DIAGNOSTICS – ECD SYSTEM (HILUX/1KD–FTV, 2KD–FTV (TASA 05–27
MADE FOR ARGENTINA))
05L6N–14
READING REGISTERED DATA
NOTICE:
S When an injector is replaced, the injector’s compensation code must be input into the ECM.
When the ECM is replaced, all of the existing injector compensation codes must be input into
the new ECM.
S Injector compensation codes are unique, 30–digit, alphanumeric values printed on the head
portion of each injector. If an incorrect injector compensation code is input into the ECM, the
engine may rattle or engine idling may become rough. In addition, engine failure may occur and
the life of the engine may be shortened.
1. AFTER REPLACING INJECTOR(S) WITH A NEW ONE(S), INPUT THE COMPENSATION CODE(S)
OF INJECTOR(S) INTO ECM AS FOLLOWS:
(a) Input the compensation code(s), which is/are imprinted on the head portion(s) of the new injector(s),
to the intelligent tester II.
(b) Input the new compensation code(s) into the ECM using the tester (see page 05–32).
(c) Turn the ignition switch OFF and then turn the intelligent tester II OFF.
(d) Wait for at least 30 seconds.
(e) Turn the ignition switch ON and then turn the intelligent tester II ON.
(f) Clear DTC P1601/89 stored in the ECM using the intelligent tester II (see page 05–50).
2. WHEN REPLACING ECM WITH A NEW ONE, INPUT ALL INJECTOR’S COMPENSATION CODES
INTO NEW ECM AS FOLLOWS:
(a) Prior to replacing the ECM, use the intelligent tester II to read and save each injector’s compensation
code. The codes are stored in the original ECM (see page 05–27).
(b) After installing a new ECM, input the saved compensation codes into the new ECM using the tester
(see page 05–32).
(c) Turn the ignition switch OFF and then turn the intelligent tester II OFF.
(d) Wait for at least 30 seconds.
(e) Turn the ignition switch ON and then turn the intelligent tester II ON.
(f) Clear DTC P1601/89 stored in the ECM using the tester (see page 05–50).
HINT:
S Each injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM
uses the compensation codes to balance the different fuel injections between each injector.
S When you first turn the ignition switch ON after replacing the ECM or an injector(s), DTC P1601/89 is
set. This is to inform you that an injector compensation code(s) must be registered. Manually clear the
DTC upon completion of the compensation code registration.
HILUX REPAIR MANUAL (Argentina) (DR201E)
05–28 DIAGNOSTICS – ECD SYSTEM (HILUX/1KD–FTV, 2KD–FTV (TASA
MADE FOR ARGENTINA))
How to read and save injector compensation codes using intelligent tester ll
(Perform prior to replacing ECM)
START
Select function
Select cylinder number
Read
Display compensation code
to be saved Read error
If compensation codes If compensation codes
are not stored in tester are already stored in tester
Confirm code save Confirm code overwrite
Save
Option dialog: continue
Read and save other reading/saving operation Save error
compensation codes
End reading and saving of
compensation codes
END
Proceed to registration procedure (see page 05–32)
A93042
HILUX REPAIR MANUAL (Argentina) (DR201E)
DIAGNOSTICS – ECD SYSTEM (HILUX/1KD–FTV, 2KD–FTV (TASA 05–29
MADE FOR ARGENTINA))
HINT:
The following operation is available with ECMs that can transmit the registered injector compensation codes
to the intelligent tester II.
Example: Injector 3. READ AND SAVE INJECTOR COMPENSATION
Compensation Code CODES
(a) Connect the intelligent tester II to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the intelligent tester II ON.
NOTICE:
Do not start the engine.
HINT:
A85701 The injector compensation code is imprinted on the head por-
tion of each injector.
(d) Enter menu options in this order: Auto / Pick Up / Engine
/ Utility / Injector Compensation.
(e) Press Next.
G36522
(f) Press Next again to proceed.
G36523
HILUX REPAIR MANUAL (Argentina) (DR201E)
05–30 DIAGNOSTICS – ECD SYSTEM (HILUX/1KD–FTV, 2KD–FTV (TASA
MADE FOR ARGENTINA))
(g) Select Read Compensation Code.
(h) Press Next.
G36524
(i) Select the number of the cylinder corresponding to the in-
jector compensation code that you want to read.
(j) Press Next.
HINT:
The reading process may fail due to a problem with the wire har-
ness or a bad connection with the DLC3. Check the wire har-
ness and the DLC3 connection. If no problem is found, the ECM
may be malfunctioning. Check the ECM and restart this opera-
tion.
G36525
(k) Check the injector compensation code (30–digit alphanu-
meric value) displayed on the tester screen.
(l) Press Save.
G36526
HILUX REPAIR MANUAL (Argentina) (DR201E)
DIAGNOSTICS – ECD SYSTEM (HILUX/1KD–FTV, 2KD–FTV (TASA 05–31
MADE FOR ARGENTINA))
(m) If no injector compensation code for the cylinder exists in
the tester:
(1) Check that the compensation code displayed on
the tester screen is correct.
(2) Press Save (proceed to step (o)).
HINT:
The saving process may fail due to a problem with the wire har-
ness or a bad connection with the DLC3. Check the wire har-
ness and the DLC3 connection. If no problem is found with ei-
ther, the ECM may be malfunctioning. Check the ECM and
restart this operation.
A96470
(n) If another injector compensation code already exists in
the tester:
(1) Check that the compensation code displayed on
the tester screen is correct.
HINT:
The existing compensation code is overwritten with the new
compensation code and is deleted from the tester.
(2) Press Replace.
HINT:
The saving process may fail due to a problem with the wire har-
ness or a bad connection with the DLC3. Check the wire har-
ness and the DLC3 connection. If no problem is found with ei-
ther, the ECM may be malfunctioning. Check the ECM and
A93040 restart this operation.
(o) If you want to read and save other injector compensation
codes for other cylinders, press Next to continue. To finish
this operation, press Cancel.
G36526
HILUX REPAIR MANUAL (Argentina) (DR201E)
