Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves

Characteristics Series R / RS (Parker), R*V (Denison)

Pilot operated pressure relief valves are available with

both Parker (series R/RS) and Denison (series R4V/R6V)
model codes.
A manually adjusted pilot stage controls a seated type
main stage.
A vent function with a solenoid operated directional valve
is available for circulation at minimum pressure.

Features
• Pilot operated with manual adjustment R25R RS25R
• 2 interfaces
- Subplate ISO 6264 (DIN 24340 Form D)
with VV01 vent valve
- Subplate ISO 6264 (DIN 24340 Form E)
with Cetop 03 vent valve
4
• 4 pressure stages
• 3 adjustment modes
- hand knob
- acorn nut with lead seal
- Key lock
• Remote control via port X RS25M

RS25R Function:
Series R
System pressure in port P is applied via the X gallery to
the spring loaded cone in the pilot head. The pilot head
controls the pressure in the Z area on top of the main
cartridge which is additionally kept close by the main
spring.
If the pilot pressure exceeds the setting pressure the pilot
cone opens and thus limits the pilot pressure.
When the system pressure exceeds the pilot pressure
plus the spring force, the main cartridge opens to port T
and limits the pressure in port P to the adjusted level.

Series RS
Z Additionally to the relief function of series R, a solenoid
operated vent valve connects the Z area to tank. This
X Y allows oil circulation from P to T at minimum pressure
drop. The vent valve can either be a standard Cetop 03
valves (mounting form E) or a sandwich unit (mounting
Y form D). For both types the vent position can be either at
the energized or de‑energized solenoid.
X P T

Code 1 Code 9

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-27 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
 Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Ordering Code Series R (Parker)

R S
Pressure Interface Adjust- Poppet Design
relief valve ment spring series
(not required
for ordering)

Nominal Pressure Pilot oil Seals

size stages

Code Nominal size Code Seals

4 10
25
NG10
NG25
N
V
NBR
FPM
32 NG32

Pilot oil
Code Interface Code Pilot Drain
1 Internal External
4 Internal Internal
M
Subplate
mounting
ISO 6264 Code Adjustment
R 1) Hand knob
S
(Standard)
L Key lock
1) drain line with pipe only Acorn nut with
A
lead seal

Code Pressure stages

07 up to 70 bar
17 up to 175 bar
25 up to 250 bar
35 up to 350 bar

The Parker model code should

be used for all new applications.
Otherwise also refer to Denison
model code.
R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-28 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Ordering Code Series R*V (Denison)

R V - 5 - -
Pressure Relief Max. Pressure Pilot oil Seals
valve function pressure setting range
(350 bar)

Interface Nominal Drain Adjust- Design Modifi-

size port ment series cations

Code Interface Code Seals

4
1
5
NBR
FPM
4
Subplate
mounting
ISO 6264 Code Design
6 A R4V
B R6V

Code Nominal size Pilot oil

03 NG10 Code Drain line
06 NG25 0 internal
10 NG32 1 1) external from subplate
external from valve
2 2)
body (Y-port)
1) R4V only
Code Interface Drain port 2) R6V only
Y port in
3 R4V
mounting pattern
Code Adjustment
9 R6V Y-port = G 1/8“
Hand knob 32mm dia.
1
(Standard)
Code Pressure stages 3 Acorn nut with lead seal
1 up to 105 bar 4 Key lock
3 up to 210 bar
5 up to 350 bar

The Denison model code is avail-

able for existing applications.
Otherwise also refer to Parker
model code.

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-29 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
 Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Ordering Code Series RS (Parker)

RS S W
Pressure Interface Adjustment Poppet Switching Without Design
relief valve spring type plug series
with elec. (not required
unloading for ordering)

Nominal Pressure Pilot oil Seals Solenoid Options

size stages voltage

Code Nominal size / Mounting Code Options

4 10
25
NG10
NG25
Subplate
mounting
omit
S
Standard
with slow unloading
32 NG32

Code Solenoid
Code Interface K 12V =
J 24V =
U 98V =
M
G 205V =
Subplate
110V / 50Hz
mounting Y
120V / 60Hz
ISO 6264
230V / 50Hz
R 1) T
240V / 60Hz

1) external drain with pipe only

Code Switching type
Solenoid not activ.
1 2)
Code Pressure stages unpress. circulation
07 up to 70 bar Solenoid activated
9 2)
17 up to 175 bar unpress. circulation
2) detailed symbols see characteristics.
25 up to 250 bar
35 up to 350 bar

Code Seals
N NBR
Code Adjustment
V FPM
Hand knob
S
(Standard)
L Key lock
Acorn nut with Pilot oil
A Code Pilot Drain
lead seal
1 Internal External
4 Internal Internal
Other solenoid voltages on request.

The Parker model code should

be used for all new applications.
Otherwise also refer to Denison
model code.

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-30 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Ordering Code R*V with Vent Function (Denison)

R V - 5 - - - - -
Pressure Relief Max. Pressure Pilot oil Solenoid Seals
valve function Pressure setting voltage
(350 bar) range

Interface Nominal Drain Adjust- Vent Design Modifi-

size port ment valve series cations
function

Code Interface Code Seals

4
1
5
NBR
FPM
4
Subplate
mounting
ISO 6264 Code Design
6 A R4V
B R6V

Code Nominal size Code Voltage

03 NG10 G0R 12V =
06 NG25 G0Q 24V =
10 NG32 GAR 98V =
GAG 205V =
110V / 50Hz
W30
Code Interface Drain port 120V / 60Hz
Y port in 230V / 50Hz
3 R4V W31
mounting pattern 240V / 60Hz
9 R6V Y-port = G 1/8“

Code Vent valve

Code Pressure stages Solenoid not activ.
09
unpress. circulation
1 up to 105 bar
Solenoid activated
3 up to 210 bar 11
unpress. circulation
5 up to 350 bar

Pilot oil
Code Adjustment
Code Drain line
1 Hand knob (Standard)
0 internal
3 Acorn nut with lead seal
1 1) external from subplate
4 Key lock
external from valve
2 2)
body (Y-port)
1) R4V only
2) R6V only

The Denison model code is avail-

able for existing applications.
Otherwise also refer to Parker
model code.

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-31 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
 Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Technical Data Series R / RS (Parker), R*V (Denison)

R / R*V

General
Nominal size 10 25 32
Interface Subplate mounting acc. ISO 6264
Mounting position as desired, horizontal mounting prefered
Ambient temperature [°C] -20...+80
Weight Series R*R / R6V [kg] 4.5 5.8 7.8
Series R*M / R4V [kg] 2.7 4.5 6.0
Hydraulic
Max. operating pressure [bar] Ports P (or A) and X up to 350, Port T (or B) and Y depressurized
Pressure stages [bar] 75, 175, 250, 350 (series R) : 105, 210, 350 (series R*V)
Nominal flow Series R*R / R6V [l/min] 250 500 650
Series R*M / R4V [l/min] 150 350 650

4 Fluid
Viscosity, recommended [cSt] / [mm²/s]
Hydraulic oil according to DIN 51524 ... 525
30 ... 50
permitted [cSt] / [mm²/s] 20 ... 380
Fluid temperature [°C] -20 ... +70
Filtration ISO 4406 - (1999) ; 18/16/13

RS / R*V with vent function

General
Nominal size 10 25 32
Interface Subplate mounting acc. ISO 6264
Mounting position as desired, horizontal mounting prefered
Ambient temperature [°C] -20...+80
Weight Series RS*R / R6V [kg] 5.9 7.2 9.2
Series RS*M / R4V [kg] 4.4 6.2 7.7
Hydraulic
Max. operating pressure [bar] Ports P (or A) and X 350, port T (or B) and Y depressurized
Pressure stages [bar] 75, 175, 250, 350 (series R) : 105, 210, 350 (series R*V)
Nominal flow Series RS*R / R6V [l/min] 250 500 650
Series RS*M / R4V [l/min] 150 350 650
Fluid Hydraulic oil according to DIN 51524 ... 525
Viscosity, recommended [cSt] / [mm²/s] 30 ... 50
permitted [cSt] / [mm²/s] 20 ... 380
Fluid temperature [°C] -20 ... +70
Filtration ISO 4406 - (1999) ; 18/16/13
Electrical
Duty ratio [%] 100 ED; CAUTION: coil temperature up to 180 °C possible
Max. switching frequency [1/h] 16000 (DC), 7200 (AC)
Protection class IP 65 in according with EN 60529 (plugged and mounted)
Code Denison / Code Parker G0R / K G0Q / J GAR / U GAG / G W30 / Y W31 / T
110V/50Hz 230V/50Hz
Supply voltage [V] 12V = 24V = 98V = 205V =
120V/60Hz 240V/60Hz
Tolerance supply voltage [%] +5...-10 +5...-10 +5...-10 +5...-10 +5...-10 +5...-10
Power consumption hold [W] 31 31 31 31 78 78
in rush [W] 31 31 31 31 264 264
Solenoid connection Connector as per EN 175301-803
Wiring min. [mm2] 3 x 1.5 recommended
Wiring length max. [m] 50 recommended

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-32 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Characteristic Curves Series R / RS (Parker), R*V (Denison)

p/Q performance curve

Series R/RS*M / R4V 1) Minimum pressure curve

p/Q performance curve

Series R/RS*R/R6V 1) Minimum pressure curve

1) The performance curves are measured with external drain.

For internal drain the tank pressure has to be added to curve.

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-33 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
 Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Dimensions Series R / RS (Parker), R*V (Denison)

R*R / R6V

L5 30 X1
L3 X3 X2
d4xt4
X5

Hand
knob

Y3
Ød2

Ød1
B1
P T

Y1
X

B2
4 L1 Key lock
X7
Ød3xt3

L2

Ød6
H1
H3
H2

Y: external drain port G 1/8“

H5

Y
H6

Ød5 L6

NG ISO-code x1 x2 x3 x4 x5 x6 x7 y1 y2 y3 y4 y5 y6
10 6264-06-09-*-97 53.8 47.5 0 – 22.1 – 22.1 53.8 – 26.9 – – –
25 6264-08-13-*-97 66.7 55.6 23.8 – 11.1 – 33.4 70 – 35 – – –
32 6264-10-17-*-97 88.9 76.2 31.8 – 12.7 – 44.5 82.6 – 41.3 – – –
Tolerance at X and Y pin holes and screw holes ±0.1, at port holes ±0.2.

NG ISO-code B1 B2 H1 H2 H3 H4 H5 H6 L1 L2 L3 L4 L5 L6
10 6264-06-09-*-97 80 26.9 114 27 88 20.5 25 52.5 118.5 141 180 29.5
25 6264-08-13-*-97 100 35 117.5 45.5 91.5 – 25 12 37.9 124.5 141 – 180 36.5
32 6264-10-17-*-97 120 41.3 123 52 97 26.5 13.5 45 153 141 180 46.5

NG ISO-code d1max d2max d3 t3 d4 t4 d5 d6

10 6264-06-09-*-97 14.7 4.8 7.5 10 M12 20 13.5 20
25 6264-08-13-*-97 23.4 6.3 7.5 10 M16 27 17.5 25
32 6264-10-17-*-97 32 6.3 7.5 10 M18 28 20 30

NG ISO-code Bolt kit Surface finish

NBR FPM
10 6264-06-09-*-97 BK 494 4xM12 x 45 DIN 912 12.9 108 Nm ±15% SK-R10RN40 SK-R10RV40
25 6264-08-13-*-97 BK 366 4xM16 x 70 DIN 912 12.9 264 Nm ±15% SK-R25RN40 SK-R25RV40
32 6264-10-17-*-97 BK 507 4xM18 x 75 DIN 912 12.9 398 Nm ±15% SK-R32RN40 SK-R32RV40

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-34 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Dimensions Series R / RS (Parker), R*V (Denison)

RS*R / R6V with vent function X1

L3 X3 X2
X5 d4xt4

Y3
Ød1
Ød2
B1

Y1
X P T

B2
Ød3xt3
L1 X7
L2

15

Hand knob
H1
H4

Ød6 Key lock Y: external drain port G 1/8“

H3
H2

H5

Y
H6

Ød5 L6
L5 30

NG ISO-code x1 x2 x3 x4 x5 x6 x7 y1 y2 y3 y4 y5 y6
10 6264-06-09-*-97 53.8 47.5 0 – 22.1 – 22.1 53.8 – 26.9 – – –
25 6264-08-13-*-97 66.7 55.6 23.8 – 11.1 – 33.4 70 – 35 – – –
32 6264-10-17-*-97 88.9 76.2 31.8 – 12.7 – 44.5 82.6 – 41.3 – – –
Tolerance at X and Y pin holes and screw holes ±0.1, at port holes ±0.2.

NG ISO-code B1 B2 H1 H2 H3 H4 H5 H6 L1 L2 L3 L4 L5 L6
10 6264-06-09-*-97 80 26.9 206 27 88 136.5 25 12 52.5 118.5 163.8 180 36.5
25 6264-08-13-*-97 100 35 210 45.5 91.5 140 25 12 37.9 124.5 163.8 – 180 36.5
32 6264-10-17-*-97 120 41.3 215.5 52 97 145.5 25 12 45 153 163.8 180 36.5

NG ISO-code d1max d2max d3 t3 d4 t4 d5 d6

10 6264-06-09-*-97 14.7 4.8 7.5 10 M12 20 13.5 20
25 6264-08-13-*-97 23.4 6.3 7.5 10 M16 27 17.5 25
32 6264-10-17-*-97 32 6.3 7.5 10 M18 28 20 30

NG ISO-code Bolt kit Surface finish

NBR FPM
10 6264-06-09-*-97 BK 494 4xM12 x 45 DIN 912 12.9 108 Nm ±15% SK-RS10RN40 SK-RS10RV40
25 6264-08-13-*-97 BK 366 4xM16 x 70 DIN 912 12.9 264 Nm ±15% SK-RS25RN40 SK-RS25RV40
32 6264-10-17-*-97 BK 507 4xM18 x 75 DIN 912 12.9 398 Nm ±15% SK-RS32RN40 SK-RS32RV40

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-35 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
 Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Dimensions Series R / RS (Parker), R*V (Denison)

R*M / R4V X1
X2
X3
X4 d4xt4
X5 Ød2

Y4
Y

Y5

Ød3xt3

Y3
Ød1

Y2
B1

Y1
A B

B2
Key lock
X

4 L1
X6
Ød2

L2
L5 30

L6
L4 Hand knob

Acorn nut
Ød6 with lead seal
H1
H5

Ød5
H2

NG ISO-code x1 x2 x3 x4 x5 x6 x7 y1 y2 y3 y4 y5 y6
10 6264-06-07-*-97 42.9 35.8 21.5 – 7.2 21.5 0 66.7 58.8 33.4 7.9 14.3 –
25 6264-08-11-*-97 60.3 49.2 39.7 – 11.1 20.6 0 79.4 73 39.7 6.4 15.9 –
32 6264-10-15-*-97 84.2 67.5 59.5 42.1 16.7 24.6 0 96.8 92.8 48.4 3.8 21.4 –
Tolerance at X and Y pin holes and screw holes ±0.1, at port holes ±0.2.

NG ISO-code B1 B2 H1 H2 H3 H4 H5 H6 L1 L2 L3 L4 L5 L6
10 6264-06-07-*-97 87.3 33.35 83 21 – – 62.5 – 29 94.8 – 143 181 144.8
25 6264-08-11-*-97 105 39.7 109.5 29 – – 89 – 34.7 126.8 – 143 181 144.8
32 6264-10-15-*-97 120 48.4 120 29 – – 99.5 – 30.6 144.3 – 143 181 144.8

NG ISO-code d1max d2max d3 t3 d4 t4 d5 d6

10 6264-06-07-*-97 15 7 7.1 8 M10 16 10.8 17
25 6264-08-11-*-97 23.4 7.1 7.1 8 M10 18 10.8 17
32 6264-10-15-*-97 32 7.1 7.1 8 M10 20 10.8 17

NG ISO-code Bolt kit Surface finish

NBR FPM
10 6264-06-07-*-97 BK 505 4x M10 x 35 DIN 912 12.9 63 Nm ±15% SK-R10MN40 SK-R10MV40
25 6264-08-11-*-97 BK 485 4x M10 x 45 DIN 912 12.9 63 Nm ±15% SK-R25MN40 SK-R25MV40
32 6264-10-15-*-97 BK 506 6x M10 x 45 DIN 912 12.9 63 Nm ±15% SK-R32MN40 SK-R32MV40

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-36 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
Catalogue HY11-3500/UK Pilot Operated Pressure Relief Valves
Dimensions Series R / RS (Parker), R*V (Denison)

RS*M / R4V with vent function

L5 30 X1
X2
L2 X3
X4 d4xt4
L1 Ød2
X5

Ød3xt3

Y4
Y

Y5

Y3
B1

Ød1

Y2
Y1
A B

B2
Key lock

B3
X

Ød2

15
X6

L6
L7
L4
Acorn nut
with lead seal

Hand knob
H1
H4

Ød6
H3

Ød5
H2

NG ISO-code x1 x2 x3 x4 x5 x6 x7 y1 y2 y3 y4 y5 y6
10 6264-0-07-*-97 42.9 35.8 21.5 – 7.2 21.5 0 66.7 58.8 33.4 7.9 14.3 –
25 6264-08-11-*-97 60.3 49.2 39.7 – 11.1 20.6 0 79.4 73 39.7 6.4 15.9 –
32 6264-10-15-*-97 84.2 67.5 59.5 42.1 16.7 24.6 0 96.8 92.8 48.4 3.8 21.4 –
Tolerance at X and Y pin holes and screw holes ±0.1, at port holes ±0.2.

NG ISO-code B1 B2 B3 H1 H2 H3 H4 H6 L1 L2 L3 L4 L5 L6 L7
10 6264-06-07-*-97 87.3 33.35 70 130 21 68.5 109.5 – 29 94.8 – 143 181 165.6 144.8
25 6264-08-11-*-97 105 39.7 70 156.5 29 95 136 – 34.7 126.8 – 143 181 165.6 144.8
32 6264-10-15-*-97 120 48.4 70 167 29 105.5 146.5 – 30.6 144.3 – 143 181 165.6 144.8

NG ISO-code d1max d2max d3 t3 d4 t4 d5 d6

10 6264-06-07-*-97 15 7 7.1 8 M10 16 10.8 17
25 6264-08-11-*-97 23.4 7.1 7.1 8 M10 18 10.8 17
32 6264-10-15-*-97 32 7.1 7.1 8 M10 20 10.8 17

NG ISO-code Bolt kit Surface finish

NBR FPM
10 6264-06-07-*-97 BK 505 4x M10 x 35 DIN 912 12.9 63 Nm ±15% SK-RS10MN40 SK-RS10MV40
25 6264-08-11-*-97 BK 485 4x M10 x 45 DIN 912 12.9 63 Nm ±15% SK-RS25MN40 SK-RS25MV40
32 6264-10-15-*-97 BK 506 6x M10 x 45 DIN 912 12.9 63 Nm ±15% SK-RS32MN40 SK-RS32MV40

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-37 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany
 Catalogue HY11-3500/UK
Notes

R-RS-R4V-R6V_UK.INDD CM_29.01.2008.1

4-38 Parker Hannifin GmbH & Co. KG

Hydraulic Controls Division
Kaarst, Germany