Film Capacitors

Metallized Polypropylene Film Capacitors (MKP)

Series/Type: B32671L, B32672L

Date: August 2019

© TDK Electronics AG 2020. Reproduction, publication and dissemination of this publication, enclosures hereto
and the information contained therein without TDK Electronics' prior express consent is prohibited.
Metallized polypropylene film capacitors (MKP) B32671L, B32672L
High V AC, high temperature (wound)

Typical applications Dimensional drawing

Electronic ballasts (resonant circuits)
SMPS
High-frequency AC loads
Pulse circuits

Climatic
Max. operating temperature: 125 °C
Climatic category (IEC 60068-1:2013):
55/110/56

Construction
Dimensions in mm
Dielectric: metallized polypropylene (PP)
Wound capacitor technology
Lead spacing Lead diameter Type
Plastic case (UL 94 V-0)
±0.4 d1 ±0.05
Epoxy resin sealing
10 0.6 B32671L
Features 15 0.8 B32672L
Very high AC voltages for all frequency
ranges
Very small dimensions
High peak voltage for short time periods
High peak current
High pulse withstand capability
RoHS-compatible
Halogen-free capacitors available on request
AEC-Q200D compliant

Terminals
Parallel wire leads, lead-free tinned
Special lead lengths available on request

Marking
Manufacturer's logo
lot number, series number
Rated capacitance (coded)
Capacitance tolerance (code letter)
Rated voltage
Date of manufacture (coded)

Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For notes on taping, refer to chapter "Taping and packing“.

Please read Cautions and warnings and Page 2 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Overview of available types

Lead spacing 10 mm 15 mm
Type B32671L B32672L
Page 4 6
VRMS (V AC) 200 250 250 500 600 700 160 200 250 250 500 600 700 900
VR (V DC) 400 630 1000 1000 1600 2000 250 450 630 1000 1300 1600 2000 2000
CR (nF)
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
150
220
330
390
470
680
1000

Please read Cautions and warnings and Page 3 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Ordering codes and packing units (lead spacing 10 mm)

VRMS VR CR Max. dimensions Ordering code Ammo Reel Untaped

f ≤1 kHz w×h×l (composition see pack
V AC V DC nF mm below) pcs./MOQ pcs./MOQ pcs./MOQ
200 400 22 4.0 × 9.0 × 13.0 B32671L4223+*** 4000 6800 4000
33 4.0 × 9.0 × 13.0 B32671L4333+*** 4000 6800 4000
47 5.0 × 11.0 × 13.0 B32671L4473+*** 3320 5200 4000
68 5.0 × 11.0 × 13.0 B32671L4683+*** 3320 5200 4000
100 6.0 × 12.0 × 13.0 B32671L4104+*** 2720 4400 4000
250 630 15 4.0 × 9.0 × 13.0 B32671L6153+*** 4000 6800 4000
22 5.0 × 11.0 × 13.0 B32671L6223+*** 3320 5200 4000
33 5.0 × 11.0 × 13.0 B32671L6333+*** 3320 5200 4000
47 6.0 × 12.0 × 13.0 B32671L6473+*** 2720 4400 4000
56 6.0 × 12.0 × 13.0 B32671L6563+*** 2720 4400 4000
250 1000 4.7 4.0 × 9.0 × 13.0 B32671L9472+*** 4000 6800 4000
6.8 4.0 × 9.0 × 13.0 B32671L9682+*** 4000 6800 4000
10 5.0 × 11.0 × 13.0 B32671L9103+*** 3320 5200 4000
15 5.0 × 11.0 × 13.0 B32671L9153+*** 3320 5200 4000
22 6.0 × 12.0 × 13.0 B32671L9223+*** 2720 4400 4000
500 1000 3.3 4.0 × 9.0 × 13.0 B32671L0332+*** 4000 6800 4000
3.9 4.0 × 9.0 × 13.0 B32671L0392+*** 4000 6800 4000
4.7 4.0 × 9.0 × 13.0 B32671L0472+*** 4000 6800 4000
5.6 5.0 × 11.0 × 13.0 B32671L0562+*** 3320 5200 4000
6.2 5.0 × 11.0 × 13.0 B32671L0622+*** 3320 5200 4000
6.8 5.0 × 11.0 × 13.0 B32671L0682+*** 3320 5200 4000
8.2 6.0 × 12.0 × 13.0 B32671L0822+*** 2720 4400 4000
10 6.0 × 12.0 × 13.0 B32671L0103+*** 2720 4400 4000
12 6.0 × 12.0 × 13.0 B32671L0123+*** 2720 4400 4000

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
K = ±10% 289 = Straight terminals, Ammo pack
J = ±5% 189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)

Please read Cautions and warnings and Page 4 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Ordering codes and packing units (lead spacing 10 mm)

VRMS VR CR Max. dimensions Ordering code Ammo Reel Untaped

f ≤1 kHz w×h×l (composition see pack
V AC V DC nF mm below) pcs./MOQ pcs./MOQ pcs./MOQ
600 1600 1.2 4.0 × 9.0 × 13.0 B32671L1122+*** 4000 6800 4000
1.5 4.0 × 9.0 × 13.0 B32671L1152+*** 4000 6800 4000
2.2 5.0 × 11.0 × 13.0 B32671L1222+*** 3320 5200 4000
2.7 5.0 × 11.0 × 13.0 B32671L1272+*** 3320 5200 4000
3.3 6.0 × 12.0 × 13.0 B32671L1332+*** 2720 4400 4000
3.9 6.0 × 12.0 × 13.0 B32671L1392+*** 2720 4400 4000
4.7 6.0 × 12.0 × 13.0 B32671L1472+*** 2720 4400 4000
700 2000 1.0 4.0 × 9.0 × 13.0 B32671L8102+*** 4000 6800 4000
1.2 4.0 × 9.0 × 13.0 B32671L8122+*** 4000 6800 4000
1.5 4.0 × 9.0 × 13.0 B32671L8152+*** 4000 6800 4000
2.2 5.0 × 11.0 × 13.0 B32671L8222+*** 3320 5200 4000
2.7 5.0 × 11.0 × 13.0 B32671L8272+*** 3320 5200 4000
3.3 5.0 × 11.0 × 13.0 B32671L8332+*** 3320 5200 4000
3.9 6.0 × 12.0 × 13.0 B32671L8392+*** 2720 4400 4000
4.7 6.0 × 12.0 × 13.0 B32671L8472+*** 2720 4400 4000

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
K = ±10% 289 = Straight terminals, Ammo pack
J = ±5% 189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)

Please read Cautions and warnings and Page 5 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Ordering codes and packing units (lead spacing 15 mm)

VRMS VR CR Max. dimensions Ordering code Ammo Reel Untaped

f ≤1 kHz w×h×l (composition see pack
V AC V DC nF mm below) pcs./MOQ pcs./MOQ pcs./MOQ
160 250 150 5.0 × 10.5 × 18.0 B32672L2154+*** 4680 5200 4000
220 6.0 × 11.0 × 18.0 B32672L2224+*** 3840 4400 4000
330 7.0 × 12.5 × 18.0 B32672L2334+*** 3320 3600 4000
470 8.5 × 14.5 × 18.0 B32672L2474+*** 2720 2800 2000
680 9.0 × 17.5 × 18.0 B32672L2684+*** 2560 2800 2000
1000 11.0 × 18.5 × 18.0 B32672L2105+***  2200 1200
200 450 68 5.0 × 10.5 × 18.0 B32672L4683+*** 4680 5200 4000
100 5.0 × 10.5 × 18.0 B32672L4104+*** 4680 5200 4000
150 6.0 × 11.0 × 18.0 B32672L4154+*** 3840 4400 4000
220 7.0 × 12.5 × 18.0 B32672L4224+*** 3320 3600 4000
330 8.0 × 14.0 × 18.0 B32672L4334+*** 2920 3000 2000
470 9.0 × 17.5 × 18.0 B32672L4474+*** 2560 2800 2000
680 11.0 × 18.5 × 18.0 B32672L4684+***  2200 1200
250 630 33 5.0 × 10.5 × 18.0 B32672L6333+*** 4680 5200 4000
47 5.0 × 10.5 × 18.0 B32672L6473+*** 4680 5200 4000
68 6.0 × 11.0 × 18.0 B32672L6683+*** 3840 4400 4000
100 7.0 × 12.5 × 18.0 B32672L6104+*** 3320 3600 4000
150 8.5 × 14.5 × 18.0 B32672L6154+*** 2720 2800 2000
220 9.0 × 17.5 × 18.0 B32672L6224+*** 2560 2800 2000
390 11.0 × 18.5 × 18.0 B32672L6394+***  2200 1200

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
K = ±10% 289 = Straight terminals, Ammo pack
J = ±5% 189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)

Please read Cautions and warnings and Page 6 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Ordering codes and packing units (lead spacing 15 mm)

VRMS VR CR Max. dimensions Ordering code Ammo Reel Untaped

f ≤1 kHz w×h×l (composition see pack
V AC V DC nF mm below) pcs./MOQ pcs./MOQ pcs./MOQ
250 1000 10 5.0 × 10.5 × 18.0 B32672L0103+*** 4680 5200 4000
15 5.0 × 10.5 × 18.0 B32672L0153+*** 4680 5200 4000
22 5.0 × 10.5 × 18.0 B32672L0223+*** 4680 5200 4000
33 6.0 × 11.0 × 18.0 B32672L0333+*** 3840 4400 4000
47 7.0 × 12.5 × 18.0 B32672L0473+*** 3320 3600 4000
68 8.5 × 14.5 × 18.0 B32672L0683+*** 2720 2800 2000
100 9.0 × 17.5 × 18.0 B32672L0104+*** 2560 2800 2000
150 11.0 × 18.5 × 18.0 B32672L0154+***  2200 1200
500 1300 6.8 5.0 × 10.5 × 18.0 B32672L7682+*** 4680 5200 4000
10 5.0 × 10.5 × 18.0 B32672L7103+*** 4680 5200 4000
22 7.0 × 12.5 × 18.0 B32672L7223+*** 3320 3600 4000
33 8.5 × 14.5 × 18.0 B32672L7333+*** 2720 2800 2000
47 9.0 × 17.5 × 18.0 B32672L7473+*** 2560 2800 2000
68 11.0 × 18.5 × 18.0 B32672L7683+***  2200 1200
600 1600 6.2 5.0 × 10.5 × 18.0 B32672L1622+*** 4680 5200 4000
6.8 5.0 × 10.5 × 18.0 B32672L1682+*** 4680 5200 4000
8.2 6.0 × 11.0 × 18.0 B32672L1822+*** 3840 4400 4000
10 6.0 × 11.0 × 18.0 B32672L1103+*** 3840 4400 4000
12 6.0 × 12.0 × 18.0 B32672L1123+*** 3840 4400 4000
15 7.0 × 12.5 × 18.0 B32672L1153+*** 3320 3600 4000
22 8.5 × 14.5 × 18.0 B32672L1223+*** 2720 2800 2000
33 9.0 × 17.5 × 18.0 B32672L1333+*** 2560 2800 2000
47 11.0 × 18.5 × 18.0 B32672L1473+***  2200 1200

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
K = ±10% 289 = Straight terminals, Ammo pack
J = ±5% 189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)

Please read Cautions and warnings and Page 7 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Ordering codes and packing units (lead spacing 15 mm)

VRMS VR CR Max. dimensions Ordering code Ammo Reel Untaped

f ≤1 kHz w×h×l (composition see pack
V AC V DC nF mm below) pcs./MOQ pcs./MOQ pcs./MOQ
700 2000 1.0 5.0 × 10.5 × 18.0 B32672L8102+*** 4680 5200 4000
1.2 5.0 × 10.5 × 18.0 B32672L8122+*** 4680 5200 4000
1.5 5.0 × 10.5 × 18.0 B32672L8152+*** 4680 5200 4000
2.2 5.0 × 10.5 × 18.0 B32672L8222+*** 4680 5200 4000
2.7 5.0 × 10.5 × 18.0 B32672L8272+*** 4680 5200 4000
3.3 5.0 × 10.5 × 18.0 B32672L8332+*** 4680 5200 4000
3.9 5.0 × 10.5 × 18.0 B32672L8392+*** 4680 5200 4000
4.7 5.0 × 10.5 × 18.0 B32672L8472+*** 4680 5200 4000
5.6 6.0 × 11.0 × 18.0 B32672L8562+*** 3840 4400 4000
6.2 6.0 × 11.0 × 18.0 B32672L8622+*** 3840 4400 4000
6.8 6.0 × 11.0 × 18.0 B32672L8682+*** 3840 4400 4000
8.2 6.0 × 12.0 × 18.0 B32672L8822+*** 3840 4400 4000
10 7.0 × 12.5 × 18.0 B32672L8103+*** 3320 3600 4000
12 8.5 × 14.5 × 18.0 B32672L8123+*** 2720 2800 2000
15 8.5 × 14.5 × 18.0 B32672L8153+*** 2720 2800 2000
22 9.0 × 17.5 × 18.0 B32672L8223+*** 2560 2800 2000
33 11.0 × 18.5 × 18.0 B32672L8333+***  2200 1200

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
K = ±10% 289 = Straight terminals, Ammo pack
J = ±5% 189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)

Please read Cautions and warnings and Page 8 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Ordering codes and packing units (lead spacing 15 mm)

VRMS VR CR Max. dimensions Ordering code Ammo Reel Untaped

f ≤1 kHz w×h×l (composition see pack
V AC V DC nF mm below) pcs./MOQ pcs./MOQ pcs./MOQ
900 2000 1.0 5.0 × 10.5 × 18.0 B32672L9102+*** 4680 5200 4000
1.2 6.0 × 11.0 × 18.0 B32672L9122+*** 3840 4400 4000
1.5 6.0 × 11.0 × 18.0 B32672L9152+*** 3840 4400 4000
2.2 7.0 × 12.5 × 18.0 B32672L9222+*** 3320 3600 4000
2.7 8.0 × 14.0 × 18.0 B32672L9272+*** 2920 3000 2000
3.3 8.5 × 14.5 × 18.0 B32672L9332+*** 2720 2800 2000
3.9 9.0 × 17.5 × 18.0 B32672L9392+*** 2560 2800 2000
4.7 9.0 × 17.5 × 18.0 B32672L9472+*** 2560 2800 2000
5.6 11.0 × 18.5 × 18.0 B32672L9562+***  2200 1200
6.2 11.0 × 18.5 × 18.0 B32672L9622+***  2200 1200
6.8 11.0 × 18.5 × 18.0 B32672L9682K***  2200 1200

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
K = ±10% 289 = Straight terminals, Ammo pack
J = ±5% 189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)

Please read Cautions and warnings and Page 9 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Technical data

Reference standard: IEC 60384-16:2005 and AEC-Q200D. All data given at T = 20 °C, unless
otherwise specified.
Rated temperature TR +85 °C
Operating temperature Max. operating temperature Top,max +125 °C
range Upper category temperature Tmax +110 °C
Lower category temperature Tmin 55 °C
Rated temperature TR +85 °C
Dissipation factor tan δ at ≤27 nF 27 nF< CR ≤0.1 μF 0.1 μF < CR ≤1 μF >1 μF
(in 10-3) at 20 °C 1 kHz 0.8 0.8 0.8 0.8
(upper limit values) 10 kHz 1.0 1.0 1.0 
100 kHz 2.0 3.0  
Insulation resistance Rins 100 GΩ (CR ≤ 0.33 μF)
or time constant 30000 s (CR > 0.33 μF)
τ = CR  Rins at 20 °C,
rel. humidity ≤ 65%
(minimum as-delivered
values)
DC test voltage 1.6  VR, 2 s
Category voltage VC Top (°C) DC voltage derating AC voltage derating
(continuous operation Top ≤ 85 VC = VR VC,RMS = VRMS
with VDC or VAC at f ≤1 kHz) 85<Top≤110 VC = VR  (165Top)/80 VC,RMS=VRMS  (165Top)/80
Operating voltage Vop for Top (°C) DC voltage (max. hours) AC voltage (max. hours)
short operating periods Top ≤ 100 Vop = 1.25  VC (2000 h) Vop = 1.0  VC,RMS (2000 h)
(VDC or VAC at f ≤1 kHz) 100<Top≤125 Vop = 1.25  VC (1000 h) Vop = 1.0  VC,RMS (1000 h)
Biased humidity 1000 h / 40 °C / 93% relative humidity with VR,DC
Limit values after test Capacitance change ΔC/C ≤ 5%
Dissipation factor change Δ tan δ ≤ 0.002 (at 1 kHz)
Insulation resistance Rins ≥ 200 MΩ
Reliability:
Failure rate λ 1 fit (≤ 1  10-9/h) at 0.5  VR, 40 °C
Service life tSL 200 000 h at 1.0  VR, 85 °C
For conversion to other operating conditions and temperatures, refer
to chapter "Quality, 2 Reliability".
Failure criteria:
Total failure Short circuit or open circuit
Failure due to variation Capacitance change ΔC/C > 10%
of parameters Dissipation factor tan δ > 4  upper limit values
Insulation resistance Rins < 1500 MΩ

Please read Cautions and warnings and Page 10 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Pulse handling capability

"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/μs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V2/μs.

Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor. These parameters are given for isolated pulses in such a way that the heat generated
by one pulse will be completely dissipated before applying the next pulse. For a train of pulses,
please refer to the curves of permissible AC voltage-current versus frequency.

dV/dt values
Lead spacing 10 mm
Type B32671L
VRMS (V AC) 200 250 500 600 700
VR (V DC) 400 630 1000 1000 1600 2000
CR (nF) dV/dt in V/μs
1.0      11000
1.2     6000 10000
1.5     5600 9500
2.2     5200 9000
2.7     5000 8600
3.3    4700 4700 8500
3.9    4300 4500 8200
4.7   810 3800 4000 8000
5.6    3400  
6.2    3200  
6.8   810 3100  
8.2    2700  
10   810 2500  
12    2300  
15  540 810   
22 400 540 810   
33 400 540    
47 400 540    
56  540    
68 400     
100 400     

Please read Cautions and warnings and Page 11 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

dV/dt values
Lead spacing 15 mm
Type B32672L
VRMS (V AC) 160 200 250 500 600 700 900
VR (V DC) 250 450 630 1000 1300 1600 2000 2000
CR (nF) dV/dt in V/μs
1.0       10000 15000
1.2       9400 14100
1.5       9000 13500
2.2       7500 11000
2.7       7100 10600
3.3       6800 10000
3.9       6000 9000
4.7       5500 8200
5.6       5000 7500
6.2      3600 4700 7000
6.8     1000 3500 4500 6700
8.2      3100 4200 
10    445 1000 2800 3900 
12      2600 3600 
15    445  2300 3300 
22    445 1000 2000 2900 
33   300 445 1000 1700 2300 
47   300 445 1000 1400  
56        
68  200 300 445 1000   
100  200 300 445    
150 170 200 300 445    
220 170 200 300     
330 170 200      
390   300     
470 170 200      
680 170 200      
1000 170       

Please read Cautions and warnings and Page 12 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

k0 values
Lead spacing 10 mm
Type B32671L
VRMS (V AC) 200 250 500 600 700
VR (V DC) 400 630 1000 1000 1600 2000
CR (nF) k0 in V2/μs
1.0      25000000
1.2     14400000 23000000
1.5     14000000 22500000
2.2     13800000 22000000
2.7     13600000 21500000
3.3    9400000 13300000 21000000
3.9    8600000 13100000 20900000
4.7   400000 8200000 12000000 20800000
5.6    7600000 
6.2    6800000 
6.8   400000 6200000 
8.2    5400000 
10   400000 5000000 
12    4600000 
15  200000 400000  
22 150000 200000 400000  
33 150000 200000   
47 150000 200000   
56  200000   
68 150000    
100 150000    

Please read Cautions and warnings and Page 13 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

k0 values
Lead spacing 15 mm
Type B32672L
VRMS (V AC) 160 200 250 500 600 700 900
VR (V DC) 250 450 630 1000 1300 1600 2000 2000
CR (nF) k0 in V2/μs
1.0       20300000 30000000
1.2       19600000 29400000
1.5       19200000 28000000
2.2       18600000 27500000
2.7       18200000 27300000
3.3       18000000 27000000
3.9       16800000 25200000
4.7       15800000 23500000
5.6       13100000 19500000
6.2      11520000 12700000 19000000
6.8     3000000 11200000 12300000 18400000
8.2      9920000 11800000 
10    1000000 3000000 8960000 11100000 
12      8320000 10600000 
15    1000000  7360000 10400000 
22    1000000 3000000 6400000 9300000 
33   500000 1000000 3000000 5440000 9000000 
47   500000 1000000 3000000 4480000  
56        
68  120000 500000 1000000 3000000   
100  120000 500000 1000000    
150 100000 120000 500000 1000000    
220 100000 120000 500000     
330 100000 120000      
390   500000     
470 100000 120000      
680 100000      
1000 100000       

Please read Cautions and warnings and Page 14 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Impedance Z versus frequency f

(typical values)

Please read Cautions and warnings and Page 15 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 10 mm
400 V DC/200 V AC 630 V DC/250 V AC

1000 V DC/250 V AC 1000 V DC/500 V AC

Please read Cautions and warnings and Page 16 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 10 mm
1600 V DC/600 V AC 2000 V DC/700 V AC

Please read Cautions and warnings and Page 17 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 15 mm
250 V DC/160 V AC 450 V DC/200 V AC

630 V DC/250 V AC 1000 V DC/250 V AC

Please read Cautions and warnings and Page 18 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 15 mm
1300 V DC/500 V AC 1600 V DC/600 V AC

2000 V DC/700 V AC 2000 V DC/900 V AC

Please read Cautions and warnings and Page 19 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 10 mm
400 V DC/200 V AC 630 V DC/250 V AC

1000 V DC/250 V AC 1000 V DC/500 V AC

Please read Cautions and warnings and Page 20 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 10 mm
1600 V DC/600 V AC 2000 V DC/700 V AC

Please read Cautions and warnings and Page 21 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 15 mm
250 V DC/160 V AC 450 V DC/200 V AC

630 V DC/250 V AC 1000 V DC/250 V AC

Please read Cautions and warnings and Page 22 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.

Lead spacing 15 mm
1300 V DC/500 V AC 1600 V DC/600 V AC

2000 V DC/700 V AC 2000 V DC/900 V AC

Please read Cautions and warnings and Page 23 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Maximum AC voltage (VRMS), current (IRMS) versus frequency and temperature for TA >100 °C
The graphs described in the previous section for the permissible AC voltage (VRMS) or current
(IRMS) versus frequency are given for a maximum ambient temperature TA ≤100 ºC. In case of
higher ambient temperatures (TA), the self-heating (ΔT) of the component must be reduced to
avoid that temperature of the component (Top= TA + ΔT) reaches values above maximum
operating [Link] factor FT shall be applied in the following way:

And FT is given by the following curve:

Please read Cautions and warnings and Page 24 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Operation at overvoltages during heating and ignition of lamps (TA ≤40 °C)
In lighting applications, the capacitors can be subjected to overvoltages during the heating and ig-
nition periods. An overvoltage occurs when the operating voltage exceeds the permissible
AC voltage at the resonant frequency fr.

For a repetitive application of on/off switching pulses (as for example in the life tests applied by
electronic ballast manufacturers), limits have to be imposed on the time periods under overvolt-
age and on the duty cycle, in order to keep the capacitance value within the required margins:

The overvoltage time tOV should be less than 1 sec.

The K0 calculated in the overvoltage period (see general technical information) shall be lower
than the maximum K0 provided.
The maximum duty cycle of the overvoltage is given by

where VRMS,ov is the RMS voltage during period tOV

and VRMS is the permissible AC voltage for continuous operation at the resonant frequency fr
(given by the “permissible AC voltage versus frequency f” graphics in theprevious pages).

The drift of capacitance depends on the Vpp attained, and the total time under overvoltage,
which is calculated in hours as follows:
(Ni  tOV) / 3600
where Ni is the number of overvoltage impulses and tOV is expressed in seconds.

The maximum drift of capacitance as a function of both parameters is provided graphically in the
following pages.

Please read Cautions and warnings and Page 25 of 39

Important notes at the end of this document.
 B32671L
High V AC, high temperature (wound)

Estimation of the maximum drift of capacitance value in function of the number of total
hours overvoltage

Lead spacing 10 mm
500 V AC/1000 V DC 600 V AC/1600 V DC

Please read Cautions and warnings and Page 26 of 39

Important notes at the end of this document.
 B32672L
High V AC, high temperature (wound)

Estimation of the maximum drift of capacitance value in function of the number of total
hours overvoltage

Lead spacing 15 mm
600 V AC/1600 V DC 700 V AC/2000 V DC

Please read Cautions and warnings and Page 27 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Testing and Standards

Test Reference Conditions of test Performance

requirements
Electrical IEC 60384-16:2005 Voltage proof, 1.6 VR, 1 minute Within specified limits
para- Insulation resistance, Rins
meters Capacitance, C
Dissipation factor, tan δ
Robust- IEC Tensile strength (test Ua1) Capacitance and tan δ
ness of ter- 60068-2-21:2006 Wire diameter Tensile force within specified limits
minations 0.5 < d1 ≤ 0.8 mm 10 N
Resis- IEC Solder bath temperature at 260 ±5 °C, ΔC/C0 ≤ 2%
tance to 60068-2-20:2008, immersion for 10 seconds Δ tan δ ≤ 0.002
soldering test Tb,
heat method 1A
Rapid IEC 60384-16:2005 TA = lower category temperature
change of TB = upper category temperature
tempera- Five cycles, duration t = 30 min.
ture
Vibration IEC 60384-16:2005 Test Fc: vibration sinusoidal No visible damage
Displacement: 0.75 mm
Accleration: 98 m/s2
Frequency: 10 Hz ... 500 Hz
Test duration: 3 orthogonal axes,
2 hours each axe
Bump IEC 60384-16:2005 Test Eb: Total 4000 bumps with No visible damage
390 m/s2 mounted on PCB ΔC/C0 ≤ 2%
Δ tan δ ≤ 0.002
Duration: 6 ms
Rins ≥ 50% of initial limit
Climatic IEC 60384-16:2005 Dry heat Tb / 16 h No visible damage
sequence Damp heat cyclic, 1st cycle ΔC/C0 ≤ 3%
+55 °C / 24 h / 95% ... 100% RH Δ tan δ ≤ 0.001
Cold Ta / 2 h Rins ≥ 50% of initial limit
Damp heat cyclic, 5 cycles
+55 °C / 24 h / 95% ... 100% RH
Damp IEC 60384-16:2005 Test Ca No visible damage
heat, 40 °C / 93% RH / 56 days ΔC/C0 ≤ 3%
steady Δ tan δ ≤ 0.001
state Rins ≥ 50% of initial limit
Advanced 60 °C / 95% RH / 1000 hours with VR,DC No visible damage
biased ΔC/C0 ≤ 10%
humidity Δ tan δ ≤ 0.002
Rins ≥ 50% of initial limit

Please read Cautions and warnings and Page 28 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Test Reference Conditions of test Performance

requirements
Endurance IEC 60384-16:2005 85 °C / 1.25 VR / 2000 hours No visible damage
ΔC/C0 ≤ 5%
Δ tan δ ≤ 0.002
Rins ≥ 50% of initial limit
Endurance IEC 60384-16:2005 110 °C / 1.25 VC / 2000 hours No visible damage
ΔC/C0 ≤ 10%
Δ tan δ ≤ 0.002
Rins ≥ 50% of initial limit

Mounting guidelines

1 Soldering

1.1 Solderability of leads

The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.

Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.

Solder bath temperature 235 ±5 °C

Soldering time 2.0 ±0.5 s
Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane
Evaluation criteria:
Wetting of wire surface by new solder ≥90%,
Visual inspection
free-flowing solder

Please read Cautions and warnings and Page 29 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

1.2 Resistance to soldering heat

Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1.
Conditions:

Series Solder bath temperature Soldering time

MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C 10 ±1 s
coated
uncoated (lead spacing >10 mm)
MFP
MKP (lead spacing >7.5 mm)
MKT boxed (case 2.5 × 6.5 × 7.2 mm) 5 ±1 s
MKP (lead spacing ≤7.5 mm) <4 s
MKT uncoated (lead spacing ≤10 mm) recommended soldering
insulated (B32559) profile for MKT uncoated
(lead spacing ≤ 10 mm) and
insulated (B32559)

Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane

Shield Heat-absorbing board, (1.5 ±0.5) mm thick, between
capacitor body and liquid solder
Evaluation criteria:
Visual inspection No visible damage
2% for MKT/MKP/MFP
ΔC/C0
5% for EMI suppression capacitors
tan δ As specified in sectional specification

Please read Cautions and warnings and Page 30 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

1.3 General notes on soldering

Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature Tmax. Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings

The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.

Recommendations
As a reference, the recommended wave soldering profile for our film capacitors is as follows:

Please read Cautions and warnings and Page 31 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Body temperature should follow the description below:

MKP capacitor
During pre-heating: Tp ≤110 °C
During soldering: Ts ≤120 °C, ts ≤45 s
MKT capacitor
During pre-heating: Tp ≤125 °C
During soldering: Ts ≤160 °C, ts ≤45 s
When SMD components are used together with leaded ones, the film capacitors should not pass
into the SMD adhesive curing oven. The leaded components should be assembled after the SMD
curing step.
Leaded film capacitors are not suitable for reflow soldering.
In order to ensure proper conditions for manual or selective soldering, the body temperature of
the capacitor (Ts) must be ≤120 °C.
One recommended condition for manual soldering is that the tip of the soldering iron should
be <360 °C and the soldering contact time should be no longer than 3 seconds.
For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 °C in the preheater phase
rapid cooling after soldering
Please refer to our Film Capacitors Data Book in case more details are needed.

Please read Cautions and warnings and Page 32 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Cautions and warnings

Do not exceed the upper category temperature (UCT).

Do not apply any mechanical stress to the capacitor terminals.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after it has been soldered to the PC board.
Do not pick up the PC board by the soldered capacitor.
Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified
lead spacing.
Do not exceed the specified time or temperature limits during soldering.
Avoid external energy inputs, such as fire or electricity.
Avoid overload of the capacitors.
Consult us if application is with severe temperature and humidity condition.
There are no serviceable or repairable parts inside the capacitor. Opening the capacitor or
any attempts to open or repair the capacitor will void the warranty and liability of
TDK Electronics.
Please note that the standards referred to in this publication may have been revised in the
meantime.

The table below summarizes the safety instructions that must always be observed. A detailed
description can be found in the relevant sections of the chapters "General technical information"
and "Mounting guidelines".

Topic Safety information Reference chapter

"General technical
information"
Storage Make sure that capacitors are stored within the 4.5
conditions specified range of time, temperature and humidity "Storage conditions"
conditions.
Flammability Avoid external energy, such as fire or electricity 5.3
(passive flammability), avoid overload of the capacitors "Flammability"
(active flammability) and consider the flammability of
materials.
Resistance to Do not exceed the tested ability to withstand vibration. 5.2
vibration The capacitors are tested to IEC 60068-2-6:2007. "Resistance to
TDK Electronics offers film capacitors specially vibration"
designed for operation under more severe vibration
regimes such as those found in automotive
applications. Consult our catalog "Film Capacitors for
Automotive Electronics".

Please read Cautions and warnings and Page 33 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Topic Safety information Reference chapter

"Mounting guidelines"
Soldering Do not exceed the specified time or temperature limits 1 "Soldering"
during soldering.
Cleaning Use only suitable solvents for cleaning capacitors. 2 "Cleaning"
Embedding of When embedding finished circuit assemblies in plastic 3 "Embedding of
capacitors in resins, chemical and thermal influences must be taken capacitors in finished
finished into account. assemblies"
assemblies Caution: Consult us first, if you also wish to embed
other uncoated component types!

Display of ordering codes for TDK Electronics products

The ordering code for one and the same product can be represented differently in data sheets,
data books, other publications, on the company website, or in order-related documents such as
shipping notes, order confirmations and product labels. The varying representations of the order-
ing codes are due to different processes employed and do not affect the specifications of the re-
spective products.
Detailed information can be found on the Internet under
[Link]/orderingcodes.

&RUUHODWLRQRIGDWDVKHHWYDOXHVDQGPRGHOOLQJWRRORXWSXWV
'DWDVKHHWYDOXHVDQGUHVXOWVRIGHVLJQWRROVPD\GHYLDWHDVWKH\KDYHQRWEHHQGHULYHGLQWKH
VDPHFRQWH[W
:KLOH GDWD VKHHWV VKRZ LQGLYLGXDO SDUDPHWHU VWDWHPHQWV ZLWKRXW FRQVLGHULQJ D SRVVLEOH GHSHQ
GHQF\WRRWKHUSDUDPHWHUV7RROVPRGHODFRPSOHWHJLYHQVFHQDULRDVLQSXWDQGSURFHVVHGLQVLGH
WKHWRRO
)XUWKHUPRUHDVZHFRQVWDQWO\VWULYHWRLPSURYHRXUPRGHOVWKHUHVXOWVRIWRROVFDQFKDQJHRYHU
WLPHDQGEHDQRQELQGLQJLQGLFDWLRQRQO\

Please read Cautions and warnings and Page 34 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Symbols and terms

Symbol English German

α Heat transfer coefficient Wärmeübergangszahl
αC Temperature coefficient of capacitance Temperaturkoeffizient der Kapazität
A Capacitor surface area Kondensatoroberfläche
βC Humidity coefficient of capacitance Feuchtekoeffizient der Kapazität
C Capacitance Kapazität
CR Rated capacitance Nennkapazität
ΔC Absolute capacitance change Absolute Kapazitätsänderung
ΔC/C Relative capacitance change (relative Relative Kapazitätsänderung (relative
deviation of actual value) Abweichung vom Ist-Wert)
ΔC/CR Capacitance tolerance (relative deviation Kapazitätstoleranz (relative Abweichung
from rated capacitance) vom Nennwert)
dt Time differential Differentielle Zeit
Δt Time interval Zeitintervall
ΔT Absolute temperature change Absolute Temperaturänderung
(self-heating) (Selbsterwärmung)
Δtan δ Absolute change of dissipation factor Absolute Änderung des Verlustfaktors
ΔV Absolute voltage change Absolute Spannungsänderung
dV/dt Time differential of voltage function (rate
Differentielle Spannungsänderung
of voltage rise) (Spannungsflankensteilheit)
ΔV/Δt Voltage change per time interval Spannungsänderung pro Zeitintervall
E Activation energy for diffusion Aktivierungsenergie zur Diffusion
ESL Self-inductance Eigeninduktivität
ESR Equivalent series resistance Ersatz-Serienwiderstand
f Frequency Frequenz
f1 Frequency limit for reducing permissible Grenzfrequenz für thermisch bedingte
AC voltage due to thermal limits Reduzierung der zulässigen
Wechselspannung
f2 Frequency limit for reducing permissible Grenzfrequenz für strombedingte
AC voltage due to current limit Reduzierung der zulässigen
Wechselspannung
fr Resonant frequency Resonanzfrequenz
FD Thermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur
Diffusion
FT Derating factor Deratingfaktor
i Current (peak) Stromspitze
IC Category current (max. continuous Kategoriestrom (max. Dauerstrom)
current)

Please read Cautions and warnings and Page 35 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Symbol English German

IRMS (Sinusoidal) alternating current, (Sinusförmiger) Wechselstrom
root-mean-square value
iz Capacitance drift Inkonstanz der Kapazität
k0 Pulse characteristic Impulskennwert
LS Series inductance Serieninduktivität
λ Failure rate Ausfallrate
λ0 Constant failure rate during useful Konstante Ausfallrate in der
service life Nutzungsphase
λtest Failure rate, determined by tests Experimentell ermittelte Ausfallrate
Pdiss Dissipated power Abgegebene Verlustleistung
Pgen Generated power Erzeugte Verlustleistung
Q Heat energy Wärmeenergie
ρ Density of water vapor in air Dichte von Wasserdampf in Luft
R Universal molar constant for gases Allg. Molarkonstante für Gas
R Ohmic resistance of discharge circuit Ohmscher Widerstand des
Entladekreises
Ri Internal resistance Innenwiderstand
Rins Insulation resistance Isolationswiderstand
RP Parallel resistance Parallelwiderstand
RS Series resistance Serienwiderstand
S severity (humidity test) Schärfegrad (Feuchtetest)
t Time Zeit
T Temperature Temperatur
τ Time constant Zeitkonstante
tan δ Dissipation factor Verlustfaktor
tan δD Dielectric component of dissipation Dielektrischer Anteil des Verlustfaktors
factor
tan δP Parallel component of dissipation factor Parallelanteil des Verlfustfaktors
tan δS Series component of dissipation factor Serienanteil des Verlustfaktors
TA Temperature of the air surrounding the Temperatur der Luft, die das Bauteil
component umgibt
Tmax Upper category temperature Obere Kategorietemperatur
Tmin Lower category temperature Untere Kategorietemperatur
tOL Operating life at operating temperature Betriebszeit bei Betriebstemperatur und
and voltage -spannung
Top Operating temperature, TA + ΔT Beriebstemperatur, TA + ΔT
TR Rated temperature Nenntemperatur
Tref Reference temperature Referenztemperatur
tSL Reference service life Referenz-Lebensdauer

Please read Cautions and warnings and Page 36 of 39

Important notes at the end of this document.
 B32671L, B32672L
High V AC, high temperature (wound)

Symbol English German

VAC AC voltage Wechselspannung
VC Category voltage Kategoriespannung
VC,RMS Category AC voltage (Sinusförmige)
Kategorie-Wechselspannung
VCD Corona-discharge onset voltage Teilentlade-Einsatzspannung
Vch Charging voltage Ladespannung
VDC DC voltage Gleichspannung
VFB Fly-back capacitor voltage Spannung (Flyback)
Vi Input voltage Eingangsspannung
Vo Output voltage Ausgangssspannung
Vop Operating voltage Betriebsspannung
Vp Peak pulse voltage Impuls-Spitzenspannung
Vpp Peak-to-peak voltage Impedance Spannungshub
VR Rated voltage Nennspannung
R Amplitude of rated AC voltage Amplitude der Nenn-Wechselspannung
VRMS (Sinusoidal) alternating voltage, (Sinusförmige) Wechselspannung
root-mean-square value
VSC S-correction voltage Spannung bei Anwendung "S-correction"
Vsn Snubber capacitor voltage Spannung bei Anwendung
"Beschaltung"
Z Impedance Scheinwiderstand
Lead spacing Rastermaß

Please read Cautions and warnings and Page 37 of 39

Important notes at the end of this document.
Important notes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, we are either unfamiliar with individual customer applications or less familiar with
them than the customers themselves. For these reasons, it is always ultimately incumbent on
the customer to check and decide whether a product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet ([Link]/material). Should you have
any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to our General
Terms and Conditions of Supply.

Page 38 of 39
Important notes

7. Our manufacturing sites serving the automotive business apply the IATF 16949 stan-
dard. The IATF certifications confirm our compliance with requirements regarding the quality
management system in the automotive industry. Referring to customer requirements and cus-
tomer specific requirements (“CSR”) TDK always has and will continue to have the policy of
respecting individual agreements. Even if IATF 16949 may appear to support the acceptance
of unilateral requirements, we hereby like to emphasize that only requirements mutually
agreed upon can and will be implemented in our Quality Management System. For clari-
fication purposes we like to point out that obligations from IATF 16949 shall only become
legally binding if individually agreed upon.
8. The trade names EPCOS, CarXield, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas,
CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue,
MiniCell, MKD, MKK, ModCap, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap,
PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID,
SineFormer, SIOV, ThermoFuse, WindCap, XieldCap are trademarks registered or pend-
ing in Europe and in other countries. Further information will be found on the Internet at
[Link]/trademarks.

Release 2020-06

Page 39 of 39