Product Specification M185XW01 V0

AU OPTRONICS CORPORATION

(V ) Preliminary Specification
( ) Final Specification

Module 18.5” Color TFT-LCD

Model Name M185XW01 V0

Customer Date Approved by Date

Approved by Prepared by

Chiyinwu 2008/06/13

Note: This Specification is subject to Desktop Display Business Group /

change without notice. AU Optronics corporation

[Link]
document version 0.3 1
 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

Contents

1.0 Handling Precautions .........................................................................................5

2.0 General Description............................................................................................6
2.1 Display Characteristics.......................................................................................................6
2.2 Optical Characteristics .......................................................................................................7
3.0 Functional Block Diagram................................................................................11
4.0 Absolute Maximum Ratings.............................................................................12
4.1 TFT LCD Module ..............................................................................................................12
4.2 Backlight Unit ...................................................................................................................12
4.3 Absolute Ratings of Environment .....................................................................................12
5.0 Electrical characteristics..................................................................................13
5.1 TFT LCD Module ..............................................................................................................13
5.1.1 Power Specification....................................................................................................13
5.1.2 Signal Electrical Characteristics.................................................................................14
5.2 Backlight Unit ...................................................................................................................15
6.0 Signal Characteristic ........................................................................................17
6.1 Pixel Format Image ..........................................................................................................17
6.2 The input data format .......................................................................................................18
6.3 Signal Description ............................................................................................................19
6.4 Timing Characteristics......................................................................................................21
6.5 Timing diagram.................................................................................................................22
6.6 Power ON/OFF Sequence................................................................................................23
7.0 Connector & Pin Assignment ..........................................................................24
7.1 TFT LCD Module ..............................................................................................................24
7.1.1 Pin Assignment ..........................................................................................................24
7.2 Backlight Unit ...................................................................................................................25
7.2.1 Signal for Lamp connector .........................................................................................25
8.0 Reliability Test...................................................................................................26
9.0 Shipping Label ..................................................................................................27
10.0 Mechanical Characteristics............................................................................28

document version 0.3 2

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

Record of Revision

Version and Pag

Old description New Description Remark
Date e
0.1 All First Edition for Customer N/A
2008/03/10
0.2 All old format new format
2008/06/02
5 2.1 Display Characteristics 2.1 Display Characteristics
1. No screen diagnoal description 1. add screen diagnoal : 470.1 mm (18.51”)
2. weight 1900(max) TDB 2. weight 2000 (max)
3. No temperature range 3. add temperature range
o
甲、 operating 0~+50 [ C]
o
乙、 storage (shipping) -20 to +60 [ C]
6 View angel

10 1. I/F PCB interface 1. I/F PCB Interface:

FI-XB30SSRL-HF16(JAE)/MSCKT2407P30HB(
FI-XB30SSRL-HF16 (JAE) / MSCKT2407P30B
信盛)
(信盛)

2. Lamp connector 2. Lamp connector

CVILUX CP0502SL090 / YEON HO Deleted

35001HS-02L

Mating Type: 35001WR-02LP

14 5.1.2 Signal Electrical

Characteristics

15 5.2 BL unit (1)

(1)

(2) Note 8: The CCFL can work normally if the

PWM Dimming ratio range is from 20% to 100%
and the lamp current is 7.5mA

(2) Deleted Notes 8

document version 0.3 3

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

21 6.4.1 Timing Characteristics

24 7.1 TFT LCD Module

25 7.2 Backlight Unit

Connector Name / Designation Lamp Connector / Backlight lamp
Manufacturer YEON HO
Connector Name / Designation Lamp Connector / Backlight lamp Type Part Number 35001HS-02L
Manufacturer CVILUX or YEON HO
Mating Type Part Number 35001W R-02LP
Type Part Number CP0502SL090/35001HS-02L

Mating Type Part Number CP0502P1ML0/35001WR-02LP

27 9.0 Shipping Label

28,2 2D drawing –PCBA 2D drawing –change PCBA size

9
Signal Item Symbol Min Typ Max Unit
0.3 21 6.4.1 Timing Characteristics Period Th 1416 1606 2047 Tclk
Active Tdisp(h) 1366 1366 1366 Tclk

2008/6/13 H-section Blanking

Note2 : Clock Frequency 90MHz(Max.)= 1416(H)*847(V)*75Hz
Tblk(h) 50 240 681 Tclk

document version 0.3 4

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the CCFL reflector edge. Instead, press at
the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.

document version 0.3 5

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

2.0 General Description

This specification applies to the 18.5 inch-wide Color a-Si TFT-LCD Module [Link]
display supports the WXGA - 1366(H) x 768(V) screen format and 16.7M colors (RGB 6-bits +
Hi-FRC data). All input signals are 1-channel LVDS interface and this module doesn ’t contain an
inverter board for backlight.

2.1 Display Characteristics

The following items are characteristics summary on the table under 25℃ condition:

ITEMS Unit SPECIFICATIONS

Screen Diagonal [mm] 470.1(18.51”)
Active Area [mm] 409.8 (H) x 230.4 (V)
Pixels H x V 1366(x3) x 768
Pixel Pitch [um] 300 (per one triad) × 300
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
[cd/m2]
2
White Luminance ( Center ) 300 cd/m (@ 7.5mA (Typ.)
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)

Nominal Input Voltage VDD [Volt] +5.0 V (Typ)

Power Consumption [Watt] 17 W (Typ.)
(VDD line + CCFL line) (without inverter, all black pattern)
Weight [Grams] 2000 (Max)
Physical Size [mm] 430.37 (W) x 254.6 (H) Typ. x 16.5 (D) Max
Electrical Interface One channel LVDS
Support Color 16.7M colors (RGB 6-bit + Hi_FRC )
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating [oC] 0 to +50
Storage (Shipping) [oC] -20 to +60
RoHS Compliance RoHS Compliance

document version 0.3 6

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25 ℃:

Item Unit Conditions Min. Typ. Max. Note

Horizontal (Right) -
150 170 -
CR = 10 (Left)
Viewing Angle [degree] 2
Vertical (Up) -
140 160 -
CR = 10 (Down)

Contrast ratio Normal Direction 600 1000 - 3

Raising Time (TrR) - 3.6 5.7

Response Time [msec] Falling Time (TrF) - 1.4 2.3 4
Raising + Falling - 5 8
Red x 0.618 0.648 0.678
Red y 0.309 0.339 0.369
Color / Chromaticity Green x 0.262 0.292 0.322
Coordinates (CIE) Green y 0.573 0.603 0.633
5
Blue x 0.113 0.143 0.173
Blue y 0.040 0.070 0.100
White x 0.283 0.313 0.343
Color Coordinates (CIE) White White y 0.299 0.329 0.359
2
Central Luminance [cd/m ] 240 300 - 6
Luminance Uniformity [%] 75 80 - 7
Crosstalk (in 60Hz) [%] 1.5 8
Flicker dB -20 9

document version 0.3 7

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

Note 1: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35 ℃) . In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room.

Photo detector

Measured distance

LCD Panel TFT-LCD

Center of the screen

Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)

Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180 ° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the
screen rotated about its center to develop the desired measurement viewing angle.

document version 0.3 8

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

Note 3: Contrast ratio is measured by TOPCON SR-3

Note 4: Definition of Response time measured by Westar TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full
Black” to “Full White” (rising time, Tr R), and from “Full White” to “Full Black” (falling time, Tf F),
respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of
amplitudes.
% Tr F Tr R

100
90
Optical
W hite Black Black W hite
response
10
0
1 Frame 1 Frame

TrR + TfF = 5 msec (typ.).

Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3
Note 6: Central luminance is measured by TOPCON SR-3
Note 7: Luminance uniformity of these 9 points is defined as below and measured by
TOPCON SR-3

Minimum Luminance in 9 points (1 - 9)

Uniformity =
Maximum Luminance in 9 Points (1 - 9)
Note 8: Crosstalk is defined as below and measured by TOPCON SR-3

document version 0.3 9

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

CT = | YB – YA | / YA × 100 (%)

Where

YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3

RGBRGB
Gray Level = L127

RGBRGB

Gray Level = L0
RGBRGB

Method: Record dBV & DC value with TRD-100

Amplitude
AC

DC

Time
AC Level(at 30 Hz)
Flicker (dB) = 20 log
DC Level

document version 0.3 10

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

3.0 Functional Block Diagram

The following diagram shows the functional block of the 18.5 inch Color TFT-LCD Module:

AUO G1
ASIC

Y-Driver IC
Timing TFT-LCD
LVDS Controller
LVD Receiver 1366(x3) x 768
Pixels
Connector

RSDS
Transmitter

+5V X-Driver IC
G768
D1 D4098

2 CCFL

Gamma
DC/DC
Correction
Converter

I/F + X-PCB
DC
Inverter

I/F PCB Interface:

FI-XB30SSRL-HF16(JAE)/MSCKT2407P30HB(信盛)
Mating Type:
FI-X30HL (JAE)(Locked Type)

document version 0.3 11

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

4.0 Absolute Maximum Ratings

Absolute maximum ratings of the module are as following:
4.1 TFT LCD Module

Item Symbol Min Max Unit Conditions

Logic/LCD Drive
VDD 4.5 +5.5 [Volt] Note 1,2
Voltage

4.2 Backlight Unit

Item Symbol Min Max Unit Conditions

CCFL Current ICFL 3.0 8 [mA] rms Note 1,2

4.3 Absolute Ratings of Environment

Item Symbol Min. Max. Unit Conditions

Operating Temperature TOP 0 +50 [oC]
Operation Humidity HOP 5 90 [%RH]
Note 3
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST 5 90 [%RH]

Note 1: With in Ta (25℃)

Note 2: Permanent damage to the device may occur if exceeding maximum values
Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard).

Operating Range Storage Range

document version 0.3 12
 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

5.0 Electrical characteristics

5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as following:

Symbol Parameter Min Typ Max Unit Conditions

Logic/LCD Drive
VDD 4.5 5.0 5.5 [Volt] +/-10%
Voltage

VDD= 5.0V, All Black Pattern

IDD Input Current - 1.2 1.5 [A]
At 60Hz,

VDD= 5.0V, All Black Pattern

PDD VDD Power - 6 8.25 [Watt]
At 60Hz

IRush Inrush Current - - 3 [A] Note 1

Allowable Logic/LCD VDD= 5.0V, All Black Pattern

VDDrp - - 200 [mV] p-p
Drive Ripple Voltage At 60Hz

Note 1: Measurement conditions:

The duration of rising time of power input is 470us.
+5.0V Q3
AO6402
D6 F1
D5
D2 S
VCC
D1

R1 (LCD Module Input)

G

47K
C1
1uF/16V
(High to Low)
D1
D2
D5
D6

Control
Signal R2
Q3
AO6402
G

1K
S

C3
2

+12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1

47K

C2
1uF/25V

document version 0.3 13

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

5.1.2 Signal Electrical Characteristics

Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of
SN75LVDS82DGG (Texas Instruments) in detail.

Characteristics of each signal are as following:

Symbol Parameter Min Typ Max Units Condition

Differential Input High VICM = 1.2V
VTH - +50 +100 [mV]
Threshold Note 1
Differential Input Low VICM = 1.2V
VTL -100 -50 - [mV]
Threshold Note 1
│VID│ Input Differential Voltage 100 400 600 [mV] Note 1
Differential Input Common VTH-VTL = 200MV (max)
VICM +1.0 +1.2 +1.4 [V]
Mode Voltage Note 1

Note 1: LVDS Signal Waveform

VTH
│VID│
VTL

VICM

VSS

document version 0.3 14

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

5.2 Backlight Unit

Parameter guideline for CCFL Inverter is under stable conditions at 25 ℃ (Room Temperature):

Parameter Min. Typ. Max. Unit Note

CCFL Standard Current (ISCFL) 7.0 7.5 8.0 [mA] rms

CCFL Operation Current (IRCFL) 3.0 7.5 8.0 [mA] rms 2

CCFL Frequency (FCFL) 40 50 80 [KHz] 3, 4

CCFL Ignition Voltage (ViCFL, Ta= 0℃) 1650 - - [Volt] rms

5
CCFL Ignition Voltage (ViCF, Ta= 25℃) 1250 - - [Volt] rms
700
CCFL Operation Voltage (VCFL) - 880 [Volt] rms
(@7.5mA)
6
CCFL Power Consumption (PCFL) - 11 12.1 [Watt]

CCFL Life Time (LTCFL) 40,000 50,000 - [Hour] 7

Note 1: Typ. values are AUO recommended design values.

*1 All of characteristics listed are measured under the condition using the AUO test inverter.
*2 It is recommended to check the inverter carefully. Sometimes, interfering noise stripes appear
on the screen, and substandard luminance or flicker at low power may happen.
*3 While designing an inverter, it is suggested to check safety circuit very carefully. Impedance of
CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged.
*4 Generally, CCFL has certain delay time after applying kick-off voltage. It is recommended to
keep on applying kick-off voltage for 1 [Sec] until discharge.
*5 Reducing CCFL current will increase CCFL discharge voltage and generally increases CCFL
discharge frequency. So all the parameters of the inverter should be carefully designed so the
inverter will not produce too much leakage current from high-voltage output.
*6 For designing CCFL current, it is highly recommanded to use symmetric and consistent
sinusoidal wave for each CCFL input current with asymmetric ration of 10% or less in both
postive area and negative area (ie. 0.9*√2*Irms < I1 & I2 < 1.1*√2*Irms) as refer to the following
diagram, otherwise proper CCFL functionality cannot be guarantied.

document version 0.3 15

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

Note 2: CCFL standard current is measured by continue mode inverter at 25 ±2℃.

Note 3: CCFL discharge frequency should be carefully determined to avoid interference between
inverter and TFT LCD.
Note 4: The frequency range will not affect lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to release power that has generating capacity exceeding
1650 volt. Lamp units need minimum voltage, 1650 Volt, for ignition.
Note 6: The variance of CCFL power consumption is ±10%. (IRCFL × VCFL × 2 = PCFL)
Note 7: Definition of life time: brightness becomes 50%. The minimum life time of CCFL unit is on
the condition of 7.5mA CCFL current and 25 ±2℃.

document version 0.3 16

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

6.0 Signal Characteristic

6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.

1 2 1365 1366

1st Line R G B R G B R GB R G B

768 Line R G B R G B R GB R G B

document version 0.3 17

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

6.2 The input data format

LVDS Data Mapping of NS Format

LVDS Data Mapping of JEIDA Format

Note1: Normally, DE, VS, HS on EVEN channel are not used.

Note2: 8-bits signal input.

document version 0.3 18

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

6.3 Signal Description

The module using one LVDS receiver SN75LVDS82(Texas Instruments). LVDS is a
differential signal technology for LCD interface and high speed data transfer device. LVDS
transmitters shall be SN75LVDS83(negative edge sampling). The first LVDS port(RxOxxx)
transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.
PIN # SIGNAL NAME DESCRIPTION
1 NC No contact (For AUO internal use)
2 NC No contact (For AUO internal use)
3 NC No contact (For AUO internal use)
4 GND Power Ground
5 RXIN0- Negative LVDS differential data input (0)
6 RXIN0+ Positive LVDS differential data input (0)
7 GND Power Ground
8 RXIN1- Negative LVDS differential data input (1)
9 RXIN1+ Positive LVDS differential data input (1)
10 GND Power Ground
11 RXIN2- Negative LVDS differential data input (2)
12 RXIN2+ Positive LVDS differential data input (2)
13 GND Power Ground
14 RXCLKIN- Negative LVDS differential clock input (clock)
15 RXCLKIN+ Positive LVDS differential data input (clock)
16 GND Power Ground
17 RXIN3- Negative LVDS differential data input (3)
18 RXIN3+ Positive LVDS differential data input (3)
19 GND Power Ground
20 NC No contact (For AUO internal use)
21 NC No contact (For AUO internal use)
22 NC No contact (For AUO internal use)
23 GND Power Ground
24 GND Power Ground
25 GND Power Ground
26 VCC +5V power supply
27 VCC +5V power supply
28 VCC +5V power supply
29 VCC +5V power supply
30 VCC +5V power supply
Note1: Start from left side
document version 0.3 19
 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

1 30
VCC
-
NC

Note2: Input signals of clock shall be the same timing.

Note3: Please follow TV VESA Pin Assignment.

document version 0.3 20

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

6.4 Timing Characteristics

Basically, interface timing described here is not actual input timing of LCD module but close to
output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.

Signal Item Symbol Min Typ Max Unit

Period Tv 776 808 1023 Th
Active Tdisp(v) 768 768 768 Th
V-section Blanking Tblk(v) 8 40 255 Th
Period Th 1416 1606 2047 Tclk
Active Tdisp(h) 1366 1366 1366 Tclk
H-section Blanking Tblk(h) 50 240 681 Tclk
Period Tclk - 12.8 - ns
Clock Frequency Freq - 78 90 MHz
Frame Rate Frame Rate F 50 60 75 Hz

Note1 : DE mode only

Note2 : Clock Frequency 90MHz(Max.)= 1416(H)*847(V)*75Hz

document version 0.3 21

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

6.5 Timing diagram

document version 0.3 22

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

6.6 Power ON/OFF Sequence

VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the
chart. Signals from any system shall be Hi-Z state or low level when VDD is off.

Value
Parameter Unit
Min. Typ. Max.
T1 0.5 - 10 [msec]
T2 0 40 50 [msec]
T3 200 - - [msec]
T4 200 - - [msec]
T5 0.5 16 50 [msec]
T6 - - 100 [msec]
T7 1000 - - [msec]

document version 0.3 23

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

7.0 Connector & Pin Assignment

Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.

7.1 TFT LCD Module

Connector Name / Designation Interface Connector / Interface card

Manufacturer JAE or STM

Type Part Number FI-XB30SSRL-HF16(JAE)/MSCKT2407P30HB(STM)

FI-X30HL(JAE) (Locked Type)
Mating Housing Part Number
FI-X30H (JAE)(Unlocked Type)

7.1.1 Pin Assignment

Pin# Signal Name Pin# Signal Name

1 NC 2 NC
3 NC 4 GND
5 RXIN0- 6 RXIN0+
7 GND 8 RXIN1-
9 RXIN1+ 10 GND
11 RXIN2- 12 RXIN2+
13 GND 14 RXCLKIN-
15 RXCLKIN+ 16 GND
17 RXIN3- 18 RXIN3+
19 GND 20 NC
21 NC 22 NC
23 GND 24 GND
25 GND 26 VCC
27 VCC 28 VCC
29 VCC 30 VCC

document version 0.3 24

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

7.2 Backlight Unit

Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.

Connector Name / Designation Lamp Connector / Backlight lamp

Manufacturer YEON HO

Type Part Number 35001HS-02L

Mating Type Part Number 35001WR-02LP

7.2.1 Signal for Lamp connector

Connector No. Pin No. Input Color Function

1 Hot1 Pink High Voltage (Lamp1)
Upper CN1
2 Cold1 White Low Voltage(Lamp1)

Connector No. Pin No. Input Color Function

1 Hot1 Pink High Voltage(Lamp2)
Lower CN2
2 Cold1 White Low Voltage (Lamp2)

document version 0.3 25

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

8.0 Reliability Test

Environment test conditions are listed as following table.

Items Required Condition Note

Temperature Humidity Bias (THB) Ta= 50℃, 80%RH, 300hours

High Temperature Operation (HTO) Ta= 50℃, 50%RH, 300hours

Low Temperature Operation (LTO) Ta= 0℃, 300hours

High Temperature Storage (HTS) Ta= 60℃, 300hours
Low Temperature Storage (LTS) Ta= -20℃, 300hours
Acceleration: 1.5 Grms
Vibration Test Wave: Random
(Non-operation) Frequency: 10 - 200 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)

Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Drop Test Height: 60 cm, package test
Thermal Shock Test (TST) -20℃/30min, 60℃/30min, 100 cycles 1
On/Off Test On/10sec, Off/10sec, 30,000 cycles
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
8 points, 25 times/ point.
ESD (Electro Static Discharge) 2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
8 points, 25 times/ point.

Operation:10,000 ft
Altitude Test
Non-Operation:30,000 ft

Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20℃ to 60℃, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed
No data lost
Self-recoverable
No hardware failures.

document version 0.3 26

 Product Specification M185XW01 V0
AU OPTRONICS CORPORATION

9.0 Shipping Label

The label is on the panel as shown below:

Note 1: For Pb Free products, AUO will add for identification.

Note 2: For RoHS compatible products, AUO will add for identification.

Note 3: For China RoHS compatible products, AUO will add for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by
AUO Internal Green Team.

document version 0.3 27

10.0 Mechanical Characteristics

Ver 0.1
Ver 0.1