TECHNICAL SPECIFICATION:

Cat. No.: MD71B9 MD71BH MD71BF MG73B9 MG73BH MG73BF MG73BR MGH3BH MGI3BF MG73BQ
SUPPLY MONITORING DEVICE
Function Phase and Voltage Control
SERIES SM500
Reference Supply Voltage ( ) 120 to 240
1-Phase or 3-Phase 4-Wire
240 VAC 220 VAC 230 VAC
settable
1-PHASE AND 3-PHASE 4-WIRE
Frequency 47 to 63 Hz
Power Consumption 4 VA (Max.)
Under Voltage 55% to 95% of 173 V ± 10 V 55% to 95% of 80% of
288 V ± 10 V
Trip Levels Over Voltage 105% to 125% of 105% to 125% of RoHS
Asymmetry N.A. 10% 20% ± 4%, 10% 10 % of
Hyst. 4%±2%) Hyst. 2.7 %
Setting Accuracy +/- 5% of full scale (Voltage setting are with respect to neutral)
Power ON Delay < 500 msec
Setting Accuracy On Delay 0 - 15 min 0.5 - 15 s 5 s fixed 0 - 15 min 0.5 - 15 s 5 s fixed 0.5-10 s ±1s 0.5 - 15 s 5 s fixed Cat. No.:
±10% of Full
scale Off Delay 5 s fixed 5 s fixed 0 - 15 s 5 s fixed 5 s fixed 0.5 - 15 s 0 .5
- - 5s 5 s fixed 0 - 15 s
Phase Reverse trip time is < 100 ms. For Non-Inductive loads Phase Fail trip time is < 100 ms.
MD71B9
LED Condition / Faults Indications or Status of LED
MD71BH
ON (Green) Power ON Continuous ON MD71BF
UV (RED) Under Voltage Continuous ON MG73B9
OV (RED) Over Voltage Continuous ON MG73BH
High Cut OFF N.A. Blinking N.A. Blinking
MG73BF
Phase Asymmetry N.A. Blinking
ASY / REV (RED) MG73BR
Phase Reverse N.A. Continuous ON
Contact Arrangement 1 C/O 2 C/O (Minimum load of 5mA is recommended)
MGH3BH
Relay Output Contact Rating 5 A (Res.) @ 250 VAC / 28 VDC MGI3BF
Contact Material Ag Alloy MG73BQ
Utilization Category Ue Rated Voltage V 120/240V
AC-15 Ie Rated Current I 3.0/1.5A
Utilization Category Ue Rated Voltage V 24/125/250V
DC-13 Ie Rated Current I 2.0/0.22/0.1A
Mechanical Life Expectancy 3 x 106 Operations
Electrical Life Expectancy 1 x 105 Operations
Operating Temperature -15 ºC to +55 ºC
Storage Temperature -25 ºC to +70 ºC
Humidity (Non-Condensing) 95% (Rh)
Max. Operating Altitude 2000 m
Degree of Protection IP-20 for Terminals ; IP-30 for Housing
Pollution Degree Type II
Housing Flame Retardant UL 94-V0
Mounting Base / Din-Rail (35 mm Symmetrical)
Dimensions in mm (W x H x D) 36 x 60 x 90
Weight (Unpacked) 120 g Approx.
Certifications CE, RoHS
*All LEDs should off incase of Single Phase Loss, 2 Phase Loss & 3 Phase Loss conditions.
MLL022_04
 287.27 mm

60.0
SUPPLY MONITORING DEVICE OPERATING MODES:
MG73BQ
SERIES SM500 Rated voltage ranges 120/220/230/ All products operates in Single Phase as well

(35 MM - SYMMETRICAL)
1-Phase and 3-Phase 4-Wire 240 VAC Un(PH - N) selectable as Three Phase Mode.

DIN RAIL
Output Relay will energize after operate
MAIN FEATURES: time if following conditions are within Three Phase Mode:

100.0 C / C
100.0 C / C
l Adjustable Reference voltage
limit:

90.0
68.0
Connect three phases at L1, L2, L3 and

45.0
1. All phases are present and phase
l Monitors own supply Neutral at N terminal. Keep P terminal open.
voltages are within the over & under
l Phase Loss & Neutral loss detection.
voltage trip levels set on the device.
l Phase Reverse detection Single Phase Mode:
l Phase Asymmetry 10% (Phase to Phase) 2. If Phase Sequence is ok.
l Adjustable Over & Under voltage trip level Connect a link between L1 & P and Neutral
l Adjustable Operate Time & Release Time 3. If Phase to phase asymmetry is less
at N terminal. L2 & L3 connections are don't
l SPDT, DPDT Relay output (5 A, Resistive) than value mentioned in technical
Ø4.2 care. In single phase mode, device monitors
l Din rail & base mounting specification. Ø4.2
36.0
36.0 only L1 phase for UV & OV condition.
l LED indications Relay will trip after release
I nstant trip in case of Interruption, Phase time if any of Phase exceeds over voltage
Reverse and Phase Loss and under voltage trip levels. Note :
FUNCTION DESCRIPTION: Relay will be trip in <100ms if any phase
fail, Line interruption or phase Reverse. The technical information provided in
MD71B9, MD71BH, MD71BF this document is correct at the time of
l Output relay will energize after FOR SINGLE PHASE APPLICATION FOR THREE PHASE APPLICATION going to the press. Product innovation
operate time if all phases are present R N R Y B N being a continuous process, we reserve
& Healthy with in the levels set. 15 15 the right to alter specifications without
L1 P L2 L3 N L1 P L2 L3 N any prior notice.
l Output relay will de-energize SM 500 SM 500 CERTIFICATION :
after release time if any of or all 16 18 16 18
phases exceeds OV or UV trip levels.
IEC 61000-3-2 Ed. 3.2 (2009-04) Class A
FOR SINGLE PHASE APPLICATION FOR THREE PHASE APPLICATION
MG73B9, MG73BH, MG73BF, MG73BR R N
IEC 61000-4-2 Ed. 2.0 (2008-12) Level III
R Y B N
IEC 61000-4-3 Ed. 3.2 (2010-04) Level III
Rated voltage - 240 VAC Un (PH - N) 15 25 15 25 IEC 61000-4-4 Ed. 3.0 (2012-04) Level IV
MGH3BH - Rated voltage - 220 VAC Un (PH - N) L1 P L2 L3 N L1 P L2 L3 N
MGI3BF - Rated voltage - 230 VAC Un (PH - N) SM 500 SM 500 IEC 61000-4-6 Ed. 3.0 (2008-10) Level III
16 18 26 28 16 18 26 28
l Output Relay will energize after operate CISPR 14-1 Ed. 5.2 (2011-11) Class A
time if following conditions are within
CISPR 14-1 Ed. 5.2 (2011-11) Class A
limit: Terminal Details :
1. All phases are present and phase
IEC 60947-5-1 Ed. 3.1 (2009-07) 2 kV
voltages are within the over & under
IEC 60947-5-1 Ed. 3.1 (2009-07) Level IV
voltage trip levels set on the device.
IEC 61010-1 Ed. 3.0 (2010-06) Level IV
2. If Phase Sequence is ok. >50 k

3. If Phase to phase asymmetry is less

MLL022_04