WCS1700
Hall Effect Base Linear Current Sensor
Features:
Diameter 9.0 mm conductor through hole
Output voltage proportional to AC and DC current
Wide sensing current range 0~70A at 5V volt.
High sensitivity 33 mV/A
Wide operating voltage range 3.0~12 V.
Low operating current 3mA
Isolation voltage 4000V
Ratiometric output from supply voltage
23K Hz Bandwidth
Functional Description :
The Winson WCS1700 current sensor provides economical and precise
solution for both DC and AC current sensing in industrial, commercial and
communications systems. The unique package provides easy implementation
without breaking original system and makes current sensing possible. Typical
applications include motor control, load detection and management,
over-current fault detection and any intelligent power management system
etc…
The WCS1700 consists of a precise, low-temperature drift linear hall
sensor IC with temperature compensation circuit and a diameter 9.0mm
through hole. Users can use system’s own electric wire by pass it through this
hole to measure passing current. This design allows system designers to
monitor any current path without breaking or changing original system layout
at all. Any current flowing through this hole will generate a magnetic field
which is sensed by the integrated Hall IC and converted into a proportional
voltage.
The terminals of the conductive path are electrically isolated from the
sensor leads. This allows the WCS1700 current sensor to be used in
applications requiring electrical isolation without the use of opto-isolators or
other costly isolation techniques and make system more competitive in cost.
Winson reserves the right to make changes to improve reliability or manufacturability.
© Winson, 2020/9/29 Page 1
WCS1700
Absolute Maximum Range
Supply Voltage, Vdd ----------------------------- 14V
Pass Through Wire Diameter ---------------- 9mm
Output Current Sink--------------------------- 0.4mA
Output Current Source-------------------------- 2mA
Basic Isolation Voltage ---------------------- 4000V
Operating Temperature Range, Ta ------------------
+IP Current Path
----------------------------------------- -20ºC to +125ºC
Vdd Vout
Gnd Storage Temperature Range, Ts ---------------------
----------------------------------------- -65ºC to +150ºC
Power Dissipation, Pd -----------------------------1W
Vout vs. Primary Current
Vout
Vdd-0.3V
Order Information ( Vdd = 5V )
Vout
Slop = 33mV/A
Part No. Sensitivity Current range
½ Vdd DC: ±0 ~ 70A
-A +A WCS1700 33 mV/A
AC: rms 50A
0.3V
0A
Function Block:
Winson reserves the right to make changes to improve reliability or manufacturability.
© Winson, 2020/9/29 Page 2
WCS1700
Electrical Characteristics: (T=+25˚C, Vdd=5.0V )
Characteristic Symbol Test Conditions Min Typ Max Units
Supply Voltage Vdd ─ 3.0 ─ 12 V
Supply Current Isupply IP =0 A ─ 3.5 6.0 mA
Zero Current Vout V0G IP =0 A (DC Mode 2.4 2.5 2.6 V
Conductor Through Hole ─ ─ ─ 9.0 ─ mm²
Sensitivity Sens IP= +-10 A 28 33 38 mV/A
Bandwidth BW ─ － 23 － kHz
Vdd=5V (DC Mode) － ±70 －
Measurable Current Range MR A
Vdd=5V (AC RMS ) － 50 －
Temperature Drift △Vout Ip =0 A － ±0.5 － mV/℃
VNp-p Ip =0 A — 7.5 —
Output Noise mV
VNp-p(0.01uF) Ip =0 A, C = 0.01uF — 1 —
[Link] output-voltage measurements are made with a voltmeter having an input impedance of at least 100kΩ
2. Do not apply any ‘resistor load’ on output pin, it will degrade IC’s performance.
Characteristic Diagrams:
Winson reserves the right to make changes to improve reliability or manufacturability.
© Winson, 2020/9/29 Page 3
WCS1700
Application Circuit:
+IP Current Path
Vdd
Vout
GND C
Capacitor C(0.01uF~0.1uF) is recommend to be connected between Vout and
GND to reduce output noise.
Winson reserves the right to make changes to improve reliability or manufacturability.
© Winson, 2020/9/29 Page 4
WCS1700
Package Information:
(Unit: mm)
Vdd Vout
Gnd
PCB Layout Reference View (Top View)
4.5
1.0 ɸ2.0
0.7 Vout
1.5
3.3
1.27 ɸ0.5
Vdd
6.5 6.5
13
WCS Application Note : please refer to Winson Website -> Products->
Application Note -> WCS Application Note :
[Link]
Winson reserves the right to make changes to improve reliability or manufacturability.
© Winson, 2020/9/29 Page 5
