Addressing the peripher-
als). At least one keypad must be assigned to address 1. Using keypad 1,
initialize the addressing phase for nBy/S and nBy/X readers (refer to para-
graph 3-3-3 Addressing nBy readers).
13. If you wish to instruct the system to learn the "balancing values" of all the
zones, initialize the procedure via the installer menu (refer to paragraph 6-
23 Default settings, Learn zone bal.).
14. Remove the jumper from the “SERV” position and place it in the “RUN”
position.
15. If necessary, specify the expansion terminals simulated by the Air2-BS100
transceiver (refer to paragraph 6-5 Terminals) as “Wireless” terminals.
16. If you decide to set up the voice and digital dialer functions and edit the
contact numbers (refer to paragraph 6-8 Telephone).

First power up 33
 Installation and Programming Manual

Chapter 5

INSTALLATION PROJECT VIA

SMARTLEAGUE SOFTWARE

The especially designed SmartLiving system can be programmed from a keypad

or via PC. All programming functions can be accessed through the software
application. You will need:
• A computer (to be connected to the control panel)
• The SmartLeague software application

The SmartLeague 5-1

software application
The SmartLeague software application allows the installer to prepare the majority
of the programming parameters without actually being connected to the control
panel.
The connection is required during the upload and download operations. The type
of connections depends on the device used for upload/download operation to and
from the control panel:
• RS232 serial port of the PC
• LAN (combined with the use of a SmartLAN/SI or SmartLAN/G board)
• Modem
The programming parameters of an installation constitute the “solution”. The
solution can be saved to the memory of the SmartLeague software application,
either for future use or as a “model” for other installations.
The homepage of the SmartLeague software A
application, is common to all the programmable
devices and is always active, even during the
programming session (in the form of a
template):
B
Table 23: SmartLeague software E
application - homepage
A The menu bar, application icons and
programming accessories.
B List of recent solutions - which will allow you
create new solutions or open existing solutions
C Documentation installed on the computer.
D Area dedicated to help and service via Internet.
It is possible to consult FAQ page, make
enquiries and suggestions via e-mail.
E Access to the area reserved for registered users C
of the INIM website.
After typing in a Username and Password, you
can access the updated versions of the software
applications, firmware, technical documentation
and service.

34 Installation project via SmartLeague software

Installation and Programming Manual

Using the software application 5-2

Each project, from the most uncomplicated to the most complex of systems, is
represented by a solution, which contains the programming parameters and
installation structure.
A solution is dedicated to a specific type of apparatus and has its own
programming interface. You can work on several solutions simultaneously, even
if the involve different types of apparatus. Each solution has a template, located
next to the “Homepage”, which can be viewed at all times. In this way it is
possible to compare different solutions and even keep two solutions open, one
real and one for test purposes, in order to verify the effects of programming.
When a solution opens, the SmartLeague software application presents the
following interface::

Table 24: SmartLeague software

application - solutions
A The freshly opened template A
remains in the forefront whilst the
other open template and the
Homepage remain in the C D
background.
E
B Installation tree structure.
C Project Template where you can
select the system peripherals
(keypads, readers, expansions,
sounderflashers) and drag and
drop them to the tree structure. B
D Programming template of the
component to be programmed
(selected from the tree structure).
E Keys for data transfer

A solution can be created or changed even without being connected to the

apparatus. For example, you can plan the layout of an installation or set the
options/parameters at your office and download the settings to the system at a
later time.
In this case, you must:
• Enter the Installer PIN - select “SmartLiving System” from the tree menu on
the left and type in the code in the “Parameters settings - Installer code”
section on the right.
• Select the Type of connection - either from the “Settings – Application data”
section, when using the serial port or a LAN connection, or by pressing the
key, when using the SmartModem100.
For the full instructions regarding these connections, refer to the SmartLAN board
or SmartModem100 Installation Manual.

Creating a Project layout 5-3

The Project layout section, in the SmartLeague software application, allows you
to select the number of peripheral devices you wish to install and thus plan and
configure the system.
You can either create a new solution or change an existing one. The existing
solution can be either a project layout created through the SmartLeague
application or a solution imported directly from a real system.
1. If you wish to create a new system, go to the “Recent Solutions” section
and select “New solution”, then select the type of control panel and
firmware version.
If you wish to modify an existing system, go to the “Recent solutions” sec-
tion and select “Open solution”.
or
import the data from a real control panel by clicking on the key, which
will upload the control panel data.
2. Select the type of peripheral you wish to configure from the “Project” tem-
plate, and drag and drop it to the part of the tree menu concerned.
or

Installation project via SmartLeague software 35

 Installation and Programming Manual

Double-click on the peripheral to add it to the configuration.

To remove a component from the structure, select it and press CANC on
the computer keyboard.
3. To download the data to the control panel, click-on the key. Download-
ing will:
• Block all system keypads. PROGRAMMING
• Broadcast the “PROGRAMMING” message to all the keypads. FROM COMPUTER
• Force all the system keypads to standby status.
• Bring the call queue and events log to a temporary standstill, thus there will
be no events saved to the log, no outputs activated and no outgoing calls.
When the download phase terminates, the control panel will restore the
system to normal operations, as described in paragraph 6-2 Programming
from a keypad (Accessing the installer menu).

During uploading and downloading phases, ensure that the control panel partitions are Note
disarmed. This condition is not necessary when you are viewing the events log.

4. The SmartLeague software application also provides a key which will

allow you to create WinMag interface file (contact your dealer for further
details).

36 Installation project via SmartLeague software

Installation and Programming Manual

Chapter 6

OPTIONS AND
PROGRAMMING
METHODS

Introduction 6-1
The options, functions and values of the SmartLiving control panel must be
programmed by qualified persons only. The SmartLiving control panel is
programmed at the factory with almost ready-to-go settings (“default settings”)
which require only minor changes during the system customization phase.
For example, all the zones, keypads and readers are assigned to (belong to)
partition 1, alarm and tamper events related to partition 1 activate the relay
output which is monostable set at 3 minutes (Monostable time = 3 minutes), etc.
The parameters and programming data can be input via keypad or computer
(equipped with the SmartLeague software application) with the following
exceptions.
• From the keypad you cannot program:
•• Timer slot exceptions
•• Input calibration
•• The second partition entry time
•• Sounderflasher tone
•• BUS speed
•• Description of the “Emergency key duos”
•• Parameters relating to the SmartLAN board
• Via the SmartLeague software application you cannot program:
•• DTMF sensibility
•• The second Installer code
•• The Installer code PINs
•• The shortcut descriptions
The following chapter describes the programming flow of the system data as it
appears in the Installer menu on the keypad. The description of both
programming methods (from Keypad; Via PC) are provided.

Programming from a keypad 6-2

(Accessing the installer menu)
If you wish to program the system via the installer menu from a keypad, you
must:
1. Disarm all the control panel partitions.
2. Type-in a valid PIN (installer code) on the keypad then press . The PIN
is “9999” at default.
If you satisfy these conditions, the system will allow access to installer menu.
Once access to the installer menu is achieved, the system will:
• Block all system keypads except the one you are using.
• Broadcast the “PROGRAMMING” message to all the keypads.
• Force all the system keypads to standby status.
• Bring the call queue and events log to a temporary standstill, thus there will
be no events saved to the log, no outputs activated and no outgoing calls.

Options and programming methods 37

 Installation and Programming Manual

To exit the installer menu, press or , and when the system asks: “EXIT?”
Press (OK = YES). EXIT? OK = YES
When you exit the installer menu, the control panel will:
• Apply all the new settings and values.
• Restore the I-BUS and reprogram and make all the peripherals fully
operational.
• Restore the call queue, and events log to normal operations.

18:23 10/02/10
DASIDASI--

Programming via the 6-3

SmartLeague software
Certain parameters (for example, relating to zones and outputs) can be
programmed only after the project layout of the system has been completed
(refer to paragraph 5-3 Creating a Project layout).
1. Go to the “Recent solutions” section and either create a new solution or
open an existing solution, or import the programming data of a real con-
trol panel by clicking on the key to upload the control panel data.
2. Select the device you wish to configure from the tree menu on the left.
3. Program the parameters in the “Parameters settings” template on the
right.
4. To download the data to the control panel, click-on the key.

The limitations described in paragraph 5-3 Creating a Project layout apply during Note
the uploading and downloading phases.

Panel options 6-4

The following options are provided by the control panel.
Table 25: Panel options
Option If enabled If disabled
Dial tone check The control panel will engage the telephone line,
The control panel will engage the telephone line and check for the “dial
wait two seconds then will start dialing (whether
tone”, if present, the control panel will start dialing.
the dial tone is present or not).
Pulse dialling The control panel will dial using touch tone
The control panel will dial using pulse tone.
(DTMF).
DTMF withoutCode Allows access to the User Menu over-the-phone (during voice calls Allows access to the User Menu over-the-phone
from the control panel) in accordance with the access level (enabled during voice calls from the control panel, only
options, etc.) of the last user code who operated on the control panel after entry of a valid user-code PIN by the
(code 30, 50 or 100). recipient.
Line down signal If a “Tel.Line down” event occurs, the control panel will flash the The control panel will detect the “Tel.Line down”
event, but it will not be revealed on the keypad
respective icon on the keypad displays. displays.
Double call The control panel will override the answerphone function.
Call allVoxNums If several event-generated voice calls are
If several event-generated voice calls are waiting in the outgoing Call waiting in the outgoing Call Queue, the control
Queue, the control panel will attempt to send voice calls to all the panel will send voice calls until it receives
numbers. feedback from one successful call, after which it
will clear the call queue.
Call all TLVNums The same as Call all VoxNums, but related to Alarm Receiving
Centres.
RefreshMnstblOut Each event that triggers an already-activated
Each event that triggers an already-activated monostable output will
monostable output will not refresh (take back to
refresh (take back to zero) the programmed Monostable time.
zero) the programmed Monostable time.
Num10 ForTeleserv Telephone number 10 in the phonebook is reserved for Teleservice
(maintenance over-the-phone). If an end-user makes a request for
Teleservice, the control panel will contact the number in position 10.
Telephone number 10 in the phonebook can be
Note dedicated to either voice or Teleservice.
If you wish the control panel to call an installer company number which
uses an INIM modem, you must set “None” in the Telephone Number
Type field.

38 Options and programming methods

Installation and Programming Manual

Table 25: Panel options

Option If enabled If disabled
Install.callback The control panel will enable the Teleservice function if:
• the installer calls the control panel
• the control panel detects the ring, picks up, recognizes the
installer code and hangs up immediately
• the control panel calls the Teleservice number and allows
access to the system
ReaderBuzzer OFF No reader buzzers will emit audible signals during running entry time,
exit time, output time or pre-arm time.
Keypads lockout If a wrong code is typed-in at a keypad more than 5 times in
succession, the keypad will lock for 10 minutes and show the icon:

Note
If you reset the control panel or access programming while the keypad-
lockout time is running, it will refresh to zero and start again.

View open zones The keypad will show the descriptions of any open zones (zones which
are not in standby status) when the partitions disarm. Any
autobypassable open-zones will be shown in white on a black
background.
OpenZonesArmLock The control panel will not arm the partition if it detects any open zones
(zones which are not in standby status).
If there are zones with the “Autobypassable” or “No Unbypassable”
attribute amongst the open-zones (refer to paragraph 6-6 Zones),
they will be shown on the keypad as “Not ready”. If the user goes
ahead with the arming operation, these zones will be bypassed
automatically and the partition will arm.
DTMF sensitivity The sensitivity of incoming DTMF tones is increased.
BypassAlsoTamper If a zone is bypassed (disabled), it will also be unable to generate If a zone is bypassed (disabled), it will be able to
terminal tamper. generate terminal tamper.
BypassVoiceCheck The control panel will not start the voice
The control panel will start the voice message 5 seconds after dialing
message until it recognizes a voice at the other
the respective contact number.
end of the line.
Confirm with * The control panel will consider the voice call successful when the The control panel will consider the voice call
successful as soon as it starts the voice
recipient presses or on the telephone keypad.
message.
NoUserTamp.reset No user will be allowed to delete of the following events:
• terminal tamper
• control panel open-tamper
• control panel dislodgement-tamper
• peripheral tamper
• peripheral loss
• false key
Encrypt data The control panel will encrypt data via LAN (for SmartLAN/SI only).
Instant restoral The restoral of the magnetic reed sensor in Air2-
The restoral of the magnetic reed sensor in Air2-MC100 wireless
MC100 wireless detectors will be signaled with a
detectors will be signaled instantly.
10 second delay (maximum).
Teleserv. hidden If Teleservice is enabled, the symbol will be
The symbol will not be shown on the keypad display.
shown on the keypad display.
LockInstall.Code After hard reset (refer to ), all the control panel
After hard reset (refer to paragraph 6-23 Default settings), all the
parameters including the installer PIN will reset
control panel parameters with the exception of the installer PIN will
to the factory default settings (installer PIN
reset to the factory default settings.
default is 9999).
50131ReaderLedOFF If there are no keys present at the reader, the LEDs of nBy readers will
be Off. If a key is waved across the reader, the status will be indicated
on the LEDs for 30 seconds before switching Off again. The reader LEDs indicate the related status.
During this 30 second phase, the user can hold the key in the vicinity of
the reader and select the desired shortcut indicated by LEDs.
50131StatHidden If partitions are armed, the LEDs will be as follows:
• Red Keypad LED On solid
• Yellow Keypad LED Off
• Green Keypad LED On
• Partition status hidden
• Status icons not present
• Alarm and Tamper memory hidden The keypad will show the real-time status of the
system at all times, regardless of the status of
If partitions are armed, the real-time status of the system will be
its partitions.
hidden from non-authorized users.
If a valid code is entered at a keypad, it will show the real-time status
of the system for 30 seconds.
The keypad will show the real-time status of the system when all the
keypad partitions are disarmed.

Options and programming methods 39

 Installation and Programming Manual

Table 25: Panel options

Option If enabled If disabled
50131IconsHidden If partitions are armed, the status icons will be hidden from non-
authorized users.
The keypad will show the real-time status of the
If a valid code is entered at a keypad, the status of the icons will be
icons at all times, regardless of the status of its
shown for 30 seconds.
partitions.
The keypad will show the real-time status of the icons when all the
keypad partitions are disarmed.
50131AlarDelayed If an instant-zone alarm occurs on a partition while entry time is
running, the associated actions (calls, output activation, save to log,
etc.) will not be generated until 30 seconds after the expiry of the entry If an instant-zone alarm occurs on a partition
time. while entry time is running, the associated
actions (calls, output activation, save to log,
If the partition (or partitions) are disarmed during this period, the etc.) will be activated instantly.
associated actions will not be generated, however, the keypads will
indicate the violation of the instant zone.
50131WarnLedMem If the control panel detects a fault, the yellow LED on the keypads will
go On and will remain On even after the fault clears. If the control panel detects a fault, the yellow
LED on the keypads will go On and will go Off
To switch the yellow LED Off, clear all activating causes and reset the automatically when the fault clears.
partition.
DayLightSav.time The control panel clock will go back automatically one hour at 03:00
last Sunday in October, and it will go forwards automatically one hour No automatic clock forward/back operations.
at 02:00 last Sunday in March.
NoStringsSiaProt The descriptive strings will be sent in SIA
The descriptive strings will not be sent in SIA reporting format.
reporting format.

Via Keypad PROGRAMMING

Panel options
1. Access the “Programming Panel options” section. Terminals
Type-in Code (Installer PIN) , PROGRAMMING Panel options . Zones

2. Use keys and to select the option you wish to enable/disable.

3. Press to enable the selected option, or to disable it.
4. Press to exit and save the configuration.

Via PC PROGRAMM.OPTIONS
Table 26: Options - via SmartLeague software application Dial tone chec
Option Part of the system Template - section Pulse dialling
Dial tone check Parameters settings - Telephone line
DTMF withoutCo
Pulse dialling parameters
DTMF withoutCode Parameters settings - Telephone dialer
parameters
Line down signal Parameters settings - Telephone line
SmartLiving System - Telephone parameters
Double call Parameters settings - Telephone line
parameters PROGRAMM.OPTIONS
Call allVoxNums Parameters settings - Telephone dialer Dial tone chec
parameters Pulse dialing
Call all TLVNums Parameters settings - Telephone dialer DTMF withoutCo
parameters
RefreshMnstblOut SmartLiving System Parameters settings - Control panel
parameters
Num10 ForTeleserv Parameters settings - Teleservice
SmartLiving System - Telephone
Install.callback parameters
ReaderBuzzer OFF Parameters settings - Reader
Proximity readers parameters
Keypads lockout Parameters settings - Keypad
Keypads
View open zones parameters
OpenZonesArmLock Parameters settings - Control panel
SmartLiving System
BypassAlsoTamper parameters
BypassVoiceCheck Parameters settings - Telephone dialer
SmartLiving System - Telephone
Confirm with * parameters
NoUserTamp.reset Parameters settings - Control panel
SmartLiving System
parameters
Encrypt data Menu bar - Settings - Application
/ settings - Serial ports - SmartLAN/SI

40 Options and programming methods

Installation and Programming Manual

Table 26: Options - via SmartLeague software application

Option Part of the system Template - section
Instant restoral
Parameters settings - Control panel
Teleserv. hidden parameters
LockInstall.Code
50131ReaderLedOFF
50131StatHidden SmartLiving System
50131IconsHidden Parameters settings - 50131
50131AlarDelayed Parameters
50131WarnLedMem
DayLightSav.time
NoStringsSiaProt Parameters settings - Telephone dialer
SmartLiving System - Telephone parameters

Terminals 6-5
This section describes the configuration flexibility of the system terminals. The
profile of each terminal can be configured as follows.
Patent pending
• program the type of terminal:
•• Input (I)
•• Output (O)
•• Two way - supervised output (T)
•• Double Zone (D)
•• Unused (-)
• program the parameters related to the selected configuration PROGRAMMING
Via Keypad Panel options
Terminals
1. Access the “Programming Terminals” section.
Zones
Type-in Code (Installer PIN) , PROGRAMMING Terminals .

The display will show the:

line 1: the number of terminals
line 2: the type of terminals and the selected terminal
line 3: the description of the selected terminal Terminals 12345
line 4: the description of the second zone of the selected terminal if it configured Panel 1-5 IOTD-
as a DOUBLE ZONE.
Panel T01
2. Use and to select the device whose terminals you wish to config-
ure. The terminals are arranged as follows:
• terminals from 1 to 5 on the control panel
• terminals from 6 to 10 on the control panel (SmartLiving 1050 and 10100)
• terminals on expansion boards
• terminals on keypads

3. Use and to scroll across the terminals. The selected terminal will
blink. Configure the terminal by pressing:
• to configure the terminal as an INPUT (“I”)
• to configure the terminal as an OUTPUT (“O”)
• to configure the terminal as a TWO WAY - SUPERVISED OUTPUT (“T”)
• to configure the terminal as a DOUBLE ZONE (“D”)
• to configure the terminal as UNUSED (“-”)
• to enable/disable the terminal as “Wireless”

4. Once you have configured the terminal, press , , , and to

program its type.

If an UNUSED terminal is configured as I, O, T or D and the keypad emits an
error “beep”, it means that you have exceeded the maximum number of
terminals available on the control panel. If you wish to employ the terminal
concerned, you must first configure another terminal as UNUSED.
If you are working on a Flex5 expansion terminal, press key to configure it,
and consequently the entire expansion, as wireless. The “Wireless” string will be

Options and programming methods 41

 Installation and Programming Manual

shown on the bottom line of the display. If you press key again, the
operation will undo.
To configure a terminal as a wireless output, proceed as follows:
To configure a wireless
1. Position the cursor on the terminal concerned.
terminal as an
2. Press to configure the terminal, and consequently the entire expan- “output”, you must
sion, as wireless. first enroll it as an
3. Configure the terminal as an “input” ( ). “input”, and then program it as
an “output”, as described in the
4. Press to access the zone parameters programming section.
instructions (see opposite).
5. Go to the “Wireless” section.
6. Enroll the terminal as “Input 1 C.M.” or “Input 2 C.M.”
7. Press the “ENROLL” button on the Air2-MC100 device.
8. Enable the “Broadcast RF” option as follows:

Type in Code (Installer) , PROGRAMMING Zones , select the zone, Options , BroadcastRF.

The “Broadcast RF” option must be enabled for each terminal of the Air2-MC100 device Note
concerned.
9. Go back to step 1 and configure the terminal as an output ( ).
10. Press to access the output parameters programming section (descrip-
tion, options, etc.).

Press in correspondence with any terminal, provided that it is not an UNUSED

terminal, to access the parameter programming section of the type of terminal
selected, whether it is a zone or an output (refer to paragraph 6-6 Zones or
paragraph 6-7 Outputs).

Via PC
Select “SmartLiving System - Terminals” from the tree menu on the left, then go
to the “Parameters settings” template on the right:
All the terminals will be shown on the respective page. You must configure the
terminal graphically using the mouse, as follows:
1. Point to the terminal you require.
2. Right click on the mouse and select the required type.
3. Double click to set the options for the terminal.
4. Position the mouse on the programming field instead of on the specific ter-
minal to program all the terminals in the same way.
If the terminal is configured as “Zone” (=INPUT) or “Double” (=DOUBLE ZONE),
it will appear in the Zone programming section (paragraph 6-6 Zones). If the
terminal is configured as an “Outputs” (=OUTPUT) or “I/O” (= TWO WAY), it will
appear in the Outputs programming section (refer to paragraph 6-7 Zones).

Zones 6-6
This programming section deals with all the zone parameters.

Via Keypad
1. Access the “Programming Zones” section.

Type-in Code (Installer PIN) , PROGRAMMING Zones .

2. Use keys and to select the zone then press .

Description
This is the editable label which identifies the zone. At default, all the zones
assume the description of the peripheral they refer to, followed by the respective
terminal.
line 1: default description
line 2: current description
line 3: description being edited
line 4: letter/number selection
For example, the default description “Expansion 04 T03 corresponds to the zone
located on terminal T3 of Expansion n. 4. The default descriptions “Panel T05”

42 Options and programming methods

Installation and Programming Manual

and “Panel T05D” correspond to the two zones located on terminal T5 of the
control panel, configured as “Double Zone”.

Partitions
These are the partitions the zone belongs to. A zone configured as “Automation”
cannot be assigned to any partition.
Use and to enable or disable the selected partition.
PROGRAMMING
Type Panel options
Terminals
Use and to select the type of zone, then press . The available Zones
Types are (refer to Appendix A, Technical terminology and Glossary):
• Instant
• Delayed
• Delayed unhidden
• Route
• 24 hour PROGRAMMING
• Automation ZONES
• Armed in Away mode Office
• Disarm Panel T02
• Switch Panel T03
• OnArm/OffDisarm
• Patrol
For “Arm”, “Disarm”, “Switch”, “OnArm/OffDisarm” “Follow” and “Patrol” zones,
refer to Appendix A, Technical terminology and Glossary, Command Zones.
“Delayed” and “Delayed unhidden” zones are delayed during entry and exit
phases, in accordance with the respective “Entry Time” and “Exit Time” settings
Office
(refer to paragraph 6-11 Partitions). A “Delayed unhidden” zone behave as Description
follows: Partitions
•• if violated when the system is disarmed, it will switch Off the blue LED on Type
the keypad
•• if the “View open zones” option is enabled, it will be shown on the keypad
•• it will not generate “Partition not ready” events
•• On arming from a keypad, the zone will appear as a violated zone but,
when the arming operation is confirmed, will behave as a delayed zone and
will not generate an alarm. Panel T01
•• if the “OpenZonesArmLock” option is enabled and the zone is violated, it Office
will appear as a violated zone but, when the arming operation is confirmed, Board room
will behave as a delayed zone and will not generate an alarm. m n oMNO6
•• if the “OpenZonesArmLock” option is enabled, the zone is violated and
instant arming is required, the zone will appear as a violated zone and
when the partition arming operation is confirmed, the partitions the zone
belongs to will not be armed.

Options
The available options (refer to Appendix A, Technical terminology and Glossary)
must be enabled/disabled by keys and :
• Interior
• Auto-bypassable
• Unbypassable
• Chime
• Test
• TampReed/FollPir
• Broadcast RF
• Use sensor LED
The last three options apply to “Wireless” zones only, a full description of which
follows.

Options and programming methods 43

 Installation and Programming Manual

Option If enabled If disabled

TampReed/FollPir • Air2-IR100 - in order to increase battery life, the infrared • Air2-IR100 - the PIR detector will be active at all
sensor will deactivate when the partitions it belongs to are times.
disarmed and will only activate when the partitions it
• Air2-MC100 - magnetic-contact tamper will not be
belongs to arm. detected under any circumstances.
Deactivated detectors do not generate alarms. There may be
up to a 3 minute delay between the partition arming
command and when the detector actually arms.
• Air2-MC100 - detects magnetic-contact tamper when both
reeds are in standby status.
Broadcast RF This option must be enabled when the zone and one of the
terminals of the Air2-MC100 device (“T1” or “T2”) is configured The activation/deactivation of the “wireless” output
occurs within 2 minutes of the command from the
as an “output”. Assures the activation/deactivation of the output control panel.
within 2 seconds of the control panel command.
Use sensor LED The red LED of Air2-IR100 and Air2-MC100 devices provides
visual signaling of alarm and device tamper conditions.
Note The red LED of Air2-IR100 and Air2-MC100 will be “Off”
at all times.
This option must be enabled on all the terminals of the Air2-
MC100.

• No Unbypassable. If this option is enabled, the zone will operate as an

“Autobypassable” zone, with the difference that it will be re-arm automatically
(unbypass) when the partition next disarms.
• NoArmIfNotReady. If this option is enabled, the zone, even if it is a 24H,
automation or delayed zone, will not arm when it is not in standby status. This
option, for 24H or automation zones, can be used together with the control
panel option “NoArmOpenZones”, for management of the “antimask” function
of detectors which have this feature.
• Delay time 2. If this option is enabled, delayed zones will activate the second
partition entry time. If this option is not enabled, delayed zones will activate
the first partition entry time.
• Last exit zone. If this option is enabled, and the zone passes from standby
status to alarm status while the partition exit time is running, the exit time will
be forced to 15 seconds. If the zone passes from alarm status to standby
status, the exit time will be forced to 5 seconds.
• UnbypassOnDisarm. If this option is enabled, a zone which has been
bypassed by a user, will be automatically unbypassed when the partition next
rearms.

Wireless

Please note that this section will be operative only when the zone you are working on is Note
configured as a wireless zone (refer to paragraph 6-5 Terminals).

This section allows you to carry out all the operations relating to the
programming of Air2 wireless series devices. The wireless-device programming
Wireless
section is arranged as follows. Enroll detector
• Enroll sensor - allows you to enroll a wireless detector which has not yet
been enrolled on the terminal concerned.

Press to initialize the enrollment process. Select the type of detector you wish
to enroll:
•• PIR sensor - allows you to enroll an Air2-IR100 detector
•• Magnetic contact - allows you to enroll Air2-MC100 magnetic reed contact
•• Terminal T1 M.C. - allows you to enroll the “T1” terminal of an Air2- Enroll detector
MC100
PIR detector
•• Terminal T2 M.C. - allows you to enroll the “T2” terminal of an Air2-
MC100
Magnetic Contact
Terminal T1 MC
After selecting the desired type, press . The first line of the keypad will show
the “Programming” string.
To enroll the wireless device, press and release its on-board “ENROLL” button. As
soon as the enrolling process is complete, the keypad will emit an audible signal
(beep) to confirm the operation, and will show (in accordance with the type of
device) the following:
• Delete sensor - allows you to delete (unenroll) an enrolled wireless detector
Programming
from the terminal concerned.
• PIR sensor - allows you to change the parameters of an already enrolled
Air2-IR100 detector. Press to program the detector sensitivity and enter a
value of between 1 (low sensitivity) and 4 (high sensitivity).

44 Options and programming methods

Installation and Programming Manual

1. Use keys and to select the field you wish to change, then use the
number keys ( , etc.) to edit the number. Sensibility
or 00_ Units
Use and to increase or decrease the number.
(Min. 001
(Max. 004
2. Press to confirm and exit.
• Magnetic contact - allows you to change the parameters of an already
enrolled Air2-MC100 magnetic contact. Press , to access the following
options:
•• LongSide contact - detection using the long side of the magnetic contact.
•• ShortSideContact - detection using the short side of the magnetic contact.
•• Both contacts - detection using both sides of the magnetic contact.
If you select the “Both contacts” option, standby status will be detected when
either (or both) of the 2 reeds close. If you select either “LongSide contact” or
“ShortSideContact”, standby status will be detected when the selected reed
closes and the other opens. If both reeds close, the system will generate a
terminal-tamper event. In fact, the most common method of jamming this type
of device is to hold a magnet in the vicinity of the magnetic contact, should this
ever occur, both reed relays will close to trigger a tamper event.
• Terminal T1 M.C. and Terminal T2 M.C. - to change the parameters of
terminal “T1” of an enrolled Air2-MC100. If you press at this point, the
keypad will step back to the Zones menu and you can set up the parameters
of the terminal: Balancing, Rollerblind, Times, etc.
Terminals “T1” and/or “T2” of the Air2-MC100 device can be set up in the same
way as wired terminals, with the exception that wireless terminals cannot be
configured as “double zones”.
Balancing
Balancing can be (refer to Appendix A, Technical terminology and Glossary and
paragraph 3-5 Wiring and balancing alarm detectors):
• Norm. open (NO)
• Norm.closed (NC)
• Single balancing
• Double balancing
• Double Zone (without EOL)
• Double Zone EOL (with EOL)
Alarm cycles
This programmable parameter accepts values between 1 and 15. If you set the
value at 15, the zone will operate as a “repetitive zone” (refer to Appendix A,
Technical terminology and Glossary, Alarm cycles).
Detector type
It is possible to program a zone as:
• Generic zone
• Rollerblind
• Shock
The following Table shows the terminals which accept Generic, Rollerblind and
Shock zones, and the respective zone-parameter fields for each type.
Generic zone Rollerblind Shock
Control panel
any T1, T2 T1, T2
terminals
Expansion
any T1, T2, T3 or T4 T1, T2, T3 or T4
terminals
Keypad
any any any
terminals
Extra Al. pulse Duration Shock sensit.
Rollerblind time
Parameters Multipulse time Shock time
Rollerbl. pulses
Alarm pulses Shock pulses
Al. pulse Duration (generic zone)
This is the length of time (after detection of alarm conditions) the zone allows
before generating an alarm. Expressed in multiples of 15 milliseconds or minutes
(see “info” box).
Multipulse time (generic zone)
This parameter applies only when the “Alarm pulse num." parameter is more
than 1.

Options and programming methods 45

 Installation and Programming Manual

This is the window during which a number of alarm pulses must be detected
(each lasting as long as the programmed “Al.pulse Duration”). The number of
alarm pulses must equal or exceed the value programmed for “Alarm pulses”,
before the system generates an alarm. This window can be expressed in seconds
or minutes (see Note).
Alarm pulse num. (generic zone)
This is the number of pulses (each lasting as long as the programmed “Al.pulse
Duration”) necessary to generate a zone alarm event. If this value is more than
1, you must also program the “Multipulse time” parameter.
Rollerblind time (rollerblind zone)
This parameter applies only when the value of the “Rollerbl. pulses” (see below)
is more than 1.
This is the time window during which the system must detect a number of pulses If this value is
equal to or higher than the value programmed for “Rollerblind pulses” before expressed in minutes,
generating a zone alarm. This window can be expressed in seconds or minutes there is an error margin
(see Note). of 1 minute (for
example, if you set 5 minutes,
Rollerbl. pulses (rollerblind zone) the period can vary between 4
This is the number of pulses necessary to generate a zone-alarm event. If this and 5 minutes).
value is more than 1, you must also program the “Rollerblind time”.
Shock sensib. (shock zone)
This is an empirical parameter which regulates the sensitivity of the sensor.
Increasing this value decreases detection sensitivity.
Shock time (shock zone)
This parameter applies only when the “Shock pulses” value is more than 1.
This is the window during which a number of pulses must be detected the number
of alarm pulses must equal or exceed the value programmed for “Shock pulses”,
before the system generates an alarm. This window can be expressed in seconds
or minutes (see Note).
Shock pulses (shock zone)
This is the number of pulses necessary to generate a zone-alarm event.
If this value is more than 1, you must also program the “Shock Time” parameter.
If this value is 0, the zone alarm is generated by the "Shock sensib." parameter.

All the above-mentioned values can be programmed as follows:

1. Use and to select whether to indicate the time in multiples of 15
milliseconds, seconds or minutes (see “info” box).

2. Use keys and to select the field you wish to change, then use the
number keys ( , etc.) to edit the number.
or
Use and to increase or decrease the number.
3. Press to confirm and exit.

Via PC
Programming zones via the SmartLeague application is accomplished by the
selection and programming of the terminal configured as zone, described in
paragraph 6-5 Terminals.

46 Options and programming methods

Installation and Programming Manual

Outputs 6-7
This programming section deals with all the output parameters.
SmartLiving control panels provide 3 outputs:
• Relay Output
• O.C. Output 1
• O.C. Output 2

Via Keypad
1. Access the “Outputs” section.

Type-in Code (Installer PIN) , PROGRAMMING Outputs .

2. Use and to select the output then press .

PROGRAMMING
Terminals
Description Zones
This is the editable output label (device description). At default all the outputs, Outputs
except for the 3 outputs on the control panel motherboard, assume the
description of the peripheral they refer to followed by the respective terminal.
Follow the instructions in paragraph 6-6 Zones - Descriptions.
Output options
Use and to enable or disable the selected option.
Outputs
• Norm. closed: this will be the output status during standby.
RELAY 001
• Monostable
OUTPUT 001
• Buzzer (beeper): generates a 1Khz signal when the output activates - can
be used to drive a buzzer. OUTPUT 002
• Blinker: generates an intermittent signal (0.5 sec ON and 0.5 sec OFF) when
the output activates - can be employed in direct control of a visual signaling
device (e.g. flasher).
• ON afterRestoral: the output does not restore-to-standby (reset) when the
trigger-event clears. This option is useful in situations that require a trigger
event for output activation and a reset event for its deactivation.
This option applies to “Bistable” outputs only. If it is enabled for a bistable RELAY 001
output with reset-event configuration, it will deactivate the output instead of Description
activating it (refer to paragraph 6-9 Events). Output options
This option is useful in situations that require the output to reveal event Monostable time
“memory” (event signaling which continues even after the event clears). In
this case, the output is deactivated by a different event which restores it
directly to standby (resets the output).
For example:
•• O.C. Output 1 is configured as "ON afterRestoral"
•• the activation of “Mains failure” event is programmed to trigger O.C. Output 1
•• the restoral (reset) of "Valid code"event is programmed to trigger O.C. Output.
1
In the event of Mains failure, O.C. Output 1 will activate but will not restore to
standby (reset) when the Mains failure condition clears. It will restore to
standby (reset) only when “CODE 1” is entered a keypad and generates a
“Valid code” for the “CODE 1” event. If this value is
Monostable time expressed in minutes,
there is an error
This parameter applies to “Monostable” outputs only. This interval can be
expressed in seconds or minutes (see “info” box). margin of 1 minute (for
example, if you set 5 minutes,
When a “Monostable” output receives an activation signal, it will remain active the period can vary between 4
(On) for the programmed time, regardless of the status of the trigger-event. In
and 5 minutes).
some cases, “Monostable” outputs can be forced to standby before the
programmed monostable time runs out.

Use keys and and the number keys to set the times.

Via PC
Programming zones via the SmartLeague application is accomplished by the
selection and programming of the terminal configured as output, described in
paragraph 6-5 Terminals.

Options and programming methods 47

 Installation and Programming Manual

Telephone 6-8
This programming section deals with all the telephone parameters.

Via Keypad
Type-in Code (Installer PIN) , PROGRAMMING Telephone .

Select number
Use keys and to access the Phonebook which provides 10 number PROGRAMMING
positions with the following programming fields. Zones
• Number: edit field for the contact number (maximum 20 digits). Accepts also Outputs
“,” (= 2 second pause), “*” and “#”. Telephone
• Description: edit field for the name of the contact person. Follow the
instructions in paragraph 6-6 Zones.
• Type: programming field for the telephone typology.
•• None: for unused telephone number
•• Voice call: assigns the contact number to the voice dialer
If the number refers to the Alarm Receiving Centre, assigns the ARC protocol Telephone
(reporting format): Select number
•• Ademco 10bps Number of rings
•• Ademco 14bps Max.num.attempts
•• Franklin 20bps
•• Radionics 40bps
•• Scantronic 10bps
•• CONTACT-ID
•• SIA - Level 1 SIA is applied This reporting format (protocol) is capable of
sending descriptions of the objects in ASCII characters. if you do not wish Select number
to send the descriptions in ASCII characters, select “No SIA strings” (refer NUMBER 001
to paragraph 6-4 Panel options). You can set a 4, 5 or 6 digit customer NUMBER 002
code for this protocol.
NUMBER 003
Use and to select the Type of number, then press .
• Account code: a 4-character alphanumeric code which identifies the caller in
reports to the Alarm Receiving Centre. Some protocols (reporting formats)
accept digits only, whilst others accept also “A”, “B”, “C”, “D”, “E” and “F”,
available using keys .
• Partitions: you can associate each telephone number with specific partitions.
By selecting the partitions, using Keys and , you enable/disable the NUMBER 001
users (who have at least one of these partitions in common with the telephone Number
number) to modify the number concerned. Description
Number of rings Type
This value determines the number of rings the system allows before picking up an
incoming call.
Max.num.attempts
This value determines the number of calls attempts the system will make before
deleting the contact number from the call queue.
Message repeats
This value determines the number of times the voice message will be played
during the call.
All the above-mentioned values can be programmed as follows:

1. Use keys and to select the field you wish to change, then use the
number keys ( , etc.) to edit the number.
or
Use and to increase or decrease the number.
2. Press to confirm and exit.

48 Options and programming methods

Installation and Programming Manual

Via PC
Table 27: Telephone - via SmartLeague software application
Option Part of the system Template/section
Select number Programming
Number of rings Parameters settings - Telephone
SmartLiving System - Telephone line parameters
Max.num.attempts Parameters settings - Telephone
Message repeats dialer parameters

Events 6-9
This programming section deals with all the event-generated output-actions
(activations/deactivation) and voice/digital calls.
Event notification via e-mail requires the use of a SmartLAN/G board (refer to
paragraph 3-10-4 SmartLAN).
The following table shows the events the control panel recognizes, the number of
events for each type, the trigger and restoral method of each event and the event
category (Pulse).
Table 28: Event type
Occurs when... Restores when ... Number of events Pulse events
(Spot Events)
Zone alarm A zone generates an alarm A zone restores One event for each zone no
Terminal tamper A terminal detects tamper (short-
circuit or wire cutting) A terminal restores One event for each terminal no
Partition alarm A 24h zone which belongs to the
partition generates an alarm, or a All the zones belonging to the
zone which belongs to the partition One event for each partition no
generates an alarm during Away partition restore (reset).
mode.
StayPartit.alarm A zone which belongs to a partition All the zones belonging to the
armed in Stay or Instant mode, One event for each partition no
generates an alarm. partition restore (reset).

Partition tamper A zone which belongs to the partition

All the zones belonging to the
detects tamper (short-circuit or wire partition restore (reset). One event for each partition no
cutting).
Zone bypass A zone is disabled (switched Off) A zone is enabled (switched On) One event for each zone no
Real-time zone The electrical status of a zone The electrical status of a zone
switches from standby to alarm switches from alarm to standby
One event for each zone no
The event is independent of the zone type and the armed/disarmed status
of the partitions.
Partit.not ready A zone which belongs to the partition All the zones belonging to the One event for each partition no
is not in standby status. partition are in standby status.
Away arm request A request is made to arm the interior A request is made to disarm the
and perimeter zones of the partition partition One event for each partition Yes
Overtime request A request is made to arm the partition
A request is made to disarm the
in Stay mode (perimeter zones only) partition One event for each partition Yes
or in Instant mode
Partit.AwayArmed The partition interior and perimeter The partition has been disarmed
zones have been armed effectively effectively One event for each partition no
Partit.StayArmed The partition has been armed The partition has been disarmed
effectively in Stay or Instant mode effectively One event for each partition no
armed
Partition reset A request is made to reset the
partition One event for each partition Yes

Exit time The partition exit time is running The partition exit time expires One event for each partition no
Entry time The partition entry time is running The partition entry time expires One event for each partition no
Pre-arm time The partition Pre-arm time is running The partition Pre-arm time expires One event for each partition no
Overtime request A request for overtime relating to the One event for each partition Yes
partition is made
Chime A chime zone belonging to the
partition is violated One event for each partition Yes
Forced arming At the time of an arming command,
relating to one or more partitions,
there are open zones on the partition/
partitions involved, or there are other One event for each partition Yes
conditions present which lower system
security, nonetheless, the user arms
the system.
Valid code A user-code PIN entered at a keypad
One event for each code Yes
is recognized as valid
Valid key A key used at a reader is recognized One event for each key Yes
as valid on the reader

Options and programming methods 49

 Installation and Programming Manual

Table 28: Event type

Pulse events
Occurs when... Restores when ... Number of events (Spot Events)
Valid Code AtKeyp. A user-code PIN entered at a keypad
One event for each keypad Yes
is recognized as valid on the keypad
ValidKeyAtReader A key used at a reader is recognized
as valid on the reader One event for each reader Yes
Partition code A user-code PIN entered at a keypad
One event for each partition Yes
is recognized as valid on the partition
Partition key A key used at a reader is recognized One event for each partition Yes
as valid on the partition
Failed call One event for each contact
A call is not answered telephone number Yes

Timer activated The timer is enabled (On) The timer is disabled (Off) One event for each timer no
Thermostat ON The activation conditions set for the The deactivation conditions set for
One event for each keypad no
keypad thermostat occur. the keypad thermostat occur.
ScenarioActivated The status of all the partitions The status of all least one of the
corresponds exactly to the pre-set partitions does not correspond to One event for each scenario no
scenario. the pre-set scenario.
Emergency key One of the emergency-key duos is One event for each
Yes
pressed emergency-key duo
Panel opened The control-panel enclosure cover is The control-panel enclosure cover 1 no
opened is replaced
Dislodged panel 1 no
Zone fuse fault The zone protection fuse on the
control panel is not operational The zone protection fuse on the 1 no
control panel restores
(blown)
IBUS fuse fault The I-BUS protection fuse is not The I-BUS protection fuse restores 1 no
operational (blown)
Low battery The backup battery is low The backup battery is charged 1 no
Mains failure The primary 230V a.c. power source is The primary 230V a.c. power
absent (blackout) source restores 1 no
Expansion tamper An expansion board signals tamper Tamper conditions clear on all the
1 no
conditions system expansion boards
Keypad tamper A keypad signals tamper conditions Tamper conditions clear on all the 1 no
system keypads
Reader tamper Tamper conditions clear on all the
A reader signals tamper conditions system readers 1 no

Siren tamper A sounder/flasher connected to the All the sounderflashers connected

1 no
BUS signals tamper to the BUS reset
Expansion loss An expansion board fails to The I-BUS restores
communication with all the system 1 no
communicate with the I-BUS expansion boards
Keypad loss A keypad fails to communicate with The BUS restores communication
1 no
the I-BUS with all the system keypads
Reader loss A reader fails to communicate with the The I-BUS restores
communications with all the 1 no
I-BUS system readers
Sounderflasher loss A sounderflasher fails to communicate The BUS restores communication
1 no
with the BUS with all the sounderflashers
Jamming Wireless interference detected Wireless interference cleared 1 no
Low battery WLS The battery of a least one wireless All the wireless detectors are 1 no
detector is running low running on low batteries
WLS zone loss Loss of at least one wireless detector
has been signaled (supervisory time- All the wireless detector are 1 no
present
out)
Installer code An Installer PIN entered at a keypad is 1 Yes
recognized as valid
Invalid code An invalid code is entered at a keypad 1 Yes
False key An invalid key is used at a reader 1 Yes
Tel. line down The land line is not working The land line restores 1 no
Periodic event The Periodic Event occurs 1 Yes
Hard reset The control panel re-initializes. The
system clock may be wrong or not 1 Yes
working properly.
Call queue full There are no more slots left in the
outgoing call queue 1 Yes
Successful call The call is answered 1 Yes
Programming Access to system programming is
End of system programming 1 no
authorized
Ongoing call A call is sent A call ends 1 no
Output fault An output fails to switch status as 1 Yes
commanded

50 Options and programming methods

Installation and Programming Manual

Each event can be associated with 3 voice messages, selected from the message
list (refer to Appendix D, Voice messages). PROGRAMMING
• Message type Outputs
• Message A Telephone
• Message B Events
This feature allows you to create messages which will be played during event-
related voice calls to contact numbers, both at the start and end of the event.
The choice of messages and the number of times they are played depends on the
“AutomaticDialer” settings.
Events
Via Keypad Zone alarm
1. Accessing the “Events” section Terminal tamper
Type-in Code (Installer PIN) , PROGRAMMING Events . Partition alarm

2. Use keys and to select the event type (if you are dealing with a group
of events, repeat the operation) then press .
3. Select:
• Activation - to program the actions to be carried out when the event occurs.
• Restoral - to program the actions to be carried out when the event ends. Zone alarm
Panel T01
Panel T02
4. Successively, the parameters to program are: Panel T03
TelephoneNumbers
Program the call recipient numbers
Message type
Message A
Events
Message B Activation
Select the number of the message (see Table 29: Event-related messages and Restoral
Appendix D, Voice messages):

1. Use keys and to select the field you wish to change, then use the
number keys ( , etc.) to edit the number.
or
Use keys and to increase or decrease the number.
Events
2. Press to confirm and exit. TelephoneNumbers
The following table shows the voice-message sequence in accordance with the Message type
previously mentioned parameters and options. Message A
Table 29: Event-related messages
“Automatic dialer” “Automatic dialer”
enabled disabled
Message type Plays the message relating to the event
type (e.g. “zone alarm”, “Mains failure”) You can select any message from 1 to 219
This message should not be changed. Events
Message A Blank message, editable Message A
Message B Contains event details, for events which are not distinctive Message B
(e.g. the “zone alarm” event provides information regarding the zone concerned). Options
Event 1. Message type + 260 1. Message type
Activation 2. Message A 2. Message B
Sequence 3. Message B 3. “Location” (message n.100)
4. “Location” (message n.100)
Sequence in the 1. “Restored” (message 1. Message A
event of n.97) 2. Message B Options
Restoral 2. Message type 3. “Location” (message n.100) Event OFF to l
3. Message A
4. Message B
Event OFF to l
5. “Location” (message n.100) StartPeriodicE

If an event is associated with the “Automatic dialer”, the “Type Message” option refers to Note
messages 261 to 312, that is to say, the messages containing the event descriptions
(event types).

Options and programming methods 51

 Installation and Programming Manual

Options
To be activated by keys and :
Option If enabled If disabled
Event ON to log When the event occurs, it will be saved to the events log. When the event occurs, it will not be saved to the events
log.
Event OFF to log When the event clears, it will not be saved to the events
When the event clears, it will be saved to the events log. log.
StartPeriodicEv. When the event occurs, the system will generate the
Periodic event.
Silent event If the event occurs, the system will generate silent calls If the event occurs, the system will generate calls which
which will not be signaled on the keypads. will be signaled on the keypads.
Clear call queue When the event occurs, the system will cancel the
outgoing call queue.
Send address In the case of voice calls, the system will include the In the case of voice calls, the system will not include the
address of the location alarm (refer to the Table 29: address of the location alarm (refer to the Table 29:
Event-related messages) Event-related messages)
Local Message ON When the event occurs, the system will play the event-
related voice message on keypad speaker n. 1
Local MessageOFF When the event occurs, the system will not play the
event-related voice message on keypad speaker n. 1
Automatic Dialler Refer to the Table 29: Event-related messages
Priority Calls associated with this type of event have priority over
all other calls. Therefore, if a priority event occurs, any
ongoing calls will be interrupted and the priority-event
call will be sent immediately.
Class code
This is the CONTACT-ID reporting format Class-Code which corresponds to the
event.
Event code
This is the 2-character alphanumeric code, which corresponds to the event sent
the alarm receiving centre (ARC). For zone and terminal events (alarm, tamper,
bypass), the “CCC” field of the CONTACT-ID protocol counts the number of hard
terminals in accordance with the Hard terminals table (refer to Appendix E, Screw
Terminals).
Outputs
When programming the Event-Activation section, program the main output which will
be activated when the event occurs. When programming the Event-Restoral section,
program the main output which will be activated when the event ends.
Select the output from the list (which includes the Relay outputs, OC1, OC2 and the
terminals configured as outputs and also the sounderflashers) and press .

If the output has the “ON afterRestoral” option enabled (refer to paragraph 6-7 Outputs) Note
and it is programmed on event restoral, the output will deactivate when the event occurs.

Other outputs
This section allows activation of added outputs (as well as the output
programmed in the “Outputs” parameter) when the event occurs or restores.
These added outputs can be selected by means of keys and from a
programmable list in the “Added Outputs” section.
OtherOutputsProg
This section allows the creation of the list of outputs (16 for “Activation” or 8 for
“Restoral” to be programmed in the “Other outputs” section.

This is the sole list for the entire control panel and is independent of the type of event. Note
Use keys and to select and to confirm.
SirenSound types
This section allows you to select the audible-visual signals emitted by the
sounderflashers, when these are programmed in the “Outputs” and “Other
outputs” section.
Please note that the “Tone Type” is a parameter of the event. Therefore, if
several sounderflashers have been programmed in relation to a specific event,
they will all emit the programmed tone when the event occurs. If a
sounderflasher has been programmed in relation to several events, it will emit
the last tone type setting received in order of time.

Use keys and to select and to confirm.

52 Options and programming methods

Installation and Programming Manual

For further information regarding the “Outputs”, “Other outputs” and “Tone type”
parameters of each event, refer to Appendix F, Combination of outputs triggered
by events.

Via PC
Table 30: Events - via SmartLeague software application
Option Part of the system Template/section
TelephoneNumbers
Message type
Message A
Message B
SmartLiving System - Events - Programming
Options
select the event type
Class code
Event code
Outputs
Other outputs Parameters settings - Other outputs
OtherOutputsProg SmartLiving System - Events Parameters settings - Outputs
Siren sound types SmartLiving System - Events -
select the event type SmartLiving System - Siren pattern

Timer 6-10
PROGRAMMING
This programming section deals with the 10 system Timers.
Telephone
A timer can be associated with a: Events
• Partition - if a partition is associated with a timer which controls automatic- Timers
arming operations (refer to paragraph 5-4 Activations in the User's Manual), it
will arm when the timer switches ON and disarm when the timer switches OFF.
• Code - if a code is associated with a timer, it will be enabled to operate the
system when the timer switches ON, and disabled when the timer switches
OFF.
• Key - if a key is associated with a timer, it will be enabled to operate the Timers
system when the timer switches ON, and disabled when the timer switches TIMER 001
OFF. TIMER 002
In order to associate timers with the partitions, codes and keys, it is necessary to TIMER 003
access the respective control-panel programming section.

The timers must be enabled/disabled by the user (refer to paragraph 5-4 Activations in Note
the User's Manual)).
When you exit the programming session (via keypad, PC or modem) all the timers will be
enabled automatically, therefore, it will be necessary to reset the timers as before.
TIMER 001
Via Keypad Sunday
1. Accessing the “Timers” section: Monday
Type-in Code (Installer PIN) , PROGRAMMING Timers . Tuesday

2. Use keys and to select the Timer then press .

3. Using the same keys, select the day of the week.
4. Select “Activation” and/or “Restoral”.

5. Use keys and to set the time (expressed in hours and minutes) and TIMER 001
and to select the number. Activation
Restoral
6. Press to confirm and exit.

It is also possible to program timer activation or restoral only. Note

If you do not wish to program the timer activation or restoral setting, enter “--:--” in the
field you do not wish to program.

Via PC
Select an item from “SmartLiving System - Timers” from the tree menu on the TIMER 001
left, then go to the “Parameters settings” template on the right:
--:--
The SmartLeague software application allows you to program 15 setting
exceptions for each timer (for holiday periods, etc.).
Each “timer exception” allows you to define different On and Off times for the
selected interval (1 or more days, 1 week, etc.). The pre-set times will be applied

Options and programming methods 53

 Installation and Programming Manual

for the entire interval. The system does not accept intervals which go over the
end of the year. Therefore, it is impossible to program an interval such as 12th
December to 5th January. In such situations, you must program 2 “timer
exceptions”, one from 12th to 31st December and the other from the 1st to 5th
January, both with the same On and Off settings.
The exceptions have priority over the days of the week. For example, If a “timer
exception”, lets say 1st May, falls on a Tuesday the settings programmed for 1st
May will be applied.

The “timer exceptions” cannot be programmed via keypad. Note

Partitions 6-11
This programming section deals with the system Partitions and the respective
options and parameters.
PROGRAMMING
Via Keypad Events
1. Accessing the “Partitions” section: Timers
Partitions
Type-in Code (Installer PIN) , PROGRAMMING Partitions .

2. Use keys and to select the partition then press .

Description
This is the editable partition label (description).
Exit time PROG. PARTITIONS
A period, expressed in minutes or seconds, during which the user must LEAVE the
PARTITION 001
partition after arming the system (see the “info” box). If you set “0” in this field, PARTITION 002
there will be no Exit time (delay), therefore, any delayed zones, which belong to PARTITION 003
the partition, will generate alarms if they are not in standby status when the
system arms.
Entry time
A period (expressed in minutes or seconds) that the system allows the user to
disarm the partition after violation of a delayed zone (for example, after opening
the front door). If the system is not disarmed within the set time it will generate PARTITION 001
an alarm (see “info” box). If you set “0” in this field, there will be no Entry time
(delay), therefore, any delayed zones will generate alarms instantly if they are
Description
violated when the system is armed. Exit time
Tuesday
Pre-arm time
The period (expressed in minutes) before an automatic arming operation (see
“info” box).
Patrol time
An “Inspection” period (expressed in minutes) which allows patrol-key/code
holders (security staff, night watchmen, etc.) to check the premises (see “info” If this value is
box ). expressed in minutes,
All the above-mentioned “times” can be programmed as follows: there is an error
1. Use keys and to choose whether to indicate the time in seconds or margin of 1 minute (for
minutes (see “info” box).. example, if you set 5 minutes,
the period can vary between 4
and 5 minutes).
2. Use keys and to select the field you wish to change, then use the
number keys ( , etc.) to edit the number.
or
Use keys and to increase or decrease the number.
3. Press to confirm and exit.

Timers
Select the timer you wish to associate with the “auto-am” operations.

Ensure that the partition “auto-arm” option is enabled in the respective section: Note
Type in Code (User) , Activations .

Options
• Auto-resetMemory - if enabled by means of the key, each partition
arming operation will reset the partition alarm/tamper memory automatically.

54 Options and programming methods

Installation and Programming Manual

• Auto-arm STAYmode - if enabled by means of the key, the partition

will arm in Stay mode at the pre-set auto-arm time. If disabled by means of
, the partition will arm in Away mode at the pre-set auto-arm time.
• StopTelOn Disarm - if enabled, the call queue will clear when the partition
disarms.

Via PC
Select an item from “SmartLiving System - Partitions” from the tree menu on the
left, then go to the “Parameters settings” template on the right:

User Codes 6-12

This programming section deals with the user code options/parameters. PROGRAMMING
The user code PINs must comprise 4, 5 or 6 digits. The PIN of user code n. 1 is
Timers
“0001” at default. The PINs of the successive user codes are “0002”, “0003”, etc. Partitions
Codes
Via Keypad
1. Accessing the" Codes” section:

Type-in Code (Installer PIN) , PROGRAMMING Codes .

2. Use keys and to select the code then press .

PROGRAMM.CODES
Description CODE 001
This is an editable programming field for the code user's name. CODE 002
Partitions CODE 003
Select the partitions the user code is assigned to. Press , to enable the
partition and to disable it.
Options
Use and to enable/disable the code options.
• Main User - a main user can: CODE 001
•• enable/disable all user codes except other Main User codes Description
•• change its own PIN, and the PINs of all user codes except other Main User Partitions
codes Options
If this option is not enabled the user code will not have “Main User” status.
• Partition filter - if this option is enabled for codes with “Main User” status, (A)
the user will have the authority of a “Main User” only on the partitions it is
assigned to. For example, if a code is configured as “Main User” with Partition
User Code
filter and is assigned to partitions 1, 3, 5 and 7, it will be able to enable/ Manage alarms
disable and change the PINs of all user codes but not Main User codes Arm/Disarm ops.
assigned to these partitions. Voice functions
• Text menu and User menu - the combination of these two options allows
instant access to the respective menus (the menu screens appear instantly on
the keypad display) when the user PIN is typed-in at a keypad and is
pressed. Refer to the following table.
(B)
Case Text menu User menu Description User Code
Accesses the standard user-menu; at this point the
A Disabled Enabled user can scroll the list using and and
select the required option.
Shows the personalized user-icons associated with
B Disabled Disabled function keys , ..., ; at this point the
user can press the required function key and
activate the respective shortcut.
Shows the descriptions of the personalized user-
icons associated with function keys. instead of the
shortcut icons. The user can use and
(C)
C Enabled Disabled
to scroll the list and select the shortcut, which can User Code
be activated by means of the key. Stop alarms
D Enabled Enabled The same as “C” Delete memory
View menu
In all methods of access (A, B and C), the key allows you to access/view the other Note
cases in succession, see figure.

Options and programming methods 55

 Installation and Programming Manual

• AnnounceShortcut - (for JOY/MAX keypad only) if enabled, after PIN entry

followed by , the voice guide will announce the available shortcuts for the
user-code concerned and the respective number keys on the keypad.

Set the “Loc.KpadMess Time” (refer to paragraph 6-25 Other parameters) to allow the Note
system to play the messages associated with all the shortcuts assigned to number keys
, ..., .
• Remote access - if enabled, the code PIN can be used to operate the system
from any remote telephone.
If the code PIN is entered on a remote telephone keypad, only the shortcuts
associated with keys 0 to 9 can be used to:
•• Arm/Disarm
•• Stop alarms
•• Clear call queue
•• Delete memory
•• Activate outputs
•• Deactiv. outputs
•• Listen-in
•• Arming status
Any other type of command will have no effect.
• Patrol - if enabled, the code will be able to disable the system for the pre-set
“Patrol time”.
Func.KeyShortcuts
This section allows you to program up to 12 shortcuts associated with keys ,
..., . After valid PIN entry followed by , the keypad will show the icons
that correspond to shortcut keys , ..., . Press the corresponding key to
activate the respective shortcut.
0/9 Key shortcuts
This section allows you to program up to 10 shortcuts associated with keys ,
..., . After valid PIN entry followed by , the user will be able to activate
specific shortcuts by means of the number keys.

To assign the shortcuts to the function keys, work through the following steps.
1. Use key or to select the key you wish to associate with the shortcut
then press .

2. Press then use key or to select the shortcut you wish to associ-
ate with the key from the “Type” list.
3. Press to confirm and exit.
4. If the shortcut is associated with “Arm/Disarm” operations, the application
will ask you to select a scenario. If the associated shortcut is “Activate out-
puts” or “Deactiv. outputs”, the application will ask you to select an output.
Assigned outputs
This section allows you to enable/disable the outputs the code user can control
manually via the User Menu>Outputs ON/OFF.
1. Use keys and to select the desired output.
2. Use keys and to enable/disable manual control of the output for
the code concerned.
3. Press to confirm and exit.

Timers
This section allows you to assign a timer to the code. The code will be operative
only at the pre-set times.
Enable/disable
This section allows you to enable/disable access to the various sections of the
User Menu.
For further details regarding the User Menu, refer to the “User Menu” section.
The programming steps are identical to those of “Outputs ON/OFF”.

56 Options and programming methods

Installation and Programming Manual

Via PC
Select an item from “SmartLiving System - Users - Codes” from the tree menu on
the left, then go to the “Parameters settings” template on the right.

Installer codes 6-13

This section allows you to program the functions of the 2 installer codes. The user
code PINs must comprise 4, 5 or 6 digits.
PROGRAMMING
Via Keypad Partitions
Type-in a valid code (Installer) , PROGRAMMING Installer code . Codes
Installer Code
ChangeInst.PIN 1
For security reasons, you must change the PIN of the primary installer code
(type-in twice). The PIN is “9999” at default.
ChangeInst.PIN 2
For security reasons, you must change the PIN of the secondary installer code
(type-in twice). The PIN is “9998” at default. INSTALLER CODE
ChangeInst.PIN 1
Inst.code2Access
ChangeInst.PIN 2
Use and to enable/disable the Installer-Menu sections the secondary Inst.code2Access
installer code can access.

In this section, the secondary installer code can access Inst.CodePIN2 section only. Note

Keys 6-14
This section will allow you to program the parameters of the digital keys and
Air2-KF100 wireless keyfobs (for details regarding the wireless keyfobs, refer to
the Air2-BS100 Transceiver Installation guide).
PROGRAMMING
Via Keypad Codes
Type-in Code (Installer PIN) , PROGRAMMING Keys . Installer Code
Keys
Enroll
Each digital key and wireless keyfob must be enrolled separately on the system in
order to allow it to operate. The enrolling procedure is as follows.
1. View the readers in the control panel configuration. Select the reader you
wish to use in order to enroll the key/s, then press . If you select a
reader simulated by the Air2-BS100, a “W” will be shown at the end of the Keys
description. Enroll
Key parameters
2. Select the digital key you wish to enroll and press . If you are using an Delete key
nBy/S or nBy/X reader, all the LEDs will begin to blink to indicate that it is
ready to enroll the key.
3. The keypad will indicate the current description of the digital key con-
cerned.
4. Hold the digital key in the vicinity of the reader and then move it away. For
Air2-KF100 wireless keyfobs, press contemporarily keys 3 and 4.
5. The keypad will emit a beep to confirm that the digital key has been suc- Zone alarm
cessfully enrolled. If you are using an nBy/S or nBy/X reader, the red LED Panel T01
will go On. The digital key description will go to the next key automatically. Panel T02
This method (from step 4.) allows you to enroll as many digital keys as the Panel T03
system requires.
6. Once you have completed the enrolling process, press or .

All the enrolled keys will be enabled to operate the system immediately. Note
Key parameters
This section allows you to program the digital keys. Readers
• Description - editable field for the name of the digital key user. READER 001
• Partitions - the partitions the digital key is assigned to and therefore can READER 002
control. READER 003

Options and programming methods 57

 Installation and Programming Manual

• Options - activated by means of keys and , are:

Option If enabled If disabled
Patrol The digital key will be able to disarm specific
partitions for patrol purposes.
Maintenance The digital key will be able to block alarm/tamper
outputs for the time that it is held in front of a
reader.
Use If a digital key is held in the vicinity of a reader, If a digital key is held in the vicinity of a reader, These options do
keyShortcuts only the reader shortcuts will be indicated and, if
only the digital key shortcuts will be indicated, configured, the first shortcut programmed on the not apply to Air2-
and not the reader shortcuts. KF100 wireless
digital key.
DisarmNotAllo If a digital key is held in the vicinity of a reader If a digital key is held in the vicinity of a reader keyfobs.
wed when partitions are armed, the Disarm option will when partitions are armed, the Disarm option will
be inhibited (all LEDs Off). be allowed (all LEDs Off).

• Timers - this section allows you to associate a timer with the digital key. The
key will be able to operate the system only when the associated timer is “On”.
• Shortcuts - this section allows you to program up to 4 shortcuts (F1, F2, F3,
F4) for each key.
The shortcut associated with the key can be one of the following types:
•• None
•• Arm/disarm
•• Stop alarms
•• Clear Call Queue
•• Delete memory
•• Activate Output
•• Deactiv. outputs
•• Overtime
•• Teleservice req.
•• Voice guide
If a digital key is held in the vicinity of an nBy/S or nBy/X reader, the LEDs will
run through a series of visual signals with the following meanings:
Option: Use keyShortcuts
LED indicator sequence
enabled disabled
shortcut associated with the red LED on the
1 Red LED On Digital key shortcut F1 reader
shortcut associated with the blue LED on the
2 Blue LED On Digital key shortcut F2 reader
shortcut associated with the green LED on
3 Green LED On Digital key shortcut F3 the reader
shortcut associated with the yellow LED on
4 Yellow LED On Digital key shortcut F4 the reader
5 All LEDs On This sequence does not occur Digital key shortcut F1
Option: DisarmNotAllowed
enabled disabled
6 All LEDs Off
No request to arm ALL the partitions Request to arm ALL the partitions common
common to both the key and reader. to both the key and reader.
Delete key
This section allows you to delete enrolled digital keys from the system
configuration. The enrolled digital keys can be found in the list with the
symbol.
1. Use or to select the digital key you wish to delete.
2. Press to delete the selected digital key.
3. Press to confirm and exit.

Enable/disable
This section allows you to enable/disable the digital keys:
1. Use or to select the digital key you wish to enable/disable
2. Use keys or to enable/disable the selected digital key.
3. Press to confirm and exit.

Via PC
Select an item from “SmartLiving System - Users - Digital keys” from the tree
menu on the left, then go to the “Parameters settings” template on the right.

58 Options and programming methods

Installation and Programming Manual

Arming scenarios 6-15

This section allows you to configure up to different 30 arming scenarios.
PROGRAMMING
Via Keypad Installer Code
1. Access “Arming scenarios” section. Keys
Arming Scenarios
Type-in Code (Installer) , PROGRAMMING Arming scenarios .

2. Use keys or to select the scenario then press .

Description
Editable field for the description of the scenario.
Icon Arming Scenarios
This section allows you to select the icon you wish to assign to the scenario,
SCENARIO 001
simply by indicating the icon number (refer to Appendix B, Shortcuts at default): SCENARIO 002
SCENARIO 003
1. Use keys or to scroll across the digits.
2. Use the number keys ( , etc.) to edit the number.
3. Press to confirm and exit.

The “Arm” shortcut associated with function key to will use (reveal)
the icon selected in this section. SCENARIO 001
Partitions
Description
Icon
This section allows you to configure the scenarios of all the partitions managed by Partitions
the various models.

1. Use keys or to select the partition, then press .

2. Use keys or to select the operating mode (Away, Stay, Disarm, etc.).
• None - the current operating mode of the partition will not be changed.
• Away - the partition will arm in Away mode (interior and perimeter).
• Stay - the partition will arm in Stay mode (perimeter only).
• Instant - the partition will arm in Instant mode (perimeter only with zero delay).
• Disarm - the partition will disarm.
Output
Each scenario, when applied, can activate one output (via keypad, at reader,
over-the-phone, etc.). Use or to select the output then press .

It is possible to use a scenario to activate an output. This can be done through the Note
Scenarios section by simply leaving the respective “Partition” programming fields free
(None), thus allowing the association of the Icons with the outputs.

3. Press to confirm and exit.

Via PC
Select an item from “SmartLiving System - Scenarios” from the tree menu on the
left, then go to the “Parameters settings” template on the right.

Shortcuts 6-16
This section allows you to create up to 36 different shortcuts. PROGRAMMING
Keys
Via Keypad Arming Scenarios
1. Accessing the “Shortcuts” section: Shortcuts
Type-in Code (Installer PIN) , PROGRAMMING Shortcuts .

2. Use keys or to select the shortcut then press .

Description
This is the editable label which identifies the shortcut. Shortcuts
Arm/Disarm
Stop alarms
Clear Call Queue
Options and programming methods 59
 Installation and Programming Manual

Icon
This section allows you to select the icon you wish to represent the scenario,
simply by indicating the icon number (refer to Appendix B, Shortcuts at default):

1. Use keys or to scroll across the digits.

2. Use the number keys ( , etc.) to edit the number.
3. Press to confirm and exit.

Via PC
Select an item from “SmartLiving System - Shortcut icons” from the tree menu
on the left, then go to the “Parameters settings” template on the right.

Expansions 6-17
This section allows you to program the digital keys.
PROGRAMMING
Via Keypad Arming Scenarios
Type-in Code (Installer PIN) , PROGRAMMING Expansions . Shortcuts
Expansions
Enable/disable
This section allows you to add/remove expansions from the I-BUS configuration,
by means of keys and .
ChoosePeripheral
This section allows you to edit the description of each expansion board.
Expansions
Via PC Enable/disable
Table 31: Expansions - via SmartLeague software application ChoosePeripheral
Option Part of the system Template/section
Enable/disable / Project
ChoosePeripheral Expansions - select the expansion Programming

Keypads 6-18
This section allows you to program the digital keys.

Via Keypad
Type-in Code (Installer PIN) , PROGRAMMING Keypads .
PROGRAMMING
Shortcuts
Enable/disable Expansions
Keypads
This section allows you to add/remove expansions from the I-BUS configuration,
by means of keys and .
ChoosePeripheral
This section allows you to program the various options of the selected keypad.
• Description - editable field for the name of the digital key user. Keypads
• Partitions - use and to enable/disable the keypad on the system Enable/disable
partitions. ChoosePeripheral
• Options:
•• Temperature off - if this option is enabled, the room temperature will be
flashed in alternation on the display. This option applies to JOY/MAX
keypads only.
•• SilentExitTime - enable/disable the buzzer during partition Exit Time.
•• SilentEntryTime - enable/disable the buzzer during entry partition Entry
time Keypads
•• SignalExitTime - enable/disable the buzzer when terminal T1 on the Enable/disable
keypad is activated as an output. ChoosePeripheral
• Func.KeyShortcuts - shortcuts assigned to keys , ..., . Function
keys F1 to F12 must be selected separately and programmed as follows:
•• Type - this is the shortcut action which can be selected from those
available (refer to Appendix B, Shortcuts at default). It is necessary to
program an extra parameter for some shortcuts:

60 Options and programming methods

Installation and Programming Manual

- “Arm/disarm”, this parameter refers to one of the 30 scenarios

- “Activate outputs”, this parameter refers to the output that will be
activated
- “Deactiv. outputs”, this parameter refers to the output that will be
deactivated
The “Listen-in” and “Arming status” will have no effect if the respective command
is entered at a keypad.
•• Options - activated by means of and :
- Requires code - if enabled, the system will ask for user-code entry
before activating the shortcut. If the system recognizes the entered
user code, it will activate the shortcut command.
- SecurityRiskCode - if you enable this option, you must also enable the
“Requires code” option. When this option is enabled and the selected
shortcut involves a scenario that completely disarms a partition, or
switches a partition from Away mode to Stay mode, the security of
your system will obviously be at risk, therefore, the system will
request code entry.
- Confirm - if enabled, the system will ask the user for confirmation
CONTINUE?OK=YES
(press ) before activating the function-key shortcut. This method
draws the users attention to requested operations that do not require
codes, and thus avoids accidental arm/disarm operations, etc.

Via PC
Table 32: Keypads - via SmartLeague software application
Option Part of the system Template/section
Enable/disable / Project
ChoosePeripheral Keypads - select the keypad Programming

Readers 6-19
This section allows you to program the reader options.

Via Keypad
Type-in Code (Installer PIN) , PROGRAMMING Readers .

Enable/disable
This section allows you to add/remove readers to the I-BUS configuration, by
means of keys and .
This is a reader simulated by the Air2-BS100, a “W” will be shown at the end of
the description.
ChoosePeripheral
PROGRAMMING
This section allows you to program the various options of the selected reader. Expansions
• Description - editable field for the name of the digital key user. Keypads
• Partitions - use or to enable/disable the reader on the system Readers
partitions.
• Shortcuts - this section allows you to program the shortcuts associated with
the 4 differently-coloured LEDs on the reader. In order:
•• Red LED shortcut
•• Blue LED shortcut
•• Green LED shortcut
Readers
•• Yellow LED shortcut Enable/disable
The shortcut associated with the LED can be one of the following types: ChoosePeripheral
•• None Prog. Address
•• Arm/Disarm
•• Stop alarms
•• Clear call queue
•• Delete memory
•• Activate outputs
•• Deactiv. outputs Enable/disable
•• Overtime READER 001
•• Teleservice req. READER 002
READER 003

Options and programming methods 61

 Installation and Programming Manual

Prog. Address
This section allows you to activate the enrolling phase and program the
addresses of nBy/S and nBy/X.readers.
Follow the instructions for addressing readers in paragraph 3-3-3 Addressing nBy readers.

Via PC
Table 33: Readers - via SmartLeague software application
Option Part of the system Template/section
Enable/disable / Project
ChoosePeripheral Proximity readers - select the
Programming
reader
Prog. Address Proximity readers Programming

Sounderflashers 6-20
This section allows you to program the parameters of the sounderflashers
connected to the IBUS.
PROGRAMMING
Via Keypad Keypads
Type-in Code (Installer PIN) , PROGRAMMING Sirens . Readers
Sirens
Enable/disable
This section allows you to add/remove sounderflashers from the I-BUS
configuration, by means of keys and .
ChoosePeripheral
This section allows you to edit the description of each sounderflasher.
Sirens
Via PC Enable/disable
Table 34: Sounderflashers - via SmartLeague software application ChoosePeripheral
Option Part of the system Template/section
Enable/disable / Project
ChoosePeripheral Sounders - select the sounder/
Programming
flasher

Language 6-21
PROGRAMMING
Via Keypad Readers
This option allows you to select the language the system uses in the User and Sirens
Installer menus (fault/alarm descriptions, etc.). However, the edited descriptions Language
of the various system elements such as: zone, partitions, outputs, codes,
descriptions will remain unchanged.

Use keys or to select the desired language and to confirm.

Language
Italiano
English

Messages 6-22
This section allows you to record (and playback) all the voice messages. The
Table in the Appendix shows all the pre-recorded messages provided by the Record
SmartLogos30M voice board.
0034 sec.
Via Keypad
1. Accessing the “Messages” section:

Type-in Code (Installer PIN) , PROGRAMMING Messages .

2. Use keys or to select the field you wish to change, then use the
number keys ( , etc.) to edit the number.

62 Options and programming methods

Installation and Programming Manual

or
Use keys or to increase or decrease the number.
PROGRAMMING
Sirens
3. Press . Language
4. Use or to select the instructions for the selected message then Messages
press .

Record
Before recording a voice message, you must first select:
• No Message - no recording or playback
• High quality - for superior recording/playback quality Messages
• Average quality - for good recording/playback quality (similar to phone-line _01 Messages
quality). (Min. 00)
High quality messages occupy twice the memory space of average quality (Min. 485)
messages of the same length.

The recording will start when is pressed, the running recording time
(seconds) will be indicated by a second-counter on the keypad display. If you
wish to interrupt the record/playback operation manually press , otherwise, it
will end automatically when the pre-set time-out expires.
Messages
Play
Record
Message playback section. You can adjust the volume during the playback phase Play
using keys and . Delete
Delete
Delete message section. The control panel will ask for confirmation before
deleting the message, by means of the ( ) key.

Via PC
The Parameters settings template of the “SmartLiving System - Announcements” CODING
will allow you to: Empty message
• upload all the voice messages High quality
• download all the voice messages Average quality
• format voice board
Select an item from “SmartLiving System - Announcements” from the tree menu
on the left, then go to the “Parameters settings” template on the right and
program the selected message.

Default settings 6-23

This section allows you to reset to default settings all the control panel Serial port
parameters, auto-learn zone balancing values, auto-enroll I-BUS peripherals and
restore the event codes of CONTACT-ID reporting format.
Reset to default can be carried out at a keypad via the installer menu (details
follow), or via the control panel motherboard, using the following procedure.
1. Disconnect all power to the control panel (Mains and and battery power).
2. Short-circuit terminals “2” and “3” of the serial cable connector (refer to
Table 4: Control panels - description of parts, S). Terminals to
3 be short-
3. Power-up the control panel and maintain the short-circuit condition on ter- circuited
2
minals “2” and “3” for at least 5 seconds.
4. Restore the short-circuit condition.
Within 70 seconds the control panel will reset to default settings, re-enroll all the
peripherals currently on the I-BUS and, if a keypad is connected, will ask you to
select the Language.
Reset to factory default will not clear the events log.

Via Keypad
1. Access the “Default settings” section:

Type in Code (Installer) , PROGRAMMING Default settings .

2. Use keys or to select the function then press :

Options and programming methods 63

 Installation and Programming Manual

Factory data
If you select this option, the control panel will reset entirely to default settings.
This operations deletes all the previously programmed parameters. ATTENTION!
Learn zone bal.
(automatic acquisition of zone balancing settings)
If you select this option, the control panel will learn (save to memory) PROGRAMMING
automatically all the balancing settings of all the zones (Patent Pending). Language
The zone-balancing options are: Messages
• Normally Open Default settings
• Normally Closed
• Balancing (Single balancing)
• Double balancing
• Rollerblind with EOL
The balancing settings which are not acquired accurately are:
• Rollerblind without EOL (which is classified as a normally-closed generic zone) Default settings
• Double zone without EOL (which is classified as a normally-closed generic Factory data
zone) Learn zone bal.
• Double zone with EOL (which is classified as a generic zone with Double Auto enrolPeriph
balancing)
In order to allow accurate acquisition of the balancing settings of all the zones,
you must:
•• Wire and select the balancing settings of all the zones.
•• Ensure that all the zones are in standby status
•• Select the “Learn zone bal.” option.
•• Verify that the operation has been carried properly and that all the settings CONTINUE?OK=YES
are accurate (if any zones are not in standby status during this process
their settings will not be acquired accurately).
•• Set manually any inaccurate settings.
Auto enrolPeriph
If you select this option, the control panel will enroll automatically all the
peripherals it finds on the I-BUS.
CONTACT-ID only
If you select this option, the control panel will reset to default settings all the
event codes used for the CONTACT-ID reporting format.
DeletePrg.events
Press the key to delete all the events saved to the control panel events log
(activation and restoral events):
• All outputs
• All calls
• All options
WLS data reset
Press the key to delete all the data relating to the Air2-BS100 device.

The data relating to the wireless detectors and keyfobs will not reset on the control panel, Note
nor will the devices simulated by the Air2-BS100 transceiver be deleted from the
configuration.

3. The control panel will ask for confirmation of this command (press ).

User functions 6-24

This section describes the functions the installer has in common with the user.

Via Keypad
1. Access the “User functions” section:
Zone status
Type-in Code (Installer) , PROGRAMMING User functions . Zone n.77
Standby Unbypsed
2. Use keys and to select the User functions then press . Res. 03310 W

64 Options and programming methods

Installation and Programming Manual

View
PROGRAMMING
• Events log - allows you to view all the events saved to the log.
Messages
• Alarms log - allows you to view all the events relating to zone/partition alarm
and tamper saved to the log.
Default settings
User functions
• Faults log - allows you to view all the fault events saved to the log.
• Arm/Disarm ops. - allows you to view all the arm/disarm operations saved
to the log.
Use key or to scroll the chronological events list. For some events, key
allows you to view the partitions details. For example, the details of an “Arm”

command will show the code and keypad concerned and, if you press , the list User functions
View
of partitions involved. Outputs ON/OFF
• System voltage - allows you to view the voltage the system uses. Set date/time
• Zone status - allows you to view the status of all the zones. Use key or
to scroll the list of accessible zones.
The “Zone status” section allows you to view the zone status (“Standby”,
“Alarm”, “Shorted”, “Tamper”), the operating status (Unbypassed - able to
generate alarms, or Bypassed - unable to generate alarms) and also the
resistor value expressed in Ohm.
• Faults - allows you to view any current faults. VIEW
• Panel version - allows you to view the firmware version and model of the
Events log
SmartLiving control panel. Alarms log
Faults log
Outputs ON/OFF
Allows manual activation/deactivation of the outputs by means of keys and .
Set date/time
Allows you to set the date and time of the control panel.

1. Use key or to select the programming field you wish to change (hour,
Installer Code
minutes, etc.). 18:23 20/08/10
2. Use key or to change the value in the selected field.
KEYP. 001
3. Press to save and exit.

Via PC
Table 35: User functions - via the SmartLeague software PanelVersion
application
Option Part of the system Template/section 1.00 01050
View/Log SmartLiving system - Log Programming
Set date/time SmartLiving System Programming

Other parameters 6-25

Allows you to program the advanced functions of the control panel.

Via Keypad
1. Access the “Other parameters” section.

Type-in Code (Installer PIN) , PROGRAMMING Other parameters .

2. Use key or to select the parameter then press .

Periodic event
This parameter allows you to set the time (hh/mm), day, month and year of the
first “Periodic event” (refer to paragraph 6-9 Events).

The time/date setting of this parameter must be later than the control panel clock setting. Note
PeriodicInterval
This parameter allows you to set the interval between “Periodic events”
(expressed in hours).
To disable the “Periodic event”, set “0”.

Options and programming methods 65

 Installation and Programming Manual

Mains fail.Delay
If this value is
This parameter allows you to program the delay, expressed in minutes (see
“info” box ), between mains failure and the “Mains failure” fault event signal. expressed in minutes,
there is an error
LocKpadMessTimes margin of 1 minute (for
The number of times messages, relating to the events recorded on the keypad, example, if you set 5 minutes,
will be played (JOY/MAX keypads only). the period can vary between 4
The playback phase can be stopped by pressing any key. If you set a value of and 5 minutes).
“255” the playback can be stopped by pressing any key, this is the only method
of stopping playback.
OverThePhoneVol.
This is the volume of the voice messages over-the-phone.
OverThePhoneVol.
00_ Units
Ring sensitivity (Min. 010)
This value determines the reception sensitivity of incoming call rings. This option (Max. 100
is useful in situations of bad reception (break up) or noisy lines.
At default this value is set at 50. Accepted values: 1 to 100. The higher the value
the higher the sensitivity.
Wireless superv.
This value determines the wireless-detector supervision time. Once the pre-set Tel. input gain
time expires, the detectors which do not respond will be signaled as lost. 00_ Units
Accepted values: 12 to 250 minutes. (Min. 001
Tel. input gain (Max. 080)
This value determines the volume of the incoming call signal. This option is useful
in situations which require better comprehension of DTMF tones and
improvement of teleservice intervention via modem.
Adj. temperature
This parameter will allow you to enter the effective value of the room
temperature read by an external thermometer.. This value will replace the
keypad temperature reading and thus allow you to correct the temperature
sensor on the keypad you are working on (Joy/MAX only).
The entered value must be expressed in °C decimals (for example, type in 252 if
the temperature is 25.2 °C). If this value is
LowBattDelay expressed in minutes,
there is an error
This parameter will allow you to program the delay, expressed in minutes, which margin of 4 minutes (for
will be applied before “LowBattery” events are signaled.
example, if you set 7 minutes,
LinedownDelay the period can vary between 3
This parameter will allow you to program the delay, expressed in seconds, which and 7 minutes).
will be applied before “LineDownDelay” events are signaled.

All the above-mentioned parameters can be programmed as follows.

PROGRAMMING
3. Use key or to select the field you wish to change, then use the Default settings
number keys ( , etc.) to edit the number. User functions
or Other parameters
Use key or to increase or decrease the number.
FaultNotReady
This section allows you to select which events, other than zones in alarm status,
will be signaled as system security-risk conditions when the partition arms.
Following are the events which can be enabled/disabled by means of keys Other parameters
and :
Periodic event
• Zone fuse fault PeriodicInterval
• IBUS fuse fault Mains fail.Delay
• Low battery
• Mains failure
• Tel. line down
• Jamming
• Low battery WLS
• WLS zone loss
18:23 20/08/10
• LossTamp.ongoing
EU dd/mm/yyyy

66 Options and programming methods

Installation and Programming Manual

The last item groups the following events:

•• Panel opened
•• Dislodged panel
•• Expansion tamper
•• Keypad tamper
•• Reader tamper
•• Siren tamper
•• Expansion loss
•• Keypad loss
•• Reader loss
•• Sounderflasher loss

4. Press to confirm and exit.

Via PC
Table 36: Other options - via the SmartLeague software application
Option Part of the system Template/section
Periodic event
Parameters settings - periodic event
PeriodicInterval SmartLiving System
Mains fail.Delay Parameters settings - I-BUS parameters
LocKpadMessTimes Keypads Parameters settings - Keypad parameters
OverThePhoneVol. SmartLiving System Parameters settings - Telephone options
Ring sensitivity Parameters settings - Telephone line
SmartLiving System - Telephone
parameters
Wireless superv. Parameters settings - Control panel
parameters
SmartLiving System
Tel. input gain Parameters settings - Telephone options
LowBattDelay Parameters settings - I-BUS parameters
LinedownDelay Parameters settings - Telephone dialer
SmartLiving System - Telephone parameters
FaultNotReady SmartLiving System Parameters settings - 50131 Parameters

Telephone line adjustment 6-25-1

The “OverThePhoneVol.” and “Tel. input gain” parameters can be used to correct
the voice functions of the dialer and the DTMF tones. The values of these
parameters affect each other, therefore, and a good result is always a
compromise.
If you are not using a GSM interface, you should:
• Adjust one parameter at a time and carry out tests to verify the result.
• Increase/decrease the values in small steps (for example, from 25 to 22 and
not from 25 to 15).
• If the DTMF tones are not recognized, or are recognized with difficulty,
decrease the value of the “Volume Tel.voice” parameter (in small steps of 2
or 3 units) and verify the effect. If there is no improvement, increase the
value of the “VolumeTel. In.” parameter until an acceptable combination is
achieved.
Do not increase the “VolumeTel. In” parameter excessively, as an excessive
value may cause incorrect interpretation of DTMF tones.
• If the volume of the telephone messages is low, increase the “Volume
Tel.voice” (in small steps of 1 or 2 units) and verify the effect. An excessive
value of the “Volume Tel.voice.” parameter may cause incorrect
interpretation of DTMF tones.
In most cases, the value of the “Volume Tel.voice” parameter is between 15 and
25, whereas, the value of the “VolumeTel. In.” parameter is between 20 and 30.
If you are not using a SmartLink GSM interface, you should:
• If the DTMF tones are not recognized, or are recognized with difficulty,
increase the value of the SmartLINK “VolumeTel.In” parameter by 1 or 2
notches over the medium value “M” then verify the effect. If there is no
improvement, decrease the value of the “VolumeTel.In.” parameter of the
SmartLiving control panel until an acceptable combination is achieved..

Any changes to the value of the SmartLink “VolumeTel.In.” parameter come into effect Note
almost 2 minutes after the setting change, therefore, you must allow this time to pass
before verifying the effect.

Options and programming methods 67

 Installation and Programming Manual

Chapter 7

ERRORS AND
FAULTS

Communication BUS 7-1

(I-BUS)
The control panel monitors the I-BUS continuously.
If no signals (control panel and peripheral signals) are detected on the I-BUS for
over 40 seconds, the keypad displays will show the warning opposite. The display - JOY/MAX -
will show the: FW RELEASE 1.00
1. Keypad model NO COMMUNICATION
2. Keypad firmware version K01 P14
3. Error type
4. Keypad address and built-in reader address (Joy/MAX only)
First check that cable “D” of the I-BUS is connected properly. Then check the
proper operating capacity of the I-BUS and the general integrity of the entire
system.
- JOY/MAX -
If the message opposite appears on the keypad display, it means that I-BUS is FW RELEASE 1.00
operating properly but cannot communicate with the keypad in question.
NOT ENROLLED
Therefore, the keypad is not present in the system configuration. K01 P14
One of the two messages shown in the figures may also appear during the control panel Note
firmware updates.

LED activity 7-2

The blue and yellow LEDs on the control panel motherboard (refer to Table 4:
Control panels - description of parts, X) may help in providing information
regarding the proper operating capacity of the control panel firmware and I-BUS,
as follows.
Blue LED
If the control panel is operating properly, the blue LED on the motherboard will
blink rapidly. However, at the end of a programming session via keypad or PC, or
during restoral of default settings or re-programming operations, the LED may be
either On solid or Off. It will blink rapidly once the operation is completed.
If the LED is On or Off permanently for no apparent reason (see above), it means
that all the system functions are blocked.
Shut the system down and contact your dealer immediately.
Yellow LED
If the control panel is operating properly, the yellow LED on the motherboard
should flicker. However, at the end of a programming session via keypad or PC,
or during restoral of default settings or re-programming operations, the LED may
be either On solid or Off. It will blink rapidly once the operation is completed.
If the yellow LED is On or Off permanently, it means that there is trouble on the
I-BUS.
If the LED is On or Off permanently for no apparent reason (see above), it means
that the I-BUS is blocked. This condition is confirmed by the loss of
communication with the keypads, readers and expansions.
Check the integrity of the I-BUS line.

68 Errors and faults

Installation and Programming Manual

Ring Sensitivity 7-3

The various configurations of modern telephone lines and the multiplicity of
signals that transit along them, require major attention in the design of phone-
line interfaces. The optimized phone-line interface on-board SmartLiving control
panels has been especially designed to satisfy present day requirements. In
addition to the traditional telephone plug for land line (PSTN) connections, there
are usually boards for ISDN or ADSL connections.
If there are ADSL filters on the line, it will be necessary to connect the control
panel downstream of the filters, to the line dedicated to telephone equipment
(this line is clearly indicated on the filters).
Following are two “trouble” conditions which may be caused by ISDN or ADSL
connections, etc. , and the “actions” you must take if you encounter such
problems.
• Problem - The control panel is enabled for “Answerphone” and “Teleservice”
functions but fails to pick up incoming calls after the programmed number of
rings or picks up after more rings than programmed. Answer - Increase the
value of the “Ring Sensitivity” parameter to a suitable level.
• Problem - The control panel is enabled for “Answerphone” and “Teleservice”
functions but picks up during “through” calls (calls that should not involve the
control panel). Answer - Decrease the value of the “Ring Sensitivity”
parameter to a suitable level.

Errors and faults 69

 Installation and Programming Manual

Appendix A

TECHNICAL TERMINOLOGY
AND GLOSSARY

A terminal configured as a Controlled Output (I/O, input-output) is capable of reading the I/O TERMINAL
status of the output.
This configuration can be used for creating automations, for example the condition of an
alarm condition on “AND” zones:
• the single alarm events of two zones activate respectively an output terminal and an I/O
terminal
• both the outputs are monostable, for example at 30 seconds
• the terminals are shorted
The input section of I/O terminals triggers the alarm actions (calls and sounderflashers), only
when the two zones are both violated (AND) within the monostable time of the outputs.
This device allows the control panel to send voice calls to programmed contact numbers. VOICE DIALER
In SmartLiving control panels the voice dialer function is provided by the SmartLogos30M
board (accessory item).
Violation of a zone with this attribute will generate an instant alarm even when the partitions it 24 HOUR ZONE
belongs to are disabled. The system will generate the respective alarms which will be shown
on the keypad.
These zones usually monitor conditions that are not directly connected to intrusion control.
For example, Water tank overflow and flooding detectors are usually configured as 24H zones.
These are 4, 5 or 6 digit PINs which allow the building occupants (users) to access the system. ACCESS CODES
Each code can be programmed to control specific functions only, and to operate the system to
suit the requirements of the Main user.
Code types
• Installer code:used by the installer company technician
• User code:assigned to the building occupants
Detection of non-authorized entry into the protected building. More specifically, activation of ALARM
alarm signaling devices (detectors).
A parameter generally associated with zones. This value determines the number of alarm ALARM CYCLES
events a zone can generate before the partitions it belongs to disarm. This value (number of
alarm events) resets to zero when the zone partitions re-arm or reset.
If a zone is allowed to generate an unlimited number of alarm events, it is classified as a
“repetitive” zone.
In the event of: ALARM OR TAMPER
• Zone Alarm MEMORY
• terminal tamper
• open panel or dislodged panel
• peripheral tamper (keypads, expansions, readers)
• peripheral loss (keypads, expansions, readers)
• false key
The red LEDs on the system keypads and readers go On each time one of the previously-
mentioned events occur. This visual warning signal is held even after the event ends (alarm
memory), in order to warn you that an event occurred during your absence. This visual
warning signal will be held until you clear the event memory (refer to Delete Memory).
This is a private company that monitors premises protected by intrusion control systems ALARM RECEIVING
equipped with Digital or Voice dialers (refer to Digital dialer and Voice dialer).
CENTRE (ARC)
Alarm Receiving Centres receive alarm reports from monitored systems and take all the
necessary actions to protect the occupants of the protected premises.
The “Answerphone” function, if enabled by the user, allows the control panel to answer ANSWERPHONE
incoming calls after a pre-set number of rings. The control panel will pick-up and play the
recorded answer message.
During the call, the recipient can type-in a valid PIN (enabled for over-the-phone control) and
access the authorized functions.
User operations on one or more partitions. These generally indicate also the status of the ARM/DISARM
partitions. Under normal circumstances, the zones of armed partitions can generate alarms.
Under normal circumstances, the zones of disarmed partitions cannot generate alarms. The
system generates tamper alarms even when partitions are disarmed.
You can enable/disable the Auto-arm function on each separate partition. AUTO-ARM
If the auto-arm option is enabled on a timer-controlled partition, the partition will arm/disarm
in accordance with the ON/OFF settings of the timer.

70 Technical terminology and Glossary

Installation and Programming Manual

A zone with this attribute will be bypassed automatically by the control panel if the partition it AUTO-BYPASSABLE
belongs to arms when the zone is not in standby status.
ZONES
The zone will be unbypassed automatically when it restores to standby or when the partition it
belongs to is disarms.
This is the secondary power source of the system. If primary (230 Vac) power failure occurs, BACKUP BATTERY
the battery will take over.
SmartLiving control panels use sealed lead batteries. The battery housing determines the
maximum size of the battery and therefore, its power-storage capacity. SmartLiving control
panels provide housing for one battery @12V 7Ah. The control panel monitors the battery
continuously and keeps it is under constant charge (from Mains).
Connection of a zone to a terminal configured as an input. BALANCING
It is necessary to program the balancing of each separate zone and wire the terminal
accordingly. The SmartLiving intrusion control panel provides 6 different types of balancing, as
follows:
• Normally Open
• Normally Closed
• EOL
• DEOL
• Double zones (only terminals with DOUBLING configuration)
• Double zones with EOL (only for terminals with DOUBLING configuration)
DEOL and customized zones can discriminate 4 conditions:
• Short-circuit
• standby
• alarm
• tamper
If you observe the Events list, you will see that there is an alarm event for each zone and a
tamper event for each terminal. This is because a terminal configured as a double zone (or
double zone with EOL) must be able to discriminate between alarm and standby conditions on
each single zone, whereas tamper and short-circuit conditions involve the entire terminal and
not the single zone.
An output, that once activated, requires an explicit command to deactivate it. BISTABLE OUTPUT
Generally, bistable outputs are used to provide immediate signaling (in real-time) of specific
events that occur on the system. For example, if the “Mains Failure” event is associated with
a bistable output that is connected to a LED, the LED will signal the event immediately.
These zones operate in the same way as 24h zones, but do not generate partition alarms or BUILDING
visual signals on the system reader and keypad LEDs.
AUTOMATION ZONE
Zones configured in this way can be used for automation applications.
A list of outgoing event-associated calls the control panel must send to programmed contact CALL QUEUE
numbers.
Enabled users can clear the call queue manually.
A zone with this attribute will generate "Chime on partition" events, if violated when the CHIME ZONE
partitions it belongs to are disarmed.
Keypads which have partitions in common with the chime zone will emit an audible signal
when the "Chime on partition" event occurs. If all the partitions the zone belongs to are
armed, the zone will operate as programmed. This function is widely used in commercial
buildings (shops, etc.), and is generally associated with the zone that monitors the entrance to
the premises in order to signal the arrival of customers.
Activation of a zone with this configuration generates the command it is assigned to. COMMAND ZONE
SmartLiving control panels manage the following commands:
• Disarm zone: if activated, it will disarm all the partitions it belongs to. Zones configured in
this way can be used to disarm partitions by means of a keyswitch.
• Arm zone: if activated, it will arm all the partitions it belongs to. For example, keyswitches
are usually configured as command zones.
• OnArm/OffDisarm zone: if activated, it will generate an arm-partitions command and,
the instant it restores to standby, a disarm-partitions command. The command will affect
only the partitions the zone belongs to. Zones configured in this way can be used to arm/
disarm partitions by means of a keyswitch.
• Switch zone: if activated when all the partitions it belongs to are disarmed, it will arm all
the partitions. If activated when even one of the partitions it belongs to is armed, it will
disarm all of its partitions. The command will affect only the partitions the zone belongs to.
Zones configured in this way can be used to arm/disarm partitions by means of a
keyswitch.
• Patrol zone: if activated, it will have a patrol function in all the partitions it belongs to.
A group of operating parameters set at the factory by the manufacturer. The purpose of these DEFAULT SETTINGS
settings is to reduce the work of the installer during the installation phase.
The installer can restore the system to “Default Settings” if necessary.
Violation of a zone with this configuration will not generate an alarm but will trigger the DELAYED ENTRY
associated Timer (Entry time). If the user does not disarm the partition/s within the set “Entry
time”, the system will generate an alarm. ZONE
For example, the zone that monitors the main door of a building is usually configured as a
Delayed Entry Zone, in order to give building occupants time to enter the building and disarm
the partition without generating an alarm.

Technical terminology and Glossary 71

 Installation and Programming Manual

Violation of a zone with this configuration will not generate an alarm but will trigger the DELAYED EXIT ZONE
associated Timer (refer to Exit time).
For example, the zone that monitors the main door of a residence or building is usually
configured as a delayed exit zone, in order to give occupants time to leave the partition after
an arming operation. If the user does not leave the zone within the set “Exit time”, the system
will generate an alarm.
This is an explicit user-command which ends signaling on the red keypad/reader LEDs of the DELETE ALARM/
following events:
TAMPER MEMORY
• zone alarm
• terminal tamper
• open panel or dislodged panel
• peripheral tamper (keypads, expansions, readers)
• peripheral loss (keypads, expansions, readers)
• false key
If you delete the alarm/tamper memory, the visual signals on the red reader/keypad LEDs will
clear.
This device allows the control panel to send report calls to Alarm Receiving centres (ARC). DIGITAL DIALER
SmartLiving control panels provide a built-in digital dialer which supports all the most widely
used protocols.
An electrical input point used for the management/supervision of signals coming from 2 DOUBLE ZONE
intrusion detection devices.
The terminal the zone is connected to must be configured as a “double input zone". Terminals
with this configuration allow the system to distinguish between two distinct alarms coming
from the two different zones it is connected to.
The time (expressed in minutes or seconds) that the system allows the user to disarm the ENTRY TIME
partition after zone violation. It the system is not disarmed within the set time it will generate
an alarm. (OR ENTRY DELAY)
Each partition can be programmed with its own Entry time.
A status or operative mode recognized by the system. EVENT
For example: detector alarm, mains failure, user-code recognition, etc.
Each event (e.g. mains failure) can be associated with an activation event (when the event
occurs) and a restoral event (when the event ends).
Each event can be programmed to generate the following actions:
• activation of one or more outputs
• transmission of one or more e-mails
• activation of one or more voice calls
• activation of one or more digital calls
For example, it is possible to activate output 3 when the event starts and to activate output 5
when it restores.
This is the non-volatile portion of the memory the panels saves events to. The events are EVENTS LOG (OR
saved in chronological order with the following details:
EVENTS MEMORY)
• event description - with details regarding new events and restorals
• information regarding the user or the cause of event
• event location
• event date and time
The events log can be viewed by the system users and the installer.
Partition events (zone alarms, partition alarms, arm/disarm operations, recognized codes and
keys, etc.) can be viewed by users with at least one partition in common with the event
element.
For example, if a user arms several partitions from a keypad, the events log will show:
• description of the event - “Arm request”
• description of the code and partitions involved
• description (label) of the keypad involved
• date and time of the request
A short period (expressed in minutes or seconds) during which the user must disarm the EXIT TIME
partition after violation (for example, after opening the front door) otherwise the system will
generate an alarm. (OR EXIT DELAY)
Each partition can be programmed with its own Exit time.
These boards can be used to increase the number of terminals (zones or outputs) and/or the EXPANSION BOARDS
size of the system (in order to extend it over a larger area). Expansion boards can be
connected to the system via the I-BUS. (FLEX5)
The Flex5 expansion has:
• 5 fully-programmable terminals
• a Buzzer (for audible signals)
• 1 analogue output
A condition which indicates that a system component is not working properly. FAULT
Some faults can jeopardize the performance of the entire system. Mains failure (230V a.c.),
telephone line-down and low battery are typical faults.
This type of zone usually comprises a motion detector which senses for the presence of GENERIC ZONE
movement in the protected partition. For example, PIRs, Double technology detectors,
magnetic contacts on doors and windows.

72 Technical terminology and Glossary

Installation and Programming Manual

This device allows the system to send calls over the GSM network. GSM INTERFACE
The SmartLink is a custom GSM interface for INIM control panels. This device is capable of
providing the control panel with a telephone line even in the event of telephone line tamper
(line cutting). This function increases the level of security considerably.
This is the two-way communication line (4 wires only) which connects the peripheral devices I-BUS
(keypads, readers, expansions, etc.) to the control panel.
The 4 easily identifiable wires, on the control panel motherboard and on the expansions, are:
• “+” power 12 Volt
• “D” data
• “S” data
• “-” Ground
The Installer code is identified by a 4, 5 or 6 digit PIN. This PIN allows the installer to access INSTALLER CODE
the system Programming Menu either from a keypad or via the respective software
application, on condition that all the system partitions are disarmed.
List of system functions and respective parameters accessed via keypad. INSTALLER MENU
This menu allows the installer to program, check and change nearly all of the system
parameters. The Installer Menu can be accessed from any keypad or via computer with the
SmartLeague software application, on condition that all the system partitions are disarmed.
Violation of a zone with this attribute will generate an immediate alarm (no delay). INSTANT ZONE
A zone that monitors the inside of the protected building. INTERIOR ZONE
For example, the interior zones of an office building are the zones that monitor offices and
entrance points.
If a partition that a zone belongs to is armed in Stay mode, it will be unable to generate
alarms.
A control device (card or keyfob) which allows the authorized user to access the system. KEY
The key must be held in the vicinity of the reader in such a way to allow the system to read it
and permit access to authorized operations.
Each key is programmed with:
• A random code selected from over 4 billion possible combinations.
• A label (usually the name of the user).
• The partitions it controls (arms, disarms, etc.).
• A group of pre-set parameters which allow the key user to operate the system in
accordance with the authorized access level (for example, a key can be programmed to
arm or disarm the system only at certain times of the day).
This device allows users to access and control the system. Keypads can be connected to the KEYPAD
system via the I-BUS.
(JOY)
The keypad is equipped with:
• LCD graphic display
• 2 terminals
• alphanumeric keys for code and data entry
• LEDs for visual signals
• a buzzer (for audible signals)
• microphone and speaker (Joy/MAX only)
• built-in reader (Joy/MAX only)
• temperature sensor (Joy/MAX only)
The keypad allows users to access and control the partitions which are common to both the
code and keypad in use. The user can arm/disarm partitions, view the status of the zones,
stop visual and audible signaling devices.
A generic magnetic-contact is a detector/sensor based on an magnet which, when placed near MAGNETIC CONTACT
the sensor, provokes the mechanical closure of an electrical contact.
(AIR2-MC100)
The Air2-MC100 wireless device comprises a magnetic-contact with 2 terminals (T1 and T2)
which can be configured as either inputs or outputs. The magnetic-contact is equipped with a
horizontal magnetic sensor and a vertical magnetic sensor, positioned along the sides of the
device.
If you wish to carry out maintenance work on the control without generating false alarms MAINTENANCE
(tamper and intrusion), you must put the control panel in “Maintenance” mode. The control
panel in must also be in “Maintenance” mode during the keypad and reader addressing
process. The other functions of the control panel are still available (arm/disarm operations,
events, calls, etc.).
An output, that once activated, does not require an explicit command to deactivate it. This MONOSTABLE
output must be programmed with a timeout (Monostable time expressed in seconds or
minutes). Once activated, this output will remain active until the pre-set Monostable time OUTPUT
expires.
Generally, monostable outputs are used to provide continuous signaling of the events they are
associated with. For example, if the “Alarm Partition 1” event is associated with a monostable
output with a 2 minute timeout, the output (sounder) will signal the event for 2 minutes then
will deactivate automatically.
An advanced wireless-technology system in which the control panel and its devices are ONE-WAY WIRELESS
equipped with a transceiver module. If a detector senses an alarm condition, it will generate a
number of event transmissions which under the right circumstances should reach the control SYSTEM
panel.

Technical terminology and Glossary 73

 Installation and Programming Manual

An electrical output point connected to a signaling or control device activated/deactivated by OUTPUT

the control panel in response to programmed events.
The terminal the device is connected to must be configured as an “output”.
Outputs are usually connected to audible or visual signaling devices but can be used for other
purposes such as: switching on lights or opening doors/gates.
A group of zones. PARTITION
A partition identifies a group of zones that belong to a spatial or logical portion of the protected
premises. For example, a partition may comprise all the zones that protect the downstairs
partition of a house (spatial partition), or all the entrances of an office building (logical
partition).
This refers to the status of a partition as requested by the user. PARTITION ARM/
The user can carry out the following operations. DISARM OPERATIONS
• Disarm - this operation disables the partition completely. In this way, none of the zones
belonging to the partition can generate alarms.
• Away mode - this operation enables the interior and perimeter zones of the partition. In
this way, all of the zones of the partition can generate alarms.
• Stay mode - this operation enables only the perimeter zones of the partition. In this way,
only the perimeter zones of the partition can generate alarms.
• Instant mode - this operation enables the partition perimeter zones only and annuls
delays. In this way, violation of the perimeter zones of the partition will generate instant
alarms.
• Hold - this operation forces the partition to hold its current status.
A periodic inspection of the protected premises carried out by authorized security staff. PATROL
Patrol staff can disarm each partition for the pre-set time only (programmable separately for
each partition). The partitions concerned will rearm-as-before automatically when the pre-set
time expires. Persons involved in periodic security inspections require codes with the "Patrol"
attribute.
If the system receives a partition disarm command (generated by a code or key) while the
patrol time is running, the “Patrol” function will be interrupted immediately. In this case, when
the patrol time expires the partition will not be re-armed automatically and therefore, will be
disarmed.
A zone that monitors the entrance points of the protected building. PERIMETER ZONE
Perimeter zones are usually direct entrance points such as doors and windows. For example,
the front door of an apartment and windows that allow access from outside.
Devices connected to the control panel via the I-BUS. PERIPHERALS
SmartLiving control panels manage the following peripherals:
• JOY series Keypads
• Proximity Readers (nBy)
• Expansions (Flex5)
• Transceiver (Air2-BS100)
• Sounder (Ivy)
The period (expressed in minutes) before an automatic arming operation. PRE-ARM TIME
For example, if a partition is set to arm automatically at 10:30 with a Pre-arm time of 5
minutes, all the partition keypads and readers will initiate an audible countdown at 10:25 in
order to warn users of the forthcoming arming operation.
Each partition can be programmed with its own Pre-arm time.
The installation site. PREMISES
Identifies the building or part protected by the intrusion control system, generally, a house or
office.
Under normal circumstances, the mains power supply (230Vac) 50 Hz (110V a.c. 60Hz in PRIMARY POWER
some countries).
SOURCE
Usually connected to a switching power supply or transformer (depending on the model) that
provides the stabilized voltage to the system and the charge source to the batteries.
This device allows users to access and control the system. The system readers are connected READER
to the control panel via the I-BUS.
(NBY)
Readers are equipped with:
• LEDs for visual signals
• a buzzer for audible signals (nBy/S only)
• key reader (TAG)
The key (TAG) allows the user to activate shortcuts (refer to Shortcuts) and arm/disarm the
partitions which are common to both the key (TAG) and reader in use. The key (TAG) must be
held in the vicinity of the reader in such a way to allow the system to read it and permit access
to authorized operations. Although readers provide a more limited access to the system, they
are easiest way of carrying out day-to-day operations (arm, disarm, etc.).
This type of zone comprises a sensor that detects any movement of the protected rollerblind. ROLLERBLIND ZONE
Violation of a zone with this configuration will not generate an alarm during the pre-set Entry ROUTE ZONE
time (refer to Entry time).
For example, the zones that monitor the way to a command device (Keypad/Reader) are
usually configured as Path Zones, in order to give building occupants time to enter the
building, reach the command device (Keypad/Reader) and disarm the partition without
generating an alarm.
Violation of a zone with this configuration will generate an instant alarm if the Entry time
(Entry delay) has been revoked (as per Stay Mode).

74 Technical terminology and Glossary

Installation and Programming Manual

A pre-set arming configuration which applies various operating modes to the system SCENARIO
partitions.
Following is an example of a pre-set scenario:
• Partition 1Disarm
• Partition 2Away arm
• Partition 3Stay arm
• Partition 4Hold
• Partition 5Disarm
SmartLiving control panels can be programmed (by the installer) with as many as 30 scenarios
in accordance with user requirements.
The “Arm/disarm” shortcut must always be associated with one of the 30 available scenarios.
When the system applies the selected scenario, the partitions will arm accordingly.
This type of zone usually comprises a shock detector (e.g Glassbreak detector) which senses SHOCK ZONE
for shock waves (vibration caused by hard blows).
The shortcuts allow quick access to User Menu options which normally require several step-by- SHORTCUTS
step operations.
For example, to activate/deactivate an output manually, you must:
1. Type in a user code.
2. Access the User Menu.
3. Select the option (activate outputs).
4. Select the required element (output).
5. Activate/Deactivate the selected element (output).
Instead, the “Activate outputs” and “Deactiv. outputs” shortcuts allow you to activate/
deactivate an output by simply pressing a single key or, if required for security reasons, after
entering a user code.
The shortcuts can assigned to:
• keypads
• codes (entered at the keypad or via remote telephone)
• readers
• keys
Some shortcuts (for example, “Activate Outputs”) require details before the system can
implement them. These details (parameter, value, etc.) depend on the source of the shortcut
command (keypad, code, reader, keys).
Refer to the details in the Appendix B, Technical terminology and Glossary shortcuts list.
Shortcuts 0 to 8 implement their associated actions instantly whereas, shortcuts 10 to 35,
which can be activated from keypads only, access the menu section specified by the user.
Activation of a zone with this configuration generates an immediate alarm even when the SILENT ZONE
partition it belongs to is disabled. Furthermore, audible and/or visual signaling devices will not
be activated (silent alarm), therefore, even calls generated by the alarm will not be revealed. (OR DURESS ZONE)
Under normal circumstances zones with this attribute are activated manually (using hidden
buttons or similar devices) in situations of duress (armed robbery, etc.).
If you wish to create a silent alarm zone, simply assign the “Silent” attribute to the zone alarm
event.
Spot events are events that restore automatically immediately after their activation. Some of SPOT EVENTS (PULSE
the previously mentioned events are spot events.
EVENTS)
For example, the “valid code” event activates as soon as the code is entered at the keypad,
therefore, it is impossible to determine its restoral as it starts and ends instantly.
Pulse events (Spot events) can be programmed to activate:
• an output and calls when the event occurs
• an output when the event restores (only if the output has the option “ON afterRestoral”
activated)
Under normal circumstances, spot events are assigned to monostable outputs (Refer to
Monostable Outputs).
An output that is monitored and therefore allows verification of its improper operating capacity SUPERVISED OUTPUT
(unsuccessful activation/deactivation).
The “supervision time” is the interval during which the wireless-system devices (in general SUPERVISION
wireless detectors in permanent placements) must signal to the control panel that they are
operating in the network. If a wireless device fails to signal before the “supervision time”
expires, it will be classified as “Lost” and the control panel will trigger a “peripheral-loss” fault
event.
Detection of a serious condition that jeopardizes the operating capacity of the device TAMPER
concerned and thus puts the system at risk.
Tamper conditions are detected by tamper switches connected to the system zones, keypads,
readers, expansions and control panel. Generally, these events are triggered by system
violation such as unauthorized opening of a keypad cover.
These are calls sent to programmed contact numbers when specific events start and end TELEPHONE ACTIONS
(restoral).
This is a service provided by the installer company. The installer company requires the user's TELESERVICE
collaboration and authorization before opening a teleservice session and working on the
system via telephone line.

Technical terminology and Glossary 75

 Installation and Programming Manual

A screw terminal for the connection of zones (detection devices) and/or outputs (command/ TERMINAL
signaling devices).
The terminals (with some exceptions) of the control panel, keypads and expansion boards can
be configured as:
• Input zone
• Double zone (ZONE DOUBLING)
• Output
• Supervised output
• Unused terminal
A zone with this attribute cannot generate alarms (activate audible and visual signaling TEST ZONE
devices). However, any alarm events that occur will be saved to the events memory.
The installer usually assigns the “test” attribute when the system is undergoing tests, in order
to avoid false alarms. In this way, the installer can see if a zone is operating properly by
simply referring to the events log.
A logical entity for automatic time-management of programmed peripherals or elements. TIMER
SmartLiving control panels provide 10 timers.
Each timer can be programmed to manage:
• An activation time (ON Time) and a deactivation time (OFF Time) on preset days of the
week and specific dates.
• 5 timer-slot exceptions. Each "exception" refers to a specific interval of one or more days,
which can be programmed with an ON and OFF Time.
The timers can be used for different purposes:
• If a timer is associated with a partition, the system will arm and disarm the partition
automatically in accordance with the On/Off settings of the timer.
• If a timer is associated with a code, the latter will be allowed to access the system only
when the timer is On.
• If a timer is associated with a key, the latter will be allowed to access the system only when
the timer is On.
• If the “Timer xxx” event is assigned to an output, the latter will activate/deactivate the
connected device in accordance with the On/Off settings of the timer.
No matter how they are employed, the timers must always be enabled by the user.
Transceiver-equipped devices TRANSCEIVER
In two-way wireless systems, all the devices are equipped with transceivers. In one-way
wireless systems, the main unit is equipped with a receiver module whereas the peripheral
devices are equipped with transmitters.
A wireless-technology system in which the control panel and its devices are equipped with a TWO-WAY WIRELESS
transmitter module and a receiver module.
SYSTEM
These systems are more reliable than one-way wireless systems as each device transmission
is validated by a reverse transmission.
A zone with this attribute cannot be bypassed, manually (by the user) or automatically (by the UNBYPASSABLE ZONE
control panel).
This attribute is usually assigned to high-security zones.
If a terminal is configured as an "unused" terminal, it will not be included in the terminal UNUSED TERMINAL
configuration (total sum of control panel terminals).
This ensures that any "Unused" terminals on the expansion boards and keypads are still
available for use.
Each code is programmed with: USER CODE
• A 4, 5 or 6 digit PIN which allows access the system.
• A label which identifies the user (usually the user's name).
• The group of partitions it controls (arms, disarms, etc.).
• A group of pre-set parameters which allow the operator to work on the system in
accordance with its authorized access level (for example, a code can be enabled to consult
the events log but not to change the date and time).
List of functions available to the user after valid code entry at a keypad. USER MENU
This is a delayed entry and exit zone and does not generate alarms when violation occurs VIEWABLE DELAYED
during the running entry/exit time, however, the violation will be signaled on the keypad.
ZONE
If the system is equipped with a SmartLogos30M voice board, each JOY/MAX keypad, in the VOICE MEMO
system configuration will allow users to record memos. Memos can be recorded, played and
deleted as required.
An intrusion control system whose devices (detectors, keypads, keyfobs) communicate with WIRELESS
the control panel over radio waves.
Usually, only the control panel of wireless-systems is mains powered (220Va.c.) while, the
wireless devices are battery powered. The battery life is of utmost importance in the design
layout and operational capacity of these systems.
An electrical input point used for the management/supervision of signals coming from an ZONE
intrusion detection device. The terminal the zone is connected to must be configured as an
“input” zone.
Zones are usually connected to a single device, however, it is possible (if the zone is duly
wired and configured) to connect more than one device. If a zone is connected to more than
one device it is impossible to identify the alarm-trigger device in the event of an alarm.

76 Technical terminology and Glossary

Installation and Programming Manual

The conditions which generate a zone alarm, on the understanding that the zone belongs to ZONE ALARM
several partitions, are as follows: the zone must detect violation and all the partitions it
belongs to must be armed.
Zone alarms provoke activation of audible and visual signaling devices (sounders, flashers,
reader/keypad LEDs, etc.) and generate voice and digital calls. Zone alarm events
automatically generate partition alarm events on all the partitions the zone belongs to.
A violated zone will not generate alarms if:
• it belongs to several partitions and one of them is disarmed
• it is bypassed (disabled)
• it is in test status (the event will be saved to the events log only)
• it an “interior” zone, and one of the partitions it belongs to is armed in Stay or Instant
mode
A bypassed zone (disabled zone) cannot generate alarms. Each zone can be bypassed/ ZONE BYPASS/
unbypassed manually by the system users, or automatically by the control panel. Automatic
bypass operations can take place only when the zone is configured as “Auto-bypassable” and UNBYPASS
the conditions that regulate auto-bypass operations are in effect (refer to Zone Attributes –
Auto-bypassable).
Zone deactivation is useful when detectors are not working properly and you wish to avoid
false alarms. Under normal circumstances, bypassed (disabled) zones can still generate
tamper events. If you do not wish this to occur you must set the "Bypass Tamper" option on
the control panel.
A bypassed zone can be considered "Off".

Technical terminology and Glossary 77

 Installation and Programming Manual

Appendix B

SHORTCUTS AT DEFAULT
n. ICON description function parameter n. ICON DESCRIPTION function
ZoneBypass Accesses the User Menu
1 Arm/Disarm Applies a pre-set scenario Scenario 19
menu section: Activations/Zones

Immediately deactivates
the outputs relative to
Accesses the User Menu
2 Stop alarms zone/partition alarm and 20 Voice memo section: Voice functions
tamper events and system
tamper events.
Cancels the call queue and
3 Clear call queue stops ongoing calls (if 21 Output control Accesses the User Menu
section: Outputs ON/OFF
any).
Carries out a “Stop alarms”
operation and, at the same Accesses the User Menu
Enab.answerpho
4 Delete memory time, deletes memory of 22 ne section: Activations/
system and partition alarm Answerphone
and tamper events.
Accesses the User Menu
5 Activate outputs Activates one of the Output 23 Enab.teleservice section: Activations/
programmed outputs.
Teleservice

Deactivates one of the Accesses the User Menu

6 Deactiv. outputs programmed outputs. Output 24 Enable codes section: Activations/Codes

Delays auto-arming time of Accesses the User Menu

7 Overtime partitions by 30 minutes. 25 Enable keys section: Activations/Keys

Sends a call to the Installer Accesses the User Menu

8 Teleservice req. company number 26 Enable timers
(Teleservice number). section: Activations/Timers

Plays a recorded voice

message which announces Accesses the User Menu
9 Voice menu User code 27 Enab. auto-arm section: Activations/Auto-
the shortcuts assigned to arm
the number keys.
Allows eavesdropping
10 Listen-in over-the-phone by means Keypad 28 View events log Accesses the User Menu
of a microphone located on section: View/Events log
suitably placed keypad.
Accesses the User Menu
11 Intercom Call section: Voice functions/ 29 View alarm log Accesses the User Menu
section: View/Alarms log
Intercom Call

Arm/disarm Accesses the User Menu Accesses the User Menu

12 menu section: Arm/Disarm 30 View faults log section: View/Faults log

Accesses the User Menu

Accesses the User Menu
13 Alarm menu section: Manage alarms 31 View arm ops log section: View/Arm/Disarm
ops.

Voice func. Accesses the User Menu ViewSystemStatu Accesses the User Menu
14 32 section: View/System
menu section: Voice functions s Voltage

Activations Accesses the User Menu Accesses the User Menu

15 33 View zone status
menu section: Activations section: View/Zone status

Accesses the User Menu Accesses the User Menu

16 View menu 34 Change PIN
section: View section: Change PIN
Provides voice information
regarding the armed/ Accesses the User Menu
17 Arming status disarmed status of the 35 Time/Date section: Time/Date
partitions.

Keypad Accesses the User Menu Accesses the User Menu

18 sett.menu section:Keypad Keypad 36 View faults section: View/Faults

Accesses the User Menu

37 Thermostat
section:Thermostat

78 Shortcuts at default
Installation and Programming Manual

Appendix C

AVAILABLE ICONS

The following Table shows the icons provided at default. The icons can be
customized to suit the keypad shortcuts.

n. ICON description

38 Disarm

39 Instant mode

40 Stay Arm

41 Away mode

Timer control and key/code

4 lockout

43 Open Gate

44 Close Gate

45 Turn Off sprinkler

46 Turn On sprinkler

47 Telephone Menu

48 Heating

49 Empty Icon

50 Empty Icon

Available Icons 79
 Installation and Programming Manual

Appendix D

VOICE MESSAGES

The SmartLogos30M voice board provides 500 voice message slots, 291 of which
are pre-recorded at factory. The messages are arranged in such way as to
produce event-related voice calls which clearly describe the related event.
The following Table shows the message numbers and their purpose, together
with the respective recording time.

Message duration Message duration

(in seconds) (in seconds)
Type Number Default message Type Number Default message
High Average High Average
quality quality quality quality
Available 169 271 211 View menu 2.5 4
user- 1 – 100 ‘’ (for all 100 (for all 100 212 System status 2.5 4
messages messages) messages)
213 Keypad settings menu 2.5 4
None
101 - 165 ‘’ 214 Zone activations 2.5 4
available menu
166 Scenario 1 2.5 4 215 Voice memo 2.5 4
167 Scenario 2 2.5 4 Output management
168 Scenario 3 2.5 4 216 2.5 4
menu
169 Scenario 4 2.5 4 Enable/Disable
217 2.5 4
170 Scenario 5 2.5 4 answerphone
171 Scenario 6 2.5 4 218 Enable teleservice 2.5 4
172 Scenario 7 2.5 4 219 Enable codes 2.5 4
173 Scenario 8 2.5 4 Shortcuts 220 Enable keys 2.5 4
174 Scenario 9 2.5 4 221 Enable timers 2.5 4
175 Scenario 10 2.5 4 222 Enable auto-arming 2.5 4
176 Scenario 11 2.5 4 223 View events log 2.5 4
177 Scenario 12 2.5 4 224 View alarms log 2.5 4
178 Scenario 13 2.5 4 225 View faults log 2.5 4
179 Scenario 14 2.5 4 226 View arm/disarm 2.5 4
Arming 180 Scenario 15 2.5 4 operations
scenarios 181 Scenario 16 2.5 4 227 View battery status 2.5 4
182 Scenario 17 2.5 4 228 View zone status 2.5 4
183 Scenario 18 2.5 4 229 Change PIN 2.5 4
184 Scenario 19 2.5 4 230 Date/Time settings 2.5 4
185 Scenario 20 2.5 4 231 Faults list 2.5 4
186 Scenario 21 2.5 4 None
232 - 240 ‘’
187 Scenario 22 2.5 4 available
188 Scenario 23 2.5 4 241 Restoral 1.25 2
189 Scenario 24 2.5 4 242 To 0.63 1
190 Scenario 25 2.5 4 243 Press 1.25 2
191 Scenario 26 2.5 4 244 Location 6.25 10
192 Scenario 27 2.5 4 245 Zero 2.5 4
193 Scenario 28 2.5 4 246 One 2.5 4
194 Scenario 29 2.5 4 Generic 247 Two 2.5 4
195 Scenario 30 2.5 4 messages 248 Three 2.5 4
196 Armed in Away mode 2.5 4 249 Four 2.5 4
197 Stop alarm 2.5 4 250 Five 2.5 4
198 Stop call queue 2.5 4 251 Six 2.5 4
199 Delete memory 2.5 4 252 Seven 2.5 4
200 Activate output 2.5 4 253 Eight 2.5 4
201 Deactivate output 2.5 4 254 Nine 2.5 4
202 Overtime request 2.5 4 255 Away mode 3.13 5
203 Request maintenance 2.5 4 Partition 256 Armed in Stay mode 3.13 5
Shortcuts 204 StartVoiceNotifier 2.5 4 status 257 Instant mode 3.13 5
205 Listen-in 2.5 4 258 Disarm 3.13 5
206 Intercom Call 2.5 4
Access arm/disarm
207 menu 2.5 4

208 Access manage 2.5 4

alarms menu
209 Voice menu 2.5 4
210 Activations menu 2.5 4

80 Voice messages
Installation and Programming Manual

Message duration Message duration

(in seconds) (in seconds)
Type Number Default message Type Number Default message
High Average High Average
quality quality quality quality
To go back to 331 Zone 61 3.13 5
Menu 259 3.13 5
previous menu press 332 Zone 62 3.13 5
Activation / 260 To activate 1.88 3 333 Zone 63 3.13 5
Deactivation 261 To deactivate 1.88 3 334 Zone 64 3.13 5
Type-in user- Type-in user-code 335 Zone 65 3.13 5
code PIN 262 PIN followed by # 2.5 4
336 Zone 66 3.13 5
263 Relay 2.5 4 337 Zone 67 3.13 5
Outputs 264 Output 1 2.5 4 338 Zone 68 3.13 5
265 Output 2 2.5 4 339 Zone 69 3.13 5
None 340 Zone 70 3.13 5
266 - 270 ‘’
available 341 Zone 71 3.13 5
271 Zone 1 3.13 5 342 Zone 72 3.13 5
272 Zone 2 3.13 5 343 Zone 73 3.13 5
273 Zone 3 3.13 5 344 Zone 74 3.13 5
274 Zone 4 3.13 5 345 Zone 75 3.13 5
275 Zone 5 3.13 5 346 Zone 76 3.13 5
276 Zone 6 3.13 5 347 Zone 77 3.13 5
277 Zone 7 3.13 5 348 Zone 78 3.13 5
278 Zone 8 3.13 5 349 Zone 79 3.13 5
279 Zone 9 3.13 5 Zone 350 Zone 80 3.13 5
280 Zone 10 3.13 5 Terminal 351 Zone 81 3.13 5
281 Zone 11 3.13 5 352 Zone 82 3.13 5
282 Zone 12 3.13 5 353 Zone 83 3.13 5
283 Zone 13 3.13 5 354 Zone 84 3.13 5
284 Zone 14 3.13 5 355 Zone 85 3.13 5
285 Zone 15 3.13 5 356 Zone 86 3.13 5
286 Zone 16 3.13 5 357 Zone 87 3.13 5
287 Zone 17 3.13 5 358 Zone 88 3.13 5
288 Zone 18 3.13 5 359 Zone 89 3.13 5
289 Zone 19 3.13 5 360 Zone 90 3.13 5
290 Zone 20 3.13 5 361 Zone 91 3.13 5
291 Zone 21 3.13 5 362 Zone 92 3.13 5
292 Zone 22 3.13 5 363 Zone 93 3.13 5
293 Zone 23 3.13 5 364 Zone 94 3.13 5
294 Zone 24 3.13 5 365 Zone 95 3.13 5
295 Zone 25 3.13 5 366 Zone 96 3.13 5
296 Zone 26 3.13 5 367 Zone 97 3.13 5
297 Zone 27 3.13 5 368 Zone 98 3.13 5
298 Zone 28 3.13 5 369 Zone 99 3.13 5
299 Zone 29 3.13 5 370 Zone 100 3.13 5
Zone 300 Zone 30 3.13 5 371 Partition 1 3.13 5
Terminal 301 Zone 31 3.13 5 372 Partition 2 3.13 5
302 Zone 32 3.13 5 373 Partition 3 3.13 5
303 Zone 33 3.13 5 374 Partition 4 3.13 5
304 Zone 34 3.13 5 375 Partition 5 3.13 5
305 Zone 35 3.13 5 376 Partition 6 3.13 5
306 Zone 36 3.13 5 377 Partition 7 3.13 5
307 Zone 37 3.13 5 Partition 378 Partition 8 3.13 5
308 Zone 38 3.13 5 379 Partition 9 3.13 5
309 Zone 39 3.13 5 380 Partition 10 3.13 5
310 Zone 40 3.13 5 381 Partition 11 3.13 5
311 Zone 41 3.13 5 382 Partition 12 3.13 5
312 Zone 42 3.13 5 383 Partition 13 3.13 5
313 Zone 43 3.13 5 384 Partition 14 3.13 5
314 Zone 44 3.13 5 385 Partition 15 3.13 5
315 Zone 45 3.13 5 386 Code 1 2.5 4
316 Zone 46 3.13 5 387 Code 2 2.5 4
317 Zone 47 3.13 5 388 Code 3 2.5 4
318 Zone 48 3.13 5 389 Code 4 2.5 4
319 Zone 49 3.13 5 390 Code 5 2.5 4
320 Zone 50 3.13 5 Codes
391 Code 6 2.5 4
321 Zone 51 3.13 5 392 Code 7 2.5 4
322 Zone 52 3.13 5 393 Code 8 2.5 4
323 Zone 53 3.13 5 394 Code 9 2.5 4
324 Zone 54 3.13 5 395 Code 10 2.5 4
325 Zone 55 3.13 5
326 Zone 56 3.13 5
327 Zone 57 3.13 5
328 Zone 58 3.13 5
329 Zone 59 3.13 5
330 Zone 60 3.13 5

Voice messages 81
 Installation and Programming Manual

Message duration Message duration

(in seconds) (in seconds)
Type Number Default message Type Number Default message
High Average High Average
quality quality quality quality
396 Key 1 2.5 4 451 Emergency 2.5 4
397 Key 2 2.5 4 452 Open-panel tamper 2.5 4
398 Key 3 2.5 4 Dislodged-panel
453 2.5 4
399 Key 4 2.5 4 tamper
400 Key 5 2.5 4 454 Zone fuse fault 2.5 4
Keys 455 I-BUS fuse fault 2.5 4
401 Key 6 2.5 4
402 Key 7 2.5 4 456 Battery fault 2.5 4
403 Key 8 2.5 4 457 Mains failure 2.5 4
404 Key 9 2.5 4 458 Expansion tamper 2.5 4
405 Key 10 2.5 4 459 Keypad Tamper 2.5 4
406 Keypad 1 2.5 4 460 Reader Tamper 2.5 4
407 Keypad 2 2.5 4 461 Expansion Loss 2.5 4
Keypads 408 Keypad 3 2.5 4 462 Keypad Loss 2.5 4
409 Keypad 4 2.5 4 463 Reader Loss 2.5 4
410 Keypad 5 2.5 4 Event type 464 Jamming 2.5 4
411 Reader 1 2.5 4 Low battery wireless
465 zone 2.5 4
412 Reader 2 2.5 4
Readers 413 Reader 3 2.5 4 466 Wireless zone loss 2.5 4
414 Reader 4 2.5 4 467 Valid Installer code 2.5 4
415 Reader 5 2.5 4 468 Invalid code 2.5 4
Function 416 Fire 2.5 4 469 False key 2.5 4
keys 417 Ambulance 2.5 4 470 Telephone line down 2.5 4
Emergency 418 Police 2.5 4 471 Periodic test event 2.5 4
None 472 Hard reset 2.5 4
419 – 425 ‘’ 473 Call queue full 2.5 4
available
426 Zone alarm 2.5 4 474 Successful call 2.5 4
427 Terminal tamper 2.5 4 475 Initialize 2.5 4
programming
428 Partition alarm 2.5 4
476 Ongoing call 2.5 4
429 Stay alarm 2.5 4
477 Output fault 2.5 4
430 Partition tamper 2.5 4
None
431 Zone bypass 2.5 4 478 – 485 ‘’
available
Partition not-ready-
432 to-arm 2.5 4 37.5 60
Voice memo 486 – 500 ‘’ (for all 15 (for all 15
433 Away arm request 2.5 4 slots
messages) messages)
434 Stay arm request 2.5 4
435 Armed in Away mode 2.5 4
436 Armed in Stay mode 2.5 4
437 Reset partition 2.5 4
Partition armed,
438 2.5 4
Event type leave partition
439 Disarm partition 2.5 4
440 Pre-arm alert 2.5 4
441 Overtime request 2.5 4
442 Welcome 2.5 4
443 Valid user-code 2.5 4
444 Valid key 2.5 4
Valid user-code at
445 keypad 2.5 4
446 Valid key at reader 2.5 4
Valid user-code on
447 partition 2.5 4
448 Valid key on partition 2.5 4
449 Failed call 2.5 4
450 Timer event 2.5 4

82 Voice messages
Installation and Programming Manual

Appendix E

SCREW TERMINALS

All the terminals on the SmartLiving control panel and its peripherals (expansions
and keypads) are identified by distinctive numbers transcribed in the “CCC”
programming field of the “CONTACT-ID” protocol, in order to allow the precise
localization of events related to zones or terminals.
In the case of double zones, the second zone will be identified by the number
“500 + n.” (where “n.” stands for the number of the terminal).

terminal terminal terminal terminal

n. location n. location n. location n. location n. terminal location

1 Panel T1 51 Exp. 9 T1 101 Exp. 19 T1 151 Exp. 29 T1 201 Exp. 39 T1

2 Panel T2 52 Exp. 9 T2 102 Exp. 19 T2 152 Exp. 29 T2 202 Exp. 39 T2
3 Panel T3 53 Exp. 9 T3 103 Exp. 19 T3 153 Exp. 29 T3 203 Exp. 39 T3
4 Panel T4 54 Exp. 9 T4 104 Exp. 19 T4 154 Exp. 29 T4 204 Exp. 39 T4
5 Panel T5 55 Exp. 9 T5 105 Exp. 19 T5 155 Exp. 29 T5 205 Exp. 39 T5
6 Panel T6 56 Exp. 10 T1 106 Exp. 20 T1 156 Exp. 30 T1 206 Exp. 40 T1
7 Panel T7 57 Exp. 10 T2 107 Exp. 20 T2 157 Exp. 30 T2 207 Exp. 40 T2
8 Panel T8 58 Exp. 10 T3 108 Exp. 20 T3 158 Exp. 30 T3 208 Exp. 40 T3
9 Panel T9 59 Exp. 10 T4 109 Exp. 20 T4 159 Exp. 30 T4 209 Exp. 40 T4
10 Panel T10 60 Exp. 10 T5 110 Exp. 20 T5 160 Exp. 30 T5 210 Exp. 40 T5
11 Exp. 1 T1 61 Exp. 11 T1 111 Exp. 21 T1 161 Exp. 31 T1 211 Keyp. 1 T1
12 Exp. 1 T2 62 Exp. 11 T2 112 Exp. 21 T2 162 Exp. 31 T2 212 Keyp. 1 T2
13 Exp. 1 T3 63 Exp. 11 T3 113 Exp. 21 T3 163 Exp. 31 T3 213 Keyp. 2 T1
14 Exp. 1 T4 64 Exp. 11 T4 114 Exp. 21 T4 164 Exp. 31 T4 214 Keyp. 2 T2
15 Exp. 1 T5 65 Exp. 11 T5 115 Exp. 21 T5 165 Exp. 31 T5 215 Keyp. 3 T1
16 Exp. 2 T1 66 Exp. 12 T1 116 Exp. 22 T1 166 Exp. 32 T1 216 Keyp. 3 T2
17 Exp. 2 T2 67 Exp. 12 T2 117 Exp. 22 T2 167 Exp. 32 T2 217 Keyp. 4 T1
18 Exp. 2 T3 68 Exp. 12 T3 118 Exp. 22 T3 168 Exp. 32 T3 218 Keyp. 4 T2
19 Exp. 2 T4 69 Exp. 12 T4 119 Exp. 22 T4 169 Exp. 32 T4 219 Keyp. 5 T1
20 Exp. 2 T5 70 Exp. 12 T5 120 Exp. 22 T5 170 Exp. 32 T5 220 Keyp. 5 T2
21 Exp. 3 T1 71 Exp. 13 T1 121 Exp. 23 T1 171 Exp. 33 T1 221 Keyp. 6 T1
22 Exp. 3 T2 72 Exp. 13 T2 122 Exp. 23 T2 172 Exp. 33 T2 222 Keyp. 6 T2
23 Exp. 3 T3 73 Exp. 13 T3 123 Exp. 23 T3 173 Exp. 33 T3 223 Keyp. 7 T1
24 Exp. 3 T4 74 Exp. 13 T4 124 Exp. 23 T4 174 Exp. 33 T4 224 Keyp. 7 T2
25 Exp. 3 T5 75 Exp. 13 T5 125 Exp. 23 T5 175 Exp. 33 T5 225 Keyp. 8 T1
26 Exp. 4 T1 76 Exp. 14 T1 126 Exp. 24 T1 176 Exp. 34 T1 226 Keyp. 8 T2
27 Exp. 4 T2 77 Exp. 14 T2 127 Exp. 24 T2 177 Exp. 34 T2 227 Keyp. 9 T1
28 Exp. 4 T3 78 Exp. 14 T3 128 Exp. 24 T3 178 Exp. 34 T3 228 Keyp. 9 T2
29 Exp. 4 T4 79 Exp. 14 T4 129 Exp. 24 T4 179 Exp. 34 T4 229 Keyp. 10 T1
30 Exp. 4 T5 80 Exp. 14 T5 130 Exp. 24 T5 180 Exp. 34 T5 230 Keyp. 10 T2
31 Exp. 5 T1 81 Exp. 15 T1 131 Exp. 25 T1 181 Exp. 35 T1 231 Keyp. 11 T1
32 Exp. 5 T2 82 Exp. 15 T2 132 Exp. 25 T2 182 Exp. 35 T2 232 Keyp. 11 T2
33 Exp. 5 T3 83 Exp. 15 T3 133 Exp. 25 T3 183 Exp. 35 T3 233 Keyp. 12 T1
34 Exp. 5 T4 84 Exp. 15 T4 134 Exp. 25 T4 184 Exp. 35 T4 234 Keyp. 12 T2
35 Exp. 5 T5 85 Exp. 15 T5 135 Exp. 25 T5 185 Exp. 35 T5 235 Keyp. 13 T1
36 Exp. 6 T1 86 Exp. 16 T1 136 Exp. 26 T1 186 Exp. 36 T1 236 Keyp. 13 T2
37 Exp. 6 T2 87 Exp. 16 T2 137 Exp. 26 T2 187 Exp. 36 T2 237 Keyp. 14 T1
38 Exp. 6 T3 88 Exp. 16 T3 138 Exp. 26 T3 188 Exp. 36 T3 238 Keyp. 14 T2
39 Exp. 6 T4 89 Exp. 16 T4 139 Exp. 26 T4 189 Exp. 36 T4 239 Keyp. 15 T1
40 Exp. 6 T5 90 Exp. 16 T5 140 Exp. 26 T5 190 Exp. 36 T5 240 Keyp. 15 T2
41 Exp. 7 T1 91 Exp. 17 T1 141 Exp. 27 T1 191 Exp. 37 T1
4 Exp. 7 T2 92 Exp. 17 T2 142 Exp. 27 T2 192 Exp. 37 T2
43 Exp. 7 T3 93 Exp. 17 T3 143 Exp. 27 T3 193 Exp. 37 T3
44 Exp. 7 T4 94 Exp. 17 T4 144 Exp. 27 T4 194 Exp. 37 T4
45 Exp. 7 T5 95 Exp. 17 T5 145 Exp. 27 T5 195 Exp. 37 T5
46 Exp. 8 T1 96 Exp. 18 T1 146 Exp. 28 T1 196 Exp. 38 T1
47 Exp. 8 T2 97 Exp. 18 T2 147 Exp. 28 T2 197 Exp. 38 T2
48 Exp. 8 T3 98 Exp. 18 T3 148 Exp. 28 T3 198 Exp. 38 T3
49 Exp. 8 T4 99 Exp. 18 T4 149 Exp. 28 T4 199 Exp. 38 T4
50 Exp. 8 T5 100 Exp. 18 T5 150 Exp. 28 T5 200 Exp. 38 T5

Screw Terminals 83
 Installation and Programming Manual

Appendix F

COMBINATION OF OUTPUTS
TRIGGERED BY EVENTS

This appendix shows the event-generated actions (activations/deactivations) of

the outputs programmed in the “Outputs” and “Other outputs” sections combined
with the “SirenSound types” of the sounderflashers on the BUS.

Table 37: Output typology

Symbol/Initials Description
TM Output on terminal/Relay/OC1/OC2 - monostable
TB Output on terminal/Relay/OC1/OC2 - bistable
SM Sounderflasher output with limited flasher time
SB Sounderflasher output with unlimited flasher time

Table 38: Functioning and deactivation of the outputs

Symbol/Initials Description
These outputs will deactivate if a Stop alarm, Reset partition or Disarm
A operation is carried out while the monostable time of the main output is
running.
These outputs will deactivate only when the event clears after expiry of the
B monostable time of the main output.
These outputs, due to the continuous flasher function, will not deactivate
automatically.
C In order to deactivate the SB flashers of the sounderflasher after expiry of the
monostable time applied to the main output, you must:
• trigger an event which applies a Stop pattern to the SB flashers
• reset the partition
D These outputs will deactivate only when the event clears.
These outputs will deactivate if, when an event is active, a Stop alarm
E operation, reset or disarm partition command operation is carried out.
These outputs, due to the continuous flasher function, will not deactivate
automatically. In order to deactivate the SB flashers of the device on
F termination of the event, you must:
• trigger an event which applies a Stop pattern to the SB flashers
• reset the partition
G These outputs will deactivate when the respective monostable time expires

Table 39: Output combinations

Principal output Other outputs
Event groups
TM TB SM SB TM TB SM SB
Zone alarm
AG AG AB AG AC
Terminal tamper DE EG DG EG F
Partition alarm AG AG AB AG AC
Partition tamper
F EG DG EG F
Control panel open
Dislodged panel
AG AG AD AG AC
Expansion tamper/loss
Keypad tamper/loss DE EG DG EG C
Reader tamper/loss
Sounderflasher tamper/loss AG AG AB AG AC
Jamming
Wireless zone loss
F EG DG EG C
Telephone line down
G G B G C
D G D G F
other events
G G B G C
F G C G C

84 Combination of outputs triggered by events

Installation and Programming Manual

Appendix G

COMPLIANCY

In order to guarantee CEI 79-2 compliancy, you must adhere to the following
guidelines:
• nBy/X readers must be equipped with devices which protect them against the
forced-opening and dislodgement of their casings from their locations, in
compliance with Level 2, as indicated in paragraph 3-2-5 Installing nBy/S
readers.
• JOY, nCode and Concept keypads must be equipped with enabled tamper-
protection devices, as indicated in paragraph 3-3-1 Addressing the keypads.
• FLEX5/U expansion boards must be either mounted inside the metal enclosure
of the 1050L or 10100L control panel, or equipped with devices which protect
them against the forced-opening of their casings and dislodgement from their
locations, in compliance with Performance level 2.
• The lines relating to the intrusion-detection zones must be configured as
'Double balancing' with double EOL resistors, or as Single balancing with
single EOL resistor. They must also be equipped with devices which protect
them against the forced-opening of their casings.
• Terminal tamper, peripheral tamper and control-panel tamper events must
trigger audible signals (sounder signals) for a period of not less than 3
minutes.
In order to guarantee EN50131 compliancy of devices, you must adhere to the
following guidelines:
• Adhere to the previously mentioned guidelines relating to CEI 79-2
compliancy.
• In the “Panel options” section enable:
•• Keypad lockout
•• OpenZonesArmLock
•• NoUserTamp.reset
•• 50131ReaderLedOFF
•• 50131StatHidden
•• 50131IconsHidden
• In the section “Other parameters - FaultForNotReady”, enable the following
options:
•• Zone fuse fault
•• IBUS fuse fault
•• Low battery
•• Mains failure
•• Tel. line down
•• Jamming
•• Low battery WLS
•• WLS zone loss
•• LossTamp.ongoing

Compliancy 85
 Installation and Programming Manual

Appendix H

ORDER CODES

Please quote the following order codes when ordering items from the INIM
Electronics product range:
Access Codes Product description
Air2-BS100 Wireless transceiver
Air2-IRF100 Wireless PIR with 12m coverage
Air2-KF100 4 button remote-control keyfob
Air2-MC100 Wireless magnetic contact with 2 inputs/outputs
AUXREL32 Power distribution relay-board for SmartLiving 1050L and 10100L
Concept/G Touch keypad with backlit graphic display and keys equipped with input/output terminal
DCMIINE0SLIVINGE SmartLiving Installation and Programming Manual
DCMUINE0SLIVINGE SmartLiving User's Manual
Flex5/P Two-way Input/Output expansion board in tamper-protected plastic enclosure
Flex5/U Two-way Input/Output expansion board transparent plastic enclosure with terminal on view
IB100/A BUS isolator with data and power regeneration and tamper protection
IB100/RP BUS isolator with data regeneration and tamper protection
IB100/RU BUS isolator with data regeneration and on-view terminals
Ivy Self-powered sounderflasher - suitable for outdoor installation
Ivy-B Self-powered sounderflasher with BUS connection capacity - suitable for outdoor installation
Ivy-BF Self-powered sounderflasher with BUS connection capacity and foam-tamper protection - suitable for outdoor installation
Ivy-BFM Self-powered sounderflasher with BUS connection capacity and foam-tamper in metal-look (chrome) enclosure - suitable
for outdoor installation
Ivy-BM Self-powered sounderflasher with BUS connection capacity in metal-look (chrome) enclosure - suitable for outdoor
installation
Ivy-F Self-powered sounderflasher with foam-tamper protection - suitable for outdoor installation
Ivy-FM Self-powered sounderflasher with foam-tamper protection in metal-look (chrome) enclosure - suitable for outdoor
installation
Ivy-M Self-powered sounderflasher in metal-look (chrome) enclosure - suitable for outdoor installation
Joy/GR Keypad with backlit graphic display with two input/output terminals
Joy/MAX Keypad with backlit graphic display with two input/output terminals and built-in proximity reader, microphone, speaker
and temperature sensor
LINK232F9F9 RS232 cable link to PC and/or INIM devices
LINKUSABAB USB cable link to PC and/or INIM devices
LINKIBUS Temporary cable link for I-BUS
nBy/S Wall-mount proximity reader
nBy/X Flush-mount proximity reader
nCard Card for nBy proximity readers
nCode/G Keypad with backlit graphic display with one input/output terminal
nKey Tag for nBy proximity readers
ProbeTH Thermal probe for battery-charge optimization
SmartLAN/G Ethernet interface for programming and internet operations using TCP-IP and UDP protocols
SmartLAN/SI Ethernet interface for programming via internet using TCP-IP and UDP protocols
SmartLeague Programming and management software for INIM devices
SmartLink/GWB SmartLink/G Kit for SmartLiving 1050L and 10100L
SmartLiving 505 Intrusion control panel: manages 5 terminals, 5 partitions, switching power supply @ 1.2A, comes in metal enclosure with
DCMIINE0SLIVINGE-R300-20100601

housing for 1 battery @7Ah

SmartLiving515 Intrusion control panel: manages 5 to 10 terminals, 5 partitions, switching power supply @ 1.2A, comes in metal
enclosure with housing for 1 battery @7Ah
SmartLiving 1050 Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power supply @3A, comes in metal
enclosure with housing for 1 battery @7Ah
SmartLiving1050L Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power supply @3A, comes in metal
enclosure with housing for 1 battery @17Ah
SmartLiving10100L Intrusion control panel: manages 10 to 100 terminals, 15 partitions, switching power supply @5A, optional TCP/IP
connectivity, comes in metal enclosure with housing for 1 battery @17Ah
SmartLogos30M Voice board (for SmartLiving)
SmartLook SmartLook is a centralized-control software program for INIM's fire detection and intrusion control systems
SmartModem100 Remote programming modem
SPS12040 Switching power supply/battery charger in enclosure - 3A, 12V
SPS12100 Switching power supply/battery charger in enclosure - 5A, 12V
TamperNO Dislodgement-tamper device for SmartLiving control panels

86 Order Codes
Installation and Programming Manual

Notes

87
ISOAzienda
9001:200 Registered
certificata company
ISO 9001 : 2008

via Fosso Antico

Loc. Centobuchi
63033 Monteprandone
(AP) ITALY

Tel. +39 0735 705007

Fax +39 0735 704912

info@inim.biz
www.inim.biz