Automotive Chip Choke

EMI Suppression for CAN-Bus Networks

2-Line Common Mode Chokes NETWORK PRODUCTS

Meets AEC-Q200 Requirements

Suppression of common mode noise without attenuating the
signal
Magnetically shielded versions for lower Rdc and higher current
Supports CAN-Bus, A2B and other IVN high speed differential
signal lines (LVDS)

Electrical Specifications @ 25°C

Common Mode Impedance Leakage Isolation Rated
(10MHZ) Inductance Standard RDC IDC
Inductance Resistance Voltage
(uH) Tolerance (Ω Max) (A MAX)
Part Number Min Typ (nH) MAX (MΩ) Min (V) Max
PE-1812ACCXXXSTS Operating Temperature Range -40°C to +125°C
PE-1812ACC110STS 300 600 11 +50/-30% 0.5 45 0.36 10 50
PE-1812ACC220STS 600 1200 22 +50/-30% 0.6 50 0.31 10 50
PE-1812ACC510STS 1500 3500 51 +50/-30% 1 150 0.23 10 50
PE-1812ACC101STS 3000 7500 100 +50/-30% 2 200 0.2 10 50

Mechanical Schematic
2 3 1 4
A
E

C
2 3
view from PCB
PIN 1
B 1 4
D
F
All Units in mm W S
Bifilar winding
(representation only)

Component Dimensions (mm) SOLDER PAD (mm)

Series A B C D E F X T W S
1812 ACC 4.5 +/-0.20 3.2 +/-0.20 3.0 MAX 3.1+/-0.20 0.65+/-0.15 0.70+/-0.15 5.90 3.20 3.40 1.60

1 [Link] W717.I (06/20)

Automotive Chip Choke
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes NETWORK PRODUCTS

Impedance vs Frequency Temp vs DC Current

PE-1812ACC110STS

Common mode Differenal mode ːT@25 ͦC

60.0
10,000

50.0
1,000
11uH 11uH
40.0
Common mode Differenal mode ːT@25 ͦC
Impedance (Ω)

ͦ )
ːT( C
100
60.0
10,000 30.0

10 50.0
1,000 20.0
11uH 11uH
40.0
Impedance (Ω)

ͦ )
1 10.0

ːT( C
100
30.0
0.1 0.0
10 0.0 0.2 0.4 0.6 0.8 1.0
1 10 100 1,000 20.0
Frequency(MHz) IDC(A)
1 10.0

0.1 Common mode Differenal mode 0.0 ːT@25℃

10,000.0 60.0 0.0 0.2 0.4 0.6 0.8 1.0
1 10 100 1,000
PE-1812ACC220STS 22uH
Frequency(MHz) IDC(A)
50.0
1,000.0 22uH

40.0
Impedance( Ω)

Common mode Differenal mode ːT@25℃

ͦ )
ːT( C

100.0
10,000.0 60.0
30.0
22uH
10.0 50.0
1,000.0 20.0 22uH

40.0
Impedance( Ω)

1.0
ͦ )

10.0
ːT( C

100.0
30.0
0.1 0.0
10.0 0.0 0.2 0.4 0.6 0.8
1 10 100 1,000 20.0
Frequency(MHz) IDC(A)
1.0 10.0

0.1 0.0
1 10 100 1,000 0.0 0.2 0.4 0.6 0.8
Frequency(MHz) IDC(A)

2 [Link] W717.I (06/20)

Automotive Chip Choke
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes NETWORK PRODUCTS

Impedance vs Frequency Temp vs DC Current

PE-1812ACC510STS

Common mode Differenal mode

ːT@25℃
100,000.0
70.0

60.0
10,000.0
51uH 50.0
Common mode Differenal mode 51uH
ːT@25℃
Impedance( Ω)

ː T(℃ )
100,000.0 40.0
70.0

30.0
60.0
100.0
10,000.0
51uH 20.0
50.0
51uH
Impedance( Ω)

ː T(℃ )
10.0 10.0
40.0

0.0
30.0
1.0
100.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
1 10 100 1,000
20.0
Frequency(MHz) IDC(A)
10.0 10.0

0.0
1.0 Common mode Differenal mode 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
ːT@25℃
100,000.0 1 10 100 1,000
60.0
PE-1812ACC101STS Frequency(MHz) IDC(A)

10,000.0 50.0
100uH
100uH
Common mode Differenal mode 40.0
ːT@25℃
ͦ )
ːT ( C
Impedance(Ω)

1,000.0
100,000.0
60.0
30.0

100.0
10,000.0 50.0
20.0 100uH
100uH
40.0
ͦ )

10.0
ːT ( C
Impedance(Ω)

10.0
1,000.0
30.0
0.0
1.0
100.0 0.00 0.10 0.20 0.30 0.40 0.50
1 10 100 1,000 20.0

Frequency(MHz) IDC(A)
10.0 10.0

0.0
1.0 0.00 0.10 0.20 0.30 0.40 0.50
1 10 100 1,000
Frequency(MHz) IDC(A)

3 [Link] W717.I (06/20)

Automotive Chip Choke
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes NETWORK PRODUCTS

Reliability Test
Item Reference documents Test Condition Test Specification

1. Temperature: 125�C 1. No mechanical and electrical damage

1. High Temperature Exposure MIL-STD-202 Method 108
2. Time: 1000 hours 2. Inductance shall not change more than ±30%

1. Temperature: -40�C~125�C
1. No mechanical and electrical damage
2. Temperature Cycling JESD22 Method JA-104 2. Number of cycles: 1000 cycle
2. Inductance shall not change more than ±30%
[Link] time: 30 minutes
1. Temperature: 85±5�C
1. No mechanical and electrical damage
3. Biased Humidity Test MIL-STD-202 Method 103 2. Time: 1000 hours
2. Inductance shall not change more than ±30%
3. Humidity: 85±5% RH
1. Temperature: 125�C
1. No mechanical and electrical damage
4. Operational Life MIL-PRF-27 2. Time: 1000 hours
2. Inductance shall not change more than ±30%
3. Apply rated current
Inspect product construction, marking and
5. External Visual MIL-STD-883 Method 2009 Per product specification standard
workmanship
Verify physical dimensions to the applicable product
6. Physical Dimensions JESD22 Method JB-100 Per product specification standard
detail specification
1. No body change in appearance
Immerse into solvent for 3±0.5 minutes & brush 10
7. Resistance to solvents MIL-STD-202 Method 215 2. No marking blurred.
times for their cycles.
3. Inductance shall not change more than ±30%
1. Frequency and Amplified: 10-2000-10 Hz, 1.5mm
2. Direction: X, Y, Z 1. No mechanical and electrical damage
8. Vibration Test MIL-STD-202 Method 204
3. Test duration: 2 hours for each direction, 6 hours 2. Inductance shall not change more than ±30%
in total
1. Temperature: 250±5�C
9. Resistance to Soldering 1. No mechanical and electrical damage
MIL-STD-202 Method 210 2. Time: (temp.≥217�C) 92~109 Seconds
Heat Test 2. Inductance shall not change more than ±30%
3. IR reflow times: 3 times
1. No mechanical and electrical damage
10. Rated Current MIL-STD-202 Method 330 Apply rated current for 5 seconds.
2. Inductance shall not change more than ±30%
1. No mechanical and electrical damage
11. Temperature Rise MIL-PRF-27 Apply rated current for 10 minutes.
2. Inductance shall not change more than ±30%
1. No mechanical and electrical damage
12. Over load MIL-PRF-27 Apply twice as rated current for 5 minutes.
2. Inductance shall not change more than ±30%
1. Bakeing in pre-testing: 150±5�C / 16Hours±30min.
2. Peak temperature: 245�C The terminal shall be at least 95% covered with fresh
13. Solderability Test J-STD-002
3. Time: (temp.≥217�C) 112 Second solder.
4. IR reflow times: 1 time
1. Operating temperature: -40�C~125�C 1. No mechanical and electrical damage
14. Electrical Characterization User Spec.
2. Room Temperature: 25�C 2. Inductance shall not change more than ±30%
1. DV: 500V 1. During the test no breakdown.
15. Withstanding Voltage Test MIL-STD-202 Method 201
2. Time: 1 minute 2. The characteristic is normal after test.
Package & Drop down from 1m. In 1 angle 1 ridge 1. No case deformation or change in appearance.
16. Drop JESD22-B111
& 2 surfaces orientation 2. Inductance shall not change more than ±30%
1. Apply push force to samples mounted on PCB.
17. Terminal Strength Test JIS-C-6429 After test, inductors shall be on mechanical damge.
2. Force of 1.8 kg for 60±1 seconds.

4 [Link] W717.I (06/20)

Automotive Chip Choke
EMI Suppression for CAN-Bus Networks
2-Line Common Mode Chokes

Tape and Reel Specifications

Reel Dimensions (mm) Tape Dimensions (mm)

Series Parts per Reel A B C D E W P1 P2 P3 H T
1812 ACC 500 178 60 13 17 14 12 2 8 4 4 0.35

Recommended Solder Heat Resistance Profile

I. Description:
a. Ferrite drum core construction
b. Magnetically shielded
c. Enameled copper wire: H class
d. Product weight: 0.15g (ref.)
e. Moisture sensitivity Level 1
f. Products comply with RoHS’ requirements
g. Halogen Free available

II. General specification:

a. Storage temp: -40�C to +125�C
b. Operating temp: -40�C to +125�C
(Temp. rise included)
c. Resistance to solder heat: 250�C 10 secs.

For More Information:

Americas - prodinfonetworkamericas@[Link] | Europe - comms-Apps-Europe@[Link] | Asia - prodinfonetworkapac@[Link]

Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be
trademarks or registered trademarks of their respective owners. © Copyright, 2020. Pulse Electronics, Inc. All rights reserved.

5 [Link] W717.I (06/20)

NETWORK PRODUCTS