PRESSURE REDUCING VALVE RP13/E
PED 2014/68/UE 07 2016
TYPE RP13 DN 15-50
Cast Iron EN-GJL-250 PN16
Carbon Steel 1.0619 PN40
Face to face EN 558-1
DESCRIPTION
Series RP13 pressure reducing valve is a self-actuated proportional
action type.
Composed by a direct action single seat special body valve, flow tries
to close, with diaphragm and feedback spring, controlled by
downstream pressure.
The Internal balance without bellow guarantees a long life to the valve.
The series RP13 pressure reducing valve can be simply and easly
installed and it is suitable for industrial plants where compressed air is
not availble for a “pneumatic reducing system” or where the user
requires a stable reduced pressure not subjected to frequent
variations.
SIZES : CONNECTIONS :
from DN 15 to DN 50 BODY : flanged EN1092-1 – PN16 and PN 40 form B
ACTUATOR : female screwed Rp ISO 7 (BSP) Rp 3/8”
MAX WORKING CONDITIONS : REDUCED PRESSURE RANGES :
Maximum inlet pressure with steam or air 23 bar TYPE ACTUATOR RANGE bar
Maximum inlet pressure with water 8 bar C1 T.60 3-8
Maximum design temperature 220 °C C2 T.80 1-5
Maximum downstream reduced pressure (1) 8 bar C3 T.100 0.5 - 3
Minimum downstream reduced pressure 0,2 bar C5 T.150 0.2 - 1.5
(1) C1 special T50 8 – 12 bar
Where control spring ranges overlap, always use the lower range to
give better control and precision
ON REQUEST : ACCESSORIES :
• PTFE/GR Soft seal ≤190°C for class VI° • KIT for STEAM in carton box (weight 2,2 Kg)
• PTFE Soft seal ≤150°C for class VI° pot ( 2,3 lt.), cap, fittings and spring adj. tool
• Stellited seat - plug degree 6 (recommended with Δp ≥ 12 bar) • KIT for WATER and GASES in
• Reduced bore (see table) plastic bag (weight 0,2 Kg)
fitting and spring adjusting tool
CV = american unit (flowrate in USGPM Kv = metric unit (flowrate in m3/h with
with 1 psi of differential pressure) 1 bar of differential pressure)
PLUGS NOMINAL DIAMETER
PT cl. IV° DN 15 DN 20 DN 25 DN 32 DN 40 DN 50
Full bore Ø 1/2” Ø 3/4” Ø 1” Ø 1.1/4” Ø 1.1/2” Ø 2”
CV 2,42 6,12 9,79 17,45 23,89 26,99
KV 2,06 5,22 8,35 14,88 20,38 23,02
Rangeability 6:1 8:1 11:1 14:1 16:1 16:1
Red. bore Ø 1/4” Ø 1/2” Ø 3/4” Ø 1” Ø 1.1/4” Ø 1.1/2”
CV 1,13 2,42 6,12 9,79 17,45 23,89
KV 0,96 2,06 5,22 8,35 14,88 20,38
Rangeability 5:1 6:1 8:1 11:1 14:1 16:1
NOTE : The downstream pipe diameter must be sized according to the specific volume of steam reduced pressure, to obtain a steam velocity
not exceeding 30-35 m/s (maximum limit value = 40 m/s).
Via Lecco, 69/71
20864 AGRATE BRIANZA (MB)
Tel. 039/651.705 - 650.397
Fax 039/654.018
www.conflow.it
COMPONENTS LIST and MATERIALS
COMPONENTS LIST MATERIALS
1. Upper diaphragm casing 1. EN-GJL-250 cast iron
2. Airvent screw 2. 4.8 DIN 933 galvanized steel
3. Hexagonal locknut 3. AISI 304 st. steel
4. Washer 4. DIN 125 galvanized steel
5. Diaphragm casing bolts 5. 8.8 DIN 933 galvanized steel
6. Diaphragm casing locknuts 6. ISO 4033 galvanized steel
7. Diaphragm 7. RubbertexT60-80 (on req.
spec. material for mineral oil)
8. Diaphragm plate NBR T100-150
9. Lower diaphragm casing 8. EN-GJL-250 cast iron
10. Lower spring plate 9. EN-GJL-250 cast iron
11. Grub screw 10. Uni 7013-72 bronze
12. Airtight guide 11. 14.9 DIN 914 steel
13. O-Rings (DN25-DN50) 12. OT58 brass
14. Airtight 13. NBR
15. Spring 14. NBR DIN 3760
15. C85 8 steel (DN15-50)
16. Yoke 16. C40 nickel plated steel
17. Stem 17. AISI 304 st. steel
18. Upper spring plate 18. Free-cutting leaded steel
galvanized
19. Ball bearing (DN40-50) 19. Ref. 51112 steel (DN40-50)
20. Spring adjusting plate 20. Free-cutting leaded steel
galvanized
21. Body locknuts 21. ISO 4033 galvanized steel
22. Stud-bolts 22. Galvanized steel
23. Guide bushing 23. OT58 brass
24. Body gasket 24. Centellen WS 3820
PTFE on request
25. Plug locknut 25. AISI 303 st. steel
26. Entering catch 26. AISI 303 st. steel
27. Plug 27. AISI 304 st. steel
28. Body 28. EN-GJL-250 cast iron or
1.0619 carbon steel
29. Seat 29. AISI 304 st. steel
30. Washer (DN15-20) 30. OT58 brass
31. Seeger (DN15-20) 31. DIN 471 steel
STEM PACKING
DN 15 - 20
SPARE PARTS KIT
Diaphragm ( part. 7 ) Gaskets kit [ parts. 12 - 14 ( n°2 ) – 24 - 30 – 31 ] Gaskets kit [ parts. 13 ( n° 2 ) – 14 – 24 ]
T.50 cod. JMRP13T050RSTD DN 15/20 cod. JRP13TG015020FB-0 DN 25-32 cod. JRP13TG025032FB-0
T.60 cod. JMRP13T060RSTD DN 40-50 cod. JRP13TG040050FB-0
T.80 cod. JMRP13T080RSTD
T.100 cod. JMRP13T100RSTD
T.150 cod. JMRP13T150RSTD
DIMENSIONS (mm) and WEIGHT (Kg)
BODY GROUP ACTUATOR
DN Ø A B C WEIGHT ACTUATOR ØD E WEIGHT
15 1/2” 130 47,5 340 5,5 T.60 149 94 3,5
20 3/4" 150 52,5 333 6,5 T.80 162 93 5,0
25 1” 160 57,5 424 10,5 T.100 188 96 6,5
32 1.1/4” 180 70 427 11,5 T.150 226 93 10,0
40 1.1/2” 200 75 476 17,5
50 2” 230 82,5 482 20,0
For valve sizing, see leaflet n° 100/VP.
Specifications given are only indicative and not binding for the manifacturer who reserve the right to carry-out any
modifications deemed necessary without prior notice. All data sheets by CONFLOW SpA, are available last update on
our internet web site www.conflow.it.
