SIMPLY CLEVER

ŠKODA Citigo
Owner's Manual
 Layout of this Owner's Manual For the sake of the environment

(explanations) An Environmental note draws your attention to environmental protection aspects.

This is where you will, for example, find tips aimed at reducing your fuel consump-
tion.
This Owner's Manual has been systematically designed to make it easy for you to
search for and obtain the information you require.
Note
Chapters, table of contents and subject index
The text of the Owner's manual is divided into relatively short sections which are A normal Note draws your attention to important information about the operation
combined into easy-to-read chapters. The chapter you are reading at any particular of your vehicle.
moment is always specified on the bottom right of the page.
The Table of contents is arranged according to the chapters and the detailed Sub-
ject index at the end of the Owner's Manual helps you to rapidly find the informa-
tion you are looking for.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of
travel of the vehicle.
Units of measurement
All values are expressed in metric units.
Explanation of symbols
 Denotes a reference to a section with important information and safety
advice in a chapter.
 Denotes the end of a section.
 Denotes the continuation of a section on the next page.
 Indicates situations where the vehicle must be stopped as soon as possi-
ble.
® Denotes a registered trademark.
Notes
WARNING
The most important notes are marked with the heading WARNING. These
WARNING notes draw your attention to a serious risk of accident or injury.

CAUTION
A Caution note draws your attention to the possibility of damage to your vehicle
(e.g. damage to gearbox), or points out general risks of an accident.
 Preface

You have opted for a ŠKODA – our sincere thanks for your confidence in us.
You have received a vehicle with the latest technology and range of amenities. Please read this Owner's
Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use
of the vehicle.
Observe the national legal requirements when using your vehicle.
If you have any questions about your vehicle, please contact a ŠKODA Partner.
We hope you enjoy driving your ŠKODA, and wish you a pleasant journey at all times.
Your ŠKODA AUTO a.s. (Hereinafter referred to only as ŠKODA or manufacturer) 
On-board literature If the service schedule is missing or in poor condition, please contact the special-
The on-board literature for your vehicle consists of this “owner's manual” as well ist garage that regularly services your vehicle. You will need to request a dupli-
as a “service schedule” and the “Help on the road” brochure. cate, in which the specialist garage will confirm the service work previously car-
ried out.
Depending on the vehicle model and equipment, other additional operating man-
uals and instructions may be provided (e.g. an operating manual for the radio). The Help on the road brochure
If one of the documents listed above is missing, please contact a ŠKODA Partner. The Help on the road brochure contains the most important emergency tele-
phone numbers as well as telephone numbers and contact addresses of ŠKODA
Terms used Partners in the various different countries.
The on-board literature contains the following terms relating to the service work
for your vehicle.
› “Specialist garage” - a company that carries out specialist service tasks for
ŠKODA vehicles
› “ŠKODA service partner” - a company that is contractually authorized by ŠKODA
AUTO a.s. to carry out service tasks for ŠKODA vehicles
› “ŠKODA Partners” - a company that is authorized by ŠKODA AUTO a.s. to sell
ŠKODA products or carry out service work, or to carry out these tasks in parallel
The owner's manual
This owner's manual describes all possible equipment variants without identify-
ing them as special equipment, model variants or market-dependent equipment.
Consequently, this vehicle does not need to contain all of the equipment compo-
nents described in this owner's manual.
The scope of equipment in your vehicle relates to your sales contract for the vehi-
cle. More information is available from the ŠKODA Partner where you bought the
vehicle.
The illustrations may differ in minor details from your vehicle; they are only inten-
ded as general information.
The service schedule:
› Contains vehicle data including information on service work carried out;
› Is intended as proof of services carried out;
› Is intended for records relating to the mobility warranty (only valid for some
countries);
› Serves as a warranty certificate from the ŠKODA Partner where your vehicle
was purchased.
Therefore please always present the service schedule when you take your vehicle
to a specialist garage.
 Heating and air-conditioning 55 Airbag system 95
Table of Contents Heating, ventilation, cooling 55 Description of the airbag system 95
Heating 56 Airbag overview 96
Air conditioning system 57 Deactivating airbags 98
Abbreviations
Communication and multimedia 60 Transporting children safely 100
Telephone and Move & Fun 60 Child seat 100
Using the system Fastening systems 102
Cockpit 7 Driving
Overview 6 General Maintenance
Starting-off and Driving 63
Instruments and warning lights 8 Starting and stopping the engine 63 Taking care of and cleaning the vehicle 105
Instrument cluster 8 Braking 65 Washing your car 105
Multifunction display (onboard computer) 11 Manual gear changing and pedals 67 Taking care of your vehicle exterior 106
Warning lights 14 Automatic gearbox 67 Taking care of the interior 110
Unlocking and locking 20 Running in 70 Modifications, repairs and technical alterations 112
Unlocking and locking 20 Economical driving and environmental
Inspecting and replenishing 115
sustainability 71
Central locking system 23 Fuel 115
Avoiding damage to your vehicle 75
Remote control 25 Vehicles with CNG (compressed natural gas)
Driving abroad 76
Luggage compartment lid 26 mode 116
Window operation 27 Assist systems 77 Engine compartment 120
Power sliding/tilting roof 29 Brake assist systems 77 Engine oil 123
Parking aid 78 Coolant 125
Lights and visibility 31
Cruise Control System 80 Brake fluid 126
Lights 31
START/STOP 82 Vehicle battery 127
Interior lighting 34
City Safe Drive 83
Visibility 35 Wheels 131
Windscreen wipers and washers 36 Tyres and wheel rims 131
Rear window 38
Safety Winter operation 136
Seats and stowing 40 Passive Safety 87
Front seats 40 General information 87 Do-it-yourself
Rear seats 42 Correct seated position 88
Emergency equipment and self-help 137
Luggage compartment 44 Seat belts 91 Emergency equipment 137
Roof rack system 47 Using seat belts 91 Changing a wheel 138
Useful equipment 48 Inertia reels and belt tensioners 93 Breakdown kit 142
Storage compartments 51

Table of Contents 3
 Jump-starting 144
Towing the vehicle 146
Fuses and light bulbs 148
Fuses 148
Bulbs 151

Technical data
Technical data 155
Vehicle data 155

Index

4 Table of Contents
Abbreviations
Abbreviation Definition
rpm Engine revolutions per minute
ABS Anti-lock brake system
ASG Automated transmission
CNG Compressed natural gas
CO2 in g/km discharged quantity of carbon dioxide in grams per driven kilo-
metre
EDL Electronic differential lock
EPC EPC fault light
ESC Electronic Stability Control
kW Kilowatt, measuring unit for the engine output
MG Manual gearbox
MFD Multifunction display
Nm Newton meter, measuring unit for the engine torque
TCS Traction control 

Abbreviations 5
 Fig. 1 Cockpit

6 Using the system

 22 Light switch 31
Using the system 23 Bonnet release lever 120
24 Regulator for headlamp beam adjustment for the headlights 32
25 Lever for adjusting the steering wheel 64
Cockpit 26 Ignition lock 65
27 Pedals 67
Overview 28 Regulator for left seat heating 42
29 Radio
1 Door opening lever on the driver's side 22 30 Button for City Safe Drive system 83
2 Electrical power window in the driver's door 27 31 Handbrake lever 66
3 Central locking system 24 32 Depending on equipment fitted:
4 Electric exterior mirror adjustment 39 › Gearshift lever (manual gearbox) 67
5 Air outlet vent on the driver's side 55 › Selector lever (automated gearbox) 69
6 Operating lever: 33 Storage compartment 53
› Turn signal lights and main beam, headlight flasher 32 34 Regulator for right seat heating 42
› Speed regulating system 80
7 Steering wheel: Note
› With horn Cars with factory-fitted radio are supplied with separate instructions for operat-
› With driver’s front airbag 96
■
ing such equipment.
8 Instrument cluster: Instruments and warning lights 8 ■ The arrangement of the controls and switches and the location of some items
9 Operating lever: on right-hand drive models may differ from that shown in » Fig. 1. The symbols on
› Multifunction display 11 the controls and switches are the same as for left-hand drive models. 
› Windscreen wiper and wash system 36
10 Switch for rear window heater 35
11 START-STOP button 82
12 Depending on equipment fitted:
› Operating controls for the heating 56
› Operating controls for the air conditioning system 57
13 Socket for the cradle for the multifunction device Move & Fun 61
14 Warning light for the deactivated front seat passenger airbag 99
15 Interior mirror 38
16 Switch for hazard warning lights 33
17 Storage compartment on the front passenger side 52
18 Front passenger airbag 96
19 Air outlet vent on the front passenger side 55
20 Power window in the front passenger door 27
21 Door opening lever on the front passenger side 22

Cockpit 7
 Overview of the Instrument cluster
Instruments and warning lights

Instrument cluster

 Introduction
This chapter contains information on the following subjects:
Overview of the Instrument cluster 8
Speedometer 9
Fuel gauge 9
Engine revolutions counter 9
Counter for distance driven 10
Service Interval Display 10
Recommended gear 10 Fig. 2 Instrument cluster - Version 1

WARNING
■ Concentrate fully at all times on your driving! As the driver you are fully re-
sponsible for the operation of your vehicle.
■ Never operate the controls in the instrument cluster while driving, only
when the vehicle is stationary! 

Fig. 3 Instrument cluster - Version 2

 First read and observe the introductory information and safety warn-
ings on page 8.

1 Speedometer » page 9
2 Display:
› With counter for distance driven » page 10
› with outside temperature display » page 12 

8 Using the system

 ›
3
›
With service interval display » page 10
With multifunction display » page 11
Reset button for the display of the daily trip counter (trip) » page 10
 First read and observe the introductory information and safety warn-
ings on page 8.

Vehicles running on petrol

4 Fuel gauge » page 9
The fuel gauge » Fig. 4 only operates if the ignition is switched on.
5 Engine revolutions counter » page 9
6 Adjust button for the clock » page 12  The fuel tank has a capacity of about 35 litres. If the fuel gauge in the fuel tank
reaches the reserve capacity level, the warning symbol  » Fig. 4 -  will appear
in the Instrument cluster. or the symbol  will flash for 10 seconds together with
Speedometer the remaining segments in the instrument cluster display » Fig. 4 - . There are
now about 4 litres of fuel remaining in the tank. This symbol is a reminder for you,
that you must refuel.
 First read and observe the introductory information and safety warn-
ings on page 8. An audible signal sounds as a warning signal.
The speed is shown in km/h or mph and km/h depending on the vehicle.  Vehicles running on CNG (compressed natural gas)
The fuel gauge » Fig. 5 only operates if the ignition is switched on.
When the vehicle runs on petrol, the pointer of the fuel gauge is in the range
Fuel gauge 1 » Fig. 5. When the vehicle runs on CNG, the pointer of the fuel gauge is in the
range 2 .
If the fuel level in the fuel tank for petrol reaches the reserve level, the warning
symbol  will appear in the instrument cluster. The pointer is in the red range of
the gauge 1 » Fig. 5. There are now about 5 litres of fuel remaining in the tank.
If the fuel level in the fuel tank for CNG reaches the reserve level, the warning
symbol  will appear in the instrument cluster. The pointer is in the red range of
the gauge 2 » Fig. 5. There are now about 1.5 kg of fuel remaining in the tank. 

Engine revolutions counter

Fig. 4 Fuel gauge
 First read and observe the introductory information and safety warn-
ings on page 8.
Fig. 5
The red scale of the rev counter 5 » Fig. 3 on page 8 indicates the range in which
Fuel gauge - CNG
the engine control unit begins to limit the engine speed. The engine control unit
restricts the engine speed to a steady limit.
Before reaching the red zone of the rev counter scale, shift up into the next high-
er gear.
To maintain the optimum motor speed, observe the gearshift indica-
tor » page 10. 

Instruments and warning lights 9

Avoid high engine speeds during the running-in period and before the engine has
Note
warmed up to the operating temperature .
■ Information is retained in the Service Interval Display even after the vehicle bat-
For the sake of the environment tery is disconnected.
■ If the instrument cluster is exchanged after a repair, the correct values must be
Shifting to a higher gear in good time helps to lower fuel consumption, minimises entered in the counter for the Service Interval Display. This work is carried out by
operating noise levels, protects the environment and contributes to a longer life a specialist garage.
and reliability of the engine. 
■ For more information on the service intervals, see » service schedule, chap-
ter service intervals. 

Counter for distance driven

Recommended gear
 First read and observe the introductory information and safety warn-
ings on page 8.
 First read and observe the introductory information and safety warn-
ings on page 8.
The distance which you have driven with your vehicle is shown in kilometres (km).
In some countries the measuring unit “mile” is used. An information for the engaged gear is shown in the display of the instrument
Reset button cluster.
To toggle between the odometer and the daily trip counter, briefly press the but- In order to minimise the fuel consumption, a recommendation for shifting into an-
ton 3 » Fig. 2 on page 8 or » Fig. 3 on page 8. other gear is indicated in the display.
To reset the display of the daily trip counter, press button 3 for longer. Show Importance
Daily trip counter (trip)
The daily trip counter indicates the distance which you have driven since it was  Optimal gear.
last reset - in steps of 100 metres or 1/10 of a mile.
Odometer  Recommends that you shift to a higher gear.
The odometer indicates the total distance in kilometres or miles which the vehicle
has been driven. 
 Recommends that you shift to a lower gear.

Service Interval Display CAUTION

The driver is always responsible for selecting the correct gear in different driving

 First read and observe the introductory information and safety warn-
ings on page 8.
situations, such as overtaking. 

Before the next service interval, the message  appears for some seconds and
the remaining kilometres are indicated after switching on the ignition.
At the time of the service, an acoustic signal will sound and the message ap-
pears for a few seconds after switching on the ignition.

10 Using the system

 Multifunction display (onboard computer) Memory

 Introduction Fig. 6
Multifunction display
This chapter contains information on the following subjects:
Memory 11
Operation 12
Digital clock 12
Multifunction display details 12
Warning against excessive speeds 13
The multifunction display can only be operated when the ignition is switched on.
After the ignition is switched on, the function displayed is the one which you last
selected before switching off the ignition.
 First read and observe the introductory information and safety warn-
ings on page 11.

The multi-functional indicator appears in the display » Fig. 6 on page 11. The multifunction display is equipped with two automatic memories. The selected
memory is shown in the Display » Fig. 6.
WARNING The data of the single-trip memory (memory 1) is shown if a 1 appears in the dis-
play. A 2 shown in the display means that data relates to the total distance mem-
■ Concentrate fully at all times on your driving! As the driver you are fully re-
ory (memory 2).
sponsible for the operation of your vehicle.
■ Do not only rely upon the information given on the outside temperature dis- Switching over the memory takes place with the button B » Fig. 7 on page 12
play that there is no ice on the road. Even at temperatures around +4 °C, black on the windscreen wiper lever.
ice may still be on the road surface – warning, drive with care!
Single-trip memory (memory 1)
The single-trip memory collates the driving information from the moment the ig-
Note nition is switched on until it is switched off. New data will also flow into the cal-
culation of the current driving information if the trip is continued within 2 hours
In certain national versions the displays appear in the Imperial system of meas- after switching off the ignition. If the trip is interrupted for more than 2 hours,
ures. 
the memory is automatically erased.
Total-trip memory (memory 2)
The total distance driven memory gathers data from any number of individual
journeys up to a total of 19 hours and 59 minutes driving or 1 999 kilometres driv-
en. The memory is deleted when either of these limits is reached and the calcula-
tion starts all over again.
Unlike the single-trip memory, the total-trip memory is not deleted after a period
of interruption of driving of 2 hours. 

Instruments and warning lights 11

 Note Digital clock
All information in the memory 1 and 2 is erased if the battery of the vehicle is dis-
connected. 
 First read and observe the introductory information and safety warn-
ings on page 11.

The time is set as follows:

Operation
› Press the rocker switch A » Fig. 7 on page 12 up or down to change the display
of the time.
Fig. 7 › Press the button 6 » Fig. 3 on page 8 to select the hour display so that it flash-
Multifunction display: Control el- es.
ements › Press button 3 to continue setting the time. Keep the button pressed to run
through the numbers quickly.
› Press the button 6 to select the minutes display so that it flashes.
› Press button 3 to continue setting the time. Keep the button pressed to run
through the numbers quickly.
› Confirm the set value by pressing the button 6 again, or wait for around 5 sec-
onds. The setting is saved automatically (the value stops flashing). 

 First read and observe the introductory information and safety warn-
ings on page 11. Multifunction display details
The rocker switch A and the button B are located on the windscreen wiper lev-
er » Fig. 7.  First read and observe the introductory information and safety warn-
ings on page 11.
Select memory Outside temperature
› Press the button B » Fig. 7. The current outside temperature is shown in the display.
Selecting functions If the outside temperature drops below +4 °C, the temperature indicator appears
› Briefly press the rocker switch A » Fig. 7 up or down. This opens the individual and a snow flake symbol (black ice warning) flashes for a few seconds, then re-
functions of the multifunction display one after the other. mains displayed together with the outside temperature.
Resetting Driving time
› Select the desired memory. The driving time which has elapsed since the memory was last erased, appears in
› Press the button B » Fig. 7 for longer. the display » page 11. If you want to measure the driving time from a particular
The following readouts of the selected memory will be set to zero by button B : moment in time on, at this moment, reset the memory by setting the button
B » Fig. 7 on page 12 to zero.
› Average fuel consumption
› Distance driven The maximum distance indicated in both memories is 19 hours and 59 minutes.
› Average speed The indicator is set back to zero if this period is exceeded. 
› Driving time 

12 Using the system

Current fuel consumption Average speed
The current fuel consumption level is shown in the display in litres/100 km1). You The average speed since the memory was last erased is shown in the display
can use this information to adapt your driving style to the desired fuel consump- in km/hour » page 11. If you wish to determine the average speed over a certain
tion. period of time, you must set the memory to zero at the start of the measurement
using the button B on the windscreen wiper lever » Fig. 7 on page 12.
The display appears in litres/hour if the vehicle is stationary or driving at a low
speed2). After erasing the memory, no value appears in the display until you have driven
approx. 300 m.
Average fuel consumption
The average fuel consumption since the memory was last erased is shown in the The display is updated regularly while you are driving.
display in litres/100 km1 ) » page 11. You can use this information to adapt your
Current speed
driving style to the desired fuel consumption.
The current speed which is identical to the display of the speedometer 1 » Fig. 3
If you wish to determine the average fuel consumption over a certain period of on page 8 is indicated on the display.
time, you must set the memory at the start of the new measurement to zero us-
ing the button B » Fig. 7 on page 12. A zero appears in the display for the first Coolant temperature
approx. 300 m you drive after erasing the memory. The current coolant temperature is shown in the display. 

The display is updated regularly while you are driving.

Range
Warning against excessive speeds
The estimated range in kilometres is shown on the display. It indicates the dis-
tance you can still drive with your vehicle based on the level of fuel in the tank
and the same style of driving.
 First read and observe the introductory information and safety warn-
ings on page 11.

The display is shown in steps of 10 km. After lighting up of the warning light for Adjust the speed limit while the vehicle is stationary
the fuel reserve the display is shown in steps of 5 km. › With button A » Fig. 7 on page 12, choose the menu point Warning against ex-
cessive speeds.
The fuel consumption over the last 50 km is used to calculate the range. The › Press the button B to activate the ability to set the speed limit (value flashes).
range will increase if you drive in a more economical manner. › Use the button A to set the required speed limit, e.g. 50 km/h.
Distance travelled › Confirm the speed limit that was set with button B , or wait approx. 5 seconds
The distance driven since the memory was last erased appears in the dis- until the setting is saved automatically (the value stops flashing).
play » page 11. If you want to measure the distance travelled from a particular mo- This allows you to set the speed in 5 km/h intervals.
ment in time on, at this moment, reset the memory by setting the button
B » Fig. 7 on page 12 to zero. Adjusting the speed limit while the vehicle is moving
› With button A » Fig. 7 on page 12, choose the menu point Warning against ex-
The maximum distance indicated in both memories is 1 999 km. The indicator is cessive speeds.
set back to zero if this period is exceeded. › Drive at the desired speed, e.g. 50 km/h.
› Press button B to accept the current speed as the speed limit (the value flash-
es). 

1) On some models in certain countries, the display appears in kilometres/litre.

2) On some models in certain countries, the display appears in --,- kilometres/litres if the vehicle is sta-
tionary.

Instruments and warning lights 13

If you wish to change the set speed limit, it is changed in 5 km/h intervals (e.g. the  Cruise control system 19
accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).  Main beam 19
› Confirm the speed limit that was set by pressing button B again, or wait ap- / Seat belt fastened/not fastened (belt status display) - Rear seat 19
prox. 5 seconds until the setting is saved automatically (the value stops flash-  City Safe Drive 19
ing).  START STOP 19
Change or delete speed limit The warning lights show certain functions/faults and may be accompanied by au-
› With button A » Fig. 7 on page 12, choose the menu point Warning against ex- dible signals.
cessive speeds.
› Pressing the button B deletes the speed limit. WARNING
› Pressing the button B activates the ability to change the speed limit.
■ If illuminated warning lights and the corresponding descriptions and warn-
If the set speed limit is exceeded, an audible signal will sound as a warning. At ing notes are not observed, this may result in severe injuries or major vehicle
the same time the message Warning against excessive speeds appears on the damage.
display with the set limit value. ■ The engine compartment of your car is a hazardous area. There is a risk of
The set speed limit value remains stored even after switching off the ignition.  injuries, scalding, accidents and fire when working in the engine compart-
ment, e.g. inspecting and replenishing oil and other fluids. It is essential to ob-
serve safety notes » page 120, Engine compartment. 

Warning lights
 Handbrake
 Introduction
This chapter contains information on the following subjects:
 Handbrake 14
 First read and observe the introductory information and safety warn-
ings on page 14.

The warning light  comes on if the handbrake is applied. An audible warning is

Braking system 14
also given if you drive the vehicle for at least 3 seconds at a speed of more than
 Seat belt warning light 15
6 km/h. 
 Generator 15
 Engine oil pressure 15
 Coolant temperature/coolant level 16  Braking system
  Electromechanical power steering 16
 Electronic Stability Control (ESC)
 Traction Control System (TC)
16
17  First read and observe the introductory information and safety warn-
ings on page 14.
Antilock brake system (ABS) 17 The warning light  illuminates if the brake fluid level is too low or there is a
 Rear fog lights 17 fault in the ABS.
 Exhaust inspection system 17
Stop the vehicle, switch off the engine, and check the level of the brake flu-
 EPC fault light 17
id » page 127.
 Airbag system 18
    Automated transmission 18 Further information » page 65. 

  Turn signal system 18

14 Using the system

 WARNING WARNING
■ If you have to stop for technical reasons, then park the vehicle at a safe dis- If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning tance from the traffic, switch off the engine and activate the hazard warning
light system » page 33. light system » page 33.
■ The following guidelines should be observed when opening the bonnet and
checking the brake fluid level » page 120, Engine compartment.
■ If the warning light  is displayed simultaneously with warning light CAUTION
 » page 17, Antilock brake system (ABS),  do not continue your jour- If the warning light  (cooling system fault) comes on in addition to the warning
ney! Seek help from a specialist garage. light  in the display when driving, stop the vehicle immediately and switch the
■ A fault to the braking system can increase the vehicle's braking distance! 
engine off – risk of engine damage! 

 Seat belt warning light  Engine oil pressure

 First read and observe the introductory information and safety warn-
ings on page 14.  First read and observe the introductory information and safety warn-
ings on page 14.

The warning light  comes on after the ignition is switched on as a reminder for The warning light  comes on for a few seconds when the ignition is switched
the driver and front passenger to fasten the seat belt. The warning light only on.
goes out if the driver or front passenger has fastened his seat belt. Stop the vehicle and switch the engine off if the warning light does not go off
If the seat belt has not been fastened by the driver or front passenger, a perma- after the engine has started or flashes while driving. Check the oil level and top
nent warning signal sounds at vehicle speeds greater than 25 km/h and simulta- up with engine oil if necessary » page 124, Checking the oil level.
neously the warning light  flashes. An audible signal sounds as a warning signal.
If the seat belt is not fastened by the driver or front passenger during the next Do not continue your journey if for some reason it is not possible to top up the
90 seconds, the warning signal is deactivated and the warning light  lights up engine oil under the prevailing conditions. This can cause serious engine damage.
permanently. Therefore, switch the engine off and seek help from a specialist garage.
Further information » page 91, Seat belts. 
Even if the oil level is correct,  do not drive any further if the warning light is
flashing. Also do not leave the engine running at an idling speed.

 Generator Seek help from a specialist garage.

 First read and observe the introductory information and safety warn-
ings on page 14.
WARNING
If you have to stop for technical reasons, then park the vehicle at a safe dis-
If the warning light lights up  when the engine is running, the vehicle battery is tance from the traffic, switch off the engine and activate the hazard warning
not being charged. light system » page 33, Hazard warning light system. 

Seek help from a specialist garage. The electrical system requires checking.

Instruments and warning lights 15

 CAUTION   Electromechanical power steering
The red oil pressure light  is not an oil level indicator! One should therefore
check the oil level at regular intervals, preferably after every refuelling stop. 
 First read and observe the introductory information and safety warn-
ings on page 14.

The warning light  comes on for a few seconds when the ignition is switched
 Coolant temperature/coolant level on.

 First read and observe the introductory information and safety warn-
ings on page 14.
If the warning light after switching on the ignition or when driving lights up con-
tinuously, a fault exists in the electromechanical power steering.
› If the yellow warning light lights up , this indicates a partial failure of the
The warning light  comes on for a few seconds when the ignition is switched power steering and the steering forces can be greater.
on.
› If the red warning light lights up , this indicates a complete failure of the pow-
If the warning light  lights up or flashes, either the coolant temperature is too er steering and the steering assist has failed (significantly higher steering
high or the coolant level is too low. forces).
An audible signal sounds as a warning tone. Further information » page 64.
Stop the vehicle, switch off the engine, check the level of the coolant » page 126,
and refill the coolant if necessary » page 126. Note
Do not continue your journey if for some reason it is not possible to top up the ■ If the yellow warning light  goes out after starting the engine again and driv-
coolant under the prevailing conditions. This can cause serious engine damage. ing a short distance, it is not necessary to visit a specialist garage.
Therefore, switch the engine off and seek help from a specialist garage. ■ If the vehicle battery has been disconnected and reconnected, the yellow warn-
ing light  comes on after switching on the ignition. The warning light should go
If the coolant is within the specified range, the increased temperature may be out after driving a short distance. 
caused by an operating problem at the radiator fan. Check the fuse for the radia-
tor fan, replace if necessary » page 150, Fuses in the engine compartment.
Do not continue driving if the warning light   does not go off even though the  Electronic Stability Control (ESC)
coolant level is correct and the fuse for the fan is in working order!
Seek help from a specialist garage.  First read and observe the introductory information and safety warn-
ings on page 14.

WARNING The warning light flashes to show that the ESC is currently operating.

If you have to stop for technical reasons, park the vehicle at a safe distance If the warning light  lights up, there is a fault in the ESC.
from traffic, switch off the engine and switch on the hazard warning light sys- As the ESC operates in conjunction with the ABS, the ESP warning light will also
tem » page 33.  come on if the ABS system fails.
If the warning light  comes on immediately after starting the engine, the ESC
can be switched off for technical reasons. In this case, the ESC can be switched
on again by switching the ignition on and off. If the warning light goes out, the
ESC is fully functional again.
Further information » page 77, Electronic Stability Control (ESC). 

16 Using the system

 Further information » page 78, Antilock Braking System (ABS).
Note
If the vehicle's battery has been disconnected and reconnected, the warning light WARNING
 comes on after switching on the ignition. The warning light should go out after
driving a short distance.  ■ If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 33.
■ If the warning light  » page 14 is displayed simultaneously with the ABS
 Traction Control System (TC)
warning light ,  do not continue your journey! Seek help from a specialist

 First read and observe the introductory information and safety warn-
ings on page 14.
garage.
■ The following guidelines should be observed when opening the bonnet and
checking the brake fluid level » page 120, Engine compartment. 
The warning light  comes on for a few seconds when the ignition is switched
on.
The warning light comes on when driving when a control cycle is activated.  Rear fog lights
The warning light illuminates permanently if there is a fault in the TCS.
The fact that the TCS operates together with the ABS means that the TCS warn-
ing light will also come on if the ABS system is not operating properly.
 First read and observe the introductory information and safety warn-
ings on page 14.

The warning light  comes on when the rear fog lights are operating » page 33. 
If the warning light  comes on immediately after starting the engine, the TCS
can be switched off for technical reasons. In this case, the TCS can be switched
on again by switching the ignition on and off. If the warning light goes out, the  Exhaust inspection system
TCS is fully functional again.
Further information » page 78, Traction Control System (TCS).
 First read and observe the introductory information and safety warn-
ings on page 14.
Note If the warning light  lights up, there is a fault in the exhaust inspection system.
If the vehicle's battery has been disconnected and reconnected, the warning light The engine control unit allows the vehicle to run in emergency mode.
 comes on after switching on the ignition. The warning light should go out after Seek help from a specialist garage. 
driving a short distance. 

 EPC fault light

 Antilock brake system (ABS)

 First read and observe the introductory information and safety warn-
ings on page 14.
 First read and observe the introductory information and safety warn-
ings on page 14.

If the warning light  lights up, there is a fault in the engine control. The engine
If the warning light  lights up, there is a fault in the ABS. control unit allows the vehicle to run in emergency mode.
The vehicle will only be braked by the normal brake system without the ABS. Seek help from a specialist garage. 

Seek help from a specialist garage.

Instruments and warning lights 17

 Warning light 
 Airbag system If the warning light  lights up and no gear can be selected, switch the ignition
on and off. If the warning light lights up after you switch on the ignition, seek as-
 First read and observe the introductory information and safety warn-
ings on page 14.
sistance from a specialist garage.
If the warning light  or warning light  lights up and an acoustic signal sounds,
Monitoring the airbag system this means that the automatic gearbox has overheated. Stop and allow the trans-
The warning light  comes on for a few seconds when the ignition is switched mission to cool down or drive more quickly than 20 km/h (12 mph).
on.
If the warning light  lights up again, switch off the vehicle, shut off the engine
There is a fault in the system if the warning light does not go out or flashes while and allow the gearbox to cool down.
driving » . This also applies if the warning light does not come on when the ig-
nition is switched on. Warning light 
If the warning light  lights up, operate the brake pedal.
The functionality of the airbag system is also monitored electronically when one
airbag has been switched off. Warning light 
If the warning light  lights up, operate the handbrake.
The following situation applies if the front or side airbag or belt tensioner have
been switched off using the vehicle system tester: Further information » page 67, Automatic gearbox.
› The warning light  lights up for around 4 seconds after switching on the igni-
tion and then flashes approximately another 12 seconds in 2 second intervals. WARNING
The following situation applies if the airbag has been switched off using the If you have to stop for technical reasons, park the vehicle at a safe distance
key switch for the airbag in the front passenger storage compartment: from traffic, switch off the engine and switch on the hazard warning light sys-
› The warning light  comes on for a few seconds when the ignition is switched tem » page 33. 
on;
› The deactivated airbag is indicated by the illumination of the warning light
     in the middle of the dash panel » page 99, Deactivating
the front passenger airbag.   Turn signal system

WARNING
If there is a fault, have the airbag system checked immediately by a specialist
 First read and observe the introductory information and safety warn-
ings on page 14.

garage. Otherwise, there is a risk that the airbag will not be deployed in the Either the left  or right  warning light flashes depending on the position of the
event of an accident. 
turn signal lever.
If a turn signal light fails, the warning light flashes at twice its normal rate.
Switching off the hazard warning light system is switched on will cause all of the
    Automated transmission turn signal lights as well as both warning lights to flash.
Further information » page 32, Turn signal and main beam light.


First read and observe the introductory information and safety warn-
ings on page 14.

Warning light 
Do not continue your journey if the warning light  lights up and an acoustic sig-
nal sounds. Switch off the engine and seek assistance from a specialist garage.

18 Using the system

  Cruise control system  City Safe Drive

 First read and observe the introductory information and safety warn-
ings on page 14.  First read and observe the introductory information and safety warn-
ings on page 14.

The warning light  comes on when the cruise control is operating » page 80.  If the City Safe Drive system is currently slowing the vehicle down automatically,
the warning light will flash  quickly.
If the City Safe Drive system is not currently available, or if there is a system fault,
 Main beam the warning light will flash  slowly.

 First read and observe the introductory information and safety warn-
ings on page 14.
When the City Safe Drive system is switched off while the vehicle is travelling at a
speed between 5–30 km/h (3-19 mph), the warning light   will light up in the
instrument cluster display.
The warning light  comes on when the main beam or headlight flasher are se-
lected » page 31.  If the City Safe Drive system is switched on, the warning light in the instrument
cluster display   will light up for around 5 seconds.
Further information » page 83, City Safe Drive. 
 / Seat belt fastened/not fastened (belt status display) -
Rear seat
 START STOP
 First read and observe the introductory information and safety warn-
ings on page 14.
 First read and observe the introductory information and safety warn-
ings on page 14.
After switching on the ignition, the belt status warning lights up for the rear
seats in the instrument panel display for 30 seconds and indicates whether any If the START STOP system is active, the warning light will light up .
rear seat passengers have fastened their seat belts. The belt status indicator will
If the START STOP system is active, but automatic engine shut down is not possi-
then light up when the passenger on the rear seat fastens or unfastens the seat
ble, the warning light will light up .
belt (when the ignition is switched on or during the journey).
When the warning light flashes  the START STOP system will not be available.
If the warning light , is switched on, the passenger on the rear seat has their
seat belt on. Further information » page 82, Function. 

If the warning light , is switched on, the passenger on the rear seat does not
have their seat belt on.
If a seat belt is unfastened on the rear seat during the journey at a speed of more
than 25 km/h, an acoustic signal will sound, and the belt status indicator for the
rear seats will flash for around 30 seconds.
Further information » page 91, Seat belts. 

Instruments and warning lights 19

 WARNING
Unlocking and locking
■ Always withdraw the key whenever you leave the vehicle – even if it is only
for a short time. This is particularly important if children are left in the vehicle.
Unlocking and locking The children might otherwise start the engine or operate electrical equipment
(e.g. power windows) – risk of injury!
■ Do not withdraw the ignition key from the ignition lock until the vehicle has
 Introduction
come to a stop. The steering lock might otherwise engage unintentionally –
This chapter contains information on the following subjects: risk of accident!

Vehicle key 20
Replacing the battery in the remote control key 21 CAUTION
Child safety lock 21 ■ Each key contains electronic components; therefore it must be protected
Opening/closing a door 22 against moisture and severe shocks.
Door opening lever 22 ■ Keep the groove of the keys absolutely clean. Impurities (textile fibres, dust,
Emergency locking of the doors 22  etc.) have a negative effect on the functionality of the locking cylinder and igni-
tion lock.
■ The function of the remote control may temporarily be affected by interference
Vehicle key from transmitters located near the vehicle that operate in the same frequency
range (e.g. mobile phones, television transmitters).
■ The battery must be replaced if the central locking does react to the remote
control at less than around 3 metres away » page 21.

Note
If you lose a key, please contact a specialist garage, who will be able to provide
you with a new one. 

Fig. 8 Key without remote control/key with remote control (remote control
key)

 First read and observe the introductory information given on page 20.

Two keys are provided with the vehicle. Depending on the equipment, your vehi-
cle can be equipped with keys without radio remote control » Fig. 8 –  or with
radio remote control » Fig. 8 – .

20 Using the system

 Replacing the battery in the remote control key Note
■ The system has to be synchronised, if the vehicle cannot be unlocked or locked
with the remote control key after replacing the battery » page 26.
■ If a key has an affixed decorative cover, this will be destroyed when the battery
is replaced. A replacement cover can be purchased from a ŠKODA Partner. 

Child safety lock

Fig. 10
Child safety locks on the rear
doors
Fig. 9 Remote control key: Remove cover/remove battery

 First read and observe the introductory information given on page 20.

Each remote control key contains a battery which is housed under the cover
B » Fig. 9. The battery needs replacing if red warning light » Fig. 8 on page 20 –
 does not go on when you press a button on the remote control key. We recom-
mend having the key batteries replaced by a specialist garage. However, if you
would like to replace the discharged battery yourself proceed as follows.  First read and observe the introductory information given on page 20.

› Flip out the key. The child safety lock prevents the rear door from being opened from the inside.
› Press off the battery cover with your thumb or using a flat screwdriver in the The door can only be opened from the outside.
region of arrows 1 » Fig. 9.
You can switch the child safety lock on and off using the vehicle key.
› Remove the discharged battery from the key by pressing the battery down-
wards in the region of arrow 2 . Switching on
› Insert the new battery. Ensure that the “+” symbol on the battery is facing up- › Turn the slot of the lock on the left-hand door clockwise » Fig. 10 – do the same
wards. The correct polarity is shown on the battery cover. anti-clockwise on the right-hand door.
› Place the battery cover on the key and press it down until it clicks into place.
Switching off
CAUTION › Turn the slot of the lock on the left-hand door anti-clockwise – do the same
clockwise on the right-hand door. 
■ Pay attention to the correct polarity when changing the battery.
■ The replacement battery must have the same specification as the original bat-
tery.

For the sake of the environment

Dispose of the used battery in accordance with national legal provisions.

Unlocking and locking 21

 Opening/closing a door
 First read and observe the introductory information given on page 20.

On vehicles without central locking, you can lock and unlock doors which do not
have a locking cylinder from the inside.
Locking
› Push the door opening lever in the direction of the arrow so that the red mark-
ing A » Fig. 12 is visible.
Unlocking
› Open the door by pulling the door opening lever once against the direction of
the arrow » Fig. 12. 

Fig. 11 Door handle/door opening lever:

Emergency locking of the doors

 First read and observe the introductory information given on page 20.

Opening from the outside

› Unlock the vehicle and pull on door handle A » Fig. 11 on the door you wish to
open.
Opening from the inside
› Pull on door opening lever B on the door you wish to open.
Closing from the inside
› Grasp pull handle C and close the door. 

Fig. 13 Emergency locking of the door

Door opening lever

Fig. 12
 First read and observe the introductory information given on page 20.

An emergency locking mechanism is located on the front of the doors that have
Door opening lever
no locking cylinder » Fig. 13 -  this mechanism is only visible after opening the
door.
Locking
› Insert the key into the slot » Fig. 13 -  and turn it clockwise into the vertical
position on the right-hand door » Fig. 13 -  and anti-clockwise on the left-hand
door.
After closing the door, it no longer be opened from the outside. The door can be
unlocked from the inside by pulling on the door handle again, and then opened
from the outside. 

22 Using the system

 Central locking system Note
■ In the event of an accident in which the airbags are deployed, the locked doors
 Introduction are automatically unlocked in order to enable rescuers to gain access to the vehi-
cle.
This chapter contains information on the following subjects: ■ If the central locking fails, only the driver's door can be locked or unlocked using
the key. The other doors and the luggage compartment can be locked or unlocked
Safe securing system 23
manually.
Unlocking the vehicle using the key 24 ■ Emergency locking of the door » page 22.
Locking the vehicle with the key 24 ■ Emergency unlocking of the luggage compartment lid » page 27. 
Vehicle locking/unlocking from the inside 24
When using central locking or unlocking, all doors are locked or unlocked simulta-
neously. The luggage compartment lid is unlocked. The luggage compartment lid
Safe securing system
can then be opened by pressing the button.
Automatic locking and unlocking
All the doors and the luggage compartment lid are locked automatically once the
 First read and observe the introductory information and safety warn-
ings on page 23.

car reaches a speed of about 15 km/h. The central locking system is equipped with a safe securing system. The door
locks are blocked automatically if the vehicle is locked from the outside. The
If the ignition key is withdrawn, the car is then automatically unlocked again. It is warning light flashes for around 2 seconds in quick succession, afterwards it be-
also possible for the driver to unlock the car by pressing the central locking but- gins to flash evenly at longer intervals. It is not possible to open the doors with
ton. the door handle either from the inside or from the outside. This acts as an effec-
The doors can be unlocked and opened from the inside by a single pull on the tive deterrent against attempts to break into your vehicle.
opening lever of the respective door. The safe securing system can be deactivated within 2 seconds by double locking
Automatic locking and unlocking can be activated by a specialist garage on re- the vehicle.
quest. If the safe securing system is not operating, the warning light in the driver door
flashes for about 2 seconds fast, goes out and starts to flash evenly at longer in-
WARNING tervals after about 30 seconds.
Locked doors prevent unwanted entry into the vehicle from outside, for exam- The safe securing system is activated again the next time the vehicle is unlocked
ple at road crossings. They do, however, make it more difficult for rescuers to and locked.
get into the vehicle in an emergency – risk to life! If the vehicle is locked and the safe securing system is deactivated, the door can
be opened from the inside by a single pull on opening lever of the respective
door. 

Unlocking and locking 23

 WARNING Locking the vehicle with the key
If the vehicle is locked from the outside and the safe securing system is acti-
vated, there must not be any person in the vehicle as it is then no longer pos-
sible to open either a door or a window from the inside. The locked doors
 First read and observe the introductory information and safety warn-
ings on page 23.
make it more difficult for rescuers to get into the vehicle in an emergency – › Turn the key in the locking cylinder of the driver's door in the opposite direction
risk to life! of travel (lock position) B » Fig. 14 on page 24.

› All the doors and the luggage compartment lid are locked.
Note › The switched on interior lights will switch off over the door contact.
You will be informed that the safe securing system has been activated after the
› The safe securing system is immediately activated.
vehicle has been locked by means of the message SAFE LOCK on the instrument
› The warning light in the driver door begins flashing.
cluster display. 
Note
If the driver's door has been opened, the vehicle cannot be locked. 
Unlocking the vehicle using the key

Fig. 14 Vehicle locking/unlocking from the inside

Turning the key for unlocking
and locking the vehicle Fig. 15
Central locking button

 First read and observe the introductory information and safety warn-
ings on page 23.

› Turn the key in the locking cylinder of the driver's door in the direction of travel
(unlocking position) A » Fig. 14.  First read and observe the introductory information and safety warn-
ings on page 23.
› Pull the door handle and open the door. If the vehicle was not locked from the outside, you can also unlock and lock it
› All the doors are unlocked. with the button » Fig. 15 without the ignition switched on.
› The luggage compartment lid is then unlocked. Locking all doors and the luggage compartment lid
› The switched on interior lights come on over the door contact. › Press the symbol button  » Fig. 15.
› The safe securing system is deactivated. 
Unlocking all doors and the luggage compartment lid
› Press the symbol button . 

24 Using the system

The following applies if your vehicle has been locked using the central locking The key has a fold-open key bit which can be used for unlocking and locking the
button. car manually and also for starting the engine.
› It is not possible to open the doors or the luggage compartment lid from the If a lost key is replaced or if the receiver unit has been repaired or replaced, the
outside (safety feature, e.g. when stopping at traffic lights etc.).
system must be initialised by a specialist garage. Only then can the remote con-
› The doors can be unlocked and opened from the inside by a single pull on the trol key be used again.
opening lever of the respective door.
› If at least one door has been opened, the vehicle cannot be locked. Note
› In the event of an accident in which the airbags are deployed, the locked doors
are automatically unlocked from the inside in order to enable rescuers to gain ■ The remote control is automatically deactivated when the ignition is switched
access to the vehicle. on.
■ The operation of the remote control may temporarily be affected by interfer-
WARNING ence from transmitters close to the car and which operate in the same frequency
range (e.g. mobile phone, TV transmitter).
The central locking system also operates if the ignition is switched off. Chil- ■ The battery must be replaced if the central locking or anti-theft alarm system
dren should never be left unattended in the vehicle since it is difficult to pro-
does react to the remote control at less than 3 metres away » page 21.
vide assistance from the outside when the doors are locked. Doors locked ■ If the driver door is open, the vehicle cannot be locked using the remote control
from the inside make it difficult for rescuers to get into the vehicle in an emer-
key. 
gency – risk to life!

Note Unlocking/locking
If the safe securing system is activated » page 23, the door opening lever and the
central locking buttons do not operate.  Fig. 16
Remote control key

Remote control

 Introduction
This chapter contains information on the following subjects:
Unlocking/locking 25
Synchronization
You can use the remote control key to:
26
 First read and observe the introductory information given on page 25.

Unlocking the vehicle 

› unlock and lock the vehicle, › Press the button 1 » Fig. 16.
› unlock the luggage compartment lid.
The transmitter with the battery is housed in the handle of the remote control Locking the vehicle 
key. The receiver is located in the interior of the vehicle. The operating range of › Press the button 3 » Fig. 16.
the remote control key is approx. 30 m. But this range of the remote control can Deactivating the safe securing system
be reduced if the batteries are weak. › Press the button 3 » Fig. 16 twice within 2 seconds. Further informa-
tion » page 23. 

Unlocking and locking 25

Unlocking the luggage compartment lid 
› Press the button 2 » Fig. 16. Further information » page 27. Synchronization

Folding out the key bit

› Press the button 4 » Fig. 16.  First read and observe the introductory information given on page 25.

Folding in the key bit If the vehicle cannot be unlocked by actuating the remote control system then it
› Press the button 4 » Fig. 16 and fold in the key bit. is possible that the code in the key and the control unit in the vehicle are no lon-
ger synchronised. This can occur when the buttons on the radio-operated key are
Unlocking actuated a number of times outside of the operative range of the equipment or
The turn signal lights flash twice as confirmation that the vehicle has been un- the battery on the remote control was replaced.
locked. If the vehicle is unlocked using button 1 and none of the doors or the
luggage compartment lid are opened within the next 30 seconds, the vehicle is This means it is necessary to synchronise the code as follows:
automatically locked again and the safe securing system is reactivated. This func- › press any button on the remote control key;
tion is intended to prevent the car being unlocked unintentionally. › pressing of the button means that the door will unlock with the key within 1 mi-
nute. 
Locking
The turn signal lights flash once to confirm that the vehicle has been correctly
locked.
Luggage compartment lid
If the doors or the luggage compartment lid remain open after the vehicle has
been locked, the turn signal lights do not flash until they have been closed.
 Introduction
WARNING This chapter contains information on the following subjects:
If the car is locked from the outside and the safe securing system is activated, Unlocking/opening and closing 27
there must not be any person in the car as it is then not possible to open ei- Emergency unlocking 27
ther a door or a window from the inside. The locked doors make it more diffi-
cult for rescuers to get into the vehicle in an emergency – risk to life! WARNING
■ Ensure that the lock is properly engaged after closing the luggage compart-
Note ment lid. Otherwise, the luggage compartment lid might open suddenly while
Only operate the remote control when the doors and luggage compartment lid driving, even if the luggage compartment lid lock was closed – risk of accident!
are closed and the vehicle is in your line of sight.  ■ Never drive with the luggage compartment lid open or ajar, as otherwise ex-
haust gases may get into the interior of the vehicle – risk of poisoning!
■ Do not press on the rear window when closing the luggage compartment lid,
as otherwise this could crack – risk of injury!

Note
A closed, but not locked luggage compartment lid is locked automatically when
driving off, or when travelling at speeds greater than about 9 km/h. It is unlocked
again after the vehicle stops and the door is opened. 

26 Using the system

 Unlocking/opening and closing Emergency unlocking

Fig. 18
Emergency unlocking of the lug-
gage compartment lid

Fig. 17 Luggage compartment lid

 First read and observe the introductory information and safety warn-
ings on page 26.

 First read and observe the introductory information and safety warn-
ings on page 26. The luggage compartment lid can be unlocked manually if there is a fault in the
central locking system.
Unlocking in vehicles without remote control
Unlocking
› Unlock the driver's door with the vehicle key » page 24. › Fold the rear seat backrest forward » page 43, Folding the rear seats forward.
Unlocking in vehicles with remote control › Insert the vehicle key or a similar tool into the opening A » Fig. 18 in the lid trim
› Press the  symbol button on the vehicle key. up to the stop.
Unlocking with the remote control key
› Unlock the lock in the direction of arrow.
› Press the  symbol button on the vehicle key until the luggage compartment › Open the luggage compartment lid. 

lid unlocks.
Opening Window operation
› Open the luggage compartment lid by pressing the » Fig. 17 -  button.
Closing  Introduction
› Reach into the recesses » Fig. 17 -  and pull the luggage compartment lid
down. This chapter contains information on the following subjects:
› Close the lid with a slight swing. 
Electric window opening/closing 28
Manually opening/closing rear windows 29 

Unlocking and locking 27

 WARNING Electric window opening/closing
■ If the vehicle is locked from the outside, do not leave anybody in the vehicle
as it is not possible to open the windows from the inside in the event of an Fig. 19
emergency. Button on the driver's door
■ When closing the windows, proceed with caution so as to avoid causing
crushing injuries - risk of injury!

CAUTION
■ Keep the windows clean to ensure the correct functionality of the electric win-
dows.
■ If the windows are frozen, first of all remove the ice » page 108, Windows and
exterior mirrors. Only then can the electrical power windows be operated, as oth-
erwise the window seal and the electrical power window mechanism could be
damaged.
 First read and observe the introductory information and safety warn-
ings on page 27.

■ Make sure that the windows are closed whenever you leave the locked vehicle. The electrical power windows can only be operated when the ignition is switched
on.
For the sake of the environment Opening
The windows must be kept closed at high speeds in order to prevent unnecessa-
› The window is opened by pressing lightly on the corresponding button. The
opening process stops when one releases the button.
rily high fuel consumption.
Closing
Note › The window is closed by pulling lightly on the corresponding upper edge of the
button. The closing process stops when one releases the button. 
The heating, air conditioning and ventilation system should be used to ventilate
the inside of the vehicle while driving. If the windows are open, dust as well as
other dirt can get into the vehicle, and there may also be wind noise at certain
speeds. 

28 Using the system

 The sliding/tilting roof can still be operated for approx. 10 minutes after switching
Manually opening/closing rear windows the ignition off. However, as soon as one of the front doors is opened it is no lon-
ger possible to operate the sliding/tilting roof.

Note
■ Always close the sliding/tilting roof before unhooking the battery.
■ If the battery has been disconnected and reconnected, it is possible that the
sliding/tilting roof does not operate correctly. Next, move the rotary switch into
position A » Fig. 21 on page 29, pull it, and hold onto the recess downwards
and forwards tightly. The sliding/tilting roof opens and closes again after around
10 seconds. Do not release the control dial until it has done so. 

Fig. 20 Rear windows

Operation

 First read and observe the introductory information and safety warn-
ings on page 27. Fig. 21
Control dial for the sliding/tilting
Opening roof
› Take hold of the safety in the recess » Fig. 20 -  and open the window in the
direction of the arrow.
› Lock the window in the opened position by pressing the safety in the direction
of arrow » Fig. 20 - .
Closing
› Take hold of the safety in the recess and pull it in the opposite direction of the
arrow » Fig. 20 - .
› Close the window in the initial position in the opposite direction of the ar-
row » Fig. 20 -  until the safety audibly latches.   First read and observe the introductory information given on page 29.

Comfort position
› Turn the switch to position C » Fig. 21.
Power sliding/tilting roof
Open partially
› Turn the switch to a position in area D » Fig. 21.
 Introduction
Open fully
This chapter contains information on the following subjects: › Turn the switch to position B » Fig. 21 and hold it in this position (spring-ten-
sioned position).
Operation 29
Tilting roof
The power sliding/tilting roof (abbreviated in the following as 'sliding/tilting roof'),
can only be operated with the rotary dial when the ignition is turned on » Fig. 21
› Turn the switch to position A » Fig. 21.
on page 29. The control dial has several positions.
› In order to tilt, press the switch in the region of the lug E towards the roof. 

Unlocking and locking 29

Closing
› Turn the switch to position A » Fig. 21.
› To close, press the switch on the recess E down and then push it forwards.
Force limiter
The sliding/tilting roof is fitted with a force limiter. The sliding/tilting roof stops
and moves back several centimetres when it cannot be closed because there is
something in the way (e.g. ice). The sliding/tilting roof can be fully closed without
a force limiter by pressing the switch on the recess down and then pushing it for-
ward until the sliding/tilting roof is fully closed » .

WARNING
Close the sliding/tilting roof carefully – risk of injury!

CAUTION
During the winter, any ice or snow in the vicinity of the sliding/tilting roof must be
removed before opening in order to prevent any damage to the opening mecha-
nism and seal.

Note
When the sliding/tilting roof is in the comfort position, the intensity of the wind
noise is reduced. 

30 Using the system

 Note
Lights and visibility
■ If the light switch is in the position , the ignition key is removed and the driv-
er's door is open, an audible warning signal will sound. The audible warning signal
Lights is switched off by means of the door contact when the driver's door is closed (ig-
nition off), however, the side lights remain on to illuminate the parked vehicle if
necessary.
 Introduction ■ The instruments are also illuminated when the side light or low beam light is

This chapter contains information on the following subjects: switched on.

■ In the event of cool or humid weather conditions, the headlights can be misted
Switching lights on and off 31 up from inside. The temperature difference between interior and external area of
Headlight beam adjustment 32 the headlight lenses is decisive. When the driving lights are switched on, the light
Function DAY LIGHT (daytime running lights) 32 outlet surfaces are free from mist after a short period, although the headlight
Turn signal and main beam light 32 lenses may still be misted up in the peripheral areas. It also concerns reverse light
Fog lights 33 and turn signal lights. This mist has no influence on the life of the lighting system. 
Rear fog light 33
Hazard warning light system 33
Switching lights on and off
Parking light 34
Unless otherwise stated, the lights only work when the ignition is on. Fig. 22
On models fitted with right-hand steering the position of certain switches differs Dash panel: Light switch
from that shown in » Fig. 22 on page 31. The symbols which mark the switch po-
sitions are identical, however.

WARNING
■ Never drive with only the side lights on! The side lights are not bright
enough to light up the road sufficiently in front of you or to be seen by other
oncoming traffic. Therefore always switch on the low beam when it is dark or
if visibility is poor.
■ The activation of the lights should only be undertaken in accordance with
national legal requirements.
 First read and observe the introductory information and safety warn-
ings on page 31.

■ The driver is always responsible for the correct settings and use of the Switching on the parking light
lights. › Turn the light switch » Fig. 22 to position .
Switching on the low beam and main beam
› Turn the light switch » Fig. 22 to position .
› Push the lever forwards to switch on the main beam » Fig. 24 on page 32.
Switching off lights (except daytime running lights)
› Turn the light switch » Fig. 22 to position 0. 

Lights and visibility 31

 Headlight beam adjustment Function DAY LIGHT (daytime running lights)

Fig. 23
Dash panel: Lights and visibility
 First read and observe the introductory information and safety warn-
ings on page 31.

Switching on daytime running lights

› Turn the light switch to position 0 » Fig. 22 on page 31.
When the daytime running lights are switched on, the lighting for the instrument
cluster is switched off, and the parking lights and the license plate light do not
light up. 

Turn signal and main beam light

 First read and observe the introductory information and safety warn-
ings on page 31.
Fig. 24
Turning the rotary switch » Fig. 23 from position - to 3 gradually activates the
Operating lever: Turn signal and
headlight beam adjustment, thereby shortening the beam of light.
main beam operation
Settings
The positions correspond approximately to the following car load.
- Front seats occupied, luggage compartment empty.
1 All seats occupied, luggage compartment empty.
2 All seats occupied, luggage compartment loaded.
3 Driver seat occupied, luggage compartment loaded.

WARNING  First read and observe the introductory information and safety warn-
ings on page 31.

Always adjust the headlight range adjustment in such a way that: The lever is also used to operate the parking light and the headlight flasher.
■ it does not dazzle other road users, especially oncoming traffic;
Right  and left  turn signal light
■ and the range is sufficient for safe driving.
› Push the lever » Fig. 24 upwards A or downwards B .
› If you only wish to flash three times (the "convenience turn signal"), briefly push
Note the lever to the upper or lower pressure point and release again.
› Turn signal for changing lanes – to only flash briefly, move the lever up or down
We recommend you adjust the headlight beam when the low beam is switched to the pressure point and hold it in this position.
on. 
Main beam 
› Switch on the low beam » page 31.
› Press the lever » Fig. 24 in the direction of arrow C .
› The main beam is switched off by pulling the lever into the initial position in the
direction of arrow D . 

32 Using the system

Headlight flasher 
› Pull the lever towards the steering wheel (spring-tensioned position) in the di- Rear fog light
rection of arrow D » Fig. 24 - the main beam and warning light  in the instru-
ment cluster come on.
 First read and observe the introductory information and safety warn-
ings on page 31.
CAUTION Switching on
Only use the main beam or the headlight flasher if other road users will not be › First of all, turn the light switch » Fig. 25 on page 33 to position  or .
dazzled. › Pull the light switch to position 2 .
If the vehicle is not fitted with fog lights » page 33, the rear fog light is switched
Note on by turning the light switch to the position  and is pulled out directly to the
position 2 . This switch does not have two positions, but only one position.
■ The turn signal system only operates when the ignition is switched on. The cor-
responding warning light  or  in the instrument cluster also flashes. The warning light  lights up in the instrument cluster when the rear fog light is
■ The turn signal is automatically cancelled after negotiating a curve. switched on » page 17,  Rear fog lights. 

■ An acoustic warning signal will sound when the driver's door is opened if the
lever is not in the middle position after removing the ignition key from the igni-
tion lock. The acoustic warning signal will stop just as soon as the driver's door is Hazard warning light system
closed. 

Fig. 26
Dash panel: Switch for hazard
Fog lights warning lights

Fig. 25
Dash panel: Light switch

 First read and observe the introductory information and safety warn-
ings on page 31.

› Press switch  » Fig. 26 to switch the hazard warning light system on or off.
 First read and observe the introductory information and safety warn-
ings on page 31.
All the turn signal lights on the vehicle flash at the same time when the hazard
warning light system is switched on. The warning light for the turn signals and
the warning light in the switch also flash at the same time. The hazard warning
Switching on
light system can also be operated if the ignition is switched off.
› First of all, turn the light switch » Fig. 25 to position  or .
› Pull the light switch into position 1 , the symbol  in the light switch lights up.  The hazard warning light system is switched on automatically if an airbag is de-
ployed in the event of an accident. 

Lights and visibility 33

 Note
The hazard warning light system must be switched on if, for example:
 First read and observe the introductory information given on page 34.

■you encounter a traffic congestion; Switching on

■your vehicle breaks down or an emergency situation occurs.  › Press the switch into position  » Fig. 27.
Switching off
› Press the switch into position O » Fig. 27.
Parking light
Operating with the door contact switch
› Press the switch into position  » Fig. 27.
 First read and observe the introductory information and safety warn-
ings on page 31.
If operating lights with the door contact switch is enabled, the light will come on
Parking light on both sides when:
› Turn the light switch » Fig. 25 on page 33 to position  and lock the vehicle.  › the vehicle is unlocked;
› one of the doors is opened;
› or the ignition key is removed.
Interior lighting If operating lights with the door contact switch is enabled, the light will go off
when:
› the vehicle is locked;
 Introduction › the ignition is switched on;
This chapter contains information on the following subjects:
› a few seconds after all the doors have been closed.
If a door remains open, or if the switch is in the position  the interior light goes
Interior light - Version 1 34 out after 10 minutes to prevent the battery from discharging. 
Interior light - Version 2 34 

Interior light - Version 2

Interior light - Version 1
Fig. 28
Fig. 27 Interior lighting – version 2
Interior lighting – version 1

 First read and observe the introductory information given on page 34.

Switching on
› Turn the switch A » Fig. 28 into the position . 

34 Using the system

Switching off
For the sake of the environment
› Turn the switch A » Fig. 28 into the 0 position.
The heating should be switched off as soon as the window is de-iced or free from
Operating with the door contact switch
mist. The reduced current consumption will have a favourable effect on fuel econ-
› Press the switch A » Fig. 28 into the middle (horizontal) position . omy.
Otherwise, the same principles apply as for version 1.
Reading lights Note
› Press switch B » Fig. 28 to switch the reading lights on or off. 
If the on-board voltage drops, the rear window heater switches off automatically,
in order to provide sufficient electrical energy for the engine control » page 130,
Automatic load deactivation. 

Visibility
Sun visors
 Introduction
This chapter contains information on the following subjects:
Rear window heater 35
Sun visors 35 

Rear window heater

Fig. 29
Switch for rear window heater
Fig. 30 Sun visor: Driver's side/front passenger's side

 First read and observe the introductory information given on page 35.

The sun visor for the driver or front passenger can be pulled out of the fixture and
swivelled towards the door in the direction of the arrow » Fig. 30.
The purpose of the strap A is to store small, light objects, such as a notepad, etc.

 First read and observe the introductory information given on page 35.
The front passenger sun visor has a vanity mirror B .

› The rear window heater is switched on or off by pressing the  » Fig. 29 symbol WARNING
switch; the warning light in the switch lights up or goes out.
The sun visors must not be swivelled towards the side windows and into the
The rear window heater only operates when the engine is running. deployment area of the side airbags if any objects are attached to them, such
The rear window heater switches off automatically after 10 minutes. as pens etc. If the side airbags are triggered, this could result in injuries to
people in the vehicle. 

Lights and visibility 35

 ■ Replace the windscreen wiper blades once or twice a year for safety reasons.
Windscreen wipers and washers These can be purchased from a ŠKODA Partner.
■ The ignition must not be switched on if the front windscreen wiper arms are fol-
 Introduction ded out. The wiper blades would move back into their rest position and while do-
ing so damage the paintwork of the bonnet.
This chapter contains information on the following subjects:
Operating the windscreen wipers and washers 36
Note
Replacing the windscreen wiper blades 37 ■ Periodic wiping is dependent on the driving speed. The faster the driver is go-
Replacing the rear windscreen wiper blade 38 ing, the more frequent the wiper action.
■ If there is an obstacle on the windscreen, the wiper will try to push away the
The windscreen wipers and the windscreen washer system only operate if the ig- obstacle. If the wiper is blocked by an obstruction, the wiper will remain station-
nition is switched on. ary. Remove the obstacle and switch the wiper on again.
The rear window is wiped once if the windscreen wipers are on when reverse ■ The capacity of the windscreen washer fluid reservoir is approximately 3 litres.
gear is selected. ■ The wiper blades should be cleaned on a regular basis with a windscreen clean-
er to avoid any smears. The wiper blades should be cleaned with a sponge or
Top up with windscreen wiper fluid » page 122.
cloth if they are heavily soiled by insect residues, for example. 

WARNING
■ Properly maintained windscreen wiper blades are essential for clear visibility Operating the windscreen wipers and washers
and safe driving » page 37.
■ Do not use the windscreen washer system at low temperatures, without
heating the windscreen beforehand. Otherwise the window cleaner could
freeze on the windscreen and restrict the view to the front.

CAUTION
■ In cold temperatures and during the winter, check before the journey or before
switching on the ignition that the wiper blades are not frozen to the windscreen.
If the windscreen wipers are switched on when the blades are frozen to the
windscreen, this may damage both the blades and windscreen wiper motor!
■ If the ignition is switched off while the windscreen wipers are switched on, the Fig. 31 Operating lever: Activating the windscreen wipers/rear window wip-
windscreen wipers will continue wiping in the same mode after the ignition is er
turned back on. The windscreen wipers could freeze up in cold temperatures be-
tween the time the ignition was turned off and when it was turned back on again.
■ Carefully detach frozen wiper blades from the front or rear window.
■ Remove snow and ice from the windscreen wipers before driving.
 First read and observe the introductory information and safety warn-
ings on page 36.

■ If the windscreen wipers are handled carelessly, there is a risk of damage to the Flick wipe
windscreen. › If you only wish to wipe the windscreen briefly, push the lever into the spring-
tensioned position 4 » Fig. 31. 

36 Using the system

Periodic wiping
› Position the lever upwards into position 1 » Fig. 31.  First read and observe the introductory information and safety warn-
ings on page 36.
Slow wipe Before replacing the windscreen wiper blade, put the windscreen wiper arms into
› Position the lever upwards into position 2 » Fig. 31. the service position.
Fast wipe Service position for changing wiper blades
› Position the lever upwards into position 3 » Fig. 31. › Closing the bonnet.
Automatic wipe/wash for windscreen › Switch the ignition off and on again.
› Pull the lever towards the steering wheel into the spring-tensioned position › Press the windscreen wiper lever into position 4 » Fig. 31 on page 36, the
5 » Fig. 31, the wash system and the windscreen wipers will operate. windscreen wiper arms will move into the service position.
› Release the lever. The windscreen wash system stops and the wiper continues Removing the wiper blade
for another 1-3 wiper strokes (depending on the period of spraying of the wind- › Raise the windscreen wiper arm from the rear window and slightly tilt the wind-
screen). screen wiper blade towards the wiper arm, arrow A » Fig. 32.
Wiping the rear window pane › Hold the windscreen wiper arm at the top end.
› Push the lever away from the steering wheel into position 6 » Fig. 31 and the › Unlock the locking button 1 and remove the wiper blade in the direction of ar-
windscreen wiper will operate every 6 seconds. row B .

Automatic wipe/wash for the rear window Attaching the wiper blade
› Push the lever away from the steering wheel into the spring-tensioned position › Push the windscreen wiper blade until the stop and it locks in place.
7 » Fig. 31, the windscreen wiper and wash system will operate. › Check that the wiper blade is correctly attached.
› Release the lever. The washer system stops and the wiper continues for anoth- › Fold the wiper arm back to the windscreen.
er 1-3 wiper strokes (depending on the duration of the spraying process). The › Turn on the ignition and press the windscreen wiper lever into position
lever will stay in position after releasing it 6 . 4 » Fig. 31 on page 36, the windscreen wiper arms move to the home position. 

Switching windscreen wipers off

› Move the lever back into the home position 0 » Fig. 31. 

Replacing the windscreen wiper blades

Fig. 32
Windscreen wiper blade

Lights and visibility 37

 Replacing the rear windscreen wiper blade Interior mirror

Fig. 33
Rear window wiper blade
 First read and observe the introductory information given on page 38.

Basic setting
› Pull the lever on the bottom edge of the mirror forward.
Dimming mirror
› Push the lever on the bottom edge of the mirror backwards. 

Additional interior mirror

 First read and observe the introductory information and safety warn-
ings on page 36. Fig. 34
Additional interior mirror
Removing the wiper blade
› Raise the windscreen wiper arm from the rear window and slightly tilt the wind-
screen wiper blade towards the wiper arm, arrow A » Fig. 33.
› Hold the windscreen wiper arm at the top end.
› Unlock the locking button 1 and remove the wiper blade in the direction of ar-
row B .
Attaching the wiper blade
› Push the windscreen wiper blade until the stop and it locks in place.
› Check that the wiper blade is correctly attached.
› Fold the wiper arm back to the windscreen.   First read and observe the introductory information given on page 38.

The additional interior mirror allows the driver a wider field of view of the rear
seats.
Rear window
Adjusting the angle
› Take hold of both the upper and lower edge of the mirror such that you are not
 Introduction touching the surface of the mirror.
› Adjust the mirror in direction of arrow to the desired position.
This chapter contains information on the following subjects:
Interior mirror 38 WARNING
Additional interior mirror 38 Concentrate fully at all times on your driving! As the driver you are fully re-
Exterior mirror 39  sponsible for the operation of your vehicle. Use the additional interior mirror
only to such an extent that you are in full control of your vehicle at any time. 

38 Using the system

 Folding in the exterior mirrors
Exterior mirror › Carefully fold in the entire body of the exterior mirror toward the side window,
fold it back from the side window until it audibly latches.

WARNING
■ Convex (curved outward) or a spherical exterior mirrors increase the vision
field. They do, however, make objects appear smaller in the mirror. These mir-
rors are therefore only of limited use for estimating distances to the following
vehicles.
■ Whenever possible use the interior mirror for estimating the distances to
the following vehicles.

Fig. 35 in the door, control knob/rotary knob: for the mechanical exterior Note
mirror/electrical exterior mirrors
■ Do not touch the surface of the exterior mirrors if the exterior mirror heater is
switched on.
 First read and observe the introductory information given on page 38.
■ If the power setting function fails at any time, the exterior mirrors can be set by
hand by pressing on the edge of the mirror surface.
Adjust the rear mirror before commencing to drive so that there is a clear view to ■ Contact a specialist garage if there is a fault with the power setting function for
the rear. the exterior mirrors. 

Mechanically-adjustable mirrors
› Use the control knob to adjust the surface of the mirror into the desired posi-
tion » Fig. 35 - . The movement of the mirror surface is identical to the move-
ment of the control knob.
Heating of the external mirror
› Place the rotary knob into the position  » Fig. 35 - .
The exterior mirror heater only operates when the engine is running and up to an
outside temperature of +20 °C.
Adjusting the left-hand exterior mirror
› Place the rotary knob into the position  » Fig. 35 - . The movement of the mir-
ror surface is identical to the movement of the rotary knob.
Adjusting the right-hand exterior mirror
› Place the rotary knob into the position . The movement of the mirror surface is
identical to the movement of the rotary knob.
Switching off operating control
› Place the rotary knob into the position .

Lights and visibility 39

 WARNING
Seats and stowing
As the driver, observe the following instructions.
■ Only adjust the driver's seat when the vehicle is stationary – risk of accident!
Front seats ■ Maintain a distance of at least 25 cm to the steering wheel. Not maintaining
this minimum distance will mean that the airbag system will not be able to
properly protect you – risk to life!
 Introduction ■ Ensure that there are no objects in the driver's footwell, as these may get

This chapter contains information on the following subjects: caught in the pedal apparatus when driving or braking. You would then no
longer be able to operate the clutch, brake or acceleration pedals.
Adjusting the front seats 41
Foldable front passenger seat 41
Front seat heating 42
WARNING

The driver's seat should be adjusted in such a way that the pedals can be fully As the front passenger, observe the following instructions.
pressed to the floor with slightly bent legs.
■ Maintain a distance of at least 25 cm to the dash panel. Not maintaining this
minimum distance will mean that the airbag system will not be able to proper-
The seat backrest on the driver's seat should be adjusted in such a way that the ly protect you – risk to life!
upper point of the steering wheel can be easily reached with slightly bent arms. ■ Always keep your feet in the footwell when the car is being driven – never

Correct adjustment of the seats is particularly important: place your feet on the instrument panel, out of the window or on the surfaces
› for safely and quickly reaching the controls; of the seats. You will be exposed to increased risk of injury if it becomes nec-
› for a relaxed body position that reduces fatigue; essary to apply the brake or in the event of an accident. If an airbag is de-
› for achieving maximum protection from the seat belts and the airbag system. ployed, you may suffer fatal injuries when adopting an incorrect seated posi-
tion!
WARNING
Note
■ Caution when adjusting the seat! You may suffer injuries or bruises as a re-
sult of adjusting the seat without paying proper attention. After a certain time, play can develop within the adjustment mechanism of the
■ The seat backrests must not be tilted too far back when driving, as this will backrest angle. 
impair the function of the seat belts and of the airbag system – risk of injury!
■ Never carry more people than the number of seats in the vehicle.
■ Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened » page 100, Transporting children safely with a
suitable restraint system.
■ The front seats and the head restraints must always be adjusted according
to height, so that the occupants can be protected as effectively as possible.
■ Do not carry any objects on the front passenger seat except objects de-
signed for this purpose (e.g. child seat) – risk of accident!

40 Using the system

 Adjusting the front seats Foldable front passenger seat

Fig. 36 Fig. 37
Control elements at the seat Folding the front passenger seat
forward

 First read and observe the introductory information and safety warn-
ings on page 40.  First read and observe the introductory information and safety warn-
ings on page 40.

Adjusting a seat in a forward/back direction The front passenger seat can be folded forward into a horizontal position.
› Pull the lever 1 » Fig. 36 up and push the seat into the desired position. Folding forward
› Release the lever 1 and push the seat until the lock clicks into place. › Place the lever in the direction of the arrow 1 » Fig. 37.
Adjusting height of seat › Fold the seat backrest forward in the direction of the arrow 2.
› To lift the seat, pull or pump the lever 2 » Fig. 36 upwards. The locking mechanism must audibly snap into place.
› To lower the seat, push or pump the lever 2 downwards.
The seat automatically moves forwards to the stop1).
Adjusting the angle of the seat backrest
› Remove the load on the seat backrest (do not lean on it), pull the lever Folding backward
3 » Fig. 36 or 4 1) towards the rear and set the desired angle of the seat back- › Place the lever in the direction of the arrow 1 » Fig. 37.
rest with the back. › Fold the seat backrest backward in the opposite direction of the arrow 2.
Folding the front seat forwards and moving it1) The locking mechanism must audibly snap into place.
› Pull the lever 3 » Fig. 36 or 4 and fold the seat backrest fully forwards. At the The seat automatically moves backwards to the stop1).
same time, move the seat forwards.
The seat automatically moves backwards into the preset position2). 
Moving seats into the initial position1)
› Move the seat towards the rear until the lock is heard to engage.
› Then push the seat backrest back into the upright position until the unlocking
button clicks into place - check by pulling on the seat backrest. 

1) Applies to front seats with the Easy Entry system.

2) Applies to front seats with the Easy Entry system and Memory function.

Seats and stowing 41

 With repeated pressing of the switch, the level of the seat heating is down-regu-
WARNING
lated up to the switch-off. The level of the seat heating is indicated by the num-
■ The front passenger airbag should be switched off when transporting ob- ber of illuminated warning lights in the switch.
jects on the seat backrest that has been folded forwards » page 99.
■ Only adjust the seat backrest when the vehicle is stationary. WARNING
■ When moving the seat backrest, make sure that the seat backrest has been
properly secured – check by pulling on the seat backrest. If, as an occupant, you have a subdued pain and/or temperature sensitivity,
■ When moving the seat backrest, keep limbs out of the area between the
e.g. through medication, paralysis or because of chronic illness (e.g. diabetes),
seat and seat backrest – risk of injury! we recommend you do not use seat heating on the driver or front passenger
■ The seat backrest that has been folded forwards must never be used to
seat. This can lead to burns on the back, the posterior and the legs which are
transport objects that: difficult to heal. If the seat heating is used, we recommend to make regular
■ impair driver visibility;
breaks in your journey when driving long distances, so that the body can recu-
■ can make it impossible for the driver to operate the vehicle, e.g. if they
perate from the stress of the journey. Please consult your doctor, who can
could fall under the pedals or protrude into the driver's area; evaluate your specific condition.
■ could injure passengers when the driver accelerates sharply, changes di-
rection or brakes.  CAUTION
■ Do not kneel on the seats or otherwise apply pressure at specific points to
avoid damaging the heating elements for the seat heaters.
Front seat heating ■ Do not use the seat heaters if the seats are not occupied by persons or if ob-
jects, such as a child seat, bag, etc., are fastened or stored on them. A fault of the
Fig. 38 heating elements in the seat heating can occur.
Heated front seats ■ Do not clean the seats using moisture » page 111, Seat covers.

Note
If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control » page 130,
Automatic load deactivation. 

Rear seats
 First read and observe the introductory information and safety warn-
ings on page 40.

The front seats can be heated electrically. In some seat versions, the seat back-  Introduction
rest is heated as well.
This chapter contains information on the following subjects:
The seat heating can only be switched on when the engine is running.
Folding the rear seats forward 43
› Press the symbol button  or  » Fig. 38. Head restraints 43 
Pressing once switches the seat heating on at its maximum level.

42 Using the system

 Folding the rear seats forward CAUTION
Ensure that the seat belts are not damaged when operating the seat backrests.
Fig. 39 Under no circumstances must the rear seat belts be jammed by the folded back
Unlock the seat backrest seat backrests. 

Head restraints

Fig. 40
Head restraints rear: adjusting/
removing

 First read and observe the introductory information given on page 42.

The rear seat backrest can be folded forwards to increase the size of the luggage
compartment.
Folding the seat backrest forwards
› Push the release handle A » Fig. 39 to unlock the seat backrest and fold it for-
ward.
› Move the head restraint fully towards the rear, or remove » page 43, Head re-
 First read and observe the introductory information given on page 42.

straints. Only the rear head restraints can be height-adjusted or removed or installed.
Folding the seat backrest back into position Setting height
› Push the head restraint into the slightly lifted seat backrest » page 43, Head › Grasp the side of the head restraint with both hands and push it upwards as re-
restraints. quired » Fig. 40.
› Then push the seat backrest back into the upright position until the unlocking › To move the head restraint downwards, press and hold the safety button 1
handle clicks into place - check by pulling on the seat backrest » . with one hand and press the head restraint downwards with the other hand.
› Make sure that the red marker B » Fig. 39 is hidden. Removing/installing
WARNING › Fold the seat backrest a little forward » page 43, Folding the rear seats forward.
› Grasp the side of the head restraint with both hands and push it upwards as re-
■ The belts and the belt locks must be in their original position after folding quired.
back the seat backrests – they must be ready to use. › Press the safety button 1 » Fig. 40 with one hand and keep it pressed down,
■ The seat backrests must be securely locked in position so that no objects in use the other hand to remove the head restraint.
the luggage compartment can slide into the passenger compartment on sud- › To reinstall, press the safety button 1 and keep it pressed while moving the
den braking – risk of injury. head rests as far down into the seat rests as possible until the safety button
■ Ensure that the rear seat backrests are properly engaged. It is only then that audibly latches. 
the three-point seat belt can reliably fulfil its function.

Seats and stowing 43

 Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured
WARNING
object with a weight of 4.5 kg produces an energy, which corresponds to 20 times
■ The head restraints must be correctly adjusted in order to offer effective its own weight. This means that it results in a weight of approx. 90 kg “ ”. You can
protection for the occupants in the event of an accident. imagine the injuries that can occur, if this “object” flies through the interior com-
■ Never drive with the head restraints removed - risk of injury. partment and hits an occupant.
■ If the rear seats are occupied, the rear head restraint must not be in the
Luggage compartment light
lower position.
The light switches on/off when the luggage compartment lid is opened or closed.

CAUTION WARNING
The head restraints are integrated into the seat backrests and cannot be adjus- ■ Store the objects in the luggage compartment and attach them to the lash-
ted.  ing eyes.
■ Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an accident and can injure the occupants or
Luggage compartment other oncoming traffic. This risk is still increased, if the objects which are fly-
ing around are hit by a deployed airbag. In this case, objects that are thrown
back may injure the occupants – risk to life.
 Introduction ■ Please note that transporting heavy objects alters the handling properties
of the vehicle due to the displacement of the centre of gravity – risk of acci-
This chapter contains information on the following subjects: dent! The speed and style of driving must be adjusted accordingly.
■ If the items of luggage or objects are attached to the lashing eyes with un-
Lashing eyes 45
Bag hooks 45 suitable or damaged lashing straps, injuries can occur in the event of braking
manoeuvres or accidents. To prevent items of luggage from being thrown for-
Fixing nets 46
ward, always use suitable lashing straps which must be firmly attached to the
Luggage compartment cover 46 lashing eyes.
Variable loading floor 47 ■ The transported items must be stowed in such a way that no objects are

Please observe the following for the purpose of maintaining good handling char- able to slip forward on sudden driving or braking manoeuvres – risk of injury!
■ When transporting fastened objects which are sharp and dangerous in the
acteristics of your vehicle:
luggage compartment that has been enlarged by folding the rear seats for-
› Distribute loads as evenly as possible. ward, ensure the safety of the passengers transported on the other rear
› Place heavy objects as far forward as possible. seats » page 89, Correct seated position for the passengers in the rear
› Attach the items of luggage to the lashing eyes or using the fixing seats.
net » page 45. ■ If the rear seat next to the folded forward seat is occupied, ensure maxi-
mum safety, e.g. by placing the goods to be transported in such a way that the
In the event of an accident, there is such a high kinetic energy which is produced
seat is prevented from folding back in case of a rear collision.
by small and light objects that they can cause severe injuries. The magnitude of
■ Never drive with the luggage compartment lid open or ajar, as otherwise ex-
the kinetic energy is dependent on the speed at which the vehicle is travelling
haust gases may get into the interior of the vehicle – risk of poisoning!
and the weight of the object. The speed at which the vehicle is travelling is in this
■ Under no circumstances should the permissible axle loads and the permissi-
case the more significant factor.
ble total vehicle weight be exceeded – risk of accident!
■ Never transport people in the luggage compartment! 

44 Using the system

 CAUTION Bag hooks
Please ensure that the heating elements for the rear window heater are not dam-
aged as a result of abrasive objects. Fig. 42
Luggage compartment: Bag
Note hooks

The tyre pressure must be adjusted to the load . 

Lashing eyes

Fig. 41
Luggage compartment: Lashing
eyes  First read and observe the introductory information and safety warn-
ings on page 44.

The luggage compartment has bag hooks used to secure smaller items of lug-
gage, e.g. bags, etc. » Fig. 42.

WARNING
Never use the bag hooks for lashing loaded goods. The bag hooks may tear
off during sudden braking manoeuvres or in the event of an accident.

 First read and observe the introductory information and safety warn-
ings on page 44.
CAUTION
Fixing eyes are located on the sides of the loading area for lashing the goods to
be loaded » Fig. 41. The bag hooks may be loaded up to a maximum of 1.5 kg. 

CAUTION
The maximum permissible load of the lashing eyes is 3.5 kN (350 kg). 

Seats and stowing 45

 Fixing nets CAUTION
Do not place any sharp objects in the nets – risk of net damage. 

Luggage compartment cover

Fig. 45
Removing/installing the luggage
compartment cover

Fig. 43 Fixing nets/fastening details in the rear area of the luggage com-
partment

 First read and observe the introductory information and safety warn-
ings on page 44.

The luggage compartment cover can be removed if you wish to transport bulky
goods.
Folding up/folding down
› To fold up, raise the luggage compartment cover and press into the side holders
1 » Fig. 45.
› To fold down, pull the raised part of the luggage compartment cover to the rear.
Fig. 44 Fixing nets: Details of the fastening behind the rear seats Removing/installing
› To remove, move the luggage compartment downwards from the side holders
 First read and observe the introductory information and safety warn-
ings on page 44.
2 » Fig. 45.
› To re-install it, place the luggage compartment cover on the side holders 2 and
press on them from above into the holders 2 .
Fixing examples for a fixing net as a horizontal pocket » Fig. 43 - .
Details of the fastening in the rear area of the luggage compartment » Fig. 43 - WARNING
.
■ No objects should be placed on the luggage compartment cover, the vehicle
Details of the fastening for the fixing net to the upper lashing eyes behind the occupants could be endangered if there is sudden braking or the vehicle col-
foldable rear seatrest » Fig. 44 - . lides with something.
■ Never drive while the luggage compartment cover is raised. Always fold it
Details of the fastening for the fixing net to the lashing eyes on the luggage com-
down before your journey, or remove it. 
partment floor behind the rear seats » Fig. 44 - .

46 Using the system

 Expanding luggage compartment downwards
CAUTION
› Lift the load floor and push into the grooves » Fig. 47 - .
Make sure that the luggage compartment cover is correctly engaged in the side › Place the load floor on the base of the luggage compartment.
holders 2 » Fig. 45 - risk of damage to luggage compartment cover/luggage
Expanding luggage compartment forwards
compartment. 
› Remove the luggage compartment cover » page 46.
› Remove the rear head restraints » page 43.
Variable loading floor › Fold the rear seat backrests forward » page 43. 

Roof rack system

 Introduction
This chapter contains information on the following subjects:
Attachment points for roof bars 48
Roof load 48

WARNING
Fig. 46 Variable loading floor: opening/folding up
■ The transported items on the roof rack must be securely attached – risk of
accident!
■ Always secure the load with appropriate and undamaged lashing straps or
tensioning straps.
■ Distribute the load evenly over the roof rack system.
■ Transporting heavy or large objects on the roof rack alters the handling
properties of the vehicle due to the displacement of the centre of gravity or
the increased wind exposure area – risk of accident! The style of driving and
speed must therefore be adapted to the current circumstances.
■ Avoid abrupt and sudden driving/braking manoeuvres.
■ Adjust the speed and driving style to the visibility, weather, road and traffic
conditions.
Fig. 47 Expanding luggage compartment: downwards/forwards ■ The permissible roof load, permissible axle loads and permissible total vehi-
cle weight must not be exceeded under any circumstances – risk of accident! 

 First read and observe the introductory information and safety warn-
ings on page 44.

Opening/closing
› Take the load floor at handle 1 and raise to the stop in the direction of the ar-
row » Fig. 46.
› Close the load floor against the direction of the arrow.

Seats and stowing 47

 CAUTION CAUTION
■ Only use roof rack systems approved by ŠKODA AUTO a.s. Observe the information regarding the assembly and disassembly in the enclosed
■ If other roof rack systems are used or if the roof bars are not fitted correctly, instructions. 
any resulting damage to the vehicle is not covered by the warranty. It is therefore
essential that the supplied fitting instructions for the roof rack system are ob-
served. Roof load
■ On vehicles with a panoramic sliding roof, make sure that the tilted panoramic
sliding roof not strike any items which are transported.
■ Ensure that the luggage compartment lid does not hit the roof load when
opened.
 First read and observe the introductory information and safety warn-
ings on page 47.

■ The height of the vehicle changes after mounting a roof luggage rack system The maximum permissible roof load (including roof rack system) of 50 kg and the
and the load that is secured to it. Compare the vehicle height with available clear- maximum permissible total weight of the vehicle should not be exceeded.
ances, such as underpasses and garage doors. The full permissible roof load cannot be used if a roof rack system with a lower
■ Always remove the roof luggage rack system before entering an automated car load carrying capacity is used. In this case, the roof rack system must only be loa-
wash. ded up to the maximum weight limit specified in the fitting instructions. 
■ Ensure the roof aerial is not impaired by the secured load.

For the sake of the environment Useful equipment

The increased aerodynamic drag results in a higher fuel consumption. 

 Introduction
Attachment points for roof bars This chapter contains information on the following subjects:
Cup holder 49
Ash tray 49
Cigarette lighter 50
12-volt power socket 50
Clothes hooks 51
Parking ticket holder 51 

Fig. 48 Attachment points

 First read and observe the introductory information and safety warn-
ings on page 47.

Perform the assembly and disassembly according to the enclosed instructions.

48 Using the system

 Cup holder Ash tray

Fig. 50
Front centre console: Ashtrays

Fig. 49 Centre console: Cup holder at the front/rear

 First read and observe the introductory information given on page 48.

 First read and observe the introductory information given on page 48.
Open/close
› To open, raise the cover of the ash tray in the direction of the arrow » Fig. 50.
The cup holder is located in the front » Fig. 49 -  and rear » Fig. 49 -  of the › To close, press the cover of the ash tray fully downwards.
centre console.
Removing
Fixing cups in the front cup holder › Pull out the ashtray upwards » .
Fold the cup holder clip » Fig. 49 -  towards the front.
Install
Place the cup into the cup holder so that the cup holder clip surrounds the cup › Insert the ashtray vertically.
securely.
WARNING
WARNING
Never place flammable objects in the ashtray – risk of fire!
■ Never put hot beverage containers in the cup holder. If the vehicle moves,
they may spill – risk of scalding!
■ Do not use any cups or beakers which are made of brittle material (e.g. glass, CAUTION
porcelain). This could lead to injuries in the event of an accident. When removing, do not hold the ashtray at the cover – risk of breakage. 

CAUTION
Do not leave open beverage containers in the cup holder during the journey.
There is a risk of spilling e.g. when braking which may cause damage to the elec-
trical components or seat upholstery. 

Seats and stowing 49

 Cigarette lighter 12-volt power socket

Fig. 51 Fig. 52
Centre console: Cigarette lighter Centre console: Power socket

 First read and observe the introductory information given on page 48.
 First read and observe the introductory information given on page 48.

Operating the cigarette lighter The 12-Volt power socket is located in the front centre console » Fig. 52.
› Press in the button of the cigarette lighter » Fig. 51. Using the power socket
› Wait until the button pops forward. › Open the power socket cap » Fig. 52.
› Remove the cigarette lighter immediately and use. › Connect the plug for the electrical appliance to the socket.
› Place the cigarette lighter back into the socket.
WARNING WARNING

Take care when using the cigarette lighter! Improper use of the cigarette
■ Improper use of the 12-volt power socket and the electrical accessories can
lighter can cause burns. cause fires, burns and other serious injuries.
■ Never leave children unattended in the vehicle. The power socket and the
connected devices can only be used when the ignition is switched on.
Note ■ If the connected electric device becomes too hot, switch it off and discon-
nect it from the power supply immediately.
■ The cigarette lighter operates only if the ignition is switched on.
■ The cigarette lighter socket can also be used as a 12Volt socket for electrical ap-
pliances » page 50, 12-volt power socket. CAUTION
■ Further information » page 112, Modifications, repairs and technical altera-
tions. 
■ The 12-Volt power socket will only work when ignition is switched on.
■ The 12-volt power socket can only be used for connecting approved electrical
accessories with a total power uptake of up to 120 watt.
■ Never exceed the maximum power consumption, otherwise the vehicle's elec-
trical system can be damaged.
■ If electrical consumers are switched on when the engine is not running, this will
cause the car battery to discharge – risk of battery discharge!
■ Only use matching plugs to avoid damaging the power socket.
■ Only use accessories that have been tested for electromagnetic compatibility in
accordance with the applicable directives. 

50 Using the system

■ Before turning the ignition on or off, and before starting the car, switch off the
device connected to the 12-volt power socket to prevent any damage caused by
voltage fluctuations.
 First read and observe the introductory information given on page 48.

■ Observe the operating instructions for the connected devices!  The note holder » Fig. 53 is designed e.g. for attaching car park tickets.

WARNING
Clothes hooks
The attached note has to always be removed before starting off in order not
to restrict the driver's vision.


First read and observe the introductory information given on page 48.

The clothes hooks are located at the centre door bars.

Storage compartments
WARNING
■ Ensure that any clothes hanging from the hooks do not impair your vision to
 Introduction
the rear. This chapter contains information on the following subjects:
■ Only use the hooks for hanging light items of clothing and ensure that there
are no heavy or sharp-edged objects in the pockets. Storage compartment on the driver's side 52
■ Do not use clothes hangers for hanging up items of clothing otherwise this Storage compartment on the front passenger side 52
may reduce the effectiveness of side airbag. storage Storage compartment with lid on the front passenger side 52
Bag holder 53
CAUTION Photo holder 53
Storage compartment in the front centre console 53
The maximum permissible load of the hooks is 2 kg. 
Multimedia holder 54
Meshed pockets on the front seat rests 54
Storage compartments in front of the rear seats 54
Parking ticket holder
WARNING
Fig. 53
Windscreen: Parking ticket hold- ■ Do not place anything on the dash panel. These objects might slide or fall
er down when driving and may distract you from concentrating on the traffic –
risk of accident!
■ When driving, ensure that no objects from the centre console or from other
storage compartments can get into the driver's footwell. You would then no
longer be able to apply the brakes or operate the clutch or accelerator pedal –
risk of accident! 

Seats and stowing 51

 Storage compartment on the driver's side  First read and observe the introductory information and safety warn-
ings on page 51.

Fig. 54 The open stowage compartment can be found underneath the dash panel on the
Dash panel: Storage compart- driver's side » Fig. 55.
ment on the driver's side Bag hooks
There is a bag hook 1 » Fig. 55 at the open stowage compartment which is used
to hang smaller items of luggage, e.g. bags, or similar.

CAUTION
The maximum permissible load of the hook is 1.5 kg. 

 First read and observe the introductory information and safety warn-
ings on page 51. storage Storage compartment with lid on the front passenger
side
The open stowage compartment can be found underneath the dash panel on the
driver's side » Fig. 54.

WARNING
■ Ensure that when driving no objects from the centre console may get into
the driver's footwell. You would then no longer be able to apply the brakes or
operate the clutch or accelerator pedal – risk of accident!
■ Never store hard, heavy or sharp items in an opened stowage compartment. 

Storage compartment on the front passenger side

Fig. 56 Dash panel: Storage compartment on the front passenger side

Fig. 55
Dash panel: Storage compart-
ment on the front passenger
 First read and observe the introductory information and safety warn-
ings on page 51.

side Open/close
› Pull on the opening lever 1 » Fig. 56.
Please read the following information if there is a foldable hook in the opening
lever » page 53, in section Bag holder.
› To close, push the cover upwards.
The cover must engage firmly. 

52 Using the system

Overview of the stowage compartment:
Photo holder
1 Opening lever
2 Glasses storage box
3 Notepad holder
Fig. 58
Dash panel: Photo holder
4 Pen holder
5 Coin holder
6 Card holder

WARNING
The storage compartment must always be closed when driving for safety rea-
sons. 

Bag holder
 First read and observe the introductory information and safety warn-
ings on page 51.

The middle part of the dashboard has a holder » Fig. 58 which is used to fasten
e.g. photos, notes, etc.
Fig. 57
Dash panel: folding hooks CAUTION
Do not damage the holders when handling them. 

Storage compartment in the front centre console

Fig. 59
Front centre console: Stowage
 First read and observe the introductory information and safety warn-
ings on page 51.
compartment

There is a foldable hook in the opening lever of the storage compartment on the
front passenger's side » Fig. 57 which is used to suspend smaller items of lug-
gage, e.g. bags, etc.

CAUTION
■ The maximum permissible load of the hook is 1.5 kg.
■ When the hook is folded forward, it folds back automatically when the storage
compartment is opened.
 First read and observe the introductory information and safety warn-
ings on page 51.

■ We recommend detaching suspended luggage from the hook before the stor- The open stowage compartment in the centre console » Fig. 59. 

age compartment lid is opened. 

Seats and stowing 53

 Multimedia holder  First read and observe the introductory information and safety warn-
ings on page 51.

Fig. 60 The insides of the front seat rests have meshed pockets » Fig. 61.
Front centre console: Multimedia These meshed pockets are designed for small, light objects, such as a mobile
holder phone or MP3 player.

WARNING
You can use the meshed pockets to store items with a gross weight of up to
150 g. Heavy objects are not secured sufficiently – risk of injury!

CAUTION
 First read and observe the introductory information and safety warn-
ings on page 51. Never put large objects, such as bottles, or objects with sharp edges in the mesh-
ed pockets - risk of damaging the meshed pockets. 
The multimedia holder can be found in the stowage compartment of the front
centre console » Fig. 60.
You can use this holder to store e.g. a mobile phone, MP3 player or similar devi- Storage compartments in front of the rear seats
ces.
Fig. 62
WARNING In front of the rear seats: Stow-
Never use the multimedia holder as an ashtray or for storing flammable ob- age compartment
jects – risk of fire! 

Meshed pockets on the front seat rests

 First read and observe the introductory information and safety warn-
ings on page 51.

There are open stowage compartments located in front of the rear seats » Fig. 62. 

Fig. 61 Front seat rests: Meshed pockets

54 Using the system

 Note
Heating and air-conditioning
■ The used air streams out through the vents in the luggage compartment.
■ We recommend that you do not smoke in the vehicle when the recirculating air
Heating, ventilation, cooling mode is operating since the smoke which is drawn at the evaporator from the in-
terior of the vehicle forms deposits in the evaporator of the air conditioning sys-
tem. This produces a permanent odour when the air conditioning system is oper-
 Introduction
ating which can only be eliminated through considerable effort and expense (re-
This chapter contains information on the following subjects: placement of compressor). 

Air outlet vents 55

Using the air conditioning system economically 56 Air outlet vents
Operational problems 56
The heating effect is dependent upon the coolant temperature, thus full heat
output only occurs when the engine has reached its operating temperature.
If the cooling system is switched on, the temperature and air humidity drops in
the vehicle. The cooling system prevents the windows from misting up during
winter months.
It is possible to briefly activate recirculated air mode to enhance the cooling ef-
fect.
Please refer to the information regarding the recalculated air mode for air-condi-
tioning » page 59.
Fig. 63 Air outlet vents
WARNING
For your own safety and that of other road users, ensure that all the windows
are free of ice, snow and misting. Please familiarize yourself about how to cor-
 First read and observe the introductory information and safety warn-
ings on page 55.

Warmed, unwarmed or cooled air will flow out of the air outlet vents according to
rectly operate the heating and ventilation systems, how to demist and defrost
the setting of the regulator of the heating or the air conditioning system and the
the windows, as well as with the cooling mode.
atmospheric conditions.
Opening
CAUTION
› To open the air outlet vents 1 » Fig. 63 press on the air outlet vent.
■ The air inlet in front of the windscreen must be free of ice, snow or leaves to
Closing
ensure that the heating and cooling system operates properly.
■ After switching on the cooling Condensation from the evaporator of the air con-
› To close the air outlet vents 1 » Fig. 63fold the fins back.
ditioning may drip down and form a puddle below the vehicle. This is quite normal Changing the air flow direction
and not an indication of a leak! › Adjust the flow direction by turning the fins. 

Heating and air-conditioning 55

 Note Heating
Do not cover the air outlet vents with objects of any kind. 

 Introduction
Using the air conditioning system economically This chapter contains information on the following subjects:
Control elements 56
 First read and observe the introductory information and safety warn-
ings on page 55. Setting heating 57 

The compressor on the air conditioning system uses power from the engine when
in cooling mode which will effect the fuel consumption. Control elements
It recommended to open the windows or the doors of a vehicle for which the inte-
rior has been strongly heated through the effect of direct sunlight in order to al-
low the heated air to escape.
The cooling system should not be switched on while travelling when the window
is open.
If the desired interior temperature can also be achieved without activating the
cooling system, fresh air mode should be selected.

For the sake of the environment

Pollutant emissions are also reduced when fuel is saved » page 71. 

Operational problems
Fig. 64 Heating: Control elements

 First read and observe the introductory information and safety warn-
ings on page 55.
 First read and observe the introductory information given on page 56.

If the cooling system does not operate at outside temperatures higher than +5 °C,
there is a problem in the system. The reasons for this may be. Setting temperature
› One of the fuses has blown. Check the fuse and replace if necessa- › Turn the control dial A » Fig. 64 to the right to increase the temperature.
ry » page 148. › Turn the control dial A to the left to decrease the temperature.
› The cooling system has switched off automatically for a short time because the Controlling blower
coolant temperature of the engine is too hot » page 13. › Turn the blower switch B » Fig. 64 into one of the positions 1-4 to switch the
If you are not able to resolve the operational problem yourself, or if the cooler blower on.
output has reduced, switch off the cooling system and seek assistance from a › Turn the blower switch B into position 0 to switch the blower off.
specialist garage. 
Regulating the air distribution
› The direction of the inlet air flow is controlled with air distribution regulator
C » Fig. 64 » page 55, Air outlet vents. 

56 Using the system

All controls apart from the blower switch B can be set to any desired intermedi-
Note
ate position.
The blower should always be on to prevent the windows from misting up. If the air distribution is positioned towards the windows, the total amount of air is
used to defrost the windows and thus no air will be fed to the footwell. This can
lead to restriction of the heating comfort. 

Setting heating

 First read and observe the introductory information given on page 56.

Recommended basic settings of the heating controls for the respective operating modes:
Setting the regulator » Fig. 64 on page 56
Set-up Air outlet vents 1 » Fig. 63 on page 55
A B C

Defrosting the windscreen and side windows To the right up to the stop 3
 Open and align with the side window

Free windscreen and side windows from mist Desired temperature 2 or 3  Open and align with the side window

The fastest heating To the right up to the stop 3

 Opening

Comfortable heating Desired temperature 2 or 3  Opening

Fresh air mode – ventilation To the left up to the stop Desired position
 Opening


The cooling system only operates if the following conditions are met.
Air conditioning system  AC E » Fig. 65 on page 58 switched on.
 The engine is running.
 Introduction  The outside temperature is above approx. +2 °C.
 The blower switch is switched on (positions 1-4).
This chapter contains information on the following subjects:
Under certain circumstances, air at a temperature of about 5 °C can flow out of
Control elements 58
the vents when the cooling system is switched on. Lengthy and uneven distribu-
Setting the air conditioning system 59
tion of the air flow out of the vents and large differences in temperature between
Recirculated air mode 59 inside and outside, for example when getting out of the vehicle, can result in
chills in sensitive persons. 

Heating and air-conditioning 57

 The warning light in the button lights up.
Note
We recommend that you have the air conditioning system cleaned by a specialist
› Press the AC button.
garage once every year.  The warning light in the button goes out.

Note
Control elements ■ If the air distribution is positioned towards the windows, the total amount of air
is used to defrost the windows and thus no air will be fed to the footwell. This
can lead to restriction of the heating comfort.
■ The warning light in the AC E » Fig. 65 button lights after activation, even if
not all of the conditions for the function of the cooling system have been met.
Therefore, when all conditions are met, it is signalised that the cooling system is
ready for operation. 

Fig. 65 The air conditioning system: Control elements

 First read and observe the introductory information given on page 57.

Setting temperature
› Turn the control dial A » Fig. 65 to the right to increase the temperature.
› Turn the control dial A to the left to decrease the temperature.
Controlling blower
› Turn the blower switch B » Fig. 65 into one of the positions 1-4 to switch the
blower on.
› Turn the blower switch B into position 0 to switch the blower off.
› To close the fresh air supply, move the sliding regulator D into the position
 » page 59, in section Recirculated air mode.
Regulating the air distribution
› The direction of the inlet air flow is controlled with air distribution regulator
C » Fig. 65.

Switching the cooling system on/off

› Press the AC button E » Fig. 65.

58 Using the system

 Setting the air conditioning system

 First read and observe the introductory information given on page 57.

Recommended basic settings of the control elements of the air conditioning system for the respective operating modes:
Button » Fig. 65 on
Setting the regulator » Fig. 65 on page 58 Air outlet vents 1 » Fig. 63
Set-up page 58
on page 55
A B C D E
Defrost/defog windscreen and Desired tempera- Open and align with the side
side windowsa) ture
3 or 4
  Activated
window

To the right up to Brief ,

The fastest heating
the stop
3
 then 
Switched off Opening

Desired tempera-
Comfortable heating
ture
2 or 3   Switched off Opening

To the left up to briefly 4, then Brief ,

The fastest cooling
the stop 2 or 3  then 
Activated Opening

Desired tempera-
Comfortable cooling
ture
1, 2 or 3
  Activated Open and align to the roof

To the left up to
Fresh air mode – ventilation
the stop
Desired position
  Switched off Opening

a) We recommend that you do not use this setting in countries with high humidity levels. This can result in heavy cooling of the window glass and the following fogging from outside. 

Switching off
Recirculated air mode › Move the sliding regulator D » Fig. 65 on page 58 into position .

 First read and observe the introductory information given on page 57.
WARNING
Do not leave recirculated air mode on over a longer period of time, as “stale”
Recirculated air mode prevents polluted air outside the vehicle from getting into
air can cause fatigue of the driver and passengers, reduce attention levels and
the vehicle, for example when driving through a tunnel or when standing in a
also cause the windows to mist up. The risk of having an accident increases.
traffic jam.
Switch off recirculated air mode as soon as the windows start to mist up. 
Switching on
› Move the sliding regulator D » Fig. 65 on page 58 into position .

Heating and air-conditioning 59

 WARNING (Continued)
Communication and multimedia ■ If a mobile phone or a two-way radio system is operated in a vehicle without
an external aerial or an external aerial which has been installed incorrectly,
Telephone and Move & Fun this can increase the strength of the electromagnetic field inside the vehicle.
■ Two-way radio systems, mobile phones or mounts must not be installed on
airbag covers or within the immediate deployment range of the airbags.
 Introduction ■ Never leave a mobile phone on a seat, on the dash panel or in another area
from which it can be thrown during a sudden braking manoeuvre, an accident
This chapter contains information on the following subjects:
or a collision — risk of injury.
Mobile phones and two-way radio systems 60 ■ For air transport, the Bluetooth® function of the hands-free system must be
Multifunction deviceMove & Fun 61  switched off by a ŠKODA service partner!

Note
Mobile phones and two-way radio systems
■ We recommend that the installation of mobile phones and two-way radio sys-

 First read and observe the introductory information given on page 60. tems in a vehicle be carried out by a ŠKODA Partner.
■ The range of the Bluetooth® connection to the hands-free system is restricted
to the vehicle interior. The range is dependent on local factors, e.g. obstacles be-
ŠKODA permits the operation of mobile phones and two-way radio systems with
tween the devices and mutual interferences with other devices. If your mobile
a professionally installed external aerial and a maximum transmission power of
phone is in a jacket pocket, for example, this can lead to difficulties when estab-
up to 10 watts.
lishing a connection with the hands-free-system or transferring data. 
Please consult a ŠKODA Partner for information about the possibility of installing
and operating mobile phones and two-way radio systems with a transmission
power of more than 10 W.
Operating mobile phones or two-way radio systems may interfere with the func-
tionality of the electronic systems in your vehicle.
The reasons for this are as follows:
› no external aerial;
› external aerial incorrectly installed;
› transmission power greater than 10 watts.
WARNING
■ Concentrate fully at all times on your driving! As the driver you are fully re-
sponsible for the operation of your vehicle. Use the telephone system only to
such an extent that you are in full control of your vehicle at any time.
■ The national regulations for using a mobile phone in a vehicle must be ob-
served.

60 Using the system

 Setting the tilt of the multifunction device
Multifunction deviceMove & Fun › You can set the tilt to the required position by moving the multifunction device
in the direction of the arrows » Fig. 67 » .
Fig. 66
Removing the multifunction device
Cap of the opening for the cradle
of the multifunction device
› With one hand, secure the multifunction device on the upper and lower edge.
› Using the other hand, press the release button C » Fig. 67 and remove the de-
vice.
› Store the multifunction device in a safe place to avoid damaging it.
Removing the cradle on the multifunction device
› Grab hold of the cradle with one hand.
› With the other hand, press the release button A » Fig. 67.
› Remove the cradle from the dash panel from above.
› Seal the opening for the cradle in the dash panel with the cover » Fig. 66.
Loading the user manual
› Switch on the multifunction device by pressing button D » Fig. 67.
› Press the button more on the screen.
› Press the button Manual on the screen.
› Call up the required chapter by pressing the appropriate button.
Functions of the multifunction device
› Navigation.
› Operating the radio using multimedia devices connected via Bluetooth®.
› Displaying information from the MFD, rev counter and coolant tempera-
Fig. 67 Cradle on the multifunction device/multifunction device ture » page 8.
› Hands-free device for mobile phones coupled with the multifunction device via
Bluetooth®.
 First read and observe the introductory information given on page 60.
› Indicator for opened bonnet, doors and luggage compartment lid.
› Display from the visual parking system (OPS).
Removing the cap › Image viewer.
› Insert a slotted screwdriver into the recess marked with an arrow » Fig. 66 and
fold the cover carefully upwards. WARNING
Installing the cradle for the navigation unit ■ Concentrate fully at all times on your driving! As the driver you are fully re-
› Place the cradle into the opening of the centre section of the dash panel from sponsible for the operation of your vehicle. Only use the system such that you
above, press it down until it latches » . are in full control of your vehicle in every traffic situation – risk of accident!
■ The multifunction device must always slot securely into the cradle or be
Installing the multifunctional device
safely stored in the vehicle.
› Firstly, place the multifunction device into the top holder B » Fig. 67 and press 
it on the underside of the cradle until it latches » .

Communication and multimedia 61

 WARNING (Continued)
■ Unsecured or incorrectly secured multifunction devices may be thrown
through the interior of the vehicle and cause injuries in a sudden driving or
braking manoeuvre or accident.
■ Adjust the volume to ensure that acoustic signals from outside, e.g. sirens
from vehicles which have the right of way, such as police, ambulance and fire
brigade vehicles, can be heard at all time.
■ High volumes can cause hearing damage.

CAUTION
■ Improper tilt settings can damage both the multifunction device and the cradle.
■ Always take the multifunction device with you when leaving the vehicle to pro-
tect it from extreme temperatures and strong sunlight. Extreme ambient temper-
atures can impair the functioning of the multifunction device and may damage
the device.
■ Moisture can damage the electrical contacts in the dash panel for the portable
multifunction device.
■ Never use water when cleaning the navigation unit cradle. Always use a dry
cloth instead.
■ Install/remove the multifunction device cradle without the multifunction device
in it.
■ Do not install/remove the multifunction device until the cradle for the multi-
function device has been installed into the dash panel.

Note
The range of the Bluetooth® connection to the hands-free system is restricted to
the vehicle interior. The range is dependent on local factors, e.g. obstacles be-
tween the devices and mutual interferences with other devices. If your mobile
phone is e.g. in a jacket pocket, this can lead to difficulties when establishing the
Bluetooth® connection with the hands-free system or the data transfer. 

62 Using the system

 WARNING (Continued)
Driving ■ When driving, the ignition key must always be in the position 2 » Fig. 69 on
page 65 (ignition switched on) without the engine running. This position is
indicated by the warning lights coming on. If this is not the case, this could re-
Starting-off and Driving sult in unexpected locking of the steering wheel – risk of accident!
■ Only pull the ignition key from the ignition lock when the vehicle has come
to a complete stop (by applying the handbrake). Otherwise, the steering could
Starting and stopping the engine be blocked – risk of accident!
■ When leaving the vehicle, the ignition must always be removed. This is par-
 Introduction ticularly important if children are left in the vehicle. Children could otherwise
start the engine for example – risk of accident or injury!
This chapter contains information on the following subjects: ■ Never leave the engine running in unventilated or closed rooms. The ex-

Adjusting the steering wheel position 64 haust gases from the engine contain substances such as odourless and col-
ourless carbon monoxide (a poisonous gas) – risk to life! Carbon monoxide can
Electromechanical power steering 64
cause unconsciousness and death.
Electronic immobiliser 64 ■ Never leave the vehicle unattended with the engine running.
Ignition lock 65 ■ Never switch off the engine before the vehicle is stationary – risk of acci-
Starting the engine 65 dent!
Switching off the engine 65 ■ After switching off the ignition, the radiator fan can intermittently continue
to operate for approx. 10 minutes.
WARNING
■ Never adjust the steering wheel when the vehicle is moving only when the CAUTION
vehicle is stationary!
■ Adjust the steering wheel so that the distance B » Fig. 68 on page 64
■ The starter may only be operated when the engine is not running. The starter or
between the steering wheel and your chest is at least 25 cm. Not maintaining engine can be damaged if the starter is activated when the engine is running.
■ Let go of the ignition key as soon as the engine starts otherwise the starter
this minimum distance will mean that the airbag system will not be able to
properly protect you – risk to life! could be damaged.
■ Avoid high engine revolutions, full throttle and high engine loads before the en-
■ The lever for adjusting the steering wheel must be locked whilst driving so
that the position of the steering wheel cannot accidentally change during the gine has reached its operating temperature – risk of damaging the engine!
■ Do not tow-start the engine – risk of damaging the engine! On vehicles with a
journey – risk of accident!
■ If the steering wheel is adjusted further towards the head, the protection catalytic converter, unburnt fuel may get into the catalytic converter where it may
provided by the driver airbag in the event of an accident is reduced. Check ignite. This in turn may damage the catalytic converter. The battery from another
that the steering wheel is aligned to the chest. vehicle can be used as a jump-start aid » page 144, Jump-starting.
■ Do not switch the engine off immediately at the end of your journey after the
■ When driving, hold the steering wheel with both hands firmly on the outer
edge in the 9 o'clock and 3 o'clock position. Never hold the steering wheel in engine has been operated over a prolonged period at high loads but leave it to
the 12 o'clock position or in any other way (e.g. in the middle or inner edge of run at an idling speed for about 1 minute. This prevents any possible accumulation
the steering wheel). Otherwise, activation of the driver airbag could cause se- of heat when the engine is switched off. 
vere injuries to arms, hands and head.

Starting-off and Driving 63

 For the sake of the environment › Pull the lever A » Fig. 68 below the steering wheel down.
› Adjust the height of the steering wheel to the desired position.
Do not warm up the engine while the vehicle is stationary. If possible, start your › Push the lever upwards to the stop. 

journey as soon as the engine has started. Through this the engine reaches its
operating temperature more rapidly and the pollutant emissions are lower.
Electromechanical power steering
Note
■ The engine can only be started with the correctly coded original key.
■ The engine running noises may louder at first be louder for a short time after
 First read and observe the introductory information and safety warn-
ings on page 63.

starting the cold engine. This is quite normal and is not an operating problem. The power steering enables you to steer the vehicle with less physical force.
■ After switching off the ignition, the radiator fan can intermittently continue to With the electromechanical power steering, the steering assist is automatically
operate for approx. 10 minutes. adapted to the speed and to the steering angle.
■ If the engine does not start up after a second attempt, the fuse for the fuel
pump may have a fault. Check the fuse and replace if necessary » page 148, It is still possible to fully steer the vehicle if the power steering fails or if the en-
Fuses on the underside of the dash panel, or seek assistance from a specialist ga- gine is not running (vehicle being towed in). However, greater physical effort is
rage. required to turn the steering wheel.
■ We recommend locking the steering wheel whenever leaving the vehicle. This If there is a fault in the power steering, the warning light  or  lights up in the
acts as a deterrent against the attempted theft of your car. 
instrument cluster » page 16.

WARNING
Adjusting the steering wheel position
Contact a specialist garage if the power steering is faulty. 

Electronic immobiliser

 First read and observe the introductory information and safety warn-
ings on page 63.

An electronic chip is integrated in the head of the key. The immobiliser is deacti-
vated with the aid of this chip when the key is inserted in the ignition lock. The
electronic immobiliser is automatically activated when the ignition key is with-
drawn from the lock.
Fig. 68 Adjustable steering wheel: Lever below the steering wheel/safe dis-
tance to the steering wheel The engine will not start if a non-authorized ignition key is used. 

 First read and observe the introductory information and safety warn-
ings on page 63.

The height of the steering wheel can be adjusted.

› First of all adjust the driver's seat » page 41.

64 Driving
 If the engine does not start within 10 seconds, abort the start-up process and
Ignition lock turn the key to position 1 . Repeat the start-up process after approx. half a mi-
nute.
Fig. 69 Release the handbrake before starting off. 
Positions of the vehicle key in
the ignition lock
Switching off the engine

 First read and observe the introductory information and safety warn-
ings on page 63.

Switch off the engine by turning the ignition key into position 1 » Fig. 69 on
page 65. 

 First read and observe the introductory information and safety warn-
ings on page 63.

1 Ignition switched off, engine off, the steering can be locked

Braking
2 Ignition switched on
3 Starting engine  Introduction
To lock the steering, with the ignition key withdrawn, turn the steering wheel This chapter contains information on the following subjects:
until the steering locking pin engages audibly.
Information on braking 66
If the steering is locked and the key cannot or can only be turned with difficulty Handbrake 66
into the position 2 » Fig. 69, move the steering wheel back and forth and the
steering lock will unlock. 
WARNING
■ Greater physical effort is required for braking when the engine is switched
Starting the engine off – risk of accident!
■ The clutch pedal must be actuated when braking on a vehicle with manual

 First read and observe the introductory information and safety warn-
ings on page 63.
transmission, when the vehicle is in gear and at low revs. Otherwise, the func-
tion of the brake booster may be impaired – risk of accident!
■ If a front spoiler, full wheel trim, etc. is mounted retrospectively, it must be
Before starting the engine, place the gearshift lever into neutral or place the se- ensured that the air supply to the front wheel brakes is not reduced. The front
lector lever in the position N and firmly put on the handbrake. brakes may overheat, which can have a negative impact on the functioning of
Fully depress and hold the clutch pedal, switch on the ignition 2 » Fig. 69 on the braking system – risk of accident!
page 65 and start 3 – do not operate the accelerator. Depress the clutch pedal ■ Please note that the handbrake must be fully released. A handbrake which
until the engine starts. is only partially released can cause the rear brakes to overheat, which can
have a negative impact on the functioning of the braking system – risk of acci-
Let go of the key as soon as the engine starts. After letting go, the vehicle key dent!
will return to position 2 . ■ Never leave children unattended in the vehicle. The children might, for ex-
ample, release the handbrake or take the vehicle out of gear. The vehicle
could then start to move – risk of accident! 

Starting-off and Driving 65

 Corrosion
CAUTION
Corrosion on the brake discs and dirt on the bake pads occur if the vehicle has
■ Observe the recommendations on the new brake pads » page 71. been parked for a long period and if you do not make much use of the braking
■ Never let the brakes slip with light pressure on the pedal if braking is not neces- system. If the brake system is not used much or if there is corrosion on the sur-
sary. This causes the brakes to overheat and can also result in a longer braking face, we recommend cleaning the brake discs by firmly applying the brakes from a
distance and excessive wear. high speed.
Faults in the brake surface
Note If it is found that the braking distance has suddenly become longer and that the
■ If the brakes are applied in full and the control unit for the braking system con- brake pedal can be depressed further, the brake system may be faulty. Visit a
siders the situation to be dangerous for the following traffic, the brake light specialist garage immediately and adjust your style of driving appropriately as you
flashes automatically. After the speed was reduced below around 10 km/h or the will not know the exact extent of the damage.
vehicle was stopped, the brake light stops flashing and the hazard warning light Low brake fluid level
system switches on. The hazard warning light system is switched off automatical- An insufficient level of brake fluid may result in problems in the brake system. The
ly after accelerating or driving off again. level of the brake fluid is monitored electronically » page 14, Braking system.
■ Before negotiating a steep downhill section, reduce the speed, shift down into
the next lower gear (manual gearbox) or select a lower drive position (automatic Brake booster
gearbox). As a result, the braking effect of the engine will be used, reducing the The brake booster increases the pressure generated with the brake pedal. The
load on the brakes. Any additional braking should be completed intermittently, brake booster only operates when the engine is running. 

not continuously. 

Handbrake
Information on braking
Fig. 70
 First read and observe the introductory information and safety warn-
ings on page 65.
Centre console: Handbrake

Wear-and-tear
The wear of the brake pads is dependent on the operating conditions and driving
style. The brake pads wear more quickly if a lot of journeys are completed in
towns and over short distances or if a very sporty style of driving is adopted. Un-
der these severe conditions, the thickness of the brake pads must be checked by
a specialist garage before the next service appointment.
Wet roads or road salt
The performance of the brakes can be delayed as the brake discs and brake pads
may be moist or have a coating of ice or layer of salt on them in winter. The
 First read and observe the introductory information and safety warn-
ings on page 65.

brakes are cleaned and dried by applying the brakes several times. Apply
› Pull the handbrake lever firmly upwards.
Loosening
› Pull the handbrake lever up slightly and at the same time push in the locking
button » Fig. 70.
› Move the lever right down while pressing the lock button. 

66 Driving
The handbrake warning light  lights up when the handbrake is applied, provided The reversing lights will come on once reverse gear is engaged, provided the igni-
the ignition is on. tion is on.
A warning signal sounds if the vehicle is inadvertently driven off with the hand-
brake applied. WARNING
The handbrake warning is activated if the vehicle is driven at a speed of more Never engage reverse gear when driving – risk of accident!
than 6 km/h for more than 3 seconds. 

Note
Manual gear changing and pedals If not in the process of changing gear, do not leave your hand on the gearshift
lever while driving. The pressure from the hand can cause the gearshift mecha-
nism to wear excessively. 
 Introduction
This chapter contains information on the following subjects: Pedals
Manual gear changing 67
Pedals 67 
 First read and observe the introductory information given on page 67.

The operation of the pedals must not be hindered under any circumstances!
Manual gear changing
In the driver's footwell, only a footmat, which is attached to the two correspond-
ing attachment points, may be used.
Fig. 71
Shift pattern of the 5-speed Only use footmats from the range of ŠKODA Original Accessories, which are fitted
manual gearbox to two attachment points.

WARNING
No objects are allowed in the driver's footwell – risk of obstruction or limita-
tion in operating the pedals! 

 First read and observe the introductory information given on page 67. Automatic gearbox
Always depress the clutch pedal fully when changing gear, to prevent excessive  Introduction
wear of the clutch.
The gearshift indicator must be observed when changing gear » page 10. This chapter contains information on the following subjects:

Only engage reverse gear when the vehicle is stationary. Depress the clutch pedal Introductory information 68
and hold it fully depressed. Wait a moment before reverse gear is engaged to Starting-off and driving 68
avoid any shift noises. Selector lever positions 69
Manual gearshift (Tiptronic) 69 

Starting-off and Driving 67

Kickdown function 70 If the selector lever position N is accidentally selected while driving, it is first nec-
Operational faults 70 essary to release pressure on the accelerator pedal and wait for the idling speed
of the engine to be reached before the selector lever can be engaged in the drive
WARNING position.

■ Do not depress the accelerator if changing the position of the selector lever Note
when the vehicle is stationary and the engine is running – risk of accident!
■ Never move the selector lever into position R or when driving - risk of an ac- If the N symbol flashes next to the selector lever, engage the selector lever posi-
cident! tion N. 
■ The selector lever must be placed into position N and the handbrake firmly
applied before the bonnet can be opened and work on the running engine can
be completed - risk of accident! The safety guidelines must always be ob- Starting-off and driving
served » page 120, Engine compartment.
■ If stopping on a hill (downhill gradient), never try to maintain the vehicle sta-
tionary with the gear engaged by means of the “accelerator pedal”, i.e. by let-
ting the clutch slip. This can lead to overheating of the clutch, and subse-
 First read and observe the introductory information and safety warn-
ings on page 67.

quently to the clutch burning out. The vehicle can roll backward - risk of acci- Starting off
dent! › Firmly depress and hold the brake pedal.
■ If you have to stop on a slope, depress and hold the brake pedal to prevent › Press the selector lever towards the left in the spring-tensioned position in the
the vehicle from rolling back. direction of the arrow » Fig. 72 on page 69 and insert into position D.
■ On a smooth or slippery road surface using the kickdown function can cause › Release the brake pedal and accelerate.
the driven wheels to spin – risk of skidding! Stop
■ Always firmly apply the handbrake before leaving the vehicle!
› The selector lever position N does not have to be selected when stopping for a
short time, such as at a cross roads. It is sufficient to hold the vehicle stationary
CAUTION using the foot brake. The engine can, however, be allowed just to idle.

■When the vehicle is stationery and the engine running, the brake pedal must be Parking
used to stop the vehicle in al selector settings.  › Depress the brake pedal.
› Firmly apply the handbrake.
› Move the selector lever to the right in the direction of the arrow » Fig. 72 on
Introductory information page 69 into position N. 

 First read and observe the introductory information and safety warn-
ings on page 67.

Shifting up and down through the gears is performed automatically. However, the
gearbox can also be switched into Tiptronic mode M. This mode makes it possible
for you to also shift gears manually » page 69.
The engine can only be left on in position N, when the brake pedal is depressed .
When parking, the handbrake must be securely applied before position N is selec-
ted.

68 Driving
 M - Manual gearshift (Tiptronic)
Selector lever positions Further information » page 69. 

Fig. 72
Selector lever Manual gearshift (Tiptronic)

 First read and observe the introductory information and safety warn-
ings on page 67.

N – Neutral
The transmission is in Neutral in this position. Fig. 73 Selector lever: manual shifting/instrument cluster: engaged gear

The brake pedal must be depressed to move the selector lever out of the posi-
tion N into position D or R when the vehicle is stationary and the ignition is
switched on.
 First read and observe the introductory information and safety warn-
ings on page 67.

Tiptronic mode makes it possible to manually shift gears on the selector lever.
R – Reverse gear
Reverse gear must only be engaged when the vehicle is stationary and the en- The gearshift indicator must be observed when changing gear » page 10.
gine is idling.
Switching to manual shifting when the vehicle is stationary
The brake pedal must be depressed before setting into position R from position › Depress the brake pedal.
N. › Press the selector lever twice to the left in the spring-tensioned position.
When the ignition is switched on and the selector lever is in position R, the re- Switching to manual shifting during driving
verse lights will come on. › Press the selector lever towards the left in the spring-tensioned position in the
direction of the arrow and insert into position M. The selector lever position you
D – Position for driving forward (normal programme)
have engaged appears in the display of the instrument cluster 1 » Fig. 73.
When the selector lever is in this position, the forward gears are automatically
shifted up and down in line with the engine load, accelerator pedal actuation and Shifting up gears
driving speed. › Press the selector lever fowards » Fig. 73 + .
The brake pedal must be depressed before setting into position D from position Shifting down gears
N. › Press the selector lever backwards » Fig. 73 - .
Under certain circumstances (e.g. when driving in mountainous regions) it may be When accelerating, the gearbox automatically shifts up into the higher gear just
beneficial to select the manual shift programme » page 69 for a short time in before the maximum permissible engine speed is reached.
order to adapt the gearbox ratios manually to the driving situations.
If a lower gear is selected, the gearbox does not shift down until there is no risk
of the engine overrevving. 

Starting-off and Driving 69

If you operate the kickdown function, the gearbox shifts into a lower gear in line
Note
with the vehicle speed and engine speed.
If the automatic gearbox is faulty, seek help from a specialist garage as soon as
Note possible and have the fault fixed. 

The kickdown function is also available when manually shifting gears. 

Running in
Kickdown function
 Introduction
 First read and observe the introductory information and safety warn-
ings on page 67. This chapter contains information on the following subjects:
The kickdown function provides you with maximum acceleration power. New engine 70
New tyres 71
When the accelerator pedal is fully depressed, the kickdown function is activated
in the desired driving program. This function has precedence over the driving pro- New brake pads 71 
gramme and serves for maximum acceleration of the vehicle when exploiting the
maximum power potential of the engine without taking into account the current
selector lever position (D or Tiptronic M). The gearbox shifts down to one or sev- New engine
eral gears in line with the driving state and the vehicle accelerates. The gearbox
does not shift up into the highest gear until the engine has reached its maximum
revolutions for this gear range.   First read and observe the introductory information given on page 70.

The engine has to be run in during the first 1 500 kilometres.

Operational faults Up to 1 000 kilometres

› Do not drive faster than 3/4 of the maximum speed of the gear in use, i.e. 3/4 of
 First read and observe the introductory information and safety warn-
ings on page 67.
the maximum permissible engine speed.
› No full throttle.
› Avoid high engine speeds.
Faults in the automatic gearbox › Do not tow a trailer.
In the event of a fault in the automatic gearbox, warning lights may light up in the
instrument panel » page 18,     Automated transmission. From 1 000 up to 1 500 kilometres
Gradually increase the power output of the engine up to the full speed of the
In some instances, the gear may run in emergency mode. In this case, the vehicle gear engaged, i.e. up to the maximum permissible engine speed.
can only be driven at reduced speed.
During the first operating hours the engine has higher internal friction than later
The vehicle does not start off after engaging the selector lever position until all of the moving parts have harmonized. The driving style which you adopt
If the vehicle does not start off, the problem may be that the selector lever is not during the first approx.1 500 kilometres plays a decisive part in the success of
completely in the selected position. In such an instance, press the brake pedal running in your car.
and put the selector lever into the required position.
Never drive at unnecessarily high engine speeds even after the running-in period
is complete. The maximum permissible engine speed is marked by the start of the
red scale area of the revolutions counter. 

70 Driving
On vehicles fitted with a manual gearbox, at the very latest shift up into the next
gear when the red area is reached. Very high engine speeds when accelerating Economical driving and environmental sustainability
(accelerator) are automatically restricted » .
With vehicles with a manual gearbox, do not drive at unnecessarily low engine  Introduction
speeds. Shift down a gear when the engine is no longer running smoothly. Ob-
serve the recommended gear » page 10, Recommended gear. This chapter contains information on the following subjects:
Looking ahead 72
CAUTION Energy-efficient gear switching 72
Avoiding full throttle 72
■ The engine is not protected from excessive engine revs caused by shifting
down at the wrong time. This can result in a sudden increase in revs beyond the Reducing idling 72
permissible maximum rpm, thereby causing engine damage. Regular maintenance 73
■ Never rev up a cold engine when the vehicle is stationary or when driving in in- Avoid short distances 73
dividual gears. Checking tyre inflation pressures 73
■ All the speed and engine revolution figures apply only when the engine is at its Avoid unnecessary ballast 74
normal operating temperature. Saving electricity 74
Environmental compatibility 74
For the sake of the environment
The technical requirements for low fuel usage and economic efficiency of the ve-
Do not drive at unnecessarily high engine speeds. Shifting up sooner helps save hicle have already been built into the vehicle at the works. ŠKODA places a partic-
fuel, reduces engine noise and protects the environment. 
ular emphasis on minimising negative effects on the environment.
It is necessary to take note of the guidelines given in this chapter in order to
New tyres make best use of these characteristics and to maintain their effectiveness.
Fuel consumption, environmental pollution and the wear to the engine, brakes

 First read and observe the introductory information given on page 70. and tyres depend essentially on the following three factors:
› your personal driving style
› operating conditions
New tyres must firstly be “run in” since they do not offer optimal grip at first.
Therefore, drive especially carefully for the first 500 km or so.  › technical requirements
The fuel economy by can be improved by 10 -15 % by always looking ahead and
driving in an economical way.
New brake pads Fuel consumption is also be influenced by external factors which are beyond the
driver's control. Consumption increases during the winter or under difficult condi-
 First read and observe the introductory information given on page 70.
tions, on poor roads, etc.
Fuel consumption can vary considerably from the manufacturer's data, as a result
New brake pads do not initially provide optimal braking performance. They first of outside temperatures, the weather and driving style.
need to be “run in”. Therefore, drive especially carefully for the first 200 km or so. 
The optimal engine speed should be obtained when accelerating, in order to
avoid a high fuel consumption and resonance of the vehicle. 

Starting-off and Driving 71

 Looking ahead Avoiding full throttle

 First read and observe the introductory information given on page 71.
Fig. 75
Principle sketch: Fuel consump-
A vehicle's highest fuel consumption occurs when accelerating, therefore unnec- tion in litres/100 km. and speed
essary accelerating and braking should be avoided. If looking ahead when driving, in km/h.
less braking and consequently less accelerating are required.
If possible, let your vehicle coast to a stop, or use the engine brake, if you can see
that the next set of traffic lights is on red, for example. 

Energy-efficient gear switching

Fig. 74
 First read and observe the introductory information given on page 71.

Principle sketch: Fuel consump- Driving more slowly saves fuel.

tion in litres/100 km depending Sensitive use of the accelerator will not only significantly reduce fuel consump-
on the selected gear tion but also positively influence environmental pollution and wear of your vehi-
cle.
The maximum speed of your vehicle should, as far possible, never be used. Fuel
consumption, pollutant emissions and vehicle noises increase disproportionally at
high speeds.
The » Fig. 75 shows the ratio of fuel consumption to the speed of your vehicle.

 First read and observe the introductory information given on page 71. Fuel consumption will be halved if you drive at only three-quarters of the possible
top speed of your vehicle. 

Shifting up early saves on fuel.

Manual gearbox Reducing idling
› Drive no more than about one length of your vehicle in first gear.
› Shift up into the next gear at approx. 2 000 revolutions.
An effective way of achieving good fuel economy is to shift up early. Observe the
 First read and observe the introductory information given on page 71.

recommended gear » page 10, Recommended gear. Idling also costs fuel.
A suitably selected gear can have an effect on fuel consumption » Fig. 74. In vehicles not equipped with the START-STOP system, turn off the engine when
in a traffic jam, at a level crossing or traffic lights with longer wait times.
Automatic gearbox
› Slowly apply the accelerator pedal. However, do not depress it to the kickdown Even after just 30 – 40 seconds you will have saved more fuel than that is needed
position. when you start the engine up again. 
› An economic driving programme is automatically selected if the accelerator ped-
al is only depressed slowly. 

72 Driving
If an engine is only idling it takes much longer for it to reach its normal operating
temperature. Wear-and-tear and pollutant emissions, though, are particularly
Avoid short distances
high in the warming-up phase. Therefore, start driving as soon as the engine has
started, whereby high engine speeds should be avoided. 
Fig. 76
Principle sketch: Fuel consump-
tion in l/100 km at different tem-
Regular maintenance peratures

 First read and observe the introductory information given on page 71.

A poorly tuned engine uses an unnecessarily high amount of fuel.

By having your vehicle regularly maintained by a specialist garage, you create the
conditions needed for economical driving. The maintenance state of your vehicle
has a positive effect on traffic safety and value retention
A poorly tuned engine can result in a fuel consumption which is 10 % higher than
 First read and observe the introductory information given on page 71.

Short distances result in an above-average high fuel consumption. We therefore

normal. recommend avoiding distances of less than 4 km if the engine is cold.
Also check the oil level when refuelling. Oil consumption is dependent to a con-
A cold engine consumes the most fuel immediately after the start. Fuel consump-
siderable extent on the load and speed of the engine. Oil consumption could be
tion drops to 10 litres/100 km after just 1 kilometre. The consumption stabilises
as high as 0.5 litres/1 000 km depending on your style of driving.
once the engine and catalytic converter have reached their operating tempera-
It is quite normal that a new engine has a higher oil consumption at first, and rea- ture.
ches its lowest level only after a certain running in time. The oil consumption of a
An important factor in this connection is also the ambient temperature. The im-
new vehicle can therefore only be correctly assessed after driving about
age » Fig. 76 shows the different levels of fuel consumption after driving a certain
5 000 km.
distance at a temperature of +20 °C and a temperature of -10 °C.

For the sake of the environment Your vehicle has a higher fuel consumption in winter than in summer. 

■ Additional improvements to the fuel economy can be made by using synthetic

high-lubricity oils. Checking tyre inflation pressures
■ Regularly check the ground under the vehicle. Have your vehicle inspected by a
specialist garage if you find any stains caused by oil or other fluids on the ground.

Note
 First read and observe the introductory information given on page 71.

Tyres which are correctly inflated save fuel.

We recommend that your vehicle be serviced on a regular basis by a ŠKODA serv- Always ensure the tyre inflation pressure is correct. If the inflation pressure is too
ice partner. 
low, the tyres will have to overcome a higher rolling resistance. This will not only
increase fuel consumption but also tyre wear and the driving behaviour will wor-
sen.
Always check the tyre inflation pressure when the tyres are cold. 

Starting-off and Driving 73

 Design measures
Avoid unnecessary ballast › Joints designed to be easily detached.
› Simplified disassembly due to the modular structure system.
 First read and observe the introductory information given on page 71.
› Improved purity of different classes of materials.
› Identification of all plastic parts in accordance with VDA Recommendation 260.
Transporting ballast costs fuel. › Reduced fuel consumption and exhaust emission CO2.
Each kilogramme of weight increases the fuel consumption. It is worth checking
› Minimum fuel leakage during accidents.
the luggage compartment to avoid transporting any unnecessary ballast.
› Reduced noise.
Choice of materials
It is particularly in town traffic, when one is accelerating quite often, that the ve-
hicle weight will have a significant effect upon the fuel consumption. A rule of
› Extensive use of recyclable material.
thumb here is that an increase in weight of 100 kilograms will cause an increase
› Air conditioning filled with CFC-free refrigerant.
in fuel consumption of about 1 litre/100 kilometres.
› No cadmium.
› No asbestos.
At a speed of 100 - 120 km/h, your vehicle that is fitted with a roof rack cross › Reduction in the “vaporisation” of plastics.
member without a load will use about 10 % more fuel than normal due to the in-
creased aerodynamic drag.  Manufacture
› Solvent-free cavity protection.
› Solvent-free protection of the vehicle for transportation from the production
Saving electricity plant to the customer.
› The use of solvent-free adhesives.
› No CFCs used in the production process.
 First read and observe the introductory information given on page 71.
› Without use of mercury.
› Use of water-soluble paints.
When the engine is running, the alternator generates and supplies electrical pow-
er. If more electrical components of the electrical system are switched on, more Trade-in and recycling of old cars
fuel is needed to operate the alternator. We therefore recommend switching off ŠKODA meets the requirements of the brand and its products with regard to pro-
electrical components if these are no longer required.  tecting the environment and the preserving resources. All new ŠKODA vehicles
can be utilized up to 95 % and always1) be returned. In a lot of countries sufficient
trade-in networks have been created, where you can trade-in your vehicle. After
Environmental compatibility you trade-in your vehicle, you will receive a confirmation stating the recycling in
accordance with environmental regulations.

 First read and observe the introductory information given on page 71.
Note
Environmental protection has played a major role in the design, material selection You can find more detailed information about the trade-in and recycling of old
and production of your new ŠKODA. Particular emphasis has been placed on the cars from a specialist garage. 

following points.

1) Subject to fulfilment of the national legal requirements.

74 Driving
 › Determine the depth of the water before driving through.
Avoiding damage to your vehicle
The water level must not reach above the bar on the lower beam » Fig. 77.

 Introduction › Do not drive any faster than at a walking speed.

At a higher speed, a water wave can form in front of the vehicle, which can cause
This chapter contains information on the following subjects: water to penetrate into the engine's air induction system or other parts of the ve-
General information 75 hicle.
Driving through water on streets 75  › Never stop in the water, do not reverse and do not switch the engine off.
› Deactivate the START-STOP system before driving through water » page 82,
Function.
General information
WARNING
 First read and observe the introductory information given on page 75.
■ Driving through water, mud, sludge etc. can impair the braking power and
extend the braking distance – risk of accident!
Pay attention to low-slung parts of the vehicle, such as the spoiler and exhaust, ■ Avoid abrupt and sudden braking immediately after water crossings.
particularly in the following situations. ■ After driving through bodies of water, the brakes must be cleaned and dried
› When driving on poorly maintained roads and paths. as soon as possible by intermittent braking. Only apply the brakes for the pur-
› When driving over kerbs. pose of drying and cleaning the brake discs if the traffic conditions permit this.
› When driving on steep ramps, etc. Do not place any other road users in jeopardy.
Particular attention is required for vehicles with sport suspension and when the
vehicle is fully laden. 
CAUTION
■ When driving through water, some parts of the vehicle such as the engine,
Driving through water on streets gearbox, chassis or electrics can be severely damaged.
■ Oncoming vehicles can generate water waves which can exceed the permissible
water level for your vehicle.
Fig. 77
■ Potholes, mud or rocks can be hidden under the water making it difficult or im-
Driving through water
possible to drive through the body of water.
■ Do not drive through salt water. The salt can lead to corrosion. Any vehicle parts
that have come into contact with salt water must be rinsed immediately with
fresh water.

Note
After driving through water, we recommend having the vehicle checked by a spe-
cialist garage. 

 First read and observe the introductory information given on page 75.

The following instructions must be observed if vehicle damage is to be avoided

when driving through water (e.g. flooded roads).

Starting-off and Driving 75

 Driving abroad

 Introduction
This chapter contains information on the following subjects:
Unleaded petrol 76
Headlights 76
In certain countries, it may be possible that the ŠKODA Partner network is limited
or has not been established. This is the reason why procuring certain spare parts
may be somewhat complicated and specialist garages may only be able to make
limited repairs. 

Unleaded petrol

 First read and observe the introductory information given on page 76.

A vehicle fitted with a petrol engine must always be refuelled with unleaded pet-
rol » page 116, Unleaded petrol. Information regarding the locations of filling sta-
tions that offer unleaded petrol is, for example, provided by the automobile asso-
ciations. 

Headlights

 First read and observe the introductory information given on page 76.

The low beam of your headlights is set asymmetrically. It illuminates the side of
the road on which the vehicle is being driven to a greater extent.
When driving in countries in which the traffic drives on the other side of the road
than in your home country, the asymmetrical low beam may dazzle oncoming
drivers. In order to avoid this, the headlights must be adjusted at a specialist ga-
rage.

Note
You can find out more information on adjusting the headlights at a specialist ga-
rage. 

76 Driving
 Electronic Stability Control (ESC)
Assist systems

Brake assist systems  First read and observe the introductory information and safety warn-
ings on page 77.

The ESC system helps improve control of the vehicle in situations where it is be-
 Introduction ing operated at its dynamic limits, such as a sudden change to the direction of
travel. The risk of skidding is reduced and your car thus offers greater driving sta-
This chapter contains information on the following subjects: bility depending on the conditions of the road surface.
Electronic Stability Control (ESC) 77 The ESC system is automatically activated each time the ignition is switched on.
Antilock Braking System (ABS) 78 The direction which the driver wishes to take is determined based on the steering
Traction Control System (TCS) 78 angle and the speed of the vehicle and is constantly compared with the actual
Electronic Differential Lock (EDL) 78 behaviour of the vehicle. In the event of deviations, such as the car beginning to
skid, the ESC system will automatically brake the appropriate wheel.
WARNING During an intervention of the system, the warning light  flashes in the instru-
■ A lack of fuel can cause irregular engine running or cause the engine to shut ment cluster.
down. The brake assist systems would then fail to function – risk of accident! The following systems are integrated into the electronic stabilisation control
■ Adjust the speed and driving style to the current visibility, weather, road and (ESC):
traffic conditions. The increased safety provided by the brake assist systems › Antilock brake system (ABS),
must not tempt you to take safety risks – risk of accident! › Traction control (TCS);
■ In the event of an ABS fault, visit a specialist garage immediately. Adjust
› Electronic Differential Lock (EDL)
your style of driving according to the damage to the ABS, as you will not know › Hydraulic Brake Assist (HBA)
the exact extent of the damage or the extent to which this is limiting the › Hill Hold Control (HHC).
braking efficiency.
In the event of an ESC fault, the ESC warning light  illuminates in the instru-
ment cluster » page 16.
CAUTION
Hydraulic Brake Assist (HBA)
■ All four wheels must be fitted with the same tyres approved by the manufactur- The HBA is activated by very quick operation of the brake pedal. HBA increases
er to ensure the brake assist systems operate correctly. the braking effect and helps to shorten the braking distance. In order to achieve
■ Changes to the vehicle (e.g. to the engine, brakes, chassis or another combina- the shortest possible braking distance, the brake pedal must be applied firmly un-
tion of tyres and wheels) can influence the functionality of the brake assist sys- til the vehicle has come to a standstill.
tems » page 112, Modifications, repairs and technical alterations.
The ABS is activated faster and more effectively with the intervention of the HBA.

Note The HBA function is automatically switched off when the brake pedal is released.

If a fault occurs in the ABS system, the ESC, ASR and EDL will also fail to work. An Hill Hold Control (HHC)
ABS fault is indicated with the warning light  » page 17.  When driving on slopes, HHC allows you to move your foot from the brake pedal
to the accelerator pedal without having to use the handbrake.
The system holds the brake pressure produced by the activation of the brake
pedal for approx. 2 seconds after the brake pedal is released. 

Assist systems 77
The brake pressure drops gradually the more you operate the accelerator pedal. If
the vehicle does not start off within 2 seconds, it starts to roll back.
Electronic Differential Lock (EDL)
The HHC is active on slopes of 5% and steeper, provided that the driver's door is
closed. HHC is always only active on slopes when in forward or reverse start off.
When driving downhill, it is inactive. 
 First read and observe the introductory information and safety warn-
ings on page 77.

If one of the wheels starts to spin, the EDL system brakes the spinning wheel and
transfers the driving force to the other wheels. This ensures the stability of the
Antilock Braking System (ABS) vehicle and a quick journey.
In the event of severe stresses, the EDL switches off automatically in order to
 First read and observe the introductory information and safety warn-
ings on page 77.
avoid excessive heat generation in the disc brake of the wheel being braked. The
vehicle can continue to be driven and has the same characteristics as a vehicle
not fitted with EDL. The EDL switches on again automatically as soon as the
ABS prevents the wheels locking when braking. Thus helping the driver to main-
brake has cooled down. 
tain control of the vehicle.
The intervention of the ABS is noticeable from the pulsating movements of the
brake pedal which is accompanied by noises.
Parking aid
When the ABS system is active, do not brake periodically or reduce the pressure
on the brake pedal. 
 Introduction
This chapter contains information on the following subjects:
Traction Control System (TCS)
Function 79

 First read and observe the introductory information and safety warn-
ings on page 77.
Visual parking system

WARNING
79

If the wheels are slipping, the TCS adapts the engine speed to the conditions of
the road surface. The TCS makes it much easier to start off, accelerate and climb ■ The parking aid is not a substitute for the driver paying proper attention and
steep hills even if the conditions of the road surface are unfavourable. it is always the driver's responsibility to take care when reversing the vehicle
or carrying out similar manoeuvres. Pay particular attention to small children
The TCS function is automatically activated each time the ignition is switched on.
and animals as they are not recognised by the parking aid sensors.
During an intervention of the system, the warning light  flashes in the instru- ■ Before reversing, you should make sure that there are no small obstacles,
ment cluster. such as rocks, thin posts, trailer drawbars etc. in front or behind your vehicle.
Such obstacles may not be recognised by the parking aid sensors.
If there is a fault in the TCS, the warning light then lights up in the instrument
■ Under certain circumstances, surfaces of certain objects and types of cloth-
cluster  » page 17. 
ing cannot reflect the signals from the parking aid. Thus, these objects or peo-
ple who wear such clothing are not recognised by the parking aid sensors.
■ External sound sources can have a detrimental effect on the parking aid.
Under unfavourable conditions, objects or people may not be recognised. 

78 Driving
 Activating/deactivating the parking aid
CAUTION
The parking aid is activated automatically when reverse gear is engaged and the
■ If a warning signal sounds for about 3 seconds after activating the system and ignition is turned on. This is confirmed by a brief audible signal.
there is no obstacle close to your car, this indicates a system fault. Have the fault The parking aid is deactivated by removing the reverse gear. 
rectified by a specialist garage.
■ The sensors must be kept clean (free of ice, etc.) to enable the parking aid to
operate properly. Visual parking system
Note
Fig. 79
■ Additionally installed modules such as bicycle carriers can impair the function of Screen display of the visual
the parking aid.  parking system

Function

Fig. 78
Parking aid: Range of sensors

 First read and observe the introductory information and safety warn-
ings on page 78.

The visual parking system is shown in the screen of the multifunctional device
Move & Fun.
Switching on the screen display of the visual parking system
When the ignition and the multifunction device Move & Fun are both on, the visu-

 First read and observe the introductory information and safety warn-
ings on page 78.
al parking system is switched on by shifting into reverse gear.
A An obstacle appearing in the collision zone is shown as an orange-coloured
The parking aid determines the distance between the rear bumper and an obsta- segment » Fig. 79. Do not drive the vehicle!
cle with the aid of ultrasound sensors. The sensors are integrated in the rear B An area without detected obstacles is shown as a transparent segment.
bumper. C An obstacle in the sensor range which lies outside of the collision area is
shown by the light-blue segment.
Range of sensors
D A region behind the detected obstacle is shown with the dark-blue segment.
The clearance warning begins at a distance of about 150 cm from the obstacle
(area A » Fig. 78). The interval between the warning signals becomes shorter as Switching off the screen display of the visual parking system
the clearance is reduced.
The screen display can be switched off as follows.
A continuous tone sounds from a distance of approx. 30 cm (area B ) – danger › By tapping the symbol button  on the multifunction device screen » Fig. 79.
area. You should not reverse any further after this signal sounds! › By shifting out of reverse.
On the Move & Fun multifunction device, the distance to the obstacle can be › By turning off the ignition. 
shown graphically.

Assist systems 79
 WARNING WARNING
Concentrate fully at all times on your driving! As the driver you are fully re- ■ For safety reasons, the cruise control system must not be used in dense
sponsible for the operation of your vehicle. Only use the system so that you traffic or on unfavourable road surfaces (such as icy roads, slippery roads,
are in full control of your vehicle in every traffic situation - risk of accident! loose gravel) – risk of accident!
■ The saved speed may only be resumed if it is not too high for the current
traffic conditions.
Note ■ Always deactivate the cruise control system after use to prevent the system
■ The visual parking system is shown in the screen of the multifunction device being switched on unintentionally.
Move & Fun within a few seconds of shifting into reverse gear.
■ More information about the mobile multifunction device Move & Fun can be
CAUTION
found in the digital operating manual in the device » page 61, Multifunction de-
viceMove & Fun.  ■ The cruise control system is not able to maintain a constant speed when driving
in areas with steeper gradients. The weight of the vehicle increases the speed at
which it travels. Therefore, shift to a lower gear in good time or slow the vehicle
Cruise Control System down by applying the foot brake.
■ It is not possible to switch on the cruise control system on vehicles fitted with a
manual gearbox if the first gear or reverse gear is engaged.
 Introduction ■ It is not possible on vehicles fitted with an automatic gearbox to switch on the
cruise control system if the selector lever is in the position N or R.
This chapter contains information on the following subjects: ■ The Cruise Control System may automatically switch off when some assist sys-

Storing a speed 81 tems (e.g. ESC, City Safe Drive) intervene, when the speed exceeds maximum per-
Changing a stored speed 81 missible engine speed, or if a similar event takes place. 

Switching off the cruise control system temporarily 81

Switching off the cruise control system completely 81
The Cruise Control System (CCS) maintains a set speed, more than 25 km/h, with-
out you having to actuate the accelerator pedal.
This is only possible within the range which is permitted by the power output and
braking power of the engine.
The warning light  illuminates in the instrument cluster when the cruise control
system is activated.

80 Driving
 Decreasing the speed
Storing a speed › The stored speed can be reduced by pressing the rocker button B » Fig. 80 on
page 81 into the position SET.
Fig. 80 › The speed will decrease continuously, if the rocker button is pressed and held in
Operating lever: Operating the the SET position. Release the rocker button once the desired speed is reached.
cruise control system The set speed is then stored in the memory.
› If the rocker button is released at a speed of less than 30 km/h, the speed is not
stored and the memory is erased. The speed must then be stored again by
pressing the rocker button B in the position SET after increasing the speed of
the vehicle to more than 30 km/h.
The speed can also be reduced by depressing the brake pedal, which temporarily
deactivates the system. 

 First read and observe the introductory information and safety warn-
ings on page 80. Switching off the cruise control system temporarily
Storing a speed
› Turn the switch A » Fig. 80 into the ON position.
› After the desired speed has been reached, press the rocker button B into the
 First read and observe the introductory information and safety warn-
ings on page 80.
SET position. The cruise control system is temporarily switched off by pushing the switch
A » Fig. 80 on page 81 into the spring-mounted position CANCEL or by depress-
After you have released the rocker button B out of the position SET, the speed
ing the brake or clutch pedal.
you have just stored is maintained at a constant speed without having to depress
the accelerator.  The set speed remains stored in the memory.
Briefly press the rocker button B into the position RES to resume the stored
speed after the clutch or brake pedal is released. 
Changing a stored speed

 First read and observe the introductory information and safety warn-
ings on page 80. Switching off the cruise control system completely

Increasing the speed with the accelerator

› Depress the accelerator to increase the speed.
› Release the accelerator to reduce the speed back down to the preset speed.
 First read and observe the introductory information and safety warn-
ings on page 80.

› Turn the switch A » Fig. 80 on page 81 » page 81 into the OFF position. 
However, if the saved speed is exceeded by more than 10 km/h for a period of
more than 5 minutes by depressing the accelerator, the stored speed is deleted
from the memory. You have to re-store the desired speed.
Increasing the speed with the rocker button B
› Press the rocker button B » Fig. 80 on page 81 into the RES position.
› The speed will increase continuously, if the rocker button is pressed and held in
the RES position. Release the rocker button once the desired speed is reached.
The set speed is then stored in the memory.

Assist systems 81
 START/STOP  First read and observe the introductory information and safety warn-
ings on page 82.

 Introduction The START-STOP system helps you to save fuel while at the same time reducing
harmful exhaust emissions and CO2 emissions.
This chapter contains information on the following subjects: The function is automatically activated each time the ignition is switched on.
Function 82 In the start-stop mode, the engine automatically switches to the vehicle's idle
phase, e.g. when stopped at traffic lights. The engine restarts automatically
WARNING where necessary.
■ The brake servo unit and power steering only operate if the engine is run- Information regarding the current state of the START-STOP system is indicated in
ning. the display of the instrument cluster.
■ Never let the vehicle roll with the engine switched off.
Automatic engine shut down (stop phase)
› Stop the vehicle (where necessary, apply the handbrake).
CAUTION › Take the vehicle out of gear.
› Release the clutch pedal.
Always deactivate the START-STOP system when driving through wa-
ter » page 75. Automatic renewed engine restart (start phase).
› Depress the clutch pedal.
Note Switching the START-STOP system on and off
Changes to the outdoor temperature can have an effect on the internal tempera- The START/STOP system can be switched on/off by pressing the button » Fig. 81.
ture of the vehicle battery even after several hours. If the vehicle remains out- When start-stop mode is deactivated, the warning light in the button lights up.
doors for a long time in minus temperatures or in direct sunlight, it can take sev-
If the vehicle is in the stop phase when manually switching off the system, the
eral hours until the internal temperature of the vehicle battery reaches a suitable
engine starts immediately.
temperature for proper operation of the START STOP system. 

The START-STOP system is very complex. Some of the procedures are hard to
check without servicing. The general conditions for the proper functioning of the
Function START-STOP system are listed in the following overview.
Conditions that must be completely met for automatic engine switch-off (stop
Fig. 81 phase)
Button for the START-STOP sys- › The gearshift lever is in Neutral.
tem › The clutch pedal is not depressed.
› The driver has fastened the seat belt.
› The driver's door is closed.
› The bonnet is closed.
› The vehicle is at a standstill.
› The engine is at operating temperature.
› The charge state of the vehicle battery is sufficient.
› The stationary vehicle is not on a steep slope or a steep downhill section.
› The engine speed is less than 1 200 rpm. 

82 Driving
› The temperature of the vehicle battery is not too low or too high.
› There is sufficient pressure in the braking system. City Safe Drive
› The difference between the outdoor- and the set temperature in the interior is
not too great.  Introduction
› The vehicle speed since the last time the engine was switched off was greater
than 3 km/h.
› The front wheels are not turned excessively (the steering angle is less than 3/4
of a steering wheel revolution).
The automatic re-start (start phase) takes place in each of the following
interventions:
› The clutch is depressed.
› The max./min. temperature is set.
› The defrost function for the windscreen is switched on.
› A high blower stage has been selected.
› The START STOP button is pressed.
The automatic re-start takes place in each of the following situations, without Fig. 82 Laser sensor/detection range
intervention from the driver:
› The vehicle moves at a speed of more than 3 km/h. This chapter contains information on the following subjects:
› The difference between the outdoor- and the set temperature in the interior is Switching the City Safe Drive on and off 84
too great. Laser sensor 85
› The charge state of the vehicle battery is not sufficient. Special driving situations 85
› There is insufficient pressure in the braking system.
The City Safe Drive system uses the laser sensor » Fig. 82 –  to take readings
If the driver's seat belt is removed for more than 30 seconds during stop mode or
about the traffic situation in front of the vehicle at a range of around 10 metres (11
the driver's door opened, the engine must be started manually using the key. 
yards) » Fig. 82 –  in a vehicle speed range of 5 - -30 km/h (3 - -19 mph).
If the driver does not respond to an imminent collision, the City Safe Drive system
can automatically apply the brakes to the vehicle to prevent a possible collision.
If the City Safe Drive system is currently slowing the vehicle down automatically,
the warning light will flash  quickly.
Automatic braking interventions can be terminated by pressing the clutch, accel-
erator or by moving the steering wheel.
If the City Safe Drive system is not currently available, or if there is a system fault,
the warning light will flash  slowly.
The following conditions cause the City Safe Drive system to become not availa-
ble.
› Taking bends tightly.
› When fully pressing down the accelerator pedal.
› When the City Safe Drive system function is switched off/faulty.
› When the laser sensor is dirty, concealed or has overheated » page 85. 

Assist systems 83
› In the event of snow, heavy rain or fog. Note
› When vehicles are travelling side by side.
› When vehicles are crossing. ■ When replacing the windscreen wiper blades, only use windscreen wiper blades
› When vehicles are approaching in the same lane. approved by the manufacturer.
› When the vehicles are very dirty and have a low level of reflection. ■ Do not paint the laser sensor range on the windscreen. Do not cover it up with
› With high levels of dust. stickers or similar.
■ Remove any snow with a hand-held brush and we recommend you remove any
WARNING ice with a solvent-free deicing spray.
■ Keep the laser sensor range free of dirt and ice at all times.
■ The City Safe Drive system cannot exceed physical and system-defined lim- ■ If the laser sensor range on the windscreen has scratches, cracks, etc, replace
its. The added convenience of the City Safe Drive system must never give you the windscreen. Only use windscreens approved by the manufacturer. Carrying
a reason to takes risks with regard safety. The driver is always the one re- out repairs to the windscreen are not permissible.
sponsible for braking in time. ■ A damaged windscreen in the area of the laser sensor can lead to a failure of
■ The City Safe Drive system cannot prevent accidents and injuries by itself.
the City Safe Drive system.
■ The City Safe Drive system can carry out unexpected braking interventions ■ Repairing the laser sensor requires specialist expertise. We recommend the
in complex driving situations, e.g. when vehicles scrape past each other. ŠKODA service partners. 
■ Taking the City Safe Drive system into account in one's own driving behav-
iour can lead to accidents and serious injuries. The City Safe Drive system is
not a substitute for the driver's attention. Switching the City Safe Drive on and off
■ Always adapt your speed and safety distance to the vehicle ahead to the
visibility, weather, road and traffic conditions.
■ The laser beam from the laser sensor can cause serious eye injuries. Fig. 83
■ Never use optical devices, e.g. a range-finder camera or magnifying glass to Lower part of the centre con-
look into the laser sensor. sole: Button for the City Safe
■ The laser beam can also be active when the City Safe Drive system is Drive system
switched off or is not available. The laser beam is not visible to the human
eye.
■ The City Safe Drive system cannot detect persons, animals, or crossing vehi-
cles or approaching vehicles in the same lane.
■ The City Safe Drive system cannot exceed physical and system-defined lim-
its. For instance, responses from the City Save Drive system can happen late
or unexpectedly from the driver's perspective. Always stay attentive and take
control when required.  First read and observe the introductory information and safety warn-
ings on page 83.

Switching on the City Safe Drive

CAUTION The City Safe Drive system is automatically switched on after turning on the igni-
tion.
If the vehicle starts to roll after the City Safe Drive system is triggered, use the
foot pedal to break. Switching the City Safe Drive system on and off again
The City Safe Drive system is switched off by pressing the button » Fig. 83 in the
front centre console. 

84 Driving
When the City Safe Drive system is switched off while the vehicle is travelling at a
speed between 5–30 km/h (3–19 mph), the warning light   will light up in the
Special driving situations
instrument cluster display.
You can switch on the City Safe Drive system again with the button » Fig. 83. The
warning light   lights up for around 5 seconds in the instrument cluster dis-
play.
The City Safe Drive system must be switched off in the following cases.
› When the vehicle is being towed away.
› When the vehicle is driven though an automatic car wash.
› When the vehicle is on a rolling test bench.
› When the laser sensor is faulty.
› After force is applied to the laser sensor.
› When driving off-road (overhanging branches). Fig. 84 Vehicle in the range of a curve/motorcycles driving ahead outside of
› When objects are extending into the area above the bonnet, e.g. when a rood the laser sensor range
load sticks out far ahead.
› When the windscreen is damaged in the region of the laser sensor. 

Fig. 85
Other vehicles changing lanes
Laser sensor

 First read and observe the introductory information and safety warn-
ings on page 83.

Possible impairment of the laser sensor

If the functioning of the laser sensor is impaired by e.g. heavy rain, snow or slush,
the City Safe Drivesystem will temporarily shut down. The warning light  flashes
slowly in the instrument cluster display.
If the laser sensor is no longer impaired, the City Safe Drive system will automati-
cally switch back to ready. The warning light  goes out. 
 First read and observe the introductory information and safety warn-
ings on page 83.

The following and similar situations require special attention of the driver:
Driving around a bend
When driving into or out of “protracted” bends, it is possible for the laser sensor
to respond to a vehicle in the adjacent lane » Fig. 84 -  causing it to apply the
brakes to your vehicle.
Narrow vehicles or vehicles travelling side by side
Narrow vehicles or vehicles travelling side by side are not detected by the laser
sensor until they are in the range of the sensor » Fig. 84 - . This is especially
true for narrow vehicles, such as motorcycles. 

Assist systems 85
Other vehicles changing lanes
Vehicles which move into your lane close to your vehicle can trigger an unexpec-
ted braking of the City Save Drive system » Fig. 85. 

86 Driving
 › Head, thorax, driver and front seat passenger side airbag with head restraint
Safety function;
› Anchoring points for child seats using the ISOFIX system.
› Anchoring points for child seats using the TOP TETHER system.
Passive Safety › Height-adjustable rear head restraints;
› Height-adjustable steering column.
The specified safety equipment works together, in order to optimally protect you
General information and those travelling with you in accident situations.
The safety equipment does not protect you or the people travelling with you, if
 Introduction you or your occupants adopt an incorrect seated position or the equipment is not
correctly adjusted or used.
This chapter contains information on the following subjects:
If the seat belt is not fastened properly, this may result in injuries if an airbag is
Safety equipment 87 activated in the event of an accident. 
Before setting off 87
What influences the driving safety? 88
Before setting off
In this section you will find important information, tips and notes on the subject
of passive safety in your vehicle.
We have combined everything here which you should be familiar with, for exam-
ple, regarding seat belts, airbags, child seats and safety of children.
 First read and observe the introductory information and safety warn-
ings on page 87.

For your own safety and the safety of the people travelling with you, please pay
attention to the following points before setting off.
WARNING › Ensure that the lighting and the turn signal system are functioning properly.
■ This chapter contains important information on how to use the vehicle for › Check the tyre inflation pressure.
the driver and his occupants. › Ensure that all of the windows offer good visibility to the outside.
■ You can find further information on safety concerning you and those travel- › Secure all items of luggage » page 44, Luggage compartment.
ling with you in the following chapters of this owner's manual. › Ensure that no objects can obstruct the pedals.
■ The complete on-board literature should always be in the vehicle. This ap- › Adjust the rear mirror and the front seat to your body size.
plies in particular, if you rent out or sell the vehicle.  › Advise your passengers on the back seats to adjust the head restraints to their
body size.
› Protect children in suitable child seats with correctly fastened seat
belts » page 100, Transporting children safely.
Safety equipment › Adopt the correct seated position » page 88, Correct seated position. Tell your
passengers to assume the correct seated position.
 First read and observe the introductory information and safety warn-
ings on page 87.
› Correctly fasten the seat belt. Also inform passengers to fasten the seat belt
correctly » page 93, Fastening and unfastening seat belts. 

The following list contains only part of the safety equipment in your vehicle.
› Three-point seat belts for all the seats.
› Belt force limiters for the front seats.
› Belt tensioners for the front seats.
› Front airbag for the driver and the front passenger.

Passive Safety 87
 What influences the driving safety? WARNING
As the driver, observe the following instructions.
 First read and observe the introductory information and safety warn-
ings on page 87.
■ Always assume the correct seated position before setting off and do not
change this position while driving. Also advise your passengers to adopt the
The driver is fully responsible for himself and his occupants. If your driving safety correct seated position and not to change this position while the car is mov-
is effected, you place yourself and the oncoming traffic at risk. ing.
■ Maintain a distance of at least 25 cm to the steering wheel. Not maintaining
The following guidelines must therefore be observed. this minimum distance will mean that the airbag system will not be able to
› Do not become distracted from concentrating on the traffic situation, e.g. by properly protect you – hazard!
your passengers or mobile phone calls. ■ When driving, hold the steering wheel with both hands firmly on the outer
› Never drive when your driving ability is impaired, e.g. due to medication, alcohol edge in the 9 o'clock and 3 o'clock position. Never hold the steering wheel in
or drugs. the 12 o'clock position or in any other way (e.g. in the middle or inner edge of
› Keep to the traffic regulations and the permissible speed limit. the steering wheel). In such cases, you could severely injure the arms, hands
› Always adjust the driving speed to the road, traffic and weather conditions. and head when the driver airbag is deployed.
› Take regular breaks on long journeys – at least every two hours. 
■ Ensure that there are no objects in the driver's footwell, as these may get
caught in the pedal apparatus when driving or braking. You would then no
longer be able to operate the clutch, brake or acceleration pedals.
Correct seated position
WARNING
 Introduction
As the front passenger, observe the following instructions.
This chapter contains information on the following subjects: ■ Maintain a distance of at least 25 cm to the dash panel. Not maintaining this
minimum distance will mean that the airbag system will not be able to proper-
Correct seated position for the driver 89 ly protect you – risk to life!
Correct seated position for the front passenger 89 ■ Always keep your feet in the footwell when the car is being driven – never
Correct seated position for the passengers in the rear seats 89 place your feet on the instrument panel, out of the window or on the surfaces
Examples of incorrect seated positions 89 of the seats. You will be exposed to increased risk of injury if it becomes nec-
essary to apply the brake or in the event of an accident. If an airbag is de-
WARNING ployed, you may suffer fatal injuries when adopting an incorrect seated posi-
tion! 
Observe the following instructions for the correct seated position.
■ The front seats and the head restraints must always be adjusted according
to height, so that the occupants can be protected as effectively as possible.
■ If the occupant adopts an incorrect seated position, he is exposed to life-
threatening injuries, in case he is hit by a deployed airbag.
■ If the occupants on the rear seats are not sitting upright, the risk of injury is
increased due to incorrect routing of the seat belt.
■ The seat backrests must not be tilted too far back when driving, as this will
impair the function of the seat belts and of the airbag system – risk of injury!

88 Safety
 Front passenger adjustment » page 41, Adjusting the front seats. 
Correct seated position for the driver

Fig. 86 Correct seated position for the passengers in the rear seats
Correct seated position for the
driver
 First read and observe the introductory information and safety warn-
ings on page 88.

To reduce the risk of injury in the event of a sudden braking manoeuvre or an ac-
cident, the occupants on the rear seats must observe the following.
› Adjust the head restraint so that the top edge of the head restraint is at the
same level as the upper part of your head.
› Correctly fasten the seat belt » page 93.
› Use a suitable child restraint system if transporting children in the vehi-
 First read and observe the introductory information and safety warn-
ings on page 88.
cle » page 100, Transporting children safely. 

For your own safety and to reduce the risk of injury in the event of an accident,
we recommend the following setting. Examples of incorrect seated positions
› Adjust the steering wheel so that the distance A » Fig. 86 between the steer-
ing wheel and your chest is at least 25 cm.
› Adjust the driver’s seat in the forward/back direction so that the pedals can be  First read and observe the introductory information and safety warn-
ings on page 88.
fully depressed with slightly bent legs.
Maximum seat belt protection is only achieved if seat belts are fastened correctly.
› Adjust the seat backrest so that the highest point of the steering wheel can be
reached with your arms at a slight angle. Incorrect seated positions considerably reduce the protective functions of the
› Correctly fasten the seat belt » page 93. seat belts and therefore increase the risk of injury due to an incorrect routing of
the seat belt.
Driver seat adjustment » page 41, Adjusting the front seats. 
The driver is fully responsible for himself and passengers, especially children.
Never allow a passenger to adopt an incorrect seated position when the car is
Correct seated position for the front passenger moving.
The following list contains instructions which, if not observed, may cause serious
 First read and observe the introductory information and safety warn-
ings on page 88.
injuries or death. This list is not complete, however we would like you to familiar-
ise yourself with this subject.
For the safety of the front passenger and to reduce the risk of injury in the event Observe the following instructions while driving.
of an accident, we recommend the following setting. › Do not stand up.
› Position the front passenger seat back as far as possible. The front passenger › Do not stand on the seats.
must maintain a distance of at least 25 cm to the dash panel so that the airbag › Do not kneel on the seats.
offers the greatest possible safety if it is deployed. › Do not tilt the seat backrest too far back.
› Correctly fasten the seat belt » page 93. › Do not lean against the dash panel.
In exceptional cases the front passenger airbag can be deactivated » page 98, › Do not lie on the rear seats.
Deactivating airbags. › Do not sit only on the front part of the seat.
› Do not sit facing to the side. 

Passive Safety 89
› Do not lean out of the window.
› Do not put your feet out of the window.
› Do not put your feet on the dash panel.
› Do not put your feet on the seat cushion.
› Do not allow anybody to travel in the footwell.
› Do not drive without fastening your seat belt.
› Do not delay in the luggage compartment. 

90 Safety
 WARNING
Seat belts
■ Fasten your seat belt before each journey – even when driving in town! This
also applies to the passengers seated at the rear – risk of injury!
Using seat belts ■ Expectant women must also always wear a seat belt. This is the only way of
ensuring optimal protection for the unborn child » page 93.
■ Maximum seat belt protection is only achieved if you are correctly seat-
 Introduction
ed » page 88, Correct seated position.
■ The seat backrests of the front seats must not be tilted too far to the rear
Fig. 87 otherwise the seatbelts can lose their effectiveness.
Driver wearing seat belt
WARNING
Observe the following instructions for the correct routing of the seat belt.
■ Always ensure that the webbing of the seat belts is properly routed. Seat
belts which are not correctly adjusted can themselves cause injuries even in
minor accidents.
■ A seat belt which is hanging too loose can result in injuries as your body is
moved forward by the kinetic energy produced in an accident and is then sud-
This chapter contains information on the following subjects: denly held firm by the belt.
The physical principle of a frontal collision 92 ■ The belt webbing must not run across solid or fragile objects (e.g. specta-

Fastening and unfastening seat belts 93 cles, ball-point pens, bunches of keys etc.). Such objects can cause injury.

Seat belts that are fastened correctly offer good protection in the event of an ac-
cident. They reduce the risk of an injury and increase the chance of survival in the WARNING
event of a major accident. Observe the following instructions for handling the seat belts.
Correctly fastened seat belts hold occupants of the car in the correct seated posi- ■ The belt webbing must not be jammed in-between at any point or twisted,
tion » Fig. 87. or chafe against any sharp edges.
■ Make sure you do not catch the seat belt when closing the door.
The seat belts reduce the kinetic energy (energy of motion) to a considerable ex-
tent. They also prevent uncontrolled movements which, in turn, may well result in
severe injuries. WARNING
Occupants of a vehicle who have correctly fastened their seat belts have the ma- Observe the following instructions for the proper use of the seat belts.
jor benefit of the fact that the kinetic energy is absorbed as effectively as possi- ■ Never use one seat belt to secure two persons (including children). The
ble by the belts. seatbelt must not be placed over a child who is sitting on the lap of another
The structure of the front end of the vehicle and other passive safety measures, passenger.
■ The lock tongue should only be inserted into the lock which is the correct
such as the airbag system, also contribute to the kinetic energy being reduced as
effectively as possible. The energy produced is thus absorbed and there is less one for your seat. Wrong use of the safety belt will reduce its capacity to pro-
risk of injury. tect and the risk of injury increases. 

Particular safety aspects must be observed when transporting children in the ve-
hicle » page 100, Transporting children safely.

Seat belts 91
 WARNING (Continued) The physical principle of a frontal collision
■ The slot of the belt tongue must not be blocked, otherwise the belt tongue
will not lock in place properly.
■ Many layers of clothing and loose clothing (e. g. a winter coat over a jacket)
do not allow you to be correctly seated and impairs proper operation of the
seat belts.
■ It is prohibited to use clamps or other objects to adjust seat belts (e. g. for
shortening the belts for smaller persons).
■ The seat belts for the rear seats can only fulfil their function reliably when
the seat backrests are correctly locked into position » page 43, Folding the
rear seats forward.

WARNING Fig. 88 Driver without a fastened seat belt/rear passenger without a fas-
tened seat belt
Observe the following instructions for proper maintenance of the seat belts.
■ The belt webbing must always be kept clean. Soiled belt webbing may im-
pair proper operation of the inertia reel » page 112, Seat belts.
■ The seat belts must not be removed or changed in any way. Do not attempt
 First read and observe the introductory information and safety warn-
ings on page 91.

to repair the seat belts yourself. As soon as the vehicle is moving, so-called kinetic energy (the energy of motion)
■ Check the condition of all the seat belts on a regular basis. If any damage to is produced both in terms of the car as well as in terms of the occupants.
the seat belts, seat belt connections, inertia reel or the lock is detected, the The magnitude of this kinetic energy depends essentially on the speed at which
relevant seat belt must be replaced by a specialist garage. the vehicle is travelling and on the weight of the vehicle including the occupants.
■ Damaged seat belts which have been subjected to stress in an accident and
The greater the speed and weight increase, the greater the amount of energy
were therefore stretched, must be replaced – this is best done by a specialist which has to be absorbed in the event of an accident.
garage. The anchorage points of the belts must also be inspected. The an-
chorage points for the belts should also be checked. The speed of the vehicle is the most important factor. Doubling the speed of the
vehicle from 25 km/h up to 50 km/hour increases the kinetic energy four times.

Note The idea that it is possible to support your body with your hands in a minor acci-
dent is incorrect. Even in a collision at only a low speed, the forces acting on the
The national legal requirements must be observed when using seat belts.  body are such that it is no longer possible to support your body.
Even if you only drive at a speed of 30-50 km/h, the forces that your body is ex-
posed to in the event of an accident can exceed a metric ton (1000 kg).
For example, a person's weight of 80 kg “increases” to 4.8 tons (4800 kg) at
50 km/h.
In the event of a frontal collision, occupants of the car not wearing a seat belt, are
thrown forward and strike in an uncontrolled way parts of the interior of the car,
such as steering wheel, dash panel or windscreen » Fig. 88 – . In certain circum-
stances you could even be thrown out of the vehicle, which could cause life
threatening or even fatal injuries. 

92 Safety
It is also important that rear passengers fasten their seat belts, as they could oth- › Use the lock tongue to slowly pull the webbing over your chest and pelvis.
erwise be thrown through the vehicle in an uncontrolled manner in the event of › Insert the lock tongue into the belt buckle for the seat until audibly it clicks into
an accident. place » Fig. 89 - .
A rear seat passenger who has not fastened the seat belt is a danger not only to › Pull on the belt to check that it has engaged correctly in the lock.
himself but also for those seated at the front » Fig. 88 – .  A plastic knob in the belt webbing holds the belt tongue in a position which is
easy to get hold of.
It is important that the belt webbing is properly routed to ensure seat belts offer
Fastening and unfastening seat belts the maximum protection.
The shoulder part of the seat belt must never run across the neck but must
roughly run over the middle of the shoulder and fit snugly against the chest. The
lap part of the belt must run across the pelvis, must not be positioned across the
stomach and must always fit snugly » Fig. 90 – .
Expectant women must also always wear a seat belt. This is the only way of en-
suring optimal protection for the unborn child.
On expectant mothers, the lap part of the belt must be positioned as low as pos-
sible on the pelvis to avoid exerting any pressure on the lower abdomen » Fig. 90
– .

Fig. 89 Fastening/unfastening the seat belt Releasing

Release the seat belt only when the vehicle is stationary.
› Press the red button in the belt buckle » Fig. 89 – , the lock tongue pops out.
› Manually guide the belt back so that it is easier to fully roll up the webbing, the
seat belt does not twist.

CAUTION
When releasing the seatbelt ensure that the tongue of the lock does not damage
the door trim or other parts of the interior. 

Inertia reels and belt tensioners

Fig. 90 Routing of belt webbing over the shoulders and the lap belt/Rout-
ing of belt webbing for an expectant mother
 Introduction

 First read and observe the introductory information and safety warn-
ings on page 91.
This chapter contains information on the following subjects:
Inertia reels 94
Fastening Belt tensioners 94 
› Correctly adjust the front seat before fastening the seat belt » page 88, Correct
seated position.

Seat belts 93
 Inertia reels WARNING
Any work on the belt tensioner system including removal and installation of

■
First read and observe the introductory information given on page 93.
system components because of other repair work, must only be carried out by
a specialist garage.
Each seat belt is equipped with an inertia reel. ■ The protective function of the system is only adequate for a single accident.
If the belt tensioners have been deployed, it is then necessary to replace the
When pulling slowly on the seat belt, the belt can move freely. When pulling
entire system.
sharply on the seat belt, the movement is locked by the inertia reel.
The belts also lock when full braking, when the car accelerates, when driving
downhill and when cornering. Note
■ Smoke is generated when the belt tensioners are deployed. This is not an indi-
WARNING cation of a fire in the vehicle.
■ When disposing of the vehicle or parts of the belt tensioner system, it is impor-
If the seat belt does not lock when pulling sharply on it, have it inspected im-
tant to comply with national legal requirements. ŠKODA service partners are fa-
mediately by a specialist garage. 
miliar with these regulations and will be able to provide you with detailed infor-
mation. 

Belt tensioners

 First read and observe the introductory information given on page 93.

Safety for the driver and front passenger wearing their seat belts is enhanced by
the belt tensioners fitted to the inertia reels of the front three-point seat belts.
The three-point seat belts are automatically tensioned in the event of a frontal
collision of a certain severity. The belt tensioners can also be deployed if the seat
belts are not fastened.
The fastened three-point seat belts are automatically tensioned in the event of a
frontal or side collision of a certain severity.
Belt tensioners are not activated in the event of minor frontal collisions, side and
rear-end collisions, in the case of a rollover and also not in accidents in which no
major forces are produced from the front.

94 Safety
 System description
Airbag system

Description of the airbag system  First read and observe the introductory information and safety warn-
ings on page 95.

The functional status of the airbag system is indicated by the indicator light  in
 Introduction the instrument cluster » page 18.
When the airbags are deployed, they fill with gas and inflate.
This chapter contains information on the following subjects:
A grey white or red, non-harmful gas is released when the airbag is inflated. This
System description 95 is perfectly normal and is not an indication of a fire in the vehicle.
Airbag deployment 95
Depending on the vehicle equipment, the airbag system consists of the
WARNING following modules.
› Electronic control unit.
■ An airbag can only offer you optimal protection in combination with a fas- › Front airbag for the driver and the front passenger » page 96.
tened seat belt. › Side airbags Head-thorax » page 97;
■ The airbag is not a substitute for the seat belt, but instead forms part of the › Airbag warning light in the instrument cluster » page 18,  Airbag system.
complete passive vehicle safety concept. › Key switch for the front passenger airbag » page 99.
■ To ensure passengers are protected with the greatest possible effect when › Warning light for the front passenger airbag deactivation/activation in the mid-
the airbag is deployed, the front seats must be correctly adjusted to match dle of the dash panel » page 99.
the body size » page 88, Correct seated position.
■ If you do not fasten the seat belts when driving, lean too far forward or Note
adopt an incorrect seated position, you are exposing yourself to increased risk
of injury in the event of an accident. ■ The airbag system needs no maintenance during its working life.
■ If you sell your vehicle, provide the complete vehicle documentation to the new
owner. Please note that the information relating to the possibility of deactivating
WARNING the front passenger airbag must be included!
■ When disposing of vehicle or parts of the airbag system, it is important to com-
Observe the following instructions for handling the airbag system.
■ If there is a fault, the airbag system must be checked by a specialist garage ply with the national legal requirements. 

immediately. Otherwise, there is a risk that the airbag will not be deployed in
the event of an accident.
■ No modifications of any kind must be made to parts of the airbag system. Airbag deployment
■ Any work on the airbag system including the installation and removal of sys-
tem components due to other repair work (e.g. removal of the steering wheel)
must only be carried out by a specialist garage.
 First read and observe the introductory information and safety warn-
ings on page 95.
■ Never make any changes to the front bumper or bodywork.
The airbags inflate in fractions of a second and at a high speed in order to be able
■ It is prohibited to manipulate individual parts of the airbag system as this
to offer additional protection in the event of an accident.
might result in the airbag being deployed.
■ The protective function of the airbag system is sufficient for only one acci- The airbag system is only functional when the ignition is switched on.
dent. The airbag system must then be replaced if the airbag has been de- In certain accident situations, several airbags may be deployed simultaneously. 
ployed. 

Airbag system 95
The airbags are not deployed in the case of minor frontal and side collisions, rear-
end collisions, tilting of the vehicle and vehicle rollover.
Front airbags

Deployment factors
It is not possible to generally determine which deployment conditions apply to
the airbag system in every situation. An important role is played by factors such
as the type of object that the vehicle hits (hard/soft), the impact angle, vehicle
speed etc.
A decisive factor for the deployment of the airbags is the deceleration which oc-
curs. The control unit analyses the nature of the collision and activates the rele-
vant restraint system.
If the vehicle deceleration which occurs and is measured during the collision re-
mains below the prescribed reference values specified in the control unit, the air-
bags are not deployed although the vehicle may well suffer severe damage to the Fig. 91 Driver's airbag in the steering wheel/front passenger airbag in the
bodywork as a consequence of the accident. dash panel

The following airbags will be deployed in the event of a severe frontal collision.
› Driver’s front airbag.
› Front passenger airbag.
The following airbags will be deployed in the event of a severe side collision.
› Side airbags on the side of the accident.
In the event of an accident in which the airbags are deployed:
› the interior lighting comes on (if the switch for the interior light is in the door
contact position),
› the hazard warning light is switched on;
› all the doors are unlocked;
› the fuel supply to the engine is interrupted.  Fig. 92 Safe distance to steering wheel/inflated airbags

Airbag overview  First read and observe the introductory information given on page 96.

In the event of a severe frontal collision, the front airbag system offers additional
 Introduction protection for the head and chest area of the driver and front passenger.

This chapter contains information on the following subjects: The front airbag for the driver is housed in the steering wheel » Fig. 91 – .

Front airbags 96 The front airbag for the front seat passenger is located in the dash panel above
Side airbags Head-Thorax 97  the stowage compartment » Fig. 91 – .
When the airbags are deployed, they inflate in front of the driver and front pas-
senger » Fig. 92 - . The forward movement of the driver and of the front pas-
senger is cushioned when they make contact with the fully inflated airbag and
the risk of injury to head and chest is thus reduced. 

96 Safety
 WARNING Side airbags Head-Thorax
Correct seated position
■ For the driver and front passenger, it is important to maintain a distance of
at least 25 cm to the steering wheel or dashboard A » Fig. 92. Not maintain-
ing this minimum distance will mean that the airbag system will not be able to
properly protect you – hazard! The front seats must always also be correctly
adjusted to match the body size of the occupant.
■ The airbag develops enormous forces when triggered, which can lead to in-
juries if the sitting position or seated position is not correct.
■ There must not by any further persons, animals or objects positioned be-
tween the front seated occupants and the deployment area of the airbag.

Fig. 93 Place of installation of the side airbag/deployment area of the side

WARNING
airbag
Front airbag and transporting children
■ Never transport children on the front seat of a vehicle without using a prop-
er restraint system. If airbags are deployed in the event of an accident, the
child might suffer severe or even fatal injuries!
 First read and observe the introductory information given on page 96.

In the event of severe side collisions, the side airbag system Head-Thorax pro-
■ The front passenger airbag must be deactivated if using a rear-facing child
vides additional protection for the upper body (chest, stomach and pelvis) of pas-
seat on the front passenger seat » page 99, Deactivating the front passen-
sengers in the vehicle.
ger airbag. If this is not done, there is a risk of the child suffering severe or
even fatal injuries if the front passenger airbag is deployed. When transport- The side airbags are housed in the upholstery of the seat backrests of the front
ing a child on the front passenger seat, pay attention to any relevant national seats » Fig. 93 – .
regulations regarding the use of child safety seats.
When the side airbags » Fig. 93 -  are triggered, the belt tensioner is also de-
ployed automatically on the relevant side.
WARNING The load of the occupants is cushioned when plunging into the fully inflated air-
General bag and the risk of injury to the head and upper body (chest, stomach and pelvis)
■ The steering wheel and the surface of the airbag module in the dash panel is reduced on the side facing the door.
on the passenger side must not have stickers attached, be covered or modi-
fied in any other way. These parts should only be cleaned with a cloth that is WARNING
dry or has been moistened with water. No objects such as cup holders, mobile
Observe the following instructions for the correct seated position.
phone mounts, etc. must be attached to the covers of the airbag modules or ■ Your head should never be positioned in the deployment area of the side
be located within their immediate vicinity.
airbag. You might suffer severe injuries in the event of an accident. This ap-
■ Never place objects on the surface of the front passenger airbag module in
plies in particular to children who are transported without using a suitable
the dash panel. 
child safety seat » page 101, Child safety and side airbag. 

Airbag system 97
 WARNING (Continued) WARNING (Continued)
■ There must not be any further persons, animals as well as objects posi- ■ Any seat or protective covers which you fit to the driver or front passenger
tioned between the occupants and the deployment area of the airbag. No ac- seats must only be of the type expressly authorized by ŠKODA. In view of the
cessories, such as cup holders, should be attached to the doors. fact that the airbag inflates out of the backrest of the seat, use of non-ap-
■ If children adopt an incorrect seated position when travelling, they may be proved seat or protective covers would considerably impair the protective
exposed to an increased risk of injury in the event of an accident. This can re- function of the side airbag.
sult in serious injuries » page 100, Child seat. ■ Any damage to the original seat covers in the area of the side airbag module
must be repaired immediately by a specialist garage.
■ The airbag modules in the front seats must not display any damage, cracks
WARNING or deep scratches. It is not permissible to use force in order to open the mod-
The airbag control unit operates using pressure sensors located in the front ules. 

doors. For this reason, no adjustments may be carried out to the doors or door
panels (e.g. installation of additional loudspeakers). Resulting damage can
have a negative impact on the function of the airbag system. Any work on the
front doors and door panels must be carried out by a specialist garage. The
Deactivating airbags
following instructions must be observed.
■ Never drive with inner door panels removed.  Introduction
■ Never drive if parts of the inner door panel have been removed and the re-
sulting openings have not been properly sealed. This chapter contains information on the following subjects:
■ Never drive if the loudspeakers in the doors have been removed, unless the
Deactivating airbags 98
loudspeaker openings have been properly sealed.
■ Always make sure that the openings are covered or filled if additional loud-
Deactivating the front passenger airbag 99 
speakers or other equipment parts have been installed in the inner door pan-
els.
■ Always have work carried out by a ŠKODA service partner or a professional
Deactivating airbags
specialist garage.

WARNING
 First read and observe the introductory information given on page 98.

Deactivating an airbag should be considered in cases such as the ones below.

■ Only hang light items of clothing on the hooks fitted in the vehicle. Never › If using a rear-facing child seat on the front passenger seat (due to different le-
leave any heavy or sharp-edged objects in the pockets of the items of cloth- gal regulations, the airbag must be deactivated if using a forwards-facing child
ing. seat in some countries) » page 100, Transporting children safely.
■ Ensure that there are no excessive forces, such as violent knocks, kicks etc., › If it is not possible to maintain a distance of at least 25 cm between the middle
impact on the backrests of the seats otherwise the system may be damaged. of the steering wheel and chest, despite the driver's seat being correctly adjus-
The side airbags would not be deployed in such a case! ted.
› If special attachments are required in the area of the steering wheel because of
a physical disability.
› If different seats have been fitted (e.g. orthopaedic seats without side airbags).
The front passenger airbag can be switched off with the key-operated
switch » page 99. 

98 Safety
We recommend that you ask a ŠKODA service partner to deactivate any other air- Switching off
bags. › Switch off the ignition.
Monitoring the airbag system
› Use the key to turn the slot of the key switch into position 2 » Fig. 94 OFF.
The operational capability of the airbag system is monitored electronically, includ-
› Check that warning light 3      in the middle of the dash panel
lights up after the ignition is switched on.
ing when one of the airbags is switched off.
Switching on
Airbag deactivated using diagnostic equipment
› The warning light  lights up for approx. 3 seconds after switching on the igni- › Switch off the ignition.
tion and then flashes again for approx. 12 seconds. › Use the key to turn the slot of the key switch into position 1 » Fig. 94 ON.
› Check that warning light 3      in the middle of the dash panel
Front passenger airbag deactivated using the key switch in the storage com- does not light up after the ignition is switched on.
partment
› The warning light  lights up for approx. 3 seconds after switching on the igni- WARNING
tion.
› The warning light      3 » Fig. 94 on page 99 lights up after ■ The driver is responsible for whether the airbag is switched on or switched
switching on the ignition. off.
■ Only switch off the airbag when the ignition is switched off! Otherwise a

Note fault can occur in the system for deactivating the airbag.
■ If the warning light      flashes, the front passenger airbag
■ The national regulations for switching off airbags must be observed. will not be deployed in the event of an accident! Have the airbag system
■ A ŠKODA service partner will be able to inform you which, if any, of your vehi- checked by a specialist garage immediately. 
cle's airbags can or must be deactivated. 

Deactivating the front passenger airbag

Fig. 94 Key switch for front passenger airbag/warning light for front pas-
senger airbag activation/deactivation

 First read and observe the introductory information given on page 98.

Only the front passenger airbag is deactivated with the key switch.

Airbag system 99
 WARNING (Continued)
Transporting children safely ■ Children are at increased risk of injury in the event of an accident if they lean
forward or are not correctly positioned when the vehicle is moving, e.g. an in-
Child seat correct seated position. This particularly applies to children who are transpor-
ted on the front passenger seat as they can suffer severe, or even fatal inju-
ries if the airbag system is deployed!
 Introduction ■ Pay particular attention to the information provided by the manufacturer of
the child safety seat regarding the correct routing of the belt. Seat belts
This chapter contains information on the following subjects:
which are not correctly adjusted can themselves cause injuries even in minor
Use of a child seat on the front passenger seat 101 accidents.
Child safety and side airbag 101 ■ Safety belts must be checked to ensure that they are running properly. One

Classification of child seats 102 should also ensure that the belt is not damaged by sharp-edged fittings.
■ The front passenger airbag must be deactivated if using a rear-facing child
Use of child seats fastened with a seat belt 102
seat on the front passenger seat. Further information » page 101, Use of a
Children are generally safer on the rear seats than on the front passenger seat. child seat on the front passenger seat.
In contrast to adults, the muscles and bone structure of children are not yet fully
developed. Thus children are exposed to increased risk of injury. Note
Children should be transported in accordance with the relevant statutory provi- We recommend that you use child seats from ŠKODA Original Accessories. These
sions. child seats were developed and also tested for use in ŠKODA vehicles. They meet
Child seats that comply with the ECE-R 44 standard must be used. The ECE-R the ECE-R 44 standard. 

standard stands for: Economic Commission for Europe – Regulation.

Child seats that comply with the ECE-R 44 standard are identified with a test
mark that cannot be removed: a large E within a circle with the test number be-
low.

WARNING
■ The national legal requirements must be observed when using child seats.
■ One should never carry children, and also not babies! - on one's lap.
■ Never leave children unattended in the vehicle. Certain outside climatic con-
ditions can cause life-threatening temperatures in the vehicle.
■ The child must be secured in the vehicle during the entire journey! Other-
wise, the child would be thrown through the vehicle in the event of an acci-
dent, causing fatal injuries to both the child and other occupants.

100 Safety
 Use of a child seat on the front passenger seat WARNING
Never use a backwards-facing child restraint system on a seat that is protected ■ The front passenger airbag must be deactivated if using a rear-facing child
by an active airbag installed in front of it. This could cause the child severe injury seat on the front passenger seat » page 98, Deactivating airbags.
or even death. ■ Never use a rear-facing child seat on the front passenger seat if the passen-
ger airbag is activated. This child safety seat is positioned in the deployment
area of the front passenger airbag. The airbag may cause the child severe, or
Fig. 95
even fatal injuries, in the event of it being deployed.
Sticker on the B column on the
■ This is also clearly stated on the sticker which is located on the B column on
front passenger side.
the front passenger side » Fig. 95. The sticker is visible upon opening the
front passenger door. In some countries, the sticker is affixed to the front pas-
senger sun visor.
■ With child safety seats in groups 2 or 3, make sure that the loop-around fit-
tings attached to the child seat headrest is positioned in front of or at the
same height as the loop-around fittings on the B pillar on the passenger side.
■ As soon as the rear-facing child seat is no longer being used on the passen-
ger seat, the front passenger airbag should be re-activated again. 

 First read and observe the introductory information and safety warn-
ings on page 100.

For safety reasons, we recommend that you install child seats on the rear seats Child safety and side airbag
whenever possible.
The following instructions must be followed when using a child seat on the front
passenger seat.
› The front passenger airbag must be deactivated if using a rear-facing child
seat » .
› If possible, adjust the front passenger seat backrest so that it is as vertical, so
as to ensure secure contact between the passenger seat backrest and the back
of the child seat.
› If possible, move the front passenger seat backwards so that there is no con-
tact between the front passenger seat and the child seat behind it.
› With child safety seats in groups 2 or 3, make sure that the loop-around fittings
attached to the child seat headrest is positioned in front of or at the same Fig. 96 Incorrect seated position of a child who is not properly secured –
height as the loop-around fittings on the B pillar on the passenger side. risk from the side airbag/child properly protected by child seat
› Set the height-adjustable front passenger seat as high up as possible.
› Place and fasten the child seat on the seat and the child in the child seat ac-
cording to the specifications in the manufacturer's user manual of the child
seat .
 First read and observe the introductory information and safety warn-
ings on page 100.

The child must not be positioned in the deployment area of the side air-
bag » Fig. 96 – . 

Transporting children safely 101

There must be sufficient room between the child and the deployment area of the Group Front passenger seat Rear seats
side airbag so that the airbag can provide as much protection as possible » Fig. 96
1
– . U U
9-18 kg
WARNING 2
U U
15-25 kg
■ Children must never be seated with their head in the deployment area of 3
the side airbag – risk of injury! U U
22-36 kg
■ Do not place any objects within the deployment area of the side airbags –
risk of injury!  U Child seat category “Universal” - a child seat designed to be attached to
the seat using the seat belt. 

Classification of child seats

Fastening systems
 First read and observe the introductory information and safety warn-
ings on page 100.  Introduction
Classification of child seats according to the ECE-R 44 standard.
This chapter contains information on the following subjects:
Group Weight of the child Approximate age Anchor eyelets for the ISOFIX system 103
0 up to 10 kg up to 9 months Use of child seats with the ISOFIX system 103
0+ up to 13 kg up to 18 months Anchor eyelets for the TOP TETHER system 104 
1 9-18 kg up to 4 years
2 15-25 kg up to 7 years
3 22-36 kg over 7 years 

Use of child seats fastened with a seat belt

 First read and observe the introductory information and safety warn-
ings on page 100.

Overview of the usability of child seats fastened with a seat belt on each of the
seats in accordance with the ECE-R 16 standard.

Group Front passenger seat Rear seats

0
U U
to 10 kg
0+
U U
to 13 kg

102 Safety
 Anchor eyelets for the ISOFIX system WARNING
■ Always refer to the instructions from the manufacturer of the child seat
when installing and removing a child seat with the ISOFIX system.
■ Never attach other child seats, belts or objects to the anchor eyelets inten-
ded for the installation of a child seat with the ISOFIX system – risk to life!

Note
■ A child seat fitted with the ISOFIX system can only be mounted in a vehicle fit-
ted with an ISOFIX system if the child seat has been approved for this type of ve-
hicle. Further information is available from a ŠKODA Partner.
■ Child seats with the ISOFIX system can be purchased from ŠKODA Original Ac-
Fig. 97 Identification versions of anchor eyelets for child safety seats cessories. 

 First read and observe the introductory information given on page 102.

There are two lashing eyes between the rear exterior seat backrest and the sur-
face of the seat itself on both sides for fixing the ISOFIX system » Fig. 97 child
seat in place.

Use of child seats with the ISOFIX system

 First read and observe the introductory information given on page 102.

Overview of the usability of child seats with the ISOFIX system on each of the
seats in accordance with the ECE-R 16 standard.

Size category
Group Front passenger seat Rear seats
of the child seata)
0
E X IL-SU
to 10 kg
E
0+
D X IL-SU
to 13 kg
C 

Transporting children safely 103

 Size category
Group Front passenger seat Rear seats
of the child seata)
D
C
1 IL-SU
B X
9-18 kg IUF
B1
A
a) The size category is shown on the label attached to the child seat.

IL-SU The seat is suited for installation of an ISOFIX child seat with “Semi-
WARNING
Universal” approval. The category “Semi-Universal” means that the child
seat with the ISOFIX system is approved for your vehicle. Observe the list ■ Always refer to the instructions from the manufacturer of the child seat
of vehicles that comes with the child seat. when installing and removing a child seat with the TOP TETHER system.
IUF The seat is suitable for the installation of an ISOFIX child seat with ■ Only use child seats with the TOP TETHER system on the seats with the
“Universal” approval and attachment with the TOP TETHER belt. locking eyes.
X The seat is not fitted with fixing eyes for the ISOFIX system.  ■ Only ever attach one belt from the child seat to a locking eye.
■ On no account should you equip your vehicle, e.g. mount screws or other an-
chorage points. 

Anchor eyelets for the TOP TETHER system

Fig. 98
Rear seat: TOP TETHER

 First read and observe the introductory information given on page 102.

The anchor eyelets for attaching the belt of a child seat with the TOP TETHER
system are located on the back of the rear seat backrests » Fig. 98.

104 Safety
 CAUTION
General Maintenance
Do not wash your vehicle in bright sunlight – risk of paint damage.

Taking care of and cleaning the vehicle For the sake of the environment
Only wash the vehicle at washing bays intended for this purpose. 

Washing your car

Washing by hand
 Introduction
This chapter contains information on the following subjects:  First read and observe the introductory information and safety warn-
ings on page 105.
Washing by hand 105 Soak the dirt with plenty of water and rinse as well as possible.
Automatic car wash systems 105
Washing with a high-pressure cleaner 106 Clean the vehicle with a soft sponge, a washing glove or a washing brush. Work
from the top to the bottom – starting with the roof.
The best way to protect your vehicle against harmful environmental influences is
Only use a car shampoo for stubborn dirt.
frequent washing.
Wash out the sponge or washing glove thoroughly at short intervals.
How often the vehicle should be washed depends on factors such as:
› Frequency of use. Clean wheels, door sills and similar parts last. Use a second sponge for such
› Parking situation (garage, under trees etc.). areas.
› Season. Give the vehicle a good rinse after washing it and dry it off using a chamois leath-
› Weather conditions. er.
› Environmental influences.
The longer insect residues, bird droppings, tree sap, road and industrial dust, tar, CAUTION
soot particles, road salt and other aggressive deposits remain adhering to the
paintwork of your vehicle, the more detrimental their destructive effect can be. ■ When washing the car by hand, protect your hands and arms from sharp-edged
High temperatures, such as those caused by intensive sun's rays, accentuate this metal parts (e.g. when cleaning the underfloor, the inside of the wheel housings
caustic effect. or the wheel trims, etc.). – risk of cuts!
■ Only apply slight pressure when cleaning the vehicle's paintwork. 
It is essential to also thoroughly clean the underside of the vehicle at the end of
the winter.
Automatic car wash systems
WARNING
■ When washing your vehicle in the winter: Water and ice in the braking sys-
tem can affect the braking efficiency – risk of accident!
 First read and observe the introductory information and safety warn-
ings on page 105.
■ Only wash the vehicle when the ignition is switched off – risk of accident! The usual precautionary measures must be taken before washing the vehicle in
an automatic car wash system (e.g. closing the windows and the sliding/tilting
roof etc.). 

Taking care of and cleaning the vehicle 105

If your vehicle is fitted with any particular attached parts, such as a spoiler, roof
rack system, two-way radio aerial etc., it is best to consult the operator of the car Taking care of your vehicle exterior
wash system beforehand.
After an automatic wash with wax treatment, the lips of the wipers should be  Introduction
cleaned with cleaning agents specially designed for the purpose, and then de-
greased.  This chapter contains information on the following subjects:
Taking care of your vehicle's paintwork 107
Plastic parts 107
Washing with a high-pressure cleaner Rubber seals 107
Chrome parts 108
 First read and observe the introductory information and safety warn-
ings on page 105. Decorative films
Windows and exterior mirrors
108
108
When washing the vehicle with a high-pressure cleaner, the instructions for use Headlight lenses 108
of the equipment must be observed. This applies in particular to the pressure Door lock cylinders 109
used and to the spraying distance. Cavity protection 109
Maintain a sufficiently large distance to the parking aid sensors and soft materials Wheels 109
such as rubber hoses or insulation material. Underbody protection 109
Regular and proper care help to retain the efficiency and value of your vehicle. It
WARNING
may also be one of the requirements for the acceptance of warranty claims relat-
Never use circular spray nozzles or dirt cutters! ing to corrosion damage and paint defects on the bodywork.
We recommend using vehicle care products from ŠKODA Original Accessories.
CAUTION These are available from ŠKODA Partners. The usage instructions on the package
must be observed.
■ If washing the vehicle in the winter using a hose or high-pressure cleaner, en-
sure that the jet of water is not aimed directly at the locking cylinders or the WARNING
door/panel joints – risk of freezing!
■ To avoid damaging the parking aid sensors while cleaning with high-pressure ■ Vehicle care products may be harmful to your health if not used according to
cleaners or steam jets, the sensors must only be directly sprayed for short periods the instructions.
while a minimum distance of 10 cm must be observed. ■ Always store vehicle care products safely, in particular out of the reach of
■ The temperature of the water used for cleaning must not exceed 60 °C – risk of children – risk of poisoning!
damaging the vehicle. ■ Protect your hands and arms from sharp-edged metal parts when cleaning
■ See also Washing cars with decorative films using a high-pressure clean- the underfloor, the inside of the wheel housings or the wheel trims – risk of
er » page 108 .  cuts!

CAUTION
■ Do not use any insect sponges, rough kitchen sponges or similar cleaning prod-
ucts – risk of damaging the paintwork surface.
■ Cleaner that contain solvents can damage the material being cleaned. 

106 General Maintenance

 For the sake of the environment CAUTION
Used vehicle care product cans represent hazardous waste that is harmful to the ■ Never apply wax to the windows.
environment. These must be disposed of in accordance with national legal regula- ■ Mat painted or plastic parts must not be treated with polishing products or hard
tions. waxes.
■ Do not polish the paintwork in a dusty environment - risk of paint scratches.
Note ■ Do not apply any paint care products to door seals or window guides.
■ If possible, do not apply any paint care products to parts of the bodywork that
Due to the special tools and knowledge required, and to avoid any potential prob- come into contact with door seals or window guides. 
lems with the cleaning and care of the interior of your vehicle, we recommend
that cleaning and care of the interior of your vehicle be carried out by a ŠKODA
service partner. 
Plastic parts

Taking care of your vehicle's paintwork  First read and observe the introductory information and safety warn-
ings on page 106.

 First read and observe the introductory information and safety warn-
ings on page 106.
Clean plastic parts with a damp cloth.
If this method does not completely clean the plastic parts, use cleaning products
Minor paint damage such as scratches, scuffs or stone chips should be treated im- specially designed for this purpose.
mediately if possible, using touch-up pens or sprays.
CAUTION
Preserving the vehicle paintwork
A thorough wax treatment provides the vehicle's paintwork with highly effective Do not use paint care products on plastic parts. 

protection against harmful environmental influences.

The vehicle must be treated with a high-quality hard wax polish at the latest, Rubber seals
when no more drops form on the clean paintwork.
A new layer of a high-quality hard wax polish can be applied to the clean body-
work after it has dried thoroughly.  First read and observe the introductory information and safety warn-
ings on page 106.
Even if you use a wax preserver regularly we still recommend that you treat the All door seals and window guides are factory-treated with a colourless matt var-
paintwork of the vehicle at least twice a year with hard wax. nish layer to prevent the freezing of painted body parts and to protect against
Polishing driving noise.
Polishing is necessary if the vehicle's paintwork has become unattractive and if it Do not treat the door seals and window guides with any products.
is no longer possible to achieve a gloss with wax preservatives.
If the polish does not contain any preserving elements, the paint must be treated CAUTION
with a preservative afterwards. Applying additional treatments to the seals can corrode the protective coating,
and driving noise may occur. 

Taking care of and cleaning the vehicle 107

 Chrome parts Windows and exterior mirrors

 First read and observe the introductory information and safety warn-
ings on page 106.  First read and observe the introductory information and safety warn-
ings on page 106.

First clean the chrome parts with a damp cloth and then polish them with a soft, Use a plastic ice scraper for removing snow and ice from the windows and mir-
dry cloth. rors.
If this method does not completely clean chrome parts, use a specific chrome care Regularly clean windows from the inside with clean water.
product.
Dry the glass surfaces with a designated cloth or window leather.

CAUTION When drying the windows after washing the vehicle, do not use window leathers
that have been used to polish the bodywork. Residues of preservatives in the
Do not polish the chrome parts in a dusty environment - risk of surface scratches.  window leather can make the window dirty and reduce visibility.

CAUTION
Decorative films
■ The ice scraper should not be moved forward and backward but in one direction

 First read and observe the introductory information and safety warn-
ings on page 106.
to avoid any damage to the surface of the glass.
■ Snow or ice that is contaminated with coarse dirt such as fine gravel, sand or
salt must not be removed from the windows and mirrors – risk of damage to the
Wash the films with a mild soap solution and clean, warm water. Never use harsh surface of the windows and mirrors.
cleaning products or chemical solvents, as this could damage the films. ■ Do not remove snow or ice from glass parts using warm or hot water – risk of
The following instructions must be followed when washing the vehicle with a cracks forming in the glass.
high-pressure cleaner: ■ When removing snow or ice from windows and mirror lenses ensure that the

› The minimum distance between the nozzle and the vehicle body should be 50 paintwork of the vehicle is not to damage.
■ Do not clean the inside of the rear window with sharp-edged objects or corro-
cm.
› Keep jet perpendicular to the film surface. sive and acidic cleaning agents – risk of damaging the heating elements or win-
› The maximum water temperature is 50 °C. dow aerial. 

› The maximum water pressure is 80 bar.

CAUTION Headlight lenses

In the winter months, do not use an ice scraper to remove ice and snow from the
areas with films. Do not use any other objects to remove frozen layers of snow or
ice – risk of film damage. 
 First read and observe the introductory information and safety warn-
ings on page 106.

Clean plastic front headlight lenses using clean, warm water and soap. 

108 General Maintenance

 CAUTION Wheels
Never wipe headlights to dry.

■
First read and observe the introductory information and safety warn-
■ Do not use any sharp objects to clean the plastic lenses, as this may damage ings on page 106.
the protective paintwork and consequently cause cracks to form on the headlight
lenses. Wheel rims
■ Do not use any harsh cleaning products or chemical solvents to clean the head- Also thoroughly wash the wheel rims when washing the vehicle on a regular ba-
lights, as this could damage the headlight lenses. 
sis.
Regularly remove salt and brake abrasion, otherwise the rim material will be cor-
Door lock cylinders roded.
Damage to the paint layer on the wheel rims must be touched up immediately.

 First read and observe the introductory information and safety warn-
ings on page 106. Light alloy wheels
After washing thoroughly and treat the wheel rims with a protective product for
Specific products must be used for de-icing door lock cylinders. light alloy wheels. Products which cause abrasion must not be used to treat the
wheel rims.
CAUTION
CAUTION
When washing your vehicle, ensure as little water as possible gets into the lock-
ing cylinders.  Severe layers of dirt on the wheels can also result in wheel imbalance. This may
show itself in the form of a wheel vibration which is transmitted to the steering
wheel which, in certain circumstances, can cause premature wear of the steering.
Cavity protection This means it is necessary to remove the dirt. 

 First read and observe the introductory information and safety warn-
ings on page 106. Underbody protection
All corrosive cavities of the vehicle are permanently protected against chemical
and mechanical influences by protective wax.
This wax protection does not need to be inspected or re-applied.
 First read and observe the introductory information and safety warn-
ings on page 106.

The underside of your vehicle is protected for life against chemical and mechani-
If any small amount of wax flow out of the cavities at high temperatures, these cal influences.
must be removed with a plastic scraper and the stains cleaned using a petroleum
When driving, it cannot be guaranteed that no damage to the protective layer will
cleaner.
occur.
WARNING We recommend having the protective layer underneath the vehicle and the chas-
sis checked — preferably before the beginning of winter and at the end of winter. 
Safety regulations should be observed when using petroleum cleaner to re-
move wax – risk of fire! 

Taking care of and cleaning the vehicle 109

 ■ Do not clean the roof panelling with a brush – risk of damage to the surface of
WARNING
the panelling.
Never use additional underbody protection or anti-corrosion agents for ex- ■ Air fresheners and scents can be hazardous to heath when the temperature in-
haust pipes, catalytic converters or heat shields. When the engine reaches its side the vehicle is high.
operating temperature, these substances may ignite - risk of fire!  ■ Cleaner that contain solvents can damage the material being cleaned.
■ Apply only a small amount of the cleaning and care product.

For the sake of the environment

Taking care of the interior
Used vehicle care product cans represent hazardous waste that is harmful to the
environment. These must be disposed of in accordance with national legal regula-
 Introduction tions.
This chapter contains information on the following subjects:
Note
Natural leather 110
Artificial leather and fabric 111 Due to the special tools and knowledge required, and to avoid any potential prob-
lems with the cleaning and care of the interior of your vehicle, we recommend
Seat covers 111
that cleaning and care of the interior of your vehicle be carried out by a ŠKODA
Seat belts 112
service partner. 

Regular and proper care helps to ensure efficiency and maintain the value of your
vehicle.
Natural leather
We recommend using vehicle care products from ŠKODA Original Accessories.
These are available from ŠKODA Partners. The usage instructions on the package
must be observed.  First read and observe the introductory information and safety warn-
ings on page 110.

WARNING Leather is a natural material with specific properties, and requires regular clean-
ing and maintenance.
■ Vehicle care products may be harmful to your health if not used according to
the instructions. The leather should be cleaned on a regular basis depending on the amount of
■ Always store vehicle care products safely, in particular out of the reach of wear-and-tear.
children – risk of poisoning! Dust and dirt in the pores and folds act as abrasive materials. This leads to severe
corrosion and the premature brittleness of the leather surface.
CAUTION We recommend that you remove dust regularly and at short intervals using a
cloth or vacuum cleaner.
■ Be sure to check clothing for colourfastness to avoid any damage or visible
stains on the material (leather), panels and textiles. Clean soiled leather surfaces with a water-dampened cotton or woollen cloth and
■ Remove fresh stains such as those from ball-point pens, ink, lipstick, shoe pol- then dry with a clean, dry cloth » .
ish, etc., from the material (leather), panels and textiles as quickly as possible. Clean severely soiled areas with a cloth soaked in a mild soap solution (2 table-
■ Do not attach scents or air fresheners to the dash panel – risk of damage to the
spoons of neutral soap to 1 litre of water).
dash panel.
■ Do not stick any stickers on the inside of the rear window in the vicinity of the To remove stains, use a cleaning agent specially designed for this purpose. 
heating elements or the window aerial. These may get damaged.

110 General Maintenance

Treat the leather regularly and at suitable intervals using a suitable leather care Fabric
product. Clean upholstery cover materials and cloth trims on doors, luggage compartment
cover, etc. using specific cleaning agents, e.g., dry foam.
CAUTION Use a soft sponge, brush, or commercially available microfibre cloth.
■ Ensure that no part of the leather is soaked through during cleaning and that Use a cloth and a specific cleaning agent to clean the roof trim.
no water gets into the seams. Otherwise, the leather could become brittle or
cracked. Remove any lumps on the cover fabric and any fabric residue using a brush.
■ Avoid leaving the vehicle for lengthy periods in bright sunlight to avoid the Remove stubborn hair using a “cleaning glove”.
leather from bleaching. If the vehicle is parked in the open for lengthy periods,
protect the leather from direct sunlight by covering it. CAUTION
■ Sharp-edged objects on items of clothing such as zip fasteners, rivets, sharp-
edged belts, jewellery and pendants may leave permanent scratches or signs of ■ Avoid leaving the vehicle in bright sunlight for long periods of time in order to
rubbing on the surface. Such damage cannot be subsequently recognised as a stop the fabric from bleaching. If the vehicle is parked outside for long periods of
justified complaint. time, cover the fabric to protect it from direct sunlight.
■ The use of a mechanical steering wheel lock may damage the leather surface of ■ Some clothing materials, e.g. dark denim, do not have sufficient colour fastness.
the steering wheel. This can cause damage or clearly visible discolouration to seat covers, even when
■ Use a care cream with light blocker and impregnation effect on a regular basis used correctly. This applies particularly to light-coloured seat covers. This does
and each time after cleaning. The cream nourishes the leather, allows it to not relate to a fault in the seat cover, but rather to poor colour fastness of the
breathe and keeps it supple and also provides moisture. It also creates surface clothing textiles. 

protection.
■ Some clothing materials, e.g. dark denim, do not have sufficient colour fastness.
This can cause damage or clearly visible discolouration to seat covers, even when Seat covers
used correctly. This applies particularly to light-coloured seat covers. This does
not relate to a fault in the seat cover, but rather to poor colour fastness of the
clothing textiles.  First read and observe the introductory information and safety warn-
ings on page 110.

Electrically heated seats

Note Do not clean the covers by moistening, as this can damage the seat heating sys-
When using the vehicle, minor visible changes may occur to the leather parts of tem.
the covers (e.g. wrinkles or creases) as a result of the stress applied to the covers. 
Use a specific cleaning agent such as dry foam or similar to clean the covers.
Seats without seat heating
Artificial leather and fabric Thoroughly vacuum the seat covers with a vacuum cleaner before cleaning.
Clean the seat covers with a damp cloth or cleaning products specially designed
 First read and observe the introductory information and safety warn-
ings on page 110.
for this purpose.
Indented points arising on the fabrics by everyday use, can be removed by brush-
Artificial leather ing against the direction of hair with a damp brush.
Clean artificial leather with a damp cloth.
Always clean all parts of the covers, so that there are no visible edges. Then allow
If this method does not completely clean the artificial leather, use a mild soap sol- the seat to dry completely. 
ution or cleaning products specially designed for this purpose.

Taking care of and cleaning the vehicle 111

 Airbags 113
CAUTION
Trailer operation 114
■ Regularly remove dust from the seat covers using a vacuum cleaner.
■ Electrically heated seats must not be dried after cleaning by switching on the The instructions and guidelines from ŠKODA AUTO a.s. must be observed when
heater. carrying out all modifications, repairs or technical alterations to your vehicle.
■ Do not sit on wet seats - risk of seat deformation. Adhering to these instructions and guidelines helps ensure road safety and helps
■ Always clean the seats “from seam to seam”.  keep your vehicle in a good technical condition. After carrying out modifications,
repairs or technical alterations, the vehicle will comply with German road trans-
port regulations (StVZO)
Seat belts
Always consult a ŠKODA Partner » page 113 before buying accessories or parts,
or before carrying out any modifications, repairs or technical alterations to your
 First read and observe the introductory information and safety warn-
ings on page 110. vehicle.

The belt webbing must always be kept clean. WARNING

Wash dirty seat belts with mild soapy water. ■ If work on your vehicle is not carried out properly, this can lead to operation-
Remove coarse dirt with a soft brush. al faults - risk of accident and serious injuries.
■ We recommend only having these modifications and technical alterations
Dirty belt webbing may impair the correct functioning of the inertia reel. carried out by a specialist garage.
■ Interference on the electronic components and their software can lead to
WARNING operational faults. This interference can also impair not directly affected sys-
tems because of the networking of the electronic components. The operation-
■ The seat belts must not be removed for cleaning. al safety of the vehicle may be at significant risk and can lead to increased
■ Never clean the seat belts chemically as chemical cleaning products could wear of parts.
destroy the fabric. ■ The ŠKODA Partner does not assume any liability for products that have not
■ The seat belts must not be allowed to come into contact with corrosive liq-
been approved by ŠKODA AUTO a.s. even though these may be products with
uids (e.g. acids). an operational approval or that have been approved by a government testing
■ Check the condition of all the seat belts on a regular basis. If any damage to
institute.
the belt webbing, seat belt connections, inertia reel or lock is detected, the
seat belt must be replaced by a specialist garage.
■ The seat belts must be fully dried before being rolled up.  WARNING
■ We recommend that you only use ŠKODA Original Accessories and ŠKODA
Original Parts on your vehicle. This will guarantee reliability, safety and suita-
Modifications, repairs and technical alterations bility for your vehicle.
■ ŠKODA Original Accessories and ŠKODA Original Parts can be purchased
from ŠKODA Partners, who will also perform the professional assembly of the
 Introduction purchased parts. 

This chapter contains information on the following subjects:

ŠKODA Service Partners 113
Spoiler 113

112 General Maintenance

 For the sake of the environment Spoiler
Technical documents regarding alterations carried out on the vehicle must be
kept by the vehicle user in order to be handed over to the recyclers at a later
date. This ensures that the vehicle is recycled in an environmentally sound man-
 First read and observe the introductory information and safety warn-
ings on page 112.
ner. If your new vehicle is fitted with a spoiler on the front bumper in combination
with the spoiler on the luggage compartment lid, the following instructions must
Note be adhered to.
Any damage caused by technical alterations made without the approval of the
› For safety reasons, the vehicle must only be fitted with a spoiler on the front
bumper in combination with the associated spoiler on the luggage compart-
manufacturer is excluded from the warranty » See Service schedule. 
ment lid.
› This kind of spoiler cannot be left on the front bumper either on its own, in
combination with another spoiler not on the luggage compartment lid or in
ŠKODA Service Partners combination with an unsuitable spoiler on the luggage compartment lid.
› We recommend that you consult the ŠKODA service partner for any repairs to or
 First read and observe the introductory information and safety warn-
ings on page 112.
replacement, addition or removal of spoilers.

The ŠKODA Service Partners feature modern, specially developed tools and WARNING
equipment. Here, trained specialists have access to a comprehensive range of
If work on your vehicle's spoilers is not carried out properly, this can lead to
ŠKODA Original Parts and ŠKODA Original Accessories for carrying out modifica-
operational faults - risk of accident and serious injuries. 
tions, repairs and technical alterations.
All ŠKODA service partners operate according to the most recent guidelines and
instructions from ŠKODA AUTO a.s. All service and repair work is therefore carried
Airbags
out on time and at the appropriate quality. Adhering to these instructions and
guidelines helps ensure road safety and helps keep your vehicle in a good techni-
cal condition.
ŠKODA Service Partners are therefore properly prepared to service your vehicle
 First read and observe the introductory information and safety warn-
ings on page 112.

and to provide quality work. We therefore advise you to have all modifications, re- The system components of the airbag system can be situated in the front bump-
pairs and technical alterations to your vehicle carried out by a Škoda Service Part- er, doors, front seats, roof lining or body.
ner. 
WARNING
Any work on the airbag system including the installation and removal of sys-
tem components due to other repair work (e.g. removal of the steering
wheel) must only be carried out by a specialist garage.
■ Modifications, repairs and technical alterations that have been carried out
unprofessionally can cause damage and operational faults, and can also seri-
ously impair the effectiveness of the airbag system – risk of accident and fatal
injury!
■ The airbag system will then have to be replaced if the airbag is deployed.
Airbag modules cannot be repaired. 

Taking care of and cleaning the vehicle 113

 WARNING Trailer operation
Observe the following instructions for handling the airbag system.
■ It is prohibited to manipulate individual parts of the airbag system, as this
might result in the airbag being deployed.
 First read and observe the introductory information and safety warn-
ings on page 112.
■ Never install any airbag parts into the vehicle that have been removed from The vehicle is not approved for towing a trailer. The vehicle is not factory-equip-
old cars or have been recycled. ped with a towing device and it cannot be retrofitted with a towing device.
■ Never install damaged airbag parts in the vehicle. The airbags may then not
be deployed properly or even at all in the event of an accident. WARNING
■ No modifications of any kind must be made to parts of the airbag system.
Never attach a towing device to the vehicle. 

WARNING
■ A change to the vehicle's wheel suspension, including the use of non-ap-
proved wheels and tire combinations, can alter the functioning of the airbag
system - risk of accident and fatal injury!
■ Never make any changes to the front bumper or the bodywork.

WARNING
The airbag control unit operates using pressure sensors located in the front
doors. For this reason, no adjustments may be carried out to the doors or door
panels (e.g. installation of additional loudspeakers). Resulting damage can
have a negative impact on the function of the airbag system. Any work on the
front doors and door panels must be carried out by a specialist garage. The
following instructions must be observed.
■ Never drive with inner door panels removed.
■ Never drive if parts of the inner door panel have been removed and the re-
sulting openings have not been properly sealed.
■ Never drive if the loudspeakers in the doors have been removed, unless the
loudspeaker openings have been properly sealed.
■ Always make sure that the openings are covered or filled if additional loud-
speakers or other equipment parts have been installed in the inner door pan-
els. 

114 General Maintenance

 Refuelling
Inspecting and replenishing
Fig. 99
Fuel Filler flap with tank cap screwed
on
 Introduction
This chapter contains information on the following subjects:
Refuelling 115
Unleaded petrol 116
Vehicles running on CNG (compressed natural gas) » page 116.
The correct grades of fuel for your vehicle are listed on a sticker affixed to the in-
side of the fuel filler flap » Fig. 99 on page 115.
 First read and observe the introductory information and safety warn-
ings on page 115.

Open fuel filler flap

WARNING › Open the fuel filler flap with one hand » Fig. 99.
› Hold the fuel filler cap on the fuel filler tube with one hand and unlock it by
The national legal requirements must be observed if carrying a spare canister moving it to the left with the vehicle key.
in the vehicle. We do not recommend carrying any fuel canisters in your vehi- › Unscrew the filler cap by turning it to the left and place the cap onto the top of
cle for safety reasons. in the event of an accident, these canisters can become the fuel filler flap » Fig. 99.
damaged and fuel may escape – risk of fire!
Closing the filler cap
› Turn the filler cap to the right until it clicks into place.
CAUTION › Hold the fuel filler cap on the fuel filler tube with one hand and lock it by turn-
ing the vehicle key to the right and remove the key.
Never drive until the fuel tank is completely empty! The irregular supply of fuel
■
can cause misfiring, which can result in considerable damage to parts of the en-
› Close the filler cap.
gine and the exhaust system. CAUTION
■ Immediately remove any fuel that has spilled onto the vehicle's paintwork – risk
of paint damage!  The fuel tank is full just as soon as the pump nozzle switches off for the first
time, provided the nozzle has been operated properly. Do not continue filling the
fuel tank otherwise the expansion volume is filled up.

Note
The fuel tank has a capacity of about 35 litres, containing a reserve of approx.
4 litres. 

Inspecting and replenishing 115

 Fuel additives
Unleaded petrol Only use unleaded petrol, which complies with the standard EN 228 (in Germany:
standard DIN 51626-1 or E10 for unleaded fuel with an octane rating of 95 RON
 First read and observe the introductory information and safety warn-
ings on page 115.
and 91 RON or DIN 51626-2 or E5 for unleaded fuel with an octane rating of
95 RON and 98 RON), as these meet all of the requirements for fault-free engine
Your vehicle can only be operated with unleaded fuel that complies with the operation. We therefore recommend that no fuel additives are used.
standard EN 228 (in Germany: standard DIN 51626-1 or E10 for unleaded fuel with
an octane rating of 95 RON and 91 RON or DIN 51626-2 or E5 for unleaded fuel CAUTION
with the octane rating 95 RON and 98 RON).
■ All ŠKODA vehicles with petrol engines must only be operated with unleaded
Prescribed fuel – unleaded fuel 95/91 RON petrol. Just filling the tank with leaded petrol once will damage the exhaust sys-
Use unleaded fuel with the octane rating 95 RON. Unleaded petrol 91 RON can al- tem!
so be used but results in a slight loss in performance. ■ If, in an emergency, the vehicle has to be refuelled with petrol of a lower octane
number than the one prescribed, the journey must only be continued at medium
Prescribed fuel – unleaded petrol min. 95 RON engine speeds and a low engine load. Driving at high engine revs or a high engine
Use unleaded fuel with the octane rating 95 RON. load can severely damage the engine! Refuel using petrol of the prescribed oc-
In case of necessity, you can refuel with petrol with the octane rating 91 RON if tane number as soon as possible.
petrol with the octane rating 95 RON is not available. ■ Engine parts can be damaged if petrol with a lower octane number than the one
prescribed is used.
Even in the event of an emergency, petrol of a lower octane number than 91 RON ■ In no case may fuel additives with metal components be used, especially not
must not be used, otherwise the engine can be severely damaged! with manganese and iron content. Do not use any LRP (lead replacement petrol)
Unleaded petrol with higher octane number fuels with metal parts – risk of serious damage to parts of the engine or the ex-
Unleaded petrol that has a higher octane number than that required by the en- haust system!
gine can be used without limitations. ■ Do not use any fuels with metal parts – risk of serious damage to parts of the
engine or the exhaust system!
On vehicles with prescribed unleaded petrol 95/91 RON, the use of petrol with a ■ The use of unsuitable fuel additives can cause considerable damage to parts of
higher octane number than 95 RON does not result in a noticeable power in- the engine or the exhaust system. 
crease or a lower fuel consumption.
On vehicles using prescribed unleaded petrol of min. 95 RON, the use of petrol
with a higher octane number than 95 RON can increase the power and reduce Vehicles with CNG (compressed natural gas) mode
fuel consumption.
Prescribed fuel – unleaded petrol 98/(95) RON  Introduction
Use unleaded fuel with the octane rating 98 RON. Unleaded petrol 95 RON can
also be used but results in a slight loss in performance. This chapter contains information on the following subjects:
In case of necessity, you can refuel with petrol with the octane rating91 RON of Refuelling 117
unleaded fuel with octane rating 98 RON or 95 RON is not available. Automatic switching from CNG to petrol mode 118
Even in the event of an emergency, petrol of a lower octane number than 91 RON Natural gas as fuel 118
must not be used, otherwise the engine can be severely damaged! Regular gas system checks 118
Safe natural gas 119
Natural gas quality and consumption 119
CNG labels 119 

116 General Maintenance

 WARNING Refuelling
■ When operating a CNG-powered vehicle, the national legal requirements
must be observed. Fig. 100
■ If a fault occurs or a leak in the natural gas system is suspected or if you Fuel filler
smell gas, proceed as follows:
■ Stop immediately and switch off the ignition (this will close the solenoid
valves on the natural gas tanks automatically);
■ Open the doors to ventilate the vehicle sufficiently;
■ Immediately extinguish cigarettes, and remove and switch off other spark-
or fire-causing objects from the vehicle immediately.
■ Seek help from a specialist garage to correct the gas system fault.
■ The following is considered faults on the gas system:
■ Gas leakage from any part of the gas system as well as an error on the
ventilation system.
■ Continuous gas venting through the safety valves.
 First read and observe the introductory information and safety warn-
ings on page 116.

■ Cracks or damage that could result in a gas leak. The gas filler tube for refuelling with natural gas is located behind the fuel filler
■ Fault in the reduction device, the pressure regulator, gas mixer or in the flap next to the petrol filler tube.
injection valves, the pressure gauge, the shut-off or check valves and tank The filling couplings of the natural gas refuelling systems may differ in handling.
fixtures. When refuelling with natural gas at unfamiliar refuelling systems, you should
■ If gas flows into the gas mixer or into the injection valves though the en-
seek help from trained fuel station staff. If unsure, have the refuelling done by
gine is stopped. trained fuel station staff.
■ Exceeding the permissible limits for contaminants in the exhaust gas.
■ Regular gas system checks must be carried out in order to operate a natural The operating instructions of the refuelling system must always be followed.
gas vehicle. The vehicle owner is responsible for properly conducted tests.
Open fuel filler flap
■ The natural gas tanks must not be exposed to a heat source.
■ Always switch off the ignition in case of an accident or vehicle fire!
› Open the fuel filler flap with one hand.
■ It is prohibited to drive into automatic car washes, enclosed storage places,
› Remove the cap 1 » Fig. 100 from the gas filler tube 2 .
garages and similar areas where it is specifically forbidden to enter with CNG
› Plug the filling coupling of the refuelling system on the gas filler tube 2 .
vehicles.  The fuel tank is full when the compressor of the refuelling system automatically
switches off. To stop the refuelling operation prematurely, press the “Stop ” but-
ton of the refuelling system.
Closing the filler cap
› Check that the sealing ring 3 » Fig. 100 has remained in the gas filler tube. If it
has slipped onto the filling coupling, reinsert it into the gas filler tube.
› Plug the cap 1 onto the gas filler tube.
› Close the filler cap. 

Inspecting and replenishing 117

In the following situation, it is possible that the tank cannot be fully filled with
natural gas.
Automatic switching from CNG to petrol mode
› At very high ambient temperatures. The natural gas refuelling systems have
overheating protection. When the ambient temperature reaches a predefined
value, the refuelling system automatically switches off.
 First read and observe the introductory information and safety warn-
ings on page 116.
› If the refuelling system has been in operation for a longer period, the filling The vehicle automatically switches over from CNG mode to petrol mode when the
pressure of the natural gas refuelling system slightly drops. following conditions are met:
› when starting the engine, if the coolant temperature is below 15 °C,
WARNING › when the natural gas tank is empty,
■ Stop the engine before refuelling.
› after refuelling with natural gas. 

■ Always switch off your mobile phone, do not smoke and do not use open
flames when refuelling with natural gas – risk of explosion!
■ When refuelling, never get into the vehicle. If you have to get into your vehi-
Natural gas as fuel
cle in exceptional cases, close the door and touch a metal surface before you
touch the filling coupling again. This will avoid electrostatic discharges, which
may generate sparks. Sparks can cause a fire during refuelling.
 First read and observe the introductory information and safety warn-
ings on page 116.
■ Natural gas is highly explosive and flammable. Incorrect refuelling or improp- Natural gas is an alternative fuel for motor vehicles. Its main component is meth-
er handling of natural gas can cause a fire, an explosion and injuries. ane (CH4). The rest is carbon dioxide and lower hydrocarbons.
The strict legal requirements for exhaust emissions of motor vehicles are decisive
Note for the current significance of natural gas. In direct comparison to all other fossil
fuels, natural gas is one of the fuels which cause the lowest emissions.
■ The natural gas system of your vehicle is suitable both for fuelling from small
compressors (slow fuelling) and for fuelling from natural gas stations with large Natural gas is odourless and lighter than air. For safety reasons, it is saturated
compressors (quick fuelling). with odorous substances, so that is perceived even in very small amounts. 

■ Noises that occur during refuelling represent no risk.

■ If the vehicle is parked for a longer period of time immediately after refuelling,
the situation may arise in which the pointer of the fuel tank gauge does not indi- Regular gas system checks
cate exactly the same level as was the case immediately after refuelling when the
engine is restarted. This is not due to any system leakages but a drop in pressure
in the natural gas fuel tank due to technical reasons after a cooling phase directly
after refuelling.
 First read and observe the introductory information and safety warn-
ings on page 116.

■ For frequent short-haul traffic, especially at low outside temperatures, the vehi-
Every two years, the following inspections must be carried out:
cle is driven more frequently in petrol mode than in natural gas mode. This is why › Check the condition of the fuel filler cap, filler neck and sealing ring, and clean
sealing ring if necessary.
the petrol tank runs empty faster than the natural gas tank.
■ The capacity of the natural gas tank is about 11 kg, of which about 1.5 kg are a › Check gas system for leaks.
reserve. The following checks must be carried out every four years:
■ The capacity of the petrol tank is about 10 l, of which about 5 l are a reserve.  › Check gas tank mounting for secure attachment and possible damage.
The gas tank must be filled prior to the regular gas system check. 

118 General Maintenance

 Safe natural gas CNG labels

 First read and observe the introductory information and safety warn-
ings on page 116.

The safety concept of the natural gas system ensures safe operation. It is equip-
ped with the following security features.
› At each natural gas tank, there is a solenoid valve that closes automatically af-
ter turning off the ignition or when running in petrol mode.
› A thermal fuse prevents uncontrolled rise in pressure in the natural gas tank in
case of fire.
› A flow limiter prevents sudden emptying of the natural gas tank in case the
pressure system is damaged.
› All the attachment points and materials are designed for maximum safety.  Fig. 101 CNG label

Natural gas quality and consumption Fig. 102

Position of the CNG label

 First read and observe the introductory information and safety warn-
ings on page 116.

Natural gas is divided into quality groups H-gas and L-gas. The two types of gas
are subdivided according to their calorific value and nitrogen and carbon dioxide
contents. H-gas has a higher calorific value and lower nitrogen or carbon dioxide
content than L-gas.
The higher the calorific value of natural gas, the lower is the consumption. How-
ever, the calorific value and the nitrogen and carbon dioxide contents can vary
within a quality group. Therefore, the consumption of the vehicle may even vary
when driving with only one natural gas quality (either only H-gas or L-gas).
 First read and observe the introductory information and safety warn-
ings on page 116.

In some countries, national legislation requires that vehicles with CNG operation
The engine control of your vehicle automatically adjusts to the different natural
be identified by one of the listed labels » Fig. 101.
gas qualities. Therefore both natural gas qualities can be mixed in the fuel tank. It
is therefore not necessary to run the natural gas tank completely empty to fill up Position of the CNG label » Fig. 102. 
another quality. 

Inspecting and replenishing 119

 WARNING (Continued)
Engine compartment
■ Do not touch any hot engine parts – risk of burns!
 Introduction ■ The coolant additive and thus all of the coolant is harmful to your health.
■ Avoid contact with the coolant.
This chapter contains information on the following subjects: ■ Coolant vapours are harmful to health.
■ Never open the end cover of the coolant expansion reservoir while the en-
Opening and closing the bonnet 121 gine is still warm. The cooling system is pressurized!
Engine compartment overview 122 ■ When opening the end cover of the coolant expansion reservoir, cover it
Radiator fan 122 with a cloth to protect your face, hands and arms from hot steam or hot cool-
Windscreen washer system 122 ant.
■ If any coolant splashes into your eyes, immediately rinse out your eyes with
WARNING clear water and contact a doctor as soon as possible.
■ Always store the coolant additive securely in its original container, and in
Injuries or scolding or risks of accident or fire may occur when working in the particular out of the reach of children – risk of poisoning!
engine compartment. For this reason, it is essential to comply with the warn- ■ If coolant is swallowed, consult a doctor immediately.
ing instructions outlined below and with the general applicable safety rules. ■ Do not leave any items such as cloths or tools in the engine compartment.
The engine compartment of your car is a hazardous area! ■ Never spill fluids on the hot engine. Such fluids (e.g. the antifreeze con-
tained in the coolant) may ignite!
WARNING
The following instructions must be followed before starting work in the en-
WARNING
gine compartment: The following warning instructions must be followed at all times when work-
■ Turn off the engine and withdraw the ignition key. ing in the engine compartment while the engine is running.
■ Firmly apply the handbrake. ■ Pay particular attention to rotating engine parts (e.g. V-ribbed belt, genera-
■ If the vehicle is fitted with a manual gearbox, move the gearshift lever into tor, radiator fan) and the high-voltage ignition system – risk to life!
Neutral, or if the vehicle is fitted with an automatic gearbox, move the selec- ■ Never touch the electric wiring on the ignition system.
tor lever into position N. ■ Avoid short circuits in the electrical system – particularly on the vehicle's
■ Allow the engine to cool. battery.
■ Never open the bonnet if you can see steam or coolant escaping from the ■ Always make sure that no jewellery, loose clothing or long hair can get
engine compartment – risk of scalding! Wait until no more steam or coolant is caught in rotating engine parts – risk to life! Always remove any jewellery, tie
escaping. back long hair and wear tight fitting clothing before completing any work.

WARNING WARNING
The following instructions must be followed when working in the engine com- The following warning instructions must be observed if work has to be carried
partment. out on the fuel or electrical systems.
■ Keep children clear of the engine compartment. ■ Always disconnect the vehicle battery from the electrical system.
■ Never touch the radiator fan while the engine is still warm. The fan might ■ Do not smoke.
suddenly start running! ■ Never work near open flames.
■ Always have a functioning fire extinguisher nearby. 

120 General Maintenance

 WARNING Opening and closing the bonnet
■ Read and observe the information and warning instructions on the fluid con-
tainers.
■ Keep fluids in their original containers and keep securely out of the reach of
children!
■ If you intend to work underneath the vehicle, you must secure the vehicle
from rolling away and support it with suitable supporting blocks; the car jack
is not sufficient – risk of injury!
■ Never cover the engine with additional insulation material (e.g. with a cover)
– risk of fire!
■ The bonnet must always be properly closed when driving. Therefore, the
lock must always be checked after closing the bonnet in order to ensure that
it has engaged properly. Fig. 103 Unlocking the bonnet
■ If you notice that the lock is not properly engaged while driving, stop the ve-
hicle immediately and close the bonnet – risk of accident!

CAUTION
■ Always top up using the correct specification of fluids. This may result in major
operating problems and also vehicle damage!
■ Never open the bonnet using the locking lever.

For the sake of the environment

In view of the requirements for the environmentally friendly disposal of fluids and
the specials tools and knowledge required for such work, we recommend that flu- Fig. 104 Securing the bonnet
ids be changed by a specialist garage as part of an inspection service.

■
Note
Please consult a specialist garage for any questions relating to fluids.
 First read and observe the introductory information and safety warn-
ings on page 120.

Opening
■ Fluids with the correct specifications can be purchased from ŠKODA Original Ac-
cessories. 
› Pull the release lever under the dash panel 1 » Fig. 103 in the direction of the
arrow.
Before opening the bonnet, ensure that the arms of the windscreen wipers are
correctly in place against the windscreen otherwise the paintwork could be dam-
aged.
› Press the release lever in the direction of the arrow 2 » Fig. 103 and the bon-
net is unlocked.
› Grab hold of the bonnet and lift. 

Inspecting and replenishing 121

› Take the bonnet support out of its holder 3 in the direction if the ar-
Radiator fan
row » Fig. 104 and secure the opened bonnet by inserting the end of the sup-
port in the opening 4 designed for it.
Closing
› Lift the bonnet slightly and unhook the bonnet support. Press the bonnet sup-
 First read and observe the introductory information and safety warn-
ings on page 120.

port into the holder 3 designed to hold it. After switching off the ignition, the fan may intermittently continue to operate for
› Let the bonnet drop into the lock carrier lock from a height of around 20 cm – do approx. 10 minutes.
not push it in. The radiator fan is powered by an electric motor. Operation is controlled accord-
› Check that the bonnet is closed properly. 
ing to the temperature of the coolant. 

Engine compartment overview Windscreen washer system

Fig. 106
Engine compartment: Wind-
screen washer fluid reservoir

 First read and observe the introductory information and safety warn-
ings on page 120.

The windscreen washer reservoir contains the cleaning fluid for the windscreen
Fig. 105 Schematic diagram: Engine compartment
or rear window. The reservoir is located in the engine compartment .

 First read and observe the introductory information and safety warn-
ings on page 120.
The capacity of the windscreen washer fluid reservoir is approximately 3 litres.
Water alone is not sufficient to intensively clean the windscreen. We recommend
1 Engine oil dipstick 124 using clean water together with a screen cleaner from the range of ŠKODA Origi-
nal Accessories (with antifreeze in winter), which will remove any stubborn dirt.
2 Engine oil filler opening 124
3 Coolant expansion reservoir 126 Under exceptional circumstances, methylated spirits can also be used if no screen
4 Brake fluid reservoir 127 cleaner with antifreeze is available. The concentration of methylated spirits must
not be more than 15 %. The freeze protection at this concentration is sufficient
5 Vehicle battery 127
only to -5 °C. 
6 Windscreen washer fluid reservoir 122 

122 General Maintenance

 CAUTION CAUTION
■ Under no circumstances must radiator antifreeze or other additives be added to Do not pour any additives into the engine oil – risk of serious damage to the en-
the windscreen washer fluid. gine parts! Damage, which results from such product, are excluded from the war-
■ Do not remove the filter from the windscreen washer fluid reservoir when refill- ranty.
ing, as this may cause contamination of the liquid transportation system, leading
in turn to a windscreen washer system malfunction. 
Note
■ Before a long drive, we recommend that you purchase and carry with you en-
gine oil that complies with the specifications for your vehicle.
Engine oil ■ We recommend that you use oils from ŠKODA Original Parts.
■ If oil comes into contact with your skin, the affected area must be washed thor-
 Introduction oughly. 

This chapter contains information on the following subjects:

Specifications and capacity 123
Specifications and capacity
Checking the oil level 124
Replenishing
Changing
124
124
 First read and observe the introductory information and safety warn-
ings on page 123.

Specifications and capacity (in l)

The engine has been factory-filled with a high-grade oil that can be use through-
out the year - except in extreme climate zones. Engine Specification Filling level

The engine oils are undergoing continuous further development. Thus the infor- 1.0 l/44 kW VW 502 00, VW 504 00a) 3.4
mation stated in this Owner's Manual is only correct at the time of publication. 1.0 l/55 kW VW 502 00, VW 504 00a) 3.4
ŠKODA Service Partners are informed about the latest changes by the manufac- 1.0 l/50 kW - CNG VW 502 00 3.4
turer. We therefore recommend that the oil change be completed by a ŠKODA a) The use of an engine oil with the VW 504 00 specification requires the use of a fuel according to the
Service Partner. EN 228 standard » page 116, Unleaded petrol or a fuel of comparable quality.

The specifications (VW standards) stated in the following can be indicated sepa-
rately or together with other specifications on the bottle. Note
The oil capacities include oil filter change. Check the oil level when filling; do not ■ Before a long drive, we recommend that you purchase and carry with you en-
over fill. The oil level must be between the markings » page 124. gine oil that complies with the specifications for your vehicle.
■ We recommend that you use oils from ŠKODA Original Parts. 

WARNING
■ The engine compartment of your car is a hazardous area. The following
warning instructions must be followed at all times when working in the en-
gine compartment » page 120.
■ Do not continue your journey if for some reason it is not possible  to top
up the engine oil under the prevailing conditions! Switch off the engine and
seek assistance from a specialist garage.

Inspecting and replenishing 123

 One should therefore check the oil level at regular intervals, preferably every time
Checking the oil level after the fuel tank is filled or after driving for long stretches.
We recommend maintaining the oil level within the range A , but not above, if
Fig. 107 the engine has been operating at high loads, for example, during a lengthy motor-
Dipstick way trip during the summer months, towing a trailer or negotiating a high moun-
tain pass.
The warning light in the instrument cluster will indicate whether the oil level is
too low » page 15,  Engine oil pressure. In this case, check the oil level with the
dipstick, as soon as possible. Add oil accordingly.

CAUTION
The oil level must on no account extend beyond the range A » Fig. 107. Risk of
 First read and observe the introductory information and safety warn-
ings on page 123.
damaging the exhaust system!

The dipstick indicates the level of oil in the engine » Fig. 107. Note
Checking the oil level Engine oil specifications » page 123. 

› Ensure that the vehicle is positioned on a level surface and the engine has
reached its operating temperature.
› Switch off the engine. Replenishing
› Open the bonnet.
› Wait a few minutes until the engine oil flows back into the oil sump and remove
the dipstick.
› Wipe the dipstick with a clean cloth and insert it again to the stop.
 First read and observe the introductory information and safety warn-
ings on page 123.

› Then pull the dipstick out again and check the oil level. › Check the engine oil level » page 124.
› Unscrew the cap of the engine oil filler opening.
Oil level within range A › Replenish the oil in portions of 0.5 litres in accordance with the correct specifi-
› No oil must be refilled. cations » page 123, Specifications and capacity.
Oil level within range B › Check the oil level » page 124.
› Oil can be refilled. It is possible that the oil level may then be within range A › Carefully screw on the oil filler opening cap and push the dipstick in fully. 

after doing this.

Oil level within range C Changing
› Oil must be refilled. It is sufficient, once this is done, to keep the oil level within
range B .
It is normal for the engine to consume oil. The oil consumption may be as much as
 First read and observe the introductory information and safety warn-
ings on page 123.

0.5 l/1 000 km depending on your style of driving and the conditions under which The engine oil must be changed at the intervals stated in the Service schedule or
you operate your vehicle. Consumption may be slightly higher than this during the according to the service interval indicator » page 10, Service Interval Display. 
first 5 000 kilometres.

124 General Maintenance

 Note CAUTION
If oil comes into contact with your skin, the affected area must be washed thor- ■ The concentration of coolant additive in the coolant must never be under 40%.
oughly.  ■ Over 60% of coolant additive in the coolant reduces the antifreeze protection
and cooling effect.
■ Other coolant additives that do not comply with the correct specifications can

Coolant significantly reduce the corrosion protection.

■ Any faults resulting from corrosion may cause a loss of coolant and can conse-
quently result in major engine damage!
 Introduction ■ Do not fill the coolant above the mark A » Fig. 108 on page 126.
■ If a fault causes the engine to overheat, we recommend visiting a specialist ga-
This chapter contains information on the following subjects: rage, as otherwise serious engine damage may occur. 

Capacity 125
Checking the coolant level 126
Capacity
Replenishing 126
The coolant consists of water with coolant additive. This mixture guarantees anti-
freeze protection, protects the cooling/heater system against corrosion and pre-
vents lime formation.
 First read and observe the introductory information and safety warn-
ings on page 125.

Coolant capacity
Vehicles exported to countries with a mild climate are already factory-filled with
Petrol engines Capacities (in litres)
a coolant which offers antifreeze protection down to about -25 ℃. In these coun-
tries, the concentration of coolant additive should be at least 40%. 1.0 ltr./44 kW MPI 4.2
Vehicles exported to countries with a cold climate are already factory-filled with a 1.0 ltr./55 kW MPI 4.2
coolant which offers antifreeze protection down to about -35 °C. In these coun- 1.0 l/50 kW - CNG 4.2 
tries, the concentration of coolant additive should be at least 50%.
If a higher concentration of antifreeze is required for climatic reasons, the con-
centration of coolant additive can be increased up to a maximum of 60% (anti-
freeze protection down to approx. -40 °C).
When refilling, we only recommend you use the same antifreeze written on the
antifreeze expansion tank » Fig. 108 on page 126.

WARNING
■ The engine compartment of your car is a hazardous area. The following
warning instructions must be followed at all times when working in the en-
gine compartment » page 120.
■ Do not continue your journey if for some reason it is not possible  to top
up the coolant under the prevailing conditions! Switch off the engine and seek
assistance from a specialist garage.

Inspecting and replenishing 125

 Checking the coolant level › Place a cloth over the cap of the coolant expansion reservoir » Fig. 108 on
page 126 and unscrew the cap carefully.
› Replenish the coolant.
Fig. 108 › Turn the cap until it clicks into place.
Engine compartment: Coolant
Do not use an alternative additive if the specified coolant is not available in an
expansion reservoir
emergency. In this case, use just water and have the correct mixing ratio of water
and coolant additive restored by a specialist garage as soon as possible.
Only use new coolant to top up the system.
Do not fill the coolant above the mark “MAX” » Fig. 108 on page 126! Excess cool-
ant heats up and then is forced out of the cooling system through the pressure
relief valve in the cap. 

 First read and observe the introductory information and safety warn-
ings on page 125.
Brake fluid
The coolant expansion bottle is located in the engine compartment.
› Switch off the engine.  Introduction
› Open the bonnet » page 121.
› Check the level of coolant in the coolant expansion bottle » Fig. 108. The cool- This chapter contains information on the following subjects:
ant level when the engine is cold must lie between the “MIN” and “MAX” mark- Checking the brake fluid level 127
ings. The level may also rise slightly above the “MAX” marking when the engine
Changing 127
is warm.
If the coolant level in the coolant expansion tank is too low, this is indicated by WARNING
the warning light  lighting up in the instrument cluster » page 16,  Coolant
■ The engine compartment of your car is a hazardous area. The following
temperature/coolant level. We still recommend inspecting the coolant level di-
warning instructions must be followed at all times when working in the en-
rectly at the reservoir from time to time.
gine compartment » page 120.
Loss of coolant ■ Do not continue your journey i the fluid level has dropped below the MIN
A loss of coolant is first and foremost an indication of a leak in the system. Do marking,  – risk of accident! Seek help from a specialist garage.
not merely top up the coolant. Have the cooling system checked by a specialist ■ Do not use used brake fluid - the function of the brake system may be im-
garage immediately.  paired – risk of accident!

Replenishing CAUTION
Brake fluid damages the paintwork of the vehicle.

 First read and observe the introductory information and safety warn-
ings on page 125.
Note
› Switch off the engine. The brake fluid is changed as part of a compulsory inspection service. 
› Allow the engine to cool.

126 General Maintenance

 Checking the brake fluid level Vehicle battery

Fig. 109  Introduction

Engine compartment: Brake fluid
reservoir This chapter contains information on the following subjects:
Checking the battery electrolyte level 129
Operation in winter 129
Charging a vehicle battery 129
Disconnecting and reconnecting the vehicle battery 130
Replacing the vehicle battery 130

 First read and observe the introductory information and safety warn-
ings on page 126.
Automatic load deactivation

Warning symbols on the vehicle battery

130

The brake fluid reservoir is located in the engine compartment. Symbol Importance
› Switch off the engine.
› Open the bonnet » page 121.  Always wear eye protection.

› Check the level of brake fluid in the reservoir » Fig. 109. The level must be be- Battery acid is severely caustic. Always wear gloves and eye protec-
tween the “MIN” and “MAX” markings.  tion.
When driving, a slight drop in the fluid level is caused by the wear-and-tear and Keep fire, sparks, open flames and lit cigarettes well clear of the ve-
automatic adjustment of the brake pads, and is therefore perfectly normal.  hicle battery.
There may be an indication of a leak in the brake system, however, if the fluid lev- When charging the vehicle battery, a highly explosive gas mixture is
el drops significantly within a short time or if it drops below the “MIN” marking. If  produced.
the brake fluid level is too low, this is indicated by the warning light  lighting up
in the instrument cluster » page 14, Braking system. 
 Keep children away from the vehicle battery.

Improper handling of the battery can lead to damage. We recommend having all
Changing work on the vehicle battery carried out by a specialist garage.

 First read and observe the introductory information and safety warn-
ings on page 126.
WARNING
There is risk of injuries, poisoning, chemical burns, explosions or fire when
Brake fluid absorbs moisture. Over time it therefore absorbs moisture from the working on the battery and on the electrical system. It is essential to comply
environment. Excessive water in the brake fluid may be the cause of corrosion in with the warning instructions outlined below and with the general applicable
the brake system. The water content also lowers the boiling point of the brake safety rules.
fluid. ■ Keep children away from the vehicle battery. 

The brake fluid must comply with the following standards or specifications:
› VW 50114;
› FMVSS 116 DOT4. 

Inspecting and replenishing 127

 WARNING (Continued) WARNING
■ Do not tilt the battery otherwise battery electrolyte may flow out of the bat- ■ When you charge a battery, hydrogen is released, and a highly explosive gas
tery vent openings. Protect your eyes by wearing safety goggles or a face mixture is also produced. An explosion can be caused through sparkling over
shield – risk of blindness! during unclamping or loosening of the cable plug while the ignition is on.
■ Always wear protective gloves, eye and skin protection when handling the ■ Creating a bridge between the poles on the battery (e.g. with a metal object
vehicle battery. or cable) creates a short circuit - risk of melting the lead bars, and risk of ex-
■ The battery acid is strongly corrosive and must, therefore, be handled with plosion, battery fire and acid splashes.
the greatest of care. ■ Avoid creating sparks when working with cables and electrical devices.
■ Corrosive fumes in the air irritate the air passages and lead to conjunctivitis Strong sparking represents a risk of injury.
and inflammation of the air passages in the lungs. ■ Before carrying out any work on the electrical system, switch off the engine,
■ Battery acid corrodes dental enamel and, if it comes into contact with the the ignition and all of the electrical components and disconnect the negative
skin, causes deep wounds that take a long time to heal. Repeated contact terminal ( ) on the battery.
with diluted acids causes skin diseases (inflammations, ulcers, skin cracks).
■ If any battery acid comes into contact with your eyes, rinse the affected eye
immediately with clean water for several minutes and consult a doctor imme- CAUTION
diately!
■ The vehicle battery must only be disconnected if the ignition is switched off,
■ Splashes of acid on your skin or clothes should be neutralised as soon as
otherwise the vehicle's electrical system (electronic components) can be dam-
possible using soap suds and then rinsed with plenty of water. If you swallow
aged. When disconnecting the battery from the electrical system, first disconnect
battery acid, consult a doctor immediately!
the battery's negative terminal ( ), followed by the positive terminal ( ).
■ When connecting the battery to the electrical system, first connect the battery's
WARNING positive terminal ( ), followed by the negative terminal ( ). Under no circumstan-
ces must the battery cables be connected incorrectly – risk of a cable fire.
■ It is prohibited to work with naked flames or lights. ■ Ensure that battery acid does not come into contact with the bodywork – risk of
■ It is prohibited to smoke or carry out any activities that produce sparks. damage to the paintwork.
■ Never use a damaged vehicle battery – risk of explosion! ■ Do not place the battery in direct daylight in order to protect the vehicle battery
■ Never charge a frozen or thawed vehicle battery – risk of explosion and housing from the effects of ultra-violet light.
chemical burns! ■ If the vehicle has not been driven for more than 3 to 4 weeks, the battery will
■ Replace a frozen vehicle battery. discharge. This is because certain electrical components consume electricity (e. g.
■ Never jump-start vehicle batteries with insufficient acid levels – risk of ex- control units) also in idle state. Prevent the battery from discharging by discon-
plosion and chemical burns. necting the battery's negative terminal ( ) or continuously charging the battery
with a very low charging current.
■ If the vehicle is frequently used for making short trips, the vehicle battery will
not have time to charge up sufficiently and may discharge.

For the sake of the environment

A vehicle battery that has been removed is a special type of hazardous waste.
These must be disposed of in accordance with national legal regulations. 

128 General Maintenance

 Note Note
You should replace batteries older than 5 years.  ■ The battery acid level is also checked regularly by a specialist garage as part of
the inspection service.
■ For technical reasons, on vehicles with the description “AGM”, the electrolyte
Checking the battery electrolyte level level cannot be checked.
■ Vehicles with a START-STOP system are fitted with a battery control unit for
checking the energy level for the recurring engine start. 
Fig. 110
Vehicle battery: Electrolyte level
indicator
Operation in winter

 First read and observe the introductory information and safety warn-
ings on page 127.

At low temperatures, the vehicle battery only has part of the initial power output
that it has at normal temperatures.
A discharged vehicle battery may already freeze at temperatures just below 0
 First read and observe the introductory information and safety warn-
ings on page 127.
°C.
We therefore recommend that you have the battery checked by a specialist ga-
We recommend that you have the acid level checked regularly by a specialist ga- rage before the start of winter, and recharged if necessary. 
rage, especially in the following cases.
› High outside temperatures.
› Long daily drives Charging a vehicle battery
› After each charge » page 129.
On vehicles with a vehicle battery fitted with a colour indicator, the so-called
magic eye » Fig. 110, the electrolyte level can be determined by looking at the
change in colour.
 First read and observe the introductory information and safety warn-
ings on page 127.

A properly charged vehicle battery is essential for reliably starting the engine.
Air bubbles can influence the colour of the indicator. For this reason carefully
knock on the indicator before carrying out the check.
› Switch off the ignition and all of the electrical components.
› Black colour – electrolyte level is correct. › Only for “quick-charging”: Disconnect both battery cables (first of all “negative”,
then “positive”).
› Colourless or light yellow colour – electrolyte level too low, the battery must be › Attach the terminal clamps of the charger to the battery terminals (red = “posi-
replaced.
tive”, black = “negative”).
› Only now plug the mains cable of the charger into the power socket and switch
on the device.
› When charging is completed: Switch off the charger and remove the mains ca-
ble from the power socket.
› Only then disconnect the charger's terminal clamps.
› Reconnect the cables to the battery, if necessary (first of all “positive”, then
“negative”). 

Inspecting and replenishing 129

It is not normally necessary to disconnect the cables of the battery if you re-
charge the vehicle battery using low amperages (as for example from a mini-
Replacing the vehicle battery
charger). Refer to the instructions of the charger manufacturer.
A charging current of 0.1 multiple of the total vehicle battery capacity (or lower)
must be used until full charging is achieved.
 First read and observe the introductory information and safety warn-
ings on page 127.

When replacing a battery, the new vehicle battery must have the same capacity,
It is, however, necessary to disconnect both cables before charging the battery voltage, amperage and be the same size. Suitable vehicle battery types can be
with high amperages, so-called “quick-charging”. purchased from a specialist garage.
“Quick-charging” the vehicle battery is dangerous and requires a special charger We recommend having the battery replaced by a specialist garage, where the
and specialist knowledge. We therefore recommend that vehicle batteries be new vehicle battery will be installed properly and the original battery will be dis-
quick-charged by a specialist garage. posed of in accordance with national regulations. 

The vent plugs of the vehicle battery should not be opened for charging.

CAUTION Automatic load deactivation

On vehicles with the START/STOP system, the pole terminal of the charger must
not be connected directly to the negative terminal of the vehicle battery, but only
to the engine earth » page 146, Jump-starting in vehicles with the START-STOP
 First read and observe the introductory information and safety warn-
ings on page 127.

system.  The vehicle voltage control unit automatically prevents the battery from discharg-
ing when the battery is put under high levels of strain. This manifests itself by the
following:
Disconnecting and reconnecting the vehicle battery › The idling speed is raised to allow the generator to deliver more electricity to
the electrical system.
› Where necessary, large convenience consumers such as seat heaters and rear
 First read and observe the introductory information and safety warn-
ings on page 127. window heaters have their power limited or are shut off completely in the event
of an emergency.
On disconnecting and reconnecting the vehicle battery the following functions
are initially deactivated or are no longer able to operate fault-free: CAUTION
Operation Operating measure ■ Despite such intervention by the vehicle electric system management, the vehi-
Enter radio code number » Radio manual cle battery may be drained. For example, when the ignition is switched on a long
time with the engine turned off or the side or parking lights are turned on during
Setting the clock » page 12
longer parking.
Data in the multifunction display are deleted. » page 11 ■ Consumers that are supplied via a 12-V power socket can cause the vehicle bat-
tery to discharge when the ignition is switched off.
Note
We recommend having the vehicle checked by a specialist garage in order to en-
Note
sure full functionality of all electrical systems. 
Driving comfort is not impaired by consumers being deactivated. The driver is of-
ten not aware of it having taken place. 

130 General Maintenance

 WARNING (Continued)
Wheels ■ Unusual vibrations or pulling of the vehicle to one side could be a sign of
tyre damage. If there is any doubt that a wheel is damaged, immediately re-
Tyres and wheel rims duce your speed and stop! If no external damage is evident, drive slowly and
carefully to the nearest specialist garage to have the vehicle checked.
■ Only use tyres or wheel rims that have been approved by ŠKODA for your
 Introduction model of vehicle. Failure to observe this instruction may impair the road safety
of your vehicle – risk of accident!
This chapter contains information on the following subjects:
Service life of tyres 132
WARNING
New tyres 133
Unidirectional tyres 134 Observe the following information regarding tyre damage and wear.
Spare wheel 134 ■ Never use tyres if you do not know anything about the condition and age.
Full wheel trim 135 ■ Never drive with damaged tyres – risk of accident!
■ Immediately replace damaged wheel rims or tyres.
Wheel bolts 135
■ You must have your tyres replaced with new ones at the latest when the
Wheel bolts 135
wear indicators have been worn down.
■ Worn tyres impair necessary adhesion to the road surface, particularly at
WARNING
high speeds on wet roads. This could lead to “aquaplaning” (uncontrolled ve-
■The national legal regulations must be observed for the use of tyres. hicle movement – “swimming” on a wet road surface).
■Observe the national legal regulations relating to the use of snow chains
and the maximum vehicle speed with snow chains.
WARNING
Observe the following information regarding the tyre inflation pressure.
WARNING ■ The tyre control display does not absolve the driver of the responsibility to
The following instructions for the use of tyres must be observed. ensure the correct tyre inflation pressure. Check the tyre inflation pressure at
■ For the first 500 km, new tyres do not yet provide optimum grip, and appro- regular intervals.
priate care should therefore be taken when driving – risk of accident! ■ Insufficient or excessive inflation pressure impairs handling – risk of acci-
■ Only use radial tyres of the same type, size (rolling circumference) and tread dent!
pattern on all four wheels. ■ If the inflation pressure is too low, the tyre will have to overcome a higher
■ For reasons of driving safety, do not replace tyres individually. rolling resistance. This will cause a significant increase in the temperature of
■ Never exceed the maximum permissible load bearing capacity for fitted the tyre, especially at higher speeds. This can result in tread separation and a
tyres – risk of accident! tyre blowout. 
■ Never exceed the maximum permissible speed for fitted tyres – risk of acci-
dent!
■ Incorrect wheel alignment at the front or rear impairs handling – risk of acci-
dent!

Wheels 131
 WARNING Service life of tyres
Observe the following information regarding the wheel bolts.
■ The wheel bolts must be clean and must turn easily. Never apply grease or
oil.
■ The prescribed tightening torque for the wheel bolts is 110 Nm for steel and
light alloy wheel rims.
■ If the wheel bolts are tightened to an insufficient tightening torque, the
rims may come loose when the car is moving – risk of accident! A tightening
torque which is too high can damage the bolts and threads and this can result
in permanent deformation of the contact surfaces on the rim.
■ If the wheel bolts are handled incorrectly, the wheel may come loose when
the car is moving – risk of accident!
Fig. 111 Schematic diagram: Tyre tread with wear indicators/open fuel filler
flap with a table detailing the tyre sizes and tyre inflation pressures
WARNING
Observe the following information regarding the spare wheel.
■Only use the spare wheel for as long as is necessary. Fig. 112
■Never drive with more than one spare wheel attached. Replacing wheels
■The snow chains cannot be used on the spare wheel.

CAUTION
■ If a spare wheel is used that is not identical to the fitted tyres, the following
must be observed » page 134, Spare wheel.
■ Protect the tyres from contact with oil, grease and fuel.
■ Replace lost valve caps.
■ If, in the event of a puncture, it is necessary to fit a spare wheel with a tyre
without a dedicated running direction or with the opposite direction of rotation,
drive carefully as the optimal characteristics of the tyre are no longer applicable in
 First read and observe the introductory information and safety warn-
ings on page 131.

this situation. The service life of tyres depends on the inflation pressure, driving style and other
circumstances. Following the advice below can extend the service life of your
For the sake of the environment tyres.
Tyre pressure
Tyres that are insufficiently inflated increase your fuel consumption.
Check the tyre pressure, including that of the spare wheel, at least once a month
and also before setting off on a long journey.
Note
The tyre inflation pressures for tyres are indicated on the inside of the fuel filler
■ We recommend that any work on the wheels or tyres be carried out by a spe- flap » Fig. 111 – .
cialist garage.
■ We recommend that you use wheel rims, tyres, full wheel trims and snow chains The tyre pressure for the spare wheel should correspond to the highest pressure
from ŠKODA Original Accessories.  specified for your vehicle. 

132 General Maintenance

Always check the inflation pressure when the tyres are cold. Do not reduce the Tyre age
higher pressure of warm tyres. Tyres age and lose their original characteristics, even if they are not being used.
Therefore, we recommend not using summer or winter tyres older than 6 or
With greater additional load, adjust the tyre inflation pressure accordingly.
4 years old respectively. 

Driving style
Fast cornering, sharp acceleration and braking increase the wear of your tyres.
New tyres
Balancing wheels
The wheels of a new vehicle are balanced. When driving, however, there are a
range of factors that may result in an imbalance. This may become apparent by a
vibration in the steering.
 First read and observe the introductory information and safety warn-
ings on page 131.

Only use radial tyres of the same type, size (rolling circumference) and tread pat-
Have the wheels rebalanced after replacing the tyres.
tern on one axle on all four wheels.
Wheel alignment errors
The tyre/wheel combinations which are approved for your vehicle are indicated in
Incorrect wheel alignment at the front or rear leads to excess wear of the tyres.
your vehicle documents.
Tyre damage Where possible, replace tyres by axle. Always fit the tyres with the deeper tread
Drive over kerbs and other such obstacles slowly and at right angles wherever depth to the front wheels.
possible in order to avoid damage to tyres and wheel trims.
Explanation of tyre markings
We recommend checking your tyres and wheel rims for damage (punctures, cuts,
185/55 R 15 82 T
splits and bulges, etc.) on a regular basis. Remove foreign bodies (e.g. small
stones) from the tyre tread immediately. What this means is:
Replacing wheels 185 Tyre width in mm » Fig. 111 on page 132 - 
If significantly greater wear is present on the front tyres, we recommend replac- 55 Height/width ratio in % » Fig. 111 on page 132 - 
ing the front wheels with the rear wheels as shown in the diagram » Fig. 112. You
R Code letter for the type of tyre – Radial » Fig. 111 on page 132 - 
will then obtain approximately the same life for all the tyres.
15 Wheel rim diameter in inches » Fig. 111 on page 132 - 
We recommend that you swap the tyres every 10,000 km in order to achieve even
wear on all tyres and to ensure optimal service life for the tyres. 82 Load index »
T Speed symbol »
Storing tyres
Identify disassembled tyres so that the previous direction of rotation can be The date of manufacture is stated on the tyre wall (possibly on the inside). e.g.
maintained if the tyres are reassembled. DOT ... 10 13...
Always store wheels or tyres in a cool, dry place that is as dark as possible. Tyres means, for example, that the tyre was manufactured in the 10th week of 2013.
which are not fixed to a wheel trim should be stored upright.
Load index
Wear indicators
The base of the tread of the tyres has 1.6 mm high wear indicators installed. De- This indicates the maximum permissible load for each individual tyre.
pending on the make of the tyres, these wear indicators are located at uniform 81 462 kg
intervals around the circumference of the tyre » Fig. 111 – . Markings on the 83 487 kg
walls of the tyres through the letters “TWI”, triangular symbols or other symbols 85 515 kg
identify the position of the wear indicators.
87 545 kg 

Wheels 133
91 615 kg
Spare wheel
92 630 kg
93 650 kg
Fig. 113
Speed symbol Luggage compartment: Spare
This indicates the maximum permissible vehicle speed with fitted tyres in each wheel
category.
P 150 km/h
Q 160 km/h
R 170 km/h
S 180 km/h
T 190 km/h
U
H
200 km/h
210 km/h
 First read and observe the introductory information and safety warn-
ings on page 131.

The spare wheel is located in a well under the floor covering in the luggage com-
CAUTION partment and is fixed in place with a special bolt » Fig. 113.
The information about the load index and the speed symbol is listed in your vehi- Before removing the spare wheel, the box containing the vehicle tool kit must be
cle documents.  removed.
If the dimensions or design of the spare wheel differ from the tyres fitted to the
vehicle (e.g. winter tyres or low-profile tyres), it must only be used briefly in the
Unidirectional tyres event of a puncture and if an appropriately cautious style of driving is adop-
ted » .
 First read and observe the introductory information and safety warn-
ings on page 131. Fit a wheel in the appropriate dimensions and design as soon as possible.

The direction of rotation of the tyres is marked by arrows on the wall of the tyre. Temporary spare wheel
A warning label is displayed on the rim of the temporary spare wheel.
The indicated direction of rotation must be adhered to in order to ensure the op-
timal characteristics of these tyres. Please note the following if you intend to use this wheel.
These characteristics mainly relate to the following:
› The warning label must not be covered after installing the wheel.
› Be particularly observant when driving.
 Increased driving stability. › The inflation pressure for the temporary spare wheel is identical to the maxi-
 Reduced risk of aquaplaning. mum inflation pressure for the standard tyres.
 Reduced tyre noise and tyre wear.  › Only use this temporary spare wheel to reach the nearest specialist garage, as it
is not intended for long-term use. 

134 General Maintenance

 WARNING Wheel bolts
■ Never use the temporary spare wheel if it is damaged.
■ If the dimensions or design of the temporary spare wheel differ from the fit- Fig. 114
ted tyres, never drive faster than 80 km/h (or 50 mph). Remove the cap
■ Avoid accelerating at full throttle, sharp braking and fast cornering.

CAUTION
Observe the instructions on the warning label attached to the spare wheel. 

Full wheel trim

 First read and observe the introductory information and safety warn-
ings on page 131.
 First read and observe the introductory information and safety warn-
ings on page 131.

Pulling off
Pulling off › Push the extraction pliers sufficiently far onto the cap until the inner catches of
› Hook the clamp found in the vehicle tool kit into the reinforced edge of the the pliers are positioned at the collar of the cap » Fig. 114.
wheel trim. › Remove the cap.
› Push the wheel wrench through the clamp, support on the tyre and pull off the Install
wheel trim.
› Push the caps onto the wheel bolts up to the stop.
Install
The wheel bolt caps are housed in a plastic box in the spare wheel or in the stor-
› Press the wheel trim onto the wheel rim at the designated valve opening. age space for the spare wheel. 
› Then press the trim into the wheel rim until its entire circumference locks cor-
rectly in place.
Wheel bolts
CAUTION
■ Use the pressure of your hand, do not knock the full wheel trim! Avoid heavy
impacts when the trim has not yet been inserted into the wheel rim. This could
cause damage to the guide and centring elements of the trim.
 First read and observe the introductory information and safety warn-
ings on page 131.

Wheels and wheel bolts are matched to each other in terms of design. Each time
■ Make sure that the anti-theft wheel bolt is mounted in the bore in the area near
you fit other wheels rims, e.g. light alloy wheel rims or wheels with winter tyres,
the valve » page 141, Securing wheels against theft.
you must also use the matching wheel bolts with the correct length and dome
■ If wheel trims are retrofitted it must be ensured that an adequate flow of air is
shape. This is essential to ensure that the wheels are tightly fitted and that the
assured to cool the brake system. 
brake system operates properly. 

Wheels 135
 For technical reasons, it is only permissible to fit snow chains with the following
Winter operation wheel/tyre combinations.

Tyre size Rim

 Introduction
165/70 R14 5J x 14 ET 35
This chapter contains information on the following subjects:
Only fit snow chains with links and locks not larger than 15 mm.
Winter tyres 136
Remove the full wheel trims before installing the snow chains.
Snow chains 136 
CAUTION
Winter tyres The chains must be removed when driving on roads which are free of snow. They
adversely affect the handling of your vehicle, damage the tyres and are rapidly

 First read and observe the introductory information given on page 136. destroyed. 

Fitting winter tyres will significantly improve the handling of your vehicle when
driving in wintry road conditions. Summer tyres have less grip on ice, snow and at
temperatures below 7 °C. This is especially true of wide tyres or high-speed tyres.
In order to achieve the best possible handling properties, winter tyres must be fit-
ted on all 4 wheels, the minimum tread depth must be 4 mm and tyres must be
no older than 4 years.
Winter tyres of a lower speed category can be used provided that the permissible
maximum speed of these tyres is not exceeded even if the possible maximum
speed of the vehicle is higher.

For the sake of the environment

Fit the summer tyres on again in good time as they provide better handling prop-
erties, a shorter braking distance, less tyre noise, and reduced tyre wear on roads
which are free of snow and ice as well as at temperatures above 7 °C. The fuel
consumption is also lower. 

Snow chains

 First read and observe the introductory information given on page 136.

When driving in wintry road conditions, snow chains improve not only traction,
but also the braking performance.
Snow chains must only be mounted on the front wheels.

136 General Maintenance

 Fire extinguisher
Do-it-yourself

Emergency equipment and self-help

 First read and observe the introductory information given on page 137.

The fire extinguisher is located at a holder in the foot well in front of the front
passenger seat.
Emergency equipment Please read carefully the instructions which are attached to the fire extinguish-
er.
 Introduction The fire extinguisher must be checked by an authorised person on an annual ba-
sis (the national legal provisions must be observed).
This chapter contains information on the following subjects:
First-aid kit and warning triangle 137 WARNING
Fire extinguisher 137
The fire extinguisher must always be secured safely so that they do not come
Vehicle tool kit 138 
loose when making an emergency braking or in a vehicle collision which could
cause injuries to occupants.
First-aid kit and warning triangle
Note
 First read and observe the introductory information given on page 137.
■ The fire extinguisher must comply with the relevant applicable national legal re-
quirements.
The warning triangle can be stowed away underneath the floor covering of the ■ Pay attention to the expiration date of the fire extinguisher. If the fire extin-
luggage compartment. guisher is used after the expiration date, its proper function is no longer assured.
■ The fire extinguisher is part of the scope of delivery in certain countries only. 
WARNING
The first-aid kit and warning triangle must always be secured safely so that
they do not come loose when making an emergency braking or in a vehicle
collision which could cause injuries to occupants.

Note
■ Pay attention to the expiration date of the first-aid kit.
■ We recommend using a first-aid kit from ŠKODA Original Accessories, which are
available from a ŠKODA Partner. 

Emergency equipment and self-help 137

 Vehicle tool kit WARNING
■ The factory-supplied lifting jack is only intended for your model of vehicle.
Under no circumstances use it to lift heavier vehicles or other loads – risk of
injury!
■ Ensure that the vehicle tool kit is safely secured in the luggage compart-
ment.
■ Ensure that the box is always secured with the strap. 

Changing a wheel
Fig. 115 Luggage compartment: Storage for your vehicle tool kit/parts of the  Introduction
vehicle tool kit
This chapter contains information on the following subjects:

 First read and observe the introductory information given on page 137.
Preliminary work
Changing a wheel
139
139
The vehicle tool kit and the lifting jack with sticker are housed in a box in the Follow-up work 139
spare wheel or in the compartment for the spare wheel underneath the floor cov- Loosening/tightening wheel bolts 140
ering in the luggage compartment. The box is attached with a strap on the spare
Raising the vehicle 141
wheel.
Securing wheels against theft 141
Lift up the floor covering at the opening A » Fig. 115.
The components of the vehicle tool kit (if included) » Fig. 115. WARNING
1 Towing eye ■ If you are in flowing traffic, switch on the hazard warning light system and
2 Replacement bulb set set up the warning triangle at the prescribed distance! The national legal re-
quirements must be observed.
3 Adapter for anti-theft wheel bolts ■ Park the vehicle as far away as possible from the flow of traffic. Park on as
4 Clamps for removing the wheel trims flat and firm a surface as possible.
5 Extraction pliers for wheel bolt caps ■ The following instructions must be followed if the vehicle is subsequently
6 Wheel wrench fitted with tyres or rims that differ from the factory-fitted ones » page 133,
7 Screwdriver New tyres. 

8 Car jack
Screw the car jack back into its initial position after use in order to store it back in
the box with the vehicle tool kit.

138 Do-it-yourself
 WARNING › Let all of the occupants get out. While changing a tyre, the occupants of the
vehicle should not stand on the road (instead they should remain behind a crash
Observe the following instructions for lifting the vehicle. barrier).
■ If the wheel has to be changed on a slope, first of all block the opposite › Switch off the engine.
wheel with a stone or similar object to prevent the vehicle from unexpectedly › Move the gearshift lever into Neutral or, for an automatic gearbox, move the
rolling away. selector lever into position N.
■ Secure the base plate of the lifting jack with suitable means to prevent pos- › Firmly apply the handbrake.
sible moving. A soft and slippery ground under the base plate may move the › Remove the vehicle tool kit » page 138 and the spare wheel » page 134, Spare
lifting jack, causing the vehicle to fall down. It is therefore always necessary to wheel from the luggage compartment. 

place the lifting jack on a solid surface or use a wide and stable base. Use a
non-slip base (e.g. a rubber foot mat) if the surface is smooth, such as cobbled
stones, tiled floor, etc. Changing a wheel
■ Only attach the lifting jack to the attachment points provided for this pur-
pose.
■ Always raise the vehicle with the doors closed.
■ Never position any body parts, such as arms or legs under the vehicle, while
 First read and observe the introductory information and safety warn-
ings on page 138.

the vehicle is raised with a lifting jack. › Remove the full wheel trim » page 135 or caps » page 135.
■ Never start the engine when the vehicle is raised – risk of injury. › First of all slacken the anti-theft wheel bolt and then the other wheel
bolts » page 140.
› Jack up the vehicle until the wheel that needs changing is clear of the
CAUTION ground » page 141.
› Unscrew the wheel bolts and place them on a clean surface (cloth, paper, etc.).
■ The prescribed tightening torque for the wheel bolts is 110 Nm for steel and › Remove the wheel.
light alloy wheel rims. › Attach the spare wheel and slightly screw on the wheel bolts.
■ If the wheel bolts are fastened too tightly, this can cause damage to the anti-
› Lower the vehicle.
theft wheel bolt and the adapter. › Alternately tighten the wheel bolts opposite each other using the wheel
wrench (crosswise) and then tighten the anti-theft wheel bolt » page 140.
Note › Reinstall the wheel trim/wheel trim cap or the caps.
■ The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA Part-
ner.
WARNING
■ The national legal requirements must be observed when changing a wheel.  ■ All bolts must be clean and must turn easily.
■ Under no circumstances grease or oil the wheel bolts!
■ When fitting unidirectional tyres, ensure that the direction of rotation is cor-
Preliminary work rect » page 131. 

 First read and observe the introductory information and safety warn-
ings on page 138.
Follow-up work
Always change a wheel on a level surface as far as possible.
The following steps must be carried out before actually changing the wheel:
 First read and observe the introductory information and safety warn-
ings on page 138.

The following steps must also be performed after changing the wheel. 

Emergency equipment and self-help 139

› Stow and attach the replaced wheel in the spare wheel compartment using a Tightening
special screw » page 134. › Push the wheel wrench onto the wheel bolt up to the stop . 1)

› Stow the vehicle tool kit in the space provided. › Grasp the end of the wrench and turn the bolt to the right until it is tight.
› Check the tyre pressure on the installed spare wheel as soon as possible. For a wheel with full wheel trim, the anti-theft wheel bolt must be screwed in at
› Have the tightening torque of the wheel bolts checked with a torque wrench position 2 » Fig. 116 opposite the valve 1 . Otherwise the full wheel trim cannot
as soon as possible.
be installed.
› Replace the damaged wheel or consult a specialist garage about repair options.
WARNING WARNING
■ If it is determined that the wheel bolts are corroded and difficult to turn Undo the wheel bolts only a little (about one turn) provided that the vehicle
when changing the wheel, the bolts must be replaced before checking the has not yet been jacked up. Otherwise the wheel could come off and fall down
tightening torque. – risk of injury!
■ Drive cautiously and only at a moderate speed until the tightening torque
has been checked. 
Note
If it proves difficult to undo the bolts, carefully apply pressure to the end of the
wrench with your foot. Keep hold of the vehicle when doing so, and make sure
Loosening/tightening wheel bolts
you keep your footing. 

Fig. 116 Changing a wheel: Undoing the wheel bolts/installation location of

the anti-theft wheel bolt

 First read and observe the introductory information and safety warn-
ings on page 138.

Loosening
› Push the wheel wrench onto the wheel bolt up to the stop1).
› Grasp the end of the wrench and turn the bolt about one turn to the
left » Fig. 116 - .

1) Use the appropriate adapter for undoing and tightening the anti-theft wheel bolts » page 141.

140 Do-it-yourself
 Raising the vehicle Securing wheels against theft

Fig. 117 Fig. 119

Jacking points for positioning Principle sketch: Anti-theft
lifting jack wheel bolt with adapter

 First read and observe the introductory information and safety warn-
ings on page 138.

The anti-theft wheel bolts on vehicles fitted with them (one anti-theft wheel bolt
per wheel) can only be loosened or tighten up by using the adapter provided.
› Pull off the full wheel trim from the wheel rim or the cap from the anti-theft
wheel bolt.
› Insert the adapter B » Fig. 119 with its toothed side fully into the inner toothing
of the safety wheel bolt A until the stop so that only the outer hexagon is jut-
ting out.
› Push the wheel wrench onto the adapter B up to the stop.
Fig. 118 Attach lifting jack › Loosen or tighten the wheel bolt » page 140.
› After removing the adapter, reinstall the full wheel trim or place the cap onto
the anti-theft wheel bolt.
 First read and observe the introductory information and safety warn-
ings on page 138. › Have the tightening torque checked with a torque wrench as soon as possible.
It is advisable to make a note of the code number hammered into the rear side of
Position the lifting jack by selecting the jacking point that is closest to the faulty
wheel » Fig. 117. The jacking point is located directly below the engraving in the the adapter or the rear side of the anti-theft wheel bolt. This number can be used
lower sill. to purchase a replacement adapter from ŠKODA Original Parts if necessary.
We recommend that you always carry the adapter for the wheel bolts with you in
› Position the lifting jack below the jacking point and move it up until its claw is the vehicle. It should be stowed in the vehicle tool kit. 
positioned directly below the vertical web of the lower sill.
› Align the lifting jack so that its claw grasps the web » Fig. 118 –  below the
embossing in the side surface of the lower sill.
› Ensure that the entire surface of the lifting jack base plate rests on level ground
and is located in a vertical position to the area » Fig. 118 where the claw grasps
the web.
› Continue turning up the jack until the wheel is just about lifted off the ground. 

Emergency equipment and self-help 141

 WARNING (Continued)
Breakdown kit
■ A tyre filled with sealant has the same driving characteristics as a standard
 Introduction tyre.
■ Do not drive faster than 80 km/h (50 mph).
This chapter contains information on the following subjects: ■ Avoid accelerating at full throttle, sharp braking and fast cornering.
■ Check the tyre inflation pressure after driving for 10 minutes!
Components of the breakdown kit 143 ■ The sealant is hazardous to heath. Remove immediately if it comes into con-
Preparing to use the breakdown kit 143 tact with the skin.
Sealing and inflating tyres 143
Check after driving for 10 minutes 144
For the sake of the environment
The breakdown kit is located in a box under the floor covering in the luggage
compartment. Used sealant or sealant whose expiry date has passed must be disposed of in ac-
cordance with environmental protection regulations.
Use the breakdown kit to reliably repair tyre damage caused by foreign bodies or
a puncture with diameters up to approx. 4 mm. Do not remove foreign bodies, e.g. Note
screws or nails, from the tyre!
■ Observe the manufacturer's usage instructions for the breakdown kit.
The repair can be undertaken on the vehicle immediately.
■ A new bottle of sealant can be purchased from ŠKODA Original Accessories.
Repairs using the breakdown kit do not in any way replace a permanent tyre re- ■ Immediately replace the tyre that was repaired using the breakdown kit, or con-
pair; they are only intended for reaching the closest specialist garage. sult a specialist garage about repair options. 

The breakdown kit must not be used under the following circumstances:
› if there is damage to the wheels;
› in outside temperatures of less than -20 °C;
› with tears or punctures greater than 4 mm in size;
› if there is damage to the tyre wall;
› when driving with very low tyre pressure or with a completely flat tyre;
› if the use-by-date (see inflation bottle) has passed.
WARNING
■ If you are in flowing traffic, switch on the hazard warning light system and
set up the warning triangle at the prescribed distance! The national legal re-
quirements must be observed. In this way you are not only protecting yourself
but other road users as well.
■ If the wheel is damaged or in the event of a puncture, park the vehicle as far
away as possible from the flow of traffic. Park on as flat and firm a surface as
possible.

142 Do-it-yourself
 Components of the breakdown kit Preparing to use the breakdown kit

 First read and observe the introductory information and safety warn-
ings on page 142.

The following preparatory work must be carried out before using the breakdown
kit.
› In the event of a puncture, park the vehicle as far away as possible from the
flow of traffic. Park on as flat and firm a surface as possible.
› Let all of the occupants get out. While changing a tyre, the occupants of the
vehicle should not stand on the road (instead they should remain behind a crash
barrier).
› Switch off the engine and move the gearshift lever into Neutral or move the
selector lever for the automatic gearbox into position N.
› Firmly apply the handbrake.
› Check that you can carry out the repairs with the breakdown kit » page 142,
Fig. 120 Components of the breakdown kit Breakdown kit.
› Remove the breakdown kit from the luggage compartment.
 First read and observe the introductory information and safety warn-
ings on page 142.
› Stick the sticker 2 » Fig. 120 on page 143 on the dash panel in view of the driv-
er.
› Do not remove the foreign body, e.g. screw or nail, from the tyre.
The breakdown kit contains the following parts:
› Unscrew the valve cap.
1 Valve remover › Use the valve remover 1 to unscrew the valve core and place it on a clean sur-
2 Sticker with speed designation “max. 80 km/h”/“max. 50 mph” face (rag, paper, etc.). 

3 Inflation hose with plug

4 Air compressor
Sealing and inflating tyres
5 Tyre inflation hose
6 Tyre inflation pressure indicator
7 Air release valve
8 ON and OFF switch
 First read and observe the introductory information and safety warn-
ings on page 142.

Sealing
9 12 volt cable connector
› Forcefully shake the tyre inflator bottle 10 » Fig. 120 on page 143 several times.
10 Tyre inflator bottle with sealing agent
› Firmly screw the inflation hose 3 onto the tyre inflator bottle 10 clockwise.
11 Replacement valve core The film on the cap is pierced automatically.
The valve remover 1 has a slot at its lower end which fits into the valve core. › Remove the plug from the inflation hose 3 and plug the open end fully onto
This is the only way in which you can remove and re-install the valve core from the tyre valve.
the tyre valve. The same also applies to the replacement valve core 11 .  › Hold the bottle 10 with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
› Remove the empty tyre inflator bottle from the valve.
› Screw the valve core back into the tyre valve using the valve remover 1 . 

Emergency equipment and self-help 143

Inflating
› Screw the tyre inflation hose 5 » Fig. 120 on page 143 of the air compressor Check after driving for 10 minutes
firmly onto the tyre valve.
› Check that the air release valve 7 is closed.
› Start the engine and run it in idle.  First read and observe the introductory information and safety warn-
ings on page 142.
› Plug the connector 9 into 12 Volt socket » page 50, 12-volt power socket. Check the tyre inflation pressure after driving for 10 minutes!
› Switch on the air compressor with the ON and OFF switch 8 .
› Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved. Max- If the tyre inflation pressure is 1.3 bar or less:
imum run time of 8 minutes » ! ›  Do not drive the vehicle! You cannot properly seal with tyre with the break-
› Switch off the air compressor. down kit.
› If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation › Get professional assistance.
hose 5 from the tyre valve.
If the tyre inflation pressure is 1.3 bar or more:
› Drive the vehicle 10 metres forwards or backwards to allow the sealing agent to › Adjust the tyre inflation pressure to the correct value (see inside of fuel filler
“distribute” in the tyre.
cap).
› Firmly screw the tyre inflation hose 5 back onto the tyre valve and repeat the › Continue driving carefully to the nearest specialist garage at a maximum speed
inflation process.
of 80 km/h (50 mph). 
› If you cannot reach the required tyre inflation pressure here either, this means
the tyre has sustained too much damage. You cannot seal with tyre with the
breakdown kit » .
› Switch off the air compressor. Jump-starting
› Remove the tyre inflation hose 5 from the tyre valve.
Once a tyre inflation pressure of 2.0 – 2.5 bar is achieved, continue the journey at  Introduction
a maximum speed of 80 km/h (50 mph).
This chapter contains information on the following subjects:
Check the tyre inflation pressure after driving for 10 minutes » page 144.
Jump-starting 145
WARNING Jump-starting in vehicles with the START-STOP system 146

■ During inflation, the tyre inflation hose and air compressor may get hot- risk The battery of another vehicle can be used to jump-start your vehicle if the en-
of injury! gine will not start because the battery is flat. Jump-start cables are required for
■ Do not place the hot tyre inflation hose or hot air compressor on flammable this purpose.
materials – risk of fire! Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the battery
■ If you cannot inflate the tyre to at least 2.0 bar, this means the damage sus-
supplying the power must not be significantly less than the capacity of the dis-
tained was too serious. The sealing agent cannot be used to seal the tyre.  charged battery in your vehicle.
Do not carry on driving the vehicle. Get professional assistance!
Jump-start cables
Only use jump-start cables which have an adequately large cross-section and in-
CAUTION sulated terminal clamps. Observe the manufacturer's instructions.
Switch off the air compressor after running 8 minutes at the latest – danger of Positive cable – colour coding in the majority of cases is red.
overheating! Allow the air compressor to cool a few minutes before switching it
Negative cable – colour coding in the majority of cases is black. 
on again. 

144 Do-it-yourself
 WARNING Jump-starting
■ A discharged vehicle battery may already freeze at temperatures just below
0 °C. In case of frozen battery carry out no jump-starting – risk of explosion! Fig. 121
■ Pay attention to the warning instructions relating to working in the engine Jump-starting using the battery
compartment » page 120, Engine compartment. from another vehicle: A – flat ve-
■ The non-insulated parts of the terminal clamps must never make contact hicle battery, B – battery provid-
with each other. In addition, the jump-start cable connected to the positive ing current
terminal of the battery must not come into contact with electrically conduct-
ing parts of the vehicle – risk of short circuit!
■ Do not clamp the jump-start cable to the negative terminal of the dis-
charged battery. There is the risk of detonating gas seeping out the battery
being ignited by the strong spark which results from the engine being started.
■ Route the jump-start cables so that they cannot be caught by any rotating
parts in the engine compartment.
■ Do not bend over the battery – risk of caustic burns!
 First read and observe the introductory information and safety warn-
ings on page 144.

■ The vent screws of the battery cells must be tightened firmly. The jump-start cables must be attached in the following sequence.
■ Keep any sources of ignition (naked flame, smouldering cigarettes, etc.)
Connecting positive terminals
away from the battery – risk of an explosion!
■ Never jump-start vehicle batteries with an electrolyte level that is too low –
› Attach one end 1 » Fig. 121 to the positive terminal of the discharged battery
A.
risk of explosion and caustic burns.
› Attach the other end 2 to the positive terminal of the battery supplying the
power B .
Note Connecting negative terminal and engine block
■ There must not be any contact between the two vehicles otherwise current › Attach one end 3 » Fig. 121 to the negative terminal of the battery supplying
may flow as soon as the negative terminals are connected. the power B .
■ The discharged battery must be properly connected to the system of the vehi- › Attach the other end 4 to a solid metal part which is connected firmly to the
cle. engine block, or to the engine block itself.
■ We recommend you buy jump-start cables from a car battery specialist. 
Starting engine
› Start the engine on the vehicle providing the power and allow it to idle.
› Now start the engine of the vehicle with the discharged battery.
› If the engine does not start, terminate the attempt to start the engine after
10 seconds and wait for about 30 seconds before repeating the process.
› Disconnect the cables in exactly the reverse order to the one described above. 

Emergency equipment and self-help 145

 Jump-starting in vehicles with the START-STOP system › On vehicles with a manual transmission, only push down on the accelerator
pedal once the rope is taught.
The maximum towing speed is 50 km/h.
Fig. 122
Engine compartment: Engine Driver of the towed vehicle
earth › Switch on the ignition so that the steering wheel is not blocked and so that the
turn signal lights, horn, windscreen wipers and windscreen washer system can
be switched on.
› Take the vehicle out of gear or move the selector lever into position N if the ve-
hicle is fitted with an automated transmission.
Please note that the brake servo unit and power steering only operate if the en-
gine is running. If the engine is not running, significantly more physical force is re-
quired to depress the brake pedal and steer the vehicle.

 First read and observe the introductory information and safety warn-
ings on page 144. If using a tow rope, ensure that it is always kept taught.

On vehicles with the START-STOP system, the jump-start cable of the charger CAUTION
must never be connected directly to the negative pole of the vehicle battery, but
only to the engine earth » Fig. 122.  ■ Do not tow start the engine - danger of damaging the engine! On vehicles with
a catalytic converter, unburnt fuel may get into the catalytic converter where it
may ignite. This in turn may damage or destroy the catalytic converter. The bat-
tery from another vehicle can be used as a jump-start aid » page 144, Jump-start-
Towing the vehicle ing.
■ If the gearbox of your vehicle no longer contains any oil because of a defect,
 Introduction your vehicle must only be towed in with the driven wheels raised clear of the
ground, or on a special vehicle transporter or trailer.
This chapter contains information on the following subjects: ■ The vehicle must be transported on a special vehicle or trailer if it is not possible
to tow in the vehicle in the way described or if the towing distance is greater than
Front towing eye 147 50 km.
Vehicles with manual transmission can be towed in with a tow bar or a tow rope ■ To protect both vehicles when tow-starting or towing, the tow rope should be
or with the front or rear wheels raised. elastic. Thus one should only use plastic fibre rope or a rope made out of a simi-
larly elastic material.
Vehicles with automated transmission can be towed with a tow bar or a tow rope ■ One should be constantly vigilant not to allow impermissibly high towing forces
or with the front wheels raised. If the vehicle is raised at rear, the automatic gear- or jerky loadings. There is always a risk of excessive stresses and damage result-
box is damaged! ing at the points to which you attach the tow rope or tow bar when you attempt
A tow bar is the safest way of towing a vehicle and also minimises any shocks. to tow a vehicle which is not standing on a paved road.
Only use a tow rope if a suitable tow bar is not available. ■ Attach the tow rope or the tow bar only to the towing eye » page 147. 

When towing, the following guidelines must be observed.

Driver of the tow vehicle
› Release the clutch particularly gently when starting off or depress the accelera-
tor particularly gently if the vehicle is fitted with an automated transmission.

146 Do-it-yourself
 Note CAUTION
■ We recommend using a tow rope from ŠKODA Original Accessories, which is The towing eye must always be screwed in fully and firmly tightened, otherwise
available from a ŠKODA Partner. the towing eye can tear when towing in or tow-starting. 
■ Towing another vehicle requires a certain amount of practice. Both drivers
should be familiar with the particular points about towing a vehicle. Unskilled
drivers should not attempt to tow in another vehicle or to be towed in.
■ When towing, respect the national legal provisions, especially those which re-
late to the identification of the towing vehicle and the vehicle being towed.
■ The tow rope must not be twisted as it may in certain circumstances result in
the front towing eye being unscrewed out of your vehicle. 

Front towing eye

Fig. 123 Front bumper: Cap/installing the towing eye

 First read and observe the introductory information and safety warn-
ings on page 146.

The towing eye is stored in the box of the vehicle tool kit.
› Press on the lower area of the cover (arrow) » Fig. 123 -  to loosen the latch of
the cover.
› Remove the cap from the front bumper and leave it hanging on the vehicle.
› Screw in the towing eye by hand up to the stop » Fig. 123 - . For tightening
purposes, we recommend, for example, using the wheel wrench, towing eye
from another vehicle or a similar object that can be pushed through the eye.
› To re-fit the cover after removing the towing eye, first insert the cover in the
bottom region then carefully press on the upper area of the cover. The cap must
engage firmly.

Emergency equipment and self-help 147

 WARNING
Fuses and light bulbs
Always read and observe the warnings before completing any work in the en-
gine compartment » page 120, Engine compartment.
Fuses
CAUTION
 Introduction
■ Never “repair” fuses and also do not replace them with a fuse of a higher am-
This chapter contains information on the following subjects: perage - risk of fire! This may also cause damage at another part of the electrical
system.
Fuses on the underside of the dash panel 148 ■ If a newly inserted fuse blows again after a short time, have the electrical sys-
Fuses in the engine compartment 150 tem checked as quickly as possible by a specialist garage.
Fuses in the dash panel 150
Individual electrical circuits are protected by fuses. Note
› Before replacing a fuse, switch off the ignition and the appropriate consumer ■ We recommend always carrying replacement fuses in the vehicle. A box of re-
› Find out which fuse belongs to the component that is not operat- placement fuses can be purchased from ŠKODA Original Accessories.
ing » page 148, Fuses on the underside of the dash panel, » page 150, Fuses ■ There can be several power consuming devices for one fuse.
in the engine compartment, or » page 150, Fuses in the dash panel. ■ Multiple power consuming devices can share a single fuse. 

› Take the plastic clip out of its fixture in the cover of the fuse box, place it on the
relevant fuse and pull it out.
› A blown fuses is recognisable by the molten metal strip. Replace the faulty fuse Fuses on the underside of the dash panel
with a new one of the same amperage.
Colour coding of fuses
Colour Maximum amperage
purple 3
light brown 5
brown 7.5
red 10
blue 15
yellow 20
white 25 Fig. 124 Underside of the dash panel: Fuse box/schematic diagram of the
green 30 fuse box
orange 40
 First read and observe the introductory information and safety warn-
ings on page 148.

The fuses are located underneath the steering wheel on the underside of the
dash panel » Fig. 124. 

148 Do-it-yourself
› Press the locking mechanism 1 and carefully open the cover in the direction of No. Power consumer
the arrow.
32 Turn signal, brake light
› After the fuse has been replaced, fold the cover upwards in the opposite direc-
tion of the arrow so that it audibly latches. 33 Main beam
34 Instrument cluster, main beam
Fuse assignment on the underside of the dash panel
35 Not assigned
No. Power consumer
36 Cigarette lighter, 12-volt power socket
1 Telephone, radiator fan, instrument cluster, engine control unit
37 Air blower for heating and air conditioning
2 Diagnostic connection, AC compressor
38 Radio
3 Clutch pedal switch, brake pedal switch
39 Panoramic sliding roof, horn
4 Daytime running lights
40 Engine control unit
5 Steering column switch
41 Central locking system
6 Headlamp beam adjustment, exterior mirror adjustment
42 Ignition module
7-8 Automated transmission
43 Seat heaters
9 Airbag
44 Fuel pump
10 Park Assist
45 Light switch
11 Low beam
46 Rear window heater
12 Rear fog lights
47 Power windows - right
13 Low beam
48 Horn
14 Rear window wiper
49 Windscreen wipers
15 Light switch
50 Fog lights
16 Steering force assistance
51 Power windows - left 
17 Windscreen washer
18 Reverse light switch
19 Injection valves, coolant pump
20 ABS/ESP, switch wiring harness
21 Switch illumination, number plate light
22 Daytime running lights
23 Light switch
24-26 Steering column switch
27 Interior lighting
28 Diagnostic connector
29 Central control unit
30 Exterior mirror heater
31 Cooler fan, regulator valve, lambda probe

Fuses and light bulbs 149

 Fuses in the engine compartment Fuses in the dash panel

Fig. 125 Engine compartment: Distribution board cover/fuses Fig. 126 On the driver's side of the dash panel: Fuse box cover/Schematic di-
agram of the fuse box

 First read and observe the introductory information and safety warn-
ings on page 148.
 First read and observe the introductory information and safety warn-
ings on page 148.
The fuses are located underneath a cover next to the vehicle battery » Fig. 125.
The fuses are located on the left-hand side of the dashboard behind a cover on
› Press together the interlocks of the cover A simultaneously and press the cov-
vehicles with the START STOP system.
er upwards in the direction of the arrow.
› After the fuse has been replaced, place the cover on the fuse box and fold up- › Insert a suitably flat object, e.g. a screwdriver, into the slot in the region of the
wards in the opposite direction of the arrow so that it audibly latches. arrow » Fig. 126, carefully prise out the cover and remove.
Fuse assignment in engine compartment
› After the fuse has been replaced, place the cover on the fuse box and press it
until it audibly latches.
No. Power consumer
Fuse assignment in the dash panel
S1 ABS/ESP
No. Power consumer
S2 Radiator fan
1 ABS/ESP
S3 Battery management, control unit for radiator fan
2 Instrument cluster
S4 ABS/ESP
3 Radio, diagnosis
S5 Central control unit
4 DC-DC voltage converter, starter relay
S6 Ignition lock, starter 
5 Not assigned
6 Air blower for air conditioning/heating
7 Control unit for the AC system
8 Not assigned
9 Right light
10 Left light 

150 Do-it-yourself
 No. Power consumer CAUTION
11 Starter
■ Do not take hold of the glass bulb with naked fingers (even the smallest
12 DC-DC voltage converter 
amount of dirt reduces the working life of the light bulb). Use a clean cloth, nap-
kin, or similar.
■ When removing and installing the number plate light and tail light make sure
Bulbs that the paintwork of the vehicle and the tail light are not damaged.

Note
 Introduction
■ This Owner's Manual only describes the replacement of bulbs where it is possi-
This chapter contains information on the following subjects: ble to replace the bulbs on your own without any complications arising. Other
Headlights 151 bulbs must be replaced by a specialist garage.
■ We recommend that a box of replacement bulbs always be carried in the vehi-
Replacing the bulb for the side turn signal lights 152
cle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.
Replacing the bulb for the fog light 152
■ We recommend having the headlight settings checked by a specialist garage af-
Replacing the bulb for the licence plate light 153 ter replacing a bulb in the main or low beam.
Tail light 153 ■ Other LEDs must be replaced by a specialist garage. 

Some manual skills are required to change a bulb. For this reason, we recommend
having bulbs replaced by a specialist garage or seeking other expert help in the
event of any uncertainties. Headlights
› Switch off the ignition and all of the lights before replacing a bulb.
› Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
› A stowage compartment for replacement bulbs is located in a plastic box in the
spare wheel or underneath the floor covering in the luggage compartment.

WARNING
■ Accidents can be caused if the road in front of the vehicle is not sufficiently
illuminated and the vehicle cannot or can only be seen with difficulty by other
road users.
■ Always read and observe the warnings before completing any work in the Fig. 127 Left headlight - engine compartment: Arrangement/lamp removal
engine compartment » page 120, Engine compartment.
■ The H4 bulb is pressurised and may explode during a bulb replacement - risk
of injury! We therefore recommended wearing gloves and safety glasses when
changing a bulb.
 First read and observe the introductory information and safety warn-
ings on page 151.

Open the bonnet before replacing the bulb in the front headlight » page 121,
Opening and closing the bonnet.
Bulb arrangement in the front headlight
A - Front turn signal light » Fig. 127 

Fuses and light bulbs 151

B - Low beam and main beam
C - Parking and daytime running light  First read and observe the introductory information and safety warn-
ings on page 151.

Changing the bulb for the front turn signal light › Push the side repeater turn signal light in the direction of the arrow
› Turn the bulb holder A » Fig. 127anti-clockwise up to the stop and remove. 1 » Fig. 128.
› Push the faulty bulb into the holder, turn in anti-clockwise up to the stop and › Prise the turn signal light from the body in the direction of the arrow 2 .
remove. › Remove the bulb holder 3 in the direction of arrow.
› Insert a new bulb into the socket and turn clockwise to the stop. › Remove the faulty bulb from the socket.
› Insert the lamp holder with the new bulb into the headlamp and turn it clock- › Insert a new bulb into the socket.
wise until it stops. › Replace the bulb holder.
› Set the side repeater turn signal light with the side facing the rear of the vehi-
Replacing the bulb for low beam and main beam cle in the body and lightly press it until the spring on the other side of the side
› Remove the connector on the bulb B » Fig. 127. repeater turn signal light latches. 
› Remove the rubber cover.
› Press the circlip D in the direction of the headlamp and then unhook in the di-
rection of the arrow. Replacing the bulb for the fog light
› Remove the light bulb and insert a new light bulb in such a way that the fixing
lugs of the light bulb socket fit into the recesses at the headlight.
Installation is carried out in the reverse order.
Replacing the bulb for the front parking light and daylight running light
› Turn the bulb holder C » Fig. 127anti-clockwise up to the stop and remove.
› Remove the faulty bulb from the socket.
› Insert a new bulb into the socket.
› Insert the lamp holder with the new bulb into the headlamp and turn it clock-
wise until it stops. 

Replacing the bulb for the side turn signal lights Fig. 129 Front wheel houe: Changing light bulbs for fog lights

 First read and observe the introductory information and safety warn-
ings on page 151.

› Unscrew the two attachment bolts on the wheel house trim with the screwdriv-
er » page 138, Vehicle tool kit (arrows) » Fig. 129.
› Undo the expanding rivet A » Fig. 129 below on the wheel house trim with a
flat, dull object, such as a coin, remove.
› Fold the wheel house trim to the side, remove the connector 1 .
› Turn the lamp holder (bulb set- holder including bulb) anti-clockwise as far as
the stop, remove.
› Insert the lamp holder with the new bulb into the headlamp and turn it clock-
Fig. 128 Right side: Replacing the bulb for the turn signal light wise as far as the stop; insert the connector until it latches securely.
› Fold the wheel house trim back. 

152 Do-it-yourself
› Return the expanding rivet, screw in. Tail light
› Firmly tighten the two attachment bolts with the screwdriver. 

Replacing the bulb for the licence plate light

Fig. 131 Removing the tail lamp assembly

Fig. 130 Changing the bulb for the licence plate light

 First read and observe the introductory information and safety warn-
ings on page 151.

› Insert a suitable thin object, e.g. a screwdriver into the recess in the region of
the arrow and carefully prise the number plate light out of the bumper » Fig. 130
- .
› Pull the number plate light out of the bumper a little.
› Turn the bulb holder anti-clockwise and remove in the direction of the ar-
row » Fig. 130 - . Fig. 132 Tail light assembly: Replacing bulbs
› Remove the faulty bulb from the socket.
› Insert a new bulb into the socket.
› Insert the bulb holder into the number plate light and turn clockwise as far as
the stop.
 First read and observe the introductory information and safety warn-
ings on page 151.

› Insert the number plate light into the opening of the bumper at the left edge. Fold the seat rest of the rear set bench forward to make it easier to reach the
Lightly press it until the spring latches.  cover of the rear light more easily » page 43, Folding the rear seats forward.
Removing and installing the tail light
› Open the luggage compartment door and unscrew the luggage compartment
cover » page 46.
› Prise the cover 1 » Fig. 131, insert the screwdriver underneath the lower edge
of the locking mechanism 3 » page 138, Vehicle tool kit and pull the locking
mechanism at the connector 2 in the direction of arrow.
› Press the locking mechanism 4 and remove the connector 2 . 

Fuses and light bulbs 153

› Hold the tail light assembly in the installation position with one hand, and re-
move the plastic nut 5 with the other.
› Carefully remove the tail light from the body and place it on a clean, smooth sur-
face.
› Unlock the lamp holder on the locking latches (arrows) » Fig. 132 -  and re-
move the bulb holder from the tail light.
› To reinsert the bulb holder, first place the bulb housing in the tail light assem-
bly. All locking plates (arrows) must audibly snap into place.
› Carefully place the tail light assembly in the opening in the body.
› Hold the tail light assembly with one hand, and attach and tighten the plastic
nuts 5 with the other hand.
› Insert the connector 2 on the lamp holder and press the locking mechanism
towards the tail light.
› Fold the cover 1 back, install the luggage compartment cover, and close the
luggage compartment cover.
Fold the rear seat backrest back.
Replacing the bulbs in the tail lamp assembly
› Push the faulty bulb into the holder, turn anti-clockwise up to the stop and re-
move » Fig. 132 - .
› Insert a new bulb into the socket and turn clockwise to the stop. 

154 Do-it-yourself
 Technical data  First read and observe the introductory information given on page 155.

Vehicle data sticker

The vehicle data sticker » Fig. 133 is located on the base of the luggage compart-
Technical data ment and is also fixed in the service schedule.
The vehicle data sticker contains the following data:
Vehicle data 1 Vehicle identification number (VIN)
2 Vehicle type, engine power, transmission, paint number
 Introduction 3 Engine and gearbox code
4 Partial vehicle description
This chapter contains information on the following subjects:
5 Operating weight (in kg)
Vehicle identification data 155 6 Fuel consumption (in ltr./100 km) - intra-urban/extra-urban/combined
Dimensions 156 7 CO2 emission levels - combined (in g/km)
Vehicle-specific information depending on engine type 157
Type plate
The details given in the vehicle's technical documentation always take prece- The type plate » Fig. 133 is visible at the bottom of the door frame after opening
dence over the details in the Owner's Manual. the driver's door.
The listed performance values were determined without performance-reducing The type plate lists the following weights:
equipment, e.g. air conditioning system. 
8 Maximum permissible gross weight
9 Maximum permissible front axle load
Vehicle identification data 10 Maximum permissible rear axle load
Vehicle identification number (VIN)
The vehicle identification number - VIN (vehicle body number) is stamped into the
engine compartment on the right hand suspension strut dome. This number is al-
so located on a sign on the lower left hand edge below the windscreen (together
with a VIN bar code).
Engine number
The engine number is stamped into the engine block.
Operating weight
The specified operating weight is for orientation purposes only. This value repre-
sents the minimum operating weight without additional weight-increasing equip-
Fig. 133 Vehicle data sticker/type plate ment such as air conditioning system, spare wheel, or trailer hitch.
The operating weight also contains the weight of the driver (75 kg), the weight of
the operating fluids, the tool kit, and a fuel tank filled to 90 % capacity.
It is possible to calculate the approximate maximum load from the difference be-
tween the maximum permissible total weight and the operating weight » . 

Technical data 155

The payload consists of the following components:
› Passengers Dimensions
› All items of luggage and other loads
› Roof load including roof rack system
› Equipment not included in the operating weight.  First read and observe the introductory information given on page 155.

Dimensions (mm)
Fuel consumption and CO2 emissions according to ECE standards and EU
directives Length 3563
The measurement of the intra-urban cycle begins with a cold start of the engine. Width 1641/1645a)
Afterwards urban driving is simulated.
Width including exterior mirror 1910
In the extra-urban driving cycle, the vehicle is accelerated and decelerated in all Height 1478/1463b)/1480c)
gears, corresponding to daily routine driving conditions. The driving speed varies
between 0 and 120 km/h. Clearance 136/121b)/134c)
Wheel base 2420/2421c)
The calculation of the combined fuel consumption considers a weighting of about
37 % for the intra-urban cycle and 63 % for the extra-urban cycle. Track gauge front/rear 1428/1424
a) Valid for vehicles with rear side doors.
WARNING b) The value corresponds to the status with the Green tec package.
c) Valid for vehicles with CNG operation. 
Do not exceed the specified maximum permissible weights – risk of accident
and damage!

Note
■ If required, you can find out the precise weight of your vehicle at a specialist ga-
rage.
■ Depending on the range of equipment, style of driving, traffic situation, weather
influences and vehicle condition, consumption values may deviate from the indi-
cated values. 

156 Technical data

 Vehicle-specific information depending on engine type

 First read and observe the introductory information given on page 155.

The specified values have been determined in accordance with rules and under conditions set out by legal or technical requirements for determining operational and
technical data for motor vehicles.
1.0 ltr./44 kW engine
Output (kW per rpm) Max. torque (Nm at rpm) Number of cylinders/Displacement (cm3)
44/5000-6000 95/3000-4300 3/999

Driving performance MG ASG

speed (km/h) 160/161a)
Acceleration 0-100 km/h (s) 14.4 15.3
a) The value corresponds to the status with the Green tec package.

1.0 ltr./55 kW engine

Output (kW per rpm) Max. torque (Nm at rpm) Number of cylinders/Displacement (cm3)
55/6200 95/3000-4300 3/999

Driving performance MG ASG

speed (km/h) 171/172a)
Acceleration 0-100 km/h (s) 13.2 13.9
a) The value corresponds to the status with the Green tec package.

1.0 l/50 kW Engine - CNG

Output (kW per rpm) Max. torque (Nm at rpm) Number of cylinders/Displacement (cm3)
50/6200 90/3000 3/999

Performances MG
Top speed (km/h) 164
Acceleration 0-100 km/h (s) 16.3 

Technical data 157

 City Safe Drive 83 Braking 65
Index Cruise Control System 80 Information on braking 66
EDS 78 Breakdown kit 142
ESC 16, 77 Bulbs
Numbers and Symbols Parking aid 78 In the tail light 153
START/STOP 82 Replacing 151
12-volt power socket 50 TC 78 Button in the driver's door
Traction Control System (TCS) 17 Electrical power windows 27
A Visual parking system 79
Automatic gearbox 67
Abroad Information for driving 68
C
Driving abroad 76 Kickdown 70
Unleaded petrol 76 Car computer
Operational faults 70 see Multifunction display 11
ABS 78 Parking 68
Warning light 17 Car jack 138
Selector lever positions 69
Accessories 112 Carrier 47
Starting off 68
Adjusting Stopping 68 Cavity protection 109
Exterior mirror 39 Tiptronic 69 Central locking button 24
Interior mirror 38 Automatic load deactivation 130 Central locking system 23
Seat 41 Avoiding damage to the vehicle lock 24
Adjusting the seats 88 Driving through water 75 unlock 24
Aerial 105 Avoiding damage to your vehicle 75 Changing
Air-conditioning system Brake fluid 127
Engine oil 124
Air outlet vents 55 B Fuses on the underside of the dash panel 148
Airbag 95
Belts 91 Wheels 138
Deactivating 98
Deactivating the front passenger airbag 99 Belt tensioners 94 Changing a wheel
Deployment 95 Follow-up work 139
Bonnet
Front airbag 96 Preliminary work 139
Closing 121
Modifications and damage to the airbag system 113 Remove and attaching a wheel 139
Opening 121
Side airbag Head-Thorax 97 Charging a vehicle battery 129
Brake assist 77
Airbag system 95 Checking
Brake booster 66
Air conditioning system 57 Battery electrolyte level 129
Brake fluid 126 Brake fluid 127
Control elements 58 Changing 127
Recirculated air mode 59 Coolant 126
Checking 127 Engine oil 124
Air outlet vents 55 Brakes Oil level 124
Antilock Braking System 78 Brake fluid 127 Windscreen washer fluid 122
Artificial leather 111 Handbrake 66 Children and safety 100
Ash tray 49 Running in 71
Child safety
Assist systems Warning lights 14
Side airbag 101
ABS 17, 78 Child safety lock 21

158 Index
Child seat Compressed natural gas Driving
Classification 102 See CNG 116 Abroad 76
ISOFIX 103 Computer Driving through water on streets 75
on the front passenger seat 101 see Multifunction display 11 Emissions 155
TOP TETHER 104 Coolant 125 Fuel consumption 155
Use of child seats 102 Checking 126 Trailer operation 114
Use of ISOFIX child seats 103 Replenishing 126 Driving through water 75
Chrome parts Correct seated position 88
refer to Taking care of your vehicle 108 Driver 89 E
Cigarette lighter 50 Front passenger 89
City Safe Drive 83 Instructions 89 Economical and environmentally friendly driving 71
Warning light 19 Rear seats 89 Economical driving
Cleaning 105 Counter for distance driven 10 Driving at full throttle 72
Artificial leather 111 Cruise Control System 80 Energy-efficient gear switching 72
Covers of electrically heated seats 111 Looking ahead 72
Cup holder 49
Fabric 111 Regular maintenance 73
Headlight lenses 108 EDS 78
Natural leather 110
D Electrical power windows
Plastic parts 107 Dash panel insert 8 Button in the driver's door 27
Wheels 109 Daytime running lights 32 Button on the driver's door 28
Clock 12 Deactivating an airbag 98 Electronic Differential Lock 78
Clothes hooks 51 Decorative films 108 Electronic immobiliser 64
CNG 116 Defrosting rear window 35 Emergency
Checking 118 Changing a wheel 138
Digital clock 12
Fuel gauge 9 Hazard warning light system 33
Labels 119 Dipstick 124 Jump-starting 144
Natural gas as fuel 118 Display locking of the doors 22
Quality 119 Service interval 10 Towing the vehicle 146
Refuelling 117 Distance driven 10 Tyre repair 142
Safe fuel 119 Door Unlocking the luggage compartment lid 27
Switching from CNG to petrol mode 118 Child safety lock 21 Emissions 155
Cockpit Closing 22 Engine
12-volt power socket 50 Opening 22 Running in 70
Ash tray 49 Door opening lever Starting and stopping the engine 63
Cigarette lighter 50 locking of 22 Engine compartment 120
Cup holder 49 Door opening leverl Brake fluid 127
General view 7 unlocking of 22 Coolant 125
Light 34 Doors Overview 122
Storage compartments 51 Emergency locking 22 Vehicle battery 127
Compartments 51

Index 159
Engine oil 123 Gear changing
Capacity 123 lever 67 L
Changing 124 Gear switching Lever
Checking 124 Energy-efficient driving 72 Main beam 32
Replenishing 124 General view Turn signal 32
Specifications 123 Cockpit 7 Light
Engine revolutions counter 9
Cockpit 34
Environment 71 H Headlight beam adjustment 32
Environmental compatibility 74 Headlight flasher 33
Environmentally friendly driving 71 Handbrake 66 Low beam 31
ESC Head-Thorax 97 Main beam 32
Function 77 Headlights Parking light 31, 34
Warning light 16 Driving abroad 76 Replacing bulbs 151
Replacing a bulb 151 Switching lights on and off 31
F Head restraint 43 turn signal 32
Heating 56 Lighting
Films 108 Control elements 56 Luggage compartment 44
Fire extinguisher 137 Exterior mirror 39 Lights
First-aid kit 137 Rear window 35 Daytime running lights 32
Floor mats 67 Recommended settings 57 Fog lights 33
See Floor mats 67 Seats 42 Hazard warning light system 33
Front airbag 96 Heating and air-conditioning 55 Rear fog light 33
Hill hold control 77 Warning lights 14
Front seats 40
Horn 7 Loading floor 47
Fuel 115
Fuel gauge 9 Loads 155
refer to Fuel 115 I Lock
Refuelling 115 Central locking system 24
Unleaded petrol 116 Ignition 65 Locking
Fuel consumption 71 Ignition lock 65 Door opening lever 22
Fuel gauge Immobiliser 64 Emergency locking 22
Fuel gauge 9 Inertia reels 94 Remote control 25
Fuses Instrument cluster 8 Locking and unlocking from the inside 24
Assignment 148 ISOFIX 103 Luggage compartment
Colour coding 148 Bag hooks 45
Replacing 148 cover 46
J Emergency unlocking 27
Fixing nets 46
G Jacking points
Lashing eyes 45
Raise vehicle 141
Gear Jump-starting 144 Lighting 44
Recommended gear 10 see luggage compartment lid 27

160 Index
 Unlocking the luggage compartment lid 27 Recommended gear 10
Variable loading floor 47 P Refuelling 115
Luggage compartment lid 26, 27 Paintwork Fuel 115
See Paintwork care 107 Regulation
M Paintwork care 107 Headlight beam 32
Parking Remote control 25
Maintenance Synchronisation process 26
Parking aid 78
Decorative films 108 Remote control key
Visual parking system 79
Manual gear changing Replacing the battery 21
Parking ticket holder 51
See Gear changing 67 Repairs and technical alterations 112
Part replacement 112
Mirror Replacing
Additional interior mirror 38 Passive safety
Before setting off 87 Bulb for the fog light 152
Exterior 39 Bulb for the licence plate light 153
Vanity 35 Driving safety 88
Safety equipment 87 Bulb for the side turn signal lights 152
Mobile phone 60 Bulbs 151
Passive Safety 87
Modifications 112 Bulbs in the tail light 153
Pedals 67
Modifications and technical alterations Fuses 148
Floor mats 67
Airbags 113 Fuses in the dash panel 150
Service 113 Periodic wiping 37 Fuses in the engine compartment 150
Spoiler 113 Petrol Vehicle battery 130
Trailer operation 114 refer to Fuel 116 Windscreen wiper blade 38
Move & Fun 60, 61 Polishing the paintwork Windscreen wiper blades 37
Multifunction display See Taking care of your vehicle 107 Replenishing
Functions 11 Power socket Coolant 126
Memory 11 12 V 50 Engine oil 124
Operation 12 Power steering 64 Windscreen washer fluid 122
Rof rack system
O R Attachment points 48
Roof rack system
Oil Radiator fan 122 Roof load 48
See Engine oil 124 Raise vehicle 141 Running-in
Onboard computer Rear mirror The first 1500 km 70
see Multifunction display 11 Exterior 39 Running in
Operation in winter Interior 38 Brake pads 71
De-icing windows 108 Rear seats 42 Engine 70
Vehicle battery 129 Folding forward 43 Tyres 71
Outside temperature 12 Rear window heating 35
Overview Rear windows S
Engine compartment 122 Closing 29
Warning lights 14 Opening 29 Safe securing system 23
Recirculated air mode 59

Index 161
Safety 87 Sliding/tilting roof 29
Child safety 100 Closing 29 T
Child safety seats 100 Opening and tilting 29
Taking care of the vehicle
Correct seated position 88 Operation 29
Natural leather 110
Head restraints 43 Snow chains 136 Seat belts 112
ISOFIX 103 Spare wheel 134 Taking care of your vehicle 105
TOP TETHER 104 Speedometer 9 Artificial leather 111
Saving electrical energy 71 Speed symbol Automatic car wash system 105
Seals See Wheels 134 Cavity protection 109
Taking care of your vehicle 107 Spoiler 113 Chrome parts 108
Seat START/STOP Cleaning the wheels 109
Adjusting 41 Function 82 Decorative films 108
Seat belt Starting and stopping the engine 63 Door lock cylinders 109
Warning light 19 Fabric 111
Starting engine
Seat belts 91 Jump-starting 144 Headlight lenses 108
Belt tensioners 94 High-pressure cleaner 106
Starting the engine 65
Cleaning 112 Plastic parts 107
fastening and unfastening 93 START STOP Polishing the paintwork 107
Inertia reels 94 Jump-starting 146 Rubber seals 107
The physical principle of a frontal collision 92 Warning light 19 Taking care of the interior 110
Warning light 15 Steering force assistance 64 Taking care of your vehicle exterior 106
Seats Steering wheel 64 Washing 105
Folding forwards 43 Storage 51 Washing by hand 105
Head restraints 43 Storage compartment Wash system 105
Heating 42 Bag holder 53 Wax treatment 107
Seats and stowing 40 Storage compartment on the driver's side 52 Taking care of your vehicles
Selector lever Storage compartment on the front passenger Fabric covers 111
see selector lever positions 69 side 52 TCS 78
Selector lever positions 69 Storage compartment with lid on the front pas- Technical data 155
senger side 52 Tiptronic 67
Service 113
Storage compartments 51 see automatic gearbox 69
Service display 10
Meshed pockets on the front seat rests 54 Tool 138
Setting Multimedia holder 54
Air conditioning system 59 TOP TETHER 104
Photo holder 53
Heating 57 Storage compartment in the front centre console 53 Towing 146
Steering wheel 64 Storage compartments in front of the rear seats 54 Towing device 114
Setting the clock Sun visors 35 Towing eye 147
Clock 12 Traction Control System 78
Switching lights on and off 31
Side airbag 97 Warning light 17
Switching off the engine 65

162 Index
Transport Vehicle key 20 Spare wheel 134
Luggage compartment 44 Vehicle length 156 Speed symbol 134
Roof rack system 47 Vehicles with CNG mode Storing wheels 132
Transporting children safely 100 See CNG 116 Tyre pressure 132
Two-way radio systems 60 Vehicles with natural gas mode Tyre sizes 132
Type plate 155 See CNG 116 Tyre wear indicator 132
Unidirectional tyres 134
Tyre load-bearing capacity Vehicle tool kit 138
Winter tyres 136
See Wheels 133 Vehicle width 156
Window
Tyre repair 142 Visors 35 Interior 38
Tyres 131 Visual parking system 79 Windows 108
Inflation pressure 132
De-icing 108
New 133
See Wheels 133
W See Electrical power windows 27
Sizes 132 Windscreen washer fluid
Warning lights 14
Tyre wear indicator 132 Checking 122
Warning symbols 14 Replenishing 122
Warning triangle 137 Winter 122
U Washing 105 Windscreen washer system 36, 122
Automatic car wash system 105 Windscreen wipers
Underbody protection 109
by hand 105 Cleaning the windscreen wiper blades 37, 38
Unleaded petrol 76 Chrome parts 108
unlock Operation 36
High-pressure cleaner 106 Replacing the rear windscreen wiper blade 38
Central locking system 24 Water Replacing the windscreen wiper blades 37
Unlocking Driving through 75 Windscreen washer fluid 122
Remote control 25 Wax treatment Winter operation 136
Unlocking and locking 20 See Taking care of your vehicle 107 Snow chains 136
Useful equipment 48 Weights 155 Winter tyres 136
Wheel bolts Winter tyres
V Anti-theft wheel bolt 141 See Wheels 136
Caps 135
Vehicle battery Loosening and tightening 140
Automatic load deactivation 130
Wheel rims 131
Charging 129
Wheels
Checking the electrolyte level 129
Bolts 135
Disconnecting and reconnecting 130
Changing 138
Operation in winter 129
Full trim 135
Replacing 130
General information 131
Safety instructions 127
Load index 133
Vehicle data sticker 155
Replacing wheels 132
Vehicle dimensions 156 Service life of tyres 132
Vehicle height 156 Snow chains 136
vehicle identification number - VIN 155

Index 163
ŠKODA AUTO a.s. pursues a policy of constant product and model development. Reprinting, reproduction, translation, or any other use, either in whole or in part,
We trust that you will understand that changes to models in terms of shape, is not permitted without the written consent of ŠKODA AUTO a.s..
equipment and engineering, may be introduced at any time. The information
ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws.
about appearance, performances, dimensions, weight, standards and functions of
the vehicle is correct at the time of publication. Some equipment might only be Subject to change.
introduced at a later date, or might only be offered in certain markets; informa-
Issued by: ŠKODA AUTO a.s.
tion is provided by ŠKODA Partners. It is therefore not possible for legal claims to
be made based on the data, illustrations and descriptions contained in this Own- © ŠKODA AUTO a.s. 2013
er's Manual.
www.skoda-auto.com

You also can do something for the environment!

The fuel consumption of your ŠKODA and the related pollutant

emissions are determined crucially on how you drive.

The noise and the wear of the vehicle depend on the way how
you deal with your vehicle.

This Owner's Manual shows you how to use your ŠKODA vehi-
cle with utmost care for the environment while driving eco-
nomically at the same time.

Also please pay attention to those parts in the Owner's Manual

that are marked  below.

Work with us – for the sake of the environment.

Návod k obsluze
Citigo anglicky 05.2013
S10.5610.06.20
1ST 012 003 GB