KJWORKS
KJ-M4 V2
MANUAL
EYE PROTECTION DEVICE MUST BE EQUIPPED DO NOT LOAD ANYTHING BUT BB BULLETS.
DO NOT LOOK THROUGH THE BARREL PLEASE SHOOT IN SAFE PLACE
BEFORE USAGE, THE INSTRUCTION
WARNING: MUSE BE READ.
THANK YOU FOR PURCHASING. THE FOLLOWING ATTENTION POINTS AND INSTRUCTIONS MUST
BE READ. SHOOTING WITHOUT CAUTION OR USED IMPROPERLY, BLINDNESS OR INJURIES COULD
BE LEAD.
DO NOT POINT AT PEOPLE OR ANIMAL. GUN AND GAS MUST NOT BE PLACED IN
AREA WHERE TEMPERATURE IS OVER 40 ℃
PLACE IN GUN CASE WHEN NOT IN USING OR DO NOT USE GAS WHICH PRESSURE IS OVER
TRANSPORTING 12 Kgs/c㎡
UNAUTHORIZED RECONSTRUCTION OF AIR
SOFT GUN TO STRENGTHEN FIRING FUNC- BE CAREFULL WHAT TARGET YOU SHOOT
TION IS STRICTLY PROHIBITED.
[Link] SURE THERE IS NO GAP BETWEEN BOLT
AND CHAMBER [Link] FIRE CONTROL SLECTOR
8. PUSHING FORWARD ASSIST IF THERE IS A GAP
ATTENTION:ONLY SWITCH WHEN HAMMER IS
COCKED
FOLLOW THE DIRECTION
OPERATION
[Link] MAGAZINE CATCH BUTTON AND PULL
[Link] MAGAZINE
DOWN THE MAGAZINE
[Link] CHARGING HANDLE
[Link] BB LOADER TO LOAD BB BULLET.
2
1
[Link] GAS [Link] CHARGING HANDLE
DEPRESS GUARD PLUNGER AND OPEN THE ROTATING ANTICLOCKWISE WHEN IMPACT POINT
TRIGGER GUARD WHEN WEARING ARCTIC MITTENS IS IN RIGHT
[Link] REAR SIGHT
PLACE FRONT SIGHT IN THE CENTER OF REAR
SIGHT
ROTATING CLOCKWISE WHEN IMPACT POINT
IS IN LEFT
ROTATING WINDAGE KNOB AND ELEVATION KNOB
TO ADJUST REAR SIGHT
FULL AUTO
SWITCH BLANK MODE LEVER TO DECIDE THE BOLT
WILL BE CAUGHT OR NOT WHEN RUN OUT OF
BULLET
BLANK
MODE ON
SEMIAUTO
BLANK
MODE OFF
[Link] THE TRIGGER [Link] THE MAGAZINE
[Link] STOP
BOLT WILL BE CAUGHT IN BACK POSITION WHEN [Link] STOCK
RUN OUT OF BULLETS
PRESS ADJUST LEVER TO ADJUST STOCK
1
DISASSEMBLE [Link] FIRE SLECTOR TO SAFE POSITION
[Link] MAGAZINE CATCH BUTTON AND PULL
DOWN THE MAGAZINE
2
[Link] TAKE DOWN PIN
[Link] CHARGING HANDLE
1
[Link] UPPER RECEIVER
[Link] THE CHAMBER TO MAKE SURE THERE IS
NO BULLET IS LOAD
[Link] ADJUSTMENT
ROTATING HOP DIAL TO ADJUST TREJECTORY
RAISING FRONT SIGHT WHEN IMPACT POINT IS HIGHT
L R
ADJUST ACCORDIND TO TREJECTORY
LOWERING FRONT SIGHT WHEN IMPACT POINT IS ROTATING TO R
LOW
STAY
ROTATING TO L
MAGAZINE EXPLODED DRAWING
[Link] CHARGING HANDLE AND BOLT ASSEMBLY
[Link] BACK BUFFER AND SPRING
[Link] BUFFER RETAINER
[Link] CHARGING HANDLE AND BOLT BACK
[Link] UPPER RECEIVER AND PUSH BACK
[Link] BUFFER AND SPRING TAKEDOWN PIN
2
M4 V2 EXPLODED DRAWING
9
NO. NAME OF PART PRICE NO. NAME OF PART PRICE
94 HOP DIAL SPECER 60 H13 ELEVATION KNOB DETENT 40
95 TAKE DOWN PIN DETENT SCREW 20 H14 ELEVATION KNOB DETENT SPRING 20
96 TRIGGER GUARD WINDAGE DRUM SCREW 30 H16 REAR SIGHT BASE PIN 20
97 RECEIVER EXTENSION SCREW 20 H17 HANDLE SCREW 80
110 PISTON1 300 H18 HANDLE RAIL 200
111 CYLINDER PIN 60 H19 HANDLE NUT 100
112 PISTON SPRING 60 H20 ELEVATION KNOB PIN 20
113 PISTON2 80 H21 REAR SIGHT BASE SPRING 20
114 PISTON PIN 20 S1 STOCK 600
115 PISTON SPRING FIXER 80 S2 STOCK LOCKING PIN 100
116 BOLT 600 S3 STOCK LOCKING PIN SPRING 30
117 PISTON FIXER 80 S4 RELEASE LEVER 150
118 BOLT PIN 20 S5 STOCK LOCKING NUT 100
B1 COMPENSATOR 480 S6 STOCK LOCKING NUT SCREW 20
B2 COMPENSATOR SLEEVE 180 S7 STOCK SWIVEL 200
B3 COMPENSATOR WASHER 80 S8 STOCK SWIVEL SCREW 60
B4 OUTTER BARREL SLEEVE 480 M1 MAGAZINE UPPER COVER 120
B6 OUTTER BARREL 960 M2 BLANK MODE LEVER 80
B7 HANDGUARD 240 M3 MAGAZINE UPPER BODY 500
B8 FRONT SIGHT ASSEMBLY BASE 400 M4 MAGAZINE JOINT BODY 400
B9 HELICAL SPRING 20 M5 MAGAZINE UNDER BODY 500
B10 FRONT SIGHT DETENT 50 M6 BB FOLLOWER LINK 120
B11 FRONT SIGHT 80 M7 FOLLOWER 80
B12 FRONT SIGHT ASSEMBLY BASE SCREW 20 M8 VALVE SLEEVE 80
B13 TUBULAR RIVET 30 M9 BB GUIDE 240
B14 HANDGUARD SLIP RING 300 M10 EX VALVE 180
B15 HANDGUARD SLIP RING SPRING 180 M11 CHARGING VALVE 200
B16 BARREL NUT 380 M12 MAGAZINE UPPER COVER PIN 20
B17 RETAINING RING 80 M13 MAGAZINE JOINT SCREW 60
B18 GAS TUBE 120 M14 FOLLOWER SPRING 80
B19 HANDGUARD 200 M15 MAGAZINE GASKET 120
B22 FRONT SWIEVL 200 M16 MAGAZINE JOINT GASKET O-RING 1 30
B23 FRONT SWIVEL PIN 20 M17 MAGAZINE JOINT GASKET O-RING 2 30
H1 HANDLE 1200 M18 JOINT SCREW GASKET 20
H2 REAR SIGHT BASE 280 M19 MAGAZINE TUBE 80
H3 REAR SIGHT 160 T1 BARREL NUT WRENCH 300
H4 WINDAGE KNOB 180 T2 FRONT SIGHT ADJUSTMENT TOOL 80
H5 WINDAGE KNOB DETENT SPRING 20 T3 LOADER 120
H6 WINDAGE KNOB DETENT 40 T4 LOADER TUBE 20
H7 WINDAGE KNOB SCREW 30 T5 LOADER FUNNEL 30
H8 FLAT SPRING 80 T6 LOADER STICK 60
H9 WINDAGE KNOB ADJUST SCREW 100
H10 REAR SIGHT BASE PART 60
H11 ELEVATION INDEX 160
H12 ELEVATION KNOB 200
NO. NAME OF PART PRICE NO. NAME OF PART PRICE
1 UPPER RECEIVER 2400 47B KNOCKER PART B 40
2 FEEDING LAMP 250 48 TRIGGER GUARD 180
3 CHAMBER COVER(L) 180 49 BUFFER RETAINER 180
4 CHAMBER COVER(R) 180 50 RECEIVER EXTENSION 800
5 HOP BASE 120 51 RECEIVER END PLATE 210
6 HOP PLATE 120 52 RECEIVER EXTENSION CAP 240
9 PISTON RING 80 52A RECEIVER EXTENSION CAP O-RING 30
10 CHARGING HANDLE 400 53 BUFFER 360
11 BOLT GUIDE 160 54 BOLT CATCH 300
12 FORWARD ASSIST 180 55 GRIP 600
13 FORWARD ASSIST PLATE 60 56 VALVE LOCK PLATE 240
14A DUSTBIN COVER BROCK A 60 57 AUTO SEAR 240
14B DUSTBIN COVER BROCK B 60 58 RECEIVER PIVOT PIN 200
14C SPRING PIN 20 59 TAKE DOWN PIN 200
14D SPRING 20 60 TRIGGER GUARD PIVOT PIN 30
16 HOP DIAL 60 62 SEAR PIN 30
17 FLOATING VALVE 60 63 SEAR PIN SLEEVE 50
17A FLOATING VALVE O-RING 20 64 BOLT CATCH PIN 30
18 EJECTION PORT COVER 240 65 HAMMER PIN 30
19 CHARGING HANDLE LATCH 100 66 TRIGGER GUARD PLUNGER 30
20 RUBBER CHAMBER 180 67 TAKE DOWN PIN DETENT 20
21 INNER BARREL 420 68 BUFFER TUBE 400
22 CHAMBER RING 100 69A TRIGGER PIN 30
25 DUSTBIN COVER PIN 60 69B TRIGGER PIN TUBE 30
25A DUSTBIN COVER PIN E-RING 20 70 HAMMER SPRING 60
27 FORWARD ASSIST PIN 30 71 TRIGGER SPRING 30
28 FORWARD ASSIST PLATE PIN 30 72 AUTO SEAR SPRING 60
29 DUSTBIN COVER STOP PIN 30 73 VALVE KNOCKER SPRING 60
30 CHARGING HANDLE LATCH PIN 30 74 RECOIL SPRING 200
31 HOP PLATE SPRING 30 75 MAGAZINE RELEASE SPRING 60
34 EJECTION PORT COVER SPRING 30 76 VALVE LOCK PLATE SPRING 30
35 FLOATING VALVE SPRING 30 77 TAKE DOWN PIN DETENT SPRING 20
36 CHARGING HANDLE LATCH SPRING 30 78 BUFFER RETAINER SPRING 20
37 LOWER RECEIVER 2800 79 FIRE SLECTOR SPRING 20
38 VALVE KNOCKER BASE(L) 180 80 TRIGGER GUARD SPRING 20
39 VALVE KNOCKER BASE(R) 180 81 DISCONNECTOR SPRING 20
40 HAMMER 200 82 FORWARD ASSIST SPRING 30
41 TRIGGER 220 83 FORWARD ASSIST PLATE SPRING 20
42 DISCONNECTOR 180 84 BOLT CATCH SPRING 20
43 FIRE CONTROL SLECTOR 240 85 HOP DIAL SCREW 80
44 FIRE CONTROL SLECTOR DETENT 30 85A HOP DIAL SCREW O-RING 20
45 MAGAZINE CATCH 240 86 FEEDING LAMP SCREW 20
46 MAGAZINE CATCH BUTTON 180 87 BUFFER RETAINER SCREW 20
47 KNOCKER 160 92 GRIP SCREW 30
47A KNOCKER PART A 40 93 GRIP SCREW WASHER 20
KJWORKS
Kjworks No.12 Lian-Ming 1st Street,Bade City,Taoyuan county,Taiwan
Tel:03-3749793 Fax:03-3618130 e-mail:kjworks@[Link] Website:[Link]
