4.
OPERATION
® 1) Magnetize the device to be measured.
TurboTester User Guide - Position the TurboTester® with the back facing upwards, allowing you to see the gray rectangular
region indicated as “Magnetize to test” (7).
Non-contact high speed tachometer for - With the device to be measured turned off, touch its side edge to the magnetic region (7) for
dental handpieces and frequency meter for approximately 5 seconds. This procedure will magnetize the ultrasonic handpiece rotor or the ultrasonic
ultrasonic dental equipment. tip for sensing by the magnetic sensor (0).
1. INTRODUCTION
We designed TurboTester® to provide long lifespan and outstanding performance on measuring the Before testing, the device to be measured must be magnetized.
rotational speed of dental handpieces and frequency of ultrasonic dental equipment operating
continuously or in bursts. This user guide holds indispensable information on the proper use and 2) Turning on the meter
maintenance of the equipment. Please read it carefully before starting up the measurements. Press the SET (1) button shortly. In the signal absence, the display will inform “00.00” or “000.0”.
3) Select the operating mode
WARNING! Improper use can lead to incorrect results
With the meter turned on, press the SET (1)
button shortly to select the operating mode.
2. IMPORTANT INFORMATION Indicator points (2&3) will alternate to indicate
Users of cardiac pacemaker should not put the TurboTester® meter in their shirt pocket. the current setting RPM(x1000) or kHz.
kRPM (RPM x 1000) kHz
WARNING! The TurboTester® has a neodymium magnet inside that 4) Performing a measurement
generates strong magnetic fields. Never place the meter near cardiac Position the TurboTester® with the display (4) upwards, turn on the device to be measured and bring its
pacemakers or similar devices. end to the sensor (0) keeping it at a distance of approximately 1 cm (3/8 in). The measured result will be
shown immediately on the display.
3. FEATURES
(0) High-frequency magnetic sensor;
(1) SET: On-off and selection button between
frequency (kHz) and rotational speed (kRPM);
(2&3) Decimal point and unit indication (kRPM or Before testing ultrasonic devices, make sure TurboTester® is in kHz mode.
For handpieces, make sure the TurboTester® is in RPM(x1000) mode.
kHz);
(4) Four digits LCD display;
(5) Case top part; If an ultrasonic device is mistakenly measured in RPM(x1000) mode,
(6) Fixing screws; the TurboTester® will show “Out”. If a handpiece is measured in kHz
(7) Magnet region; mode, the rotation will be erroneously displayed divided by 60.
(8) Serial number;
(9) Case bottom part. 5) Turning the meter off
Press and hold the SET (1) button until the meter turns off.
6) Auto-shutdown
The meter automatically turns off after 3 minutes in idle to save the battery.
To be continued →
5. REPLACING THE LITHIUM COIN 7. SPECIFICATIONS
Models: TT80k and TT50K.
Frequency range / resolution: 1-80 kHz / 10 Hz.
The meter operates with a lithium coin model CR 2032
Rotational speed range / resolution: 1.0-999.9 kRPM / 250 RPM.
(3V). Replace it when display shows the message "Lo b"
Measurement distance: 1 cm (3/8 in).
(see image). It means “Low battery” (voltage below 2.3
Measurable ultrasonic signals: Sinusoidal continuous or in bursts with duration 0.1 s.
Volts).
Temperature drift: 7 ppm/°C (12.6 ppm/°F).
Uncertainty at 25 °C (77 °F) for 95 % confidence level:
±480 RPM for rotational speed.
±8 Hz for continuous ultrasonic signals and bursts with duration ≥0.35 s.
Latency: 0.1 s. Lithium coin: CR 2032 (1-year on standby or
To replace the lithium coin: Refresh rate: Dynamic, 2 Hz typical. 1000 uses).
Size: 9.1 x 5.1 x 1.6 cm (0.36 x 0.20 x 0.06 in). Weight: <50 g (<1.6 oz) including battery.
1°) Remove the four screws (6) located on the case bottom Weight: <50 g (<1.6 oz) including battery. IP protection level: IP40.
part (9) using a small Phillips screwdriver and then remove
the case bottom as shown in the figure; Manufacturer: ATCP Physical Engineering.
Origin: Brazil.
HS code: 903089.
8. CALIBRATION
We recommend the calibration interval of 03 years with regards frequency and rotational speed
accuracy. To perform the calibration, a standard ferrite core 100 H inductor with a calibrated
2°) Carefully remove the electronics of the case and push frequency generator set on 10,000 kHz ±1 Hz can be used. The calibration with regards sensitivity is
the lithium coin out of the holder; not required.
3°) Insert the new lithium coin in the holder (pay attention
to the polarity indicated on the holder’s top);
4°) Replace the electronic circuit making sure to place it
exactly over the four holders;
5°) Attach the case bottom (9) and close the set. Insert and
tighten the screws (6) until fix the case firmly.
6. WARRANTY
The TurboTester® has 02 years warranty from the date of purchase against defects in material and
manufacturing. Factors that imply the loss of warranty:
- Failure to observe this user’s guide recommendations;
- Modifications in the meter or in its parts;
- Accidents, fall, improper operation or any other damage caused by misuse or action of natural Version 3.0
agents. Jun / 2021
