Data Sheet PIPOLYIIENa

Poly-Fine® II Series
Filter Cartridges

Prefilter for Final Membrane Applications

• Proprietary filter media produced by Pall for highly
consistent performance
• High contaminant-holding capacity
• Wide chemical compatibility
• Rigid polypropylene outer cage protects filter
• All polypropylene one piece construction
(except 0.2 micron)
• Asymmetric polysulfone media used in 0.2 µm grade
• Fast rinse-up to 18 Megohm-cm

Performance Specifications
Filter grades
0.2, 0.25, 0.45, 0.8, 2, 3, 5, 10, 30, 50, 100 µm

Recommended change-out differential pressure1

2.4 bard (35 psid)

Maximum forward differential pressure

4.8 bard (70 psid) @ 20°C (68°F) Product Specifications
2.8 bard (40 psid) @ 65°C (150°F) Materials of construction
Food and water contact use Filter media:
Please contact Pall Corporation to verify that the product PFT 0.2: Highly asymmetric polysulfone
conforms to your national legislation and/or regional All other grades: Polypropylene
regulatory requirements for water and food contact use. Hardware: Polypropylene
Sealing: Thermal bond
Cartridge rinse-up Support material: Polypropylene
Rinse-up to 18 Megohm-cm with a minimum of throughput. Gaskets/O-rings: Silicone elastomer, nitrile, EPDM,
Purity fluorocarbon elastomer, white nitrile,
Cartridges are free of resins, binders, and adhesives. white silicone, expanded PTFE, FEP
encapsulated silicone, high purity
Sterilization: fluorocarbon elastomer, FEP
Multiple autoclaving for 30 minutes at 121°C (250°F) encapsulated fluorocarbon elastomer,
under no end load conditions. In-line steam sterilization Kalrez2, white neoprene
is not recommended. May be in-line sanitized with hot
water at 82°C (180°F) for 1 hour. Dimensions (nominal)
Outside diameter: 6.6 cm (2.6 in)
Lengths: 10.2 cm (4 in), 24.8 cm (9.75 in),
25.4 cm (10 in), 49.5 cm (19.5 in),
1 Provided that the maximum differential pressure is not exceeded based
50.8 cm (20 in), 74.3 cm (29.25 in),
on temperature limits defined above. 76.2 cm (30 in), 99.1 cm (39 in),
2 Registered trademark of DuPont Dow.
102 cm (40 in)
Particle Retention (µm)
Liquid Service Gas Service
(by ASTM F-795 Test)
Cartridge 90% >99.9% Removal Efficiency
Designation Efficiency Efficiency By DOP Test
PFT 0.2 0.2 0.5 99.99%
PFT 0.25 0.25 1.0 99.97%
PFT 0.45 0.45 1.2 99.93%
PFT 0.8 0.8 2.5 99.90%
PFT 2.0 2 5 _______
PFT 3.0 3 7 _______
PFT 5.0 5 12 _______
PFT 10.0 10 15 _______
PFT 30.0 30 40 _______
PFT 50.0 50 65 _______
PFT 100.0 85 100 _______

Typical Flow vs. Differential Pressure for Application

Sizing

Flow rate (lpm), water at 20°C

0 10 20 30
.5
0.2 µm
0.25 µm 0.45 µm
.45
0.03
.4
Differential pressure (bard)
Differential pressure (psid)

.35 0.8 µm

.3 2 µm 0.02
.25
.2
.15 3 µm 0.01
5 µm
.1 10 µm
30 µm
.05
50 µm, 100 µm
0
0 2 4 6 8 10
Flow rate (gpm), water at 68°F

Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water,
multiply differential pressure by fluid viscosity (cP).

Unit conversion: 1 bar = 100 kPa

Ordering Information
Pall Part Number = PFT 1 – 2 U 3 – 4 5 6 – 7

Table 1 Table 3 Table 4

Code Filter Code Gasket/O-ring Code End configurations
grades (µm) materials
Blank DOE industrial
0.2 0.2 S Silicone
1X DOE industrial, 2.54 cm (1 in) extended core
0.25 0.25 N Nitrile M2 SOE flat closed end, fits housings with
0.45 0.45 M White silicone 020 O-ring post
0.8 0.8 W White nitrile M3 SOE flat closed end, external 222 O-rings
(gaskets) (retrofits other manufacturers’ Code 0) 3
2 2
V Fluorocarbon M3H SOE large diameter closed end, external
3 3 222 O-rings
elastomer
5 5 M4 SOE fin end, external 222 O-rings with
E EPDM
10 10 locking tabs
T FEP encapsulated
M5 DOE, internal 120 O-rings
30 30 silicone (O-rings) (retrofits 213 O-ring style) 3
50 50 T Expanded PTFE M6 SOE flat closed end, external 226 O-rings
(gaskets) (retrofits other manufacturers’ Code 6) 3
100 100
X No O-ring required M7 SOE fin end, external 226 O-rings
(M2 style only) (retrofits other manufacturers’ Code 7) 3
Table 2
F FEP encapsulated M8 SOE fin end, external 222 O-rings
Code Cartridge fluorocarbon (retrofits other manufacturers’ Code 5) 3
lengths (cm / in) elastomer (O-rings)
nominal M10 DOE, internal O-rings (fits other manufacturers’
K Kalrez (222 O-rings) housings) 3
4 10.2/4
Q High purity M11 SOE flat closed end, internal 120 O-ring
9.75 24.8/9.75 fluorocarbon (retrofits other manufacturers’ X style) 3
10 25.4/10 elastomer M18 SOE flat closed end, external 222 O-ring
(222 O-rings)
19.5 49.5/19.5 M20 SOE, internal O-ring (same as M10),
Z White neoprene closed end with deep recess
20 50.8/20 (gaskets)
M22 SOE fin end, external 225 O-ring
29.25 74.3/29.25 3 For details, contact Pall Corporation.
30 76.2/30 Table 5
39 99.1/ 39
Code Bubble test option
40 101.6 /40
Blank No bubble test
B 100% bubble best

Table 6 Table 7
Code Pre-rinse option Code Packaging
Blank No pre-rinse Blank Standard
packaging
414 100% pre-rinse
-BLK Bulk packaging

25 Harbor Park Drive Visit us on the Web at www.pall.com

Port Washington, NY 11050
Pall Corporation has offices and plants throughout the world. For Pall representatives in your
+1 516 484 3600 telephone area, please go to www.pall.com/contact.
+1 800 289 7255 toll free US
Please contact Pall Corporation to verify that the product conforms to your national legislation
and/or regional regulatory requirements for water and food contact use.
Portsmouth – UK
+44 (0)23 9230 3303 telephone Because of technological developments related to the products, systems, and/or services
+44 (0)23 9230 2507 fax described herein, the data and procedures are subject to change without notice. Please
consult your Pall representative or visit www.pall.com to verify that this information remains
www.pall.com/contact valid.

© Copyright 2012, 2019, Pall Corporation. Pall, and Poly-Fine are trademarks of Pall Corporation. ® Indicates a
trademark registered in the USA. Filtration. Separation. Solution.SM is a service mark of Pall Corporation.

PIPOLYIIENa Produced in the USA January 2019