Internal Use Only

North/Latin America [Link]

Europe/Africa [Link]
Asia/Oceania [Link]

LED LCD TV
SERVICE MANUAL
CHASSIS : LB12B

MODEL : 42LV3710/371Y/3730
MODEL : 42LV3710/371Y-TB 42LV3730-TD
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL67007018 (1103-REV00) Printed in Korea

 CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ................................................................................. 3

SPECIFICATION ....................................................................................... 4

ADJUSTMENT INSTRUCTION ................................................................ 7

EXPLODED VIEW .................................................................................. 14

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Copyright © 2011 LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
 SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5 mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1 W), keep the resistor 10 mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer, AC Volt-meter

always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical Good Earth Ground
shock. such as WATER PIPE,
To Instrument's CONDUIT etc.
0.15 uF
Leakage Current Cold Check(Antenna Cold Check) exposed
With the instrument AC plug removed from AC source, connect an METALLIC PARTS
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC 1.5 Kohm/10W
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc. When 25A is impressed between Earth and 2nd Ground
If the exposed metallic part has a return path to the chassis, the for 1 second, Resistance must be less than 0.1 Ω
measured resistance should be between 1 MΩ and 5.2 MΩ.
*Base on Adjustment standard
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Copyright © 2011 LG Electronics. Inc. All rights reserved. -3- LGE Internal Use Only
Only for training and service purposes
 SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range 3. Test method

This specification is applied to the LCD TV used LB12B 1) Performance: LGE TV test method followed
chassis. 2) Demanded other specification
- Safety : CE, IEC specification
2. Requirement for Test - EMC : CE, IEC
Each part is tested as below without special appointment.

1) Temperature: 25 ºC ± 5 ºC(77 ºF ± 9 ºF), CST: 40 ºC ± 5 ºC

2) Relative Humidity : 65 % ± 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.

4. Model General Specification

No. Item Specification Remarks
1. Market ASIA, Oceania, Africa, DTV & Analog
Middle East(PAL/DVB Market) * DTV Region : Australia/New Zealand(AU), Singapore(SG), Indonesia(ID),
Malaysia(MY), Vietnam(VN), South Africa(ZA), Iran(IR)
2. Broadcasting system 1) PAL-B/G * Australia/India : only PAL
2) PAL-D/K
3) PAL-I/I’
3) SECAM-DK, BG, I
4) DVB-T
3. Receiving system Analog : Upper Heterodyne G DVB-T
Digital : COFDM, QAM - Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
4. Video Input RCA (2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60
Rear 1EA, AV gender jack 1EA
5. Head phone out Antena, AV1, AV3, Component1,
Component2, RGB, HDMI1, HDMI2,
HDMI3, HDMI4, USB1, USB2
6. Component Input (2EA) Y/Cb/Cr, Y/Pb/Pr Rear 1EA, Gender 1EA
7. RGB Input (1EA) RGB-PC Analog(D-SUB 15PIN)
8. HDMI Input (4EA) HDMI1-ARC PC(HDMI version 1.3) Support HDCP
HDMI2
HDMI3
HDMI4
9. Audio Input (5EA) RGB/DVI Audio L/R Input
Component1,2
AV1,2
10. SDPIF out (1EA) SPDIF out
11. USB (2EA) EMF, DivX HD, For SVC(download) JPEG, MP3, DivX HD Plus

Copyright © 2011 LG Electronics. Inc. All rights reserved. -4- LGE Internal Use Only
Only for training and service purposes
5. Component Video Input (Y, CB/PB, CR/PR)
Specification
No. Remark
Resolution H-freq(kHz) V-freq(Hz)
1. 720x480 15.73 60.00 SDTV,DVD 480i
2. 720x480 15.63 59.94 SDTV,DVD 480i
3. 720x480 31.47 59.94 480p
4. 720x480 31.50 60.00 480p
5. 720x576 15.625 50.00 SDTV,DVD 625 Line
6. 720x576 31.25 50.00 HDTV 576p
7. 1280x720 45.00 50.00 HDTV 720p
8. 1280x720 44.96 59.94 HDTV 720p
9. 1280x720 45.00 60.00 HDTV 720p
10. 1920x1080 31.25 50.00 HDTV 1080i
11. 1920x1080 33.75 60.00 HDTV 1080i
12. 1920x1080 33.72 59.94 HDTV 1080i
13. 1920x1080 56.250 50 HDTV 1080p
14. 1920x1080 67.5 60 HDTV 1080p

6. RGB (PC)
Specification
No. Proposed Remarks
Resolution H-freq(kHz) V-freq(Hz) Pixel Clock(MHz)
1. 720*400 31.468 70.08 28.321 For only DOS mode
2. 640*480 31.469 59.94 25.17 VESA Input 848*480 60 Hz, 852*480 60 Hz
-> 640*480 60 Hz Display
3. 800*600 37.879 60.31 40.00 VESA
4. 1024*768 48.363 60.00 65.00 VESA(XGA)
5. 1360*768 47.72 59.8 84.75 WXGA
6. 1920*1080 66.587 59.93 138.625 WUXGA FHD model

Copyright © 2011 LG Electronics. Inc. All rights reserved. -5- LGE Internal Use Only
Only for training and service purposes
7. HDMI Input
(1) DTV Mode
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
1. 720*480 31.469 /31.5 59.94 /60 27.00/27.03 SDTV 480P
2. 720*576 31.25 50 54 SDTV 576P
3. 1280*720 37.500 50 74.25 HDTV 720P
4. 1280*720 44.96 /45 59.94 /60 74.17/74.25 HDTV 720P
5. 1920*1080 33.72 /33.75 59.94 /60 74.17/74.25 HDTV 1080I
6. 1920*1080 28.125 50.00 74.25 HDTV 1080I
7. 1920*1080 26.97 /27 23.97 /24 74.17/74.25 HDTV 1080P
8. 1920*1080 33.716 /33.75 29.976 /30.00 74.25 HDTV 1080P
9. 1920*1080 56.250 50 148.5 HDTV 1080P
10. 1920*1080 67.43 /67.5 59.94 /60 148.35/148.50 HDTV 1080P

(2) PC Mode
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
1. 720*400 31.468 70.08 28.321 HDCP
2. 640*480 31.469 59.94 25.17 VESA HDCP
3. 800*600 37.879 60.31 40.00 VESA HDCP
4. 1024*768 48.363 60.00 65.00 VESA(XGA) HDCP
5. 1360*768 47.72 59.8 84.75 WXGA HDCP
6. 1920*1080 67.5 60.00 138.625 WUXGA HDCP/FHD model

Copyright © 2011 LG Electronics. Inc. All rights reserved. -6- LGE Internal Use Only
Only for training and service purposes
 ADJUSTMENT INSTRUCTION
1. Application Range (3) Adjustment
1) Adjustment method
This specification sheet is applied to all of the LED LCD TV - Using RS-232, adjust items in the other shown in
with LB12B chassis. “3.1.(3).3)”

2) Adj. protocol
2. Designation Protocol Command Set ACK
1) Because this is not a hot chassis, it is not necessary to use Enter adj. mode aa 00 00 a 00 OK00x
an isolation transformer. However, the use of isolation
Source change xb 00 40 b 00 OK40x (Adjust 480i, 1080p Comp1 )
transformer will help protect test instrument.
xb 00 60 b 00 OK60x (Adjust 1920*1080 RGB)
2) Adjustment must be done in the correct order.
3) The adjustment must be performed in the circumstance of Begin adj. ad 00 10
25 ºC ± 5 ºC of temperature and 65 % ± 10 % of relative Return adj. result OKx (Case of Success)
humidity if there is no specific designation. NGx (Case of Fail)
4) The input voltage of the receiver must keep AC 100-240 Read adj. data (main) (main)
V~, 50/60 Hz.
ad 00 20 000000000000000000000000007c007b006dx
5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over (sub) (Sub)
15. ad 00 21 000000070000000000000000007c00830077x
Confirm adj. ad 00 99 NG 03 00x (Fail)
In case of keeping module is in the circumstance of 0 °C, it NG 03 01x (Fail)
should be placed in the circumstance of above 15 °C for 2 NG 03 02x (Fail)
hours.
OK 03 03x (Success)

In case of keeping module is in the circumstance of below - End adj. aa 00 90 a 00 OK90x

20 °C, it should be placed in the circumstance of above 15
°C for 3 hours. Ref.) ADC Adj. RS232C Protocol_Ver1.0

[Caution] 3) Adj. order

When still image is displayed for a period of 20 minutes or - aa 00 00 [Enter ADC adj. mode]
longer (especially where W/B scale is strong. Digital pattern - xb 00 04 [Change input source to Component1 (480i&
13ch and/or Cross hatch pattern 09ch), there can some 1080p)]
afterimage in the black level area. - ad 00 10 [Adjust 480i&1080p Comp1]
- xb 00 06 [Change input source to RGB(1024*768)]
- ad 00 10 [Adjust 1920*1080 RGB]
- ad 00 90 End adj.
3. Automatic Adjustment
3.1. ADC Adjustment 3.2. MAC Address
(1) Overview (1) Equipment & Condition
ADC adjustment is needed to find the optimum black level - Play file: [Link]
and gain in Analog-to-Digital device and to compensate - MAC Address edit
RGB deviation. - Input Start / End MAC address

(2) Equipment & Condition (2) Download method

1) Jig (RS-232C protocol) 1) Communication Prot connection
2) MSPG-925 Series Pattern Generator(MSPG-925FA,
pattern - 65) PCBA PC(RS-232C)
- Resolution : 480i Comp1
1080P Comp1
1920*1080 RGB
- Pattern : Horizontal 100% Color Bar Pattern RS-232C Po rt
- Pattern level : 0.7±0.1 Vp-p
- Image
Connect: PCBA Jig-> RS-232C Port== PC-> RS-232C Port

Copyright © 2011 LG Electronics. Inc. All rights reserved. -7- LGE Internal Use Only
Only for training and service purposes
 2) MAC Address Download, Whidevine Download 3.4. LAN PORT INSPECTION(PING TEST)
- Com 1,2,3,4 and 115200(Baud rate) Connect SET -> LAN port == PC -> LAN Port
SET PC
(1) Equipment setting
1) Play the LAN Port Test PROGRAM.
2) Input IP set up for an inspection to Test Program.
*IP Number : [Link]

(2) LAN PORT inspection (PING TEST)

1) Play the LAN Port Test Program.
2) Connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) Remove LAN CABLE

3.3. LAN
(1) Equipment & Condition
A Each other connection to LAN Port of IP Hub and Jig

(2) LAN inspection solution

A LAN Port connection with PCB
A Network setting at MENU Mode of TV
A Setting automatic IP
A Setting state confirmation
-> If automatic setting is finished, you confirm IP and
MAC Address. 3.5. Model name & Serial number Download
(1) Model name & Serial number D/L
A Press “Power on” key of service remote control.
(Baud rate : 115200 bps)
A Connect RS232 Signal Cable to RS-232 Jack.
A Write Serial number by use RS-232.
A Must check the serial number at Instart menu.

(2) Method & notice

A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
Technology Group.
[Link] number D/L must be conformed when it is
(3) WIDEVINE key Inspection produced in production line, because serial number D/L
- Confirm key input data at the “IN START” MENU Mode. is mandatory by D-book 4.0

Copyright © 2011 LG Electronics. Inc. All rights reserved. -8- LGE Internal Use Only
Only for training and service purposes
 * Manual Download (Model Name and Serial Number) 4. Manual Adjustment
If the TV set is downloaded by OTA or service man, sometimes
model name or serial number is initialized.(Not always) 4.1. ADC Adjustment
It is impossible to download by bar code scan, so It need 4.1.1. Overview
Manual download. ADC adjustment is needed to find the optimum black level and
a. Press the ‘instart’ key of ADJ remote control. gain in Analog-to-Digital device and to compensate RGB
b. Go to the menu ‘[Link] Number D/L’ like below photo. deviation.
c. Input the Factory model name(ex 42LD450-TA) or Serial
number like photo. 4.1.2. Equipment & Condition
(1) Adjust Remote control
(2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator
- Resolution :
480i,720*480(MSPG-925FA -> Model: 209, Pattern: 65) -
480i
1080p, 1920*1080(MSPG-925FA -> Model: 225, Pattern:
65) - 1080p
- Pattern : Horizontal 100 % Color Bar Pattern
- Pattern level: 0.7 ± 0.1 Vp-p
- Image
d. Check the model name Instart menu -> Factory name
displayed (ex 42LE7500-TA)
e. Check the Diagnostics(DTV country only) -> Buyer model
displayed (ex 42LE7500-TA)

3.6. WIFI MAC ADDRESS CHECK

a. Using RS232
H-freq(kHz) V-freq.(Hz)
Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG] (3) Must use standard cable
b. Check the menu on in-start
4.1.3. Adjust method
(1) ADC 480i, 1080p Comp1
1) Check connected condition of Component 1 cable to the
equipment.
2) Give a 480i, 1080p Mode, Horizontal 100% Color Bar
Pattern to Component 1.
(MSPG-925FA -> Model: 209, Pattern: 65) - 480i
(MSPG-925FA -> Model: 225, Pattern: 65) - 1080p
3) Change input mode as Component1 and picture mode
as “Standard”
4) Press the In-start Key on the ADJ remote control after at
least 1 min of signal reception. Then, select 7. External
ADC -> 1. COMP 1080p on the menu. Press enter key.
The adjustment will start automatically.
5) If ADC calibration is successful, “ADC RGB Success” is
displayed. If ADC calibration is failure, “ADC RGB Fail”
is displayed.
6) If ADC calibration is failure, after recheck ADC pattern or
condition retry calibration. Error message refer to 5).

(2) ADC 1920*1080 RGB

1) Check connected condition of Component & RGB cable
to the equipment
2) Give a 1920*1080 Mode, 100 % Horizontal Color Bar
Pattern to RGB port.
(MSPG-925 Series -> model: 225 , pattern: 65 )
3) Change input mode as RGB and picture mode as “Standard”.
4) Press the In-start key on the ADJ remote control after at
least 1 min of signal reception. Then, select 7. External
ADC -> 1. COMP 1080p on the menu. Press enter key.
The adjustment will start automatically.
5) If ADC calibration is successful, “ADC RGB Success” is
displayed. If ADC calibration is failure, “ADC RGB Fail”
is displayed.
6) If ADC calibration is failure, after recheck ADC pattern or
condition retry calibration. Error message refer to 5).

Copyright © 2011 LG Electronics. Inc. All rights reserved. -9- LGE Internal Use Only
Only for training and service purposes
4.2. EDID(The Extended Display Identification * Physical Add & Checksum(HDMI1/2/3/4)
Data)/DDC(Display Data Channel) download INPURT 9Eh/9Fh(Physical Add) FFh(Checksum)
(1) Overview HDMI 1 10 00 11
It is a VESA regulation. A PC or a MNT will display an HDMI 2 20 00 01
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”. HDMI 3 30 00 F1

(2) Equipment
- Adjust remote control
4.3. White Balance Adjustment
- Since embedded EDID data is used, EDID download JIG, 4.3.1 Overview
HDMI cable and D-sub cable are not need. (1) W/B adj. Objective & How-it-works
(2) Objective: To reduce each Panel’s W/B deviation
(3)Download method (3) How-it-works : When R/G/B gain in the OSD is at 192, it
1) Press Adjust key on the Adjustment remote control then means the panel is at its Full Dynamic Range. In order to
select “[Link] D/L”, By pressing Enter key, enter EDID prevent saturation of Full Dynamic range and data, one of
D/L menu. R/G/B is fixed at 192, and the other two is lowered to find
2) Select [Start] button by pressing Enter key, HDMI1/ the desired value.
HDMI2/ HDMI3/ HDMI4/ RGB are Writing and display (4) Adjustment condition : normal temperature
OK or NG 1) Surrounding Temperature : 25 ºC ± 5 ºC
2) Warm-up time: About 5 Min
For Analog EDID For HDMI EDID
3) Surrounding Humidity : 20 % ~ 80 %
D-sub to D-sub DVI-D to HDMI or HDMI to HDMI
4.3.2 Equipment
1) Color Analyzer: CA-210 (LED Module : CH 14)
2) Adjustment Computer(During auto adj., RS-232C protocol is
needed)
3) Adjust Remote control
4) Video Signal Generator MSPG-925F 720p/216-Gray
(Model: 217, Pattern: 78)
-> Only when internal pattern is not available
(4) EDID DATA A Color Analyzer Matrix should be calibrated using CS-1000
A RGB

0 1 2 3 4 5 6 7 8 9 A B C D E F 4.3.3. Equipment connection MAP

0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 01 15 01 03 68 10 09 78 0A EE 91 A3 54 4C 99 26
Co lo r Analyzer
20 0F 50 54 A1 08 00 71 40 81 C0 81 00 81 80 95 00
Probe RS -232C
30 90 40 A9 C0 B3 00 02 3A 80 18 71 38 2D 40 58 2C
Co m p ut er
40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30 RS -232C
RS -232C
50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
Pat t ern Generat o r
60 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
Signal Source
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 98
* If TV internal pattern is used, not needed

4.3.4. Adj. Command (Protocol)

A HDMI(FHD HDMI 1.3, Except 3D)
<Command Format>
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
LEN CMD VAL CS
10 01 15 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 71 4F 81 C0 81 00 81 80 95 00
- LEN: Number of Data Byte to be sent
30 90 40 A9 C0 B3 00 02 3A 80 18 71 38 2D 40 58 2C
- CMD: Command
40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30
- VAL: FOS Data value
50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 39
- CS: Checksum of sent data
60 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC
- A: Acknowledge
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 7F
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
80 02 03 26 F1 4E 10 1F 84 13 05 14 03 02 12 20 21
90 22 15 01 26 15 07 50 09 57 07 67 03 0C 00 XX XX
A0 80 2D E3 05 03 01 01 1D 80 18 71 1C 16 20 58 2C
B0 25 00 A0 5A 00 00 00 9E 01 1D 00 80 51 D0 1A 20
C0 6E 88 55 00 A0 5A 00 00 00 1A 02 3A 80 18 71 38
D0 2D 40 58 2C 45 00 A0 5A 00 00 00 1E 66 21 50 B0
E0 51 00 1B 30 40 70 36 00 A0 5A 00 00 00 1E 00 00
F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 XX

Copyright © 2011 LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
 A RS-232C Command used during auto-adjustment. (2) Manual adj. method
RS-232C COMMAND 1) Set TV in Adj. mode using POWER ON.
Explanation 2) Zero Calibrate the probe of Color Analyzer, then place it
[CMD ID DATA]
on the center of LCD module within 10 cm of the surface.
wb 00 00 Begin White Balance adj.
3) Press ADJ key -> EZ adjust using adj. R/C -> 7. White-
wb 00 10 Gain adj.(internal white pattern) Balance then press the cursor to the right (KEY G).
wb 00 1f Gain adj. completed (When KEY(G) is pressed 216 Gray internal pattern will
wb 00 20 Offset adj.(internal white pattern) be displayed)
wb 00 2f Offset adj. completed 4) One of R Gain / G Gain / B Gain should be fixed at 192,
wb 00 ff End White Balance adj.(Internal pattern disappears)
and the rest will be lowered to meet the desired value.
5) Adj. is performed in COOL, MEDIUM, WARM 3 modes
Ex) wb 00 00 -> Begin white balance auto-adj. of color temperature.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data A If internal pattern is not available, use RF input. In EZ
jb 00 c0 Adj. menu [Link] Balance, you can select one of 2
... Test-pattern: ON, OFF. Default is inner(ON). By selecting
... OFF, you can adjust using RF signal in 216 Gray pattern.
wb 00 1f -> Gain adj. completed
*(wb 00 20(Start), wb 00 2f(end)) -> Off-set adj. A Adj. condition and cautionary items
wb 00 ff -> End white balance auto-adj. 1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to
A Adj. Map isolate adj. area into dark surrounding.
ITEM Command Data Range(Hex.) Default 2) Probe location
: Color Analyzer (CA-210) probe should be within 10
Cmd 1 Cmd 2 Min Max (Decimal)
cm and perpendicular of the module surface (80° ~
Cool R-Gain j g 00 C0
100°)
G-Gain j h 00 C0 3) Aging time
B-Gain j i 00 C0 - After Aging Start, Keep the Power ON status during
R-Cut 5 Minutes.
G-Cut
- In case of LCD, Back-light on should be checked
using no signal or Full-white pattern.
B-Cut
Medium R-Gain j a 00 C0
4.3.6. Reference (White Balance Adj. coordinate and
G-Gain j b 00 C0
color temperature)
B-Gain j c 00 C0 A Luminance : 204 Gray
R-Cut A Standard color coordinate and temperature using CS-1000
G-Cut (over 26 inch)
B-Cut Mode Color Coordination Temp ∆UV
Warm R-Gain j d 00 C0
x y
G-Gain j e 00 C0
COOL 0.269 0.273 13000 K 0.0000
B-Gain j f 00 C0
R-Cut MEDIUM 0.285 0.293 9300 K 0.0000
G-Cut WARM 0.313 0.329 6500 K 0.0000

4.3.5. Adj. method A Standard color coordinate and temperature using CA-210
(1) Auto adj. method (CH 9)
1) Set TV in adj. mode using POWER ON key.
2) Zero calibrate probe then place it on the center of the Mode Color Coordination Temp ∆UV
Display. x y
3) Connect Cable (RS-232C) COOL 0.269 ± 0.002 0.273 ± 0.002 13000 K 0.0000
4) Select mode in adj. Program and begin adjustment.
5) When adj. is complete (OK Sign), check adj. status pre MEDIUM 0.285 ± 0.002 0.293 ± 0.002 9300 K 0.0000
mode. (Warm, Medium, Cool) WARM 0.313 ± 0.002 0.329 ± 0.002 6500 K 0.0000
6) Remove probe and RS-232C cable to complete adj.

A W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need.

Copyright © 2011 LG Electronics. Inc. All rights reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
4.3.7. ALELF & EDGE LED White banlance table 4.5. EYE-Q function check
- ALELF&EDGE LED module change color coordinate Step 1) Turn on TV.
because of aging time. Step 2) Press EYE key of Adjustment remote control.
- Apply under the color coordinate table, for compensated Step 3) Cover the Eye Q II sensor on the front of the using
aging time. your hand and wait for 6 seconds.
- EDGE LED - LGD Only Step 4) Confirm that R/G/B value is lower than 10 of the “Raw
Aging Time Cool Medium Warm Data (Sensor data, Back light)”. If after 6 seconds,
GP3 (Min.) X Y X Y X Y R/G/B value is not lower than 10, replace Eye Q II
sensor.
269 273 285 293 313 329
Step 5) Remove your hand from the Eye Q II sensor and wait
1 0-2 279 288 295 308 319 338
for 6 seconds.
2 3-5 278 286 294 306 318 336 Step 6) Confirm that “ok” pop up. If change is not seen,
3 6-9 277 285 293 305 317 335 replace Eye Q II sensor.
4 10-19 276 283 292 303 316 333
5 20-35 274 280 290 300 314 330
6 36-49 272 277 288 297 312 327
7 50-79 271 275 287 295 311 325
8 80-149 270 274 286 294 310 324
9 Over 150 269 273 285 293 309 323

4.6. Local Dimming Function Check

Step 1) Turn on TV.
Step 2) At the Local Dimming mode, module Edge Backlight
moving right to left Back light of IOP module moving.
Step 3) Confirm the Local Dimming mode.
Step 4) Press “exit” key.

4.4. Wireless function check

Step 1) Connect set and Dongle of Wireless to Cable of HDMI
& TTA 20Pin
Step 2) At OSD of SET, check the message like Fig 3. Local Dimming Demo (Edge LED Model)
Step 3) Detach Cable of Wireless Dongle

Connect Local Dimming Demo (IOP & ALEF Model)

Fig.1 Fig.2 4.7. Magic Motion Remote control test

- Equipment : RF Remote control for test, IR-KEY-Code
Remote control for test
- You must confirm the battery power of RF-Remote control
before test(recommend that change the battery per every lot)
- Sequence (test)
1) if you select the ‘start(Mute)’ key on the controller, you
can pairing with the TV SET.
2) You can check the cursor on the TV Screen, when select
the ‘OK’ key on the controller
3) You must remove the pairing with the TV Set by select
‘OK’ Key + ‘Mute’ key on the controller for 5 seconds.
Fig.3 Connect the Dongle

Copyright © 2011 LG Electronics. Inc. All rights reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
4.9 Option selection per country 5. Audio
(1) Overview
- Option selection is only done for models in NON-AU/-ID/- No. Item Min. Typ. Max. Unit
SG/-MY/-VN/-IL/-ZA/-IR 1. Audio practical max 9.0 10.0 12.0 W EQ Off
- Applied model: LB12C/D/E Chassis applied Asia/MEA Output, L/R AVL Off
model (Distortion=10 % 8.5 8.9 9.8 Vrms Clear Voice Off
max Output)
(2) Method
2. Speaker (8 Ω 10.0 15.0 W EQ On
1) Press ADJ key on the Adjustment remote control, then
select Country Group Menu Impedance) AVL On
2) Depending on destination, select Country Group Code Clear Voice On
12 or Country Group A-ASIA. Measurement condition:
3) Press ADJ key on the Adjustment remote control, then 1. RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
select Area Option. 2. CVBS, Component: 1 KHz sine wave signal 0.5 Vrms
4) Depending on Area code number, select Default Lang., 3. RGB PC: 1 KHz sine wave signal 0.7 Vrms
Wi-Fi Frequency, Lang Gr., Teletext Lang Gr., I II Save,
HDEV, MONO, Location.
6. USB S/W download(option, service only)
4.10. Tool Option selection 1) Put the USB Stick to the USB socket.
- Method : Press Adj. key on the Adjustment Remote Control, 2) Automatically detecting update file in USB Stick.
then select Tool option. - If your downloaded program version in USB Stick is Low,
Module Tool 1 Tool 2 Tool 3 Tool 4 Tool 5 Tool 6 Remark it didn’t work. But your downloaded version is High, USB
LGD 2486 780 3263 17594 8917 649 STD B/L: 60 data is automatically detecting.
3) Show the message “Copying files from memory”.

4.11. Ship-out mode check(In-stop)

After final inspection, press IN-STOP key of the Adjustment
remote control and check that the unit goes to Stand-by
mode.

4.12. GND and Internal Pressure check

(1) Method
1) GND & Internal Pressure auto-check preparation
- Check that Power Cord is fully inserted to the SET.
(If loose, re-insert)
2) Perform GND & Internal Pressure auto-check
- Unit fully inserted Power cord, Antenna cable and A/V
arrive to the auto-check process.
- Connect D-terminal to AV JACK TESTER 4) Updating is starting.
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.
(Remove CORD, A/V form AV JACK BOX)
- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow
the pallet to move on to next process.

(2) Checkpoint 5) Updating Completed, The TV will restart automatically.

• TEST voltage 6) If your TV is turned on, check your updated version and
- GND: 1.5 KV / min at 100 mA Tool option. (explain the Tool option, next stage)
- SIGNAL: 3 KV / min at 100 mA * If downloading version is more high than your TV have,
• TEST time: 1 second TV can lost all channel data. In this case, you have to
• TEST POINT channel recover. if all channel data is cleared, you didn’t
- GND TEST = POWER CORD GND & SIGNAL CABLE have a DTV/ATV test on production line.
METAL GND
- Internal Pressure TEST = POWER CORD GND & LIVE * After downloading, have to adjust TOOL OPTION again.
& NEUTRAL 1) Push “IN-START” key in service remote control.
• LEAKAGE CURRENT: At 0.5 mArms 2) Select “Tool Option 1” and push “OK” key.
3) Push in the number. (Each model has their number.)

Copyright © 2011 LG Electronics. Inc. All rights reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
 EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

710
700

910
400

900
521
540

* Stand Base + Body

530

* Set + Stand
800

A10
LV1

A5
200

A2

A21
120
320

511
310

510
300

Copyright LG Electronics. Inc. All rights reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
 NAND FLASH MEMORY 8Gbit 16Gbit Boot ROM Device Select - (FA4,FAD7,FAD2,FAD1) Strap Setting
+3.3V_Normal
+3.3V_Normal
+3.3V_Normal 0000: ST Micro M25P or compatible Serial Flash
IC102-*1
TH58DVG4S0ETA20 0010: 8-bit 512Mbit 512B page SLC NAND Flash devices
IC102 0100: 8-bit 128, 256Mbit 512B page SLC NAND Flash devices
TC58DVG3S0ETA00 0110: 8-bit 1Gbit 2KB page SLC NAND Flash devices
R113 R117 R122 R127 R154 R157 R160 R164 R167 R170 R175 R177 R179 R181 R183 R187 R192
10K 10K 10K 10K 1000: 8-bit 2Gbit, 4Gbit, 8Gbit 2KB page SLC NAND Flash devices 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K
NC_1 NC_26 OPT OPT 1010: 8-bit 16Gbit, 32Gbit 4KB page SLC NAND Flash devices (O) OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT
1 DEV_NAND_16Gbit 48 CI_ADDR[4]
NC_1 NC_28 0001: 8-bit 8/16/32Gbit 2KB page MLC NAND Flash devices
1 NAND_8Gbit 48 NC_2 NC_25 NAND_DATA[7] 0011: 8-bit 16/32Gbit 4KB page MLC NAND Flash devices NAND_DATA[0]
2 47
NC_2 NC_27 NAND_DATA[2] 0101: 8-bit 32Gbit 8KB page MLC NAND Flash devices
2.7K

2 47 NC_3 NC_24 CI_ADDR[7]

0111: 3B dual IO Serial Flash
3 46 NAND_DATA[1] 1001: NAND_DATA[6]
NC_3 NC_26 BB dual IO Serial Flash
3 46 NC_4 NC_23 R114 R118 R123 R128 1011: fast Serail Flash > 50Mhz
4 45 10K 10K 10K 10K CI_ADDR[6]
NC_4 NC_25 NAND_DATA[0-7] OPT OPT 1100: OneNAND Flash (always 16-bit)
4 45 NC_5 I/O8 NAND_CLE
1110: Reserved
R107

5 44 NAND_DATA[4]
NC_5 I/O8 1101, 1111: Reserved
5 44 NAND_DATA[7] RY/BY2 I/O7 CI_ADDR[9]
16Gbit 6 43
R149 0 NC_6 I/O7 CI_ADDR[11]
6 43 NAND_DATA[6] RY/BY1 I/O6
7 42 CI_ADDR[12]
RY/BY I/O6
NAND_RBb 7 42 NAND_DATA[5] RE I/O5 CI_ADDR[13]
8 41
RE I/O5 CI_ADDR[8]
NAND_REb 8 41 NAND_DATA[4] CE1 NC_22
CE NC_24
9 40 NAND ECC (FA3, FA2, FALE) NAND_DATA[3]
NAND_CEb 9 40 CE2 PSL NAND_DATA[5]
16Gbit 16Gbit 10 39 +3.3V_Normal
NC_7 PSL 0
NAND_CEb2 R148 0 10 39 R151 NC_6 NC_21 R155 R158 R161 R165 R168 R171 R176 R178 R180 R182 R184 R188 R193
11 38 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K
NC_8 NC_23
C102 11 38 VCC_1 VCC_2 OPT OPT OPT
4700pF 12 37 R111 R115 R119
VCC_1 VCC_2 +3.3V_Normal 10K 10K 10K
12 37 VSS_1 VSS_2 OPT 000 = ECC disabled
C101 13 36 OPT
VSS_1 VSS_2 C104 10uF CI_ADDR[3] 001 = ECC 1-bit repair
0.1uF 13 36 NC_7 NC_20
10V 010 = ECC 4-bit BCH (O)
14 35 CI_ADDR[2]
NC_9 NC_22 011 = ECC 8-bit BCH, 27 byte spare
14 35 C103 NC_8 NC_19 NAND_ALE 100 = ECC 12-bit BCH, 27 byte spare
0.1uF 15 34
NC_10 NC_21 R112 R116 R120 101 = ECC 8-bit BCH, 16 byte spare NAND_DATA[0]:
15 34 CLE NC_18 10K 10K 10K 110, 111 = Reservedd 0: System is LITTLE endian (O) CI_ADDR[9],CI_ADDR[11],CI_ADDR[12],CI_ADDR[13]
16 33 OPT TVM Crystal oscillator bias/gain control
CLE NC_20 1: System is BIG endian
NAND_CLE 16 33 ALE I/O4 0000: 210uA
17 32
ALE I/O4 CI_ADDR[7]: 0001: 390uA
NAND_ALE 17 32 NAND_DATA[3] WE I/O3 0: Disable EDID automatic Downloading from Flash (O) 0010: 570uA
18 31
WE I/O3 1: Enable EDID automatic Downloading from Flash 0011: 730uA
NAND_WEb 18 31 NAND_DATA[2] WP I/O2 0100: 890uA (O)
19 30
WP I/O2 NAND_DATA[6] : 0111: 1290uA
Write Protection +3.3V_Normal 19 30 NAND_DATA[1] NC_9 I/O1 0: Disable OSC clock output on chip Pin (O) 1000: 1416uA
20 29
NC_11 I/O1 1: Enable OSC clock output on chip pin. 1111: 2196uA
- High : Normal Operation 20 29 NAND_DATA[0] NC_10 NC_17 DUAL COMPONENT 0101, 0110, 1001, 1010, 1011, 1100, 1101, 1110: Reserved
R103
4.7K

- Low : Write Protection 21 28

OPT

NC_12 NC_19 CI_ADDR[6]:

21 28 NC_11 NC_16 0: Host MIPS run at 500 MHz (O) CI_ADDR[8]:
NC_13 NC_18
22 27 IC102 1ST : EAN61000101 2ND : T-TH58DVG4S0ETA20 1: Host MIPS run at 250 MHz 0: RESETOUTb (in On/Off only) stay asserted until software releases them.
22 27 NC_12 NC_15 1: Fix amount of delay for de-assertion on RESETOUTb (in On/IOff only)
FLASH_WP 23 26
NC_14 NC_17 NAND_CLE: at end of RESETb pulse (O)
23 26 NC_13
24 25
NC_14 IC102-*1 0: Differential Oscillators TVM not bypassed (O)
NC_15 NC_16 1: Differential Oscillators TVM bypassed NAND_DATA[3]:
24 25 0: MIPS will boot from external flash (O)
NAND_DATA[4]: 1: MIPS will boot from ROM
0: 27MHz TVM Crystal Frequency
1: 54MHz TVM Crystal Frequency (O) NAND_DATA[5]:
0: FLASH MODE (O)
1: BSC_SLAVE(BBS) MODE

BCM_NVM_256K
IC103-*1
+3.3V_Normal
NVRAM AT24C256C-SSHL-T

A0
1 8
VCC

A1 WP
R196 2 7
IC101 10K A2 SCL
LGE35230(BCM35230KFSBG) +3.3V_Normal 3 6

RGB_DDC_SDA GND SDA

4 5
S
B
D

NON_BCM_CAP
B5 AE27 BCM_NVM_1M
HDMI_CLK- HDMI0_CLKN TXOUT0_L0N TXB4P Q101 IC101

4.7K

4.7K
IC103 +3.3V_Normal

OPT
R173

R174
C5 AE28
HDMI_CLK+ HDMI0_CLKP TXOUT0_L0P TXB4N BSS83 LGE35230(BCM35230KFSBG) M24M01-HRMN6TP
G

AF27
TXOUT0_L1N TXB3P NAND_DATA[0-7]
A4 AF28
HDMI_RX0- HDMI0_D0N TXOUT0_L1P TXB3N C118 NC VCC
B4 AG27 NON_BCM_CAP 1 8 Write Protection
HDMI_RX0+ HDMI0_D0P TXOUT0_L2N TXBCLKP 0.1uF AG6 AB1 NAND_DATA[7]
AG28 16V 54MHz_XTAL_P TVM_XTALIN FAD_7 R169
TXOUT0_L2P TXBCLKN AB3 NAND_DATA[6] 0 E1 WP - Low : Normal Operation
+3.3V_Normal A3 AE26 FAD_6 2 7
HDMI_RX1- HDMI0_D1N TXCLK_LN TXB2P AF6 AC1 NAND_DATA[5] A8’h - High : Write Protection
B3 AF26 54MHz_XTAL_N TVM_XTALOUT FAD_5
HDMI_RX1+ HDMI0_D1P TXCLK_LP TXB2N AC2 NAND_DATA[4] E2 SCL
AH27 +3.3V_Normal FAD_4 3 6 R190 33
TXB1P AC3 SCL3_3.3V
TXOUT0_L3N

4.7K
NAND_DATA[3]

OPT
R172
A2 AG26 FAD_3
R101 R105 R104 R195 HDMI_RX2- HDMI0_D2N TXOUT0_L3P TXB1N V5 AD2 NAND_DATA[2] VSS SDA
B2 AF25 LNB_INT IRRXDA FAD_2 4 5 R191 33
4.7K 4.7K 4.7K 4.7K HDMI_RX2+ TXB0P AD3 SDA3_3.3V
HDMI0_D2P TXOUT0_L4N NAND_DATA[1]
AE25 R198 FAD_1
TXOUT0_L4P TXB0N 10K AE2 NAND_DATA[0]
FAD_0
AB4
W2 FP_IN0
CEC RGB_DDC_SCL Y4
AH26
S
B
D

FP_IN1
TXOUT0_U0N TXA4P AG1
V4 AG25 FALE NAND_ALE
DDC0_SCL TXOUT0_U0P TXA4N Q102 AA4 AF1
W4 AE24 SPARE_ADC1 FCEB_0 NAND_CEb
DDC0_SDA TXOUT0_U1N TXA3P BSS83 Y5 AC5
AD24 SPARE_ADC2 FCEB_1 NAND_CEb2 X101-*2
G

TXOUT0_U1P TXA3N AE6

V3
V2
HDMI0_HTPLG_IN TXOUT0_U2N
AH25
AF24
TXACLKP
TXACLKN
C119 SC_ID
AB2
FS_IN1
FCEB_2
FCEB_3
AG5
/CI_CE1
/CI_CE2
54MHz X-TAL X-TAL_1
1
54MHz
4
GND_2

HDMI0_HTPLG_OUT TXOUT0_U2P 0.1uF AB5 GND_1 X-TAL_2

AE23 16V FS_IN2
TXCLK_UN TXA2P 2 3
D13 AD23 C113
HDMI_ARC HDMI0_ARC TXCLK_UP TXA2N AF3 12pF CRYSTAL_BCM_KDS
E6 AG24 NFWPB FLASH_WP R185 0 EAW58239604
HDMI0_RESREF TXOUT0_U3N TXA1P U3 AG2 54MHz_XTAL_N
AF23 VGA_SDA FWE NAND_WEb DAISHINKU CORPORATION.
TXA1N +3.3V_Normal U2 AE3 50V
R106 TXOUT0_U3P 3 2
AC22 VGA_SCL FRD NAND_REb X-TAL_2 GND_1 X101-*1
3K TXOUT0_U4N TXA0P AA5 R189 54MHz
AD22 FRDYB /PCM_WAIT 4 1 X-TAL_1 GND_2
TXOUT0_U4P TXA0N GND_2 X-TAL_1 1M
1 4
Y2 54MHz OPT
BCM_RX RDA X101 GND_1 X-TAL_2
BBS CONNECT R121 R126 R129 R131 Y1 AF2 R186 0 2 3
CI_ADDR[2-14] 54MHz_XTAL_P
AG23 DEBUG_BBS 1.2K 1.2K 1.2K 1.2K BCM_TX TDA FA_0 NAND_CLE C114 CRYSTAL_BCM_Sunny
TXOUT1_L0N TXD4P +3.3V_Normal AE1 12pF CRYSTAL_BCM_Lihom
AH23 P101 FA_1 NAND_RBb EAW58812611 EAW60763703
TXD4N 33 AA3 AC4 50V
TXOUT1_L0P SDA0_3.3V R135 CI_ADDR[2] SUNNY ELECTRONICS CORPORATION LIHOM CO., LTD.
AE22 TJC2508-4A BSCDATAA FA_2
TXOUT1_L1N TXD3P R136 33 AA2 AD5 CI_ADDR[3]
AE21 SCL0_3.3V BSCCLKA FA_3
TXOUT1_L1P TXD3N AD4 CI_ADDR[4]
AF22 FA_4
TXOUT1_L2N TXDCLKP VCC H3 AE4 CI_ADDR[5]
AH22 1 SCL2_3.3V RDB/GPIO FA_5
TXOUT1_L2P TXDCLKN C106 R109 R110 H2 AE5 CI_ADDR[6]
AG22 1.5K 1.5K SDA2_3.3V TDB/GPIO FA_6
TXCLK1_LN TXD2P 4.7uF AD6
AF21 CI_ADDR[7]
SCL R199 22 FA_7
TXCLK1_LP TXD2N 2 H4 AH3 CI_ADDR[8]
AG21 R197 22 BSC_S_SCL FA_8
TXOUT1_L3N TXD1P H5 AF4 CI_ADDR[9]
AF20 BSC_S_SDA FA_9
TXOUT1_L3P TXD1N SDA AH4 CI_ADDR[10]
AD21 3 +3.3V_Normal FA_10
TXOUT1_L4N TXD0P C107 C108 C109 C110 AG4 CI_ADDR[11]
AC21 33pF 33pF 33pF 33pF FA_11
TXOUT1_L4P TXD0N R141 4.7K F25 AF5 CI_ADDR[12]
GND 50V 50V 50V 50V NMIB FA_12
4 DVB_S DVB_S AG3 CI_ADDR[13] +3.3V_Normal
FA_13
W5 AH2 CI_ADDR[14]
AG20 DVB_S Option: apply EU Satellite model PCM_5V_CTL POWER_CTRL FA_14
TXOUT1_U0N TXC4P AH5
AH20 5V_HDMI_1 OPT FA_15
TXOUT1_U0P TXC4N R142 22 U5 R146 10K R147 R150 R153 R156 R159 R162 R166
AD19 AON_HSYNC 1K 1K 1K 1K 1K 1K 1K
TXOUT1_U1N TXC3P 5V_HDMI_2 U4
AE19 R143 22
AON_VSYNC
TXOUT1_U1P TXC3N OPT AD15
AF19 FOR HDMI STANDARD 5V_HDMI_3 TRSTB
TXOUT1_U2N TXCCLKP APPLY ONLY WHEN CONNECT TO PULL-UP GPIO OPT W3 AF14
AH19 R144 22
AON_GPIO_36 TDI/GPIO
TXOUT1_U2P TXCCLKN R130 5V_HDMI_4 R145 22 W1 AH14
AE18 OPT 2K AON_GPIO_37 TDO R163
TXCLK1_UN TXC2P OPT AD14 1K
AD18 +3.3V_Normal TMS/GPIO
TXCLK1_UP TXC2N AB6 AG14
AG19 AON_RESETOUTB TCK/GPIO
TXOUT1_U3N TXC1P R132 4.7K Y6 AC16
AF18 TVM_BYPASS DINT/GPIO
TXOUT1_U3P TXC1N
AG18 R139 0
TXOUT1_U4N TXC0P SRST
AF17
TXOUT1_U4P TXC0N +3.3V_Normal +3.3V_Normal Y3 AH7
SOC_RESET RESETB AVS_VFB
G24 AG7
RESETOUTB AVS_VSENSE
AD7 SRST
AC18 R194 R124 AVS_RESETB
LT0VCAL_MONITOR 2.7K 1K J6 AF7
AH16 OPT TMODE AVS_NDRIVE_1
GPIO_BL_ON W6 AH8
AG16 R108 10K TESTEN AVS_PDRIVE_1
BL_PWM/GPIO A_DIM +3.3V_Normal
R125
C105 1K
2.2uF C111 0.01uF F7 C6
10V VDAC_VREG VDAC_1 DTV/MNT_V_OUT
E7 D7
C112 0.1uF VDAC_RBIAS VDAC_2
R140
560
1%

BCM REFRENCE is 562ohm

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230 2010.09.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN & NAND FLASH 1

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 POWER 2.5V
+2.5V_BCM35230 ADAC_AVDD25 CORE 0.9V
+2.5V_BCM35230 AADC_AVDD25
+0.9V_CORE HDMI_AVDD +0.9V_CORE USB_AVDD +0.9V_CORE VAFE2_DVDD
L202 L205 L209
BLM18PG121SN1D BLM18PG121SN1D L214 L219
+3.3V_Normal
BLM18PG121SN1D BLM18PG121SN1D BLM18PG121SN1D
+0.9V_CORE +0.9V_CORE
NFM18PS105R0J NFM18PS105R0J C249 C253 C256 C258
C233 C204 10uF 10uF 0.1uF 0.1uF C280 C284 C285 C288 C292 C296 C299
C261 C263 C267 C271 C274 22uF 22uF 4.7uF 0.1uF
6.3V 6.3V 10V 10V 10uF 4.7uF 0.1uF 0.01uF 22uF 0.1uF 4.7uF 0.1uF
C225 C221 C223 C247 10V
BCM_FRC/URSA5

0.22uF 0.1uF 0.01uF IN OUT IN OUT 22uF

6.3V
S_TUNER
T2_TUNER
FRC2/URSA5

GND GND
R254

R256

R257
R253

R255

PHM
R251

R252

OLED
R250

FHD

1K

1K

1K
1K

1K
1K

1K
1K

+2.5V_BCM35230 EPHY_VDD25 +2.5V_BCM35230

+0.9V_CORE PLL_AUD_AVDD +0.9V_CORE VAFE3_DVDD +0.9V_CORE PLL_MAIN_AVDD
L203
BLM18PG121SN1D L210 L215 L217
NFM18PS105R0J +3.3V_Normal BLM18PG121SN1D BLM18PG121SN1D BLM18PG121SN1D
MODEL_OPT_0 C244 C259 C260 C262 C266 C270 C272
6.3V C251 C252 C255
0.1uF 4.7uF 0.1uF 10uF 4.7uF 10uF 4.7uF 0.1uF 0.01uF C277 C281 C294 C297
MODEL_OPT_1 16V 10V 10V 4.7uF 0.1uF C287 C290 4.7uF 0.1uF
C232 C234 C236 C238 IN OUT C248 4.7uF 0.1uF
MODEL_OPT_2 4.7uF 0.1uF 0.1uF 4.7uF 10uF
10V 10V GND 10V
MODEL_OPT_3
MODEL_OPT_4
+2.5V_BCM35230 VAFE2_VDD25
MODEL_OPT_5 +0.9V_CORE PLL_MIPS_AVDD
L206 +0.9V_CORE PLL_VAFE_AVDD
+1.5V_DDR
MODEL_OPT_6 BLM18PG121SN1D L211 L218
BLM18PG121SN1D BLM18PG121SN1D
MODEL_OPT_7
NO_FRC/BCM_FRC

NO_FRC/FRC2

NO_T2_TUNER

NO_S_TUNNER

C295 C298
C203 C205 C207 C209 C211 C213 C215 C220 C222 C265 C269 C279 C282 4.7uF 0.1uF
NO_PHM
R260

R265
R261

10uF 10uF 4.7uF 4.7uF 0.1uF 0.1uF 0.01uF 0.1uF 0.01uF 4.7uF 0.1uF 4.7uF 0.1uF
R262

R263

R264

R266

R267
LCD

OPT
HD

10V 10V
1K

1K

10V 10V
1K

1K

1K

1K

1K

1K

+2.5V_BCM35230 VAFE3_VDD25 +2.5V_BCM35230 PLL_VAFE_AVDD25

L204 L207
BLM18PG121SN1D BLM18PG121SN1D

C254 C257 C264 C268 POWER 3.3V

C250
4.7uF 4.7uF 0.1uF 4.7uF 0.1uF
MODEL OPTION 10V +3.3V_Normal USB_AVDD33 +3.3V_Normal HDMI_AVDD33
BCM L212 L216
external
NO_FRC internal LG FRC2 BLM18PG121SN1D BLM18PG121SN1D
URSA5
FRC
C283
MODEL_OPT_0 0 0 1 1 C291 C293
0.1uF
4.7uF 0.1uF
MODEL_OPT_1 0 1 0 1

HIGH LOW IC101

+0.9V_CORE LGE35230(BCM35230KFSBG)
MODEL_OPT_2 FHD HD
+3.3V_Normal VDAC_AVDD33
MODEL_OPT_3 OLED LCD NON_BCM_CAP
L213
V12 K10 BLM18PG121SN1D
MODEL_OPT_4 DDR speed 1333 1600 VDDC_1 VSS_1
V7 K11
VDDC_2 VSS_2
MODEL_OPT_5 T2 Tuner Support Not Support M10 K12
VDDC_3 VSS_3 C286 C289
N10 L12 4.7uF 0.1uF
MODEL_OPT_6 S Tuner Support Not Support VDDC_4 VSS_4
P10 M12
VDDC_5 VSS_5
MODEL_OPT_7 PHM Enable Disable R10 N12
VDDC_6 VSS_6
T10 P12
VDDC_7 VSS_7
U10 R12
VDDC_8 VSS_8
V10 T12
close to soc VDDC_9 VSS_9
W10 U12
IC101 C217 V13
VDDC_10 VSS_10
W12
LGE35230(BCM35230KFSBG) 16V
L11
VDDC_11 VSS_11
K13
0.1uF 100
Non_CHB R241 +3.3V_Normal VDDC_12 VSS_12
M11 L13
IF_P VDDC_13 VSS_13 IC101
NON_BCM_CAP R212 L201 N11 M13
F26 C17 1K C218
100 P11
VDDC_14 VSS_14
N13
LGE35230(BCM35230KFSBG)
EPHY_VREF VI_IFP0 0.1uF R242 BLM18PG121SN1D
D26 B17 16V VDDC_15 VSS_15 AADC_AVDD25
EPHY_RDAC VI_IFM0 IF_N R11 P13
R211 D15 VDDC_16 VSS_16 NON_BCM_CAP
VDDR_AGC +3.3V_Normal T11 R13
6.04K F27 VDDC_17 VSS_17 F19 F20
EPHY_TDP EPHY_TDP C229 U11 T13 AADC_AVDD25 AADC_AVSS
F28 B16 closed to soc VDDC_18 VSS_18 ADAC_AVDD25
0.1uF V11 U13
EPHY_TDN EPHY_TDN AGC_SDM_2
E27 A16 R213 2K VDDC_19 VSS_19 D25 G22
EPHY_RDP EPHY_RDP AGC_SDM_1 IF_AGC R233 R234 W11 W16 ADACA_AVDD25 ADACA_AVSS
E26 C216 0.01uF 1.2K 1.2K VDDC_20 VSS_20 D24 G21
EPHY_RDN EPHY_RDN V14 K14 ADACC_AVDD25 ADACC_AVSS
A15 VDDC_21 VSS_21 E24 F22
GPIO_0 SDA1_3.3V L18 L14 ADACD_AVDD25 ADACD_AVSS
C16 VDDC_22 VSS_22 EPHY_VDD25
GPIO_1 SCL1_3.3V M18 M14
F5 G28 VDDC_23 VSS_23 F24 F23
USB_MONCDR GPIO_2 3D_SYNC C227 C231 N18 N14 EPHY_BVDD25 EPHY_AVSS
+3.3V_Normal E5 G26 33pF 33pF NON_NTP VDDC_24 VSS_24 E25
USB_RREF GPIO_3 NON_NTP P18 P14 EPHY_AVDD25
C201 R210 50V 50V VDDC_25 VSS_25
100pF 4.87K +3.3V_Normal R18 R14
1% C2 VDDC_26 VSS_26 HDMI_AVDD
OPT SIDE_USB_DM USB_PORT1DN T18 T14
R287 D1 W14 VDDC_27 VSS_27
10K SIDE_USB_DP USB_PORT1DP PCI_VIO_0 U18 U14 HDMI_AVDD33
W15 VDDC_28 VSS_28 D5 F6
WIFI PCI_VIO_1 V18 K15 HDMI0_AVDD HDMI0_AVSS_1
E1 W13 VDDC_29 VSS_29 D4 G6
SIDE_USB_OCD1 USB_PWRFLT_1/GPIO PCI_VIO_2 W18 L15 +2.5V_BCM35230 HDMI0_AVDD33 HDMI0_AVSS_2
D2 VDDC_30 VSS_30
SIDE_USB_CTL1 USB_PWRON_1/GPIO V15 M15
VDDC_31 VSS_31 AE20 AB22
R286 L19 N15 LT0VDD25_1 LT0VSS_1
10K B1 J5 R280 VDDC_32 VSS_32 AD20 AB21
WIFI_DM USB_PORT2DN GPIO_4 M_REMOTE_RX M19 P15 LT0VDD25_2 LT0VSS_2
WIFI C1 R5 22 VDDC_33 VSS_33 AC20 AB19
WIFI_DP USB_PORT2DP GPIO_5 MODEL_OPT_0 N19 R15 +2.5V_BCM35230 LT0VDD25_3 LT0VSS_3
V6 VDDC_34 VSS_34 AB20 AC19
GPIO_6 CI_DET P19 T15 LT0VDD25_4 LT0VSS_4
C3 H6 VDDC_35 VSS_35 AB18
SIDE_USB_OCD2 USB_PWRFLT_2/GPIO GPIO_7 M_RFModule_RESET R19 U15 LT0VSS_5
C4 AE15 VDDC_36 VSS_36 C275 AB17
SIDE_USB_CTL2 USB_PWRON_2/GPIO GPIO_70 EPHY_ACTIVITY T19 K16 LT0VSS_6
AF15 VDDC_37 VSS_37 0.1uF AC17
GPIO_71 EPHY_LINK U19 L16 OPT LT0VSS_7
PCM_TS_DATA[0-7] AG15 R214 22 +3.3V_Normal VDDC_38 VSS_38
GPIO_72 DTV_ATV_SELECT V19 M16
M4 AF16 R215 22 VDDC_39 VSS_39 USB_AVDD D14 SPDIF_IN_AVDD25 F15
PCM_TS_CLK TCLKA/GPIO GPIO_73 RF_SWITCH_CTL_2 +1.5V_DDR W19 N16
L5 AD16 R281 22 VDDC_40 VSS_40 SPDIF_IN_AVSS
PCM_TS_DATA[0] R240 V16 P16
TDATA_0/GPIO GPIO_74 MODEL_OPT_1 USB_AVDD33
PCM_TS_DATA[1] M5 AE16 R282 22 2.7K VDDC_41 VSS_41 E4 G7
TDATA_1/GPIO GPIO_75 MODEL_OPT_2 V17 R16 USB_AVDD USB_AVSS_1
PCM_TS_DATA[2] L6 AG17 R216 22 Place Cap VDDC_42 VSS_42 VDAC_AVDD33 D3 G8
TDATA_2/GPIO GPIO_76 MODEL_OPT_3 Very close to R22 Ball T16 USB_AVDD33 USB_AVSS_2
PCM_TS_DATA[3] N3 AH17 R228 22 VSS_43
TDATA_3/GPIO GPIO_77 PWM_DIM L10 U16
PCM_TS_DATA[4] N1 AE17 R230 22 MLG1005S22NJT POR_VDD VSS_44 VAFE2_DVDD D6 G9
TDATA_4/GPIO GPIO_78 L/DIM0_VS K17 VDAC_AVDD33 VDAC_AVSS
PCM_TS_DATA[5] N2 AD17 BCM_L/DIM C224 C226 VSS_45 VAFE2_VDD25
OPT TDATA_5/GPIO GPIO_79 INSTANT_MODE L220 L17
R201 0 PCM_TS_DATA[6] M3 1uF 0.1uF VSS_46 D18 G20
TDATA_6/GPIO L22 M17 VAFE2_DVDD VAFE2_VSS_1
M2 25V 16V VDDR1_1 VSS_47 E17 E18
PCM_TS_DATA[7] OPT OPT AA28 N17
TDATA_7/GPIO Place as close as possible to the pad VAFE2_AVDD25_1 VAFE2_VSS_2
L4 AB13 +3.3V_Normal VDDR1_2 VSS_48 C212 C214 D16 G18
PCM_TS_SYNC TSTRTA/GPIO PCI_AD05 V28 P17 VAFE2_AVDD25_2 VAFE2_VSS_3
N4 AC15 VDDR1_3 VSS_49 VAFE3_DVDD 390pF 390pF D17 G17
R28 R17
URSA_RESET

FRC2_RESET

PCM_TS_VAL TVLDA/GPIO PCI_AD06 50V 50V VAFE2_DVDD25 VAFE2_VSS_4

AB12 VDDR1_4 VSS_50 F18
R232-*1

FE_TS_DATA[0-7] F/NIM_EU_CN PCI_AD07 M28 T17 VAFE3_VDD25 VAFE2_VSS_5

R202 K6 AB11 VDDR1_5 VSS_51 D9 G16
J28 U17
4.7K

TU_TS_CLK
4.7K
R232

0 TCLKD/GPIO PCI_AD08 VAFE3_DVDD VAFE2_VSS_6

FE_TS_DATA[0] J4 AE14 R231-*1 0 VDDR1_6 VSS_52 D8 F16
TDATD_0/GPIO PCI_AD09/GPIO SC_DET/COMP2_DET K23 W17 VAFE3_AVDD25_1 VAFE2_VSS_7
FE_TS_DATA[1] R203 0 F/NIM_EU_CN K5 AG13 VDDR1_7 VSS_53 E8
TDATD_1/GPIO PCI_AD10/GPIO CHB_RESET FRC2_RESET M22 K18 C208 C210 VAFE3_AVDD25_2
F/NIM_EU_CN J2 AH13 VDDR1_8 VSS_54 use only for A0/B0 chip F9 G13
FE_TS_DATA[2] R204 0 R231 100 FRC_RESET T22 K19 390pF 390pF
TDATD_2/GPIO PCI_AD11/GPIO VAFE3_AVDD25_3 VAFE3_VSS_1
FE_TS_DATA[3] R205 0 F/NIM_EU_CN J3 AF13 VDDR1_9 VSS_55 C210-*1 50V 50V E9 G12
TDATD_3/GPIO PCI_AD12/GPIO TW9910_RESET URSA_RESET T23 H7 VAFE3_DVDD25 VAFE3_VSS_2
VDDR1_10 VSS_56 220pF BCM_C0
FE_TS_DATA[4] R206 0 F/NIM_EU_CN K2 AE13 F8 F12
TDATD_4/GPIO PCI_AD13/GPIO AV2_CVBS_DET Place Cap U22 G14 50V POR_VDD25 VAFE3_VSS_3
FE_TS_DATA[5] R207 0 F/NIM_EU_CN K1 AD12 R218 22 Very close to R22 Ball VDDR1_11 VSS_57 PLL_AUD_AVDD G11
TDATD_5/GPIO PCI_AD14/GPIO RF_BOOSTER_CTL Y22 AB16 BCM_A0/B0 VAFE3_VSS_4
F/NIM_EU_CN K3 AF12 VDDR1_12 VSS_58 Place as close as possible to the pad G10
FE_TS_DATA[6] R208 0 DSUB_DET C242 R7 PLL_MAIN_AVDD
TDATD_6/GPIO PCI_AD15/GPIO VAFE3_VSS_5
FE_TS_DATA[7] R209 0 F/NIM_EU_CN L1 AG10 0.1uF VSS_59 G25 F10
TDATD_7/GPIO PCI_AD16/GPIO PCM_RST R22 M6 PLL_AUD_AVDD VAFE3_VSS_6
CHBO_TS_CLK L3 AF10 DDR_LDO_VDDO VSS_60 PLL_MIPS_AVDD K4
TU_TS_SYNC R220 22 MODEL_OPT_4 AB23 PLL_VAFE_AVDD
CHBO_TS_SERIAL TSTRTD/GPIO PCI_AD17/GPIO PLL_MAIN_AVDD
L2 AE10 +3.3V_Normal VSS_61 AD25
TS_VAL_ERR TVLDD/GPIO PCI_AD18/GPIO DC_MREMOTE P7 PLL_MIPS_AVDD
CHBO_TS_SYNC AD10 VSS_62 PLL_VAFE_AVDD25 D11 AD26
PCI_AD19/GPIO DD_MREMOTE G15 W7 PLL_MIPS_AVSS
CHBO_TS_VAL_ERR AE9 VDDR3_1 VSS_63 D12 PLL_VAFE_AVDD
PCM_MDI[0-7] R221 22 BCM_L/DIM L/DIM0_MOSI H22 J7
PCI_AD20/GPIO +0.9V_CORE PLL_VAFE_AVDD25
P4 AE8 R222 22 BCM_L/DIM VDDR3_2 VSS_64
PCM_MCLKI MPEG_CLK/GPIO PCI_AD21/GPIO L/DIM0_SCLK G23 N7
PCM_MDI[0] T2 AC10 VDDR3_3 VSS_65 AE7 AC7
MPEG_D_0/GPIO PCI_AD22 AB9 AB10 TVM_OSC_AVDD TVM_OSC_AVSS
PCM_MDI[1] R3 AC11 VDDR3_4 VSS_66 C273
MPEG_D_1/GPIO PCI_AD23 K7 AC23 C276 +3.3V_Normal
PCM_MDI[2] R2 AC8 VDDR3_5 VSS_67 C202 C206 0.1uF 0.01uF U6
MPEG_D_2/GPIO PCI_AD24 AB15 AC6 AUX_AVDD33
P3 AB8 VDDR3_6 VSS_68 390pF 390pF OPT
PCM_MDI[3] L7 G19 50V 50V
MPEG_D_3/GPIO PCI_AD25
PCM_MDI[4] P2 VDDR3_7 VSS_69
MPEG_D_4/GPIO AB14 AA22
PCM_MDI[5] P1 AC14 VDDR3_8 VSS_70 C278
MPEG_D_5/GPIO PCI_CBE00 M7 J23
R6 AG12 VDDR3_9 VSS_71 0.1uF
PCM_MDI[6] R283 COMP1_DET N6 J22
MPEG_D_6/GPIO PCI_CBE01/GPIO 22
PCM_MDI[7] N5 AH10 VDDR3_10 VSS_72
MPEG_D_7/GPIO PCI_CBE02/GPIO MODEL_OPT_5 P6 K22
T4 AB7 VDDR3_11 VSS_73
PCM_MISTRT MPEG_SYNC/GPIO PCI_CBE03 +0.9V_CORE J25 Place as close as possible to the pad
P5 VSS_74
PCM_MIVAL_ERR MPEG_DATA_EN/GPIO N22
AG11 R223 22 VSS_75
PCI_DEVSELB/GPIO 3D_GPIO_0 +3.3V_Normal AA6 N23
AD11 R284 22 AON_VDDC_1 VSS_76
PCI_FRAMEB/GPIO MODEL_OPT_6 AA7 M25
R4 AE11 R224 22 AON_VDDC_2 VSS_77
MCIF_RESET/GPIO PCI_IRDYB/GPIO MODEL_OPT_7 Y7 P22
U1 AD13 AON_POR_VDD VSS_78
MCIF_SCLK/GPIO PCI_PAR/GPIO R25
T3 AE12 R235 100 VSS_79
MCIF_SCTL/GPIO PCI_PERRB/GPIO ERROR_OUT U7 V22
T1 AC12 R225 0 OPT AON_VDDR3 VSS_80
/PCM_IRQA MCIF_SDI/GPIO PCI_REQ1B W22
T5 AC13 R226 22 VSS_81
MCIF_SDO/GPIO PCI_SERRB/GPIO RF_SWITCH_CTL T7 W23
AH11 R285 22 AON_VDDR10_1 VSS_82
PCI_STOPB/GPIO 3D_GPIO_1 T6 V25
AF11 R227 22 AON_VDDR10_2 VSS_83
PCI_TRDYB/GPIO 3D_GPIO_2 AA25
VSS_84

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN POWER 2 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DSUB_R+ C320 0.1uF
INCM_R C321 0.1uF
R311
36 IC101
LGE35230(BCM35230KFSBG)
DSUB_G+ C327 0.1uF
C328 0.1uF NON_BCM_CAP
INCM_G B6
R317 VI_R
36 A6
VI_INCM_R
C7
VI_G
A7

DSUB_B+ C322 0.1uF B7

C8
VI_INCM_G
VI_B
BCM35230_with_CAP_220pF
INCM_B C323 0.1uF
VI_INCM_B
R312 IC101-*1
36 C13
DSUB_HSYNC HSYNC_IN
LGE35230
A13
DSUB_VSYNC VSYNC_IN
COMP1_Y
C9
COMP1_Pr C329
C330
0.1uF
0.1uF A9
VI_Y1 VIDEO INCM B6
BCM_CAP
A6
VI_R
COMP1_Pb VI_PR1
B9 VI_INCM_R
75 1%

75 1%
75 1%

C331 0.1uF C7
VI_PB1 VI_G
R331

R332
OPT
R330

B8
OPT

C332 0.1uF A7
VI_INCM_COMP1 VI_INCM_G
B7
Run Along DSUB_R Trace VI_B
C333 0.1uF C11 Near P801 INCM_R C8
OPT

VI_SC_R1 VI_INCM_B
C334 0.1uF A10
VI_SC_G1 Run Along DSUB_G Trace
C335 0.1uF B10 Near P801 INCM_G C13
VI_SC_B1 HSYNC_IN
C336 0.1uF C10 A13
VI_INCM_SC1 Run Along DSUB_B Trace VSYNC_IN
INCM_VID_COMP1 Near P801 INCM_B
R310 D10
0 SC_FB C9
VI_FB_1/GPIO Run Along COMP_Y_IN,COMP_Pr_IN,COMP_Pb_IN Trace VI_Y1
F13 Near JK1101 INCM_VID_COMP1 A9
VI_FS1 VI_PR1
B9
Run Along AV2_CVBS Trace VI_PB1
A12 Near JK1104 INCM_VID_AV2 B8
SC_R/COMP2_Pr VI_SC_R2 VI_INCM_COMP1
C12
SC_G/COMP2_Y VI_SC_G2 Run Along TUNER_CVBS_IF_P Trace
B12 Near TU2101/2
TU2201/2/3
INCM_TUNER C11
SC_B/COMP2_Pb VI_SC_B2 VI_SC_R1
B11 A10
75 1%

75 1%

VI_INCM_SC2
75 1%

Run Along AV1_CVBS Trace VI_SC_G1

Near JK1102 INCM_VID_AV1 B10
R334

R335

OPT
R333
OPT

E12 VI_SC_B1
JK1103 Run Along COMP_Y_IN,COMP_Pr_IN,COMP_Pb_IN/SC R,G,B Trace C10
VI_FB_2/GPIO Near INCM_VID_SC/COMP2 VI_INCM_SC1
E14 JK2501
VI_FS2
OPT

D10
E15 VI_FB_1/GPIO
F13
INCM_VID_SC/COMP2 VI_L1 VI_FS1
R318 F17
0 VI_C1_1
E16 A12
VI_INCM_LC1_1 VI_SC_R2
SC_CVBS_IN F14 C12
VI_C1_2 VI_SC_G2
INCM_VID_SC E11 B12
C303 0.1uF VI_INCM_LC1_2 VI_SC_B2
AV2_CVBS_IN B11
INCM_VID_AV2 C304 0.1uF C18 VI_INCM_SC2
NON_EU VI_CVBS1
R303 R325 0 B18
36 TU_CVBS C325 0.1uF E12
VI_INCM_CVBS1 VI_FB_2/GPIO
C326 0.1uF A18 E14
EU INCM_TUNER VI_CVBS2 VI_FS2
R306 R316 C19
R325-*1 VI_INCM_CVBS2
75 36 A19
10 1% E15
OPT VI_CVBS3 VI_L1
B19 F17
VI_INCM_CVBS3 VI_C1_1
C317 0.1uF C20 E16
AV1_CVBS_IN VI_CVBS4 VI_INCM_LC1_1
C318 0.1uF B20 F14
INCM_VID_AV1 VI_INCM_CVBS4 VI_C1_2
R304 +2.5V_BCM35230 E11
36 E19 VI_INCM_LC1_2
VI_SIF1_1
D19 C18
R313 VI_INCM_SIF1_1 VI_CVBS1
10K E10 B18
VI_SIF1_2 VI_INCM_CVBS1
C319 0.1uF F11 A18
TU_SIF VI_INCM_SIF1_2 VI_CVBS2
C19
R305 R314 +2.5V_BCM35230 VI_INCM_CVBS2
240 12K A19
OPT VI_CVBS3
B19
R319 VI_INCM_CVBS3
10K C20
OPT VI_CVBS4
B20
C324 0.1uF VI_INCM_CVBS4
INCM_SIF
R315 R320 E19
120 12K VI_SIF1_1
OPT OPT D19
VI_INCM_SIF1_1
E10
VI_SIF1_2
F11
VI_INCM_SIF1_2

IC101
LGE35230(BCM35230KFSBG)

NON_BCM_CAP
B15 AF8 R326 100
SPDIF_INC_P I2SSCK_OUTA/GPIO AUD_SCK
C15 AF9 R327 100
+3.3V_Normal SPDIF_INC_N I2SWS_OUTA/GPIO AUD_LRCK
AG9 R328 100
I2SSD_OUTA0/GPIO AUD_LRCH
C14 AC9 R329 100
SPDIF_IND_P I2SSOSCK_OUTA/GPIO AUD_MASTER_CLK
B14 AD8
SPDIF_IND_N I2SSD_OUTA1/GPIO TU_RESET_SUB C337 C338 C339 C340
R301 R302 AD9 22pF 22pF
I2SSD_OUTA2/GPIO 22pF 33pF
1.2K 1.2K G4
M_REMOTE_TX OPT OPT OPT OPT
I2SSCK_IN/GPIO
F4 E2
SCL3_3.3V I2SWS_IN I2SSCK_OUTC/GPIO HP_DET
G5 F2
SDA3_3.3V I2SSD_IN/GPIO I2SWS_OUTC/GPIO AV1_CVBS_DET
C301 C302 E3
I2SSD_OUTC/GPIO TU_RESET
33pF 33pF F3
50V 50V I2SSOSCK_OUTC/GPIO
C305 1uF 10V C25
PC_L_IN AADC_LINE_L1
C306 1uF 10V B24 G2
PC_R_IN AADC_LINE_R1 I2SSCK_OUTD/GPIO SC_RE1
C307 1uF 10V A24 G3
INCM_AUD_PC AADC_INCM1 I2SWS_OUTD/GPIO SC_RE2
I2SSD_OUTD/GPIO
G1
/RST_HUB AUDIO INCM
C308 1uF 10V E22 H1
PHONE JACK AV1_L_IN AADC_LINE_L2 I2SSOSCK_OUTD/GPIO S2_RESET
C309 1uF 10V E23
AV1_R_IN AADC_LINE_R2
C310 1uF 10V D23
INCM_AUD_AV1 AADC_INCM2
B13 Route Between AV1_L_IN & AV1_R_IN Trace
C24
SPDIF_OUTA/GPIO SPDIF_OUT Near JK1102 R321 0 INCM_AUD_AV1
AV2_L_IN C311 1uF 10V
AADC_LINE_L3
C312 1uF 10V C23 AG8 Route Between SC/COMP2_L_IN & SC/COMP2_R_IN Trace
AV2_R_IN AADC_LINE_R3 AUDMUTE_0/GPIO Near JK1103 R322 0
B23 E13 INCM_AUD_SC/COMP2
C313 1uF 10V JK2501
INCM_AUD_AV2 AADC_INCM3 AUDMUTE_1
R323 0 Route Between AV2_L_IN & AV2_R_IN Trace
E21 C28 Near JK1104 INCM_AUD_AV2
SC/COMP2_L_IN C314 1uF 10V HP_LOUT_N
AADC_LINE_L4 ADAC_AL_N
C315 1uF 10V D21 C27 Route Between PC_L_IN & PC_R_IN Trace
SC/COMP2_R_IN
D22
AADC_LINE_R4 ADAC_AL_P HP_LOUT_P Near JK801 R324 0 INCM_AUD_PC
INCM_AUD_SC/COMP2 C316 1uF 10V
AADC_INCM4
D28
ADAC_AR_N HP_ROUT_N
B22 D27
AADC_LINE_L5 ADAC_AR_P HP_ROUT_P
C22
AADC_LINE_R5
A22 C26
AADC_INCM5 ADAC_CL_N SCART1_Lout_N Near TU2101/2
TU2201/2/3
Route Along With TUNER_SIF_IF_N
INCM_SIF
A27
ADAC_CL_P SCART1_Lout_P
F21
AADC_LINE_L6
D20 B27
AADC_LINE_R6 ADAC_CR_N SCART1_Rout_N
E20 B28
AADC_INCM6 ADAC_CR_P SCART1_Rout_P

A21 B25
AADC_LINE_L7 ADAC_DL_N
C21 A25
AADC_LINE_R7 ADAC_DL_P
B21
AADC_INCM7
A26
ADAC_DR_N
B26
ADAC_DR_P

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN AUDIO/VIDEO 3 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DUAL COMPONENT

IC401,IC402 1ST : EAN61667501, 2ND : EAN61570701

IC401-*1
1ST : T-K4B2G1646B_HCK0, 2ND : T-H5TQ2G63BFR-PBC
IC402-*1
DDR STRAP
DDR_DQ[0]
DDR_DQ[1]
DDR_DQ[2]
DDR_DQ[3]
DDR_DQ[4]
+1.5V_DDR +1.5V_DDR
NFM18PS105R0J
NFM18PS105R0J
JEDEC Types : DDR_DQ[0:4] C410 C432
R401 R403 R405 R407 R409 6.3V 6.3V
4.7K 4.7K 4.7K 4.7K 4.7K 00001 : DDR3-1333H (CasL=9)
OPT 10101 : DDR3-1600K (CasL=11) (O) C403 C405 C407 C417 C421 C423 C425
DDR_1333 DDR_1333 IN OUT IN OUT
2.2uF 10uF 2.2uF 470pF 2.2uF 10uF 10uF
GND GND

DDR_DQ[10] +1.5V_DDR +1.5V_DDR

DDR_DQ[9] NFM18PS105R0J NFM18PS105R0J
DDR_DQ[7] C402 C433
+1.5V_DDR 6.3V 6.3V
DDR_DQ[8]
DDR_DQ[6] C412 C426
IN OUT 1uF IN OUT 1uF
DDR_DQ[5]
GND GND

R402 R432 R404 R406 R408 R410 C453 C454 C455

4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 1uF 1uF 1uF
OPT OPT OPT OPT OPT 6.3V
Bus Width : DDR_DQ[10] 6.3V 6.3V
0 - 16b
1 - 32b (O)
Chip Width : DDR_DQ[8]
0 - 8b
1 - 16b (O)
Chip Size : DDR_DQ[6:5]
00 - 4Gbit
01 - 2Gbit (O)
+1.5V_DDR
10 - 1Gbit +1.5V_DDR
11 - 512Mbit +1.5V_DDR
IC401 IC402
R422 R430
K4B2G1646C R416 K4B2G1646C 4.99K 4.7K
4.99K 1% OPT
1% R429
82
DDR_RESETb
N3 DDR_1333_SS M8 N3 DDR_1333_SS M8 R423
DDR_AA0 A0 VREFCA C415 R417 DDR_AA0 A0 VREFCA C435 4.99K C442
IC101 P7 4.99K P7 0.01uF 1% 100pF
DDR_AA1 A1 0.01uF 1% DDR_AA1 A1
LGE35230(BCM35230KFSBG) P3 P3
DDR_AA2 A2 DDR_AA2 A2 R428
N2 H1 N2 H1 82
DDR_DQ[0-7] NON_BCM_CAP DDR_AA3 A3 VREFDQ DDR_VREFA DDR_AA3 A3 VREFDQ C436 DDR_VREFA
P8 C416 P8 DDR_CKE
DDR01_AA4 A4 0.01uF DDR23_AA4 A4 0.01uF C437 R431
DDR_DQ[0] U26 V23 P2 P2 4.7K
DDR_DQA_0 DDR_ADA_0 DDR_AA0 DDR01_AA5 A5 DDR23_AA5 A5 100pF
R26 AB27 R8 L8 OPT
DDR_DQ[1] DDR_DQA_1 DDR_AA1 R8 L8 R415 240 DDR23_AA6 R421 240
DDR_ADA_1 DDR01_AA6 A6 ZQ A6 ZQ
DDR_DQ[2] U27 Y23 R2 R2 1% +1.5V_DDR
DDR_DQA_2 DDR_ADA_2 DDR_AA2 DDR_AA7 A7 1% +1.5V_DDR DDR_AA7 A7
DDR_DQ[3] R27 Y26 T8 T8
DDR_DQA_3 DDR_ADA_3 DDR_AA3 DDR_AA8 A8 DDR_AA8 A8
DDR_DQ[4] V27 R3 B2 R3 B2
DDR_DQA_4 DDR_AA9 A9 VDD_1 DDR_AA9 A9 VDD_1 DDR_AA13 R424 56
DDR_DQ[5] P26 AB26 L7 D9 L7 D9
DDR_DQA_5 DDR_ADA_4 DDR01_AA4 DDR_AA10 A10/AP VDD_2 DDR_AA10 A10/AP VDD_2 DDR_AA14 R425 56 OPT
DDR_DQ[6] U25 Y24 R7 G7 R7 G7
DDR_DQ[8-15] DDR_DQA_6 DDR_ADA_5 DDR01_AA5 DDR_AA11 A11 VDD_3 C438 1uF
P27 AC26 DDR_AA11 A11 VDD_3 N7 K2
DDR_DQ[7] DDR01_AA6 N7 K2 DDR_AA12 AR401 56
DDR_DQA_7 DDR_ADA_6 DDR_AA12 A12/BC VDD_4 A12/BC VDD_4 DDR_AA2
DDR_DQ[8] R24 T3 K8 T3 K8
DDR_DQA_8 DDR_AA13 A13 VDD_5 C404 0.1uF
N24 AB24 DDR_AA13 A13 VDD_5 N1 DDR_AA11
DDR_DQ[9] DDR23_AA4 N1
DDR_DQA_9 DDR_ADA_ALT_4 VDD_6 VDD_6 DDR_AA3
DDR_DQ[10] T25 AC25 M7 N9 M7 N9
DDR_DQA_10 DDR_ADA_ALT_5 DDR23_AA5 NC_5 VDD_7 DDR_AA7 C406 0.1uF
M23 AC24 NC_5 VDD_7 R1
DDR_DQ[11] DDR23_AA6 R1 AR402 56
DDR_DQA_11 DDR_ADA_ALT_6 VDD_8 VDD_8
DDR_DQ[12] R23 M2 R9 M2 R9
DDR_DQA_12 DDR_BAA0 BA0 VDD_9 DDR_BAA0 BA0 VDD_9 DDR_AA9
DDR_DQ[13] N25 AB25 N8 N8 C450 0.1uF
DDR_DQA_13 DDR_ADA_7 DDR_AA7 DDR_BAA1 BA1 DDR_BAA1 BA1 DDR_AA8
DDR_DQ[14] T24 AD28 M3 M3
DDR_DQ[16-23] DDR_DQA_14 DDR_ADA_8 DDR_AA8 DDR_BAA2 BA2 C408 0.1uF
N26 Y25 DDR_BAA2 BA2 A1 DDR_AA0
DDR_DQ[15] DDR_AA9 A1 AR403 56
DDR_DQA_15 DDR_ADA_9 VDDQ_1 VDDQ_1 DDR_AA1
DDR_DQ[16] L26 AA27 J7 A8 J7 A8 C439
DDR_DQA_16 DDR_ADA_10 DDR_AA10 DDR01_CLK DDR23_CLK CK VDDQ_2 DDR_BAA0 1uF
H27 AC27 CK VDDQ_2 K7 C1
DDR_DQ[17] DDR_AA11 K7 C1 DDR23_CLKb
DDR_DQA_17 DDR_ADA_11 DDR01_CLKb CK VDDQ_3 CK VDDQ_3 DDR_BAA2
DDR_DQ[18] L27 AA26 K9 C9 K9 C9
DDR_DQA_18 DDR_ADA_12 DDR_AA12 DDR_CKE R418 R419 DDR_CKE CKE VDDQ_4 DDR_BAA1 C409 0.1uF
J26 AA24 R412 R413 CKE VDDQ_4 D2
DDR_DQ[19] DDR_AA13 56 56 D2 56 56 AR404 56
DDR_DQA_19 DDR_ADA_13 VDDQ_5 1% 1% VDDQ_5 DDR_AA10
DDR_DQ[20] M27 AD27 1% 1% +1.5V_DDR L2 E9 +1.5V_DDR L2 E9 C451 0.1uF
DDR_DQA_20 DDR_ADA_14 DDR_AA14 CS VDDQ_6 CS VDDQ_6 DDR_AA12
DDR_DQ[21] G27 K1 F1 R420 10K K1 F1
DDR_DQA_21 C401 R414 10K ODT VDDQ_7 C419 ODT VDDQ_7 DDR_WEb
DDR_DQ[22] M26 Y27 J3 H2 1000pF J3 H2
DDR_DQ[24-31] DDR_DQA_22 DDR_BAA_0 DDR_BAA0 1000pF DDR_RASb RAS VDDQ_8 C411 0.1uF
H26 AB28 DDR_RASb RAS VDDQ_8 K3 H9
DDR_DQ[23] DDR_BAA1 K3 H9 DDR_CASb AR405 56
DDR_DQA_23 DDR_BAA_1 DDR_CASb CAS VDDQ_9 CAS VDDQ_9 DDR23_AA6
DDR_DQ[24] L23 W24 L3 L3 C440
DDR_DQA_24 DDR_BAA_2 DDR_BAA2 DDR_WEb DDR_WEb WE DDR23_AA4 1uF
H25 WE J1
DDR_DQ[25] J1
DDR_DQA_25 NC_1 NC_1 DDR23_AA5
DDR_DQ[26] L24 V24 T2 J9 T2 J9
DDR_DQA_26 DDR_RASA_N DDR_RASb DDR_RESETb RESET NC_2 DDR_RESETb RESET NC_2
DDR_DQ[27] J24 W25 L1 L1 AR406 56 C452 0.1uF
DDR_DQA_27 DDR_CASA_N DDR_CASb NC_3 NC_3 DDR01_AA6
DDR_DQ[28] M24 V26 L9 L9
DDR_DQA_28 DDR_WEA_N DDR_WEb NC_4 NC_4 DDR01_AA4
DDR_DQ[29] H23 F3 T7 F3 T7
DDR_DQA_29 DDR_QS0 DQSL NC_6 DDR_AA14 DDR_QS2 DQSL NC_6 DDR_AA14 DDR01_AA5
DDR_DQ[30] L25 U24 G3 G3
DDR_DQA_30 DDR_CKEA DDR_CKE DDR_QS0b DQSL DDR_QS2b DQSL R426 56
DDR_DQ[31] H24 DDR_CASb
DDR_DQA_31 R427 56 C441 1uF
W27 C7 A9 C7 A9 DDR_RASb
DDR_DM[0-3] DDR_CKA01_P DDR01_CLK DDR_QS1 DQSU VSS_1 DDR_QS3 DQSU VSS_1
W28 B7 B3 B7 B3
DDR_CKA01_N DDR01_CLKb DDR_QS1b DQSU VSS_2 DDR_QS3b DQSU VSS_2
DDR_DM[0] T26 E1 E1
DDR_DMA_0 VSS_3 VSS_3
DDR_DM[1] P25 N28 E7 G8 E7 G8
DDR_DMA_1 DDR_CKA23_P DDR23_CLK DDR_DM[0] DML VSS_4 DDR_DM[2] DML VSS_4
DDR_DM[2] J27 N27 D3 J2 D3 J2
DDR_DMA_2 DDR_CKA23_N DDR23_CLKb DDR_DQ[0-7] DDR_DM[1] DMU VSS_5 DDR_DQ[16-23] DDR_DM[3] DMU VSS_5
DDR_DM[3] K24 J8 J8
DDR_DMA_3 VSS_6 VSS_6
U23 E3 M1 DDR_DQ[16] E3 M1
DDR_VREFA DDR_VREFA DDR_DQ[0] DQL0 DQL0 VSS_7
VSS_7 F7 M9
DDR_DQ[1] F7 M9 DDR_DQ[17] DQL1
DQL1 VSS_8 VSS_8
T27 AA23 F2 P1 DDR_DQ[18] F2 P1
DDR_QS0 DDR_DQSA_P_0 DDR_RST_N DDR_RESETb DDR_DQ[2] DQL2 VSS_9
T28 DQL2 VSS_9 F8 P9
DDR_QS0b DDR_DQ[3] F8 P9 DDR_DQ[19]
DQL3
DDR_DQSA_N_0 DQL3 VSS_10 VSS_10
W26 R411 240 H3 T1 DDR_DQ[20] H3 T1 IC401-*1 IC402-*1
DDR_ZQ DDR_DQ[4] DQL4 VSS_11 K4B2G1646C-HCK0
P24 DQL4 VSS_11 H8 T9 K4B2G1646C-HCK0
DDR_QS1 1% DDR_DQ[5] H8 T9 DDR_DQ[21]
DQL5
DDR_DQSA_P_1 DQL5 VSS_12 VSS_12 DDR_1600_SS
P23 G2 DDR_DQ[22] G2 N3 DDR_1600_SS M8
N3
A0 VREFCA
M8
DDR_QS1b DDR_DQSA_N_1 DDR_DQ[6] DQL6 A0 VREFCA P7
DQL6 H7 P7
A1 P3
A1

DDR_DQ[7] H7 DDR_DQ[24-31] DDR_DQ[23]

DQL7
P3
A2 N2
A2
H1
K27 DDR_DQ[8-15] DQL7 B1 N2
A3 VREFDQ
H1
P8
A3 VREFDQ

DDR_QS2 DDR_DQSA_P_2 B1 VSSQ_1

P8
A4 P2
A4

K28 VSSQ_1 D7 B9 P2
A5 R8
A5
L8
DDR_QS2b DDR_DQ[8] D7 B9 DDR_DQ[24]
DQU0
R8 L8 A6 ZQ
DDR_DQSA_N_2 DQU0 VSSQ_2 VSSQ_2 R2
A6 ZQ R2
A7
C3 D1 DDR_DQ[30] C3 D1 T8
A7 T8
A8
DDR_DQ[14] DQU1 VSSQ_3 A8 R3 B2
K25 DQU1 VSSQ_3 C8 D8 R3
A9 VDD_1
B2
L7
A9 VDD_1
D9
DDR_QS3 DDR_DQ[13] C8 D8 DDR_DQ[29]
DQU2
L7 D9 A10/AP VDD_2
DDR_DQSA_P_3 DQU2 VSSQ_4 VSSQ_4 R7
A10/AP VDD_2
G7
R7
A11 VDD_3
G7
K26 C2 E2 DDR_DQ[28] C2 E2 N7
A11 VDD_3
K2
N7
A12/BC VDD_4
K2
DDR_QS3b DDR_DQSA_N_3 DDR_DQ[12] DQU3 VSSQ_5 A12/BC VDD_4 T3 K8
DQU3 VSSQ_5 A7 E8 T3
A13 VDD_5
K8 A13 VDD_5
N1
DDR_DQ[9] A7 E8 DDR_DQ[25]
DQU4
N1 VDD_6
DQU4 VSSQ_6 VSSQ_6 M7
VDD_6
N9
M7
NC_5 VDD_7
N9

A2 F9 DDR_DQ[26] A2 F9 NC_5 VDD_7

R1 VDD_8
R1
DDR_DQ[10] DQU5 VSSQ_7 VDD_8 M2 R9
DQU5 VSSQ_7 B8 G1 M2
BA0 VDD_9
R9
N8
BA0 VDD_9

DDR_DQ[15] B8 G1 DDR_DQ[31]
DQU6
N8 BA1
IC401-*2 IC401-*3 DQU6 VSSQ_8 VSSQ_8 M3
BA1 M3
BA2
IC402-*2 IC402-*3 A3 G9 DDR_DQ[27] A3 G9 BA2 A1
NT5CB128M16BP-CG NT5CB128M16BP-CG NT5CB128M16BP-DI NT5CB128M16BP-DI DDR_DQ[11] DQU7 VSSQ_9 VDDQ_1
A1
J7
VDDQ_1
A8
DQU7 VSSQ_9 J7
CK VDDQ_2
A8
K7
CK VDDQ_2
C1
K7 C1 CK VDDQ_3
DDR_1333_NANYA DDR_1333_NANYA DDR_1600_NANYA CK VDDQ_3 K9 C9
N3 M8 N3 M8 DDR_1600_NANYA K9 C9 CKE VDDQ_4
N3 M8 N3 M8 CKE VDDQ_4 D2
A0 VREFCA A0 VREFCA A0 VREFCA D2 VDDQ_5
P7 P7 P7 A0 VREFCA L2 E9
A1 A1 P7 VDDQ_5
P3 A1 P3 A1 L2 E9 CS VDDQ_6
P3 P3 CS VDDQ_6 K1 F1
A2 A2 A2 K1 F1 ODT VDDQ_7
N2 H1 N2 H1 N2 H1 A2 J3 H2
A3 VREFDQ A3 VREFDQ N2 H1 ODT VDDQ_7
P8 A3 VREFDQ P8 A3 VREFDQ J3 H2 RAS VDDQ_8
P8 P8 RAS VDDQ_8 K3 H9
A4 A4 A4 K3 H9 CAS VDDQ_9
P2 P2 P2 A4 L3
A5 A5 P2 CAS VDDQ_9
R8 L8 A5 R8 L8 A5 L3 WE
R8 L8 R8 L8 WE J1
A6 ZQ A6 ZQ A6 ZQ J1 NC_1
R2 R2 R2 A6 ZQ T2 J9
A7 A7 R2 NC_1
T8 A7 T8 A7 T2 J9 RESET NC_2
T8 T8 RESET NC_2 L1
A8 A8 A8 L1 NC_3
R3 B2 R3 B2 R3 B2 A8 L9
A9 VDD_1 A9 VDD_1 R3 B2 NC_3
L7 D9 A9 VDD_1 L7 D9 A9 VDD_1 L9 NC_4
L7 D9 L7 D9 NC_4 F3 T7
A10/AP VDD_2 A10/AP VDD_2 A10/AP VDD_2 F3 T7 DQSL NC_6
R7 G7 R7 G7 R7 G7 A10/AP VDD_2 G3
A11 VDD_3 A11 VDD_3 R7 G7 DQSL NC_6
N7 K2 A11 VDD_3 N7 K2 A11 VDD_3 G3 DQSL
N7 K2 N7 K2 DQSL
A12 VDD_4 A12 VDD_4 A12 VDD_4
T3 K8 T3 K8 T3 K8 A12 VDD_4 C7 A9
NC_6 VDD_5 NC_6 VDD_5 T3 K8
N1 NC_6 VDD_5 N1 NC_6 VDD_5 C7 A9 DQSU VSS_1
N1 N1 DQSU VSS_1 B7 B3
VDD_6 VDD_6 VDD_6 B7 B3 DQSU VSS_2
M7 N9 M7 N9 M7 N9 VDD_6 E1
NC_5 VDD_7 NC_5 VDD_7 M7 N9 DQSU VSS_2
R1 NC_5 VDD_7 R1 NC_5 VDD_7 E1 VSS_3
R1 R1 VSS_3 E7 G8
VDD_8 VDD_8 VDD_8 E7 G8 DML VSS_4
M2 R9 M2 R9 M2 R9 VDD_8 D3 J2
BA0 VDD_9 BA0 VDD_9 M2 R9 DML VSS_4
N8 BA0 VDD_9 N8 BA0 VDD_9 D3 J2 DMU VSS_5
N8 N8 DMU VSS_5 J8
BA1 BA1 BA1 J8 VSS_6
M3 M3 M3 BA1 E3 M1
BA2 BA2 M3 VSS_6
A1 BA2 A1 BA2 E3 M1 DQL0 VSS_7
A1 A1 DQL0 VSS_7 F7 M9
VDDQ_1 VDDQ_1 VDDQ_1 F7 M9 DQL1 VSS_8
J7 A8 J7 A8 J7 A8 VDDQ_1 F2 P1
CK VDDQ_2 CK VDDQ_2 J7 A8 DQL1 VSS_8
K7 C1 CK VDDQ_2 K7 C1 CK VDDQ_2 F2 P1 DQL2 VSS_9
K7 C1 K7 C1 DQL2 VSS_9 F8 P9
CK VDDQ_3 CK VDDQ_3 CK VDDQ_3 F8 P9 DQL3 VSS_10
K9 C9 K9 C9 K9 C9 CK VDDQ_3 H3 T1
CKE VDDQ_4 CKE VDDQ_4 K9 C9 DQL3 VSS_10
D2 CKE VDDQ_4 D2 CKE VDDQ_4 H3 T1 DQL4 VSS_11
D2 D2 DQL4 VSS_11 H8 T9
VDDQ_5 VDDQ_5 VDDQ_5 H8 T9 DQL5 VSS_12
L2 E9 L2 E9 L2 E9 VDDQ_5 G2
CS VDDQ_6 CS VDDQ_6 L2 E9 DQL5 VSS_12
K1 F1 CS VDDQ_6 K1 F1 CS VDDQ_6 G2 DQL6
K1 F1 K1 F1 DQL6 H7
ODT VDDQ_7 ODT VDDQ_7 ODT VDDQ_7 H7 DQL7
J3 H2 J3 H2 J3 H2 ODT VDDQ_7 B1
RAS VDDQ_8 RAS VDDQ_8 J3 H2 DQL7
K3 H9 RAS VDDQ_8 K3 H9 RAS VDDQ_8 B1 VSSQ_1
K3 H9 K3 H9 VSSQ_1 D7 B9
CAS VDDQ_9 CAS VDDQ_9 CAS VDDQ_9 D7 B9 DQU0 VSSQ_2
L3 L3 L3 CAS VDDQ_9 C3 D1
WE WE L3 DQU0 VSSQ_2
J1 WE J1 WE C3 D1 DQU1 VSSQ_3
J1 J1 DQU1 VSSQ_3 C8 D8
NC_1 NC_1 NC_1 C8 D8 DQU2 VSSQ_4
T2 J9 T2 J9 T2 J9 NC_1 C2 E2
RESET NC_2 RESET NC_2 T2 J9 DQU2 VSSQ_4
L1 RESET NC_2 L1 RESET NC_2 C2 E2 DQU3 VSSQ_5
L1 L1 DQU3 VSSQ_5 A7 E8
NC_3 NC_3 NC_3 A7 E8 DQU4 VSSQ_6
L9 L9 L9 NC_3 A2 F9
NC_4 NC_4 L9 DQU4 VSSQ_6
F3 T7 NC_4 F3 T7 NC_4 A2 F9 DQU5 VSSQ_7
F3 T7 F3 T7 DQU5 VSSQ_7 B8 G1
DQSL NC_7 DQSL NC_7 DQSL NC_7 B8 G1 DQU6 VSSQ_8
G3 G3 G3 DQSL NC_7 A3 G9
DQSL DQSL G3 DQU6 VSSQ_8
DQSL DQSL A3 G9 DQU7 VSSQ_9
DQU7 VSSQ_9
C7 A9 C7 A9 C7 A9
DQSU VSS_1 DQSU VSS_1 C7 A9
B7 B3 DQSU VSS_1 B7 B3 DQSU VSS_1
B7 B3 B7 B3
DQSU VSS_2 DQSU VSS_2 DQSU VSS_2
E1 E1 E1 DQSU VSS_2
VSS_3 VSS_3 E1
E7 G8 VSS_3 E7 G8 VSS_3
E7 G8 E7 G8
DML VSS_4 DML VSS_4 DML VSS_4
D3 J2 D3 J2 D3 J2 DML VSS_4
DMU VSS_5 DMU VSS_5 D3 J2
J8 DMU VSS_5 J8 DMU VSS_5
J8 J8
VSS_6 VSS_6 VSS_6
E3 M1 E3 M1 E3 M1 VSS_6
DQL0 VSS_7 DQL0 VSS_7 E3 M1
F7 M9 DQL0 VSS_7 F7 M9 DQL0 VSS_7
F7 M9 F7 M9
DQL1 VSS_8 DQL1 VSS_8 DQL1 VSS_8
F2 P1 F2 P1 F2 P1 DQL1 VSS_8
DQL2 VSS_9 DQL2 VSS_9 F2 P1
F8 P9 DQL2 VSS_9 F8 P9 DQL2 VSS_9
F8 P9 F8 P9
DQL3 VSS_10 DQL3 VSS_10 DQL3 VSS_10
H3 T1 H3 T1 H3 T1 DQL3 VSS_10
DQL4 VSS_11 DQL4 VSS_11 H3 T1
H8 T9 DQL4 VSS_11 H8 T9 DQL4 VSS_11
H8 T9 H8 T9
DQL5 VSS_12 DQL5 VSS_12 DQL5 VSS_12
G2 G2 G2 DQL5 VSS_12
DQL6 DQL6 G2
H7 DQL6 H7 DQL6
H7 H7
DQL7 DQL7 DQL7
B1 B1 B1 DQL7
VSSQ_1 VSSQ_1 B1
D7 B9 VSSQ_1 D7 B9 VSSQ_1
D7 B9 D7 B9
DQU0 VSSQ_2 DQU0 VSSQ_2 DQU0 VSSQ_2
C3 D1 C3 D1 C3 D1 DQU0 VSSQ_2
DQU1 VSSQ_3 DQU1 VSSQ_3 C3 D1
C8 D8 DQU1 VSSQ_3 C8 D8 DQU1 VSSQ_3
C8 D8 C8 D8
DQU2 VSSQ_4 DQU2 VSSQ_4 DQU2 VSSQ_4
C2 E2 C2 E2 C2 E2 DQU2 VSSQ_4
DQU3 VSSQ_5 DQU3 VSSQ_5 C2 E2
A7 E8 DQU3 VSSQ_5 A7 E8 DQU3 VSSQ_5
A7 E8 A7 E8
DQU4 VSSQ_6 DQU4 VSSQ_6 DQU4 VSSQ_6
A2 F9 A2 F9 A2 F9 DQU4 VSSQ_6
DQU5 VSSQ_7 DQU5 VSSQ_7 A2 F9
B8 G1 DQU5 VSSQ_7 B8 G1 DQU5 VSSQ_7
B8 G1 B8 G1
DQU6 VSSQ_8 DQU6 VSSQ_8 DQU6 VSSQ_8
A3 G9 A3 G9 A3 G9 DQU6 VSSQ_8
DQU7 VSSQ_9 DQU7 VSSQ_9 A3 G9
DQU7 VSSQ_9 DQU7 VSSQ_9

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN DDR 4 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 NEC MICOM

FLMD0
GND

+3.5V_ST

10K
47K
C602 C603 R641
50V 50V MICOM_DOWNLOAD

OPT

R639
13pF 13pF 0

R637
X601

For Debug 10MHz

15pF

15pF

WIRELESS_PWR_EN
DEBUG_MICOM

C606

C607
P601 +3.5V_ST

WIRELESS_DET
12505WS-12A00

MICOM_RESET
1 X602
+3.5V_ST

2
MICOM_RESET 32.768KHz
3 R615 22
NEC_ISP_Tx R642 +3.5V_ST
10Mhz Crystal
4 4.7M
R617 22 OPT
5 NEC_ISP_Rx

47K
6

7
OCD1A
8
DEBUG_MICOM_RESET

P122/X2/EXCLK/OCD0B

R644
9
OCD1B GND SW1
+3.5V_ST
10
JTP-1127WEM
2 1

22

P120/INTP0/EXLVI
R621 22

270K
11
FLMD0

OPT
C608

R645
P124/XT2/EXCLKS
0.1uF

0.1uF
12
4 3
R606 10K 16V

P121/X1/OCD0A
13

R643
C604
0.1uF

C605

P123/XT1
R607 10K +3.5V_ST R647 20K
NEC_ISP_Rx
R610 10K 1/16W

FLMD0

RESET
NEC_ISP_Tx 1%

REGC

1/16W
R646
VDD
VSS

P40
P41

20K

1%
R626 4.7K

R628 4.7K

48
47
46
45
44
43
42
41
40
39
38
37
R629 22
P60/SCL0 1 36 P140/PCL/INTP6 RL_ON
SCL2_3.3V

R630 22
P61/SDA0 2 35 P00/TI000
SDA2_3.3V SCART_MUTE
P62/EXSCL0 3 34 P01/TI010/TO00 R648 10K C
EDID_WP

EEPROM for Micom EEPROM_SCL

P63 P130 B Q601

4 33 2SC3052
EEPROM_SDA
P33/TI51/TO51/INTP4 IC602 P20/ANI0 E
+3.5V_ST HDMI_CEC
R631 22
5 32 R649 0

OPT
P75 6 uPD78F0514 31 ANI1/P21
POWER_ON/OFF2_1 MODEL1_OPT_3
IC601 P74 ANI2/P22
M24C16-WMN6T AMP_MUTE 7 30 MODEL1_OPT_2
P73/KR3 NEC_MICOM ANI3/P23
MODEL1_OPT_0 8 29 POWER_ON/OFF1
NC/E0 VCC
1 8 R632 22 P72/KR2 9 28 ANI4/P24
R601

SOC_RESET MICOM_DOWNLOAD
47K

NC/E1
2 7
WC P71/KR1 10 27 ANI5/P25
INV_CTL SIDE_HP_MUTE

NC/E2 SCL R619

P70/KR0 11 26 ANI6/P26
3 6 EEPROM_SCL MODEL1_OPT_1 KEY2
R633
22
22 P32/INTP3/OCD1B 12 25 ANI7/P27
VSS SDA R616 OCD1B KEY1
4 5 EEPROM_SDA OPT
22

13
14
15
16
17
18
19
20
21
22
23
24
S/T_SCL

R627
4.7K

P31/INTP2/OCD1A
P30/INTP1
P17/TI50/TO50
P16/TOH1/INTP5
P15/TOH0
P14/RXD6
P13/TXD6
P12/SO10
P11/SL10/RXD0
P10/SCK10/TXD0
AVREF
AVSS
+3.5V_ST

+3.5V_ST

MODEL OPTION

PIN NAME

C609 1uF
PIN NO. HIGH LOW
MICOM MODEL OPTION MODEL_OPT_0 8
10YEAR_TOOL
(10 SENSOR)
11YEAR_TOOL
(11 SENSOR)

MODEL_OPT_1 11 I2C_LED PWM_LED

+3.5V_ST
MODEL_OPT_2 30 TOUCH_KEY TACT_KEY

MODEL_OPT_3
10K

10K

10K

10K

31 PDP/3D LCD/OLED
10YEAR_TOOL
TOUCH_KEY

I2C LED
PDP/3D

OPT
R611

R613

R622

R624

LCD PDP OLED 3D

R604 100
AMP_RESET_N

10K
MODEL1_OPT_0 MODEL_OPT_3
22

R605 100 0 1 0 1 +3.5V_ST

PANEL_CTL MODEL1_OPT_1
R602 100
INSTANT_MODE MODEL1_OPT_2
R603 100
MODEL1_OPT_3
R638

R640

LOW LOW_SMALL TBD HIGH

10K

10K

10K

10K
11YEAR_TOOL

R636
LCD/OLED

TACT_KEY

PWM_LED

4.7K
MODEL_OPT_1 0 0 1 1
R612

R614

R623

R625

MODEL_OPT_2 0 1 0 1
LED_R/BUZZ
LED_B/LG_LOGO
POWER_DET

IR

NEC_ISP_Tx

NEC_TXD
NEC_ISP_Rx

POWER_ON/OFF2_2

NEC_RXD
OCD1A
S/T_SDA

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MICOM 6 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 [Local Dimming Block]

P1601
12507WR-08L

3 L/DIM0_SCLK

5 L/DIM0_MOSI

6 R1601 33
SCL2_3.3V
LPB_42/47/55

7 R1602 33
SDA2_3.3V
LPB_42/47/55

8 L/DIM0_VS

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR 16 50
L_DIMMING
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DUAL COMPONENT

Q1901 1ST : 0TRIY80001A 2ND : 0TR387500AA

Q1902 1ST : EBK60752501, 2ND : EBK61011501

IC1904 1ST : 0ISTLPH062A, 2ND : EAN40055001

PCM_MDI[0-7] CI_MDI[0-7]
Close to BCM35230
PCM_MDI[0] R1909 22 OPT CI_MDI[0]
R1910 CI_MDI[1]
PCM_MDI[1] 22 OPT

BCM INT Demod PCM_MDI[2] AR1903 22 OPT CI_MDI[2]

PCM_MDI[3] CI_MDI[3] +5V_CI_ON
PCM_MDI[4] CI_MDI[4]
CI_MDI[5]
PCM_MDI[5]
R1915 22 OPT CI_MDI[6]
PCM_MDI[6]
R1916 22 OPT CI_MDI[7] C1904 C1905
PCM_MDI[7] R1932 R1933 CI_DATA[0-7]
0.1uF 10uF
10V 10K 10K
CI P1901
FE_TS_DATA[0-7] CI CI OPT
10067972-000LF CI R1946
10K
FE_TS_DATA[0] GND GND /PCM_CE1
R1901 22 CI 35 1 OPT
FE_TS_DATA[1] +5V_CI_ON R1937 62 /CI_DET1 36 2 DAT3 CI_DATA[3]
R1902 22 CI /CI_CD1
CI TS_OUT3 37 3 DAT4 CI_DATA[4]
FE_TS_DATA[2] CI_TS_DATA[3]
R1903 22 CI TS_OUT4 DAT5 CI_DATA[5]
CI_TS_DATA[4] 38 4
FE_TS_DATA[3] TS_OUT5 DAT6 +5V_CI_ON
R1904 22 CI R1971 R1972 39 5 CI_DATA[6]
CI_TS_DATA[5]
FE_TS_DATA[4] 10K 10K TS_OUT6 40 6 DAT6 CI_DATA[7]
R1905 22 CI CI_TS_DATA[6]
CI CI TS_OUT7 /CARD_EN1 CI R1956 22 R1973
FE_TS_DATA[5] 22 CI CI_TS_DATA[7] 41 7
R1906 10K
R1976 22 CI CARD_EN2 42 8 ADDR10 CI R1962 22 CI_ADDR[10]
FE_TS_DATA[6] R1907 22 CI /PCM_IORD CI_ADDR[10] CI
R1974 22 CI VS1 43 9 /O_EN CI R1963 22
FE_TS_DATA[7] /PCM_IOWR /PCM_OE
R1908 22 CI IORD 44 10 ADDR11 CI R1957 22 PCM_ADDR[11]
PCM_ADDR[11] +5V_CI_ON
CI_MDI[0-7] IOWR 45 11 ADDR10 CI R1958 22 PCM_ADDR[9]
PCM_ADDR[9]
TS_IN_SYN 46 12 ADDR8 CI R1959 22 CI_ADDR[8]
BCM INT Demod Close to BCM35230 22
CI_ADDR[8]
R1968 R1975
CI_MDI[0] TS_IN0 47 13 ADDR13 CI R1960 PCM_ADDR[13]
R1917 22 OPT PCM_ADDR[13] 10K 10K
PCM_MISTRT CI_MISTRT CI_MDI[1] TS_IN1 ADDR14 CI R1961 22 CI_ADDR[14]
48 14 CI_ADDR[14] CI CI CI
R1918 22 OPT CI_MDI[2] TS_IN2 R1964 22
PCM_MIVAL_ERR CI_MIVAL_ERR 49 15 /WR_EN
/PCM_WE
PCM_MCLKI R1919 22 OPT CI_MDI[3] TS_IN3 50 16 /IRQA R1967 22 CI
CI_MCLKI /PCM_IRQA
VCC 51 17 VCC C1910 0.1uF C1913
CI
0 VPP R1944 0 CI 0.1uF
R1977 +5V_CI_ON R1936 52 18 VPP 16V
Close to Tuner CI_MDI[4] OPT TS_IN4 OPT
10K 53 19 TS_IN_VAL
R1920 22 CI OPT CI_MDI[5] TS_IN5 54 20 TS_IN_CLK
NIM_TS_SYNC
CI_MDI[6] TS_IN6 ADDR12 CI R1947 22 PCM_ADDR[12]
R1921 22 CI R1929 R1930 55 21 PCM_ADDR[12]
NIM_VAL_ERR CI R1948
10K 10K CI_MDI[7] TS_IN7 56 22 ADDR7 22 PCM_ADDR[7]
R1922 22 CI PCM_ADDR[7]
NIM_TS_CLK OPT OPT TS_OUT_CLK ADDR6 CI R1949 22 CI_ADDR[6]
CI_TS_CLK 57 23 CI_ADDR[6]
R1927 22 CI CI_RESET ADDR5 CI R1950 22 CI_ADDR[5]
PCM_RST 58 24 CI_ADDR[5]
R1928 22 CI CI_WAIT ADDR4 CI R1951 22 PCM_ADDR[4]
/PCM_WAIT 59 25 PCM_ADDR[4]
R1934 10K OPT INPACK ADDR3 CI R1952 22 PCM_ADDR[3]
60 26 PCM_ADDR[3]
REG CI R1953 22
CI TS INPUT R1935 0 CI 61 27 ADDR2 PCM_ADDR[2]
PCM_ADDR[2]
TS_OUT_VAL ADDR1 CI R1954 22 CI_ADDR[1]
CI_TS_VAL 62 28 CI_ADDR[1]
TS_OUT_SYN ADDR0 CI R1955 22 CI_ADDR[0]
CI_TS_SYNC 63 29 CI_ADDR[0]
TS_OUT0 64 30 DAT0 CI_DATA[0]
CI_TS_DATA[0]
TS_OUT1 65 31 DAT1 CI_DATA[1] +5V_CI_ON
CI_TS_DATA[1]
TS_OUT2 66 32 DAT2 CI_DATA[2]
CI_TS_DATA[2]
PCM_TS_DATA[0-7] Close to CI Slot CI_TS_DATA[0-7]
/CI_CD2 R1938 CI 62 /CI_DET2 67 33 /IO_BIT R1945 10K
PCM_TS_DATA[0] AR1901 100 CI GND 68 34 GND OPT
CI_TS_DATA[0]
PCM_TS_DATA[1]
CI_TS_DATA[1] G2 69 G1
PCM_TS_DATA[2]
CI_TS_DATA[2]
PCM_TS_DATA[3]
CI_TS_DATA[3]

PCM_TS_DATA[4] AR1902 100 CI CI_TS_DATA[4]

PCM_TS_DATA[5] CI_TS_DATA[5] CI_MIVAL_ERR
PCM_TS_DATA[6] CI_TS_DATA[6] CI_MCLKI
PCM_TS_DATA[7] CI_MISTRT
CI_TS_DATA[7]

Close to CI Slot
R1923 220 CI
PCM_TS_CLK CI_TS_CLK
R1924 100 CI
PCM_TS_VAL CI_TS_VAL
R1925 100 CI CI POWER ENABLE CONTROL
PCM_TS_SYNC CI_TS_SYNC OE DIR CI_DATA NAND_DATA +3.3V_CI
C1916
12pF L L OUTPUT INPUT +5V_CI_ON
+5V_Normal
50V L H INPUT OUTPUT Q1902 L1902
OPT H X Z Z 0.1uF AO3407A BLM18PG121SN1D
CI TS OUTPUT OPT C1903

D
CI
16V
IC1903 R1931 22 CI C1906 CI CI
NAND_REb R1969
R1926 22 CI 74LVC245A OPT 0.1uF C1912 CI C1914 10K
/CI_EN1

G
NAND_DATA[0-7] 16V 0.1uF
R1943 C1909 0.1uF CI
VCC
20 1
DIR CI 16V
CI 22K 4.7uF 16V
CI_DATA[0-7] R1940
OE
19 2
A0 NAND_DATA[0] 16V
AR1904 100 CI 10K OPT
CI_DATA[0] B0
18 3
A1 NAND_DATA[1] OPT
CI_DATA[1]
B1
17 4
A2 NAND_DATA[2]
CI_DATA[2]
B2 A3 NAND_DATA[3] R1987
16 5
2.2K
B3
15 6
A4 NAND_DATA[4] CI
CI_DATA[3] R1980 100 CI C
B4
14 7
A5 NAND_DATA[5] R1942
CI_DATA[4] AR1905 100 CI 4.7K B Q1901
B5 A6 NAND_DATA[6] PCM_5V_CTL
CI_DATA[5] 13 8 2SC3052
CI CI
CI_DATA[6] B6
12 9
A7 NAND_DATA[7] E
CI_DATA[7] B7
11 10
GND
+5V_CI_ON
+3.3V_CI
+3.3V_CI
CI R1970 NAND F/M Data
22
IC1901
CI 74LVC125APW

C1901
1OE VCC 0.1uFOPT IC1902 3,3V_CI POWER
/CI_CE1 1 14 74AHC08PW +3.3V_CI
16V OPT
C1902
1A 4OE 0.1uF
NAND_REb 2 13 1A VCC
/CI_CE2 /CI_CE1 1 CI 14 16V
C1915 R1985 +3.3V_Normal +3.3V_CI
CI 9
1Y 4A OPT IC1905
/PCM_OE 3 12 NAND_WEb 1B 4B
0.1uF 10K
/CI_CE2 2 13 NAND_RBb 74LVC245A
16V CI
CI
2OE 4Y CI 45
4 11 1Y 4A VCC DIR
/PCM_IOWR /CI_EN1 3 12 20 1
L1901
R1986 22 OE
19 2
A0
BLM18PG121SN1D
2A 3OE /CI_EN1 CI_ADDR[2]
NAND_WEb 5 10 2A 4Y CI
/CI_EN1 4 11 CI_ADDR[1] B0
18 3
A1
PCM_ADDR[2] CI_ADDR[3] CI
2Y 3A B1 A2
CI 15 6 9 2B 3B PCM_ADDR[3] 17 4
CI_ADDR[4]
/PCM_WE NAND_REb 5 10 NAND_CLE B2 A3
CI C1907 CI C1908
16 5
GND 3Y PCM_ADDR[4] CI_ADDR[7] 0.1uF 0.1uF
7 8 CI 44 /PCM_IORD 2Y 3A
/PCM_CE1 CI 7 6 9 PCM_ADDR[7]
B3
15 6
A4
CI_ADDR[9]
B4 A5
14 7
GND 3Y PCM_ADDR[9] CI_ADDR[11]
7 8 CI_ADDR[0] B5 A6
13 8
PCM_ADDR[11] CI_ADDR[12]
B6 A7
12 9
PCM_ADDR[12] CI_ADDR[13]
B7 GND
11 10
PCM_ADDR[13]

CI DETECT

+3.3V_CI

+3.3V_CI +3.3V_CI
R1939 R1941
10K 10K IC1904
CI CI 74LVC1G32GW

B 1 5 VCC
CI CONTROL INTERFACE /CI_CD2 CI

A 2 C1911 R1966
/CI_CD1 OPT 0.1uF CI 10K
GND 3 4 Y
16V

CI
GND
R1965
CI_DET
47

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230 2010.11.11
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. CI 19 58

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DVB-S2 LNB Part Allegro
(Option:LNB)

D2301
LNB SMAB34 D2304
SMAB34

2A 40V 40V
LNB
3A
+12V_LNB
C2307 C2302 C2324 C2305
0.01uF 1uF 68uF 68uF
50V 50V 35V 35V LNB
LNB LNB LNB LNB L2301
33UH
SP-7850_33 C2311 C2312 DCDC_GND and A_GND are connected
close to Boost pin(#1)
10uF 0.1uF
2.4A
25V 50V DCDC_GND and A_GND are connected in pin#27
close to VIN pin(#25)
LNB LNB
DCDC_GND DCDC_GND PCB_GND and A_GND are connected
D2302 DCDC_GND
US1M(suzhou) A_GND
LNB_OUT
1000V
C2303 D2303 Input trace widths should be sized to conduct at least 3A
LNB SMAB34
0.1uF 40V
LNB 50V LNB
C2301 Ouput trace widths should be sized to conduct at least 2A
0.22uF
25V
GNDLX
[EP]

NC_9

A_GND
LNB

VIN

BFI

BFO
LX

A_GND
28

27

26

25

24

23

22

A_GND
BOOST 1 21 NC_8
C2304 0.1uF THERMAL
VCP 2 29 20 NC_7

LNB C2306 22000pF TCAP BFC

3 19
LNB NC_1 IC2301 NC_6
4 18
A8290SETTR-T
TDO 5 LNB 17 NC_5 A_GND
A_GND
R2313 R2314
EXTM 6 16 NC_4 0 0
LNB_TX
TDI NC_3 LNB LNB
7 15
10

11

12

13

14
8

+3.3V_Normal
GND

VREG

SDA

ADD

SCL

NC_2

IRQ

DCDC_GND
A_GND A_GND

R2304
Max 1.3A
4.7K
R2301 33

R2302 33

LNB
R2303 0

+12V +12V_LNB
LNB

LNB

LNB
0.22uF

L2302
BLM18PG121SN1D
27pF

27pF
LNB

OPT

OPT

LNB
C2308

C2309

C2310

A_GND
LNB_INT
SDA1_3.3V

SCL1_3.3V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
BCM35230 2010.11.02
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
LNB 23 57
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 NON CHB

TS Output
CHBO_TS_SERIAL
CHBO_TS_CLK
CHBO_TS_VAL_ERR
CHBO_TS_SYNC

CHB_RESET

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. NON CHB 28 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DUAL COMPONENT

5V_HDMI_1
HDMI_HPD_1 D3716 1ST : T-BAT54_SUZHO, 2ND : 0DSON00138A
OPT
C3726 OPT OPT
BODY_SHIELD 0.1uF VR3701 R3706
16V 10V
1K IC3702 1ST : EAN60991801, 2ND : T-AZ1117BH_1.8, 3RD : EAN54428201
20
HOT_PLUG_DETECT
19 GND
VDD[+5V] R3736 OPT0 DDC_SDA_1
18 OPT OPT

17
DDC/CEC_GND
R3737 VR3702
3.6K
DDC_SCL_1 * HDMI CEC
SDA 10V

16
SCL
HDMI_ARC
15
RESERVED
ARC
14
CEC R3707
CEC_REMOTE C3701 150
13 0.1uF
TMDS_CLK-
CK-_HDMI1 +3.5V_ST
12 R3708
TMDS_CLK_SHIELD +3.3V_Normal +3.3V_HDMI
11 63.4
TMDS_CLK+
CK+_HDMI1
10
TMDS_DATA0-
L3701
EAG62611201

D0-_HDMI1 R3717
9 BLM18PG121SN1D
TMDS_DATA0_SHIELD

G
27K
8
TMDS_DATA0+

120K
D0+_HDMI1

R3725
7
TMDS_DATA1-

Q3707
D
B
S

BSS83
D1-_HDMI1 D3716
6 C3727 C3728
TMDS_DATA1_SHIELD C3725
BAT54_SUZHO 0.1uF 10uF
5 16V 10uF
TMDS_DATA1+
D1+_HDMI1
4
TMDS_DATA2- CEC_REMOTE HDMI_CEC
D2-_HDMI1
3
TMDS_DATA2_SHIELD
2
TMDS_DATA2+
D2+_HDMI1
1

RSD-105156-100
JK3703
HDMI1
+3.3V_HDMI

+5V_Normal +5V_Normal
5V_HDMI_1 5V_HDMI_2
HDMI_HPD_2
5V_HDMI_2 OPT
C3702 OPT OPT
A2

A1

A2

A1
BODY_SHIELD 0.1uF VR3705 R3718 C3705 C3706 C3707 C3708 C3709 C3710
1K 10uF 10uF 10uF 0.1uF 0.1uF 0.1uF C3711
16V 10V D3713 D3715 0.1uF HDMI S/W OUTPUT
20
C

C
HOT_PLUG_DETECT

HDMI_CLK-

HDMI_RX0-

HDMI_RX0+

HDMI_RX1-

HDMI_RX1+

HDMI_RX2-

HDMI_RX2+
HDMI_CLK+
19 VDD[+5V] GND
R3704 OPT0 DDC_SDA_2
R3709 R3711 R3713 R3714
18 DDC/CEC_GND OPT OPT 4.7K 4.7K 4.7K 4.7K
R3701 VR3703 DDC_SCL_2
17 SDA 3.6K 10V

16 SCL DDC_SDA_1 DDC_SDA_2

15 RESERVED DDC_SCL_1 DDC_SCL_2

14 CEC
CEC_REMOTE
13 TMDS_CLK-
CK-_HDMI2
12 TMDS_CLK_SHIELD
EAG62611201

11 TMDS_CLK+
+5V_Normal
CK+_HDMI2 5V_HDMI_3
10 TMDS_DATA0-
D0-_HDMI2
9 TMDS_DATA0_SHIELD
A2

A1

TPWR_CI2CA
8 TMDS_DATA0+
D0+_HDMI2 D3714
7 TMDS_DATA1-

[EP]GND

VCC33_3
C

R3739
D1-_HDMI2 4.7K
6 TMDS_DATA1_SHIELD R3740 OPT

R0X2P
R0X2N
R0X1P
R0X1N
R0X0P
R0X0N
R0XCP
R0XCN
33

TXCN
TXCP
TX0N
TX0P
TX1N
TX1P
TX2N
TX2P
SCL1_3.3V
5 TMDS_DATA1+ R3710 R3712
D1+_HDMI2 4.7K 4.7K R3741 OPT 33
4 TMDS_DATA2- SDA1_3.3V
D2-_HDMI2
3 TMDS_DATA2_SHIELD

72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
DDC_SDA_3
2 TMDS_DATA2+
R1XCN 1 54 CSCL R3742 33
D2+_HDMI2 DDC_SCL_3 SCL3_3.3V
1 CK-_HDMI1
R1XCP 2 53 CSDA R3743 33
SDA3_3.3V
CK+_HDMI1 THERMAL
R1X0N 3 52 INT
D0-_HDMI1
73
RSD-105156-100 R1X0P 4 51 CEC_D
JK3701
HDMI2 EDID Pull-up D0+_HDMI1
R1X1N 5 50 CEC_A +5V_Normal
D1-_HDMI1
R1X1P 6 49 R4PWR5V R3729
C3715
D1+_HDMI1
R1X2N DSCL4 0
D2-_HDMI1
7 IC3701 48 1uF
R1X2P DSDA4 10V 5V_HDMI_3
D2+_HDMI1
8 SII9287B 47
R3738
VCC33_1 9 46 R3PWR5V 10
HDMI1
5V_HDMI_3
RSVD_1 CBUS_HPD3

C3712
HDMI_HPD_3
OPT
10 45 HDMI_HPD_3
C3703 OPT OPT

1/16W

R3727
0.1uF VR3706 R3719
R2XCN 11 44 DSCL3

1%
1K CK-_HDMI2 DDC_SCL_3 5V_HDMI_2

1K
16V 10V
BODY_SHIELD R2XCP DSDA3

1uF
CK+_HDMI2
12 43
DDC_SDA_3 R3733
20 R2X0N 13 42 R2PWR5V 10
HOT_PLUG_DETECT GND D0-_HDMI2

C3716
R2X0P 14 41 CBUS_HPD2
19 VDD[+5V] HDMI_HPD_2
R3705 OPT0

1/16W

R3734
D0+_HDMI2
DDC_SDA_3 R2X1N DSCL2
15 40

1%
18 DDC/CEC_GND

1K
OPT OPT D1-_HDMI2 DDC_SCL_2

1uF
R3702 VR3704 DDC_SCL_3 R2X1P 16 DSDA2
39
17 SDA 3.6K 10V D1+_HDMI2 DDC_SDA_2
R2X2N 17 SBVCC
38
16 SCL

C3714
D2-_HDMI2
R2X2P 18 MICOM_VCC33
37
15 RESERVED D2+_HDMI2

19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
14 CEC HDMI2

1uF
CEC_REMOTE
13 TMDS_CLK-
R3XCN
R3XCP
R3X0N
R3X0P
R3X1N
R3X1P
R3X2N
R3X2P
VCC33_2
RSVD_2
DSDA0
DSCL0
CBUS_HPD0
R0PWR5V
DSDA1
DSCL1
CBUS_HPD1
R1PWR5V
CK-_HDMI3
12 TMDS_CLK_SHIELD
5V_HDMI_1
EAG62611201

11 TMDS_CLK+
R3726
CK+_HDMI3 10
10 TMDS_DATA0-

C3713
D0-_HDMI3
9 TMDS_DATA0_SHIELD

1/16W

R3728
1%
8 TMDS_DATA0+ R3744

1K
100K

1uF
D0+_HDMI3
7 TMDS_DATA1-
D1-_HDMI3
6 TMDS_DATA1_SHIELD

5 TMDS_DATA1+
D1+_HDMI3
4 TMDS_DATA2-
D2-_HDMI3
3 TMDS_DATA2_SHIELD

2 TMDS_DATA2+
D2+_HDMI3
1

DDC_SDA_1

DDC_SCL_1

HDMI_HPD_1
CK-_HDMI3

CK+_HDMI3

D0-_HDMI3

D1-_HDMI3
D0+_HDMI3

D1+_HDMI3

D2+_HDMI3
D2-_HDMI3

RSD-105156-100
JK3702
HDMI3
HDMI3

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 HDMI 37 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 RGB/ PC AUDIO/ SPDIF/ EARPHONE/ RS232C

DUAL COMPONENT
+5V_Normal
RGB PC D3810 D3804,D3805,D3806
KDS184 D3807,D3808,D3813 1ST : EAH39491601, 2ND : EAH33945901
A2
D3814
C
A1 D3810 1ST : 0DD184009AA, 2ND : 0DSIH00028A
JK3803
+3.3V_Normal KJA-PH-0-0177
+5V_Normal GND 5
Q3801 1ST : 0TRIY80001A, 2ND : 0TR387500AA
IC3801
74F08D R3816
R3809 R3810 R3813
IC3802 2.7K L 4
D0A VCC AT24C02BN-SH-T 2.7K 2.7K 10K HP_LOUT
1 14
R3858
R3856 22 1K
A0 VCC DETECT 3
D0B
2 13
D3B 1 8 HP_DET
DSUB_VSYNC
A1 WP
R3857 22 Q0 D3A
2 7
EDID_WP R 1
3 12 HP_ROUT
A2 SCL 22 R3812
DSUB_HSYNC 3 6
RGB_DDC_SCL
R3850 0 D1A
4 11
Q3
GND SDA 22 R3811
4 5
OPT RGB_DDC_SDA
R3851 0 D1B
5 10
D2B R3852 0
OPT
Q1
6 9
OPT
D2A R3853 0
C3812
18pF
C3813
18pF EARPHON JACK
50V 50V
OPT
GND Q2
7 8

OPT
R3802 D3804 C3810
10K 30V 22pF
50V +3.3V_Normal

EARPHONE AMP L3803

OPT D3811 BLM18PG121SN1D
R3801 Closed to JACK D3809
D3805 LPF READEY
10K C3811 5.6V
30V 5.6V OPT (For H/P Noise Improvement)
22pF OPT
50V C3824 C3826
L3806 10uF 0.1uF
BLM15BD121SN1 10V 16V
R3862 L3804
0 BG2012B080TF
DSUB_B+ ESD_COMMON HP_LOUT
C3807 D3808 C3829
R3807 Close to the IC
C3823
47pF 30V 0.22uF
75 1uF
5.6V 50V 10V
10V
D3808-*1
ESD_CERADIODE

OUTL

SGND

VDD
+3.3V_Normal

EN
R3825
C3827 100K
C3818 16 15 14 13 2.2uF OPT
L3807 1uF 10V R3826 OPT
10V INL- HPVDD 4.7K R3827
BLM15BD121SN1 1 12
HP_LOUT_N 0
C3819
DSUB_G+ 1uF C
ESD_COMMON +3.3V_Normal 10V INL+ CPP R3828
R3806 C3808 D3806 2 11 1K
HP_LOUT_P Q3801 B
75 47pF 30V C3820 IC3804 C3828 2SC3052 SIDE_HP_MUTE
5.6V 50V 1uF
INR+ TPA6132A2 PGND 2.2uF
D3806-*1 R3814 10V 10V
ESD_CERADIODE 3 10 E
10K HP_ROUT_N
C3821
1uF
DSUB_DET 10V INR- CPN
1K R3815 4 EAN60724701 9
HP_ROUT_P
L3808
BLM15BD121SN1 5 6 7 8

R3819
D3812 D3812-*1

4.7K
R3817
5.6V

4.7K
5.6V

OUTR

G0

G1

HPVSS
DSUB_R+ ESD_COMMON ESD_COMMON ESD_CERADIODE
C3809 D3807
R3808 47pF 30V L3805
5.6V R3863

R3820
75 BG2012B080TF

R3818
50V 0

OPT
D3807-*1

OPT
HP_ROUT
ESD_CERADIODE
C3825 C3830
GREEN_GND

DDC_CLOCK
DDC_DATA

BLUE_GND

SYNC_GND

2.2uF 0.22uF
RED_GND

DDC_GND

10V
H_SYNC

V_SYNC

10V
GND_2

GREEN

GND_1
BLUE
RED

NC
SPG09-DB-010

SHILED
11

12

13

14

15

16
P3801

10
6

RS232C
1

10
5

9
0 R3829
IR_OUT 4
IR_OUT
R3860 8
100 JP3809

3
+3.5V_ST
7
R3859
100 JP3808

ESD_COMMON 2
D3814
PC AUDIO IC3803
ESD_COMMON
30V
6
D3813
MAX3232CDR 1
JK3801 30V
PEJ027-01
0.1uF C3814 C1+ VCC
3 E_SPRING 1 16 SPG09-DB-009
D3813-*1
D3814-*1
+3.5V_ST ESD_CERADIODE P3802
ESD_CERADIODE
6A T_TERMINAL1 V+ GND 5.6V
0.1uF C3815 2 15 5.6V
R3854
7A B_TERMINAL1 ESD_COMMON 22
PC_R_IN C1- DOUT1 R3830 R3831
3 14
D3802 4.7K 4.7K
4 R_SPRING C3803 C3806
AMOTECH R3804 OPT
470K 560pF 560pF C2+ RIN1 OPT
5.6V 50V 50V 0.1uF C3816 4 13
5 T_SPRING
R3821
R3855 C2- ROUT1 0
7B B_TERMINAL2 ESD_COMMON 22 5 12
PC_L_IN BCM_RX

T_TERMINAL2 D3801 R3822

6B AMOTECH C3802 C3805 0.1uF C3817 V- DIN1 0
R3803 6 11
5.6V 470K 560pF 560pF
50V 50V NEC_RXD

DOUT2 DIN2 R3823

7 10 0
BCM_TX
RIN2 ROUT2 R3824
8 9 0
NEC_TXD
EAN41348201

+3.3V_Normal

SPDIF OUT GND

1

Fiber Optic

JST1223-001
JK3802

R3805 VCC
2

2.7K
R3861
0 VINPUT
3

SPDIF_OUT
C3804
4

D3803
30V 0.1uF
16V
FIX_POLE

OPT

HIGH : SELECT X1, Y1, SELECT MAIN TX/RX

LOW : SELECT X0, Y0, SELECT MICOM TX/RX

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 COMM JACK 38 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Ethernet Block

+2.5V_BCM35230

L3901
MLB-201209-0120P-N2

JK3901
XRJV-01V-D12-180

1
EPHY_TDP

2 D3906
C3901 ADLC 5S 03 015
0.1uF 5.5V
16V
3
EPHY_TDN

4
EPHY_RDP
D3902 D3905
ADLC 5S 03 015 ADLC 5S 03 015
5 5.5V 5.5V
C3902
0.1uF
16V
6
EPHY_RDN

D3901
7 ADLC 5S 03 015
5.5V
8 +3.3V_Normal

D1 R3901 240

D2
EPHY_LINK
D3903
ADLC 5S 03 015
D3 R3902 240 5.5V

D4
EPHY_ACTIVITY
D3904
9 ADLC 5S 03 015
5.5V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 ETHERNET 39 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DUAL COMPONENT

D4101,D4102 1ST : EAH42720601 2ND : EAH60994401

+3.3V_Normal
USB
IC4101
+5V_USB
AP2191DSG
R4101
L4101 NC GND 4.7K
8 1
MLB-201209-0120P-N2 OPT
OUT_2 IN_1
7 2

120-ohm OUT_1
6 3
IN_2

FLG EN
C4103
C4102 C4101 5 4
0.1uF
R4102
100uF 10uF 2.7K 16V
16V 10V

SIDE_USB_CTL1
SIDE_USB_OCD1
3AU04S-305-ZC-(LG)
P4101

1
USB DOWN STREAM

SIDE_USB_DM
RCLAMP0502BA
3

SIDE_USB_DP

OPT D4101 D4102

D4103
4

CDS3C05HDMI1 CDS3C05HDMI1
5.6V 5.6V
5

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 EU USB 41 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 3D_SYNC_RF

[FHD120Hz LVDS output(51pin+41Pin)]

P4202
P4201
FI-RE41S-HF-J-R1500
FI-RE51S-HF-J-R1500

1 1
R4205 33 FRC2
2 3D_SYNC_RF 2
LVDS_SEL
3 3
R4206 33 FRC2 +3.3V_Normal
4 SDA2_3.3V 4
R4207 33 FRC2
5 SCL2_3.3V 5
R4212
R4208 33 FRC2
6 FRC_RESET 3.3K 6
LVDS_SEL_HIGH
7 7
R4213
8 8
10K
9 LVDS_SEL_LOW 9

10 10 TXC0N
11 11 TXC0P
12 TXA0N 12 TXC1N
13 TXA0P 13 TXC1P
14 TXA1N 14 TXC2N
15 TXA1P 15 TXC2P
16 TXA2N 16

17 TXA2P 17 TXCCLKN
18 18 TXCCLKP
19 TXACLKN 19

20 TXACLKP 20 TXC3N
21 21 TXC3P
22 TXA3N 22 TXC4N
23 TXA3P 23 TXC4P
LVDS_10bit
R4214 0
24 TXA4N 24
R4215 0
25 TXA4P 25
LVDS_10bit
26 BIT_SEL 26 TXD0N
27 27 TXD0P
28 TXB0N R4211 28 TXD1N
10K
29 TXB0P BIT_SEL_LOW 29 TXD1P
30 TXB1N 30 TXD2N
31 TXB1P 31 TXD2P
32 TXB2N 32

33 TXB2P 33 TXDCLKN
34 34 TXDCLKP
35 TXBCLKN 35

36 TXBCLKP 36 TXD3N
37 37 TXD3P
38 TXB3N 38 TXD4N
LVDS_10bit
39 TXB3P 39 TXD4P
R4216 0
40 TXB4N 40
R4217 0
41 TXB4P 41
LVDS_10bit
42
42
43

44

45

46

47 PANEL_VCC
48

49 L4201
MLB-201209-0120P-N2
50

51

52 C4201 C4202 C4203

10uF 1000pF 0.1uF
25V 50V 50V
OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 EU LVDS 42 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DUAL COMPONENT +3.3V_Normal AMP_RESET_N

C4615
1000pF
Q4601 50V
1ST : 0TRIY80001A 2ND : 0TR387500AA

50V
L4602
+24V_AMP

22000pF
BLM18PG121SN1D

C4616
OPT
AUD_MASTER_CLK R4607
3.3

+24V_AMP OPT
+24V
C4624

OUT1A_2
OUT1A_1
PVDD1_3
PVDD1_2
PVDD1_1
C4618 C4620 C4622
0.1uF 0.1uF 10uF 0.01uF

VDD_IO

GND_IO

/RESET

PGND1A
C4614 C4640 50V
10uF 50V 50V 35V

CLK_I

BST1A
L4601 0.1uF 10V
MLB-201209-0120P-N2 16V [EP] D4601
SPK_L+

AD
1N4148W R4608 R4615 L4605
100V 12 12 R4616
OPT 10.0uH C4636
OPT C4610 C4612 OPT 0.1uF 4.7K
C4601 C4602 C4606 C4608 10uF 0.1uF C4629 50V
0.1uF 0.1uF 10uF 0.1uF 10V 390pF L4606
50V 50V 10V 16V 50V C4634
16V 10.0uH 0.47uF
48
47
46
45
44
43
42
41
40
39
38
37
C4604
1000pF
50V
50V
SPEAKER_L
C4603 C4630 C4637
100pF R4605 AGND_PLL 1 36 OUT1B_2 D4602
390pF
50V 0.1uF
50V
R4617
50V 3.3K 1N4148W R4609 R4613 4.7K
AVDD_PLL 2 35 OUT1B_1 100V
OPT
12 12
THERMAL SPK_L-
DVDD_PLL 3 49 34 PGND1B C4625
22000pF
LF 4 33 BST1B 50V WAFER-ANGLE

DGND_PLL IC4601 VDR1

5 32 SPK_L+
OPT 4
C4611
10uF
GND_1 6 NTP-7400L 31 VCC_5
C4613
10V 0.1uF SPK_L-
16V DGND 7 30 GND_2 3

DVDD 8 29 VDR2 SPK_R+

2
C4627 C4628 C4633
SDATA 9 28 BST2A 1uF
25V
1uF
25V
1uF
25V SPK_R-
AUD_LRCH 1
WCK 10 27 PGND2A C4626
P4601
AUD_LRCK 22000pF
50V
BCK 11 26 OUT2A_2
AUD_SCK

R4603 100 SDA 12 25 OUT2A_1

SDA3_3.3V
13
14
15
16
17
18
19
20
21
22
23
24

R4604 100
SCL3_3.3V
C4607 C4609
+3.5V_ST 33pF 33pF
50V 50V SPK_R+
SCL
/FAULT
MONITOR0
MONITOR1
MONITOR2
BST2B
PGND2B
OUT2B_1
OUT2B_2
PVDD2_1
PVDD2_2
PVDD2_3

+24V_AMP D4603 R4610 R4614

R4602 1N4148W 12
10K 12 L4603
100V 10.0uH C4638 R4618
R4606 OPT
C4631 0.1uF 4.7K
C 100 C4605 390pF L4604 C4635 50V
50V 0.47uF
R4601 B Q4601
1000pF C4619 C4621 C4623
10.0uH 50V
SPEAKER_R
AMP_MUTE 50V C4632
10K 2SC3052 0.1uF 0.1uF 10uF 390pF
50V 50V 35V D4604 50V C4639 R4619
E
C4617 1N4148W R4611 R4612 0.1uF 4.7K
22000pF 100V 12 12 50V
OPT
50V
SPK_R-

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 EU AMP 46 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DUAL COMPONENT
D4703,D4704
1ST : EAH42720601, 2ND : EAH60994401
D4705,D4706

+3.5V_ST

IR & KEY
EEPROM_SCL R4705 P4701
100 P4702
R4701 R4702 12507WR-15L 12507WR-12L
10K 10K D4706
1% 1% CDS3C05HDMI1
5.6V IR_15PIN IR_12PIN
R4710 1 1
100
KEY1 R4706
EEPROM_SDA 100
R4711 D4702 2 2
+3.5V_ST 100 5.6V
KEY2 D4707
AMOTECH CDS3C05HDMI1
C4701 C4703 5.6V 3 3
0.1uF 0.1uF
+3.5V_ST D4701
R4712
47K 5.6V
COMMERCIAL AMOTECH 4 4
R4714 +3.5V_ST +3.5V_ST
IR
47K
R4713 COMMERCIAL 5 5
Q4701 C 10K
R4717 L4701
2SC3052 B
3.3K BLM18PG121SN1D
COMMERCIAL E COMMERCIAL R4716 OPT 6 6
C 47K
B
Q4702 ECOMMERCIAL OPT OPT
C4702 C4704 C4705 R4707 1.5K 7 7
2SC3052 0.1uF 0.1uF 1000pF LED_B/LG_LOGO
COMMERCIAL 16V 16V 50V

8 8

R4709
0
9 9
D4705
C4708 5.6V
100pF AMOTECH
+3.3V_Normal 50V 10 10
L4702
BLM18PG121SN1D
+3.5V_ST 11 11
COMMERCIAL
C4709 C4710 R4708
OPT 0.1uF OPT 0.1uF LED_R/BUZZ 12 12
+3.5V_ST
R4719 16V 16V 1.5K
47K
R4715 COMMERCIAL 13
22 13
IR_OUT R4721
COMMERCIAL 47K R4703
S/T_SCL
R4720 COMMERCIAL 100
Q4703 C 10K 14
2SC3052 B
COMMERCIAL_EU E R4722
COMMERCIAL_EU C 47K D4703 15
B CDS3C05HDMI1
Q4704 E COMMERCIAL 5.6V
2SC3052 16
COMMERCIAL R4704
S/T_SDA 100
OPT
R4718
0 D4704
CDS3C05HDMI1
5.6V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 EU IR 47 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 5V_HDMI_4
AV2_CVBS_IN

SIDE_USB_CTL2

SIDE_USB_OCD2 3D_SYNC
M_REMOTE_TX

M_REMOTE_RX L_VS

DD_MREMOTE
M_RFModule_RESET

WIRELESS_DET

WIRELESS_PWR_EN

3D_GPIO_2

3D_GPIO_1

3D_GPIO_0

/RST_HUB

DC_MREMOTE

WIFI_DP

WIFI_DM
AV2_CVBS_DET

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 EU 48 50

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 THE
M1-*3 M1-*2 M1-*1 M1
MDS62110206 MDS62110204 MDS62110210 MDS62110208
GASKET_6.5T GASKET_5.5T GASKET_5.0T GASKET_4.5T

M2-*3 M2-*2 M2-*1 M2

MDS62110206 MDS62110204 MDS62110210 MDS62110208

GASKET_6.5T GASKET_5.5T GASKET_5.0T GASKET_4.5T

M3-*3 M3-*2 M3-*1 M3

MDS62110206 MDS62110210 MDS62110208
MDS62110204
GASKET_6.5T GASKET_5.0T GASKET_4.5T
GASKET_5.5T

Only for training and service purposes

M4-*3 M4-*2 M4-*1 M4

MDS62110206 MDS62110204 MDS62110210 MDS62110208

GASKET_6.5T GASKET_5.5T GASKET_5.0T GASKET_4.5T

THE CRITICAL COMPONENTS IN THE

M5-*3 M5-*2 M5-*1 M5

MDS62110206 MDS62110204 MDS62110210 MDS62110208

GASKET_6.5T GASKET_5.5T GASKET_5.0T GASKET_4.5T

Copyright © 2011 LG Electronics. Inc. All rights reserved.

M6-*1 M6
M6-*3 M6-*2

SMD GASKET 4.5T

MDS62110208

SMD GASKET 6.5T

MDS62110210

SMD GASKET 5.0T

MDS62110206

SMD GASKET 5.5T

MDS62110204
SMD GASKET
GASKET_6.5T GASKET_5.0T GASKET_4.5T
GASKET_5.5T
M7-*3 M7-*1 M7

MDS62110206 M7-*2 MDS62110210 MDS62110208

GASKET_6.5T MDS62110204 GASKET_5.0T GASKET_4.5T
GASKET_5.5T
M8-*1 M8
M8-*3
M8-*2 MDS62110208
MDS62110206 MDS62110210
MDS62110204 GASKET_5.0T GASKET_4.5T
GASKET_6.5T
GASKET_5.5T
M9-*3 M9-*1 M9
MDS62110206 M9-*2 MDS62110210 MDS62110208
GASKET_6.5T GASKET_5.0T GASKET_4.5T

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

MDS62110204

SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

GASKET_5.5T

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

M10-*3 M10-*1 M10

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

MDS62110206 M10-*2 MDS62110210 MDS62110208
GASKET_6.5T GASKET_5.0T GASKET_4.5T
MDS62110204

SYMBOL MARK OF THE SCHEMETIC.

M11-*3 GASKET_5.5T M11-*1 M11
MDS62110206 M11-*2 MDS62110210 MDS62110208
GASKET_6.5T GASKET_5.0T GASKET_4.5T
MDS62110204
GASKET_5.5T
M12-*3 M12-*1 M12

MDS62110206 M12-*2 MDS62110210 MDS62110208

GASKET_6.5T GASKET_5.0T GASKET_4.5T
MDS62110204
GASKET_5.5T

GASKET3.5T_HEATSINK M1-*6 M1-*4

M1-*5
MDS62110213 MDS61887710 MDS62110205
GASKET_9.5T MDS62110209 GASKET_7.5T
M20
GASKET_8.5T
M2-*6 M2-*5 M2-*4
GASKET3.5T_HEATSINK MDS61887710 MDS62110209 MDS62110205
GASKET_9.5T GASKET_8.5T GASKET_7.5T
MDS62110213
M21 M3-*6 M3-*4
MDS61887710 M3-*5 MDS62110205
GASKET_9.5T MDS62110209 GASKET_7.5T
GASKET3.5T_HEATSINK GASKET_8.5T
MDS62110213 M4-*6
M4-*4
M22 MDS61887710 M4-*5
MDS62110205
GASKET_9.5T MDS62110209 GASKET_7.5T
GASKET_8.5T
GASKET3.5T_HEATSINK M5-*6 M5-*4
MDS62110213 MDS61887710 M5-*5 MDS62110205
GASKET_9.5T GASKET_7.5T
M23 MDS62110209
GASKET_8.5T
M6-*6
M6-*4
M6-*5
MDS61887710
SMD GASKET 8.5T

SMD GASKET 9.5T

SMD GASKET 7.5T

MDS62110205
GASKET_9.5T MDS62110209 GASKET_7.5T
GASKET_8.5T
M7-*6 M7-*4
MDS61887710 M7-*5 MDS62110205
GASKET_9.5T GASKET_7.5T
MDS62110209
GASKET_8.5T
M8-*6
M8-*4
MDS61887710 M8-*5 MDS62110205
GASKET_9.5T GASKET_7.5T
MDS62110209
GASKET_8.5T
M9-*6 M9-*4
MDS61887710 M9-*5 MDS62110205
GASKET_9.5T GASKET_7.5T
MDS62110209
M10-*6 GASKET_8.5T
M10-*4
MDS61887710 MDS62110205
M10-*5
GASKET_9.5T GASKET_7.5T
MDS62110209
M11-*6 GASKET_8.5T M11-*4
MDS61887710 M11-*5 MDS62110205
GASKET_9.5T GASKET_7.5T
MDS62110209
M12-*6 GASKET_8.5T
M12-*4
MDS61887710 MDS62110205
M12-*5
GASKET_9.5T GASKET_7.5T
MDS62110209
GASKET_8.5T

BCM35230

SMD GASKET
56
56
2010. 09. 18

LGE Internal Use Only

 DUAL COMPONENT +12V

FROM LIPS & POWER B/D Q501,Q504,

Q505,Q506 1ST : 0TRIY80001A 2ND : 0TR387500AA L511
PANEL_POWER TYP 1450mA
+3.5V_ST 12V_PANEL
RT1P141C-T112 MLB-201209-0120P-N2
Q502 1ST : 0TRIH80004A, 2ND : EBK61012501, 3RD : 0TR102009AM
Q502
C551 PANEL_VCC
Q507 C550 0.1uF
R508 1 3 1ST : EBK60752501, 2ND : EBK61011501 0.01uF 50V
4.7K NORMAL_26~55 50V
R502 C Q507
2 P502
+24V AO3407A
RL_ON 10K
B Q501
FW20020-24S IC502,IC503 1ST : EAN61151001, 2ND : EAN60670101

D
2SC3052

5V_PANEL

PANEL_DISCHARGE_REG
R558-*1

12V_PANEL12V_PANEL
R558

PANEL_DISCHARGE_REG
C560
10K
C552

OPT 1uF
25V
E L504
PWR ON 1 2 24V 10uF
MLB-201209-0120P-N2

22K
G

1/8W

1/8W
24V 24V 25V C563

R575

R576
2K

2K
3 4
GND GND 0.1uF
+3.5V_ST 5 6
L503 C519
OS Module OPT R555 50V

5V_PANEL
R559-*1

R559
1.8K
GND 7 8 GND 0.1uF
MLB-201209-0120P-N2 22K
3.5V 3.5V 50V

2.7K
9 10
3.5V 11 12 3.5V
C508 POWER_16_URSA_SCAN OPT
GND GND R574 0 C
0.1uF 13 14 L_VS R532 R554
GND GND/V-sync R573 0 100 POWER_18_INV_CTL 10K B Q506
16V 15 16 L/DIM0_VS
12V INV ON POWER_16_BCM_SCAN INV_CTL_18 2SC3052
17 18 INV_CTL_18 R533 POWER_18_A_DIM
12V [Link] A_DIM C
19 20 A_DIM_20 0 R553 R557 E
+12V 12V 21 22 P.DIM1 47K B Q505 22K
PWM_DIM_22 POWER_20_A_DIM PANEL_CTL
L501 GND/P.DIM2 Err OUT 2SC3052
MLB-201209-0120P-N2 23 24 R531 0 A_DIM
A_DIM_20
SLIM_32~55 POWER_20_PWM_DIM E
POWER_16_GND

ERROR_OUT_24 PWM_DIM
C506 R538 0
25
R518

0.1uF
50V SMAW200-H24S2 +3.3V_Normal
0

P501
ERROR_OUT_PULL_UP
R523
4.7K

+3.5V_ST
ERROR_OUT +3.3V_Normal
#16/#20/#23
LD - GND OR USE
R529 0
POWER_20_ERROR_OUT R546
1K
R551
OPT
+1.5V_DDR Max 800mA
POWER_22_A_DIM 10K
LE(N.L.D.) - OPEN R535 0 A_DIM
PWM_DIM_22
LE(L.D.) - USE POWER_22_PWM_DIM R543
C
R547 +3.5V_ST
PWM_DIM INV_CTL
R526 0 R540 0 6.8K B 10K IC508
NON_OPC/NON_IOP +1.5V_DDR
R527 0 OPT Q504 AP7173-SPG-13 HF(DIODES)
2SC3052 L517
E R552
BLM18PG121SN1D [EP]
POWER_24_PWM_DIM 10K
OPT

Power_DET ERROR_OUT_24
POWER_24_INV_CTL IN
1 8
OUT

POWER_24_GND
100 R537

THERMAL
0
PG FB
R1

9
+12V +3.5V_ST 2 7
R517 ERROR_OUT
100K +3.5V_ST R541 0
R595

R524
POWER_24_ERROR_OUT
VCC SS 4.3K
PD_+12V PD_+3.5V R522 3 6 1%
R512 R515 10K C594 C591
2.7K 0 IC503
NCP803SN293
OPT R591
1.5A 22uF 0.1uF
1% 5% POWER_ON/OFF1 10K EN GND C593 10V 16V
<OS MODULE PIN MAP> 4 5
560pF
R593
R520 POWER_DET 3.9K
VCC RESET 100 50V 1%
3 2 R2
1 PIN No LGD CMO(09) AUO SHARP C590 R592
C580 10uF 1K
PD_+12V 0.1uF 1%
GND 10V
R513 16V
1.21K ESD INV_ON A-DIM INV_ON
18 INV_ON
1% C520
0.1uF
16V V4:VBR-A
20 V5:NC NC Err_out Err_out
PD_+18.5_20_24V
+24V R516 22 PWM_DIM PWM_DIM A-DIM PWM_DIM
100K

PD_+18.5V PD_+18.5_20_24V
not to RESET at 8kV ESD
24
Err_out
LED:GND INV_ON PWM_DIM GND Vout=0.8*(1+R1/R2)
PD_+20V
R510-*4 R510-*3 PD_24V IC502
5.6K 4.7K R510 NCP803SN293
1% 1% 8.2K
1% R519
CHECK PWR/MODULE PIN MAP
VCC 3 2 RESET 100 15V-->3.6V
20V-->3.5V
PD_+20V PD_+18.5V 1 PD_+18.5_20_24V
R511-*4 R511-*3
PD_24V C581 24V-->3.48V
1.3K
1%
1.21K
R511
1.5K
0.1uF
16V
GND
12V-->3.58V
ST_3.5V-->3.5V
+5V_Normal MAX 1A
1% 1% PD_+18.5_20_24V
+12V +3.3V_NORMAL MAX 2.8A
+5V_Normal
+12V IC507
L507
AOZ1073AIL-3
IC505
BLM18PG121SN1D [EP]PGND TPS54425PWPR +3.3V_Normal L516
+0.9V_CORE_BCM35230 VIN2 VO
L514
BLM18PG121SN1D
PGND
1 8
LX_2 3.6uH

14 1 NR8040T3R6N
VIN LX_1
THERMAL

+12V 2 7

R570
R534

1%
51K
15

VIN1 VFB 10K

13 2
C501
10uF
C502
10uF
C535
0.1uF 1% Placed on SMD-TOP AGND
3
3A 6
EN POWER_ON/OFF2_1
R1
C568
22uF
C570
22uF
16V 16V 50V R562 10V 16V

3.6K
L502 VBST VREG5 C546 R566

1%
0

R571
OPT OPT 12 3 10K
BLM18PG121SN1D Max 7350 mA R2 10uF
FB COMP R564 12K
1/10W C512 16V
5% SW2
4A SS
1uF
25V R530
4 5
C557
OPT
C559
C511 11 4 33K 0.1uF C565
Placed on SMD-TOP 1% 2200pF 100pF
0.1uF R521 C595 16V
50V 22pF 50V
SW1 GND 0 R1
10 5 50V OPT
R509 C514 R525
3300pF 330
100K 1%
PGND2 PG 50V
C503 C505 9 6
10uF 10uF

R572
16V 16V

1%
10K
PGND1 EN R514 10K
8 7
C537
POWER_ON/OFF2_2
R2
0.1uF +3.3V_Normal
OPT
Vout=0.8*(1+R1/R2) Switching freq: 500K
POWER_ON/OFF2_2 Q503
AON7430
L508
2uH

R503
D 5 4

3
G

S_3
C517
22uF
10V
C518
22uF
10V +12V
+5V_USB+WIFI MAX 1.9A
1K
IC501
TPS40192DRCR EP_GND
C504
100pF
2 S_2
Vout=0.8*(1+R1/R2) L513 +5V_USB
+0.9V_CORE
50V ENABLE HDRV 1 S_1 CIC21J501NE
1 10 R577 4.7 L505 IC506

+2.5V_BCM35230 MP8706EN-C247-LF-Z
THERMAL

0.9V_CORE_FB +2.5V_BCM35230
Max 960 mA
11

FB SW
0.47uF

2 9 1uH OPT
OPT
C515

R504 C510 C522 C524 C525

25V

C523 IN GND
2K 0.01uF 22uF 22uF 47uF 10uF IC504 1 8
50V COMP BOOT
3 8 10V 10V 10V 10V AP2132MP-2.5TRG1 [EP] C528

R549
OPT

1%
33K
C509 50V 1uF C529
220pF G 4 5 D +3.5V_ST SW_1 VCC C530 C532 C534 C536
2 7 50V 100pF 100pF 22uF 0.1uF 0.1uF
VDD LDRV
+3.3V_Normal 4 7 R578 4.7 C521 50V 50V 10V 16V 16V
4.7uF

1 8 R1
3A R542
C516

S_3 3 10uF OPT

10V

OPT SW_2 FB 10K

THERMAL

TEST R507 PG GND R544 25V 3 6

120-ohm

10K OPT PGD BP5 R528 18K R2

5 6 POWER_ON/OFF2_1 10K C526
L506

S_2 2 2 7 1%
0.1uF POWER_ON/OFF2_1
C513 BST EN/SYNC

R550
6.2K
C507 0.1uF EN ADJ R545

1%
4 5
1000pF 16V S_1 1 56K R1
50V R506 3 6 1% R539 R548
330 22 10K
R536

EAN31346002
R2
10K

AON7200 VIN VOUT

R505 C533
Q508
C527 0.1uF
OPT
4 2A 5
6.8K 10uF +5V_Normal L509
VCTRL NC C538 C539
1% R1 0.9V_CORE_FB 3.6uH
6.3V EAN61387601 47uF 10uF
10V 6.3V
R501 NR8040T3R6N
12K
1%
R2 Vout=(1+R1/R2)*0.8
Vout=0.591*(1+R1/R2) Switching freq: 600K C531
1uF
OPT

Vout=0.6*(1+R1/R2) Vout=0.8*(1+R1/R2)
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. POWER 5 58

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Option Table
H/NIM & F/NIM & T/C/S2 Combo Tuner DUAL COMPONENT

IC2204 1ST:T-AP2114H(EAN61573601) / 2ND:T-TJ3940S (EAN61573501)

Non_S: not use DVB-T/C/S2 combo Tuner(use H/NIM and F/NIM)
H/NIM F/NIM_T/C DVB-T/C/S2
(EU) (Eu,Aisa) S: use DVB-T/C/S2 combo Tuner

H/NIM: use H/NIM(H/NIM, DVB-T/C/S2 combo Tuner)

Non_S Non_S S
F/NIM: use F/NIM(EU_T/C, EU_DVB-T2, China)
H/NIM F/NIM H/NIM
SCART: use Scart Jack
SCART SCART SCART
CN : use China F/NIM +5V_TU
BOOSTER BOOSTER
EU_BR_F/NIM
BOOSTER: use BOOSTER_CTL ERROR & VALID PIN
RF_SW_CTL: use RF_SWITCH_CTL
RF_SW_CTL BOOSTER <EU, China, Brazil,S2> R9163
L9101 0
EU_F/NIM TC_F/NIM: use EU_DVB-T/C F/NIM
BLM18PG121SN1D DVB_T2/CN_F/NIM_BR
TC_F/NIM

EU_F/NIM: use EU_F/NIM IC9103

NL17SZ08DFT2G +3.3V_TU
* DVB-T/C/S2 combo Tuner: DVB-T/C is H/NIM, and DVB-S2 is F/NIM EU_BR_F/NIM: use EU_F/NIM and Brazil F/NIM
BOOSTER BOOSTER
R9131
R9142 R9158
0 TU_TS_VAL 0 IN_B VCC
R9109 BOOSTER 10K 1 5
Q9102 DVB_TC/TCS_F/NIM C9171
RF_SWITCH_CTL
0 RF_SW_CTL 0.1uF
E MMBT3906(NXP) TU_TS_ERR IN_A 16V
R9135 2
C9103 OPT
RF_SW_CTL 0.1uF close to TUNER R9169
B 2.2K
16V BOOSTER C GND OUT_Y 0
R9146 3 4 TS_VAL_ERR
C
TU9101 TU9102 TU9103 Q9103
2SC3052
B 10K
RF_BOOSTER_CTL
DVB_TC/TCS_F/NIM

+5V_TU C9134 BOOSTER

TDTJ-S101D TDFR-G136D TDFQ-G001D L9105 0.01uF
50V
E
DVB_TC/TCS_F/NIM
1uH close to
NON_DVB_S
TUNER BOOSTER
AU_ASIA_TUNER_H HORIZONTAL_T HORIZONTAL_S C9122 C9125
100pF 0.1uF
16V
ANT_PWR NC_1 NC_1 50V
NON_DVB_S NON_DVB_S +3.3V_S2_TU close to TUNER
1 1 1 +5V_TU Tuner to CI Slot R9166
0
TS_VAL_ERR NIM_VAL_ERR
NC_1 BST_CNTL NC_2 BOOSTER
2 2 2 0 R9134 R9167
L9106-*1 L9110-*1 470 0
R9106 C9184 C9185 C9186 DVB_S DVB_S R9137 TU_TS_SYNC NIM_TS_SYNC
+B1[5V] +B1[5V] NC_3 100pF 0.1uF 10uF 0 0 DVB_S 82 +5V_TU
3 3 3 50V 16V 6.3V TU_SIF R9168
DVB_S DVB_S DVB_S close to TUNER C9135 E DVB_S 0
RF_AGC NC_2[RF_AGC] S2_TU[3.3V] DVB_S
R9177 L9106 DVB_S TU_TS_CLK NIM_TS_CLK
4 4 4 270nH NON_DVB_S
C9101 B
0 0.1uF
MOPLL_AS NC_3 NC_4 0.1uF
SCL0_3.3V R9130 Q9101 R9143
5 5 5 16V close to TUNER L9110 16V 4.7K
C MMBT3906(NXP) 0
R9150
OPT 270nH NON_DVB_S 1K R9152 R9153
DVB_S DVB_S NON_DVB_S 220 220
SCL SCLT TU_SCL +1.8V_TU SDA0_3.3V
OPT
6 6 6 C9119 C9121 C9102 C9111
62pF 62pF 20pF OPT 0
SDA SDAT TU_SDA 50V 50V 50V
20pF
TU_CVBS
Max 1.5A
7 7 7 NON_DVB_S50V
NON_DVB_S NON_DVB_S NON_DVB_S R9148
C9104 C9108 E
100pF 0.1uF 0
NC_2 NC_4 T_1.8V 50V
8 8 8 16V +1.25V_TU (EU)
DVB_S DVB_S R9149 B Q9104
1K R9151 MMBT3906(NXP) +5V_TU +1.23V_TU (CN)
SIF SIF T_SIF OPT
C
9 9 9
R9191 +1.25V_TU
NC_3 NC_5 NC_5 75 +3.3V_TU IC9108
10 10
close to TUNER R9154 R9155
10 OPT
R9147 200 200 AP2132MP-2.5TRG1 [EP]
0 SCART SCART
VIDEO VIDEO T_CVBS +3.3V_TU SCART
11 11 11 R9112
20K R2
+1.25V_TU ATV_OUT 1 8
1%
GND GND GND_1 E

THERMAL
12 12 12 PG GND
R9110
CN C9115 +3.3V_TU R9133
POWER_ON/OFF2_1 10K
R9113

9
C9105 C9120 C9118 CN 2 7 11K
+B2[1.2V] +B2[1.2V] TD_1.2V

NON_CN
C9110 C9114 R9129 100K B 1%
13 13 13 10uF 100pF 1000pF 4700pF 0.1uF 100uF 100 Q9105
EN ADJ R9114 R1
50V 50V CN 50V CN C9117 TU_RESET MMBT3906(NXP)
16V 16V 16V CN C9131 +2.5V_TU C SCART
11K
+B3[3.3V] +B3[3.3V] T_3.3 C9127 C9138 3 6 1%

R9111
10uF 100pF 0.1uF 0.1uF
14 14 14

OPT 10K
50V 16V 16V VIN VOUT
16V EU_F/NIM C9189 C9191

15
RESET
15
RESET
15
T_TU_RESET R9140 0
10uF
0.1uF
OPT
4 2A 5
R9114-*1
10K
H/NIM +5V_Normal NC
0 16V VCTRL 1/16W
IF_AGC +B4[2.5V] NC_6
R9141
IF_AGC OPTION:SCART EAN61387601 1% C9190
C9113
16 16 16 0.1uF EU_F/NIM
CN
10uF
F/NIM 16V R9115
DIF_1[N] SCL TD_SCL R9104 0 close to Tuner 22
16V
17 17 17 SCL1_3.3V
R9116 OPT
DIF_2[P] SDA TD_SDA R9105
F/NIM
0 close to TUNER 22 C9192
18 18 18 SDA1_3.3V 1uF
close to IF line
H/NIM
ERR T/C/S2_ERROR R9193 0
19 19 C9137 C9141
19 R9192H/NIM
0 18pF
SYNC T/C/S2_SYNC 50V
OPT
18pF
50V
Vout=0.6*(1+R1/R2)
20 20 OPT
SHIELD
VALID T/C/S2_VALID IF_N
21 21
MCL T/C/S2_MCL
22 22 IF_P
D0 T/C/S2_D0
23 23
AR9100 47 +3.3V_TU +2.5V_TU
D1 T/C/S2_D1 TU_TS_ERR
24 24 FE_TS_DATA[0-7]
TU_TS_SYNC
IC9104
D2 T/C/S2_D2 TU_TS_VAL
25 25 TU_TS_CLK AR9100-*1 AR9100-*2 AP2114H-2.5TRG1
0 33
EU_F/NIM CN DVB_S
D3 T/C/S2_D3 VIN VOUT
26 26 3 2
1
D4 T/C/S2_D4 R9170
1
27 27 C9168
GND
EU_F/NIM
AR9101 OPT 0.1uF
D5 T/C/S2_D5 47
16V C9176 C9179
28 28 FE_TS_DATA[0] 10uF 0.1uF
AR9101-*1 AR9101-*2 10V 16V
D6 T/C/S2_D6 FE_TS_DATA[1] 0 33 EU_F/NIM
CN EU_F/NIM
29 29 FE_TS_DATA[2] DVB_S
FE_TS_DATA[3]
D7 T/C/S2_D7
30 30 L9109 EU_F/NIM
31
S2_1.25V BLM18PG121SN1D
120-ohm
+1.25V_TU AR9102
31 47
DVB_S C9123 C9126 C9130 FE_TS_DATA[4]
S2_RESET 100pF 0.1uF 10uF FE_TS_DATA[5] AR9102-*1 AR9102-*2
Max 217mA
SHIELD 32 50V 16V 10V FE_TS_DATA[6]
0
CN
33
DVB_S DVB_S DVB_S DVB_S
S2_3.3V +3.3V_S2_LNB
+3.3V_TU
+1.8V_TU
33 R9108 +3.3V_TU +3.3V_S2_LNB
R9103 2.2K EU_F/NIM IC9102
TU9101-*1 S2_F22 R9102 100 DVB_S
51 LNB_TX S2_RESET AZ1117BH-1.8TRE1
TDTR-T036F 34 DVB_S C9107 L9104
0.1uF MLB-201209-0120P-N2
TU9102-*1 1/16W DVB_S
TDFR-G236D
Taiwan_BR_H S2_SCL 5%
DVB_S
IN 3 DVB_S 2 OUT
RF_S/W_CTL 35 R9183 0 R9126
1 FE_TS_DATA[7] R9126-*1 R9126-*2
HORIZONTAL_T2 47 0 33 1 R9198 C9142 DVB_S C9145 C9148
1
NC_1
BST_CTL DVB_S OPT
BST_CNTL 2 S2_SDA EU_F/NIM ADJ/GND 1 0.1uF
+3.3V_S2_DE
10uF 0.1uF
2
+B1[5V] +B1[5V] 36 R9184 0 CN DVB_S DVB_S 10V DVB_S
3 3 DVB_S
4
NC_2[RF_AGC]
NC_1[RF_AGC] DVB_S +3.3V_S2_DE
5
NC_3 4 GND_2 L9102
6
SCLT NC_2 37 Close to the tuner
C9187 C9188
MLB-201209-0120P-N2
SDAT
5 10uF 0.1uF
7 C9124 C9128 C9132
8
NC_4
6
SCLT S2_LNB 100pF 0.1uF 10uF 10V 16V
9
SIF
SDAT
38 50V
DVB_S
16V
DVB_S
10V
DVB_S
DVB_S DVB_S DVB_S C9143 C9146
NC_5 7 10uF 0.1uF
10 +3.3V_S2_TU 10V
VIDEO NC_3 DVB_S
11 8 DVB_S
12
GND
SIF
39 L9103
+B2[1.2V] 9
13
Surge protectioin MLB-201209-0120P-N2
+B3[3.3V] NC_4
14
10 Close to Tuner #38 pin
RESET
15
VIDEO C9144 C9147
16
+B4[2.5V]
11 DVB_S
17
SCL
GND
SHIELD 10uF 0.1uF
SDA 12 LNB_OUT 10V 16V
18 IF_N C9109 C9112 D9101 R9107 DVB_S
ERR +B2[1.2V] C9106 DVB_S
19 13 33pF 33pF 3.0SMCJ20A(suzhougrande) 2.2K
SYNC
IF_P 1000pF OPT DVB_S DVB_S
20 +B3[3.3V] DVB_S
VALID 14 50V
21 6432
MCL RESET DVB_S
22
15 IF_AGC
D0
23
D1
IF/AGC +5V_Normal +5V_TU +3.3V_Normal +3.3V_TU
24 16
25
D2
DIF_1[N] TU_RESET_SUB
D3 17
26
RF_SWITCH_CTL_2 L9108 L9107
D4 DIF_2[P]
27 18 MLB-201209-0120P-N2 MLB-201209-0120P-N2
D5
28

29
D6 RF_SWITCH_CTL
19
30
D7 C9158 C9152 C9160 C9162 C9116 C9149 C9155 C9159 C9161
31
SHIELD TW9910_RESET 22uF 0.1uF 22uF 0.1uF 22uF 0.1uF 22uF 0.1uF 0.1uF
SHIELD
16V 16V 16V 16V 16V 16V 16V 16V 16V
CN

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM35230
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LV7 AU TUNER 91

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 AV1 JACK NON SCART
22 R9202
AV2_R_IN
1/10W
D9201 5%
R9201 C9201 C9202
AMOTECH
5.6V 470K 560pF 560pF
50V 50V

SC_CVBS_IN
22 R9205
AV2_L_IN
D9202 1/10W ATV_OUT
AMOTECH R9203 5% C9204
JK9201 C9203
5.6V 470K 560pF
560pF
PPJ233-01 50V 50V SC_CVBS_IN
5C [RD]E-LUG
+3.3V_Normal
DTV_ATV_SELECT
4C [RD]O-SPRING
R9204
2.7K
3C [RD]CONTACT DTV/MNT_V_OUT
AV2_CVBS_DET
R9206
[WH]C-LUG 1K SC_FB
4B
D9203

[YL]CONTACT 5.6V
3A
1% SC_ID
4A [YL]O-SPRING 10 R9208
AV2_CVBS_IN
D9204 C9205 SC_RE1
5A [YL]E-LUG R9207
5.1V 75 47pF
50V
D9205
SC_RE2
5.1V

SCART_MUTE

SCART1_Lout_N

SCART1_Lout_P

SCART1_Rout_N

SCART1_Rout_P

INCM_VID_SC

AV2/COMP JACK PACK

22 R4006
AV1_R_IN
1/10W
D4009 5%
R4018 C4013 C4022
AMOTECH
5.6V 470K 560pF 560pF
50V 50V

22 R4007
AV1_L_IN
D4008 1/10W
AMOTECH R4019 5% C4023
JK4001 C4014
5.6V 470K 560pF
560pF
PPJ238-01 50V 50V

6C [RD1]E-LUG
+3.3V_Normal

5C [RD1]O-SPRING
R4017
2.7K
4C [RD1]CONTACT
AV1_CVBS_DET
R4023
[WH1]O-SPRING 1K
5B
D4007

[YL1]CONTACT 5.6V
4A
1%
5A [YL1]O-SPRING 10 R4030
AV1_CVBS_IN
ZD4009 C4012
6A [YL1]E-LUG R4016
5.1V 75 47pF
50V
ZD4010
6H [RD2]E-LUG
5.1V
BLM18PG121SN1D
5H [RD2]O-SPRING_2 L4006 22 R4032
SC/COMP2_R_IN

4H [RD2]CONTACT D4010 R4024

470K C4015
560pF C4020
5.6V
50V 560pF
5G [WH2]O-SPRING
50V

5F [RD2]O-SPRING_1
BLM18PG121SN1D
L4007 22 R4033
[RD2]E-LUG-S SC/COMP2_L_IN
7F
D4011 R4025 C4016
[BL2]O-SPRING 560pF C4021
5E 470K
5.6V 50V 560pF
50V
7E [BL2]E-LUG-S
L4001
R4020 1% CM2012FR27KT
4D [GN2]CONTACT 0 10 R4034
SC_R/COMP2_Pr
ZD4011
5D [GN2]O-SPRING C4001 C4002
5.1V R4026
75 27pF 27pF
ZD4012 50V 50V
6D [GN2]E-LUG
5.1V

L4002
R4021 1% CM2012FR27KT
0 10 R4035
SC_B/COMP2_Pb
ZD4013
5.1V R4027 C4003 C4004
75
27pF 27pF
ZD4014 50V 50V
5.1V

L4003-*1
COMP_EU CM2012FR10KT
L4003
R4022 1% CM2012FR27KT COMP_NON_EU
0 10 R4036
SC_G/COMP2_Y
ZD4015 C4005 C4006
5.1V COMP_NON_EU COMP_NON_EU
27pF 27pF
R4028 C4005-*1 50V 50V C4006-*1
ZD4016 75 COMP_EU COMP_EU
47pF 47pF
5.1V
50V 50V
FOR EMI

+3.3V_Normal

R4029
2.7K

1K R4031
SC_DET/COMP2_DET

D4012
5.6V

CLOSE TO JUNCTION

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Repair Guide for ALEF BCM Chassis

Model : 32/37/42/47/55LV3730-TD

FEB. 19th, 2011 LG Electronics/ LCD TV

By [Link]

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Types of LED - Edge
Benefit: More Clear More Real 

Feature

Edge Type Edge LED Best picture quality + thin TV

w/ Local Dimming

LED Array
Upper
Metal
BLU Cover

structure
Model

LED Array is on the side of Module **LV37*0-T*

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Main PCB for Broadband
**LV37*0-T*

To PSU

To Speaker

To T-CON
1 Main processor, DDR Memory
BOARD 1
Flash Memory

2 Micom for Key/IR sensing

2 3 HDMI switch (3:1)

Soft touch +IR
3
4 Audio AMP (10W+10W)

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 BCM35230 Block Diagram

SYSTEM
NAND DDR3 X 16 X 2
Flash(8Gb) (2Gb)

SYSTEM EEPROM X 1
(1Mb)
DIF(+/-)
DVB-T
RF Demod
TUNER CVBS(M)
CVBS
(DVB-T) SIF AUDIO

Side 51P

LVDS.
USB
USB

Audio
(HDCP I2S Out AMP
HDMI1
HDMI HDMI EEPROM)
HDMI2 S/W IC S/W Audio
HDMI3 AMP

H/P L/R Out

BCM
A/V1 CVBS 35230
A/V2 CVBS I2C Sub Micom
(NEC)
COMP1 COMP

PC-RGB Rear RGB,H/V

I2C

PC-AUDIO L/R In

OPTIC SPDIF OUT

M-Remote
UART Module
LAN Ethernet

RS-232C

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Jack Interface

SPDIF

[SPDIF_OUT]

COMP1 BCM35230 AV1

COMP_Y R
[COMP1_Y] [AV1_R_IN]
COMP_PB [AV1_L_IN] L
[COMP1_Pb]
COMP_PR
[COMP1_Pr] [AV1_CVBS_IN] CVBS
[AV1_CVBS_DET]
COMP DET [COMP1_DET] AV DET

AV2
DSUB_R / G / B [DSUB_R+/G+/B+] R
[AV2_R_IN]
DSUB_ V / HSYNC
[DSUB_V/H SYNC] [AV2_L_IN] L

RGB_DDC_SCL [RGB_DDC_SCL] [AV2_CVBS_IN]

EDID EEPROM CVBS
[RGB_DDC_SDA]
AT24C02BN-10SU-1.8 RGB_DDC_SDA [AV2_CVBS_DET]
[BSC_S_SCL] AV DET
[BSC_S_SDA]
[EDID_WP] MICOM
RGB DET
[DSUB_DET] // GPIO

[PC_L_IN]
[PC_R_IN]
PC L,R

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Interconnection - 1
32LV3730-TD [PCBs]

1 Main PCB

2 LED driver

3 Soft Touch + IR Key PCB

1
2 4 PSU
5

4
1 [Cables]
3 2
1 Main / PSU cable

2 Main / Module LVDS cable 51PIN

3 LED driver / PSU

15pin IR/Touch Cable
4 4
(W/ Tube)
3
5 Speaker Cable

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Interconnection - 1
37LV3730-TD [PCBs]

1 Main PCB

2 LED driver

3 Soft Touch + IR Key PCB

1
4 PSU
2

5
4 3
1 [Cables]

1 Main / PSU cable

2
2 Main / Module LVDS cable 51PIN

3 LED driver / PSU

4 15pin IR/Touch Cable
3 4
(W/ Tube)

5 Speaker Cable

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Interconnection - 1
42LV3730-TD [PCBs]

1 Main PCB

2 LED driver

3 Soft Touch + IR Key PCB

2 1

4 PSU
4
5
1
[Cables]

3
1 Main / PSU cable
2
2 Main / Module LVDS cable 51PIN

3 LED driver / PSU

15pin IR/Touch Cable
4
4 (W/ Tube)
3
5 Speaker Cable

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Interconnection - 1
47LV3730-TD [PCBs]

1 Main PCB

2 No exist
4
3 Soft Touch + IR Key PCB
1
4 PSU
3

6 1 [Cables]

1 Main / PSU cable

2
2 Main / Module LVDS cable 51PIN

3 Main / PSU (Inverter)

3 5 4 Module / PSU

5 15pin IR/Touch Cable

(W/ Tube)
6 Speaker Cable

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Interconnection - 1
55LV3730-TD [PCBs]

1 Main PCB

2 No exist
4

3 Soft Touch + IR Key PCB

4 PSU
3
1
4

6 [Cables]
1
1 Main / PSU cable
2
2 Main / Module LVDS cable(51/41)
5
3 Main / PSU (Inverter)

3 4 Module / PSU

5 15pin IR/Touch Cable

(W/ Tube)
6 Speaker Cable

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Interconnection – sub PCB( LV37 Series )

3 Soft Touch + IR PCB

SPK unit

Soft Touch
IR Key PCB
Connected by
15 Pin Cable

To Main

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Contents of LCD TV Standard Repair Process
No. Error symptom (High category) Error symptom (Mid category) Page Remarks

1 No video/Normal audio P-1

2 No video/No audio P-2

3 A. Video error Video error, video lag/stop P-3

4 Color error P-4

Vertical/Horizontal bar, residual image, light

5 P-5
spot, external device color error
6 No power P-6
B. Power error Off when on, off while viewing, power auto
7 P-7
on/off
8 No audio/Normal video P-8
C. Audio error
9 Wrecked audio/discontinuation/noise P-9

10 No response in remote controller, key error,

D. Function error P-10
11 recording error, memory error

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process

Established
LCD TV Error A. Video error date
symptom
No video/Normal audio Revised date P-1

☞A-1-1 ☞A-1-3
Replace Main Board
No video Normal Y Check Back Light Y Check Power Normal Y
Normal audio On OR
audio On with naked eye Board voltage
12v,5v etc.
Replace T-con
N N N Board or module
Move to No Check Power Board 24v output
video/No audio ☞A-1-2 Repair Power
Board or parts

Normal
voltage

N
Repair Power
Board or parts End

※Precaution ☞A-1-4

Always check/record S/W Version and White

Balance value before replacing the Main Replace Main Board Re-enter White Balance value
/Digital Board

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process

Established
LCD TV Error A. Video error date
symptom
No video/No audio Revised date P-2

☞A-1-5
Check various Check and
Normal Y
No Video/ voltages of Power replace
No audio Board voltage?
MAIN B/D
( 5V,12V,24V…)
N End

Replace Power
Board and repair
parts

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error A. Video error
LCD TV symptom
date
Video error, video lag/stop Revised date P-3

* Check point
1) Digital signal disconnected?
2) Analog video signal weak?

☞A-2-1 ☞A-2-2
Y Case 1)
※ Check antenna Normal
Check S/W
Version N Replace Main
End
signal Version B/D
signal? exists?
- Check Signal
Strength and Quality N
Y
Case 2)
Check and fix Connect external device RF signal S/W Upgrade
※ Digital signal
cable
measuring device or
digital ANT signal/connect
※ Check expert mode or
with user remote
controller Check and Normal N
Y
Normal fix ANT screen?
screen? signal
(Request to Y
cable/antenn
N a provider) End

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
Established
Error A. Video error date
LCD TV symptom
Color error Revised date P-4

☞A-4-1 ☞A-3-1
※ Check
Check color by input Y and replace
-External Input Y Y
Color Link Cable Color Color
-COMPONENT Replace Main B/D Replace Main B/D
error? (LVDS) and error? error?
-RGB
contact
-HDMI/DVI
N condition N N

Check error End

color input
mode

Use Picture Test External

Check Y
External Input/ Device /Cable Replace Main B/D
external
Component normal
device and
error
cable N
Color
error? Request repair
for external
Y device/cable
N
Replace Main B/D Y
RGB/ Check external External
device and Device /Cable Replace Main B/D
HDMI/DVI
error cable normal
N
Color End
error?

Replace module
 Standard Repair Process
Established
Error A. Video error date
LCD TV symptom
Vertical/Horizontal bar, residual image, Revised date P-5-1
light spot, external device color error

Vertical/Horizontal bar, residual image, light spot

Use Picture Test

Y Y
Color Replace Main B/D Color Replace
error? error? module

N
N

End

Check color condition by input ☞A-4-1

-External Input Y Y
Screen Check external Check and Screen N
-Component Normal?
normal? device replace Link normal? Replace Main B/D
-RGB
connection Cable
-HDMI/DVI
condition N
N
Y
Replace Request
module End
repair for
Check Test mode external
RGB screen device

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error A. Video error date
LCD TV symptom
Vertical/Horizontal bar, residual image, Revised date P-5-2
light spot, external device color error

Vertical/Horizontal bar, residual image, light spot

Check color condition by input ☞A-4-1

-External Input Y Y
Screen Check external Check and Screen N
-Component Normal?
normal? device replace Link normal? Replace Main B/D
-RGB
connection Cable
-HDMI/DVI
condition N
N
Y
Replace Request
module End
repair for
Check Test mode external
RGB screen device

External device screen error-Color error

Check screen
condition by
N External
Check S/W Version Check input Connect other external
Input N
version -External Input device and cable Screen
error Replace
-Component (Check normal operation normal?
-RGB Main B/D
Y of External Input,
-HDMI/DVI Component Component, RGB and
Y
S/W Upgrade error HDMI/DVI by connecting
Jig, pattern
Request repair for
Generator ,Set-top Box
external device
etc.
RGB Y
error Connect other external
Normal N
device and cable N
screen? (Check normal operation Screen
normal? Replace Main B/D
of External Input,
Y HDMI/ Component, RGB and
DVI HDMI/DVI by connecting
Jig, pattern
End
Generator ,Set-top Box etc.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error B. Power error date
LCD TV symptom
No power Revised date P-6

☞B-1-1 ☞B-1-3 ☞B-1-3

Check Power
Check ST-BY Red lamp Y Normal N Check Power Y Replace
On Key OK?
(Lamp) display operation? On ‘”H” Power
operation B/D
N Y N

Check AC Replace Main B/D

cord
connection ☞B-1-4
and voltage
Measure voltage of each output of Power B/D

Normal Y
Replace Main B/D
☞B-1-2 Y voltage?
Normal Y Normal
voltage? Check ST-BY 3.5V Y
voltage? N

Replace Power B/D

N N

Check and fix outlet and power cord connected condition

Replace Power
B/D

※ For Pacific 2, operation display LED can be off even with ST-BY output of 3.5V
→ In this case, replace the Digital B/D instead of the Power Board

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error B. Power error date
LCD TV symptom
Off when on, off while viewing, power auto on/off Revised date P-7

Check outlet

☞B-2-1
N
Check A/C code Error? Key Time Y
Check Power Off Replace Main B/D Normal? End
Mode Out

N
Check for 3 wave length
Y CPU
Replace Power B/D
Abnormal

Fix A/C code/Outlet Describe

On 15
and describe 3 Reset Off mode situation
Minute
wave length Not a problem

※ If there is
no signal, it is
the 15 min
☞B-2-2 OFF function

(If Power Off mode

Normal Y
is not displayed) Replace Main B/D
voltage?
Check Power B/D
voltage
N
* Caution
Check and fix exterior
Replace Power B/D
of Power B/D/Part

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error C. Audio error date
LCD TV symptom
No audio/Normal video Revised date P-8

☞C-1-1 ☞C-1-3
Check user N
N Use Sound Normal Check audio Normal N Replace Power
No audio menu item Off Test Menu Sound B+24V of Power voltage Board and
Screen normal Speaker off Board repair parts
Y Y Y

Cancel OFF and describe Check Input Signal

N Check
End Replace MAIN Disconnection Speaker
Board
disconnectio
Y n

Replace Speaker

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error C. Audio error date
LCD TV symptom
Wrecked audio/discontinuation/noise Revised date P-9

→ Wrecked audio/discontinuation/noise is same after “Check input signal” compared to No audio

☞C-1-3
Wrecked audio/ Check and
Discontinuation/ Check audio
replace speaker
Noise for B+Voltage (24V)
and connector
Check input all audio
signal
Signal Y Y
-RF
-External normal? Wrecked audio/
Normal
Input signal Discontinuation/ Replace Main B/D
N voltage?
Noise only
for D-TV
N
Wrecked audio/
Discontinuation/
Replace Power B/D
Noise only
for Analog
(When RF signal is not
received)
Wrecked audio/ Replace Main B/D End
Request repair to
external cable/ANT Discontinuation/
provider Noise only
for External Input
(In case of N
External Input Connect and Normal
signal error) check other audio?
Check and fix external device
external device Y

☞A-2-1, A-2-2 Check and fix external device

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process
Established
Error D. Function error date
LCD TV symptom
No response in remote controller, Revised date P-10
key error

☞ D-1-1 ☞ D-1-1 ☞ D-1-3

N Check Cable Check Assemble Y Check N
IR work Assemble Correct Replace
Connection State of 3.5V and 5V
correctly? Correctly? 3.5V and 5V? Main B/D
(Touch PCB / Touch PCB of IR Terminal
MB)
Y N Y

Replace Touch PCB

Check Assemble
W/ Front Cabinet
State of Touch ☞ D-1-2
PCB Cable

Y Check Touch
Assemble If Touch Touch PCB Y
Value and Correct Replace Touch PCB
Correctly? Touch : Over 10
Threshold Value? W/ Front Cabinet
THR : 6 of 7 (default)
N
☞ D-1-4 N
Replace Touch PCB
W/ Front Cabinet Adjust THR Value
Min : 5 / MAX 25
5 is most Sensitive

Work correctly?

END

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Contents of LCD TV Standard Repair Process Detail Technical Manual

Error symptom Content Page Remarks

No.
1 Check LCD back light with naked eye A-1-1

2 LED Driver B+ 24V measuring method A-1-2

3 A. Video error_ No video/Normal audio Check LED Driver PCB supply voltage A-1-3

4 Check White Balance value A-1-4

5 Power Board voltage measuring method A-1-5

TUNER input signal strength checking method A-2-1

7 A. Video error_ No video/Video lag/stop
LCD-TV Version checking method A-2-2

Check Link Cable (LVDS) reconnection condition A-3-1

10 A. Video error_Color error
Use Picture Test Mode A-3-2

LCD TV connection diagram (09) A-4-1

A. Video error_Vertical/Horizontal bar,
13 Use Picture Test Mode A-4-2
residual image, light spot
Check Link Cable (LVDS) reconnection condition A-4-3

15 Check front display LED B-1-1

16 Check power input voltage and ST-BY 3.5V B-1-2

B. Power error_No power
17 Checking method when power is ON B-1-3

18 POWER BOARD voltage measuring method B-1-4

Continue to next page

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Contents of LCD TV Standard Repair Process Detail Technical Manual
Continued from previous page

No. Error symptom Content Page Remarks

19 B. Power error_Off when on, off while POWER OFF MODE checking method B-2-1

20 viewing POWER BOARD PIN voltage checking method B-2-2

Checking method in menu when there is no
22 C-1-1
audio
C. Audio error_No audio/Normal video Voltage and speaker checking method when
23 C-1-2
there is no audio
24 Use Sound Test Mode C-1-3
C. Audio error_Wrecked Voltage and speaker checking method in case
25 C-2-1
audio/discontinuation of audio error
Check Cable Connection D-1-1

D. Function error_ No response in remote Check Assemble state of Touch PCB D-1-2
29
controller, key error Check 3.5V and 5V of IR Terminal D-1-3

Check Touch Value and Threshold D-1-4

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error_No video/Normal audio Established
LCD TV symptom date
LED Driver B+ 24V measuring method Revised
Content A-1-2
date

Measure the DC 24V supplied to LED Driver from the Power Board.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error_No video/Normal audio Established
LCD TV symptom date
Check LED Driver PCB supply voltage Revised
Content A-1-3
date

24V is provided from the Power Board and supplied to LED Check each voltage output (5V,12V,24V) in the Power Board.
Driver PCB. Check the PIN contact condition and connection.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error_No video/Normal audio Established
LCD TV symptom date
Content Check White Balance value Revised
A-1-4
date

Entry method

1. Press the ADJ button on the remote controller for adjustment.

2. Enter into White Balance of item 9.

3. After recording the R, G, B (GAIN, Cut) value of Color Temp

(Cool/Medium/Warm), re-enter the value after replacing the MAIN BOARD.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error Established
LCD TV symptom
A. Video error_No video/No audio date
Revised
Content Power Board voltage measuring method date A-1-5

Check each voltage output

(3.5V, 12V, 24V) supplied
from Power Board to Main
Board.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error Established
A. Video error_Video error, video lag/stop
LCD TV symptom date
Revised
Content TUNER input signal strength checking method date A-2-1

Check MENU -Æ SETUP -Æ Support -Æ Signal Test Check Signal Strength and Quality

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error_Video error, video lag/stop Established
LCD TV symptom date
Revised
Content LCD-TV Version checking method date A-2-2

1. Checking method for remote controller for adjustment

Version

Press the IN-START with the * Press the Menu button on the
remote controller for adjustment remote controller
Enter Auto Channel
Press the number button 1,1,1,1,1
HOST menu is displayed on the
screen.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error_Color error Established
LCD TV symptom date
Revised
Content Use Picture Test Mode A-3-2
date

Menu -> Support -> Picture Test Test Image

Entry method

1. Press the Menu button on the remote controller

2. Enter into Support -> Picture Test

3. The TV Display Test Image

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error _Vertical/Horizontal bar, Established
LCD TV symptom residual image, light spot date
LCD TV connection diagram (09) Revised
Content A-4-1
date

As the part connecting to

the external input, check
the screen condition by
signal

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error A. Video error _Vertical/Horizontal bar, Established
LCD TV symptom residual image, light spot date
LCD TV connection diagram (09) Revised
Content A-4-2
date

Menu -> Support -> Picture Test Test Image

Entry method

1. Press the Menu button on the remote controller

2. Enter into Support -> Picture Test

3. The TV Display Test Image

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error Established
B. Power error _No power
LCD TV symptom date
Check front display LED Revised
Content B-1-1
date

ST-BY condition: Red

Power ON condition: Blue

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error Established
B. Power error _No power
LCD TV symptom date
Check power input voltage and ST-BY 3.5V Revised
Content B-1-2
date

②
①

Power checking method

1. Check the AC220V input in the power cord.
2. Check the connected part with input from the POWER BOARD and whether the fuse is connected.
3. Check the ST-BY DC 3.5V output voltage from the POWER BOARD.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error B. Power error _ No power Established
LCD TV symptom date
Checking method when power is ON Revised
Content B-1-3
date

① ②

Checking method when power is ON

1. Check the ST-BY DC 3.5V output voltage from Soft Touch PCB Test Point T6
2. Check the operating condition of the power KEY on the Soft Touch PCB (Test Point P4, T5)
3. Check the AC-DET (AC) DC3.5V voltage on POWER BOARD.
4. Check the POWER ON High (About DC 1.8V or above) voltage with input from POWER BOARD.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error B. Power error _ No power Established
LCD TV symptom date
Content POWER BOARD voltage measuring method Revised
B-1-4
date

24V is provided from the Power Board and supplied to LED Check each voltage output (5V,12V,24V) in the Power Board.
Driver PCB. Check the PIN contact condition and connection.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error B. Power error _ Off when on, off whiling viewing Established
LCD TV symptom date
POWER OFF MODE checking method Revised
Content B-2-1
date

Entry method

1. Press the IN-START button of the remote

controller for adjustment

2. Check the entry into adjustment item 3

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error B. Power error _ Off when on, off whiling viewing Established
LCD TV symptom date
POWER BOARD PIN voltage checking method Revised
Content B-2-2
date

Check the voltage when the

Power OFF mode is not
shown

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error C. Audio error_ No audio/Normal video Established
LCD TV symptom date
Content Checking method in menu when there is no audio Revised
C-1-1
date

Checking method
1. Press the MENU button on the remote controller
2. Select the AUDIO function of the Menu
3. Select TV Speaker from Off to On

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error C. Audio error_ No audio/Normal video Established
LCD TV symptom date
Content Use Sound Test Mode Revised
C-1-2
date

Menu -> Support -> Sound Test Sound Test (Play the Music)

Entry method

1. Press the Menu button on the remote controller

2. Enter into Support -> Sound Test

3. The TV Play the Test Music

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error Established
LCD TV symptom C. Audio error_ No audio/Normal video
date
Voltage and speaker checking method Revised
Content C-1-3
when there is no audio date

① ② ③

Checking order when there is no audio

① Check the contact condition of 24V connector of Main Board

② Measure the 24V input voltage supplied from Power Board (If there is no input voltage, remove and
check the connector)

③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you
touch the GND and output terminal, the speaker is normal.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error Established
LCD TV symptom C. Audio error_ Wrecked audio/discontinuation/noise date

Content Voltage and speaker checking method in case of audio error Revised
date C-2-1

① ② ③

Checking order when there is no audio

① Check the contact condition of 24V connector of Main Board

② Measure the 24V input voltage supplied from Power Board (If there is no input voltage, remove and
check the connector)

③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you
touch the GND and output terminal, the speaker is normal.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error D. Function error_ No response in remote controller, Established
LCD TV symptom key error date
Revised
Content Check Cable Connection D-1-1
date

1. Check Connection state of Main Board.

2. Check Connection state of Touch PCB
3. Check Cable and Connection State

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error D. Function error_ No response in remote controller, Established
LCD TV symptom key error date
Revised
Content Check Assemble state of Touch PCB D-1-2
date

1. Remove Cable of Touch BCB

2. Remove Touch PCB Cover carefully
3. Check Asseble state of Touch PCB
4. Keep the guide of right side

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error D. Function error_ No response in remote controller, Established
LCD TV symptom key error date
Revised
Content Check 3.5V and 5V of IR Terminal D-1-3
date

1. ① 1. ②

1. Check the DC 5V on the 3.5V_ST terminal. (Pin 6)

2. When checking the Pre-Amp when the power is in ON condition, it is normal
when the Analog Tester needle moves slowly, and defective when it does not
move at all.
3. Input voltage terminal: 3.5V_ST (Pin 6)
4. Remote controller receiver terminal: IR (Pin 9)

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Standard Repair Process Detail Technical Manual
Error D. Function error_ No response in remote controller, Established
LCD TV symptom key error date
Revised
Content Check Touch Value and Threshold D-1-4
date

1. Press the ADJ Button on the remote controller for adjustment.

2. Check THR Value (Default : 6/7/7/7/6/7/7/7) (THR range is 5~25, 5 is most
sensitivity)
3. When touch the Touch PCB, and Touch value must lager than 10
4. IF Touch value is less than 10, adjust THR Value.

Copyright © 2011 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes