HT11 THRU HT18

1.0 AMP. High Efficient Rectifiers

Voltage Range
50 to 1000 Volts
Current
1.0 Ampere
TS-1
Features
 Low forward voltage drop
 High current capability
 High reliability
 High surge current capability
Mechanical Data
 Case: Molded plastic TS-1
 Epoxy: UL 94V-O rate flame retardant
 Lead: Axial leads, solderable per MIL-STD-
202, Method 208 guaranteed
 Polarity: Color band denotes cathode end
 High temperature soldering guaranteed:
260oC/10 seconds/.375”,(9.5mm) lead
lengths at 5 lbs., (2.3kg) tension
 Mounting position: Any
 Weight: 0.20 gram Dimensions in inches and (millimeters)

Maximum Ratings and Electrical Characteristics

Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number Symbol HT HT HT HT HT HT HT HT Units
11 12 13 14 15 16 17 18
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 300 400 600 800 1000 V
Maximum RMS Voltage VRMS 35 70 140 210 280 420 560 700 V
Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 800 1000 V
Maximum Average Forward Rectified
Current .375 (9.5mm) Lead Length I(AV) 1.0 A
@TA = 55℃
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated IFSM 30 A
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 1.0A
VF 1.0 1.3 1.7 V
Maximum DC Reverse Current @ TA=25℃ 5.0 uA
at Rated DC Blocking Voltage @ TA=100℃
IR
100 uA
Maximum Reverse Recovery Time ( Note 1 ) Trr 50 75 nS
Typical Junction Capacitance ( Note 2 ) Cj 20 15 pF
Typical Thermal Resistance ( Note 3) RθJA 100 ℃/W
Operating Temperature Range TJ -65 to +150 ℃
Storage Temperature Range TSTG -65 to +150 ℃
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
3. Mount on Cu-Pad Size 5mm x 5mm on PCB.
- 310 -
 RATINGS AND CHARACTERISTIC CURVES (HT11 THRU HT18)

FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM FIG.2- MAXIMUM AVERAGE
50W 10W FORWARD CURRENT DERATING
NONINDUCTIVE NONINDUCTIVE trr

AVERAGE FORWARD CURRENT. (A)

+0.5A 2.0
Single Phase
(-) Half Wave 60Hz
DUT Resistive or
(+) PULSE 0 Inductive Load
50Vdc GENERATOR 0.375" (9.5mm)
(approx) (NOTE 2) -0.25A 1.0 Lead Length
(-) 1W OSCILLOSCOPE
NON (NOTE 1) (+)
INDUCTIVE

-1.0A 0
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf 0 25 50 75 100 125 150 175
1cm
2. Rise Time=10ns max. Sourse Impedance= SET TIME BASE FOR AMBIENT TEMPERATURE. ( C)
o

50 ohms 5/ 10ns/ cm

FIG.3- TYPICAL REVERSE CHARACTERISTICS FIG.4- TYPICAL FORWARD CHARACTERISTICS

1000 100
INSTANTANEOUS FORWARD CURRENT. (A)
INSTANTANEOUS REVERSE CURRENT. ( A)

100 10

HT15

Tj=100 0C
10 1

Tj=75 0C

1 0.1 HT16~HT18

HT11~HT14
Tj=25 0C

0.1 0.01
0 20 40 60 80 100 120 140 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FORWARD VOLTAGE. (V)

FIG.5- MAXIMUM NON-REPETITIVE FORWARD FIG.6- TYPICAL JUNCTION CAPACITANCE

SURGE CURRENT
40 70
PEAK FORWARD SURGE CURRENT. (A)

35 60
JUNCTION CAPACITANCE.(pF)

30 50
8.3ms Single Half Sine Wave
JEDEC Method
25 40

30 HT
20 11~
H T15
HT1
15 20 6~H
T18

10 10

0 0
1 2 5 10 20 50 100 0.1 0.5 1 2 5 10 20 50 100 200 500 1000
NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE. (V)

- 311 -