0 ratings0% found this document useful (0 votes) 762 views7 pagesCSEC Technical Drawing (Machanical) 2019 Paper 02
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content,
claim it here.
Available Formats
Download as PDF or read online on Scribd
- General Information: Provides general instructions regarding the examination paper and drawing methods to be used.
- Section I – Assembly Drawing: Contains tasks and instructions for creating assembly drawings based on provided figures and specifications.
- Section II – Sketch and Design: Instructs candidates to create orthographic sketches to illustrate specified engineering conventions.
& test cove 01347022
FORM TP 2019124 MAYJUNE 2019
CARIBBEAN EXAMINATIONS COUNCIL
CARIBBEAN SECONDARY EDUCATION CERTIFICATE®
EXAMINATION
‘TECHNICAL DRAWING
OPTION B ~MECHANICAL ENGINEERING DRAWING
Paper 02 — General Proficiency
‘2 hours 40 minutes
GENERAL INFORMATION
Each candidate should have the following for this examination:
(a) Traditional Drawing Method
Two sheets of drawing paper (both sides may be used)
Drawing instruments
Drawing board and T-square
Metric scale rule
(b) Computer-Aided Drafting Method
A minimum of three sheets of 11" « 17" paper
Personal computer with monitor, keyboard, mouse and printer
Computer-Aided Drafting software
807
NOTE: Atter completing RACH question, save your work electronically on the available
storage device. At the conclusion of the examination, the invigilator will give
you instructions for submitting the saved files,
All dimensions are given in millimetres unless otherwise stated.
3. When first angle oF third angle is not specified, the choiee of projection is left to the candidate's
discretion, in which case the type of projection used MUST be clearly stated,
§
4. Where scales to be employed are not stated, the full size should be epplied.
5. Each candidate should use histher awn judgement to supply any dimension or detail not directly
shown on the drawings.
6. ‘The number of each question answered MUST be written next to the solution
7. Each candidate MUST emter his/her school code and regisir
Wn number in the appropriate space
at the bottom right-hand comer of each page.
8. All geometrical construction lines MUST be visible on all answers submitted for BOTH Traditional
Drawing and Computer-Aided Drafting Methods.
9. You are advised to take some time to read through the paper and plan your answers.
DO NOT TURN THIS PAGE UNTIL YOU ARE TOLD TO DO SO
Copyright © 2018 Caribbean Pxaminations Councit
Albrights reserved.
01347022/MNICSEC 2019
NAPARIMA GRLB' HIGH SCHOQ, } sur
oss
-2-
MECHANICAL ENGINEER!
§ DRAWING
“This paper consists of TWO questions divided into TWO sections: Sei
Section H, Sketch and Design. Answer BOTH questions,
mn l,Assembly Drawing and
Candidates MAY use EITHER the Traditional Drawing Method OR the Computer-Aided Drafting
Method.
SECTION I - ASSEMBLY DRAWING
Do NOT spend more than 2 hours on this section,
1. Figure 1, on the enclosed sheet, shows the first angle orthographic projection details of the parts
that make up a bearing housing assembly. In assembly, the bearing clamp (2) is secured to the
bearing, bracket (1) and held in place by two bolls (5), Two bushings (4) are positioned on either
end of the housing assembly. The pin (3) is fitted into the assembly bearing bracket (1) and bearing,
‘clamp (2) and is held in position by the bushings (4).
(2) Draw, FULLSIZE, in either first angle ot third angle orthographic projection, the following
views of the assembly:
()— Affunt elevation, Show all hidden details.
(ii) A full sectional end elevation on cutting plane ‘Z-Z"
(») Show SIX main dimensions to include a length, a diameter, a radius and a metric screw
thread specification
{c) Print the title, “Beating Housing Assembly”, and the scale used. Indicate the projection
method used hy symbol.
a1 90 marks
GO ON TO THE NEXT PAGE,
01347022/MICSEC 2019 vest cone 01347022
MAYAIUNE 2019
[ATIONS COUNCIL
YUCATION CERTIFICATE?
ATION
DRAWING
NICAL DRAWING
sal Proficiency
Centre Now
ae back of this sheet. 150 -
80 .
50
2HOLES —~
Maxie
DEEP
4 HOLES
Gis
950 o |
kt |
|
2 HOLES
ou
L |
}
Rp
1 18 |
! oO A= -
oft)
| 38
| ® BOLT @ off) |
MIO X 38 !
BEARING HOUSING
ALL DIMENSIONS IN mm
Seale =:
=e} FORM TP 2019124
Candidate Nos .
g
CARIBBEAN EXAM
CARIBBEAN SECONDARY
EXAMI
TECHNICA
OPTION B-MECI
Puper 02 ~ Ge
Please see Figure 1 ¢ sor
A003
3.
SECTION Il - SKETCH AND DESIGN
Do NOT spend more than 30 minutes on this section,
2, Make neat, proportional octhographic sketches to illustrate the specified engineering conventions
in each of the following:
fa) Orthographic elevations/views to illustrate
@
mond kau
Gi) External threading
1) Orthographic sectional views to iMustrate
(Internal threading
Gi) Countersunk hole
Gili) Counterbored hale
Total 30 marks
END OF TEST
IF YOU FINISH BEFORF. TIME IS CALLED, CHECK YOUR WORK ON THIS TEST.
01347022/MNCSEC 2019
