KATHREIN SE • P.O.

Box 10 04 44 • 83004 Rosenheim • Germany

KATHREIN SE
Anton-Kathrein-Straße 1–3
83022 Rosenheim
Rosenheim, 01.05.2018
Germany
Phone: +49 8031 184-0
Fax: +49 8031 184-306
KATHREIN-Werke KG ist jetzt KATHREIN SE www.kathrein.com
KATHREIN-Werke KG is now KATHREIN SE

Executive Board:
Zum 1. Mai 2018 ist die KATHREIN-Werke KG auf die KATHREIN SE, Anton Kathrein (CEO),
einer Europäischen Aktiengesellschaft (Societas Europaea), Joachim Döring, Elmar Geißinger,
übergegangen. Jürgen Walter, Hans-Joachim Ziems
Supervisory Board:
Die neuen Firmendaten lauten seither wie folgt: Dr. Michael F. Keppel (Chairman)
KATHREIN SE
Anton-Kathrein-Str. 1–3
83022 Rosenheim, Deutschland VAT Reg. No.: DE 131 558 540
Steuer-Nr.: 156/117/30745 Tax ID No.: 156/117/30745
UST-Ident-Nr.: DE 131 558 540 WEEE Reg. No.: DE 38438502
GLN: 40 21121 00000 3
Registergericht: Traunstein, HRB 24848
Registered Office: Rosenheim, DE
Commercial Register: Traunstein, HRB 24848

______________________________________________________________________________
Deutsche Bank AG
IBAN: DE54 7007 0010 0833 7701 00
BIC: DEUTDEMMXXX
On 1st May 2018, KATHREIN-Werke KG has been transferred
to KATHREIN SE, a European stock corporation (Societas Europaea).

Since then the company data is as follows:

KATHREIN SE
Anton-Kathrein-Str. 1–3
83022 Rosenheim, Deutschland
Tax ID No.: 156/117/30745
VAT Reg. No.: DE 131 558 540
Commercial Register: Traunstein, HRB 24848
936.0000218a

Page 1 of 1
 4-Port Antenna R1 Y1
Frequency Range 790–960 1710–2690
Dual Polarization X X
HPBW 65° 65°
Adjust. Electr. DT 0°–16° 2°–10°
set by hand or by optional RCU (Remote Control Unit)

4-Port Antenna 790–960/1710–2690 65°/65° 15/17.5dBi 0°–16°/2°–10°T

Type No. 80010664
Lowband R1, connector 1– 2
790 – 960
Frequency range MHz 790 – 862 824 – 894 880 – 960
Polarization ° +45, –45 +45, –45 +45, –45
Average gain dBi 14.5 ... 14.4 ... 14.2 14.6 ... 14.5 ... 14.3 14.8 ... 14.6 ... 14.4
Tilt ° 0 ... 8 ... 16 0 ... 8 ... 16 0 ... 8 ... 16
Horizontal Pattern:
Half-power beam width ° 69 68 67°
Front-to-back ratio, copolar (180°±30°) dB > 25 > 25 > 25
Cross polar ratio
Maindirection 0° dB Typically: 25 Typically: 25 Typically: 25
Sector ±60° > 10 >9 >8
Horizontal Pattern:
Half-power beam width ° 16.5 16.0 15.5
Electrical tilt ° 0–16, continuously adjustable
Sidelobe suppression for first sidelobe °T 0 ... 8 ... 16 0 ... 8 ... 16 0 ... 8 ... 16
above main beam dB 16 ... 15 ... 15 16 ... 15 ... 15 15 ... 15 ... 14
Impedance Ω 50
VSWR < 1.5
Isolation: Intrasystem dB > 30
Isolation: Intersystem dB > 30 (698–960 // 1710–2690 MHz)
Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier)
Max. effective power per port 300 (at 50 °C ambient temperature)
W
Max. effective power for the antenna 600 (at 50 °C ambient temperature)
Subject to alteration.
936.4850/b

www.kathrein.com 80010664 Page 1 of 3

KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
4-Port Antenna

Highband Y1, connector 3 – 4

1710 – 2690
Frequency range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690
Polarization ° +45, –45 +45, –45 +45, –45 +45, –45 +45, –45
Average gain dBi 17.2 ... 17.3 ... 16.8 17.4 ... 17.4 ... 16.9 17.6 ... 17.7 ... 17.0 17.0 ... 16.8 ... 16.0 17.2 ... 17.3 ... 16.7
Tilt ° 2 ... 6 ... 10 2 ... 6 ... 10 2 ... 6 ... 10 2 ... 6 ... 10 2 ... 6 ... 10
Horizontal Pattern:
Half-power beam width ° 63 64 66 73 65
Front-to-back ratio, copolar (180°±30°) dB > 25 > 28 > 29 > 26 > 25
Cross polar ratio dB
Maindirection 0° Typically: 18 > 20 20 23 23
Sector ±60° >9 > 10 > 10 > 10 >8
Horizontal Pattern:
Half-power beam width ° 6.2 5.8 5.6 5.4 4.8
Electrical tilt ° 2–10, continuously adjustable
Sidelobe suppression for first sidelobe °T 2 ... 6 ... 10 2 ... 6 ... 10 2 ... 6 ... 10 2 ... 6 ... 10 2 ... 6 ... 10
above main beam dB 14 ... 15 ... 16 14 ... 15 ... 17 15 ... 16 ... 17 17 ... 18 ... 18 15 ... 17 ... 18
Impedance Ω 50
VSWR < 1.5
Isolation: Intrasystem dB > 28 > 30
Isolation: Intersystem dB > 30 (790–960 // 1710–2690 MHz)
Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier)
Max. effective power per port W 200 (at 50 °C ambient temperature)
Max. effective power for the antenna 400 (at 50 °C ambient temperature)

Mechanical specifications

Input 4 x 7-16 female (long neck)

Connector position Bottom
Adjustment mechanism 2 x, Position bottom
Subject to alteration.

continuously adjustable
Wind load (at Rated N | lbf Frontal: 260 | 58
Wind Speed: 150 km/h) Maximal: 415 | 93
Max. wind velocity km/h 200
mph 124
Height / width / depth mm 1403 / 300 / 152
Y1 inches 55.2 / 11.8 / 6.0
R1 Category of
936.4850/b

M (Medium)
mounting hardware
Weight kg 18 / 20 (clamps incl.)
Correlation Table lb 39.7 / 44.1 (clamps incl.)
Packing size mm 1726 x 322 x 190
Frequency range Array Connector inches 68.0 x 12.7 x 7.5
Scope of supply Panel and 2 units of clamps
790– 960 MHz R1 1–2 for 42 – 115 mm |
1710–2690 MHz Y1 3–4 1.7– 4.5 inches diameter

Page 2 of 3 80010664 www.kathrein.com

KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
 Accessories
General Information

Accessories (order separately if required) 2) 1) ’ 9 | 0.4

1) 2) 64 | 2.5
Remarks Weight approx. Units per
Type No. Description
mm | inches kg | lb antenna

85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
737978 1 downtilt kit Downtilt angle: 0° – 15° 2.3 | 5.1 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.

1403 | 55.2
1433 | 56.4
1473 | 58.0
Wall mounting: No additional mounting kit needed.

Material: Reflector screen: Aluminum.

Fiberglass housing: It covers totally the internal antenna components.
The special design reduces the sealing areas to a minimum and
guarantees the best weather protection. Fiberglass material guarantees
optimum performance with regards to stability, stiffness, UV resistance
and painting. The color of the radome is light grey.
All nuts and bolts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.

Adjustment mechanism
with integrated scale

All dimensions
in mm | inches

Layout of interface:

t 790-960 1710-2690
Til Ti
lt
152 | 6.0 *

173 | 6.8 *
108 | 4.3
49 | 1.9
46 | 1.8
Subject to alteration.

101 | 4.0
221 | 8.7
244 | 9.6
936.4850/b

300 | 11.8 *

Bottom view
* Dimensions refer to radome
All dimensions in mm | inches

Any previous data sheet issues have now become invalid. 80010664 Page 3 of 3
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
 Mounting Hardware
Clamp Included in the Scope of Supply

Suitable for mast diameter mm 42 – 115

inches 1.65 – 4.53
Antenna – mast distance mm 20 – 25
inches 0.79 – 0.98
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight kg 1.1
lb 2.43

152 | 5.98

100 | 3.94
40 | 1.57

0.79–0.98
72 | 2.8

20–25
40 | 1.57

15
2–1
∅ 4 4.53
–
1.65

M10 ⇒ MA = 25 Nm

M8 ⇒ MA = 12 Nm
35 | 1.38
64 | 2.52
125 | 4.92

20–25
0.79–0.98
936.3920e | Subject to alteration.

Please note: K
 athrein does not recommend to use counter nuts. All dimensions in mm | inches
The additional nuts supplied are only meant as spares.

Any previous data sheet issues have now become i­ nvalid. 738546 Page 1 of 1
KATHREIN SE | Anton-Kathrein-Straße 1–3 | 83022 Rosenheim, Germany | Phone +49 8031 184-0 | www.kathrein.com | [email protected]
 General Instructions
for Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

1
2

2
 Twist protection.  Thread for fixing the pro­tective To set the downtilt angle exactly,
 Downtilt spindle with integrated cap or the RCU (Remote Control you must look horizontally at the
scale. Unit). scale. The lower edge of the gear­
 Gearwheel for RCU power drive. wheel must be used for alignment.

Manual adjustment procedure:

0° – max.°

0° – max.°

Remove the protective cap and the Set downtilt angle by rotating the Screw on the twist protection and
twist protection completely. gearwheel. the protective cap again.

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

936.4037b | Subject to alteration.

For a description of RCU installation please refer to the respective data sheet.
Page 1 of 2
KATHREIN SE | Anton-Kathrein-Straße 1–3 | 83022 Rosenheim, Germany | Phone +49 8031 184-0 | www.kathrein.com | [email protected]
General Instructions
for Feederline and RCU Installation
for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable
wrench width.

Description of bottom end cap (exemplary picture):

Adjustment mechanism
(protective cap removed) Ventilation hole

Spindle with tilting scale

Colour coding:
Correlation of each RF input to:
– the corresponding adjustment mechanism
7-16 female (long neck) – the frequency range
– the polarization

Installation of the feederline connector and RCU (optional):

In order to protect the adjustment mechanism, the protective caps have to be attached during
­feederline installation!
Kathrein installation set: Type No. 85010077
Set has to be ordered separately!
Set consists of three spanners of divers width
27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches
1/2˝ square actuation
according to
DIN 3120 Form C

32 | 1.3
936.4037b | Subject to alteration.

Carefully place the connector and After feederline installation, the

fix the nut using a torque-wrench optional remote control units
(according to the manufacturers (RCUs) can be mounted. .6
|1
guidelines). 41
27
| 1.
1

All dimensions in mm | inches

These tools are suitable for 7-16 connectors with a wrench size of
27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a
wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on
­connector manufacturers’ specifications, respectively the RCU nut
with a torque range of 15 – 18 Nm.

Page 2 of 2 Any previous data sheet issues have now become ­invalid.
KATHREIN SE | Anton-Kathrein-Straße 1–3 | 83022 Rosenheim, Germany | Phone +49 8031 184-0 | www.kathrein.com | [email protected]