2-way pressure reducing valve

DMM10121-12

up to   25 l/min spool type, direct-acting

up to 450 bar Metric Cartridge – 450 bar
FUNCTION PRODUCT ADVANTAGES
z Optimum control behaviour
z Low hysteresis
z High repeatability
z Extremely low leakage in seat-tight control position
z Very compact design
z Adjustable range up to 320 bar
z Also available as a low-temperature version
z Exposed surfaces zinc-nickel plated for increased corrosion protection (1,000 h
salt spray test)

FUNCTION DESCRIPTION
The pressure reducing valve is a 2-way pressure valve. It reduces an inlet pressure at
port 1 to a lower outlet pressure for the consumer at port 2. The level of the reduced
outlet pressure can be set at the valve. When the pressure value at port 2 reaches the
pressure setting, the valve closes leak-free at the control point which prevents leakage at
the consumer. Port 3 serves to relieve the pressure of the spring chamber to the tank.
NOTICE:
The tank pressure adds to the set pressure.
The valve is primary pressure-dependent.

EN 5.169.13.0/07.20

1
 SPECIFICATIONS*
Operating pressure max. 450 bar (max. supply pressure at port 1)
Pressure balance See typical performance
Tank pressure (port 3) max. 30 bar
Flow rate max. 25 l/min
Pressure setting range 10 to   70 bar
20 to 110 bar
20 to 250 bar
20 to 320 bar
Primary pressure dependence As primary pressure increases, the control pressure drops 8% ± 3% of the primary pressure change
Internal leakage Leakage-free,
approx. 100 cmᶟ at port 2
Media operating temperature range NBR: min. -30 °C to max. +100 °C
FKM: min. -20 °C to max. +120 °C
TT NBR: min. -40 °C to max.   +80 °C (low temperature)
Ambient temperature range NBR: min. -30 °C to max. +100 °C
FKM: min. -20 °C to max. +120 °C
TT NBR: min. -40 °C to max.   +80 °C (low temperature)
Operating fluid Hydraulic oil according to DIN 51524 Part 1, 2 and 3
Viscosity range min. 10 mm²/s to max. 420 mm²/s
Filtration < 210 bar: min. 20/18/15
(to ISO 4406) > 210 bar: min. 19/17/14
MTTFd 150 – 1200 years, measurement according to DIN EN ISO 13849-1
Installation No orientation restrictions
Materials Valve body: Steel
Piston: Hardened and ground steel
Seals: NBR
Back-up rings: PTFE
Cavity 10121 metric
Weight 0.48 kg
* see “Conditions and Instructions for Valves” in brochure 53.000

DIMENSIONS
The valve must be in a Adjustment type CC
relieved state when the
pressure setting is reduced
by adjustment.
HEX16
Torque 15 Nm

HEX30
Torque *
HEX30
Torque *

Adjustment type H

Torque
Max. 12 Nm

HEX30
Torque *
EN 5.169.13.0/07.20

*Torque:
Steel manifold (tensile strength > 360 N/mm²): 70 Nm
Aluminium manifold (tensile strength > 330 N/mm²): 50 Nm
(With torque tool in acc. with DIN EN ISO 6789, tool type II class A or B)
For more information see “Conditions and Instructions for Valves” Millimetre (inch)
in brochure 53.000 Subject to technical modifications

2
CAVITY
10121

Fit depth
Fit depth

VE = Visual examination
* Permitted drilling zone (for manifold design)
** Sharp edges should be avoided by rounding to
a radius of 0.1 mm to 0.2 mm
*** Largest pre-drilling diameter Millimetre (inch)
(nominal tool diameter) Subject to technical modifications

MODEL CODE
DMM10121 – 12 – C – N – 250  C  250
Basic model
2-way pressure reducing valve, metric
Type
12 = spring chamber relief to the tank (port 3)
Body and ports*
C = cartridge only
Sealing material
N = NBR (standard)
V = FKM
Pressure ranges
070 = 10 to 70 bar
110 = 20 to 110 bar
250 = 20 to 250 bar
320 = 20 to 320 bar
Adjustment type
C = adjustable using tool or sealable
CC = sealed with seal cap
EN 5.169.13.0/07.20

H = with handwheel and locking via knurled nut

Pressure setting
No details = no setting
250 = preset customer-specific pressure setting (specified in bar)

3
 TYPICAL PERFORMANCE
DMM10121-1.-C-.-320 DMM10121-1.-C-.-250
Measured at p1 = 400 bar, ν = 33 mm²/s, Toil = 46 °C Measured at p1 = 350 bar, ν = 33 mm²/s, Toil = 46 °C
Control pressure [bar]

Control pressure [bar]

Flow rate [l/min] Flow rate [l/min]

DMM10121-1.-C-.-110 DMM10121-1.-C-.-070
Measured at p1 = 200 bar, ν = 33 mm²/s, Toil = 46 °C Measured at p1 = 160 bar, ν = 33 mm²/s, Toil = 46 °C
Control pressure [bar]

Control pressure [bar]

Flow rate [l/min] Flow rate [l/min]

MATERIAL OVERVIEW
Standard models
Model code Part no.
DMM10121-12-C-N-070C 4255718
DMM10121-12-C-N-250C 4228641
DMM10121-12-C-N-320C 4278989
Other versions on request

Spare parts seal kits

Code Material Part no.
Seal kit DMM10121 TT-NBR (low temperature) 3676021
Other seal kits on request

Accessories, standard in-line bodies

Code Material Ports Pressure Part no.
H-R10121-SB4/2 Steel, zinc-plated G1/4“, G1/2“ 420 bar 395236
Other housings on request

Accessories, form tools for cavity

Tool Part no.
Countersink 163910
Reamer 163911

NOTE
The information in this brochure relates to the operating conditions and applications described.
For applications or operating conditions not described, please contact the relevant technical department.
Subject to technical modifications.
EN 5.169.13.0/07.20

HYDAC Fluidtechnik GmbH

Justus-von-Liebig-Str.
66280 Sulzbach/Saar, Germany
Tel: 0 68 97 /509-01
Fax: 0 68 97 /509-598
E-mail: [email protected]
4