PLAIN BEARINGS

& ROD ENDS

CORPORATE OFFICES
308 SPRINGHILL FARM ROAD
FORT MILL, SOUTH CAROLINA 29715
TELEPHONE (803)548-8500
FAX (803)548-8599

DISTRIBUTOR CUSTOMER SERVICE

TOLL FREE 800-523-6572
FAX (803)548-8594

LINEAR CUSTOMER SERVICE

TOLL FREE 800-462-3399
FAX (215)781-9830

This product section has been excerpted from our full

Product Reference Guide to reduce download time.
Our complete Product Reference Guide is available in
print and on CD-ROM. To receive the full version,
please contact your nearest INA Sales Office listed on
the last page of this file.
 FOREWORD
This publication was designed to serve as a quick refer- D Corrotect plating is available for most bearing de-
ence to the standard product series offered by INA USA signs. Corrotect is a patented process for zinc–iron
Corporation (INA) for its domestic market. The guide pro- and zinc–iron–cobalt plating in a thin layer which can
vides a current overview of INA products, including basic be applied to standard components. The protection
envelope dimensions and capacities, in one publication – exceeds stainless steel and the cost is half. Add
it is not an engineering design guide intended to replace suffix RR.
INA engineering catalogs. Consequently, the metric and D All sealed bearings are supplied pregreased. In
inch conversions are listed to 3 decimal places for easy most cases the standard lubricant is Shell Alvania 2
reference and rapid identification of correct replacement or equivalent. Other greases are available, some at
part(s), not 4 decimal places as necessary for quality extra cost.
control purposes.
D Unsealed bearings may not be greased when
This publication can be used to narrow the choices be- shipped.
tween the many different INA product lines and series for D Speed limits as published, are based on oil lubrica-
new designs. Detailed engineering information for new tion for open bearings or grease lubrication for
designs can be found in our traditional catalogs or by sealed bearings. The speed limits are calculated
contacting the INA Engineering Department. based on a nominal load and heat balance equation.
A significant portion of INA sales are special production Higher speeds may be allowed depending on the
sizes. The identification of those parts is sometimes diffi- application.
cult since a comprehensive listing is beyond the intent of D Dynamic capacities are published based on INA
this publication. Special part numbers take as many dif- standard usage of ISO and ABMA formulas. New
ferent forms as the series listed here, but the basic sys- life theory threshold values are published in other
tem is to use sequential numbers for each new design. INA publications.
Usually the prefix is F or FC but can include VH, INA or
D Life calculations and evaluations can be made from
the bearing type such as NA. INA maintains a technical
INA engineering based catalogs which are available
help desk to identify sizes not known or to match compet-
from your INA Sales Representative.
itors’ parts.
D Other features are available based on current pro-
The toll free 800 numbers listed will give you access to duction volumes including heat stabilization of the
INA Customer Service representatives. These represen- rings, matched bearing sets, with oil holes and
tatives can tap into INA Worldwide resources to provide grooves, etc.
the bearings you need.
Storage Life
Lubricants age naturally due to environmental influences. ABMA American Bearing Manufacturers Association
It is therefore the user’s responsibility to follow the direc- ASTM American Society Of Testing And Materials
tions given by the lubricant manufacturer. DIN Deutsches Institut für Normung e.V.
ISO International Standards Organization
The greases used in INA rolling bearings have a mineral Elges, Andrews and Corrotect are registered trademarks of
oil base and experience shows that they can be stored for INA USA Corporation.
up to 3 years without deteriorating providing the following Permaglide is a registered trademark and a product of
KOLBENSCHMIDT AG, Neckarsulm, also produced in
important conditions are met. Greensburg, Indiana, USA.
All other products and company names are trademarks or registered
D Closed storage room trademarks of their respective companies.
D Temperature between 0C and 40C
D Relative atmospheric humidity 65% or less
D Security from chemical agents
(vapors, gases, fluids) ALL RIGHTS RESERVED

D Sealed rolling bearings INA USA Corporation

308 Springhill Farm Road
The frictional torque can be considerably higher after lin- Fort Mill, SC 29715
ger storage periods than in freshly greased bearings and Reproduction of this publication in whole or in part without the express
written consent of INA USA Corporation is prohibited.
the lubricity of the grease can also have deteriorated. Although every effort has been made to ensure the accuracy of the
INA bearings have many optional features available in- information contained in this catalog, INA shall not be liable for any
omissions or errors. Purchasers should consult their own testing to
cluding: determine the suitability of any product for a particular purpose. In no
event shall INA be liable for any claims for damages based upon breach
D ISO series of bearings generally include the stan- of warranty, breach of contract, negligence, strict liability in tort, or any
dard clearance options CN, C2, C3 and C4. other legal theory.

D ISO bearing series include PN, P6 and P5 precision INA USA Corporation reserves the right to make changes / revisions to
specifications contained herein without notice.
classes.
_ Copyright 1999, 2000 INA USA Corporation
Section Contents
PLAIN BEARINGS & ROD ENDS

BEARING SERIES BEARING DESCRIPTION PAGE

INFORMATION PERMAGLIDE PLAIN BEARING, GENERAL OVERVIEW 349
INFORMATION ELGES SPHERICAL PLAIN BEARING, GENERAL OVERVIEW 351
INFORMATION ELGES ROD ENDS, GENERAL OVERVIEW 351
P / N IDENTIFICATION PERMAGLIDE PLAIN BEARINGS 352
P / N IDENTIFICATION ELGES SPHERICAL PLAIN BEARINGS 354
P / N IDENTIFICATION ELGES ROD ENDS 354
PAP INTERCHANGE, METRIC PLAIN BEARINGS 358
PAPZ INTERCHANGE, INCH PLAIN BEARINGS 359
PAW INTERCHANGE, METRIC THRUST WASHERS 360
PAPZ..P10 INCH PERMAGLIDE PLAIN BEARINGS 362
PAP..P10 METRIC PERMAGLIDE PLAIN BEARINGS 366
PAP..P11 METRIC PERMAGLIDE PLAIN BEARINGS 368
PAF..P10 METRIC PERMAGLIDE FLANGED PLAIN BEARINGS 369
PAF..P11 METRIC PERMAGLIDE FLANGED PLAIN BEARINGS 370
PAW..P10 PERMAGLIDE THRUST WASHERS 371
PAS..P10 PERMAGLIDE STRIPS 372
PAS..P11 PERMAGLIDE STRIPS 373
PAP..P20 METRIC PERMAGLIDE PLAIN BEARINGS 375
PAW..P20 PERMAGLIDE THRUST WASHERS 376
PAS..P20 PERMAGLIDE STRIPS 377
PAS..P21 PERMAGLIDE STRIPS 378
PAS..P22 PERMAGLIDE STRIPS 379
GE..DO ELGES METRIC DIN 648 SERIES E STEEL/STEEL SLIDING 380
GE..DO 2RS ELGES METRIC DIN 648 SERIES E STEEL/STEEL SLIDING SEALED 380
GE..FO ELGES METRIC DIN648 SERIES G STEEL/STEEL SLIDING WIDE INNER 382
GE..FO 2RS ELGES METRIC DIN 648 SERIES G STEEL/STEEL SLIDING WIDE INNER SEALED 382
GE..PB ELGES METRIC DIN 648 SERIES K STEEL/BRONZE SLIDING 383
GE..LO ELGES METRIC DIN 648 SERIES EW STEEL/STEEL SLIDING 384
GE..HO 2RS ELGES METRIC STEEL/STEEL SLIDING EXTENDED INNER SEALED 385
GE..ZO ELGES INCH STEEL/STEEL SLIDING 386
GE..ZO 2RS ELGES INCH STEEL/STEEL SLIDING SEALED 387
GE..SX ELGES METRIC STEEL/STEEL SLIDING ANGULAR CONTACT 388
GE..AX ELGES METRIC STEEL/STEEL SLIDING THRUST CONTACT 390
GE..ZSX ELGES INCH STEEL/STEEL SLIDING THRUST CONTACT 391
GE..UK ELGES METRIC DIN 648 SERIES E MAINTENANCE FREE SLIDING 392
GE..UK 2RS ELGES METRIC DIN 648 SERIES E MAINTENANCE FREE SLIDING SEALED 392
GE..DW ELGES METRIC DIN 648 SERIES C MAINTENANCE FREE SLIDING 394
GE..FW ELGES METRIC DIN 648 SERIES G MAINTENANCE FREE SLIDING 396
GE..PW ELGES METRIC DIN 648 SERIES K MAINTENANCE FREE SLIDING 398
347
Section Contents
PLAIN BEARINGS & ROD ENDS

BEARING SERIES BEARING DESCRIPTION PAGE

GE..SW ELGES METRIC MAINTENANCE FREE SLIDING ANGULAR CONTACT 400
GE..AW ELGES METRIC MAINTENANCE FREE SLIDING THRUST CONTACT 402
GIR..DO ELGES METRIC TO DIN 648 SERIES E FORM B STEEL/STEEL SLIDING INTERNAL THREAD 404
GAR..DO ELGES METRIC TO DIN 648 SERIES E FORM A STEEL/STEEL SLIDING INTERNAL THREAD 405
GIHNK..LO ELGES METRIC DIN 24338/ISO6982 STEEL/STEEL SLIDING CLAMPING THREAD 406
GIHOK..DO ELGES METRIC DIN 24555 STEEL/STEEL SLIDING CLAMPING THREAD 407
GIHR..DO ELGES METRIC STEEL/STEEL SLIDING HYDRAULIC SERIES 408
GK..DO ELGES METRIC DIN648 SERIES E STEEL/STEEL SLIDING 409
GF..DO ELGES METRIC DIN648 SERIES E STEEL/STEEL SLIDING; FOR WELDING 410
GIKMR.. ELGES METRIC DIN648 SERIES K STEEL/BRASS SLIDING 411
GAKMR.. ELGES METRIC DIN648 SERIES K STEEL/BRASS SLIDING EXTERNAL THREAD 412
GIKFR..PB ELGES METRIC DIN648 SERIES K STEEL/BRONZE SLIDING INTERNAL THREAD 413
GAKFR..PB ELGES METRIC DIN648 SERIES K STEEL/BRONZE SLIDING EXTERNAL THREAD 414
GIR..UK ELGES METRIC DIN648 SERIES E MAINTENANCE FREE INTERNAL THREAD 415
GAR..UK ELGES METRIC DIN648 SERIES E FORM A MAINTENANCE FREE EXTERNAL THREAD 416
GIKFR..PW ELGES METRIC DIN648 SERIES K MAINTENANCE FREE INTERNAL THREAD 417
GIKPR..PW ELGES METRIC DIN648 SERIES K MAINTENANCE FREE INTERNAL FINE PITCH THREAD 417
GAKFR..PW ELGES METRIC DIN 648 SERIES K MAINTENANCE FREE EXTERNAL THREAD 418

Elges is a registered trademark of INA USA Corporation

Permaglide is a registered trademark and a product of KOLBENSCHMIDT AG,
Neckarsulm, also produced in Greensburg, Indiana, USA.
348
General Information
PERMAGLIDE_ PLAIN BEARINGS

P10, P11 Maintenance–free

Structure Characteristics
Permaglide P10 is a maintenance free bearing material D High pv value; values permissible in dry running:
which consists of three layers: steel backing, bronze layer pv = 1.8 N/mm2 x m/s (51390 psi x fpm) in
and sliding layer. A 0.2 to 0.35 mm thick porous bronze continuous operation
layer (tin bronze or tin/lead bronze) is sintered onto the pv = 3.6 N/mm2 x m/s (102780 psi x fpm) for short
steel backing. In a rolling operation the pores of the periods.
bronze are completely filled with a mixture of polytetra- D High load carrying capacity; permissible static con-
fluoroethylene (PTFE) and lead (Pb). On top of the tact pressure 250 N/mm2 (36258 psi)
bronze layer there is a 0.01 to 0.03 mm thick sliding layer
D Sliding velocity up to 2 m/s (390 fpm)
of polytetrafluoroethylene (PTFE) and lead (Pb). The
steel backing and the sintered bronze skeleton give a D Good sliding properties (stick–slip virtually elimi-
very high compressive strength and provide good thermal nated)
conductivity for bearings manufactured from the D Low coefficient of friction (0.03 to 0.25)
Permaglide P10 material. The O.D., faces and butt joint D Suitable for temperatures from
of the plain bearings are coated with a tin flash for protec- –200C to +280C (–328F to +536F)
tion against corrosion.
D Well suited for rotating and oscillating motion
Permaglide P11 also consists of three layers. It has a D Low wear
bronze backing instead of a steel backing. The structure
of the porous bronze layer and the sliding layer is the D No welding tendency with metals
same as the P10 material. The bronze backing gives the D Good embedding properties for dirt and foreign
plain bearings of this material high corrosion resistance matter
and good thermal conductivity. D No absorption of water and therefore no swelling
D Chemically resistant because of suitable electro–
plating on steel backing, faces and butt joint faces
D Electrically conductive, no electrostatic charging;
advantageous for use with flammable and explosive
media
D Low mass
D Minimum space requirement

349
General Information
PERMAGLIDE PLAIN BEARINGS

P20, P21, P22 Low Maintenance

Structure Characteristics
The low maintenance plain bearing materials P20, P21
pv value up to 3 N/mm2 x m/s (85650 psi x fpm)
and P22 consist of three layers: steel backing, bronze
High load carrying capacity; permissible static con-
layer and a sliding layer. A 0.2 to 0.35 mm thick porous tact pressure 250 N/mm2 (36258 psi)
bronze layer (tin bronze or tin/lead bronze) is sintered

Sliding velocity up to 3 m/s (590 fpm)
onto the steel backing. The sliding layer consists of a
mixture of polyvinylidenefluoride (PVDF),
Low coefficient of friction (0.02 to 0.2)
polytetrafluoroethylene (PTFE) and lead (Pb). In a rolling
Suitable for temperatures from
operation the pores of the bronze are completely filled –40C to +110C (–40F to +230F),
with the mixture. The sliding layer on top of the bronze for short periods up to + 140C ( + 284F)
layer is a mixture of PVDF, PTFE and Pb. In P20 the slid-
Well suited for rotating and oscillating motion
ing layer is 0.05 to 0.1 mm thick. The O.D., faces and
butt joint of the plain bearings are coated with a tin flash
Low maintenance because of long relubrication
for protection against corrosion. intervals

Low wear
P21 and P22 materials are structurally the same as P20
although their sliding layer is thicker. The sliding layer is
Good embedding properties for dirt and foreign
between 0.15 and 0.4 mm thick making further machining matter
of the bearing surface possible. For example, bearings
Low sensitivity to edge loading
already installed can be fine turned or reamed in order to
No absorption of water
correct misalignment of the housing bores or to provide
bearings with a small radial internal clearance.

P20 is ready for assembly and has lubrication
pockets.

P21 has a machining allowance and lubrication
pockets.

P22 has a machining allowance and is without
lubrication pockets.

350
General Information
ELGES SPHERICAL PLAIN BEARINGS
AND ROD ENDS

PRODUCT DESCRIPTION
Elges Spherical Plain Bearings Elges Rod Ends

Available as inch and metric series
Available as popular metric series

Available as steel on steel sliding for high shock load
Allows adjustments in equipment by self aligning and
capacity with threaded adapter lengths

Available as chrome on PTFE for maintenance free
Available with weldable ends for hydraulic cylinders
operation
Available as standard duty and maintenance free

Many series available with seals for excluding con- designs
tamination
Many series available with seals for excluding con-

For operation in difficult applications for rolling bear- tamination
ings such as hydraulic cylinders, construction equip-
ment, dredging and others

351
Part Number Identification
PERMAGLIDE
PLAIN BEARINGS

PERMAGLIDE
PLAIN BEARINGS

PAP
PAP 10 20 P10

PREFIX Shaft Width SUFFIX

PAP Metric, Radial In Millimeters In Millimeters P10 Steel Backing,
Plain Bearing Maintenance-Free
P11 Bronze Backing,
Maintenance-Free
P20 Low-Maintenance,
Lube Pockets

PERMAGLIDE
PLAIN BEARINGS

PAPZ
PAPZ 08 12 P10

PREFIX Shaft Width SUFFIX

PAPZ Inch, Radial In Sixteenths In Sixteenths P10 Steel Backing,
Plain Bearing Of An Inch Of An Inch Maintenance-Free

PERMAGLIDE
FLANGED PLAIN BEARINGS

PAF
PAF 08 095 P10

PREFIX Shaft Width SUFFIX

PAF Metric, Flanged In Millimeters In 1/10 Millimeter P10 Steel Backing,
Plain Bearing Maintenance-Free

352
Part Number Identification
PERMAGLIDE
PLAIN BEARINGS

PERMAGLIDE
THRUST WASHERS

PAW
PAW 10 P10

PREFIX Shaft SUFFIX

PAW Metric, In Millimeters P10 Steel Backing,
Thrust Washer Maintenance-Free
P20 Low-Maintenance,
Lube Pockets

PERMAGLIDE STRIPS

PAS

PAS 15 250 P10

PREFIX Thickness Width SUFFIX

PAS Metric, Strip In 1/10 Millimeter In Millimeters P10 Steel Backing,
Maintenance-Free
P11 Bronze Backing,
Maintenance-Free
P20 Low-Maintenance,
Lube Pockets
P21 Low-Maintenance,
Lube Pockets,
Machining Allowance
P22 Low-Maintenance
Machining Allowance

353
Part Number Identification
ELGES SPHERICAL PLAIN BEARINGS
AND ROD ENDS

ELGES SPHERICAL PLAIN BEARINGS

MAINTENANCE REQUIRED

GE
GE 35 D O 2RS

Spherical Plain Bearing Shaft O Steel/Steel Sliding Surfaces, 2 Seals

Millimeters Single Axial Split In Outer Ring

Shaft in 16th
inch (ZO suffix)

D Standard Metric
F Wide Inner Ring
L Inner Ring Extended On Both
Sides
H Inner Ring Extra Extended On
Both Sides
Z Standard Inch Sizes
PB Steel/Bronze Sliding Surface,
Bronze Outer Ring Pressed
Around Inner Ring

SX Angular Contact,
Single Direction
AX Thrust, Single Direction

354
Part Number Identification
ELGES SPHERICAL PLAIN BEARINGS
AND ROD ENDS

ELGES SPHERICAL PLAIN BEARINGS

MAINTENANCE-FREE

GE
GE 35 UK 2RS

Spherical Plain Bearing Shaft RADIAL BEARINGS 2 Seals

Millimeters UK Chrome/PTFE Sliding Surfaces,
Outer Split Axially
DW Chrome/PTFE Sliding Surfaces,
Outer Split Axially
FW Chrome/PTFE Sliding Surfaces,
Wide Inner Ring,
Larger Tilting Angle
PW Steel/PTFE Sliding Surfaces,
Outer Bronze Ring, Pressed
Around Inner Ring

SW Angular Contact,
Chrome/PTFE Sliding Surfaces
AW Axial,
Chrome/PTFE Sliding Surfaces

ELGES ROD ENDS

DIN648 SERIES E

GI, GA
GI R 35 DO 2RS

GI External Threads Shaft ROD END BEARINGS 2 Seals

GA Internal Threads Millimeters DO Steel/Steel Sliding Surfaces,
Requires Maintenance
UK Chrome/PTFE Sliding Surfaces,
Maintenance Free
##R Right Hand Threads
##L Left Hand Threads

355
Part Number Identification
ELGES SPHERICAL PLAIN BEARINGS
AND ROD ENDS

ELGES HYDRAULIC ROD ENDS

GIHN, GIHO, GIHR

GIHN K 35 LO

GIHN Internal Thread Rod End Shaft DO Using GE..DO,

per DIN 24338 In Millimeters Standard Inner Width
GIHO Internal Threads LO Using GE..LO,
per DIN 24555 Extended Inner Ring
GIHR Short Internal Threads,
(Reduce Length Style)

-K Thread Clamping By Two

Hex Socket Screws
Arranged On Either Side Of
The Thread

ELGES HYDRAULIC ROD ENDS

GK, GF
GF 25 DO

GK Circular Welding Face, Shaft ROD END SPHERICAL BEARING

With Centering Pin In In Millimeters DO Steel On Steel Sliding per
Shank Bottom Series E DIN648
GF Rectangular Welding Face

356
Part Number Identification
ELGES SPHERICAL PLAIN BEARINGS
AND ROD ENDS

ELGES ROD ENDS

DIN648 SERIES K

GI, GA
GI KF R 25 PB

GI External Threads Shaft PW Steel/PTFE Sliding Surfaces,

GA Internal Threads Millimeters Outer Bronze Ring Pressed
Around Inner Ring
PB Steel/Bronze Sliding Surface,
Bronze Outer Ring Pressed
Around Inner Ring
..KF.. Standard Thread ..R Right Hand Threads
..PF.. Fine Pitch Thread To Fit ..L Left Hand Threads
Pneumatic Cylinders
..KM.. No Suffix, Steel/Brass,
Requires Relubrication

357
Interchange
Metric Plain Bearings
PAP..P10 SERIES
D Maintenance free

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PERMAGLIDE GARLOCK PERMAGLIDE GARLOCK PERMAGLIDE GARLOCK
PAP 0203 P10 MB 0203 DU PAP 2015 P10 MB 2015 DU PAP 7040 P10 MB 7040 DU
PAP 0205 P10 MB 0205 DU PAP 2020 P10 MB 2020 DU PAP 7050 P10 MB 7050 DU
PAP 0303 P10 MB 0303 DU PAP 2025 P10 MB 2025 DU PAP 7070 P10 MB 7070 DU
PAP 0304 P10 NONE PAP 2030 P10 MB 2030 DU PAP 7540 P10 NONE
PAP 0305 P10 MB 0305 DU PAP 2215 P10 MB 2215 DU PAP 7550 P10 NONE
PAP 0306 P10 MB 0306 DU PAP 2220 P10 MB 2220 DU PAP 7560 P10 MB 7560 DU
PAP 0403 P10 MB 0403 DU PAP 2225 P10 MB 2225 DU PAP 7580 P10 MB 7580 DU
PAP 0404 P10 MB 0404 DU PAP 2230 P10 MB 2230 DU PAP 8040 P10 NONE
PAP 0406 P10 MB 0406 DU PAP 2415 P10 MB 2415 DU PAP 8060 P10 MB 8060 DU
PAP 0410 P10 MB 0410 DU PAP 2420 P10 MB 2420 DU PAP 8080 P10 NONE
PAP 0505 P10 MB 0505 DU PAP 2425 P10 MB 2425 DU PAP 80100 P10 MB 80100 DU
PAP 0508 P10 MB 0508 DU PAP 2430 P10 MB 2430 DU PAP 8560 P10 MB 8560 DU
PAP 0510 P10 MB 0510 DU PAP 2515 P10 MB 2515 DU PAP 85100 P10 MB 85100 DU
PAP 0606 P10 MB 0606 DU PAP 2520 P10 MB 2520 DU PAP 9050 P10 NONE
PAP 0608 P10 MB 0608 DU PAP 2525 P10 MB 2525 DU PAP 9060 P10 MB 9060 DU
PAP 0610 P10 MB 0610 DU PAP 2530 P10 MB 2530 DU PAP 90100 P10 MB 90100 DU
PAP 0710 P10 MB 0710 DU PAP 2540 P10 NONE PAP 9560 P10 MB 9560 DU
PAP 0808 P10 MB 0808 DU PAP 2550 P10 MB 2550 DU PAP 95100 P10 MB 95100 DU
PAP 0810 P10 MB 0810 DU PAP 2820 P10 MB 2820 DU PAP 10060 P10 MB 10060 DU
PAP 0812 P10 MB 0812 DU PAP 2830 P10 MB 2830 DU PAP 100115 P10 MB 100115 DU
PAP 1008 P10 MB 1008 DU PAP 3015 P10 MB 3015 DU PAP 10560 P10 MB 10560 DU
PAP 1010 P10 MB 1010 DU PAP 3020 P10 MB 3020 DU PAP 105115 P10 MB 105115 DU
PAP 1012 P10 MB 1012 DU PAP 3025 P10 MB 3025 DU PAP 11060 P10 MB 11060 DU
PAP 1015 P10 MB 1015 DU PAP 3030 P10 MB 3030 DU PAP 110115 P10 MB 110115 DU
PAP 1020 P10 MB 1020 DU PAP 3040 P10 MB 3040 DU PAP 11550 P10 MB 11550 DU
PAP 1208 P10 MB 1208 DU PAP 3230 P10 MB 3230 DU PAP 11560 P10 NONE
PAP 1210 P10 MB 1210 DU PAP 3240 P10 MB 3240 DU PAP 11570 P10 MB 11570 DU
PAP 1212 P10 MB 1212 DU PAP 3520 P10 MB 3520 DU PAP 12060 P10 MB 12060 DU
PAP 1215 P10 MB 1215 DU PAP 3530 P10 MB 3530 DU PAP 120100 P10 MB 120100 DU
PAP 1220 P10 MB 1220 DU PAP 3540 P10 MB 3540 DU PAP 125100 P10 MB 125100 DU
PAP 1225 P10 MB 1225 DU PAP 3550 P10 MB 3550 DU PAP 13060 P10 MB 13060 DU
PAP 1310 P10 MB 1310 DU PAP 4020 P10 MB 4020 DU PAP 130100 P10 MB 130100 DU
PAP 1410 P10 MB 1410 DU PAP 4030 P10 MB 4030 DU PAP 13560 P10 MB 13560 DU
PAP 1412 P10 MB 1412 DU PAP 4040 P10 MB 4040 DU PAP 13580 P10 MB 13580 DU
PAP 1415 P10 MB 1415 DU PAP 4050 P10 MB 4050 DU PAP 14060 P10 MB 14060 DU
PAP 1420 P10 MB 1420 DU PAP 4530 P10 MB 4530 DU PAP 140100 P10 MB 140100 DU
PAP 1425 P10 MB 1425 DU PAP 4540 P10 MB 4540 DU PAP 15060 P10 MB 15060 DU
PAP 1510 P10 MB 1510 DU PAP 4550 P10 MB 4550 DU PAP 15080 P10 MB 15080 DU
PAP 1512 P10 MB 1512 DU PAP 5020 P10 MB 5020 DU PAP 150100 P10 MB 150100 DU
PAP 1515 P10 MB 1515 DU PAP 5030 P10 MB 5030 DU PAP 16080 P10 MB 16080 DU
PAP 1520 P10 MB 1520 DU PAP 5040 P10 MB 5040 DU PAP 160100 P10 MB 160100 DU
PAP 1525 P10 MB 1525 DU PAP 5060 P10 MB 5060 DU PAP 180100 P10 MB 180100 DU
PAP 1610 P10 MB 1610 DU PAP 5540 P10 MB 5540 DU PAP 200100 P10 MB 200100 DU
PAP 1612 P10 MB 1612 DU PAP 5560 P10 MB 5560 DU PAP 220100 P10 MB 220100 DU
PAP 1615 P10 MB 1615 DU PAP 6030 P10 MB 6030 DU PAP 250100 P10 MB 250100 DU
PAP 1620 P10 MB 1620 DU PAP 6040 P10 MB 6040 DU PAP 300100 P10 MB 300100 DU
PAP 1625 P10 MB 1625 DU PAP 6060 P10 MB 6060 DU
PAP 1815 P10 MB 1815 DU PAP 6070 P10 MB 6070 DU Permaglide is a registered trademark and a
product of KOLBENSCHMIDT AG, Neckarsulm,
PAP 1820 P10 MB 1820 DU PAP 6550 P10 MB 6550 DU also produced in Greensburg, Indiana, USA.
PAP 1825 P10 MB 1825 DU PAP 6560 P10 NONE All other products and company names are
trademarks or registered trademarks of their
PAP 2010 P10 MB 2010 DU PAP 6570 P10 MB 6570 DU respective companies.
358
Interchange
Inch Plain Bearings
PAPZ..P10 SERIES
D Maintenance free

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PERMAGLIDE GARLOCK PERMAGLIDE GARLOCK
PAPZ 0303 P10 03 DU 03 PAPZ 2020 P10 20 DU 20
PAPZ 0304 P10 03 DU 04 PAPZ 2210 P10 22 DU 10
PAPZ 0306 P10 03 DU 06 PAPZ 2216 P10 22 DU 16
PAPZ 0404 P10 04 DU 04 PAPZ 2228 P10 22 DU 28
PAPZ 0406 P10 04 DU 06 PAPZ 2416 P10 24 DU 16
PAPZ 0408 P10 NONE PAPZ 2420 P10 24 DU 20
PAPZ 0506 P10 05 DU 06 PAPZ 2424 P10 24 DU 24
PAPZ 0603 P10 06 DU 03 PAPZ 2432 P10 24 DU 32
PAPZ 0604 P10 06 DU 04 PAPZ 2616 P10 26 DU 16
PAPZ 0606 P10 06 DU 06 PAPZ 2624 P10 26 DU 24
PAPZ 0608 P10 06 DU 08 PAPZ 2816 P10 28 DU 16
PAPZ 0610 P10 06 DU 10 PAPZ 2824 P10 28 DU 24
PAPZ 0612 P10 06 DU 12 PAPZ 2832 P10 28 DU 32
PAPZ 0706 P10 NONE PAPZ 3216 P10 32 DU 16
PAPZ 0708 P10 07 DU 08 PAPZ 3224 P10 32 DU 24
PAPZ 0710 P10 NONE PAPZ 3232 P10 32 DU 32
PAPZ 0712 P10 07 DU 12 PAPZ 3240 P10 32 DU 40
PAPZ 0804 P10 08 DU 04
PAPZ 0806 P10 08 DU 06
PAPZ 0808 P10 08 DU 08
PAPZ 0810 P10 08 DU 10
PAPZ 0812 P10 08 DU 12
PAPZ 0814 P10 08 DU 14
PAPZ 0908 P10 09 DU 08
PAPZ 0912 P10 09 DU 12
PAPZ 1004 P10 10 DU 04
PAPZ 1008 P10 10 DU 08
PAPZ 1010 P10 10 DU 10
PAPZ 1012 P10 10 DU 12
PAPZ 1014 P10 10 DU 14
PAPZ 1204 P10 12 DU 04
PAPZ 1206 P10 12 DU 06
PAPZ 1208 P10 12 DU 08
PAPZ 1210 P10 12 DU 10
PAPZ 1212 P10 12 DU 12
PAPZ 1216 P10 12 DU 16
PAPZ 1412 P10 14 DU 12
PAPZ 1416 P10 14 DU 16
PAPZ 1608 P10 16 DU 08
PAPZ 1612 P10 16 DU 12
PAPZ 1616 P10 16 DU 16
PAPZ 1620 P10 16 DU 20
PAPZ 1624 P10 16 DU 24
PAPZ 1808 P10 18 DU 08
PAPZ 1812 P10 18 DU 12
PAPZ 1816 P10 18 DU 16
PAPZ 2012 P10 20 DU 12
PAPZ 2016 P10 20 DU 16
359
Interchange
Metric Thrust Washers
PAW..P10 SERIES
D Maintenance free

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PERMAGLIDE GARLOCK
PAW 10 P10 NONE
PAW 12 P10 WC 10 DU
PAW 14 P10 WC 12 DU
PAW 16 P10 WC 14 DU
PAW 18 P10 WC 16 DU
PAW 20 P10 WC 18 DU
PAW 22 P10 WC 20 DU
PAW 26 P10 WC 24 DU
PAW 28 P10 WC 25 DU
PAW 32 P10 WC 30 DU
PAW 38 P10 WC 35 DU
PAW 42 P10 WC 40 DU
PAW 48 P10 WC 45 DU
PAW 52 P10 WC 50 DU
PAW 62 P10 NONE

360
Permaglide Plain Bearings
PAPZ...P10 SERIES
D Inch dimensions
D Maintenance free
D Steel backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAPZ 0303 P10 3/16 4.763 1/4 6.350 3/16 4.763 0.0011 0.5
PAPZ 0304 P10 3/16 4.763 1/4 6.350 1/4 6.350 0.0015 0.7
PAPZ 0306 P10 3/16 4.763 1/4 6.350 3/8 9.525 0.0022 1.0
PAPZ 0404 P10 1/4 6.350 5/16 7.938 1/4 6.350 0.0018 0.8
PAPZ 0406 P10 1/4 6.350 5/16 7.938 3/8 9.525 0.0029 1.3
PAPZ 0408 P10 1/4 6.350 5/16 7.938 1/2 12.700 0.0037 1.7
PAPZ 0506 P10 5/16 7.938 3/8 9.525 3/8 9.525 0.0035 1.6
PAPZ 0603 P10 3/8 9.525 15/32 11.906 3/16 4.763 0.0031 1.4
PAPZ 0604 P10 3/8 9.525 15/32 11.906 1/4 6.350 0.0042 1.9
PAPZ 0606 P10 3/8 9.525 15/32 11.906 3/8 9.525 0.0064 2.9
PAPZ 0608 P10 3/8 9.525 15/32 11.906 1/2 12.700 0.0084 3.8
PAPZ 0610 P10 3/8 9.525 15/32 11.906 5/8 15.875 0.0106 4.8
PAPZ 0612 P10 3/8 9.525 15/32 11.906 3/4 19.050 0.0128 5.8
PAPZ 0706 P10 7/16 11.113 17/32 13.494 3/8 9.525 0.0073 3.3
PAPZ 0708 P10 7/16 11.113 17/32 13.494 1/2 12.700 0.0097 4.4
PAPZ 0710 P10 7/16 11.113 17/32 13.494 5/8 15.875 0.0121 5.5
PAPZ 0712 P10 7/16 11.113 17/32 13.494 3/4 19.050 0.0145 6.6
PAPZ 0804 P10 1/2 12.700 19/32 15.081 1/4 6.350 0.0055 2.5
PAPZ 0806 P10 1/2 12.700 19/32 15.081 3/8 9.525 0.0081 3.7
PAPZ 0808 P10 1/2 12.700 19/32 15.081 1/2 12.700 0.0110 5.0
PAPZ 0810 P10 1/2 12.700 19/32 15.081 5/8 15.875 0.0137 6.2
PAPZ 0812 P10 1/2 12.700 19/32 15.081 3/4 19.050 0.0165 7.5
PAPZ 0814 P10 1/2 12.700 19/32 15.081 7/8 22.225 0.0192 8.7
PAPZ 0908 P10 9/16 14.288 21/32 16.669 1/2 12.700 0.0121 5.5
PAPZ 0912 P10 9/16 14.288 21/32 16.669 3/4 19.050 0.0183 8.3
PAPZ 1004 P10 5/8 15.875 23/32 18.256 1/4 6.350 0.0066 3.0
PAPZ 1008 P10 5/8 15.875 23/32 18.256 1/2 12.700 0.0134 6.1
PAPZ 1010 P10 5/8 15.875 23/32 18.256 5/8 15.875 0.0167 7.6
PAPZ 1012 P10 5/8 15.875 23/32 18.256 3/4 19.050 0.0203 9.2
PAPZ 1014 P10 5/8 15.875 23/32 18.256 7/8 22.225 0.0236 10.7
PAPZ 1204 P10 3/4 19.050 7/8 22.225 1/4 6.350 0.0108 4.9
PAPZ 1206 P10 3/4 19.050 7/8 22.225 3/8 9.525 0.0165 7.5
PAPZ 1208 P10 3/4 19.050 7/8 22.225 1/2 12.700 0.0218 9.9
PAPZ 1210 P10 3/4 19.050 7/8 22.225 5/8 15.875 0.0271 12.3
PAPZ 1212 P10 3/4 19.050 7/8 22.225 3/4 19.050 0.0326 14.8
PAPZ 1216 P10 3/4 19.050 7/8 22.225 1 25.400 0.0434 19.7
PAPZ 1412 P10 7/8 22.225 1 25.400 3/4 19.050 0.0377 17.1
PAPZ 1416 P10 7/8 22.225 1 25.400 1 25.400 0.0502 22.8
PAPZ 1608 P10 1 25.400 1-1/8 28.575 1/2 12.700 0.0284 12.9
PAPZ 1612 P10 1 25.400 1-1/8 28.575 3/4 19.050 0.0425 19.3
PAPZ 1616 P10 1 25.400 1-1/8 28.575 1 25.400 0.0568 25.8
PAPZ 1620 P10 1 25.400 1-1/8 28.575 1-1/4 31.750 0.0709 32.2
PAPZ 1624 P10 1 25.400 1-1/8 28.575 1-1/2 38.100 0.0852 38.7
PAPZ 1808 P10 1-1/8 28.575 1-9/32 32.544 1/2 12.700 0.0403 18.3
PAPZ 1812 P10 1-1/8 28.575 1-9/32 32.544 3/4 19.050 0.0604 27.4
PAPZ 1816 P10 1-1/8 28.575 1-9/32 32.544 1 25.400 0.0804 36.5

361
Permaglide Plain Bearings
PAPZ...P10 SERIES
D Inch dimensions
D Maintenance free
D Steel backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAPZ 2012 P10 1-1/4 31.750 1-13/32 35.719 3/4 19.050 0.0665 30.2
PAPZ 2016 P10 1-1/4 31.750 1-13/32 35.719 1 25.400 0.0888 40.3
PAPZ 2020 P10 1-1/4 31.750 1-13/32 35.719 1-1/4 31.750 0.1111 50.4
PAPZ 2210 P10 1-3/8 34.925 1-17/32 38.894 5/8 15.875 0.0607 27.6
PAPZ 2216 P10 1-3/8 34.925 1-17/32 38.894 1 25.400 0.0972 44.1
PAPZ 2228 P10 1-3/8 34.925 1-17/32 38.894 1-3/4 44.450 0.1696 77.0
PAPZ 2416 P10 1-1/2 38.100 1-21/32 42.069 1 25.400 0.1057 48.0
PAPZ 2420 P10 1-1/2 38.100 1-21/32 42.069 1-1/4 31.750 0.1322 60.0
PAPZ 2424 P10 1-1/2 38.100 1-21/32 42.069 1-1/2 38.100 0.1586 72.0
PAPZ 2432 P10 1-1/2 38.100 1-21/32 42.069 2 50.800 0.2115 96.0
PAPZ 2616 P10 1-5/8 41.275 1-25/32 45.244 1 25.400 0.1145 52.0
PAPZ 2624 P10 1-5/8 41.275 1-25/32 45.244 1-1/2 38.100 0.1718 78.0
PAPZ 2816 P10 1-3/4 44.450 1-15/16 49.213 1 25.400 0.1476 67.0
PAPZ 2824 P10 1-3/4 44.450 1-15/16 49.213 1-1/2 38.100 0.2225 101.0
PAPZ 2832 P10 1-3/4 44.450 1-15/16 49.213 2 50.800 0.2952 134.0
PAPZ 3216 P10 2 50.800 2-3/16 55.563 1 25.400 0.1674 76.0
PAPZ 3224 P10 2 50.800 2-3/16 55.563 1-1/2 38.100 0.2511 114.0
PAPZ 3232 P10 2 50.800 2-3/16 55.563 2 50.800 0.3370 153.0
PAPZ 3240 P10 2 50.800 2-3/16 55.563 2-1/2 63.500 0.4207 191.0

362
Permaglide Plain Bearings
PAP...P10 SERIES
D Metric dimensions
D Maintenance free
D Steel backing
D Recommended Mounting Tolerances:
Shaft – ID<5:h6, 5"ID<80:f7, 80"ID:h8
Housing bore – OD"5.5:H6, 5.5<OD:H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 0203 P10 0.079 2 0.138 3.5 0.118 3 0.0004 0.20
PAP 0205 P10 0.079 2 0.138 3.5 0.197 5 0.0007 0.30
PAP 0303 P10 0.118 3 0.177 4.5 0.118 3 0.0004 0.19
PAP 0304 P10 0.118 3 0.177 4.5 0.157 4 0.0004 0.20
PAP 0305 P10 0.118 3 0.177 4.5 0.197 5 0.0007 0.32
PAP 0306 P10 0.118 3 0.177 4.5 0.236 6 0.0009 0.39
PAP 0403 P10 0.157 4 0.217 5.5 0.118 3 0.0005 0.24
PAP 0404 P10 0.157 4 0.217 5.5 0.157 4 0.0007 0.33
PAP 0406 P10 0.157 4 0.217 5.5 0.236 6 0.0013 0.60
PAP 0410 P10 0.157 4 0.217 5.5 0.394 10 0.0019 0.84
PAP 0505 P10 0.197 5 0.276 7 0.197 5 0.0016 0.71
PAP 0508 P10 0.197 5 0.276 7 0.315 8 0.0025 1.14
PAP 0510 P10 0.197 5 0.276 7 0.394 10 0.0031 1.43
PAP 0606 P10 0.236 6 0.315 8 0.236 6 0.0020 0.90
PAP 0608 P10 0.236 6 0.315 8 0.315 8 0.0031 1.40
PAP 0610 P10 0.236 6 0.315 8 0.394 10 0.0037 1.67
PAP 0710 P10 0.276 7 0.354 9 0.394 10 0.0040 1.80
PAP 0808 P10 0.315 8 0.394 10 0.315 8 0.0038 1.72
PAP 0810 P10 0.315 8 0.394 10 0.394 10 0.0046 2.10
PAP 0812 P10 0.315 8 0.394 10 0.472 12 0.0055 2.50
PAP 1008 P10 0.394 10 0.472 12 0.315 8 0.0044 2.00
PAP 1010 P10 0.394 10 0.472 12 0.394 10 0.0055 2.50
PAP 1012 P10 0.394 10 0.472 12 0.472 12 0.0064 2.90
PAP 1015 P10 0.394 10 0.472 12 0.591 15 0.0084 3.80
PAP 1020 P10 0.394 10 0.472 12 0.787 20 0.0116 5.28
PAP 1208 P10 0.472 12 0.551 14 0.315 8 0.0044 2.00
PAP 1210 P10 0.472 12 0.551 14 0.394 10 0.0066 3.00
PAP 1212 P10 0.472 12 0.551 14 0.472 12 0.0082 3.74
PAP 1215 P10 0.472 12 0.551 14 0.591 15 0.0103 4.68
PAP 1220 P10 0.472 12 0.551 14 0.787 20 0.0134 6.10
PAP 1225 P10 0.472 12 0.551 14 0.984 25 0.0167 7.60
PAP 1310 P10 0.512 13 0.591 15 0.394 10 0.0070 3.20
PAP 1410 P10 0.551 14 0.630 16 0.394 10 0.0077 3.50
PAP 1412 P10 0.551 14 0.630 16 0.472 12 0.0095 4.32
PAP 1415 P10 0.551 14 0.630 16 0.591 15 0.0119 5.40
PAP 1420 P10 0.551 14 0.630 16 0.787 20 0.0156 7.10
PAP 1425 P10 0.551 14 0.630 16 0.984 25 0.0194 8.80
PAP 1510 P10 0.591 15 0.669 17 0.394 10 0.0081 3.70
PAP 1512 P10 0.591 15 0.669 17 0.472 12 0.0099 4.50
PAP 1515 P10 0.591 15 0.669 17 0.591 15 0.0125 5.70
PAP 1520 P10 0.591 15 0.669 17 0.787 20 0.0167 7.60
PAP 1525 P10 0.591 15 0.669 17 0.984 25 0.0207 9.40
PAP 1610 P10 0.630 16 0.709 18 0.394 10 0.0088 4.00
PAP 1612 P10 0.630 16 0.709 18 0.472 12 0.0106 4.80
PAP 1615 P10 0.630 16 0.709 18 0.591 15 0.0134 6.10
PAP 1620 P10 0.630 16 0.709 18 0.787 20 0.0178 8.10

363
Permaglide Plain Bearings
PAP...P10 SERIES
D Metric dimensions
D Maintenance free
D Steel backing
D Recommended Mounting Tolerances:
Shaft – ID<5:h6, 5"ID<80:f7, 80"ID:h8
Housing bore – OD"5.5:H6, 5.5<OD:H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 1625 P10 0.630 16 0.709 18 0.984 25 0.0222 10.10
PAP 1815 P10 0.709 18 0.787 20 0.591 15 0.0147 6.70
PAP 1820 P10 0.709 18 0.787 20 0.787 20 0.0196 8.90
PAP 1825 P10 0.709 18 0.787 20 0.984 25 0.0244 11.10
PAP 2010 P10 0.787 20 0.906 23 0.394 10 0.0169 7.70
PAP 2015 P10 0.787 20 0.906 23 0.591 15 0.0256 11.64
PAP 2020 P10 0.787 20 0.906 23 0.787 20 0.0332 15.10
PAP 2025 P10 0.787 20 0.906 23 0.984 25 0.0420 19.10
PAP 2030 P10 0.787 20 0.906 23 1.181 30 0.0506 23.00
PAP 2215 P10 0.866 22 0.984 25 0.591 15 0.0280 12.72
PAP 2220 P10 0.866 22 0.984 25 0.787 20 0.0365 16.60
PAP 2225 P10 0.866 22 0.984 25 0.984 25 0.0464 21.10
PAP 2230 P10 0.866 22 0.984 25 1.181 30 0.0554 25.20
PAP 2415 P10 0.945 24 1.063 27 0.591 15 0.0297 13.50
PAP 2420 P10 0.945 24 1.063 27 0.787 20 0.0394 17.90
PAP 2425 P10 0.945 24 1.063 27 0.984 25 0.0502 22.80
PAP 2430 P10 0.945 24 1.063 27 1.181 30 0.0596 27.10
PAP 2515 P10 0.984 25 1.102 28 0.591 15 0.0312 14.20
PAP 2520 P10 0.984 25 1.102 28 0.787 20 0.0418 19.00
PAP 2525 P10 0.984 25 1.102 28 0.984 25 0.0526 23.92
PAP 2530 P10 0.984 25 1.102 28 1.181 30 0.0625 28.40
PAP 2540 P10 0.984 25 1.102 28 1.575 40 0.0836 38.00
PAP 2550 P10 0.984 25 1.102 28 1.969 50 0.1049 47.70
PAP 2820 P10 1.102 28 1.260 32 0.787 20 0.0634 28.80
PAP 2830 P10 1.102 28 1.260 32 1.181 30 0.0968 44.00
PAP 3015 P10 1.181 30 1.339 34 0.591 15 0.0504 22.90
PAP 3020 P10 1.181 30 1.339 34 0.787 20 0.0680 30.90
PAP 3025 P10 1.181 30 1.339 34 0.984 25 0.0847 38.52
PAP 3030 P10 1.181 30 1.339 34 1.181 30 0.1014 46.10
PAP 3040 P10 1.181 30 1.339 34 1.575 40 0.1386 63.00
PAP 3230 P10 1.260 32 1.417 36 1.181 30 0.1076 48.90
PAP 3240 P10 1.260 32 1.417 36 1.575 40 0.1437 65.30
PAP 3520 P10 1.378 35 1.535 39 0.787 20 0.0779 35.40
PAP 3530 P10 1.378 35 1.535 39 1.181 30 0.1159 52.70
PAP 3540 P10 1.378 35 1.535 39 1.575 40 0.1558 70.80
PAP 3550 P10 1.378 35 1.535 39 1.969 50 0.1954 88.80
PAP 4020 P10 1.575 40 1.732 44 0.787 20 0.0880 40.00
PAP 4030 P10 1.575 40 1.732 44 1.181 30 0.1324 60.20
PAP 4040 P10 1.575 40 1.732 44 1.575 40 0.1782 81.00
PAP 4050 P10 1.575 40 1.732 44 1.969 50 0.2222 101.00
PAP 4530 P10 1.772 45 1.969 50 1.181 30 0.1896 86.20
PAP 4540 P10 1.772 45 1.969 50 1.575 40 0.2486 113.00
PAP 4550 P10 1.772 45 1.969 50 1.969 50 0.3157 143.50
PAP 5020 P10 1.969 50 2.165 55 0.787 20 0.1391 63.21
PAP 5030 P10 1.969 50 2.165 55 1.181 30 0.2090 95.00
PAP 5040 P10 1.969 50 2.165 55 1.575 40 0.2783 126.50

364
Permaglide Plain Bearings
PAP...P10 SERIES
D Metric dimensions
D Maintenance free
D Steel backing
D Recommended Mounting Tolerances:
Shaft – ID<5:h6, 5"ID<80:f7, 80"ID:h8
Housing bore – OD"5.5:H6, 5.5<OD:H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 5060 P10 1.969 50 2.165 55 2.362 60 0.4136 188.00
PAP 5540 P10 2.165 55 2.362 60 1.575 40 0.3029 137.70
PAP 5560 P10 2.165 55 2.362 60 2.362 60 0.4554 207.00
PAP 6030 P10 2.362 60 2.559 65 1.181 30 0.2486 113.00
PAP 6040 P10 2.362 60 2.559 65 1.575 40 0.3293 149.70
PAP 6060 P10 2.362 60 2.559 65 2.362 60 0.4963 225.60
PAP 6070 P10 2.362 60 2.559 65 2.756 70 0.5819 264.50
PAP 6550 P10 2.559 65 2.756 70 1.969 50 0.4495 204.30
PAP 6560 P10 2.559 65 2.756 70 2.362 60 0.5368 244.00
PAP 6570 P10 2.559 65 2.756 70 2.756 70 0.6248 284.00
PAP 7040 P10 2.756 70 2.953 75 1.575 40 0.3828 174.00
PAP 7050 P10 2.756 70 2.953 75 1.969 50 0.4785 217.50
PAP 7070 P10 2.756 70 2.953 75 2.756 70 0.6710 305.00
PAP 7540 P10 2.953 75 3.150 80 1.575 40 0.4114 187.00
PAP 7550 P10 2.953 75 3.150 80 1.969 50 0.5133 233.30
PAP 7560 P10 2.953 75 3.150 80 2.362 60 0.6159 279.96
PAP 7580 P10 2.953 75 3.150 80 3.150 80 0.8230 374.10
PAP 8040 P10 3.150 80 3.346 85 1.575 40 0.4334 197.00
PAP 8060 P10 3.150 80 3.346 85 2.362 60 0.6534 297.00
PAP 8080 P10 3.150 80 3.346 85 3.150 80 0.8681 394.60
PAP 80100 P10 3.150 80 3.346 85 3.937 100 1.0824 492.00
PAP 8560 P10 3.346 85 3.543 90 2.362 60 0.6886 313.00
PAP 85100 P10 3.346 85 3.543 90 3.937 100 1.1550 525.00
PAP 9050 P10 3.543 90 3.740 95 1.969 50 0.6094 277.00
PAP 9060 P10 3.543 90 3.740 95 2.362 60 0.7326 333.00
PAP 90100 P10 3.543 90 3.740 95 3.937 100 1.2122 551.00
PAP 9560 P10 3.740 95 3.937 100 2.362 60 0.7722 351.00
PAP 95100 P10 3.740 95 3.937 100 3.937 100 1.2826 583.00
PAP 10060 P10 3.937 100 4.134 105 2.362 60 0.8536 388.00
PAP 100115 P10 3.937 100 4.134 105 4.528 115 1.6324 742.00
PAP 10560 P10 4.134 105 4.331 110 2.362 60 0.8140 370.00
PAP 105115 P10 4.134 105 4.331 110 4.528 115 1.5664 712.00
PAP 11060 P10 4.331 110 4.528 115 2.362 60 0.9020 410.00
PAP 110115 P10 4.331 110 4.528 115 4.528 115 1.7050 775.00
PAP 11550 P10 4.528 115 4.724 120 1.969 50 0.7700 350.00
PAP 11560 P10 4.528 115 4.724 120 2.362 60 0.8800 400.00
PAP 11570 P10 4.528 115 4.724 120 2.756 70 0.9900 450.00
PAP 12060 P10 4.724 120 4.921 125 2.362 60 0.9570 435.00
PAP 120100 P10 4.724 120 4.921 125 3.937 100 1.6060 730.00
PAP 125100 P10 4.921 125 5.118 130 3.937 100 1.6720 760.00
PAP 13060 P10 5.118 130 5.315 135 2.362 60 1.0340 470.00
PAP 130100 P10 5.118 130 5.315 135 3.937 100 1.7490 795.00
PAP 13560 P10 5.315 135 5.512 140 2.362 60 1.0780 490.00
PAP 13580 P10 5.315 135 5.512 140 3.150 80 1.4344 652.00
PAP 14060 P10 5.512 140 5.709 145 2.362 60 1.1330 515.00
PAP 140100 P10 5.512 140 5.709 145 3.937 100 1.8810 855.00

365
Permaglide Plain Bearings
PAP...P10 SERIES
D Metric dimensions
D Maintenance free
D Steel backing
D Recommended Mounting Tolerances:
Shaft – ID<5:h6, 5"ID<80:f7, 80"ID:h8
Housing bore – OD"5.5:H6, 5.5<OD:H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 15060 P10 5.906 150 6.102 155 2.362 60 1.2100 550.00
PAP 15080 P10 5.906 150 6.102 155 3.150 80 1.6060 730.00
PAP 150100 P10 5.906 150 6.102 155 3.937 100 2.0130 915.00
PAP 16080 P10 6.299 160 6.496 165 3.150 80 1.7072 776.00
PAP 160100 P10 6.299 160 6.496 165 3.937 100 2.1340 970.00
PAP 180100 P10 7.087 180 7.283 185 3.937 100 2.4200 1,100.00
PAP 200100 P10 7.874 200 8.071 205 3.937 100 2.6840 1,220.00
PAP 220100 P10 8.661 220 8.858 225 3.937 100 2.9040 1,320.00
PAP 250100 P10 9.843 250 10.039 255 3.937 100 3.2890 1,495.00
PAP 300100 P10 11.811 300 12.008 305 3.937 100 3.8720 1,760.00

366
Permaglide Plain Bearings
PAP...P11 SERIES
D Metric dimensions
D Maintenance free
D Bronze backing
D Recommended Mounting Tolerances:
Shaft – ID<80:f7, 80"ID:h8
Housing bore – H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 0406 P11 0.157 4 0.236 6 0.236 6 0.0018 0.8
PAP 0505 P11 0.197 5 0.276 7 0.197 5 0.0018 0.8
PAP 0606 P11 0.236 6 0.315 8 0.236 6 0.0024 1.1
PAP 0610 P11 0.236 6 0.315 8 0.394 10 0.0042 1.9
PAP 0808 P11 0.315 8 0.394 10 0.315 8 0.0040 1.8
PAP 0810 P11 0.315 8 0.394 10 0.394 10 0.0048 2.2
PAP 0812 P11 0.315 8 0.394 10 0.472 12 0.0059 2.7
PAP 1005 P11 0.394 10 0.472 12 0.197 5 0.0031 1.4
PAP 1010 P11 0.394 10 0.472 12 0.394 10 0.0059 2.7
PAP 1015 P11 0.394 10 0.472 12 0.591 15 0.0092 4.2
PAP 1020 P11 0.394 10 0.472 12 0.787 20 0.0123 5.6
PAP 1210 P11 0.472 12 0.551 14 0.394 10 0.0073 3.3
PAP 1212 P11 0.472 12 0.551 14 0.472 12 0.0090 4.1
PAP 1215 P11 0.472 12 0.551 14 0.591 15 0.0114 5.2
PAP 1220 P11 0.472 12 0.551 14 0.787 20 0.0152 6.9
PAP 1225 P11 0.472 12 0.551 14 0.984 25 0.0191 8.7
PAP 1415 P11 0.551 14 0.630 16 0.591 15 0.0132 6.0
PAP 1515 P11 0.591 15 0.669 17 0.591 15 0.0150 6.8
PAP 1525 P11 0.591 15 0.669 17 0.984 25 0.0227 10.3
PAP 1615 P11 0.630 16 0.709 18 0.591 15 0.0147 6.7
PAP 1625 P11 0.630 16 0.709 18 0.984 25 0.0242 11.0
PAP 1825 P11 0.709 18 0.787 20 0.984 25 0.0268 12.2
PAP 2015 P11 0.787 20 0.906 23 0.591 15 0.0293 13.3
PAP 2020 P11 0.787 20 0.906 23 0.787 20 0.0374 17.0
PAP 2025 P11 0.787 20 0.906 23 0.984 25 0.0469 21.3
PAP 2030 P11 0.787 20 0.906 23 1.181 30 0.0561 25.5
PAP 2215 P11 0.866 22 0.984 25 0.591 15 0.0345 15.7
PAP 2220 P11 0.866 22 0.984 25 0.787 20 0.0460 20.9
PAP 2225 P11 0.866 22 0.984 25 0.984 25 0.0583 26.5
PAP 2430 P11 0.945 24 1.063 27 1.181 30 0.0750 34.1
PAP 2525 P11 0.984 25 1.102 28 0.984 25 0.0647 29.4
PAP 2530 P11 0.984 25 1.102 28 1.181 30 0.0777 35.3
PAP 2830 P11 1.102 28 1.260 32 1.181 30 0.1012 46.0
PAP 3020 P11 1.181 30 1.339 34 0.787 20 0.0810 36.8
PAP 3030 P11 1.181 30 1.339 34 1.181 30 0.1214 55.2
PAP 3040 P11 1.181 30 1.339 34 1.575 40 0.1628 74.0
PAP 3520 P11 1.378 35 1.535 39 0.787 20 0.0972 44.2
PAP 3530 P11 1.378 35 1.535 39 1.181 30 0.1459 66.3
PAP 4050 P11 1.575 40 1.732 44 1.969 50 0.2609 118.6
PAP 4550 P11 1.772 45 1.969 50 1.969 50 0.4090 185.9
PAP 5030 P11 1.969 50 2.165 55 1.181 30 0.2955 134.3
PAP 5040 P11 1.969 50 2.165 55 1.575 40 0.3938 179.0
PAP 5060 P11 1.969 50 2.165 55 2.362 60 0.5920 269.1
PAP 5540 P11 2.165 55 2.362 60 1.575 40 0.3412 155.1
PAP 6040 P11 2.362 60 2.559 65 1.575 40 0.3705 168.4
PAP 6050 P11 2.362 60 2.559 65 1.969 50 0.4631 210.5

367
Permaglide Plain Bearings
PAP...P11 SERIES
D Metric dimensions
D Maintenance free
D Bronze backing
D Recommended Mounting Tolerances:
Shaft – ID<80:f7, 80"ID:h8
Housing bore – H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 6060 P11 2.362 60 2.559 65 2.362 60 0.5557 252.6
PAP 6070 P11 2.362 60 2.559 65 2.756 70 0.6483 294.7
PAP 7050 P11 2.756 70 2.953 75 1.969 50 0.5379 244.5
PAP 7070 P11 2.756 70 2.953 75 2.756 70 0.7531 342.3
PAP 8060 P11 3.150 80 3.346 85 2.362 60 0.7313 332.4
PAP 80100 P11 3.150 80 3.346 85 3.937 100 1.2188 554.0
PAP 9060 P11 3.543 90 3.740 95 2.362 60 0.7766 353.0
PAP 90100 P11 3.543 90 3.740 95 3.937 100 1.2936 588.0
PAP 9560 P11 3.740 95 3.937 100 2.362 60 0.9460 430.0
PAP 10060 P11 3.937 100 4.134 105 2.362 60 0.9064 412.0
PAP 100115 P11 3.937 100 4.134 105 4.528 115 1.7380 790.0

368
Permaglide
Flanged Plain Bearings
PAF...P10 SERIES
D Maintenance free
D Steel backing
D Recommended Mounting Tolerances:
Shaft – f7
Housing bore – H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD FLANGE FLANGE LENGTH LENGTH FLANGE FLANGE WEIGHT WEIGHT
d1 d1 d2 d2 WALL WALL b b DIA. DIA.
b1 b1 d3 d3
inch mm inch mm inch mm inch mm inch mm lbs g
PAF 06040 P10 0.236 6 0.315 8 0.039 1 0.157 4 0.472 12 0.0019 0.9
PAF 06070 P10 0.236 6 0.315 8 0.039 1 0.276 7 0.472 12 0.0035 1.6
PAF 06080 P10 0.236 6 0.315 8 0.039 1 0.315 8 0.472 12 0.0037 1.7
PAF 08055 P10 0.315 8 0.394 10 0.039 1 0.217 5.5 0.591 15 0.0037 1.7
PAF 08075 P10 0.315 8 0.394 10 0.039 1 0.295 7.5 0.591 15 0.0046 2.1
PAF 08095 P10 0.315 8 0.394 10 0.039 1 0.374 9.5 0.591 15 0.0056 2.5
PAF 10070 P10 0.394 10 0.472 12 0.039 1 0.276 7 0.709 18 0.0055 2.5
PAF 10090 P10 0.394 10 0.472 12 0.039 1 0.354 9 0.709 18 0.0064 2.9
PAF 10120 P10 0.394 10 0.472 12 0.039 1 0.472 12 0.709 18 0.0084 3.8
PAF 10170 P10 0.394 10 0.472 12 0.039 1 0.669 17 0.709 18 0.0118 5.4
PAF 12070 P10 0.472 12 0.551 14 0.039 1 0.276 7 0.787 20 0.0066 3.0
PAF 12090 P10 0.472 12 0.551 14 0.039 1 0.354 9 0.787 20 0.0082 3.7
PAF 12120 P10 0.472 12 0.551 14 0.039 1 0.472 12 0.787 20 0.0103 4.7
PAF 12170 P10 0.472 12 0.551 14 0.039 1 0.669 17 0.787 20 0.0134 6.1
PAF 14120 P10 0.551 14 0.630 16 0.039 1 0.472 12 0.866 22 0.0118 5.4
PAF 14170 P10 0.551 14 0.630 16 0.039 1 0.669 17 0.866 22 0.0156 7.1
PAF 15090 P10 0.591 15 0.669 17 0.039 1 0.354 9 0.906 23 0.0097 4.4
PAF 15120 P10 0.591 15 0.669 17 0.039 1 0.472 12 0.906 23 0.0126 5.7
PAF 15170 P10 0.591 15 0.669 17 0.039 1 0.669 17 0.906 23 0.0170 7.7
PAF 16120 P10 0.630 16 0.709 18 0.039 1 0.472 12 0.945 24 0.0132 6.0
PAF 16170 P10 0.630 16 0.709 18 0.039 1 0.669 17 0.945 24 0.0183 8.3
PAF 18120 P10 0.709 18 0.787 20 0.039 1 0.472 12 1.024 26 0.0147 6.7
PAF 18170 P10 0.709 18 0.787 20 0.039 1 0.669 17 1.024 26 0.0196 8.9
PAF 18220 P10 0.709 18 0.787 20 0.039 1 0.866 22 1.024 26 0.0244 11.1
PAF 20115 P10 0.787 20 0.906 23 0.059 1.5 0.453 11.5 1.181 30 0.0255 11.6
PAF 20165 P10 0.787 20 0.906 23 0.059 1.5 0.650 16.5 1.181 30 0.0332 15.1
PAF 20215 P10 0.787 20 0.906 23 0.059 1.5 0.846 21.5 1.181 30 0.0420 19.1
PAF 25115 P10 0.984 25 1.102 28 0.059 1.5 0.453 11.5 1.378 35 0.0312 14.2
PAF 25165 P10 0.984 25 1.102 28 0.059 1.5 0.650 16.5 1.378 35 0.0418 19.0
PAF 25215 P10 0.984 25 1.102 28 0.059 1.5 0.846 21.5 1.378 35 0.0526 23.9
PAF 30160 P10 1.181 30 1.339 34 0.079 2 0.630 16 1.654 42 0.0680 30.9
PAF 30260 P10 1.181 30 1.339 34 0.079 2 1.024 26 1.654 42 0.1014 46.1
PAF 35160 P10 1.378 35 1.535 39 0.079 2 0.630 16 1.850 47 0.0779 35.4
PAF 35260 P10 1.378 35 1.535 39 0.079 2 1.024 26 1.850 47 0.1159 52.7
PAF 40260 P10 1.575 40 1.732 44 0.079 2 1.024 26 2.087 53 0.1320 60.0

369
Permaglide
Flanged Plain Bearings
PAF...P11 SERIES
D Maintenance free
D Bronze backing
D Recommended Mounting Tolerances:
Shaft – f7
Housing bore – H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD FLANGE FLANGE LENGTH LENGTH FLANGE FLANGE WEIGHT WEIGHT
d1 d1 d2 d2 WALL WALL b b DIA. DIA.
b1 b1 d3 d3
inch mm inch mm inch mm inch mm inch mm lbs g
PAF 06080 P11 0.236 6 0.315 8 0.039 1 0.315 8 0.472 12 0.0037 1.7
PAF 08055 P11 0.315 8 0.394 10 0.039 1 0.217 5.5 0.591 15 0.0037 1.7
PAF 08095 P11 0.315 8 0.394 10 0.039 1 0.374 9.5 0.591 15 0.0056 2.5
PAF 10070 P11 0.394 10 0.472 12 0.039 1 0.276 7 0.709 18 0.0055 2.5
PAF 10120 P11 0.394 10 0.472 12 0.039 1 0.472 12 0.709 18 0.0084 3.8
PAF 10170 P11 0.394 10 0.472 12 0.039 1 0.669 17 0.709 18 0.0118 5.4
PAF 12070 P11 0.472 12 0.551 14 0.039 1 0.276 7 0.787 20 0.0066 3.0
PAF 12090 P11 0.472 12 0.551 14 0.039 1 0.354 9 0.787 20 0.0082 3.7
PAF 12120 P11 0.472 12 0.551 14 0.039 1 0.472 12 0.787 20 0.0103 4.7
PAF 15120 P11 0.591 15 0.669 17 0.039 1 0.472 12 0.906 23 0.0126 5.7
PAF 15170 P11 0.591 15 0.669 17 0.039 1 0.669 17 0.906 23 0.0170 7.7
PAF 16120 P11 0.630 16 0.709 18 0.039 1 0.472 12 0.945 24 0.0132 6.0
PAF 18100 P11 0.709 18 0.787 20 0.039 1 0.394 10 1.024 26 0.0110 5.0
PAF 18220 P11 0.709 18 0.787 20 0.039 1 0.866 22 1.024 26 0.0244 11.1
PAF 20115 P11 0.787 20 0.906 23 0.059 1.5 0.453 11.5 1.181 30 0.0256 11.6
PAF 20165 P11 0.787 20 0.906 23 0.059 1.5 0.650 16.5 1.181 30 0.0333 15.1
PAF 25215 P11 0.984 25 1.102 28 0.059 1.5 0.846 21.5 1.378 35 0.0526 23.9
PAF 30160 P11 1.181 30 1.339 34 0.079 2 0.630 16 1.654 42 0.0681 30.9
PAF 30260 P11 1.181 30 1.339 34 0.079 2 1.024 26 1.654 42 0.1015 46.1
PAF 35260 P11 1.378 35 1.535 39 0.079 2 1.024 26 1.850 47 0.1161 52.7
PAF 40260 P11 1.575 40 1.732 44 0.079 2 1.024 26 2.087 53 0.1300 59.0

370
Permaglide Thrust Washers
PAW...P10 SERIES
D Maintenance free
D Steel backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD WALL WALL WEIGHT WEIGHT
d4 d4 d5 d5 s3 s3
inch mm inch mm inch mm lbs g
PAW 10 P10 0.394 10 0.787 20 0.059 1.5 0.0057 2.6
PAW 12 P10 0.472 12 0.945 24 0.059. 1.5 0.0084 3.8
PAW 14 P10 0.551 14 1.024 26 0.059 1.5 0.0088 4.0
PAW 16 P10 0.630 16 1.181 30 0.059 1.5 0.0121 5.5
PAW 18 P10 0.709 18 1.260 32 0.059 1.5 0.0132 6.0
PAW 20 P10 0.787 20 1.417 36 0.059 1.5 0.0176 8.0
PAW 22 P10 0.866 22 1.496 38 0.059 1.5 0.0187 8.5
PAW 26 P10 1.024 26 1.732 44 0.059 1.5 0.0244 11.1
PAW 28 P10 1.102 28 1.890 48 0.059 1.5 0.0293 13.3
PAW 32 P10 1.260 32 2.126 54 0.059 1.5 0.0359 16.3
PAW 38 P10 1.496 38 2.441 62 0.059 1.5 0.0462 21.0
PAW 42 P10 1.654 42 2.598 66 0.059 1.5 0.0484 22.0
PAW 48 P10 1.890 48 2.913 74 0.079 2 0.0810 36.8
PAW 52 P10 2.047 52 3.071 78 0.079 2 0.0854 38.8
PAW 62 P10 2.441 62 3.543 90 0.079 2 0.1074 48.8

371
Permaglide Strips
PAS...P10 SERIES
D Maintenance free
D Steel backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER WALL WALL WIDTH WIDTH USABLE USABLE LENGTH LENGTH WEIGHT WEIGHT
s3 s3 B B WIDTH WIDTH L L
B1 B1
inch mm inch mm inch mm inch mm lbs g
PAS 05180 P10 0.020 0.5 7.087 180 6.614 168 19.685 500 0.726 330
PAS 07180 P10 0.030 0.75 7.087 180 6.614 168 19.685 500 1.093 497
PAS 10250 P10 0.039 1 9.843 250 9.370 238 19.685 500 2.066 939
PAS 15250 P10 0.059 1.5 9.843 250 9.370 238 19.685 500 3.126 1421
PAS 20250 P10 0.079 2 9.843 250 9.370 238 19.685 500 4.211 1914
PAS 25250 P10 0.098 2.5 9.843 250 9.370 238 19.685 500 5.262 2392
PAS 30250 P10 0.120 3.06 9.843 250 9.370 238 19.685 500 6.468 2940

372
Permaglide Strips
PAS...P11 SERIES
D Maintenance free
D Bronze backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER WALL WALL WIDTH WIDTH USABLE USABLE LENGTH LENGTH WEIGHT WEIGHT
s3 s3 B B WIDTH WIDTH L L
B1 B1
inch mm inch mm inch mm inch mm lbs g
PAS 10160 P11 0.039 1 6.299 160 5.827 148 19.685 500 1.459 663
PAS 15180 P11 0.059 1.5 7.087 180 6.614 168 19.685 500 2.488 1131
PAS 20180 P11 0.079 2 7.087 180 6.614 168 19.685 500 3.351 1523
PAS 25180 P11 0.098 2.5 7.087 180 6.614 168 19.685 500 4.213 1915

373
Permaglide Plain Bearings
PAP...P20 SERIES
D Low maintenance
D Steel backing
D Recommended Mounting Tolerances:
Shaft – h8
Housing bore – H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 0808 P20 0.315 8 0.394 10 0.315 8 0.0035 1.60
PAP 0810 P20 0.315 8 0.394 10 0.394 10 0.0044 2.00
PAP 0812 P20 0.315 8 0.394 10 0.472 12 0.0053 2.40
PAP 1008 P20 0.394 10 0.472 12 0.315 8 0.0040 1.80
PAP 1010 P20 0.394 10 0.472 12 0.394 10 0.0051 2.30
PAP 1015 P20 0.394 10 0.472 12 0.591 15 0.0077 3.50
PAP 1210 P20 0.472 12 0.551 14 0.394 10 0.0066 3.00
PAP 1212 P20 0.472 12 0.551 14 0.472 12 0.0077 3.50
PAP 1215 P20 0.472 12 0.551 14 0.591 15 0.0097 4.40
PAP 1220 P20 0.472 12 0.551 14 0.787 20 0.0132 6.00
PAP 1420 P20 0.551 14 0.630 16 0.787 20 0.0147 6.70
PAP 1510 P20 0.591 15 0.669 17 0.394 10 0.0077 3.50
PAP 1515 P20 0.591 15 0.669 17 0.591 15 0.0117 5.30
PAP 1525 P20 0.591 15 0.669 17 0.984 25 0.0194 8.80
PAP 1612 P20 0.630 16 0.709 18 0.472 12 0.0099 4.50
PAP 1615 P20 0.630 16 0.709 18 0.591 15 0.0123 5.60
PAP 1620 P20 0.630 16 0.709 18 0.787 20 0.0165 7.50
PAP 1815 P20 0.709 18 0.787 20 0.591 15 0.0139 6.30
PAP 1820 P20 0.709 18 0.787 20 0.787 20 0.0187 8.50
PAP 2015 P20 0.787 20 0.906 23 0.591 15 0.0231 10.50
PAP 2020 P20 0.787 20 0.906 23 0.787 20 0.0308 14.00
PAP 2025 P20 0.787 20 0.906 23 0.984 25 0.0385 17.50
PAP 2030 P20 0.787 20 0.906 23 1.181 30 0.0506 23.00
PAP 2220 P20 0.866 22 0.984 25 0.787 20 0.0339 15.40
PAP 2420 P20 0.945 24 1.063 27 0.787 20 0.0396 18.00
PAP 2515 P20 0.984 25 1.102 28 0.591 15 0.0312 14.20
PAP 2520 P20 0.984 25 1.102 28 0.787 20 0.0418 19.00
PAP 2525 P20 0.984 25 1.102 28 0.984 25 0.0484 22.00
PAP 2530 P20 0.984 25 1.102 28 1.181 30 0.0581 26.40
PAP 2830 P20 1.102 28 1.260 32 1.181 30 0.0880 40.00
PAP 3020 P20 1.181 30 1.339 34 0.787 20 0.0629 28.60
PAP 3025 P20 1.181 30 1.339 34 0.984 25 0.0788 35.80
PAP 3030 P20 1.181 30 1.339 34 1.181 30 0.0944 42.90
PAP 3040 P20 1.181 30 1.339 34 1.575 40 0.1258 57.20
PAP 3230 P20 1.260 32 1.417 36 1.181 30 0.1056 48.00
PAP 3520 P20 1.378 35 1.535 39 0.787 20 0.0717 32.60
PAP 3530 P20 1.378 35 1.535 39 1.181 30 0.1078 49.00
PAP 3550 P20 1.378 35 1.535 39 1.969 50 0.1936 88.00
PAP 4020 P20 1.575 40 1.732 44 0.787 20 0.0821 37.30
PAP 4030 P20 1.575 40 1.732 44 1.181 30 0.1232 56.00
PAP 4040 P20 1.575 40 1.732 44 1.575 40 0.1643 74.70
PAP 4050 P20 1.575 40 1.732 44 1.969 50 0.2053 93.30
PAP 4550 P20 1.772 45 1.969 50 1.969 50 0.2922 132.80
PAP 5025 P20 1.969 50 2.165 55 0.984 25 0.1716 78.00
PAP 5040 P20 1.969 50 2.165 55 1.575 40 0.2587 117.60
PAP 5060 P20 1.969 50 2.165 55 2.362 60 0.3881 176.40

374
Permaglide Plain Bearings
PAP...P20 SERIES
D Low maintenance
D Steel backing
D Recommended Mounting Tolerances:
Shaft – h8
Housing bore – H7

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD LENGTH LENGTH WEIGHT WEIGHT
d1 d1 d2 d2 b b
inch mm inch mm inch mm lbs g
PAP 5540 P20 2.165 55 2.362 60 1.575 40 0.3014 137.00
PAP 6030 P20 2.362 60 2.559 65 1.181 30 0.2297 104.40
PAP 6040 P20 2.362 60 2.559 65 1.575 40 0.3062 139.20
PAP 6060 P20 2.362 60 2.559 65 2.362 60 0.4594 208.80
PAP 7050 P20 2.756 70 2.953 75 1.969 50 0.4440 201.80
PAP 7070 P20 2.756 70 2.953 75 2.756 70 0.6666 303.00
PAP 7540 P20 2.953 75 3.150 80 1.575 40 0.4048 184.00
PAP 7580 P20 2.953 75 3.150 80 3.150 80 0.8140 370.00
PAP 8040 P20 3.150 80 3.346 85 1.575 40 0.4041 183.70
PAP 8060 P20 3.150 80 3.346 85 2.362 60 0.6072 276.00
PAP 8080 P20 3.150 80 3.346 85 3.150 80 0.8083 367.40
PAP 9060 P20 3.543 90 3.740 95 2.362 60 0.6809 309.50
PAP 10050 P20 3.937 100 4.134 105 1.969 50 0.6279 285.40
PAP 10060 P20 3.937 100 4.134 105 2.362 60 0.7535 342.50

375
Permaglide Thrust Washers
PAW...P20 SERIES
D Low maintenance
D Steel backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD WALL WALL WEIGHT WEIGHT
d4 d4 d5 d5 s3 s3
inch mm inch mm inch mm lbs g
PAW 12 P20 0.472 12 0.945 24 0.020 1.5 0.0077 3.5
PAW 14 P20 0.551 14 1.024 26 0.059 1.5 0.0081 3.7
PAW 18 P20 0.709 18 1.260 32 0.059 1.5 0.0123 5.6
PAW 20 P20 0.787 20 1.417 36 0.059 1.5 0.0163 7.4
PAW 22 P20 0.866 22 1.496 38 0.059 1.5 0.0174 7.9
PAW 26 P20 1.023 26 1.732 44 0.059 1.5 0.0227 10.3
PAW 28 P20 1.1024 28 1.890 48 0.059 1.5 0.0273 12.4
PAW 32 P20 1.260 32 2.126 54 0.059 1.5 0.0334 15.2
PAW 38 P20 1.496 38 2.441 62 0.059 1.5 0.0429 19.5
PAW 42 P20 1.654 42 2.598 66 0.059 1.5 0.0458 20.8
PAW 48 P20 1.890 48 2.913 74 0.079 2.0 0.0768 34.9
PAW 52 P20 2.047 52 3.071 78 0.079 2.0 0.0794 36.1

376
Permaglide Strips
PAS...P20 SERIES
D Low maintenance
D Steel backing

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER WALL WALL WIDTH WIDTH USABLE USABLE LENGTH LENGTH WEIGHT WEIGHT
s3 s3 B B WIDTH WIDTH L L
B1 B1
inch mm inch mm inch mm inch mm lbs g
PAS 10180 P20 0.039 0.99 7.087 180 6.614 168 19.685 500 1.408 640
PAS 15180 P20 0.058 1.48 7.087 180 6.614 168 19.685 500 2.092 951
PAS 20180 P20 0.078 1.97 7.087 180 6.614 168 19.685 500 2.818 1281
PAS 25180 P20 0.097 2.46 7.087 180 6.614 168 19.685 500 3.524 1602

377
Permaglide Strips
PAS...P21 SERIES
D Low maintenance
D Steel backing
D Machining allowance with lubrication pockets

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER WALL WALL WIDTH WIDTH USABLE USABLE LENGTH LENGTH WEIGHT WEIGHT
s3 s3 B B WIDTH WIDTH L L
B1 B1
inch mm inch mm inch mm inch mm lbs g
PAS 10180 P21 0.044 1.11 7.087 180 6.614 168 19.685 500 1.564 711
PAS 15180 P21 0.063 1.61 7.087 180 6.614 168 19.685 500 2.178 990
PAS 20180 P21 0.083 2.11 7.087 180 6.614 168 19.685 500 2.904 1320
PAS 25180 P21 0.104 2.63 7.087 180 6.614 168 19.685 500 3.610 1641

378
Permaglide Strips
PAS...P22 SERIES
D Low maintenance
D Steel backing
D Machining allowance without lubrication pockets

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER WALL WALL WIDTH WIDTH USABLE USABLE LENGTH LENGTH WEIGHT WEIGHT
s3 s3 B B WIDTH WIDTH L L
B1 B1
inch mm inch mm inch mm inch mm lbs g
PAS 10180 P22 0.044 1.11 7.087 180 6.614 168 19.685 500 1.564 711
PAS 15180 P22 0.063 1.61 7.087 180 6.614 168 19.685 500 2.178 990
PAS 20180 P22 0.083 2.11 7.087 180 6.614 168 19.685 500 2.904 1320
PAS 25180 P22 0.104 2.63 7.087 180 6.614 168 19.685 500 3.610 1641

379
Elges
Radial Spherical Plain Bearings
GE..DO, GE..DO-2RS SERIES
D Sliding contact surfaces: steel/steel
D Hardened inner and outer ring
D GE..DO 6-300 outer ring with single axial split
D GE..DO 320-1000 outer ring double split axially shipped with
retaining rings

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART SHAFT SHAFT OD OD WIDTH WIDTH WIDTH WIDTH BALL BALL ANGLE WEIGHT WEIGHT DYN. DYN. STAT. STAT.
NUMBER d d D D B B C C DIA. DIA. alpha CAP. CAP. CAP. CAP.
dK dK x1000 x1000
inch mm inch mm inch mm inch mm inch mm deg lbs kg lbf kN lbf kN
GE6DO 0.236 6 0.551 14 0.236 6 0.157 4 0.394 10 13 0.009 0.004 0.760 3.4 3.80 17
GE8DO 0.315 8 0.63 16 0.315 8 0.197 5 0.512 13 15 0.015 0.007 1.240 5.5 6.20 27.5
GE10DO 0.394 10 0.748 19 0.354 9 0.236 6 0.63 16 12 0.024 0.011 1.830 8.15 9.10 40.5
GE12DO 0.472 12 0.866 22 0.394 10 0.276 7 0.709 18 11 0.035 0.016 2.430 10.8 12.10 54
GE15DO 0.591 15 1.024 26 0.472 12 0.354 9 0.866 22 8 0.055 0.025 3.800 17 19.10 85
GE16DO 0.63 16 1.181 30 0.551 14 0.394 10 0.984 25 10 0.084 0.038 4.750 21.2 23.80 106
GE17DO 0.669 17 1.181 30 0.551 14 0.394 10 0.984 25 10 0.090 0.041 4.750 21.2 23.80 106
GE17DO2RS 0.669 17 1.181 30 0.551 14 0.394 10 0.984 25 10 0.090 0.041 4.75 21.2 23.80 106
GE20DO 0.787 20 1.378 35 0.63 16 0.472 12 1.142 29 9 0.135 0.061 6.700 30 33 146
GE20DO2RS 0.787 20 1.378 35 0.63 16 0.472 12 1.142 29 9 0.135 0.061 6.70 30 33.00 146
GE25DO 0.984 25 1.654 42 0.787 20 0.63 16 1.398 35.5 7 0.243 0.110 10.80 48 54 240
GE25DO2RS 0.984 25 1.654 42 0.787 20 0.63 16 1.398 35.5 7 0.243 0.110 10.80 48 54 240
GE30DO 1.181 30 1.85 47 0.866 22 0.709 18 1.602 40.7 6 0.309 0.140 13.90 62 70 310
GE30DO2RS 1.181 30 1.85 47 0.866 22 0.709 18 1.602 40.7 6 0.309 0.140 13.90 62 70 310
GE35DO 1.378 35 2.165 55 0.984 25 0.787 20 1.85 47 6 0.485 0.220 18.00 80 90 400
GE35DO2RS 1.378 35 2.165 55 0.984 25 0.787 20 1.85 47 6 0.485 0.220 18.00 80 90 400
GE40DO 1.575 40 2.441 62 1.102 28 0.866 22 2.087 53 7 0.662 0.300 22.50 100 112 500
GE40DO2RS 1.575 40 2.441 62 1.102 28 0.866 22 2.087 53 7 0.662 0.300 22.50 100 112 500
GE45DO 1.772 45 2.677 68 1.26 32 0.984 25 2.362 60 7 0.882 0.400 28.50 127 144 640
GE45DO2RS 1.772 45 2.677 68 1.26 32 0.984 25 2.362 60 7 0.882 0.400 28.50 127 144 640
GE50DO 1.969 50 2.953 75 1.378 35 1.102 28 2.598 66 6 1.191 0.540 35 156 175 780
GE50DO2RS 1.969 50 2.953 75 1.378 35 1.102 28 2.598 66 6 1.191 0.540 35 156 175 780
GE60DO 2.362 60 3.543 90 1.732 44 1.417 36 3.15 80 6 2.205 1.000 55 245 275 1220
GE60DO2RS 2.362 60 3.543 90 1.732 44 1.417 36 3.15 80 6 2.205 1.000 55 245 275 1220
GE70DO 2.756 70 4.134 105 1.929 49 1.575 40 3.622 92 6 3.308 1.500 71 315 350 1560
GE70DO2RS 2.756 70 4.134 105 1.929 49 1.575 40 3.622 92 6 3.308 1.500 71 315 350 1560
GE80D2RS 3.15 80 4.724 120 2.165 55 1.772 45 4.134 105 6 4.851 2.200 90 400 450 2000
GE80DO 3.15 80 4.724 120 2.165 55 1.772 45 4.134 105 6 4.851 2.200 90 400 450 2000
GE90DO 3.543 90 5.118 130 2.362 60 1.969 50 4.528 115 5 5.95 2.700 110 490 550 2450
GE90DO2RS 3.543 90 5.118 130 2.362 60 1.969 50 4.528 115 5 5.954 2.700 110 490 550 2450
GE100DO 3.937 100 5.906 150 2.756 70 2.165 55 5.118 130 7 9.48 4.300 137 610 690 3050
GE100DO2RS 3.937 100 5.906 150 2.756 70 2.165 55 5.118 130 7 9.482 4.300 137 610 690 3050
GE110DO 4.331 110 6.299 160 2.756 70 2.165 55 5.512 140 6 10.36 4.700 147 655 730 3250
GE110DO2RS 4.331 110 6.299 160 2.756 70 2.165 55 5.512 140 6 10.36 4.70 147 655 730 3250
GE120DO 4.724 120 7.087 180 3.346 85 2.756 70 6.299 160 6 17.64 8.00 214 950 1070 4750
GE120DO2RS 4.724 120 7.087 180 3.346 85 2.756 70 6.299 160 6 17.64 8.00 214 950 1070 4750
GE140DO 5.512 140 8.268 210 3.543 90 2.756 70 7.087 180 7 24.26 11.00 243 1080 1210 5400
GE140DO2RS 5.512 140 8.268 210 3.543 90 2.756 70 7.087 180 7 24.26 11.00 243 1080 1210 5400
GE160DO 6.299 160 9.055 230 4.134 105 3.15 80 7.874 200 8 29.77 13.50 310 1370 1530 6800
GE160DO2RS 6.299 160 9.055 230 4.134 105 3.15 80 7.874 200 8 29.77 13.50 310 1370 1530 6800
GE180DO 7.087 180 10.236 260 4.134 105 3.15 80 8.858 225 6 40.79 18.50 345 1530 1720 7650
GE180DO2RS 7.087 180 10.236 260 4.134 105 3.15 80 8.858 225 6 40.79 18.50 345 1530 1720 7650
GE200DO 7.874 200 11.417 290 5.118 130 3.937 100 9.843 250 7 61.74 28 475 2120 2380 10600
GE200DO2RS 7.874 200 11.417 290 5.118 130 3.937 100 9.843 250 7 61.74 28.00 475 2120 2380 10600
GE220DO2RS 8.661 220 12.598 320 5.315 135 3.937 100 10.827 275 8 78.28 35.50 520 2320 2600 11600
GE240DO2RS 9.449 240 13.386 340 5.512 140 3.937 100 11.811 300 8 88.20 40 570 2550 2850 12700

380
Elges
Radial Spherical Plain Bearings
GE..DO, GE..DO-2RS SERIES
D Sliding contact surfaces: steel/steel
D Hardened inner and outer ring
D GE..DO 6-300 outer ring with single axial split
D GE..DO 320-1000 outer ring double split axially shipped with
retaining rings

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART SHAFT SHAFT OD OD WIDTH WIDTH WIDTH WIDTH BALL BALL ANGLE WEIGHT WEIGHT DYN. DYN. STAT. STAT.
NUMBER d d D D B B C C DIA. DIA. alpha CAP. CAP. CAP. CAP.
dK dK x1000 x1000
inch mm inch mm inch mm inch mm inch mm deg lbs kg lbf kN lbf kN
GE260DO2RS 10.236 260 14.567 370 5.906 150 4.331 110 12.795 325 7 110 50 690 3050 3450 15300
GE280DO2RS 11.024 280 15.748 400 6.102 155 4.724 120 13.78 350 6 141 64 800 3550 4050 18000
GE300DO2RS 11.811 300 16.929 430 6.496 165 4.724 120 14.764 375 7 165 75 850 3800 4250 19000
GE320DO 12.598 320 17.323 440 6.299 160 5.315 135 14.961 380 4 170 77 990 4400 4950 22000
GE340DO 13.386 340 18.11 460 6.299 160 5.315 135 15.748 400 3.8 181 82 1,050 4650 5200 23200
GE360DO 14.173 360 18.898 480 6.299 160 5.315 135 16.535 420 3.6 194 88 1,080 4800 5400 24000
GE380DO 14.961 380 20.472 520 7.48 190 6.299 160 17.717 450 4.1 280 127 1,420 6300 7100 31500
GE400DO 15.748 400 21.26 540 7.48 190 6.299 160 18.504 470 3.9 291 132 1,470 6550 7300 32500
GE420DO 16.535 420 22.047 560 7.48 190 6.299 160 19.291 490 3.7 320 145 1,530 6800 7800 34500
GE440DO 17.323 440 23.622 600 8.583 218 7.283 185 20.472 520 3.9 419 190 1,940 8650 9500 42300
GE460DO 18.11 460 24.409 620 8.583 218 7.283 185 21.26 540 3.7 441 200 2,020 9000 10100 45000
GE480DO 18.898 480 25.591 650 9.055 230 7.677 195 22.244 565 3.8 523 237 2,200 9800 11000 49000
GE500DO 19.685 500 26.378 670 9.055 230 7.677 195 23.031 585 3.6 538 244 2,290 10200 11500 51000
GE530DO 20.866 530 27.953 710 9.567 243 8.071 205 24.409 620 3.7 639 290 2,550 11400 12800 57000
GE560DO 22.047 560 29.528 750 10.157 258 8.465 215 25.787 655 4 750 340 2,850 12700 14400 64000
GE600DO 23.622 600 31.496 800 10.709 272 9.055 230 27.559 700 3.6 902 409 3,300 14600 16500 73500
GE630DO 24.803 630 33.465 850 11.811 300 10.236 260 29.134 740 3.3 1160 526 3,950 17600 19800 88000
GE670DO 26.378 670 35.433 900 12.126 308 10.236 260 30.906 785 337 1314 596 4,250 19000 21400 95000
GE710DO 27.953 710 37.402 950 12.795 325 10.827 275 32.677 830 3.7 1528 693 4,750 21200 15870 70600
GE750DO 29.528 750 39.37 1000 13.189 335 11.024 280 34.449 875 3.8 1729 784 5,100 22800 25600 114000
GE800DO 31.496 800 41.732 1060 13.976 355 11.811 300 36.614 930 3.6 2040 925 5,800 26000 29000 129000
GE850DO 33.465 850 44.094 1120 14.37 365 12.205 310 38.78 985 3.4 2326 1055 6,400 28500 32100 143000
GE900DO 35.433 900 46.457 1180 14.764 375 12.598 320 40.945 1040 3.2 2624 1190 7,000 31000 35100 156000
GE950DO 37.402 950 49.213 1250 15.748 400 13.386 340 43.307 1100 3.3 3140 1424 8,000 35500 39600 176000
GE1000DO 39.37 1000 51.969 1320 17.244 438 14.567 370 45.669 1160 3.5 3870 1755 9,100 40500 45900 204000

381
Elges
Radial Spherical Plain Bearings
GE..FO, GE..FO-2RS SERIES
D Sliding contact surfaces: steel/steel
D Hardened inner and outer ring
D Wide inner ring with increased tilting angle
D Outer ring with single (axial) split

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART SHAFT SHAFT OD OD WIDTH WIDTH WIDTH WIDTH BALL BALL ANGLE WEIGHT WEIGHT DYN. DYN. STAT. STAT.
NUMBER d d D D B B C C DIA. DIA. alpha CAP. CAP. CAP. CAP.
dK dK x1000 x1000
inch mm inch mm inch mm inch mm inch mm deg lbs kg lbf kN lbf kN
GE6FO 0.236 6 0.630 16 0.354 9 0.197 5 0.512 13 21 0.018 0.008 1.24 5.5 6.20 27.5
GE8FO 0.315 8 0.748 19 0.433 11 0.236 6 0.630 16 21 0.031 0.014 1.83 8.15 9.10 40.5
GE10FO 0.394 10 0.866 22 0.472 12 0.276 7 0.709 18 18 0.044 0.020 2.43 10.8 12.10 54
GE12FO 0.472 12 1.024 26 0.591 15 0.354 9 0.866 22 18 0.075 0.034 3.80 17 19.10 85
GE15FO2RS 0.591 15 1.181 30 0.630 16 0.394 10 0.984 25 16 0.101 0.046 4.75 21.2 23.80 106
GE17FO2RS 0.669 17 1.378 35 0.787 20 0.472 12 1.142 29 19 0.172 0.078 6.70 30 33 146
GE20FO2RS 0.787 20 1.654 42 0.984 25 0.630 16 1.398 35.5 17 0.331 0.150 10.80 48 54 240
GE25FO2RS 1.378 25 1.850 47 1.102 28 0.709 18 1.602 40.7 17 0.419 0.190 13.90 62 70 310
GE30FO2RS 1.181 30 2.165 55 1.260 32 0.787 20 1.850 47 17 0.639 0.290 18.00 80 90 400
GE35FO2RS 1.378 35 2.441 62 1.378 35 0.866 22 2.087 53 16 0.860 0.390 22.50 100 112 500
GE40FO2RS 1.575 40 2.677 68 1.575 40 0.984 25 2.362 60 17 1.147 0.520 28.50 127 144 640
GE45FO2RS 1.772 45 2.953 75 1.693 43 1.102 28 2.598 66 15 1.499 0.680 35 156 175 780
GE50FO2RS 1.969 50 3.543 90 2.205 56 1.417 36 3.150 80 17 3.087 1.400 55 245 275 1220
GE60FO2RS 2.362 60 4.134 105 2.480 63 1.575 40 3.622 92 17 4.410 2.000 71 315 350 1560
GE70FO2RS 2.756 70 4.724 120 2.756 70 1.772 45 4.134 105 16 6.395 2.900 90 400 450 2000
GE80FO2RS 3.150 80 5.118 130 2.953 75 1.969 50 4.528 115 14 7.718 3.500 110 490 550 2450
GE90FO2RS 3.543 90 5.906 150 3.347 85 2.165 55 5.118 130 15 11.907 5.400 137 610 690 3050
GE100FO2RS 3.937 100 6.299 160 3.347 85 2.165 55 5.512 140 14 13.010 5.900 147 655 730 3250
GE110FO2RS 4.331 110 7.087 180 3.937 100 2.756 70 6.299 160 12 21.389 9.700 214 950 1070 4750
GE120FO2RS 4.724 120 8.268 210 4.528 115 2.756 70 7.087 180 16 33.075 15 243 1080 1210 5400
GE140FO2RS 5.512 140 9.055 230 5.118 130 3.150 80 7.874 200 16 40.793 19 310 1370 1530 6800
GE160FO2RS 6.299 160 10.236 260 5.315 135 3.150 80 8.858 225 16 55.125 25 345 1530 1720 7650
GE180FO2RS 7.087 180 11.417 290 6.102 155 3.937 100 9.843 250 14 78.278 36 475 2120 2380 10600
GE200FO2RS 7.874 200 12.598 320 6.496 165 3.937 100 10.827 275 15 99.225 45 520 2320 2600 11600
GE220FO2RS 8.661 220 13.386 340 6.890 175 3.937 100 11.811 300 16 112.455 51 570 2550 2850 12700
GE240FO2RS 9.449 240 14.567 370 7.480 190 4.331 110 12.795 325 15 141.120 64 690 3050 3450 15300
GE260FO2RS 10.236 260 15.748 400 8.071 205 4.724 120 13.780 350 15 178.605 81 800 3550 4050 18000
GE280FO2RS 11.024 280 16.929 430 8.268 210 4.724 120 14.764 375 15 207.270 94 850 3800 4250 19000

382
Elges
Radial Spherical Plain Bearings
GE..PB SERIES
D DIN 648, dimension series K
D Sliding contact surfaces: steel/bronze

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C dk dk ALPHA C C C0 C0 WGT. WGT
NUMBER inch mm inch mm inch mm inch mm inch mm deg lbf kN lbf kN lbs kg
GE5PB 0.197 5 0.512 13 0.315 8 0.236 6 0.438 11.112 13 730 3.25 1,910 8.5 0.013 0.006
GE6PB 0.236 6 0.630 16 0.354 9 0.266 6.75 0.500 12.7 13 970 4.3 2,430 10.8 0.022 0.01
GE8PB 0.315 8 0.748 19 0.472 12 0.354 9 0.625 15.875 14 1,620 7.2 4,050 18 0.04 0.018
GE10PB 0.394 10 0.866 22 0.551 14 0.413 10.5 0.750 19.05 13 2,250 10 5,600 25 0.06 0.027
GE12PB 0.472 12 1.024 26 0.630 16 0.472 12 0.875 22.225 13 3,000 13.4 7,500 33.5 0.095 0.043
GE14PB 0.551 14 1.102 28 0.748 19 0.532 13.5 1.000 25.4 16 3,800 17 9,700 43 0.121 0.055
GE16PB 0.630 16 1.260 32 0.827 21 0.591 15 1.125 28.575 15 4,850 21.6 12,100 54 0.176 0.08
GE18PB 0.709 18 1.378 35 0.906 23 0.650 16.5 1.250 31.75 15 5,800 26 14,700 65.5 0.221 0.1
GE20PB 0.787 20 1.575 40 0.984 25 0.709 18 1.375 34.925 14 7,100 31.5 18,000 80 0.331 0.15
GE22PB 0.866 22 1.654 42 1.102 28 0.787 20 1.500 38.1 15 8,500 38 21,700 96.5 0.397 0.18
GE25PB 0.984 25 1.850 47 1.221 31 0.866 22 1.687 42.85 15 10,700 47.5 26,500 118 0.529 0.24
GE30PB 1.181 30 2.165 55 1.457 37 0.984 25 2.000 50.8 17 14,400 64 36,000 160 0.838 0.38

383
Elges
Radial Spherical Plain Bearings
GE..LO SERIES
D DIN 648, dimension series EW – ISO 6124/2
D Sliding contact surfaces: steel/steel

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C
NUMBER inch mm inch mm inch mm inch mm
GE12LO 0.472 12 0.866 22 0.472 12 0.276 7
GE16LO 0.630 16 1.102 28 0.630 16 0.354 9
GE20LO 0.787 20 1.378 35 0.787 20 0.472 12
GE25LO 0.984 25 1.654 42 0.984 25 0.630 16
GE32LO 1.260 32 2.047 52 1.260 32 0.709 18
GE40LO 1.575 40 2.441 62 1.575 40 0.866 22
GE50LO 1.969 50 2.953 75 1.969 50 1.102 28
GE63LO 2.480 63 3.740 95 2.480 63 1.417 36
GE70LO 2.756 70 4.134 105 2.756 70 1.575 40
GE80LO 3.150 80 4.724 120 3.150 80 1.772 45
GE90LO 3.543 90 5.118 130 3.543 90 1.969 50
GE100LO 3.937 100 5.906 150 3.937 100 2.165 55
GE110LO 4.331 110 6.299 160 4.331 110 2.165 55
GE125LO 4.921 125 7.087 180 4.921 125 2.756 70
GE160LO 6.299 160 9.055 230 6.299 160 3.150 80
GE200LO 7.874 200 11.417 290 7.874 200 3.937 100
GE250LO 9.843 250 15.748 400 9.843 250 4.724 120
GE320LO 12.598 320 20.472 520 12.598 320 6.299 160

CONTINUED FROM ABOVE

PART dk dk d2 d2 WGT. WGT ALPHA C C C0 C0
NUMBER inch mm inch mm lbs kg deg lbf kN lbf kN
GE12LO 0.709 18 0.610 15.5 0.044 0.02 4 2,430 10.8 12,100 54
GE16LO 0.906 23 0.787 20 0.066 0.03 4 3,950 17.6 19,800 88
GE20LO 1.142 29 0.984 25 0.154 0.07 4 6,700 30 33,000 146
GE25LO 1.398 35.5 1.181 30 0.265 0.12 4 10,800 48 54,000 240
GE32LO 1.732 44 1.496 38 0.441 0.2 4 15,100 67 75,000 335
GE40LO 2.087 53 1.811 46 0.75 0.34 4 22,500 100 112,000 500
GE50LO 2.598 66 2.244 57 1.235 0.56 4 35,000 156 175,000 780
GE63LO 3.268 83 2.815 71.5 2.646 1.2 4 57,000 255 285,000 1270
GE70LO 3.622 92 3.110 79 3.749 1.7 4 71,000 315 350,000 1560
GE80LO 4.134 105 3.583 91 5.292 2.4 4 90,000 400 450,000 2000
GE90LO 4.528 115 3.898 99 7.056 3.2 4 110,000 490 550,000 2450
GE100LO 5.118 130 4.449 113 10.58 4.8 4 137,000 610 690,000 3050
GE110LO 5.512 140 4.882 124 12.79 5.8 4 147,000 655 730,000 3250
GE125LO 6.299 160 5.433 138 18.74 8.5 4 214,000 950 1,070,000 4750
GE160LO 7.874 200 6.969 177 36.38 16.5 4 310,000 1370 1,530,000 6800
GE200LO 9.843 250 8.701 221 70.56 32 4 475,000 2120 2,380,000 10600
GE250LO 13.780 350 12.480 317 218.30 99 4 800,000 3550 4,050,000 18000
GE320LO 17.717 450 15.945 405 529.20 240 4 1,370,000 6100 6,900,000 30500

384
Elges
Radial Spherical Plain Bearings
GE..HO-2RS SERIES
D Sliding contact surfaces: steel/steel
D Hardened inner and outer ring
D Extended inner ring for clevis mount
D Outer ring with single (axial) split

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C
NUMBER inch mm inch mm inch mm inch mm
GE17HO2RS 0.669 17 1.181 30 0.827 21 0.394 10
GE20HO2RS 0.787 20 1.378 35 0.945 24 0.472 12
GE25HO2RS 0.984 25 1.654 42 1.142 29 0.630 16
GE30HO2RS 1.181 30 1.850 47 1.181 30 0.709 18
GE35HO2RS 1.378 35 2.165 55 1.378 35 0.787 20
GE40HO2RS 1.575 40 2.441 62 1.496 38 0.866 22
GE45HO2RS 1.772 45 2.677 68 1.575 40 0.984 25
GE50HO2RS 1.969 50 2.953 75 1.693 43 1.102 28
GE60HO2RS 2.362 60 3.543 90 2.126 54 1.417 36
GE70HO2RS 2.756 70 4.134 105 2.559 65 1.575 40
GE80HO2RS 3.150 80 4.724 120 2.913 74 1.772 45

CONTINUED FROM ABOVE

PART dk dk d2 d2 ALPHA WGT. WGT C C C0 C0
NUMBER inch mm inch mm deg lbs kg lbf kN lbf kN
GE17HO2RS 0.984 25 0.827 21 3 0.088 0.04 4,750 21.2 23,800 106
GE20HO2RS 1.142 29 0.945 24 3 0.126 0.057 6,700 30 33,000 146
GE25HO2RS 1.398 35.5 1.142 29 3 0.221 0.1 10,800 48 54,000 240
GE30HO2RS 1.602 40.7 1.347 34.2 3 0.309 0.14 13,900 62 70,000 310
GE35HO2RS 1.850 47 1.575 40 3 0.529 0.24 18,000 80 90,000 400
GE40HO2RS 2.087 53 1.772 45 3 0.639 0.29 22,500 100 112,000 500
GE45HO2RS 2.362 60 2.028 51.5 3 0.948 0.43 28,500 127 144,000 640
GE50HO2RS 2.598 66 2.224 56.5 3 1.191 0.54 35,000 156 175,000 780
GE60HO2RS 3.150 80 2.665 67.7 3 2.426 1.1 55,000 245 275,000 1220
GE70HO2RS 3.622 92 3.071 78 3 3.528 1.6 71,000 315 350,000 1560
GE80HO2RS 4.134 105 3.543 90 3 5.292 2.4 90,000 400 450,000 2000

385
Elges
Radial Spherical Plain Bearings
GE..ZO SERIES
D Inch series
D Sliding contact surfaces: steel/steel
D Hardened inner and outer ring
D Outer ring with single (axial) split

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART SHAFT SHAFT OD OD WIDTH WIDTH WIDTH WIDTH BALL BALL ANGLE WGT WGT . DYN. DYN STAT. STAT.
NUMBER d d D D B B C C DIA. DIA. alpha CAP. CAP. CAP. CAP.
dK dK x1000 x1000
inch mm inch mm inch mm inch mm inch mm deg lbs kg lbf kN lbf kN
GE12ZO 0.500 12.700 0.875 22.225 0.437 11.100 0.375 9.525 0.719 18.263 14 0.044 0.020 3.1 13.7 15.5 59
GE15ZO 0.625 15.875 1.063 26.988 0.547 13.894 0.469 11.913 0.899 22.835 14 0.079 0.036 5.0 22.0 25.0 110
GE19ZO 0.750 19.050 1.250 31.750 0.656 16.662 0.562 14.275 1.080 27.432 14 0.126 0.057 7.10 31.50 35 157
GE22ZO 0.875 22.225 1.438 36.513 0.765 19.431 0.656 16.662 1.258 31.953 14 0.193 0.088 9.60 42.50 48 213
GE25ZO 1.000 25.400 1.625 41.275 0.875 22.225 0.750 19.050 1.437 36.500 13 0.276 0.125 12.50 56 63 280
GE31ZO 1.250 31.750 2.000 50.800 1.093 27.762 0.937 23.800 1.795 45.593 13 0.516 0.234 19.50 87 98 435
GE34ZO 1.375 34.925 2.188 55.563 1.187 30.150 1.031 26.187 1.937 49.200 13 0.770 0.349 23.20 103 116 520
GE38ZO 1.500 38.100 2.438 61.913 1.312 33.325 1.125 28.575 2.155 54.737 13 0.934 0.424 28.00 125 141 630
GE44ZO 1.750 44.450 2.813 71.438 1.531 38.887 1.313 33.338 2.515 63.881 13 1.430 0.649 38.50 170 192 850
GE50ZO 2.000 50.800 3.188 80.963 1.750 44.450 1.500 38.100 2.875 73.025 12 2.070 0.939 50 223 250 1110
GE57ZO 2.250 57.150 3.563 90.488 1.969 50.013 1.688 42.863 3.235 82.169 12 2.920 1.324 63 280 315 1410
GE63ZO 2.500 63.500 3.938 100.013 2.187 55.550 1.875 47.625 3.590 91.186 12 4.090 1.855 78 345 390 1740
GE69ZO 2.750 69.850 4.375 111.125 2.406 61.112 2.063 52.388 3.950 100.330 12 5.380 2.440 95 420 475 2100
GE76ZO 3.000 76.200 4.750 120.650 2.625 66.675 2.250 57.150 4.312 109.525 12 6.870 3.116 113 500 560 2500
GE82ZO 3.250 82.550 5.125 130.175 2.844 72.238 2.438 61.913 4.675 118.745 12 8.630 3.914 132 590 660 2950
GE88ZO 3.500 88.900 5.500 139.700 3.062 77.775 2.625 66.675 5.040 128.016 11 10.650 4.830 154 680 770 3400
GE95ZO 3.750 95.250 5.875 149.225 3.281 83.337 2.813 71.438 5.390 136.906 11 12.950 5.873 176 780 880 3900
GE101ZO 4.000 101.600 6.250 158.750 3.500 88.900 3.000 76.200 5.750 146.050 11 15.590 7.070 200 890 1000 4450
GE114ZO 4.500 114.300 7.000 177.800 3.937 100.000 3.375 85.725 6.475 164.465 7 21.920 9.941 255 1130 1270 5600
GE127ZO 5.000 127.000 7.750 196.850 4.375 111.125 3.750 95.250 7.190 182.626 7 29.710 13.474 315 1390 1560 7000
GE152ZO 6.000 152.400 8.750 222.250 4.750 120.650 4.125 104.775 8.156 207.162 7 38.770 17.583 390 1740 1950 8700

386
Elges
Radial Spherical Plain Bearings
GE..ZO-2RS SERIES
D Inch series, sealed
D Sliding contact surfaces: steel/steel
D Hardened inner and outer ring
D Outer ring with single (axial) split

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD WIDTH WIDTH WIDTH WIDTH
d d D D B B C C

inch mm inch mm inch mm inch mm

GE19ZO 2RS 0.750 19.050 1.250 31.750 0.656 16.662 0.562 14.275
GE22ZO 2RS 0.875 22.225 1.438 36.513 0.765 19.431 0.656 16.662
GE25ZO 2RS 1.000 25.400 1.625 41.275 0.875 22.225 0.750 19.050
GE31ZO 2RS 1.250 31.750 2.000 50.800 1.093 27.762 0.937 23.800
GE34ZO 2RS 1.375 34.925 2.188 55.563 1.187 30.150 1.031 26.187
GE38ZO 2RS 1.500 38.100 2.438 61.913 1.312 33.325 1.125 28.575
GE44ZO 2RS 1.750 44.450 2.813 71.438 1.531 38.887 1.313 33.338
GE50ZO 2RS 2.000 50.800 3.188 80.963 1.750 44.450 1.500 38.100
GE57ZO 2RS 2.250 57.150 3.563 90.488 1.969 50.013 1.688 42.863
GE63ZO 2RS 2.500 63.500 3.938 100.013 2.187 55.550 1.875 47.625
GE69ZO 2RS 2.750 69.850 4.375 111.125 2.406 61.112 2.063 52.388
GE76ZO 2RS 3.000 76.200 4.750 120.650 2.625 66.675 2.250 57.150
GE82ZO 2RS 3.250 82.550 5.125 130.175 2.844 72.238 2.438 61.913
GE88ZO 2RS 3.500 88.900 5.500 139.700 3.062 77.775 2.625 66.675
GE95ZO 2RS 3.750 95.250 5.875 149.225 3.281 83.337 2.813 71.438
GE101ZO 2RS 4.000 101.600 6.250 158.750 3.500 88.900 3.000 76.200
GE114ZO 2RS 4.500 114.300 7.000 177.800 3.937 100.000 3.375 85.725
GE127ZO 2RS 5.000 127.000 7.750 196.850 4.375 111.125 3.750 95.250
GE152ZO 2RS 6.000 152.400 8.750 222.250 4.750 120.650 4.125 104.775

CONTINUED FROM ABOVE

PART NUMBER BALL BALL ANGLE WGT WGT DYN. CAP. DYN. CAP. STAT. CAP. STAT. CAP.
DIA. DIA. alpha
dK dK x1000 x1000
inch mm deg lbs kg lbf kN lbf kN
GE19ZO 2RS 1.080 27.4 7 0.126 0.057 7.10 31.50 35 157
GE22ZO 2RS 1.258 32.0 7 0.193 0.088 9.60 42.50 48 213
GE25ZO 2RS 1.437 36.5 7 0.276 0.125 12.50 56 63 280
GE31ZO 2RS 1.795 45.6 7 0.516 0.234 19.50 87 98 435
GE34ZO 2RS 1.937 49.2 7 0.770 0.349 23.20 103 116 520
GE38ZO 2RS 2.155 54.7 7 0.934 0.424 28.00 125 141 630
GE44ZO 2RS 2.515 63.9 7 1.430 0.649 38.50 170 192 850
GE50ZO 2RS 2.875 73.0 7 2.070 0.939 50 223 250 1110
GE57ZO 2RS 3.235 82.2 7 2.920 1.324 63 280 315 1410
GE63ZO 2RS 3.590 91.2 7 4.090 1.855 78 345 390 1740
GE69ZO 2RS 3.950 100.3 7 5.380 2.440 95 420 475 2100
GE76ZO 2RS 4.312 109.5 7 6.870 3.116 113 500 560 2500
GE82ZO 2RS 4.675 118.7 7 8.630 3.914 132 590 660 2950
GE88ZO 2RS 5.040 128.0 7 10.650 4.830 154 680 770 3400
GE95ZO 2RS 5.390 136.9 7 12.950 5.873 176 780 880 3900
GE101ZO 2RS 5.750 146.1 7 15.590 7.070 200 890 1000 4450
GE114ZO 2RS 6.475 164.5 7 21.920 9.941 255 1130 1270 5600
GE127ZO 2RS 7.190 182.6 7 29.710 13.474 315 1390 1560 7000
GE152ZO 2RS 8.156 207.2 7 38.770 17.583 390 1740 1950 8700

387
Elges Angular Contact
Spherical Plain Bearings
GE..SX SERIES
D Sliding contact surfaces: steel/steel

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D T T WGT. WGT C C C0 C0 dk dk
NUMBER inch mm inch mm inch mm lbs kg lbf kN lbf kN inch mm
GE25SX 0.984 25 1.850 47 0.591 15 0.287 0.13 10,700 47.5 53,000 236 1.673 42.5
GE28SX 1.102 28 2.047 52 0.630 16 0.375 0.17 13,500 60 67,000 300 1.850 47
GE30SX 1.181 30 2.165 55 0.669 17 0.463 0.21 14,200 63 71,000 315 1.969 50
GE35SX 1.378 35 2.441 62 0.709 18 0.595 0.27 17,200 76.5 88,000 390 2.205 56
GE40SX 1.575 40 2.677 68 0.748 19 0.706 0.32 20,200 90 101,000 450 2.362 60
GE45SX 1.772 45 2.953 75 0.787 20 0.904 0.41 23,800 106 119,000 530 2.598 66
GE50SX 1.969 50 3.150 80 0.787 20 0.992 0.45 26,500 118 132,000 585 2.913 74
GE55SX 2.165 55 3.543 90 0.906 23 1.477 0.67 33,000 146 165,000 735 3.150 80
GE60SX 2.362 60 3.740 95 0.906 23 1.588 0.72 36,000 160 180,000 800 3.386 86
GE65SX 2.559 65 3.937 100 0.906 23 1.676 0.76 39,000 173 194,000 865 3.622 92
GE70SX 2.756 70 4.331 110 0.984 25 2.205 1 47,000 208 234,000 1040 4.016 102
GE80SX 3.150 80 4.921 125 1.102 28 3.308 1.5 56,000 250 280,000 1250 4.528 115
GE90SX 3.543 90 5.512 140 1.260 32 4.631 2.1 72,000 320 360,000 1600 5.118 130
GE100SX 3.937 100 5.906 150 1.260 32 5.072 2.3 78,000 345 395,000 1760 5.512 140
GE110SX 4.331 110 6.693 170 1.496 38 7.938 3.6 107,000 475 530,000 2360 6.299 160
GE120SX 4.724 120 7.087 180 1.496 38 8.600 3.9 115,000 510 570,000 2550 6.693 170
GE130SX 5.118 130 7.874 200 1.772 45 13.010 5.9 144,000 640 720,000 3200 7.480 190
GE140SX 5.512 140 8.268 210 1.772 45 13.892 6.3 153,000 680 780,000 3450 7.874 200
GE150SX 5.906 150 8.858 225 1.890 48 16.979 7.7 175,000 780 880,000 3900 8.386 213
GE160SX 6.299 160 9.449 240 2.008 51 20.727 9.4 202,000 900 1,010,000 4500 8.858 225
GE170SX 6.693 170 10.236 260 2.244 57 26.460 12 247,000 1100 1,240,000 5500 9.843 250
GE180SX 7.087 180 11.024 280 2.520 64 37.485 17 295,000 1320 1,510,000 6700 10.236 260
GE190SX 7.480 190 11.417 290 2.520 64 39.690 18 310,000 1370 1,560,000 6950 10.827 275
GE200SX 7.874 200 12.205 310 2.756 70 49.613 22.5 350,000 1560 1,750,000 7800 11.417 290

388
Elges Angular Contact
Spherical Plain Bearings
GE..SX SERIES
D Sliding contact surfaces: steel/steel

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
D1 D1 B B C C s s A A PART
inch mm inch mm inch mm inch mm inch mm NUMBER

1.236 31.4 0.551 14 0.551 14 0.039 1 0.295 7.5 GE25SX

1.406 35.7 0.591 15 0.591 15 0.039 1 0.315 8 GE28SX
1.421 36.1 0.630 16 0.630 16 0.079 2 0.335 8.5 GE30SX
1.669 42.4 0.669 17 0.669 17 0.079 2 0.354 9 GE35SX
1.843 46.8 0.709 18 0.709 18 0.059 1.5 0.374 9.5 GE40SX
2.083 52.9 0.748 19 0.748 19 0.059 1.5 0.394 10 GE45SX
2.327 59.1 0.748 19 0.748 19 0.158 4 0.394 10 GE50SX
2.441 62 0.866 22 0.866 22 0.158 4 0.453 11.5 GE55SX
2.681 68.1 0.866 22 0.866 22 0.197 5 0.453 11.5 GE60SX
2.976 75.6 0.866 22 0.866 22 0.197 5 0.453 11.5 GE65SX
3.236 82.2 0.945 24 0.945 24 0.276 7 0.492 12.5 GE70SX
3.563 90.5 1.063 27 1.063 27 0.394 10 0.571 14.5 GE80SX
4.067 103.3 1.181 30 1.181 30 0.433 11 0.630 16 GE90SX
4.500 114.3 1.181 30 1.181 30 0.472 12 0.630 16 GE100SX
4.953 125.8 1.417 36 1.417 36 0.591 15 0.748 19 GE110SX
5.331 135.4 1.417 36 1.417 36 0.669 17 0.748 19 GE120SX
5.827 148 1.654 42 1.654 42 0.787 20 0.886 22.5 GE130SX
6.323 160.6 1.654 42 1.654 42 0.787 20 0.886 22.5 GE140SX
6.728 170.9 1.772 45 1.772 45 0.827 21 0.945 24 GE150SX
7.142 181.4 1.890 48 1.890 48 0.827 21 1.004 25.5 GE160SX
7.650 194.3 2.126 54 2.126 54 1.063 27 1.122 28.5 GE170SX
8.091 205.5 2.402 61 2.402 61 0.827 21 1.260 32 GE180SX
8.339 211.8 2.402 61 2.402 61 1.142 29 1.260 32 GE190SX
9.024 229.2 2.598 66 2.598 66 1.024 26 1.378 35 GE200SX

389
Elges Axial
Spherical Plain Bearings
GE..AX SERIES
D Sliding contact surfaces: steel/steel

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D H H WGT. WGT C C C0 C0 dk dk d2 d2
NUMBER
inch mm inch mm inch mm lbs kg lbf kN lbf kN inch mm inch mm
GE10AX 0.394 10 1.181 30 0.374 9.5 0.088 0.04 5,400 24 27,000 120 1.260 32 1.083 27.5
GE12AX 0.472 12 1.378 35 0.512 13 0.154 0.07 7,300 32.5 36,500 163 1.457 37 1.260 32
GE15AX 0.591 15 1.654 42 0.591 15 0.265 0.12 11,700 52 58,000 260 1.772 45 1.532 38.9
GE17AX 0.669 17 1.850 47 0.630 16 0.353 0.16 13,200 58.5 67,000 300 1.969 50 1.709 43.4
GE20AX 0.787 20 2.165 55 0.787 20 0.551 0.25 16,900 75 84,000 375 2.362 60 1.969 50
GE25AX 0.984 25 2.441 62 0.886 22.5 0.838 0.38 29,000 129 144,000 640 2.598 66 2.264 57.5
GE30AX 1.181 30 2.953 75 1.024 26 1.433 0.65 38,000 170 191,000 850 3.150 80 2.717 69
GE35AX 1.378 35 3.543 90 1.102 28 2.205 1 58,000 260 290,000 1290 3.858 98 3.307 84
GE40AX 1.575 40 4.134 105 1.260 32 3.528 1.6 84,000 375 420,000 1860 4.488 114 3.858 98
GE45AX 1.772 45 4.724 120 1.437 36.5 5.292 2.4 110,000 490 550,000 2450 5.118 130 4.409 112
GE50AX 1.969 50 5.118 130 1.673 42.5 7.277 3.3 147,000 655 730,000 3250 5.512 140 4.823 122.5
GE60AX 2.362 60 5.906 150 1.772 45 9.92 4.5 165,000 735 820,000 3650 6.299 160 5.512 140
GE70AX 2.756 70 6.299 160 1.969 50 12.13 5.5 180,000 800 910,000 4050 6.693 170 5.886 149.5
GE80AX 3.150 80 7.087 180 1.969 50 15.44 7 234,000 1040 1,170,000 5200 7.638 194 6.614 168
GE100AX 3.937 100 8.268 210 2.323 59 23.15 10.5 270,000 1200 1,350,000 6000 8.661 220 7.697 195.5
GE120AX 4.724 120 9.055 230 2.520 64 28.67 13 280,000 1250 1,390,000 6200 9.646 245 8.425 214
GE140AX 5.512 140 10.236 260 2.835 72 39.69 18 365,000 1630 1,830,000 8150 10.709 272 9.606 244
GE160AX 6.299 160 11.417 290 3.032 77 50.72 23 425,000 1900 2,140,000 9500 12.205 310 10.709 272
GE180AX 7.087 180 12.598 320 3.386 86 68.36 31 475,000 2120 2,380,000 10600 13.189 335 11.811 300
GE200AX 7.874 200 13.386 340 3.425 87 74.97 34 530,000 2360 2,650,000 11800 14.095 358 12.638 321

CONTINUED FROM ABOVE

PART d3 d3 D1 D1 B B C C s s A A ALPHA da da Da Da
NUMBER max. max. min. min.
inch mm inch mm inch mm inch mm inch mm inch mm deg inch mm inch mm
GE10AX 0.827 21 0.650 16.5 0.311 7.9 0.236 6 0.276 7 0.118 3 10 0.827 21 0.728 18.5
GE12AX 0.945 24 0.768 19.5 0.366 9.3 0.354 9 0.315 8 0.158 4 9 0.945 24 0.847 21.5
GE15AX 1.142 29 0.945 24 0.421 10.7 0.433 11 0.394 10 0.197 5 7 1.142 29 1.024 26
GE17AX 1.339 34 1.102 28 0.453 11.5 0.453 11.5 0.433 11 0.197 5 6 1.339 34 1.201 30.5
GE20AX 1.575 40 1.319 33.5 0.563 14.3 0.512 13 0.492 12.5 0.236 6 6 1.575 40 1.496 38
GE25AX 1.772 45 1.358 34.5 0.630 16 0.669 17 0.551 14 0.236 6 7 1.772 45 1.535 39
GE30AX 2.205 56 1.732 44 0.709 18 0.768 19.5 0.689 17.5 0.315 8 6 2.205 56 1.929 49
GE35AX 2.598 66 2.047 52 0.866 22 0.787 20 0.866 22 0.315 8 6 2.598 66 2.244 57
GE40AX 3.071 78 2.323 59 1.063 27 0.866 22 0.965 24.5 0.354 9 6 3.071 78 2.520 64
GE45AX 3.504 89 2.677 68 1.221 31 0.984 25 1.083 27.5 0.433 11 6 3.504 89 2.913 74
GE50AX 3.858 98 2.717 69 1.319 33.5 1.260 32 1.181 30 0.394 10 5 3.858 98 2.953 75
GE60AX 4.252 108 3.386 86 1.457 37 1.299 33 1.378 35 0.492 12.5 7 4.252 108 3.622 92
GE70AX 4.764 121 3.740 95 1.575 40 1.417 36 1.378 35 0.532 13.5 6 4.764 121 4.016 102
GE80AX 5.118 130 4.252 108 1.654 42 1.417 36 1.673 42.5 0.571 14.5 6 5.118 130 4.528 115
GE100AX 6.102 155 5.236 133 1.969 50 1.654 42 1.772 45 0.591 15 7 6.102 155 5.551 141
GE120AX 6.693 170 6.063 154 2.047 52 1.772 45 2.067 52.5 0.650 16.5 8 6.693 170 6.378 162
GE140AX 7.795 198 6.929 176 2.402 61 1.969 50 2.067 52.5 0.906 23 6 7.795 198 7.362 187
GE160AX 8.386 213 7.835 199 2.559 65 2.047 52 2.559 65 0.906 23 7 8.386 213 8.307 211
GE180AX 9.449 240 8.819 224 2.756 70 2.362 60 2.658 67.5 1.024 26 8 9.449 240 9.291 236
GE200AX 10.433 265 9.685 246 2.913 74 2.362 60 2.756 70 1.063 27 8 10.433 265 10.197 259

390
Elges
Thrust Spherical Plain Bearings
GE..ZSX SERIES
D Inch series
D Sliding contact surfaces: steel/steel
D Hardened housing and shaft locating washers

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART NUMBER SHAFT SHAFT OD OD TOTAL TOTAL WIDTH WIDTH WIDTH WIDTH
d d D D WIDTH WIDTH B B C C
T T
inch mm inch mm inch mm inch mm inch mm
GE12ZSX 0.500 12.700 0.875 22.225 0.300 7.620 0.270 6.858 0.190 4.826
GE15ZSX 0.625 15.875 1.063 26.988 0.370 9.398 0.340 8.636 0.250 6.350
GE19ZSX 0.750 19.050 1.250 31.750 0.440 11.176 0.410 10.414 0.310 7.874
GE22ZSX 0.875 22.225 1.438 36.513 0.520 13.208 0.480 12.192 0.380 9.652
GE25ZSX 1.000 25.400 1.625 41.275 0.600 15.240 0.550 13.970 0.440 11.176
GE31ZSX 1.250 31.750 2.000 50.800 0.740 18.796 0.700 17.780 0.550 13.970
GE34ZSX 1.375 34.925 2.188 55.563 0.840 21.336 0.770 19.558 0.600 15.240
GE38ZSX 1.500 38.100 2.438 61.913 0.910 23.114 0.840 21.336 0.660 16.764
GE44ZSX 1.750 44.450 2.813 71.438 1.070 27.178 0.980 24.892 0.790 20.066
GE50ZSX 2.000 50.800 3.188 80.963 1.230 31.242 1.130 28.702 0.920 23.368
GE57ZSX 2.250 57.150 3.563 90.488 1.390 35.306 1.270 32.258 1.050 26.670
GE63ZSX 2.500 63.500 3.938 100.013 1.540 39.116 1.420 36.068 1.180 29.972
GE69ZSX 2.750 69.850 4.375 111.125 1.700 43.180 1.560 39.624 1.275 32.385
GE76ZSX 3.000 76.200 4.750 120.650 1.860 47.244 1.710 43.434 1.406 35.712
GE82ZSX 3.250 82.550 5.125 130.175 2.030 51.562 1.860 47.244 1.545 39.243
GE88ZSX 3.500 88.900 5.500 139.700 2.180 55.372 2.000 50.800 1.675 42.545
GE95ZSX 3.750 95.250 5.875 149.225 2.340 59.436 2.150 54.610 1.805 45.847
GE101ZSX 4.000 101.600 6.250 158.750 2.500 63.500 2.300 58.420 1.935 49.149
GE114ZSX 4.500 114.300 7.000 177.800 2.800 71.120 2.590 65.786 2.195 55.753
GE127ZSX 5.000 127.000 7.750 196.850 3.130 79.502 2.880 73.152 2.455 62.357
GE152ZSX 6.000 152.400 8.750 222.250 3.375 85.725 3.100 78.740 2.615 66.421

PART NUMBER BALL BALL WEIGHT WEIGHT DYN. CAP. DYN. CAP. STAT. CAP. STAT. CAP.
DIA. DIA.
dK dK x1000 x1000
inch mm lbs kg lbf kN lbf kN
GE12ZSX 0.719 18.263 0.029 0.013 1.68 7.50 8.40 37.50
GE15ZSX 0.899 22.835 0.056 0.025 2.75 12.30 13.90 62
GE19ZSX 1.080 27.432 0.083 0.038 4.15 18.40 20.60 92
GE22ZSX 1.258 31.953 0.110 0.050 5.90 26.00 29.50 131
GE25ZSX 1.437 36.500 0.188 0.085 7.80 34.50 39 173
GE31ZSX 1.795 45.593 0.351 0.159 12.20 54 61 270
GE34ZSX 1.937 49.200 0.470 0.213 14.30 64 72 320
GE38ZSX 2.155 54.737 0.662 0.300 17.50 78 88 390
GE44ZSX 2.515 63.881 1.010 0.458 24.50 109 122 540
GE50ZSX 2.875 73.025 1.480 0.671 32.50 145 163 730
GE57ZSX 3.235 82.169 2.090 0.948 42 186 209 930
GE63ZSX 3.590 91.186 2.490 1.129 52 232 260 1160
GE69ZSX 3.950 100.330 3.860 1.751 62 275 310 1380
GE76ZSX 4.312 109.525 6.670 3.025 75 330 375 1660
GE82ZSX 4.675 118.745 6.360 2.884 89 395 445 1980
GE88ZSX 5.040 128.016 7.870 3.569 104 465 520 2310
GE95ZSX 5.390 136.906 9.590 4.349 120 530 600 2650
GE101ZSX 5.750 146.050 11.56 5.243 137 610 690 3050
GE114ZSX 6.475 164.465 17.12 7.764 175 780 880 3900
GE127ZSX 7.190 182.626 24.40 11.07 218 970 1090 4850
GE152ZSX 8.156 207.162 38.34 17.39 265 1170 1310 5800

391
Elges
Radial Spherical Plain Bearings
GE..UK SERIES
GE..UK-2RS SERIES
D DIN 648, dimension series E – ISO 6124/1
D Sliding contact surfaces: hard chromium/PTFE
D Sliding contact surfaces available with:
corrosion resistant steel/PTFE – suffix W1

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C WGT. WGT
NUMBER
inch mm inch mm inch mm inch mm lbs kg
GE6UK 0.236 6 0.551 14 0.236 6 0.158 4 0.009 0.004
GE8UK 0.315 8 0.630 16 0.315 8 0.197 5 0.015 0.007
GE10UK 0.394 10 0.748 19 0.354 9 0.236 6 0.024 0.011
GE12UK 0.472 12 0.866 22 0.394 10 0.276 7 0.035 0.016
GE15UK 0.591 15 1.024 26 0.472 12 0.354 9 0.055 0.025
GE17UK 0.669 17 1.181 30 0.551 14 0.394 10 0.084 0.038
GE20UK 0.787 20 1.378 35 0.630 16 0.472 12 0.135 0.061
GE25UK 0.984 25 1.654 42 0.787 20 0.630 16 0.243 0.11
GE30UK 1.181 30 1.850 47 0.866 22 0.709 18 0.309 0.14
GE17UK2RS 0.669 17 1.181 30 0.551 14 0.394 10 0.084 0.038
GE20UK2RS 0.787 20 1.378 35 0.630 16 0.472 12 0.135 0.061
GE25UK2RS 0.984 25 1.654 42 0.787 20 0.630 16 0.243 0.11
GE30UK2RS 1.181 30 1.850 47 0.866 22 0.709 18 0.309 0.14
GE35UK2RS 1.378 35 2.165 55 0.984 25 0.787 20 0.485 0.22
GE40UK2RS 1.575 40 2.441 62 1.102 28 0.866 22 0.662 0.3
GE45UK2RS 1.772 45 2.677 68 1.260 32 0.984 25 0.882 0.4
GE50UK2RS 1.969 50 2.953 75 1.378 35 1.102 28 1.191 0.54
GE60UK2RS 2.362 60 3.543 90 1.732 44 1.417 36 2.205 1
GE70UK2RS 2.756 70 4.134 105 1.929 49 1.575 40 3.308 1.5
GE80UK2RS 3.150 80 4.724 120 2.165 55 1.772 45 4.851 2.2
GE90UK2RS 3.543 90 5.118 130 2.362 60 1.969 50 5.954 2.7
GE100UK2RS 3.937 100 5.906 150 2.756 70 2.165 55 9.482 4.3
GE110UK2RS 4.331 110 6.299 160 2.756 70 2.165 55 10.36 4.7
GE120UK2RS 4.724 120 7.087 180 3.347 85 2.756 70 17.64 8
GE140UK2RS 5.512 140 8.268 210 3.543 90 2.756 70 24.26 11
GE160UK2RS 6.299 160 9.055 230 4.134 105 3.150 80 29.77 13.5
GE180UK2RS 7.087 180 10.236 260 4.134 105 3.150 80 40.79 18.5
GE200UK2RS 7.874 200 11.417 290 5.118 130 3.937 100 61.74 28
GE220UK2RS 8.661 220 12.598 320 5.315 135 3.937 100 78.28 35.5
GE240UK2RS 9.449 240 13.386 340 5.512 140 3.937 100 88.20 40
GE260UK2RS 10.236 260 14.567 370 5.906 150 4.331 110 110.25 50
GE280UK2RS 11.024 280 15.748 400 6.102 155 4.724 120 141.12 64
GE300UK2RS 11.811 300 16.929 430 6.496 165 4.724 120 165.38 75

392
Elges
Radial Spherical Plain Bearings
GE..UK SERIES
GE..UK-2RS SERIES
D DIN 648, dimension series E – ISO 6124/1
D Sliding contact surfaces: hard chromium/PTFE
D Sliding contact surfaces available with:
corrosion resistant steel/PTFE – suffix W1

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
C C C0 C0 dk dk ALPHA da da Da Da PART
max. max. min. min. NUMBER
lbf kN lbf kN inch mm deg inch mm inch mm
810 3.6 2,020 9 0.394 10 13 0.315 8 0.378 9.6 GE6UK
1,320 5.85 3,300 14.6 0.512 13 15 0.402 10.2 0.492 12.5 GE8UK
1,950 8.65 4,850 21.6 0.630 16 12 0.520 13.2 0.610 15.5 GE10UK
2,550 11.4 6,400 28.5 0.709 18 11 0.587 14.9 0.689 17.5 GE12UK
3,950 17.6 9,900 44 0.866 22 8 0.724 18.4 0.827 21 GE15UK
5,000 22.4 12,600 56 0.984 25 10 0.815 20.7 0.945 24 GE17UK
7,100 31.5 17,500 78 1.142 29 9 0.949 24.1 1.083 27.5 GE20UK
11,500 51 28,500 127 1.398 35.5 7 1.154 29.3 1.299 33 GE25UK
14,700 65.5 37,500 166 1.602 40.7 6 1.347 34.2 1.496 38 GE30UK
6,700 30 13,500 60 0.984 25 10 0.815 20.7 0.945 24 GE17UK2RS
9,300 41.5 18,700 83 1.142 29 9 0.949 24.1 1.083 27.5 GE20UK2RS
15,300 68 31,000 137 1.398 35.5 7 1.154 29.3 1.299 33 GE25UK2RS
19,800 88 39,500 176 1.602 40.7 6 1.347 34.2 1.496 38 GE30UK2RS
25,000 112 50,000 224 1.850 47 6 1.563 39.7 1.752 44.5 GE35UK2RS
31,500 140 63,000 280 2.087 53 7 1.772 45 2.008 51 GE40UK2RS
40,500 180 81,000 360 2.362 60 7 1.996 50.7 2.244 57 GE45UK2RS
49,500 220 99,000 440 2.598 66 6 2.201 55.9 2.480 63 GE50UK2RS
78,000 345 156,000 695 3.150 80 6 2.630 66.8 2.953 75 GE60UK2RS
99,000 440 198,000 880 3.622 92 6 3.063 77.8 3.425 87 GE70UK2RS
128,000 570 255,000 1140 4.134 105 6 3.520 89.4 3.898 99 GE80UK2RS
156,000 695 310,000 1370 4.528 115 5 3.862 98.1 4.252 108 GE90UK2RS
194,000 865 390,000 1730 5.118 130 7 4.311 109.5 4.843 123 GE100UK2RS
209,000 930 420,000 1860 5.512 140 6 4.772 121.2 5.276 134 GE110UK2RS
300,000 1340 610,000 2700 6.299 160 6 5.335 135.5 5.906 150 GE120UK2RS
335,000 1500 670,000 3000 7.087 180 7 6.134 155.8 6.811 173 GE140UK2RS
435,000 1930 850,000 3800 7.874 200 8 6.701 170.2 7.520 191 GE160UK2RS
485,000 2160 970,000 4300 8.858 225 6 7.831 198.9 8.622 219 GE180UK2RS
670,000 3000 1,350,000 6000 9.843 250 7 8.406 213.5 9.409 239 GE200UK2RS
750,000 3350 1,470,000 6550 10.827 275 8 9.429 239.5 10.512 267 GE220UK2RS
810,000 3600 1,620,000 7200 11.811 300 8 10.445 265.3 11.614 295 GE240UK2RS
970,000 4300 1,940,000 8650 12.795 325 7 11.350 288.3 12.559 319 GE260UK2RS
1,120,000 5000 2,250,000 10000 13.780 350 6 12.354 313.8 13.465 342 GE280UK2RS
1,210,000 5400 2,430,000 10800 14.764 375 7 13.256 336.7 14.567 370 GE300UK2RS

393
Elges
Radial Spherical Plain Bearings
GE..DW SERIES
D DIN 648, dimension series C – ISO 6124/3
D Sliding contact surfaces: hard chromium/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C WGT. WGT
NUMBER
inch mm inch mm inch mm inch mm lbs kg
GE320DW 12.598 320 17.323 440 6.299 160 5.315 135 167.58 76
GE340DW 13.386 340 18.110 460 6.299 160 5.315 135 176.40 80
GE360DW 14.173 360 18.898 480 6.299 160 5.315 135 189.63 86
GE380DW 14.961 380 20.472 520 7.480 190 6.299 160 275.63 125
GE400DW 15.748 400 21.260 540 7.480 190 6.299 160 286.65 130
GE420DW 16.535 420 22.047 560 7.480 190 6.299 160 315.32 143
GE440DW 17.323 440 23.622 600 8.583 218 7.284 185 414.54 188
GE460DW 18.110 460 24.409 620 8.583 218 7.284 185 438.80 199
GE480DW 18.898 480 25.591 650 9.055 230 7.677 195 520.38 236
GE500DW 19.685 500 26.378 670 9.055 230 7.677 195 535.82 243
GE530DW 20.866 530 27.953 710 9.567 243 8.071 205 635.04 288
GE560DW 22.047 560 29.528 750 10.158 258 8.465 215 745.29 338
GE600DW 23.622 600 31.496 800 10.709 272 9.055 230 897.44 407

394
Elges
Radial Spherical Plain Bearings
GE..DW SERIES
D DIN 648, dimension series C – ISO 6124/3
D Sliding contact surfaces: hard chromium/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
C C C0 C0 dk dk ALPHA da da Da Da PART
x1000 x1000 max. max. min. min. NUMBER
lbf kN lbf kN inch mm deg inch mm inch mm
1730 7695 3450 15390 14.961 380 4 13.567 344.6 14.213 361 GE320DW
1820 8100 3650 16200 15.748 400 3.8 14.433 366.6 15.039 382 GE340DW
1910 8505 3800 17010 16.535 420 3.6 15.287 388.3 15.866 403 GE360DW
2430 10800 4850 21600 17.717 450 4.1 16.059 407.9 16.772 426 GE380DW
2550 11280 5100 22560 18.504 470 3.9 16.921 429.8 17.598 447 GE400DW
2650 11760 5300 23520 19.291 490 3.7 17.780 451.6 18.465 469 GE420DW
3250 14430 6500 28860 20.472 520 3.9 18.583 472 19.331 491 GE440DW
3350 14985 6700 29970 21.260 540 3.7 19.449 494 20.197 513 GE460DW
3700 16525 7400 33050 22.244 565 3.8 20.315 516 21.102 536 GE480DW
3850 17110 7700 34220 23.032 585 3.6 21.173 537.8 21.929 557 GE500DW
4300 19065 6300 28130 24.409 620 3.7 22.453 570.3 23.268 591 GE530DW
4750 21125 9500 42250 25.787 655 4 23.701 602 24.567 624 GE560DW
5400 24150 10900 48300 27.559 700 3.6 25.390 644.9 26.260 667 GE600DW

395
Elges
Radial Spherical Plain Bearings
GE..FW, GE..FW-2RS SERIES
D Metric
D DIN 648, dimension series G – ISO 6124/1
D Sliding contact surfaces: hard chromium/PTFE
D Matching dimensions with series GE..FO

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C WGT. WGT
NUMBER
inch mm inch mm inch mm inch mm lbs kg
GE6FW 0.236 6 0.630 16 0.354 9 0.197 5 0.018 0.008
GE8FW 0.315 8 0.748 19 0.433 11 0.236 6 0.031 0.014
GE10FW 0.394 10 0.866 22 0.472 12 0.276 7 0.044 0.02
GE12FW 0.472 12 1.024 26 0.591 15 0.354 9 0.075 0.034
GE15FW 0.591 15 1.181 30 0.630 16 0.394 10 0.101 0.046
GE17FW 0.669 17 1.378 35 0.787 20 0.472 12 0.172 0.078
GE20FW 0.787 20 1.654 42 0.984 25 0.630 16 0.331 0.15
GE25FW 0.984 25 1.850 47 1.102 28 0.709 18 0.419 0.19
GE30FW2RS 1.181 30 2.165 55 1.260 32 0.787 20 0.639 0.29
GE35FW2RS 1.378 35 2.441 62 1.378 35 0.866 22 0.86 0.39
GE40FW2RS 1.575 40 2.677 68 1.575 40 0.984 25 1.147 0.52
GE45FW2RS 1.772 45 2.953 75 1.693 43 1.102 28 1.499 0.68
GE50FW2RS 1.969 50 3.543 90 2.205 56 1.417 36 3.087 1.4
GE60FW2RS 2.362 60 4.134 105 2.480 63 1.575 40 4.41 2
GE70FW2RS 2.756 70 4.724 120 2.756 70 1.772 45 6.395 2.9
GE80FW2RS 3.150 80 5.118 130 2.953 75 1.969 50 7.718 3.5
GE90FW2RS 3.543 90 5.906 150 3.347 85 2.165 55 11.91 5.4
GE100FW2RS 3.937 100 6.299 160 3.347 85 2.165 55 13.01 5.9
GE110FW2RS 4.331 110 7.087 180 3.937 100 2.756 70 21.39 9.7
GE120FW2RS 4.724 120 8.268 210 4.528 115 2.756 70 33.08 15
GE140FW2RS 5.512 140 9.055 230 5.118 130 3.150 80 40.79 18.5
GE160FW2RS 6.299 160 10.236 260 5.315 135 3.150 80 55.13 25
GE180FW2RS 7.087 180 11.417 290 6.102 155 3.937 100 78.28 35.5
GE200FW2RS 7.874 200 12.598 320 6.496 165 3.937 100 99.23 45
GE220FW2RS 8.661 220 13.386 340 6.890 175 3.937 100 112.46 51
GE240FW2RS 9.449 240 14.567 370 7.480 190 4.331 110 141.12 64
GE260FW2RS 10.236 260 15.748 400 8.071 205 4.724 120 178.61 81
GE280FW2RS 11.024 280 16.929 430 8.268 210 4.724 120 207.27 94

396
Elges
Radial Spherical Plain Bearings
GE..FW, GE..FW-2RS SERIES
D Metric
D DIN 648, dimension series G – ISO 6124/1
D Sliding contact surfaces: hard chromium/PTFE
D Matching dimensions with series GE..UK

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
C C C0 C0 dk dk ALPHA da da Da Da PART
max. max. min. min. NUMBER
lbf kN lbf kN inch mm deg inch mm inch mm
1,320 5.85 3,300 14.6 0.512 13 21 0.366 9.3 0.492 12.5 GE6FW
1,950 8.65 4,850 21.6 0.630 16 21 0.457 11.6 0.610 15.5 GE8FW
2,550 11.4 6,400 28.5 0.709 18 18 0.528 13.4 0.689 17.5 GE10FW
3,950 17.6 9,900 44 0.866 22 18 0.630 16 0.827 21 GE12FW
5,000 22.4 12,600 56 0.984 25 16 0.756 19.2 0.945 24 GE15FW
7,100 31.5 17,500 78 1.142 29 19 0.827 21 1.083 27.5 GE17FW
11,500 51 28,500 127 1.398 35.5 17 0.992 25.2 1.299 33 GE20FW
14,700 65.5 37,500 166 1.602 40.7 17 1.161 29.5 1.496 38 GE25FW
25,000 112 50,000 224 1.850 47 17 1.354 34.4 1.752 44.5 GE30FW2RS
31,500 140 63,000 280 2.087 53 16 1.563 39.7 2.008 51 GE35FW2RS
40,500 180 81,000 360 2.362 60 17 1.760 44.7 2.244 57 GE40FW2RS
49,500 220 99,000 440 2.598 66 15 1.969 50 2.480 63 GE45FW2RS
78,000 345 156,000 695 3.150 80 17 2.248 57.1 2.953 75 GE50FW2RS
99,000 440 198,000 880 3.622 92 17 2.638 67 3.425 87 GE60FW2RS
128,000 570 255,000 1140 4.134 105 16 3.079 78.2 3.898 99 GE70FW2RS
156,000 695 310,000 1370 4.528 115 14 3.429 87.1 4.252 108 GE80FW2RS
194,000 865 390,000 1730 5.118 130 15 3.870 98.3 4.843 123 GE90FW2RS
209,000 930 420,000 1860 5.512 140 14 4.378 111.2 5.276 134 GE100FW2RS
300,000 1340 610,000 2700 6.299 160 12 4.913 124.8 5.906 150 GE110FW2RS
335,000 1500 670,000 3000 7.087 180 16 5.449 138.4 6.811 173 GE120FW2RS
435,000 1930 850,000 3800 7.874 200 16 5.980 151.9 7.520 191 GE140FW2RS
485,000 2160 970,000 4300 8.858 225 16 7.087 180 8.622 219 GE160FW2RS
670,000 3000 1,350,000 6000 9.843 250 14 7.721 196.1 9.409 239 GE180FW2RS
750,000 3350 1,470,000 6550 10.827 275 15 8.661 220 10.512 267 GE200FW2RS
810,000 3600 1,620,000 7200 11.811 300 16 9.591 243.6 11.614 295 GE220FW2RS
970,000 4300 1,940,000 8650 12.795 325 15 10.378 263.6 12.559 319 GE240FW2RS
1,120,000 5000 2,250,000 10000 13.780 350 15 11.165 283.6 13.465 342 GE260FW2RS
1,210,000 5400 2,430,000 10800 14.764 375 15 12.228 310.6 14.567 370 GE280FW2RS

397
Elges
Radial Spherical Plain Bearings
GE..PW SERIES
D Metric
D DIN 648, dimension series K
D Maintenance free
D Sliding contact surfaces: steel/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C WGT. WGT
NUMBER
inch mm inch mm inch mm inch mm lbs kg
GE5PW 0.197 5 0.512 13 0.315 8 0.236 6 0.013 0.006
GE6PW 0.236 6 0.630 16 0.354 9 0.266 6.75 0.022 0.01
GE8PW 0.315 8 0.748 19 0.472 12 0.354 9 0.04 0.018
GE10PW 0.394 10 0.866 22 0.551 14 0.413 10.5 0.06 0.027
GE12PW 0.472 12 1.024 26 0.630 16 0.472 12 0.095 0.043
GE14PW 0.551 14 1.102 28 0.748 19 0.532 13.5 0.121 0.055
GE16PW 0.630 16 1.260 32 0.827 21 0.591 15 0.176 0.08
GE18PW 0.709 18 1.378 35 0.906 23 0.650 16.5 0.221 0.1
GE20PW 0.787 20 1.575 40 0.984 25 0.709 18 0.331 0.15
GE22PW 0.866 22 1.654 42 1.102 28 0.787 20 0.397 0.18
GE25PW 0.984 25 1.850 47 1.221 31 0.866 22 0.529 0.24
GE30PW 1.181 30 2.165 55 1.457 37 0.984 25 0.838 0.38

398
Elges
Radial Spherical Plain Bearings
GE..PW SERIES
D Metric
D DIN 648, dimension series K
D Maintenance free
D Sliding contact surfaces: steel/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
C C C0 C0 dk dk ALPHA da da Da Da PART
max. max. min. min. NUMBER
lbf kN lbf kN inch mm deg inch mm inch mm
1,350 6 3,350 15 0.438 11.112 13 0.303 7.7 0.386 9.8 GE5PW
1,720 7.65 4,350 19.3 0.500 12.7 13 0.350 8.9 0.453 11.5 GE6PW
2,900 12.9 7,200 32 0.625 15.875 14 0.406 10.3 0.551 14 GE8PW
4,050 18 10,100 45 0.750 19.05 13 0.508 12.9 0.669 17 GE10PW
5,400 24 13,500 60 0.875 22.225 13 0.606 15.4 0.768 19.5 GE12PW
7,000 31 17,200 76.5 1.000 25.4 16 0.661 16.8 0.886 22.5 GE14PW
8,800 39 21,700 96.5 1.125 28.575 15 0.760 19.3 1.004 25.5 GE16PW
10,700 47.5 26,500 118 1.250 31.75 15 0.858 21.8 1.122 28.5 GE18PW
12,800 57 31,500 140 1.375 34.925 14 0.957 24.3 1.240 31.5 GE20PW
15,300 68 38,000 170 1.500 38.1 15 1.016 25.8 1.339 34 GE22PW
19,100 85 47,500 212 1.687 42.85 15 1.161 29.5 1.516 38.5 GE25PW
25,500 114 64,000 285 2.000 50.8 17 1.370 34.8 1.811 46 GE30PW

399
Elges Angular Contact
Spherical Plain Bearings
GE..SW SERIES
D Sliding contact surfaces: hard chromium/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D T T WGT. WGT C C C0 C0 dk dk D1 D1
NUMBER
inch mm inch mm inch mm lbs kg lbf kN lbf kN inch mm inch mm
GE25SW 0.984 25 1.850 47 0.591 15 0.309 0.14 16,000 71 31,500 140 1.673 42.5 1.236 31.4
GE28SW 1.102 28 2.047 52 0.630 16 0.397 0.18 20,200 90 40,500 180 1.850 47 1.406 35.7
GE30SW 1.181 30 2.165 55 0.669 17 0.485 0.22 21,400 95 42,500 190 1.969 50 1.421 36.1
GE32SW 1.260 32 2.284 58 0.669 17 0.529 0.24 22,900 102 46,000 204 2.087 53 1.547 39.3
GE35SW 1.378 35 2.441 62 0.709 18 0.617 0.28 26,000 116 52,000 232 2.205 56 1.669 42.4
GE40SW 1.575 40 2.677 68 0.748 19 0.75 0.34 30,000 134 61,000 270 2.362 60 1.843 46.8
GE45SW 1.772 45 2.953 75 0.787 20 0.948 0.43 36,000 160 72,000 320 2.598 66 2.083 52.9
GE50SW 1.969 50 3.150 80 0.787 20 1.036 0.47 39,500 176 80,000 355 2.913 74 2.327 59.1
GE55SW 2.165 55 3.543 90 0.906 23 1.544 0.7 49,500 220 99,000 440 3.150 80 2.441 62
GE60SW 2.362 60 3.740 95 0.906 23 1.654 0.75 54,000 240 108,000 480 3.386 86 2.681 68.1
GE65SW 2.559 65 3.937 100 0.906 23 1.764 0.8 58,000 260 117,000 520 3.622 92 2.976 75.6
GE70SW 2.756 70 4.331 110 0.984 25 2.205 1 71,000 315 142,000 630 4.016 102 3.236 82.2
GE80SW 3.150 80 4.921 125 1.142 29 3.528 1.6 84,000 375 169,000 750 4.528 115 3.563 90.5
GE90SW 3.543 90 5.512 140 1.260 32 4.851 2.2 108,000 480 217,000 965 5.118 130 4.067 103.3
GE100SW 3.937 100 5.906 150 1.260 32 5.292 2.4 117,000 520 234,000 1040 5.512 140 4.500 114.3
GE110SW 4.331 110 6.693 170 1.496 38 8.16 3.7 160,000 710 320,000 1430 6.299 160 4.953 125.8
GE120SW 4.724 120 7.087 180 1.496 38 8.82 4 172,000 765 345,000 1530 6.693 170 5.331 135.4
GE130SW 5.118 130 7.874 200 1.772 45 13.23 6 217,000 965 435,000 1930 7.480 190 5.827 148
GE140SW 5.512 140 8.268 210 1.772 45 14.11 6.4 229,000 1020 460,000 2040 7.874 200 6.323 160.6
GE150SW 5.906 150 8.858 225 1.890 48 17.42 7.9 265,000 1180 530,000 2360 8.386 213 6.728 170.9
GE160SW 6.299 160 9.449 240 2.008 51 21.17 9.6 300,000 1340 610,000 2700 8.858 225 7.142 181.4
GE170SW 6.693 170 10.236 260 2.244 57 28.67 13 375,000 1660 750,000 3350 9.843 250 7.650 194.3
GE180SW 7.087 180 11.024 280 2.520 64 38.59 17.5 450,000 2000 900,000 4000 10.236 260 8.091 205.5
GE190SW 7.480 190 11.417 290 2.520 64 39.69 18 470,000 2080 930,000 4150 10.827 275 8.339 211.8
GE200SW 7.874 200 12.205 310 2.756 70 50.72 23 530,000 2360 1,070,000 4750 11.417 290 9.024 229.2

400
Elges Angular Contact
Spherical Plain Bearings
GE..SW SERIES
D Sliding contact surfaces: hard chromium/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
B B C C s s da da db db Da Da Db Db PART
max. max. max. max. min. min. min. min. NUMBER
inch mm inch mm inch mm inch mm inch mm inch mm inch mm
0.551 14 0.551 14 0.039 1 1.185 30.1 1.555 39.5 1.339 34 1.693 43 GE25SW
0.591 15 0.591 15 0.039 1 1.354 34.4 1.654 42 1.575 40 1.870 47.5 GE28SW
0.630 16 0.630 16 0.079 2 1.362 34.6 1.772 45 1.595 40.5 1.988 50.5 GE30SW
0.630 16 0.630 16 0.098 2.5 1.492 37.9 1.870 47.5 1.732 44 2.126 54 GE32SW
0.669 17 0.669 17 0.079 2 1.618 41.1 1.969 50 1.850 47 2.244 57 GE35SW
0.709 18 0.709 18 0.059 1.5 1.791 45.5 2.126 54 2.047 52 2.402 61 GE40SW
0.748 19 0.748 19 0.059 1.5 2.035 51.7 2.362 60 2.284 58 2.638 67 GE45SW
0.748 19 0.748 19 0.158 4 2.280 57.9 2.638 67 2.559 65 2.953 75 GE50SW
0.866 22 0.866 22 0.158 4 2.390 60.7 2.795 71 2.756 70 3.189 81 GE55SW
0.866 22 0.866 22 0.197 5 2.634 66.9 3.032 77 2.992 76 3.425 87 GE60SW
0.866 22 0.866 22 0.197 5 2.929 74.4 3.268 83 3.307 84 3.661 93 GE65SW
0.945 24 0.945 24 0.276 7 3.185 80.9 3.622 92 3.543 90 4.095 104 GE70SW
1.063 27 1.063 27 0.394 10 3.465 88 4.095 104 3.898 99 4.606 117 GE80SW
1.181 30 1.181 30 0.433 11 3.969 100.8 4.646 118 4.409 112 5.197 132 GE90SW
1.181 30 1.181 30 0.472 12 4.409 112 5.039 128 4.843 123 5.630 143 GE100SW
1.417 36 1.417 36 0.591 15 4.850 123.2 5.748 146 5.315 135 6.378 162 GE110SW
1.417 36 1.417 36 0.669 17 5.232 132.9 6.102 155 5.709 145 6.772 172 GE120SW
1.654 42 1.654 42 0.787 20 5.665 143.9 6.850 174 6.221 158 7.559 192 GE130SW
1.654 42 1.654 42 0.787 20 6.177 156.9 7.244 184 6.732 171 7.953 202 GE140SW
1.772 45 1.772 45 0.827 21 6.579 167.1 7.638 194 7.244 184 8.504 216 GE150SW
1.890 48 1.890 48 0.827 21 6.996 177.7 8.110 206 7.677 195 8.976 228 GE160SW
2.126 54 2.126 54 1.063 27 7.496 190.4 8.976 228 8.189 208 9.961 253 GE170SW
2.402 61 2.402 61 0.827 21 7.941 201.7 9.449 240 8.661 220 10.354 263 GE180SW
2.402 61 2.402 61 1.142 29 8.185 207.9 9.921 252 8.898 226 10.945 278 GE190SW
2.598 66 2.598 66 1.024 26 8.823 224.1 10.551 268 9.606 244 11.535 293 GE200SW

401
Elges Axial
Spherical Plain Bearings
GE..AW SERIES
D Sliding contact surfaces: hard chromium/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D H H WGT. WGT C C C0 C0 dk dk d2 d2
NUMBER x1000 x1000
inch mm inch mm inch mm lbs kg lbf kN lbf kN inch mm inch mm
GE10AW 0.394 10 1.181 30 0.374 9.5 0.088 0.04 8.1 36 16.2 72 1.260 32 1.083 27.5
GE12AW 0.472 12 1.378 35 0.512 13 0.154 0.07 11 49 22 98 1.457 37 1.260 32
GE15AW 0.591 15 1.654 42 0.591 15 0.265 0.12 17.5 78 35 156 1.772 45 1.532 38.9
GE17AW 0.669 17 1.850 47 0.630 16 0.353 0.16 19.8 88 39.5 176 1.969 50 1.709 43.4
GE20AW 0.787 20 2.165 55 0.787 20 0.551 0.25 25 112 50 224 2.362 60 1.969 50
GE25AW 0.984 25 2.441 62 0.886 22.5 0.838 0.38 43.5 193 88 390 2.598 66 2.264 57.5
GE30AW 1.181 30 2.953 75 1.024 26 1.433 0.65 57 255 115 510 3.150 80 2.717 69
GE35AW 1.378 35 3.543 90 1.102 28 2.205 1 88 390 175 780 3.858 98 3.307 84
GE40AW 1.575 40 4.134 105 1.260 32 3.528 1.6 126 560 250 1120 4.488 114 3.858 98
GE45AW 1.772 45 4.724 120 1.437 36.5 5.292 2.4 165 735 330 1460 5.118 130 4.409 112
GE50AW 1.969 50 5.118 130 1.673 42.5 7.277 3.3 220 980 440 1960 5.512 140 4.823 122.5
GE60AW 2.362 60 5.906 150 1.772 45 9.923 4.5 247 1100 495 2200 6.299 160 5.512 140
GE70AW 2.756 70 6.299 160 1.969 50 12.13 5.5 270 1200 540 2400 6.693 170 5.886 149.5
GE80AW 3.150 80 7.087 180 1.969 50 15.44 7 350 1560 700 3100 7.638 194 6.614 168
GE100AW 3.937 100 8.268 210 2.323 59 23.15 10.5 405 1800 810 3600 8.661 220 7.697 195.5
GE120AW 4.724 120 9.055 230 2.520 64 28.67 13 420 1860 840 3750 9.646 245 8.425 214
GE140AW 5.512 140 10.236 260 2.835 72 39.69 18 550 2450 1100 4900 10.709 272 9.606 244
GE160AW 6.299 160 11.417 290 3.032 77 50.72 23 640 2850 1280 5700 12.205 310 10.709 272
GE180AW 7.087 180 12.598 320 3.386 86 68.36 31 720 3200 1440 6400 13.189 335 11.811 300
GE200AW 7.874 200 13.386 340 3.425 87 74.97 34 800 3550 1600 7100 14.095 358 12.638 321
GE220AW 8.661 220 14.567 370 3.819 97 98.12 44.5 990 4400 1980 8800 15.276 388 13.780 350
GE240AW 9.449 240 15.748 400 4.055 103 121.28 55 1170 5200 2340 10400 16.535 420 15.039 382
GE260AW 10.236 260 16.929 430 4.528 115 152.15 69 1210 5400 2430 10800 17.677 449 16.102 409
GE280AW 11.024 280 18.110 460 4.331 110 180.81 82 1910 8500 3800 17000 18.898 480 17.520 445
GE300AW 11.811 300 18.898 480 4.331 110 191.84 87 1940 8650 3900 17300 19.291 490 18.110 460
GE320AW 12.598 320 20.472 520 4.567 116 240.35 109 2380 10600 4750 21200 21.260 540 19.685 500
GE340AW 13.386 340 21.260 540 4.567 116 251.37 114 2650 11800 5300 23600 21.654 550 20.079 510
GE360AW 14.173 360 22.047 560 4.921 125 284.45 129 2850 12700 5700 25500 22.638 575 21.063 535

402
Elges Axial
Spherical Plain Bearings
GE..AW SERIES
D Sliding contact surfaces: hard chromium/PTFE

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
d3 d3 D1 D1 B B C C s s ALPHA da da Da Da PART
min. min. NUMBER
inch mm inch mm inch mm inch mm inch mm deg inch mm inch mm
0.827 21 0.650 16.5 0.311 7.9 0.236 6 0.276 7 10 0.827 21 0.728 18.5 GE10AW
0.945 24 0.768 19.5 0.366 9.3 0.354 9 0.315 8 9 0.945 24 0.847 21.5 GE12AW
1.142 29 0.945 24 0.421 10.7 0.433 11 0.394 10 7 1.142 29 1.024 26 GE15AW
1.339 34 1.102 28 0.453 11.5 0.453 11.5 0.433 11 6 1.339 34 1.201 30.5 GE17AW
1.575 40 1.319 33.5 0.563 14.3 0.512 13 0.492 12.5 6 1.575 40 1.496 38 GE20AW
1.772 45 1.358 34.5 0.630 16 0.669 17 0.551 14 7 1.772 45 1.535 39 GE25AW
2.205 56 1.732 44 0.709 18 0.768 19.5 0.689 17.5 6 2.205 56 1.929 49 GE30AW
2.598 66 2.047 52 0.866 22 0.787 20 0.866 22 6 2.598 66 2.244 57 GE35AW
3.071 78 2.323 59 1.063 27 0.866 22 0.965 24.5 6 3.071 78 2.520 64 GE40AW
3.504 89 2.677 68 1.221 31 0.984 25 1.083 27.5 6 3.504 89 2.913 74 GE45AW
3.858 98 2.717 69 1.319 33.5 1.260 32 1.181 30 5 3.858 98 2.953 75 GE50AW
4.252 108 3.386 86 1.457 37 1.299 33 1.378 35 7 4.252 108 3.622 92 GE60AW
4.764 121 3.740 95 1.575 40 1.417 36 1.378 35 6 4.764 121 4.016 102 GE70AW
5.118 130 4.252 108 1.654 42 1.417 36 1.673 42.5 6 5.118 130 4.528 115 GE80AW
6.102 155 5.236 133 1.969 50 1.654 42 1.772 45 7 6.102 155 5.551 141 GE100AW
6.693 170 6.063 154 2.047 52 1.772 45 2.067 52.5 8 6.693 170 6.378 162 GE120AW
7.795 198 6.929 176 2.402 61 1.969 50 2.067 52.5 6 7.795 198 7.362 187 GE140AW
8.386 213 7.835 199 2.559 65 2.047 52 2.559 65 7 8.386 213 8.307 211 GE160AW
9.449 240 8.819 224 2.756 70 2.362 60 2.658 67.5 8 9.449 240 9.291 236 GE180AW
10.433 265 9.685 246 2.913 74 2.362 60 2.756 70 8 10.433 265 10.197 259 GE200AW
11.378 289 10.433 265 3.228 82 2.638 67 2.953 75 7 11.378 289 10.984 279 GE220AW
12.362 314 11.575 294 3.425 87 2.874 73 3.051 77.5 6 12.362 314 12.165 309 GE240AW
13.228 336 12.480 317 3.740 95 3.150 80 3.248 82.5 7 13.228 336 13.071 332 GE260AW
14.409 366 13.268 337 3.937 100 3.347 85 3.150 80 4 14.409 366 13.976 355 GE280AW
15.276 388 14.016 356 3.937 100 3.543 90 3.150 80 3.5 15.276 388 14.764 375 GE300AW
15.945 405 14.961 380 4.134 105 3.583 91 3.740 95 4 15.945 405 15.827 402 GE320AW
17.008 432 14.961 380 4.134 105 3.583 91 3.740 95 4 17.008 432 15.827 402 GE340AW
17.795 452 15.748 400 4.528 115 3.740 95 3.740 95 4 17.795 452 16.614 422 GE360AW

403
Elges Rod Ends
GIR..DO, GIR..DO-2RS SERIES
D Metric
D DIN 648, dimension series E Form B – ISO 6126
D Sliding contact surfaces: steel/steel
D Left hand thread is available on shank, order by replacing “R” with “L”
D Internal thread

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2 d3
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIR6DO 0.236 6 0.551 14 0.236 6 760 3.4 1830 8.15 0.046 0.021 0.394 10 0.315 8 0.827 21 M6
GIR8DO 0.315 8 0.630 16 0.315 8 1240 5.5 2900 12.9 0.086 0.039 0.512 13 0.402 10.2 0.945 24 M8
GIR10DO 0.394 10 0.748 19 0.354 9 1830 8.15 3950 17.6 0.135 0.061 0.630 16 0.520 13.2 1.142 29 M10
GIR12DO 0.472 12 0.866 22 0.394 10 2430 10.8 5500 24.5 0.212 0.096 0.709 18 0.587 14.9 1.339 34 M12
GIR15DO 0.591 15 1.024 26 0.472 12 3800 17 8100 36 0.397 0.18 0.866 22 0.724 18.4 1.575 40 M14
GIR17DO 0.669 17 1.181 30 0.551 14 4750 21.2 10100 45 0.485 0.22 0.984 25 0.815 20.7 1.811 46 M16
GIR20DO 0.787 20 1.378 35 0.630 16 6700 30 13500 60 0.772 0.35 1.142 29 0.949 24.1 2.087 53 M20X1.5
GIR25DO2RS 0.984 25 1.654 42 0.787 20 10600 47 18700 83 1.411 0.64 1.398 35.5 1.154 29.3 2.520 64 M24X2
GIR30DO2RS 1.181 30 1.850 47 0.866 22 13900 62 24700 110 2.051 0.93 1.602 40.7 1.347 34.2 2.874 73 M30X2
GIR35DO2RS 1.378 35 2.165 55 0.984 25 18000 80 33000 146 2.867 1.3 1.850 47 1.563 39.7 3.228 82 M36X3
GIR40DO2RS 1.575 40 2.441 62 1.102 28 22500 100 40500 180 4.41 2 2.087 53 1.772 45 3.622 92 M39X3
GIR45DO2RS 1.772 45 2.677 68 1.260 32 28500 127 54000 240 5.513 2.5 2.362 60 1.996 50.7 4.016 102 M42X3
GIR50DO2RS 1.969 50 2.953 75 1.378 35 35000 156 65000 290 7.718 3.5 2.598 66 2.201 55.9 4.409 112 M45X3
GIR60DO2RS 2.362 60 3.543 90 1.732 44 55000 245 101000 450 12.13 5.5 3.150 80 2.630 66.8 5.315 135 M52X3
GIR70DO2RS 2.756 70 4.134 105 1.929 49 71000 315 137000 610 18.96 8.6 3.622 92 3.063 77.8 6.299 160 M56X4
GIR80DO2RS 3.150 80 4.724 120 2.165 55 90000 400 169000 750 26.46 12 4.134 105 3.520 89.4 7.087 180 M64X4

CONTINUED FROM ABOVE

PART d4 d4 h1 h1 C1 C1 ALPHA l3 l3 l4 l4 l5 l5 l7 l7 d5 d5 W W
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm inch mm
GIR6DO 0.394 10 1.181 30 0.173 4.4 13 0.433 11 1.595 40.5 0.197 5 0.472 12 0.512 13 0.433 11
GIR8DO 0.492 12.5 1.417 36 0.236 6 15 0.591 15 1.890 48 0.197 5 0.551 14 0.630 16 0.551 14
GIR10DO 0.591 15 1.693 43 0.276 7 12 0.787 20 2.264 57.5 0.256 6.5 0.591 15 0.748 19 0.669 17
GIR12DO 0.689 17.5 1.969 50 0.315 8 11 0.906 23 2.638 67 0.256 6.5 0.709 18 0.866 22 0.748 19
GIR15DO 0.827 21 2.402 61 0.394 10 8 1.181 30 3.189 81 0.315 8 0.787 20 1.024 26 0.866 22
GIR17DO 0.945 24 2.638 67 0.433 11 10 1.339 34 3.543 90 0.394 10 0.906 23 1.181 30 1.063 27
GIR20DO 1.083 27.5 3.032 77 0.512 13 9 1.575 40 4.075 103.5 0.394 10 1.063 27 1.378 35 1.260 32
GIR25DO2RS 1.319 33.5 3.701 94 0.669 17 7 1.890 48 4.961 126 0.472 12 1.260 32 1.654 42 1.417 36
GIR30DO2RS 1.575 40 4.331 110 0.748 19 6 2.205 56 5.768 146.5 0.591 15 1.457 37 1.969 50 1.614 41
GIR35DO2RS 1.850 47 4.921 125 0.827 21 6 2.362 60 6.535 166 0.591 15 1.654 42 2.284 58 1.969 50
GIR40DO2RS 2.047 52 5.591 142 0.906 23 7 2.559 65 7.402 188 0.709 18 1.890 48 2.559 65 2.165 55
GIR45DO2RS 2.284 58 5.709 145 1.063 27 7 2.559 65 7.717 196 0.787 20 2.047 52 2.756 70 2.362 60
GIR50DO2RS 2.441 62 6.299 160 1.181 30 6 2.677 68 8.504 216 0.787 20 2.362 60 2.953 75 2.559 65
GIR60DO2RS 2.756 70 6.890 175 1.496 38 6 2.756 70 9.547 242.5 0.787 20 2.953 75 3.465 88 2.953 75
GIR70DO2RS 3.150 80 7.874 200 1.654 42 6 3.150 80 11.024 280 0.787 20 3.425 87 3.858 98 3.347 85
GIR80DO2RS 3.740 95 9.055 230 1.850 47 6 3.347 85 12.598 320 0.984 25 3.937 100 4.331 110 3.937 100

404
Elges Rod Ends
GAR..DO, GAR..DO-2RS SERIES
D Metric
D DIN 648, dimension series E Form A – ISO 6126
D Sliding contact surfaces: steel/steel
D Left hand thread is available on shank, order by replacing “R” with “L”
D External thread

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm
GAR6DO 0.236 6 0.551 14 0.236 6 760 3.4 1830 8.15 0.037 0.017 0.394 10 0.315 8
GAR8DO 0.315 8 0.630 16 0.315 8 1240 5.5 2900 12.9 0.064 0.029 0.512 13 0.402 10.2
GAR10DO 0.394 10 0.748 19 0.354 9 1830 8.15 3950 17.6 0.112 0.051 0.630 16 0.520 13.2
GAR12DO 0.472 12 0.866 22 0.394 10 2430 10.8 5500 24.5 0.19 0.086 0.709 18 0.587 14.9
GAR15DO 0.591 15 1.024 26 0.472 12 3800 17 8100 36 0.309 0.14 0.866 22 0.724 18.4
GAR17DO 0.669 17 1.181 30 0.551 14 4750 21.2 10100 45 0.419 0.19 0.984 25 0.815 20.7
GAR20DO2RS 0.787 20 1.378 35 0.630 16 6700 30 13500 60 0.684 0.31 1.142 29 0.949 24.1
GAR25DO2RS 0.984 25 1.654 42 0.787 20 10800 48 18700 83 1.235 0.56 1.398 35.5 1.154 29.3
GAR30DO2RS 1.181 30 1.850 47 0.866 22 13900 62 24700 110 1.962 0.89 1.602 40.7 1.347 34.2
GAR35DO2RS 1.378 35 2.165 55 0.984 25 18000 80 33000 146 3.087 1.4 1.850 47 1.563 39.7
GAR40DO2RS 1.575 40 2.441 62 1.102 28 22500 100 40500 180 3.969 1.8 2.087 53 1.772 45
GAR45DO2RS 1.772 45 2.677 68 1.260 32 28500 127 54000 240 5.733 2.6 2.362 60 1.996 50.7
GAR50DO2RS 1.969 50 2.953 75 1.378 35 35000 156 65000 290 7.497 3.4 2.598 66 2.201 55.9
GAR60DO2RS 2.362 60 3.543 90 1.732 44 55000 245 101000 450 13.01 5.9 3.150 80 2.630 66.8
GAR70DO2RS 2.756 70 4.134 105 1.929 49 71000 315 137000 610 18.08 8.2 3.622 92 3.063 77.8
GAR80DO2RS 3.150 80 4.724 120 2.165 55 90000 400 169000 750 26.46 12 4.134 105 3.520 89.4

CONTINUED FROM ABOVE

PART d2 d2 d3 h h C1 C1 ALPHA l1 l1 l2 l2 l7 l7
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm
GAR6DO 0.827 21 M6 1.417 36 0.173 4.4 13 0.709 18 1.8307 46.5 0.472 12
GAR8DO 0.945 24 M8 1.654 42 0.236 6 15 0.866 22 2.126 54 0.551 14
GAR10DO 1.142 29 M10 1.890 48 0.276 7 12 1.024 26 2.4606 62.5 0.591 15
GAR12DO 1.339 34 M12 2.126 54 0.315 8 11 1.102 28 2.7953 71 0.709 18
GAR15DO 1.575 40 M14 2.480 63 0.394 10 8 1.339 34 3.2677 83 0.787 20
GAR17DO 1.811 46 M16 2.717 69 0.433 11 10 1.417 36 3.622 92 0.906 23
GAR20DO2RS 2.087 53 M20X1.5 3.071 78 0.512 13 9 1.693 43 4.1142 104.5 1.063 27
GAR25DO2RS 2.520 64 M24X2 3.701 94 0.669 17 7 2.087 53 16.7717 426 1.260 32
GAR30DO2RS 2.874 73 M30X2 4.331 110 0.748 19 6 2.559 65 5.7677 146.5 1.457 37
GAR35DO2RS 3.228 82 M36X3 5.512 140 0.827 21 6 3.228 82 7.126 181 1.654 42
GAR40DO2RS 3.622 92 M39X3 5.906 150 0.906 23 7 3.386 86 7.7165 196 1.890 48
GAR45DO2RS 4.016 102 M42X3 6.417 163 1.063 27 7 3.701 94 8.4252 214 2.047 52
GAR50DO2RS 4.409 112 M45X3 7.284 185 1.181 30 6 4.213 107 9.4882 241 2.362 60
GAR60DO2RS 5.315 135 M52X3 8.268 210 1.496 38 6 4.528 115 10.9252 277.5 2.953 75
GAR70DO2RS 6.299 160 M56X4 9.252 235 1.654 42 6 4.921 125 12.4016 315 3.307 84
GAR80DO2RS 7.087 180 M64X4 10.630 270 1.850 47 6 5.512 140 14.1732 360 3.937 100

405
Elges Hydraulic Rod Ends
GIHNK..LO SERIES
D DIN 24338 – ISO 6982 series
D Sliding contact surfaces: steel/steel
D With thread clamping screws

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2 d3
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIHNK 12 LO 0.472 12 0.866 22 0.472 12 2,430 10.8 5,500 24.5 0.221 0.1 0.709 18 0.610 15.5 1.260 32 M12X1.25
GIHNK 16 LO 0.630 16 1.102 28 0.630 16 3,950 17.6 8,200 36.5 0.441 0.2 0.906 23 0.787 20 1.575 40 M14X1.5
GIHNK 20 LO 0.787 20 1.378 35 0.787 20 6,700 30 10,800 48 0.882 0.4 1.142 29 0.984 25 1.850 47 M16X1.5
GIHNK 25 LO 0.984 25 1.654 42 0.984 25 10,800 48 17,500 78 1.455 0.66 1.398 35.5 1.201 30.5 2.284 58 M20X1.5
GIHNK 32 LO 1.260 32 2.047 52 1.260 32 15,100 67 25,500 114 2.646 1.2 1.732 44 1.496 38 2.756 70 M27X2
GIHNK 40 LO 1.575 40 2.441 62 1.575 40 22,500 100 46,000 204 4.631 2.1 2.087 53 1.811 46 3.504 89 M33X2
GIHNK 50 LO 1.969 50 2.953 75 1.969 50 35,000 156 70,000 310 9.702 4.4 2.598 66 2.244 57 4.252 108 M42X2
GIHNK 63 LO 2.480 63 3.740 95 2.480 63 57,000 255 97,000 430 16.76 7.6 3.268 83 2.815 71.5 5.197 132 M48X2
GIHNK 70 LO 2.756 70 4.134 105 2.756 70 71,000 315 121,000 540 20.95 9.5 3.622 92 3.110 79 6.102 155 M56X2
GIHNK 80 LO 3.150 80 4.724 120 3.150 80 90,000 400 156,000 695 31.97 14.5 4.134 105 3.583 91 6.614 168 M64X3
GIHNK 90 LO 3.543 90 5.118 130 3.543 90 110,000 490 169,000 750 37.49 17 4.528 115 3.898 99 7.284 185 M72X3
GIHNK 100 LO 3.937 100 5.906 150 3.937 100 137,000 610 238,000 1060 61.74 28 5.118 130 4.449 113 8.268 210 M80X3
GIHNK 110 LO 4.331 110 6.299 160 4.331 110 147,000 655 270,000 1200 70.56 32 5.512 140 4.882 124 9.252 235 M90X3
GIHNK 125 LO 4.921 125 7.087 180 4.921 125 214,000 950 320,000 1430 94.82 43 6.299 160 5.433 138 10.315 262 M100X3
GIHNK 160 LO 6.299 160 9.055 230 6.299 160 310,000 1370 495,000 2200 176.40 80 7.874 200 6.969 177 12.835 326 M125X4
GIHNK 200 LO 7.874 200 11.417 290 7.874 200 475,000 2120 820,000 3650 363.83 165 9.843 250 8.701 221 16.457 418 M160X4

CONTINUED FROM ABOVE

PART d4 d4 h1 h1 C1 C1 ALPHA l3 l3 l4 l4 l7 l7 d5 d5 C2 C2 CLAMP TORQUE
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm BOLT Nm
GIHNK 12 LO 0.650 16.5 1.496 38 0.417 10.6 4 0.669 17 2.126 54 0.551 14 1.260 32 0.417 10.6 M5X12 8
GIHNK 16 LO 0.827 21 1.732 44 0.512 13 4 0.709 18 2.520 64 0.709 18 1.575 40 0.512 13 M6X16 13
GIHNK 20 LO 0.984 25 2.047 52 0.669 17 4 0.906 23 2.961 75.2 0.866 22 1.850 47 0.669 17 M8X20 32
GIHNK 25 LO 1.181 30 2.559 65 0.827 21 4 1.142 29 3.701 94 1.063 27 2.126 54 0.669 17 M8X20 32
GIHNK 32 LO 1.496 38 3.150 80 1.063 27 4 1.457 37 4.528 115 1.260 32 2.598 66 0.866 22 M10X25 64
GIHNK 40 LO 1.850 47 3.819 97 1.260 32 4 1.811 46 5.571 141.5 1.614 41 3.150 80 1.024 26 M10X25 64
GIHNK 50 LO 2.284 58 4.724 120 1.575 40 4 2.244 57 6.850 174 1.969 50 3.780 96 1.260 32 M12X30 110
GIHNK 63 LO 2.756 70 5.512 140 2.047 52 4 2.520 64 8.307 211 2.441 62 4.488 114 1.496 38 M12X35 80
GIHNK 70 LO 3.150 80 6.299 160 2.244 57 4 2.992 76 9.646 245 2.756 70 5.315 135 1.654 42 M16X40 195
GIHNK 80 LO 3.543 90 7.087 180 2.598 66 4 3.386 86 10.630 270 3.071 78 5.827 148 1.890 48 M16X45 195
GIHNK 90 LO 3.937 100 7.677 195 2.835 72 4 3.583 91 11.654 296 3.347 85 6.299 160 2.047 52 M16X50 195
GIHNK 100 LO 4.331 110 8.268 210 3.307 84 4 3.780 96 12.677 322 3.858 98 7.008 178 2.441 62 M20X60 385
GIHNK 110 LO 4.921 125 9.252 235 3.465 88 4 4.173 106 14.331 364 4.134 105 7.480 190 2.441 62 M20X60 385
GIHNK 125 LO 5.315 135 10.236 260 4.016 102 4 4.449 113 15.945 405 4.724 120 7.874 200 2.835 72 M20X70 385
GIHNK 160 LO 6.496 165 12.205 310 5.118 130 4 4.961 126 19.213 488 5.906 150 9.843 250 3.228 82 M24X80 660
GIHNK 200 LO 8.465 215 15.354 390 6.378 162 4 6.339 161 24.409 620 7.677 195 12.598 320 4.016 102 M30X100 1350

406
Elges Hydraulic Rod Ends
GIHOK..DO SERIES
D DIN 24 555 series
D Spherical plain bearing to DIN 648
D Sliding contact surfaces: steel/steel
D With thread clamping screws

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2 d3
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIHO K 12 DO 0.472 12 0.866 22 0.394 10 2430 10.8 3800 17 0.331 0.15 0.709 18 0.591 15 1.260 32 M10X1.25
GIHO K 16 DO 0.630 16 1.181 30 0.551 14 4750 21.1 6400 28.5 0.551 0.25 0.984 25 0.787 20 1.654 42 M12X1.25
GIHO K 20 DO 0.787 20 1.378 35 0.630 16 6700 30 9600 42.5 0.948 0.43 1.142 29 0.945 24 1.969 50 M14X1.5
GIHO K 25 DO 0.984 25 1.654 42 0.787 20 10800 48 21800 97 1.61 0.73 1.398 35.5 1.142 29 1.654 42 M16X1.5
GIHO K 30 DO 1.181 30 1.850 47 0.866 22 13900 62 24300 108 2.867 1.3 1.602 40.7 1.339 34 2.992 76 M20X1.5
GIHO K 40 DO 1.575 40 2.441 62 1.102 28 22500 100 35000 156 5.072 2.3 2.087 53 1.772 45 3.780 96 M27X2
GIHO K 50 DO 1.969 50 2.953 75 1.378 35 35000 156 55000 245 9.702 4.4 2.598 66 2.165 55 4.567 116 M33X2

CONTINUED FROM ABOVE

PART d4 d4 h1 h1 C1 C1 ALPHA l3 l3 l4 l4 l7 l7 d5 d5 C2 C2 CLAMP TORQUE
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm BOLT Nm
GIHO K 12 DO 0.669 17 1.654 42 0.315 8 3 0.591 15 2.284 58 0.709 18 1.575 40 0.512 13 M6 9.5
GIHO K 16 DO 0.827 21 1.890 48 0.433 11 3 0.669 17 2.717 69 0.866 22 1.772 45 0.512 13 M6 9.5
GIHO K 20 DO 0.984 25 2.284 58 0.512 13 3 0.748 19 3.268 83 1.102 28 2.165 55 0.669 17 M8 23
GIHO K 25 DO 1.181 30 2.677 68 0.669 17 3 0.906 23 3.898 99 1.339 34 2.441 62 M8 23
GIHO K 30 DO 1.417 36 3.347 85 0.748 19 3 1.142 29 4.843 123 1.496 38 3.150 80 M10 46
GIHO K 40 DO 1.772 45 4.134 105 0.906 23 3 1.457 37 6.024 153 1.890 48 3.543 90 M10 46
GIHO K 50 DO 2.165 55 5.118 130 1.181 30 3 1.811 46 7.402 188 2.441 62 4.134 105 M12 80

407
Elges Hydraulic Rod Ends
GIHR..DO SERIES
D Sliding contact surfaces: steel/steel
D Rod ends with clamping threaded socket are prefix GIRH-K and the
bolts and tightening torques are shown.

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2
NUMBER
inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIHR 20 DO 0.787 20 1.378 35 0.630 16 6700 30 16200 72 0.948 0.43 1.142 29 0.949 24.1 2.205 56
GIHR 25 DO 0.984 25 1.654 42 0.787 20 10800 48 16200 72 1.058 0.48 1.398 35.5 1.154 29.3 2.205 56
GIHR 30 DO 1.181 30 1.850 47 0.866 22 13900 62 23800 106 1.632 0.74 1.602 40.7 1.347 34.2 2.520 64
GIHR 35 DO 1.378 35 2.165 55 0.984 25 18000 80 34500 153 2.646 1.2 1.850 47 1.563 39.7 3.071 78
GIHR 40 DO 1.575 40 2.441 62 1.102 28 22500 100 56000 250 4.41 2 2.087 53 1.772 45 3.701 94
GIHR 50 DO 1.969 50 2.953 75 1.378 35 35000 156 82000 365 8.379 3.8 2.598 66 2.201 55.9 4.567 116
GIHR 60 DO 2.362 60 3.543 90 1.732 44 55000 245 90000 400 11.91 5.4 3.150 80 2.630 66.8 5.118 130
GIHR 70 DO 2.756 70 4.134 105 1.929 49 71000 315 121000 540 18.74 8.5 3.622 92 3.063 77.8 6.063 154
GIHR 80 DO 3.150 80 4.724 120 2.165 55 90000 400 151000 670 26.46 12 4.134 105 3.520 89.4 6.929 176
GIHR 90 DO 3.543 90 5.118 130 2.362 60 110000 490 220000 980 47.41 21.5 4.528 115 3.862 98.1 8.110 206
GIHR 100 DO 3.937 100 5.906 150 2.756 70 137000 610 250000 1120 60.64 27.5 5.118 130 4.311 109.5 9.055 230
GIHR 110 DO 4.331 110 6.299 160 2.756 70 147000 655 380000 1700 89.30 40.5 5.512 140 4.772 121.2 10.433 265
GIHR 120 DO 4.724 120 7.087 180 3.347 85 214000 950 650000 2900 167.58 76 6.299 160 5.335 135.5 13.386 340

CONTINUED FROM ABOVE

PART d3 d4 d4 h1 h1 ALPHA l3 l3 l4 l4 l7 l7 d5 d5 C1 C1 GIHR-K GIHR-K
NUMBER BOLTS TORQUE
inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm Nm
GIHR 20 DO M16X1.5 0.984 25 1.969 50 9 0.669 17 3.0709 78 0.984 25 1.614 41 0.748 19 M8X20 32
GIHR 25 DO M16X1.5 0.984 25 1.969 50 7 0.669 17 3.071 78 0.984 25 1.614 41 0.906 23 M8X25 32
GIHR 30 DO M22X1.5 1.260 32 2.362 60 6 0.906 23 3.622 92 1.181 30 1.811 46 1.102 28 M8X25 32
GIHR 35 DO M28X1.5 1.575 40 2.756 70 6 1.142 29 4.291 109 1.496 38 2.284 58 1.181 30 M10X30 64
GIHR 40 DO M35X1.5 1.929 49 3.347 85 7 1.417 36 5.197 132 1.772 45 2.598 66 1.378 35 M10X35 64
GIHR 50 DO M45X1.5 2.402 61 4.134 105 6 1.811 46 6.417 163 2.165 55 3.465 88 1.575 40 M12X35 110
GIHR 60 DO M58X1.5 2.953 75 5.118 130 6 2.323 59 7.874 200 2.559 65 3.543 90 1.969 50 M10X45 46
GIHR 70 DO M65X1.5 3.386 86 5.906 150 6 2.598 66 9.134 232 2.953 75 3.937 100 2.165 55 M12X50 80
GIHR 80 DO M80X2 4.016 102 6.693 170 6 3.189 81 10.433 265 3.150 80 4.921 125 2.362 60 M16X50 195
GIHR 90 DO M100X2 4.882 124 8.268 210 5 3.976 101 12.717 323 3.543 90 5.748 146 2.559 65 M16X60 195
GIHR 100 DO M110X2 5.433 138 9.252 235 7 4.370 111 14.173 360 4.134 105 6.535 166 2.756 70 M20X60 385
GIHR 110 DO M120X3 5.984 152 10.433 265 6 4.921 125 16.043 407.5 4.528 115 7.480 190 3.150 80 M20X70 385
GIHR 120 DO M130X3 6.772 172 12.205 310 6 5.315 135 19.291 490 5.512 140 8.543 217 3.543 90 M24X80 660

408
Elges Hydraulic Rod Ends
GK..DO SERIES
D DIN 648, dimension series E
D Sliding contact surfaces: steel/steel

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm
GK 10 DO 0.394 10 0.748 19 0.354 9 1,830 8.15 3,500 15.6 0.09 0.041 0.630 16 0.520 13.2
GK 12 DO 0.472 12 0.866 22 0.394 10 2,430 10.8 4,850 21.6 0.146 0.066 0.709 18 0.587 14.9
GK 15 DO 0.591 15 1.024 26 0.472 12 3,800 17 7,200 32 0.265 0.12 0.866 22 0.724 18.4
GK 17 DO 0.669 17 1.181 30 0.551 14 4,750 21.2 9,000 40 0.353 0.16 0.984 25 0.815 20.7
GK 20 DO 0.787 20 1.378 35 0.630 16 6,700 30 14,600 65 0.507 0.23 1.142 29 0.949 24.1
GK 25 DO 0.984 25 1.654 42 0.787 20 10,800 48 16,200 72 0.948 0.43 1.398 35.5 1.154 29.3
GK 30 DO 1.181 30 1.850 47 0.866 22 13,900 62 21,400 95 1.411 0.64 1.602 40.7 1.347 34.2
GK 35 DO 1.378 35 2.165 55 0.984 25 18,000 80 28,000 125 2.117 0.96 1.850 47 1.563 39.7
GK 40 DO 1.575 40 2.441 62 1.102 28 22,500 100 35,000 156 2.867 1.3 2.087 53 1.772 45
GK 45 DO 1.772 45 2.677 68 1.260 32 28,500 127 47,000 208 3.969 1.8 2.362 60 1.996 50.7
GK 50 DO 1.969 50 2.953 75 1.378 35 35,000 156 56,000 250 5.513 2.5 2.598 66 2.201 55.9
GK 60 DO 2.362 60 3.543 90 1.732 44 55,000 245 88,000 390 8.6 3.9 3.150 80 2.630 66.8
GK 70 DO 2.756 70 4.134 105 1.929 49 71,000 315 115,000 510 14.553 6.6 3.622 92 3.063 77.8
GK 80 DO 3.150 80 4.724 120 2.165 55 90,000 400 139,000 620 19.184 8.7 4.134 105 3.520 89.4

CONTINUED FROM ABOVE

PART d2 d2 d6 d6 h2 h2 C1 C1 ALPHA l6 l6 l7 l7 l8 l8 d7 d7
NUMBER inch mm inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm
GK 10 DO 1.142 29 0.591 15 0.945 24 0.276 7 12 1.516 38.5 0.591 15 0.079 2 0.118 3
GK 12 DO 1.339 34 0.689 17.5 1.063 27 0.315 8 11 1.732 44 0.709 18 0.079 2 0.118 3
GK 15 DO 1.575 40 0.827 21 1.221 31 0.394 10 8 2.008 51 0.787 20 0.098 2.5 0.158 4
GK 17 DO 1.811 46 0.945 24 1.378 35 0.433 11 10 2.284 58 0.906 23 0.118 3 0.158 4
GK 20 DO 2.087 53 1.083 27.5 1.496 38 0.512 13 9 2.539 64.5 1.063 27 0.118 3 0.158 4
GK 25 DO 2.520 64 1.319 33.5 1.772 45 0.669 17 7 3.032 77 1.260 32 0.158 4 0.158 4
GK 30 DO 2.874 73 1.575 40 2.008 51 0.748 19 6 3.445 87.5 1.457 37 0.158 4 0.158 4
GK 35 DO 3.228 82 1.850 47 2.402 61 0.827 21 6 4.016 102 1.654 42 0.158 4 0.158 4
GK 40 DO 3.622 92 2.047 52 2.717 69 0.906 23 7 4.528 115 1.890 48 0.197 5 0.158 4
GK 45 DO 4.016 102 2.284 58 3.032 77 1.063 27 7 5.039 128 2.047 52 0.197 5 0.236 6
GK 50 DO 4.409 112 2.441 62 3.465 88 1.181 30 6 5.669 144 2.362 60 0.236 6 0.236 6
GK 60 DO 5.315 135 2.756 70 3.937 100 1.496 38 6 6.595 167.5 2.953 75 0.315 8 0.236 6
GK 70 DO 6.299 160 3.150 80 4.528 115 1.654 42 6 7.677 195 3.425 87 0.394 10 0.236 6
GK 80 DO 7.087 180 3.740 95 5.551 141 1.850 47 6 9.095 231 3.937 100 0.394 10 0.236 6

409
Elges Hydraulic Rod Ends
GF..DO SERIES
D Sliding contact surfaces: steel/steel
D With rectangular face for welding
D Uses spherical bearing to DIN 648, series E

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk
NUMBER
inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm
GF 20 DO 0.787 20 1.378 35 0.630 16 6,700 30 15,100 67 0.772 0.35 1.142 29
GF 25 DO 0.984 25 1.654 42 0.787 20 10,800 48 15,600 69.5 1.169 0.53 1.398 35.5
GF 30 DO 1.181 30 1.850 47 0.866 22 13,900 62 26,500 118 1.918 0.87 1.602 40.7
GF 35 DO 1.378 35 2.165 55 0.984 25 18,000 80 44,000 196 3.308 1.5 1.850 47
GF 40 DO 1.575 40 2.441 62 1.102 28 22,500 100 67,000 300 5.292 2.4 2.087 53
GF 45 DO 1.772 45 2.677 68 1.260 32 28,500 127 85,000 380 7.497 3.4 2.362 60
GF 50 DO 1.969 50 2.953 75 1.378 35 35,000 156 99,000 440 9.702 4.4 2.598 66
GF 60 DO 2.362 60 3.543 90 1.732 44 55,000 245 128,000 570 15.656 7.1 3.150 80
GF 70 DO 2.756 70 4.134 105 1.929 49 71,000 315 156,000 695 23.153 10.5 3.622 92
GF 80 DO 3.150 80 0.787 20 2.165 55 90,000 400 175,000 780 33.075 15 4.134 105
GF 90 DO 3.543 90 5.118 130 2.362 60 110,000 490 300,000 1340 51.818 23.5 4.528 115
GF 100 DO 3.937 100 5.906 150 2.756 70 137,000 610 335,000 1500 69.458 31.5 5.118 130
GF 110 DO 4.331 110 6.299 160 2.756 70 147,000 655 485,000 2160 105.84 48 5.512 140
GF 120 DO 4.724 120 7.087 180 3.347 85 214,000 950 730,000 3250 174.195 79 6.299 160

CONTINUED FROM ABOVE

PART d1 d1 d2 d2 h2 h2 C1 C1 C1 C1 ALPHA l6 l6
NUMBER nom. nom. max. max. inch
inch mm inch mm inch mm inch mm inch mm deg mm
GF 20 DO 0.949 24.10 1.969 50 1.496 38 0.748 19 0.787 20 9 2.480 63
GF 25 DO 1.154 29.30 2.165 55 1.772 45 0.906 23 0.945 24 7 2.854 72.5
GF 30 DO 1.347 34.20 2.559 65 2.008 51 1.102 28 1.142 29 6 3.287 83.5
GF 35 DO 1.563 39.70 3.268 83 2.402 61 1.181 30 1.221 31 6 4.035 102.5
GF 40 DO 1.772 45.00 3.937 100 2.717 69 1.378 35 1.437 36.5 7 4.685 119
GF 45 DO 1.996 50.70 4.331 110 3.032 77 1.575 40 1.634 41.5 7 5.197 132
GF 50 DO 2.201 55.90 4.843 123 3.465 88 1.575 40 1.634 41.5 6 5.886 149.5
GF 60 DO 2.630 66.80 5.512 140 3.937 100 1.969 50 2.067 52.5 6 6.693 170
GF 70 DO 3.063 77.80 6.457 164 4.528 115 2.165 55 2.284 58 6 7.756 197
GF 80 DO 3.520 89.40 7.087 180 5.551 141 2.362 60 2.480 63 6 9.095 231
GF 90 DO 3.862 98.10 8.898 226 5.906 150 2.559 65 2.717 69 5 10.354 263
GF 100 DO 4.311 109.50 9.843 250 6.693 170 2.756 70 2.913 74 7 11.614 295
GF 110 DO 4.772 121.20 11.614 295 7.284 185 3.150 80 3.347 85 6 13.091 332.5
GF 120 DO 5.335 135.50 14.173 360 8.268 210 3.543 90 3.740 95 6 15.354 390

410
Elges Rod Ends
GIKMR.. SERIES
D DIN 648, dimension series K – ISO 6126
D Sliding contact surfaces: steel/brass
D Internal thread type
D Left hand thread is available on shank, order by replacing “R” with “L”
D Relubricate with funnel type grease nipple

D Replaced by GIKFR..PB series

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2 d3
NUMBER inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIKMR 5 0.197 5 0.315 8 730 3.25 1,280 5.7 0.035 0.016 0.438 11.112 0.303 7.7 0.709 18 M5
GIKMR 6 0.236 6 0.354 9 970 4.3 1,620 7.2 0.049 0.022 0.500 12.7 0.350 8.9 0.787 20 M6
GIKMR 8 0.315 8 0.472 12 1,620 7.2 2,600 11.6 0.104 0.047 0.625 15.875 0.406 10.3 0.945 24 M8
GIKMR 10 0.394 10 0.551 14 2,250 10 3,250 14.5 0.17 0.077 0.750 19.05 0.508 12.9 1.102 28 M10
GIKMR 12 0.472 12 0.630 16 3,000 13.4 3,800 17 0.221 0.1 0.875 22.225 0.606 15.4 1.260 32 M12

CONTINUED FROM ABOVE

PART d4 d4 d5 d5 h1 h1 C1 C1 W W ALPHA l3 l3 l4 l4 l5 l5 l7 l7
NUMBER inch mm inch mm inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm
GIKMR 5 0.335 8.5 0.433 11 1.063 27 0.236 6 0.354 9 13 0.394 10 1.417 36 0.158 4 0.394 10
GIKMR 6 0.394 10 0.512 13 1.181 30 0.266 6.75 0.433 11 13 0.472 12 1.575 40 0.197 5 0.433 11
GIKMR 8 0.492 12.5 0.630 16 1.417 36 0.354 9 0.512 13 13 0.630 16 1.890 48 0.197 5 0.512 13
GIKMR 10 0.591 15 0.748 19 1.693 43 0.413 10.5 0.669 17 13 0.787 20 2.244 57 0.256 6.5 0.591 15
GIKMR 12 0.689 17.5 0.866 22 1.969 50 0.472 12 0.748 19 13 0.866 22 2.598 66 0.256 6.5 0.669 17

411
Elges Rod Ends
GAKMR SERIES
D DIN 648, dimension series K – ISO 6126
D Sliding contact surfaces: steel/brass
D External thread
D Left hand thread is available on shank, order by replacing “R” with “L”
D Relubricate with funnel type grease nipple

D Replaced by GAKFR..PB series

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d B B C C C0 C0 WGT. WGT dk dk
NUMBER inch mm inch mm lbf kN lbf kN lbs kg inch mm
GAKMR 5 0.197 5 0.315 8 730 3.25 700 3.1 0.029 0.013 0.438 11.112
GAKMR 6 0.236 6 0.354 9 970 4.3 990 4.4 0.044 0.02 0.500 12.7
GAKMR 8 0.315 8 0.472 12 1,620 7.2 1,800 8 0.084 0.038 0.625 15.875
GAKMR 10 0.394 10 0.551 14 2,250 10 2,900 12.9 0.121 0.055 0.750 19.05
GAKMR 12 0.472 12 0.630 16 3,000 13.4 3,800 17 0.187 0.085 0.875 22.225

CONTINUED FROM ABOVE

PART d1 d1 d2 d2 d3 h h C1 C1 ALPHA l1 l1 l2 l2
NUMBER inch mm inch mm inch mm inch mm deg inch mm inch mm
GAKMR 5 0.303 7.7 0.709 18 M5 1.299 33 0.236 6 13 0.748 19 1.654 42
GAKMR 6 0.350 8.9 0.787 20 M6 1.417 36 0.266 6.75 13 0.827 21 1.811 46
GAKMR 8 0.406 10.3 0.945 24 M8 1.654 42 0.354 9 13 0.984 25 2.126 54
GAKMR 10 0.508 12.9 1.102 28 M10 1.890 48 0.413 10.5 13 1.102 28 2.441 62
GAKMR 12 0.606 15.4 1.260 32 M12 2.126 54 0.472 12 13 1.260 32 2.756 70

412
Elges Rod Ends
GIKFR..PB SERIES
D DIN 648, dimension series K – ISO 6126
D Sliding contact surfaces: steel/bronze
D Internal thread type
D Left hand thread is available on shank, order by replacing “R” with “L”
D Relubricate with funnel type grease nipple

D Replaces GIKMR.. series

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2 d3
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIKFR 5 PB 0.197 5 0.512 13 0.315 8 730 3.25 1,280 5.7 0.035 0.016 0.4375 11.112 0.303 7.7 0.709 18 M5
GIKFR 6 PB 0.236 6 0.630 16 0.354 9 970 4.3 1,620 7.2 0.049 0.022 0.5 12.7 0.350 8.9 0.787 20 M6
GIKFR 8 PB 0.315 8 0.354 9 0.472 12 1,620 7.2 2,600 11.6 0.104 0.047 0.625 15.875 0.406 10.3 0.945 24 M8
GIKFR 10 PB 0.394 10 0.866 22 0.551 14 2,250 10 3,250 14.5 0.17 0.077 0.75 19.05 0.508 12.9 1.102 28 M10
GIKFR 12 PB 0.472 12 1.024 26 0.630 16 3,000 13.4 3,800 17 0.221 0.1 0.875 22.225 0.606 15.4 1.260 32 M12
GIKFR 14 PB 0.551 14 1.102 28 0.748 19 3,800 17 5,400 24 0.353 0.16 1 25.4 0.661 16.8 1.417 36 M14
GIKFR 16 PB 0.630 16 1.260 32 0.827 21 4,850 21.6 6,400 28.5 0.485 0.22 1.125 28.575 0.760 19.3 1.654 42 M16
GIKFR 18 PB 0.709 18 1.378 35 0.906 23 5,800 26 9,600 42.5 0.706 0.32 1.25 31.75 0.858 21.8 1.811 46 M18X1.5
GIKFR 20 PB 0.787 20 1.575 40 0.984 25 7,100 31.5 9,600 42.5 0.926 0.42 1.375 34.925 0.957 24.3 1.969 50 M20X1.5
GIKFR 22 PB 0.866 22 1.654 42 1.102 28 6,300 28 12,800 57 1.191 0.54 1.5 38.1 1.016 25.8 2.126 54 M22X1.5
GIKFR 25 PB 0.984 25 1.850 47 1.221 31 10,700 47.5 15,300 68 1.61 0.73 1.687 42.85 1.161 29.5 2.362 60 M24X2
GIKFR 30 PB 1.181 30 2.165 55 1.457 37 14,400 64 19,800 88 2.426 1.1 2 50.8 1.370 34.8 2.756 70 M30X2

CONTINUED FROM ABOVE

PART d4 d4 h1 h1 C1 C1 ALPHA l3 l3 l4 l4 l5 l5 l7 l7 d5 d5 W W
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm inch mm
GIKFR 5 PB 0.335 8.5 1.063 27 0.236 6 13 0.394 10 1.417 36 0.158 4 0.394 10 0.433 11 0.354 9
GIKFR 6 PB 0.394 10 1.181 30 0.266 6.75 13 0.472 12 1.575 40 0.197 5 0.433 11 0.512 13 0.433 11
GIKFR 8 PB 0.492 12.5 1.417 36 0.354 9 14 0.630 16 1.890 48 0.197 5 0.512 13 0.630 16 0.551 14
GIKFR 10 PB 0.591 15 1.693 43 0.413 10.5 13 0.787 20 2.244 57 0.256 6.5 0.591 15 0.748 19 0.669 17
GIKFR 12 PB 0.689 17.5 1.969 50 0.472 12 13 0.866 22 2.598 66 0.256 6.5 0.669 17 0.866 22 0.748 19
GIKFR 14 PB 0.827 21 2.244 57 0.532 13.5 16 0.984 25 2.953 75 0.315 8 0.709 18 1.024 26 0.866 22
GIKFR 16 PB 0.866 22 2.520 64 0.591 15 15 1.102 28 3.347 85 0.315 8 0.906 23 1.102 28 0.866 22
GIKFR 18 PB 0.984 25 2.795 71 0.650 16.5 15 1.260 32 3.701 94 0.394 10 0.984 25 1.221 31 1.063 27
GIKFR 20 PB 1.083 27.5 3.032 77 0.709 18 14 1.299 33 4.016 102 0.394 10 1.024 26 1.378 35 1.181 30
GIKFR 22 PB 1.181 30 3.307 84 0.787 20 15 1.457 37 4.370 111 0.472 12 1.142 29 1.496 38 1.260 32
GIKFR 25 PB 1.319 33.5 3.701 94 0.866 22 15 1.654 42 4.882 124 0.472 12 1.260 32 1.654 42 1.417 36
GIKFR 30 PB 1.575 40 4.331 110 0.984 25 17 2.008 51 5.709 145 0.591 15 1.457 37 1.969 50 1.614 41

413
Elges Rod Ends
GAKFR..PB SERIES
D DIN 648, dimension series K – ISO 6126
D Sliding contact surfaces: steel/bronze
D External thread
D Left hand thread is available on shank, order by replacing “R” with “L”
D Relubricate with funnel type grease nipple

D Replaces GAKMR.. series

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm
GAKFR 5 PB 0.197 5 0.512 13 0.315 8 730 3.25 700 3.1 0.029 0.013 0.4375 11.112
GAKFR 6 PB 0.236 6 0.630 16 0.354 9 970 4.3 990 4.4 0.044 0.02 0.5 12.7
GAKFR 8 PB 0.315 8 0.354 9 0.472 12 1620 7.2 1800 8 0.084 0.038 0.625 15.875
GAKFR 10 PB 0.394 10 0.866 22 0.551 14 2250 10 2900 12.9 0.121 0.055 0.75 19.05
GAKFR 12 PB 0.472 12 1.024 26 0.630 16 3000 13.4 3800 17 0.187 0.085 0.875 22.225
GAKFR 14 PB 0.551 14 1.102 28 0.748 19 3800 17 5400 24 0.309 0.14 1 25.4
GAKFR 16 PB 0.630 16 1.260 32 0.827 21 4850 21.6 6400 28.5 0.463 0.21 1.125 28.575
GAKFR 18 PB 0.709 18 1.378 35 0.906 23 5800 26 9600 42.5 0.617 0.28 1.25 31.75
GAKFR 20 PB 0.787 20 1.575 40 0.984 25 7100 31.5 9600 42.5 0.838 0.38 1.375 34.925
GAKFR 22 PB 0.866 22 1.654 42 1.102 28 8500 38 12800 57 1.058 0.48 1.5 38.1
GAKFR 25 PB 0.984 25 1.850 47 1.221 31 10700 47.5 15300 68 1.411 0.64 1.687 42.85
GAKFR 30 PB 1.181 30 2.165 55 1.457 37 14400 64 19800 88 2.426 1.1 2 50.8

CONTINUED FROM ABOVE

PART d1 d1 d2 d2 d3 h h C1 C1 ALPHA l1 l1 l2 l2 l7 l7
NUMBER inch mm inch mm inch mm inch mm deg inch mm inch mm inch mm
GAKFR 5 PB 0.303 7.7 0.709 18 M5 1.299 33 0.236 6 13 0.748 19 1.654 42
GAKFR 6 PB 0.350 8.9 0.787 20 M6 1.417 36 0.266 6.75 13 0.827 21 1.811 46
GAKFR 8 PB 0.406 10.3 0.945 24 M8 1.654 42 0.354 9 14 0.984 25 2.126 54
GAKFR 10 PB 0.508 12.9 1.102 28 M10 1.890 48 0.413 10.5 13 1.102 28 2.441 62
GAKFR 12 PB 0.606 15.4 1.260 32 M12 2.126 54 0.472 12 13 1.260 32 2.756 70
GAKFR 14 PB 0.661 16.8 1.417 36 M14 2.362 60 0.532 13.5 16 1.417 36 3.071 78 0.709 18
GAKFR 16 PB 0.760 19.3 1.654 42 M16 2.598 66 0.591 15 15 1.457 37 3.425 87 0.906 23
GAKFR 18 PB 0.858 21.8 1.811 46 M18X1.5 2.835 72 0.650 16.5 15 1.614 41 3.740 95 0.984 25
GAKFR 20 PB 0.957 24.3 1.969 50 M20X1.5 3.071 78 0.709 18 14 1.772 45 4.055 103 1.024 26
GAKFR 22 PB 1.016 25.8 2.126 54 M22X1.5 3.307 84 0.787 20 15 1.890 48 4.370 111 1.142 29
GAKFR 25 PB 1.161 29.5 2.362 60 M24X2 3.701 94 0.866 22 15 2.165 55 4.882 124 1.260 32
GAKFR 30 PB 1.370 34.8 2.756 70 M30X2 4.331 110 0.984 25 17 2.598 66 5.709 145 1.457 37

414
Elges Rod Ends,
Maintenance Free
GIR..UK, GIR..UK-2RS SERIES
D DIN 648, dimension series E – ISO 6126
D Sliding contact surfaces: hard chrome/PTFE
D Internal thread
D Left hand thread is available on shank, order by replacing “R” with “L”

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIR 6 UK 0.236 6 0.551 14 0.236 6 810 3.6 1,830 8.15 0.046 0.021 0.394 10 0.315 8 0.827 21
GIR 8 UK 0.315 8 0.630 16 0.315 8 1,320 5.85 2,900 12.9 0.086 0.039 0.512 13 0.402 10.2 0.945 24
GIR 10 UK 0.394 10 0.748 19 0.354 9 1,950 8.65 3,950 17.6 0.135 0.061 0.630 16 0.520 13.2 1.142 29
GIR 12 UK 0.472 12 0.866 22 0.394 10 2,550 11.4 5,500 24.5 2.117 0.96 0.709 18 0.587 14.9 1.339 34
GIR 15 UK 0.591 15 1.024 26 0.472 12 3,950 17.6 8,100 36 0.397 0.18 0.866 22 0.724 18.4 1.575 40
GIR 17 UK 0.669 17 1.181 30 0.551 14 5,000 22.4 10,100 45 0.485 0.22 0.984 25 0.815 20.7 1.811 46
GIR 20 UK 0.787 20 1.378 35 0.630 16 7,100 31.5 13,500 60 0.772 0.35 1.142 29 0.949 24.1 2.087 53
GIR 25 UK 0.984 25 1.654 42 0.787 20 11,500 51 18,700 83 1.411 0.64 1.398 35.5 1.154 29.3 2.520 64
GIR 30 UK 1.181 30 1.850 47 0.866 22 15,000 66.5 24,700 110 2.051 0.93 1.602 40.7 1.347 34.2 2.874 73
GIR 35 UK2RS 1.378 35 2.165 55 0.984 25 25,000 112 33,000 146 2.867 1.3 1.850 47 1.563 39.7 3.228 82
GIR 40 UK2RS 1.575 40 2.441 62 1.102 28 31,500 140 40,500 180 4.41 2 2.087 53 1.772 45 3.622 92
GIR 45 UK2RS 1.772 45 2.677 68 1.260 32 40,500 180 54,000 240 5.513 2.5 2.362 60 1.996 50.7 4.016 102
GIR 50 UK2RS 1.969 50 2.953 75 1.378 35 49,500 220 65,000 290 7.718 3.5 2.598 66 2.201 55.9 4.409 112
GIR 60 UK2RS 2.362 60 3.543 90 1.732 44 78,000 345 101,000 450 12.128 5.5 3.150 80 2.630 66.8 5.315 135
GIR 70 UK2RS 2.756 70 4.134 105 1.929 49 99,000 440 137,000 610 18.963 8.6 3.622 92 3.063 77.8 6.299 160
GIR 80 UK2RS 3.150 80 4.724 120 2.165 55 128,000 570 169,000 750 26.46 12 4.134 105 3.520 89.4 7.087 180

CONTINUED FROM ABOVE

PART d3 d4 d4 h1 h1 C1 C1 ALPHA l3 l3 l4 l4 l7 l7 d5 d5 W W
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm
GIR 6 UK M6 0.394 10 1.181 30 0.173 4.4 13 0.433 11 1.595 40.5 0.472 12 0.512 13 0.433 11
GIR 8 UK M8 0.492 12.5 1.417 36 0.236 6 15 0.591 15 1.890 48 0.551 14 0.630 16 0.551 14
GIR 10 UK M10 0.591 15 1.693 43 0.276 7 12 0.787 20 2.264 57.5 0.591 15 0.748 19 0.669 17
GIR 12 UK M12 0.689 17.5 1.969 50 0.315 8 11 0.906 23 2.638 67 0.709 18 0.866 22 0.748 19
GIR 15 UK M14 0.827 21 2.402 61 0.394 10 8 1.181 30 3.189 81 0.787 20 1.024 26 0.866 22
GIR 17 UK M16 0.945 24 2.638 67 0.433 11 10 1.339 34 3.543 90 0.906 23 1.181 30 1.063 27
GIR 20 UK M20X1.5 1.083 27.5 3.032 77 0.512 13 9 1.575 40 4.075 103.5 1.063 27 1.378 35 1.260 32
GIR 25 UK M24X2 1.319 33.5 3.701 94 0.669 17 7 1.890 48 4.961 126 1.260 32 1.654 42 1.417 36
GIR 30 UK M30X2 1.575 40 4.331 110 0.748 19 6 2.205 56 5.768 146.5 1.457 37 1.969 50 1.614 41
GIR 35 UK2RS M36X3 1.850 47 4.921 125 0.827 21 6 2.362 60 6.535 166 1.654 42 2.284 58 1.969 50
GIR 40 UK2RS M39X3 2.047 52 5.591 142 0.906 23 7 2.559 65 7.402 188 1.890 48 2.559 65 2.165 55
GIR 45 UK2RS M42X3 2.284 58 5.709 145 1.063 27 7 2.559 65 7.717 196 2.047 52 2.756 70 2.362 60
GIR 50 UK2RS M45X3 2.441 62 6.299 160 1.181 30 6 2.677 68 8.504 216 2.362 60 2.953 75 2.559 65
GIR 60 UK2RS M52X3 2.756 70 6.890 175 1.496 38 6 2.756 70 9.547 242.5 2.953 75 3.465 88 2.953 75
GIR 70 UK2RS M56X4 3.150 80 7.874 200 1.654 42 6 3.150 80 11.024 280 3.425 87 3.858 98 3.347 85
GIR 80 UK2RS M64X4 3.740 95 9.055 230 1.850 47 6 3.347 85 12.598 320 3.937 100 4.331 110 3.937 100

415
Elges Rod Ends,
Maintenance Free
GAR..UK, GAR..UK-2RS SERIES
D DIN 648, dimension series E Form A – ISO 6126
D Sliding contact surfaces: hard chromium/PTFE
D External thread
D Left hand thread is available on shank, order by replacing “R” with “L”

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm
GAR 6 UK 0.236 6 0.551 14 0.236 6 810 3.6 1,830 8.15 0.037 0.017 0.394 10
GAR 8 UK 0.315 8 0.630 16 0.315 8 1,320 5.85 2,900 12.9 0.064 0.029 0.512 13
GAR 10 UK 0.394 10 0.748 19 0.354 9 1,950 8.65 3,950 17.6 0.112 0.051 0.630 16
GAR 12 UK 0.472 12 0.866 22 0.394 10 2,550 11.4 5,500 24.5 0.19 0.086 0.709 18
GAR 15 UK 0.591 15 1.024 26 0.472 12 3,950 17.6 8,100 36 0.309 0.14 0.866 22
GAR 17 UK 0.669 17 1.181 30 0.551 14 5,000 22.4 10,100 45 0.419 0.19 0.984 25
GAR 20 UK 0.787 20 1.378 35 0.630 16 7,100 31.5 13,500 60 0.684 0.31 1.142 29
GAR 25 UK 0.984 25 1.654 42 0.787 20 11,500 51 18,700 83 1.235 0.56 1.398 35.5
GAR 30 UK 1.181 30 1.850 47 0.866 22 14,700 65.5 24,700 110 1.962 0.89 1.602 40.7
GAR 35 UK2RS 1.378 35 2.165 55 0.984 25 25,000 112 33,000 146 3.087 1.4 1.850 47
GAR 40 UK2RS 1.575 40 2.441 62 1.102 28 31,500 140 40,500 180 3.969 1.8 2.087 53
GAR 45 UK2RS 1.772 45 2.677 68 1.260 32 40,500 180 54,000 240 5.733 2.6 2.362 60
GAR 50 UK2RS 1.969 50 2.953 75 1.378 35 49,500 220 65,000 290 7.497 3.4 2.598 66
GAR 60 UK2RS 2.362 60 3.543 90 1.732 44 78,000 345 101,000 450 13.01 5.9 3.150 80
GAR 70 UK2RS 2.756 70 4.134 105 1.929 49 99,000 440 137,000 610 18.081 8.2 3.622 92
GAR 80 UK2RS 3.150 80 4.724 120 2.165 55 128,000 570 169,000 750 26.46 12 4.134 105

CONTINUED FROM ABOVE

PART d1 d1 d2 d2 d3 h h C1 C1 ALPHA l1 l1 l2 l2 l7 l7
NUMBER inch mm inch mm inch mm inch mm deg inch mm inch mm inch mm
GAR 6 UK 0.315 8 0.827 21 M6 1.417 36 0.173 4.4 13 0.709 18 1.831 46.5 0.472 12
GAR 8 UK 0.402 10.2 0.945 24 M8 1.654 42 0.236 6 15 0.866 22 2.126 54 0.551 14
GAR 10 UK 0.520 13.2 1.142 29 M10 1.890 48 0.276 7 12 1.024 26 2.461 62.5 0.591 15
GAR 12 UK 0.587 14.9 1.339 34 M12 2.126 54 0.315 8 11 1.102 28 2.795 71 0.709 18
GAR 15 UK 0.724 18.4 1.575 40 M14 2.480 63 0.394 10 8 1.339 34 3.268 83 0.787 20
GAR 17 UK 0.815 20.7 1.811 46 M16 2.717 69 0.433 11 10 1.417 36 3.622 92 0.906 23
GAR 20 UK 0.949 24.1 2.087 53 M20X1.5 3.071 78 0.512 13 9 1.693 43 4.114 104.5 1.063 27
GAR 25 UK 1.154 29.3 2.520 64 M24X2 3.701 94 0.669 17 7 2.087 53 4.961 126 1.260 32
GAR 30 UK 1.347 34.2 2.874 73 M30X2 4.331 110 0.748 19 6 2.559 65 5.768 146.5 1.457 37
GAR 35 UK2RS 1.563 39.7 3.228 82 M36X3 5.512 140 0.827 21 6 3.228 82 7.126 181 1.654 42
GAR 40 UK2RS 1.772 45 3.622 92 M39X3 5.906 150 0.906 23 7 3.386 86 7.717 196 1.890 48
GAR 45 UK2RS 1.996 50.7 4.016 102 M42X3 6.417 163 1.063 27 7 3.701 94 8.425 214 2.047 52
GAR 50 UK2RS 2.201 55.9 4.409 112 M45X3 7.284 185 1.181 30 6 4.213 107 9.488 241 2.362 60
GAR 60 UK2RS 2.630 66.8 5.315 135 M52X3 8.268 210 1.496 38 6 4.528 115 10.925 277.5 2.953 75
GAR 70 UK2RS 3.063 77.8 6.299 160 M56X4 9.252 235 1.654 42 6 4.921 125 12.402 315 3.307 84
GAR 80 UK2RS 3.520 89.4 7.087 180 M64X4 10.630 270 1.850 47 6 5.512 140 14.173 360 3.937 100

416
Elges Rod Ends,
Maintenance Free
GIKFR..PW, GIPFR..PW SERIES
D DIN 648, dimension series K – ISO 6126
D Sliding contact surfaces: steel/PTFE Foil
D Internal thread
D Left hand thread is available on shank, order by replacing “R” with “L”
D GIPFR series has fine pitch threads to fit hydraulic cylinders to DIN 24335

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk d1 d1 d2 d2 d3
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm inch mm inch mm
GIKFR 5 PW 0.197 5 0.512 13 0.315 8 1,350 6 1,280 5.7 0.035 0.016 0.438 11.112 0.303 7.7 0.709 18 M5
GIPFR 5 PW 0.197 5 0.512 13 0.315 8 1,350 6 1,280 5.7 0.035 0.016 0.438 11.112 0.303 7.7 0.709 18 M4
GIKFR 6 PW 0.236 6 0.630 16 0.354 9 1,720 7.65 1,620 7.2 0.049 0.022 0.500 12.7 0.350 8.9 0.787 20 M6
GIKFR 8 PW 0.315 8 0.748 19 0.472 12 2,900 12.9 2,600 11.6 0.104 0.047 0.625 15.875 0.406 10.3 0.945 24 M8
GIKFR 10 PW 0.394 10 0.866 22 0.551 14 4,050 18 3,250 14.5 0.17 0.077 0.750 19.05 0.508 12.9 1.102 28 M10
GIPFR 10 PW 0.394 10 0.866 22 0.551 14 4,050 18 3,250 14.5 0.17 0.077 0.750 19.05 0.508 12.9 1.102 28 M10X1.25
GIKFR 12 PW 0.472 12 1.024 26 0.630 16 5,400 24 3,800 17 0.221 0.1 0.875 22.225 0.606 15.4 1.260 32 M12
GIPFR 12 PW 0.472 12 1.024 26 0.630 16 5,400 24 3,800 17 0.221 0.1 0.875 22.225 0.606 15.4 1.260 32 M12X1.25
GIKFR 14 PW 0.551 14 1.102 28 0.748 19 7,000 31 5,400 24 0.353 0.16 1.000 25.4 0.661 16.8 1.417 36 M14
GIKFR 16 PW 0.630 16 1.260 32 0.827 21 8,800 39 6,400 28.5 0.485 0.22 1.125 28.575 0.760 19.3 1.654 42 M16
GIPFR 16 PW 0.630 16 1.260 32 0.827 21 8,800 39 6,400 28.5 0.485 0.22 1.125 28.575 0.760 19.3 1.654 42 M16X1.5
GIKFR 18 PW 0.709 18 1.378 35 0.906 23 10,700 47.5 9,600 42.5 0.706 0.32 1.250 31.75 0.858 21.8 1.811 46 M18X1.5
GIKFR 20 PW 0.787 20 1.575 40 0.984 25 12,800 57 9,600 42.5 0.926 0.42 1.375 34.925 0.957 24.3 1.969 50 M20X1.5
GIKFR 22 PW 0.866 22 1.654 42 1.102 28 15,300 68 12,800 57 1.191 0.54 1.500 38.1 1.016 25.8 2.126 54 M22X1.5
GIKFR 25 PW 0.984 25 1.850 47 1.221 31 19,100 85 15,300 68 1.61 0.73 1.687 42.85 1.161 29.5 2.362 60 M24X2
GIKFR 30 PW 1.181 30 2.165 55 1.457 37 25,500 114 19,800 88 2.426 1.1 2.000 50.8 1.370 34.8 2.756 70 M30X2
GIPFR 30 PW 1.181 30 2.165 55 1.457 37 25,500 114 19,800 88 2.426 1.1 2.000 50.8 1.370 34.8 2.756 70 M27X2

CONTINUED FROM ABOVE

PART d4 d4 h1 h1 C1 C1 ALPHA l3 l3 l4 l4 l5 l5 l7 l7 d5 d5 W W
NUMBER inch mm inch mm inch mm deg inch mm inch mm inch mm inch mm inch mm inch mm
GIKFR 5 PW 0.335 8.5 1.063 27 0.236 6 13 0.394 10 1.417 36 0.158 4 0.394 10 0.433 11 0.354 9
GIPFR 5 PW 0.335 8.5 1.063 27 0.236 6 13 0.394 10 1.417 36 0.158 4 0.394 10 0.433 11 0.354 9
GIKFR 6 PW 0.394 10 1.181 30 0.266 6.75 13 0.472 12 1.575 40 0.197 5 0.433 11 0.512 13 0.433 11
GIKFR 8 PW 0.492 12.5 1.417 36 0.354 9 14 0.630 16 1.890 48 0.197 5 0.512 13 0.630 16 0.551 14
GIKFR 10 PW 0.591 15 1.693 43 0.413 10.5 13 0.787 20 2.244 57 0.256 6.5 0.591 15 0.748 19 0.669 17
GIPFR 10 PW 0.591 15 1.693 43 0.413 10.5 13 0.787 20 2.244 57 0.256 6.5 0.591 15 0.748 19 0.669 17
GIKFR 12 PW 0.689 17.5 1.969 50 0.472 12 13 0.866 22 2.598 66 0.256 6.5 0.669 17 0.866 22 0.748 19
GIPFR 12 PW 0.689 17.5 1.969 50 0.472 12 13 0.866 22 2.598 66 0.256 6.5 0.669 17 0.866 22 0.748 19
GIKFR 14 PW 0.827 21 2.244 57 0.532 13.5 16 0.984 25 2.953 75 0.315 8 0.709 18 1.024 26 0.866 22
GIKFR 16 PW 0.866 22 2.520 64 0.591 15 15 1.102 28 3.347 85 0.315 8 0.906 23 1.102 28 0.866 22
GIPFR 16 PW 0.866 22 2.520 64 0.591 15 15 1.102 28 3.347 85 0.315 8 0.906 23 1.102 28 0.866 22
GIKFR 18 PW 0.984 25 2.795 71 0.650 16.5 15 1.260 32 3.701 94 0.394 10 0.984 25 1.221 31 1.063 27
GIKFR 20 PW 1.083 27.5 3.032 77 0.709 18 14 1.299 33 4.016 102 0.394 10 1.024 26 1.378 35 1.181 30
GIKFR 22 PW 1.181 30 3.307 84 0.787 20 15 1.457 37 4.370 111 0.472 12 1.142 29 1.496 38 1.260 32
GIKFR 25 PW 1.319 33.5 3.701 94 0.866 22 15 1.654 42 4.882 124 0.472 12 1.260 32 1.654 42 1.417 36
GIKFR 30 PW 1.575 40 4.331 110 0.984 25 17 2.008 51 5.709 145 0.591 15 1.457 37 1.969 50 1.614 41
GIPFR 30 PW 1.575 40 4.331 110 0.984 25 17 2.008 51 5.709 145 0.591 15 1.457 37 1.969 50 1.614 41

417
Elges Rod Ends,
Maintenance Free
GAKFR..PW SERIES
D DIN 648, dimension series K – ISO 6126
D Sliding contact surfaces: steel/PTFE
D External thread
D Left hand thread is available on shank, order by replacing “R” with “L”

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section.
For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.
PART d d D D B B C C C0 C0 WGT. WGT dk dk
NUMBER inch mm inch mm inch mm lbf kN lbf kN lbs kg inch mm
GAKFR 5 PW 0.1969 5 0.5118 13 0.315 8 1350 6 700 3.1 0.029 0.013 0.4375 11.112
GAKFR 6 PW 0.2362 6 0.6299 16 0.3543 9 1720 7.65 990 4.4 0.044 0.02 0.5 12.7
GAKFR 8 PW 0.315 8 0.748 19 0.4724 12 2900 12.9 1800 8 0.084 0.038 0.625 15.875
GAKFR 10 PW 0.3937 10 0.8661 22 0.5512 14 4050 18 2900 12.9 0.121 0.055 0.75 19.05
GAKFR 12 PW 0.4724 12 1.0236 26 0.6299 16 5400 24 3800 17 0.187 0.085 0.875 22.225
GAKFR 14 PW 0.5512 14 1.1024 28 0.748 19 7000 31 4700 21 0.309 0.14 1 25.4
GAKFR 16 PW 0.6299 16 1.2598 32 0.8268 21 8800 39 6400 28.5 0.463 0.21 1.125 28.575
GAKFR 18 PW 0.7087 18 1.378 35 0.9055 23 10700 47.5 9600 42.5 0.617 0.28 1.25 31.75
GAKFR 20 PW 0.7874 20 1.5748 40 0.9843 25 12800 57 9600 42.5 0.838 0.38 1.375 34.925
GAKFR 22 PW 0.8661 22 1.6535 42 1.1024 28 15300 68 12800 57 1.058 0.48 1.5 38.1
GAKFR 25 PW 0.9843 25 1.8504 47 1.2205 31 19100 85 15300 68 1.411 0.64 1.687 42.85
GAKFR 30 PW 1.1811 30 2.1654 55 1.4567 37 25500 114 19800 88 2.426 1.1 2 50.8

CONTINUED FROM ABOVE

PART d1 d1 d2 d2 d3 h h C1 C1 ALPHA l1 l1 l2 l2 l7 l7
NUMBER inch mm inch mm inch mm inch mm deg inch mm inch mm inch mm
GAKFR 5 PW 0.3031 7.7 0.7087 18 M5 1.2992 33 0.2362 6 13 0.748 19 1.6535 42
GAKFR 6 PW 0.3504 8.9 0.7874 20 M6 1.4173 36 0.2657 6.75 13 0.8268 21 1.811 46
GAKFR 8 PW 0.4055 10.3 0.9449 24 M8 1.6535 42 0.3543 9 14 0.9843 25 2.126 54
GAKFR 10 PW 0.5079 12.9 1.1024 28 M10 1.8898 48 0.4134 10.5 13 1.1024 28 2.4409 62
GAKFR 12 PW 0.6063 15.4 1.2598 32 M12 2.126 54 0.4724 12 13 1.2598 32 2.7559 70
GAKFR 14 PW 0.6614 16.8 1.4173 36 M14 2.3622 60 0.5315 13.5 16 1.4173 36 3.0709 78 0.7087 18
GAKFR 16 PW 0.7598 19.3 1.6535 42 M16 2.5984 66 0.5906 15 15 1.4567 37 3.4252 87 0.9055 23
GAKFR 18 PW 0.8583 21.8 1.811 46 M18X1.5 2.8346 72 0.6496 16.5 15 1.6142 41 3.7402 95 0.9843 25
GAKFR 20 PW 0.9567 24.3 1.9685 50 M20X1.5 3.0709 78 0.7087 18 14 1.7717 45 4.0551 103 1.0236 26
GAKFR 22 PW 1.0157 25.8 2.126 54 M22X1.5 3.3071 84 0.7874 20 15 1.8898 48 4.3701 111 1.1417 29
GAKFR 25 PW 1.1614 29.5 2.3622 60 M24X2 3.7008 94 0.8661 22 15 2.1654 55 4.8819 124 1.2598 32
GAKFR 30 PW 1.3701 34.8 2.7559 70 M30X2 4.3307 110 0.9843 25 17 2.5984 66 5.7087 145 1.4567 37

418
NOTES

419
420
INA SALES OFFICES
MANUFACTURING PLANTS

SALES OFFICES MANUFACTURING PLANTS

TORONTO, CANADA PARENT COMPANY UNITED STATES

INA Canada Inc. INA Waelzlager Schaeffler oHG PLANT I
2871 Plymouth Drive Industriestrasse 1-3 INA USA Corporation
Oakville, Ontario L6H 5S5 P.O. Box 1220 One INA Drive
Toll Free: 800-263-4397 D-91074 Herzogenaurach P.O. Box 390
Germany Cheraw, South Carolina 29520
Telephone: 905-829-2750 Telephone: (49132) 82-0 Telephone: 843-537-9341/9346
Fax: 905-829-2563 Fax: (49132) 82 49 33 Fax: 843-537-8751
MONTREAL, CANADA
INA Canada Inc. PLANT II
149 Avenue Guthrie INA USA Corporation
Dorval, Quebec H9P 2P1 Highway 9 West
Toll Free: 800-361-7015 P.O. Box 390
Cheraw, South Carolina 29520
Telephone: 514-631-2214 Telephone: 843-537-9341
Fax: 514-631-9571 Fax: 843-537-8752

VANCOUVER, CANADA
INA Canada Inc. PLANT III
106-1668 Derwent Way INA USA Corporation
Delta, British Columbia, V3M R9 308 Springhill Farm Road
Toll Free: 800-663-9006 Fort Mill, South Carolina 29715
Telephone: 803-547-7990
Telephone: 604-526-3500 Fax: 803-548-8597
Fax: 604-526-6544

MEXICO CITY, MEXICO PLANT IV

INA USA Corporation
INA Mexico, S.A. de C.V. New Cut Road, P.O. Box 570
Paseo de la Reforma 383-704 Spartanburg, South Carolina 29304
Col. Cuauhtemoc Telephone: 864-583-4541
06500 Mexico D.F. Fax: 864-591-8890
Telephone: 525-525-00-12 / 01-84
Fax: 525-525-01-94
PLANT V
OTHER COUNTRIES INA USA Corporation
Argentina Italy 200 Evans Row
Australia Japan Cheraw, South Carolina 29520
Austria Korea Telephone: 843-537-9341
Belgium Netherlands Fax: 843-537-8751
Brazil Norway
Denmark Portugal OTHER COUNTRIES
Finland South Africa
France Spain Australia Great Britain
Germany Sweden Brazil Italy
Great Britain Turkey Canada Korea
China Slovakia
France Spain
Germany Switzerland
 TABLE OF CONTENTS
Corporate Offices
INA USA CORPORATION
308 Springhill Farm Road
Fort Mill, South Carolina 29715
Telephone: 803-548-8500 Fax: 803-548-8599
INA LINEAR TECHNIK
A Division Of INA USA Corporation
247 Rittenhouse Circle
Bristol, Pennsylvania 19007
USA SALES OFFICES Telephone: 215-781-6900 Fax: 215-781-9830

ATLANTA HARTFORD PHILADELPHIA

1870 The Exchange, Suite 100 1799 Farmington Ave., Bldg. B-2, P.O. Box 528 3399 Progress Drive
Atlanta, Georgia 30339 Unionville, Connecticut 06085 Bensalem, Pennsylvania 19020
Telephone: 770-951-7015 Telephone: 860-673-5236 Telephone: 215-245-3485
Fax: 770-951-7092 Fax: 860-673-5270 Fax: 215-245-7779
BUFFALO HOUSTON PHOENIX
336 Harris Hill Road, Suite 100 10101 Southwest Freeway, Suite 400 11024 N. 28th Street, Suite 208
Williamsville, New York 14221 Houston, Texas 77074 Phoenix, Arizona 85029
Telephone: 716-631-1533 Telephone: 713-219-1430 Telephone: 602-588–9304
Fax: 716-631-8741 Fax: 713-219-1431 Fax: 602-588–9318
CHARLOTTE INDIANAPOLIS QUAD CITIES
377 Carowinds Boulevard, Suite 120 7301 Elm Ridge Road 300 Northwest Banktower
Fort Mill, South Carolina 29708 Indianapolis, Indiana 46236 2550 Middle Road Bettendorf, Iowa 52722
Telephone: 803-547-7970 Telephone: 317-823-7268 Telephone: 319-355-0383
Fax: 803-548-6361 Fax: 317-823-7269 Fax: 319-355-1937
CHICAGO KANSAS CITY RICHMOND
2525 Cabot Drive, Suite 202 4201 N.E. Lakewood Way, Suite 101 8003 Franklin Farms Drive, Suite 229B
Lisle, Illinois 60532 Lee’s Summit, Missouri 64064 Richmond, Virginia 23229
Telephone: 630-955-9360 Telephone: 816-795-9311 Telephone: 804-527-0901
Fax: 630-955-9365 Fax: 816-795-9322 Fax: 804-527-0992
CLEVELAND LOS ANGELES SAN FRANCISCO
12306 Woodward Boulevard 767 North Main Street 3478 Buskirk Avenue, Suite 1043
Garfield Heights, Ohio 44125 Orange, California 92868 Pleasant Hill, California 94523
Telephone: 216-587-4393 Telephone: 714-744-1022 Telephone: 925-746-7103
Fax: 216-587-2655 Fax: 714-744-2640 Fax: 925-946-9936
DALLAS LOUISVILLE SEATTLE
3939 Belt Line Road, Suite 365 14419 Micawber Way 40 Lake Bellevue, Suite 100
Addison, Texas 75001 Louisville, Kentucky 40245 Bellevue, Washington 98005
Telephone: 972-488-2544 Telephone: 502-254-9590 Telephone: 425-646-9477
Fax: 972-488-2802 Fax: 502-254-2760 Fax: 425-646-9471
DAYTON MEMPHIS TAMPA
261 Regency Ridge Drive 1922 Exeter Road, Suite 20 25327 Celmar Street
Centerville, Ohio 45459 Germantown, Tennessee 38138 Brooksville, Florida 34601
Telephone: 937-433-6404 Telephone: 901-756-0023 Telephone: 352-797-0620
Fax: 937-433-6814 Fax: 901-756-0260 Fax: 352-797-0630
DETROIT MILWAUKEE
335 East Big Beaver Road, Suite 101 N16 W23233 Stoneridge Drive, Suite 220
Troy, Michigan 48083 Waukesha, Wisconsin 53188
Telephone: 248-528-9080 Telephone: 414-544-8270
Fax: 248-619-2139 Fax: 414-544-8271
FLINT MINNEAPOLIS
771A E. Main Street, P.O. Box 666 80 W. 78th Street, Suite 270C
Flushing, Michigan 48433 Chanhassen, Minnesota 55317
Telephone: 810-659-3607 Telephone: 612-934-8822
Fax: 810-659-4771 Fax: 612-934-8833