PRODUCT DATA SHEET December 16, 2021 (Revision of April 13, 2021)

SIGMACOVER™ 410/SIGMACOVER™ 410 LT

DESCRIPTION
Two-component, high solids, high-build, polyamide cured epoxy coating

PRINCIPAL CHARACTERISTICS
• General-purpose epoxy buildcoat in protective coating systems, for steel and concrete structures exposed to
atmospheric land or marine conditions
• Excellent durability
• Can be recoated with various two-component and conventional coatings, even after long weathering periods
• Easy application by airless spray
• Good drying- and curing properties at low substrate temperature (down to –5°C (23°F))

COLOR AND GLOSS LEVEL

• MIO and a selected range of colors
• Flat

Note: Epoxy coatings will chalk and fade upon exposure to sunlight, elevated temperatures, or chemical exposure.
Discoloration and normal chalking does not impact performance. Light colors will darken over time. Some batch-to-batch
variation in color is to be expected. Color matches are approximate.

BASIC DATA AT 20°C (68°F)

Data for mixed product

Number of components Two

Mass density 1.5 kg/l (12.5 lb/US gal), depending on color

MIO: 1.8 kg/l (15.0 lb/US gal)
Volume solids 80 ± 2%

VOC (Supplied) Directive 2010/75/EU, SED: max. 126.0 g/kg

UK PG 6/23(92) Appendix 3: max. 240.0 g/l (approx. 2.0 lb/US gal)
Recommended dry film thickness 75 - 200 µm (3.0 - 8.0 mils) depending on system

Theoretical spreading rate 10.7 m²/l for 75 µm (428 ft²/US gal for 3.0 mils)

Overcoating Interval See overcoating tables

See overcoating tables
Full cure after 7 days

Shelf life Base: at least 24 months when stored cool and dry
Hardener: at least 24 months when stored cool and dry

Notes:
- See ADDITIONAL DATA – Spreading rate and film thickness
- See ADDITIONAL DATA – Overcoating intervals
- See ADDITIONAL DATA – Curing time
- See ADDITIONAL DATA - Drying time

Ref. 6823 Page 1/5

PRODUCT DATA SHEET December 16, 2021 (Revision of April 13, 2021)

SIGMACOVER™ 410/SIGMACOVER™ 410 LT

RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES

Substrate conditions
• Suitable primer must be dry and free from any contamination
• Surface of previous coat should be sufficiently roughened if necessary
• When applied to zinc silicate, a mist coat and full coat technique is required

Substrate temperature
• Substrate temperature during application and curing down to -5°C (23°F) is acceptable; provided the substrate is free
from ice and dry
• Substrate temperature during application and curing should be at least 3°C (5°F) above dew point

INSTRUCTIONS FOR USE

Mixing ratio by volume: base to hardener 80:20 (4:1)
• The temperature of the paint should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain
application viscosity
• Adding too much thinner results in reduced sag resistance and slower cure
• Thinner should be added after mixing the components

Induction time
None

Pot life
6 hours at 20°C (68°F)

Note: See ADDITIONAL DATA – Pot life

Airless spray

Recommended thinner
THINNER 91-92

Volume of thinner
0 - 10%

Nozzle orifice
Approx. 0.46 – 0.53 mm (0.018 – 0.021 in)

Nozzle pressure
20.0 - 25.0 MPa (approx. 200 - 250 bar; 2901 - 3626 p.s.i.)

Ref. 6823 Page 2/5

PRODUCT DATA SHEET December 16, 2021 (Revision of April 13, 2021)

SIGMACOVER™ 410/SIGMACOVER™ 410 LT

Brush/roller
• Application by brush may show brush marking, due to the thixotropic nature of the paint and is most suitable to small
areas, tight angle areas or for stripe coating or touch-up
• Application by roller will leave roller marking and is suitable for minimum DFT requirements only
• A roller suitable for epoxy application must be used

Recommended thinner
THINNER 91-92

Volume of thinner
0 – 5%

Cleaning solvent
THINNER 90-53

ADDITIONAL DATA

Spreading rate and film thickness

DFT Theoretical spreading rate

75 µm (3.0 mils) 10.7 m²/l (428 ft²/US gal)

150 µm (6.0 mils) 5.3 m²/l (214 ft²/US gal)
200 µm (8.0 mils) 4.0 m²/l (160 ft²/US gal)

Overcoating interval for DFT up to 200µm (8 mils) - SIGMACOVER 410

Overcoating with... Interval 5°C (41°F) 10°C (50°F) 20°C (68°F) 30°C (86°F) 40°C (104°F)

various two-pack epoxy Minimum 36 hours 24 hours 8 hours 6 hours 4 hours

and polyurethane Maximum Extended Extended Extended Extended Extended
coatings

Overcoating interval for DFT up to 200µm (8 mils) -SIGMACOVER 410LT

Overcoating with... Interval -5°C (23°F) 0°C (32°F) 5°C (41°F) 10°C (50°F) 15°C (59°F)

various two-pack epoxy Minimum 48 hours 24 hours 16 hours 12 hours 8 hours

and polyurethane Maximum Extended Extended Extended Extended Extended
coatings

Notes:
- This product has an unlimited overcoating interval provided the surface is free from chalking and other contaminations
- In case of exposure to direct sunlight or when the surface is contaminated it is recommended that the surface be cleaned and
roughened to ensure good adhesion of the subsequent coating

Ref. 6823 Page 3/5

PRODUCT DATA SHEET December 16, 2021 (Revision of April 13, 2021)

SIGMACOVER™ 410/SIGMACOVER™ 410 LT

Curing time for DFT up to 200µm (8 mils) - SIGMACOVER 410

Substrate temperature Dry to touch Dry to handle Full cure

5°C (41°F) 12 hours 30 hours 20 days

10°C (50°F) 6 hours 24 hours 14 days
15°C (59°F) 4 hours 10 hours 10 days
20°C (68°F) 3 hours 8 hours 7 days
30°C (86°F) 2 hours 6 hours 5 days
40°C (104°F) 1.5 hours 4 hours 3 days

Curing time for DFT up to 200µm (8 mils) - SIGMACOVER 410LT

Substrate temperature Dry to touch Dry to handle Full cure

-5°C (23°F) 16 hours 24 hours 20 days

0°C (32°F) 11 hours 16 hours 14 days
5°C (41°F) 6 hours 10 hours 10 days
10°C (50°F) 4 hours 8 hours 7 days
15°C (59°F) 3 hours 5 hours 5 days

Notes:
- Ambient temperature during application at -5°C (23°F) is acceptable; however curing to hardness takes longer and complete cure will
be reached when the temperature increases
- Adequate ventilation must be maintained during application and curing

Pot life (at application viscosity)

Mixed product temperature Pot life

10°C (50°F) 12 hours

15°C (59°F) 8 hours
20°C (68°F) 6 hours
25°C (77°F) 4 hours
30°C (86°F) 3 hours
40°C (104°F) 2 hours

SAFETY PRECAUTIONS
• See Material Safety Data Sheet and product label for complete safety and precaution requirements
• This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact
between the wet paint and exposed skin or eyes

Ref. 6823 Page 4/5

PRODUCT DATA SHEET December 16, 2021 (Revision of April 13, 2021)

SIGMACOVER™ 410/SIGMACOVER™ 410 LT

WORLDWIDE AVAILABILITY
It is always the aim of PPG Protective and Marine Coatings to supply the same product on a worldwide basis. However, slight
modification of the product is sometimes necessary to comply with local or national rules/circumstances. Under these
circumstances an alternative product data sheet is used.

REFERENCES
• EXPLANATION TO PRODUCT DATA SHEETS INFORMATION SHEET 1411

WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifications for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the
rightful claim of any third person for infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER
STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE,
ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the
applicable shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyer’s failure to notify PPG of such non-conformance as required herein shall bar
Buyer from recovery under this warranty.

LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT. The information in this sheet is intended for guidance only and is based upon
laboratory tests that PPG believes to be reliable. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. All recommendations or
suggestions relating to the use of the PPG product, whether in technical documentation, or in response to a specific inquiry, or otherwise, are based on data, which to the best of PPG’s knowledge, is reliable. The
product and related information is designed for users having the requisite knowledge and industrial skills in the industry and it is the end-user’s responsibility to determine the suitability of the product for its own
particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk. PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such use or the contents of this information (unless there are written agreements
stating otherwise). Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. This sheet supersedes all previous versions and it is the
Buyer’s responsibility to ensure that this information is current prior to using the product. Current sheets for all PPG Protective & Marine Coatings Products are maintained at [Link]. The English text of
this sheet shall prevail over any translation thereof.

The PPG logo, and all other PPG marks are property of the PPG group of companies. All other third-party marks are property of their respective owners.

Ref. 6823 Page 5/5