Dimensions: [mm] Recommended Hole Pattern: [mm] Absolute Maximum Ratings (Ambient Temperature 25°C):

Properties Test conditions Value Unit

Power Dissipation PDiss 78 mW
detail A
Cathode Peak Forward Current IF Peak duty/ 10 @ 1 kHz 100 mA
O1
Continuous Forward Current IF 30 mA
Reverse Voltage VREV 5 V

1,0 typ.
2,54 typ. 1,2 typ.
ESD Threshold/ Human Body VESD HBM 2000 V
Model

O 5,0 ±0,25
2,54
Optical Properties:
Chip Technology AlInGaP
11,7 u0,4

Emitting Color Red

1,0 typ. Lens Type Waterclear
8,6 ±0,25

Scale - 5:1
A
25,4 ±0,25

Schematic:
1,0 Min.

General Information:
+ - Operating Temperature -40 up to +85 °C
q0,5 typ.
Storage Conditions (in original < 40 °C ; < 75 % RH
- +
packaging)
1 2
Storage Conditions (for single -40 up to +100 °C
parts)
5,8 ±0,25

Moisture Sensitivity Level (MSL) 1

Scale - 1,3:1

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 1/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Electrical & Optical Properties: Viewing Angle:
Value
Properties Test conditions Unit
min. typ. max.
Peak Wavelength λPeak 20 mA 631 nm
Dominant Wavelength λDom 20 mA 623 nm
Luminous Intensity IV 20 mA 1800 5000 mcd
Forward Voltage VF 20 mA 1.9 2.6 V
Spectral Bandwidth Δλ 20 mA 15 nm
Reverse Current IREV 5V 50 µA
Viewing Angle Phi 0° 2θ50% 20 mA 30 ° -15° 0° 10°
100 15°
20°

90 30°

80 40°

Relative Luminous Intensity (%)

45°
70
50°
60

50 60°

40
70°
30

20
80°
10

90°
-90 -45 0 10 20 30 40 50 60 70 80 90 100

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 2/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
 Spectral: Forward Current vs. Forward Voltage:
35

30

100

25

80

Forward Current [mA]

20
Relative Intensity [%]

60

40
15

20

10
0
400 450 500 550 600 650 700 750

Wavelength [nm]
5

0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Forward Voltage [V]

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 3/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
 Luminous Intensity vs. Forward Current: Derating Curve:
10000 25

9000

8000 20

7000
Luminous Intensity [mcd]

Forward current (mA)

6000 15

5000

4000 10

3000

2000 5

1000

0 0
0 5 10 15 20 25 30 35 0 20 40 60 80 100
Forward Current [mA] Ambient temperature Ta (°C)

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 4/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
 Packaging Specification - Bulk: [mm]

Packaging Type Packaging Unit

Size 5 mm with Stopper Bulk 500

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 5/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
 Classification Wave Soldering Profile: Classification Wave Soldering Profile:
Profile Feature Pb-Free Assembly Sn-Pb Assembly
tp
Preheat Temperature Min Ts min 100 °C 100 °C
Tp Preheat Temperature Typical Ts typical 120 °C 120 °C
First Wave Second Wave Preheat Temperature Max Ts max 130 °C 130 °C
Preheat Time ts from Ts min to Ts max ts 70 seconds 70 seconds
Ramp-up Rate ΔT 150 °C max. 150 °C max.
Peak Temperature Tp 245 °C - 260 °C 235 °C - 260 °C
Time of actual peak temperature tp 5-8 seconds max. 3-6 seconds max.
Temperature

Ramp-down Rate, Min ~ 2 K/ second ~ 2 K/ second

Ts max Ramp-down Rate, Typical ~ 3.5 K/ second ~ 3.5 K/ second
Ts typical Ramp-down Rate, Max ~ 5 K/ second ~ 5 K/ second
Ts min Time 25 °C to 25 °C 4 minutes 4 minutes
Applied cycles 1 cycle max.
refer to EN61760-1:2006

Preheat area Cool down area

Time
typical temperature procedure
min temperature procedure
max temperature procedure

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 6/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Cautions and Warnings: • If the product is potted in the customer application, the potting material may shrink or expand during and after hardening. Shrinking
could lead to an incomplete seal, allowing contaminants into the optoelectronic component body, pins or termination. Expansion could
damage the optoelectronic component body, pins or termination. We recommend a manual inspection after potting to avoid these
The following conditions apply to all goods within the product series of Optoelectronic effects.
Components of Würth Elektronik eiSos GmbH & Co. KG:
Storage Conditions:
General:
• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer
• This optoelectronic component is designed and manufactured for use in general electronic equipment. degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of
• Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any shipment.
equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, • Do not expose the optoelectronic component to direct sunlight.
ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are • The storage conditions in the original packaging are defined according to DIN EN 61760-2.
especially required and/or if there is the possibility of direct damage or human injury. • For a moisture sensitive component, the storage condition in the original packaging is defined according to IPC/JEDEC-J-STD-033. It is
• Optoelectronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. also recommended to return the optoelectronic component to the original moisture proof bag and reseal the moisture proof bag again.
• The optoelectronic component is designed and manufactured to be used within the datasheet specified values. If the usage and
operation conditions specified in the datasheet are not met, the component may be damaged or dissolved. Handling:
• Do not drop or impact the components, as the optoelectronic component body may flake apart.
• Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth • Violation of the technical product specifications such as exceeding the nominal rated current, will void the warranty.
Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and • The product design may influence the automatic optical inspection.
sustainability over time. • Certain optoelectronic component surfaces consist of soft material. Pressure on the top surface has to be handled carefully to prevent
• The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the negative influence to the function and reliability of the optoelectronic components.
authority of the customer. All technical specifications for standard products also apply to customer specific products. • ESD prevention methods need to be applied for manual handling and processing by machinery.
• Resistors for protection are obligatory.
Product specific: • Luminaires in operation may harm human vision or skin on a photo-biological level. Therefore direct light impact shall be avoided. All
products are additionally certified as risk groups 0 to 2 according to DIN EN 62471:2008.
Soldering: • In addition to optoelectronic components testing, products incorporating these devices have to comply with the safety precautions given
in IEC 60825-1 and IEC 62471.
• The solder profile must comply with the Würth Elektronik technical soldering specification. All other profiles will void the warranty.
• All other soldering methods are at the customers’ own risk. Technical specification:

Cleaning and Washing: • The typical and/or calculated values of technical parameters can only reflect statistical figures. The actual parameters of each single
product, may differ from the typical and/or calculated values or the typical characteristic line.
• Washing agents used during the production to clean the customer application might damage or change the characteristics of the • On each reel, only one bin is sorted and taped. The bin is defined on intensity, chromaticity coordinate or wavelength and forward
optoelectronic component body, marking or plating. Washing agents may have a negative effect on the long-term functionality of the voltage.
product. • In order to ensure highest availability, the reel binning of standard deliveries can vary. A single bin cannot be ordered. Please contact us
• Using a brush during the cleaning process may break the optoelectronic component body. Therefore, we do not recommend using a in advance, if you need a particular bin sorting before placing your order to clarify the lead time, MOQ and pricing.
brush during the PCB cleaning process.
These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.
However, no responsibility is assumed for inaccuracies or incompleteness.
Potting:

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 7/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Important Notes 6. Product Life Cycle

Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a
The following conditions apply to all goods within the product range of Würth Elektronik standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage
eiSos GmbH & Co. KG: about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be
available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product
1. General Customer Responsibility availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not
apply in the case of individual agreements deviating from the foregoing for customer-specific products.
Some goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain
application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the 7. Property Rights
areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The
responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this All the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as
fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth
characteristics described in the product specification is valid and suitable for the respective customer application or not. Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or
implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination,
2. Customer Responsibility related to Specific, in particular Safety-Relevant Applications application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.

It has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime 8. General Terms and Conditions
cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.
In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth
failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable Elektronik eiSos Group”, last version available at [Link].
design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic
component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be
downloaded at [Link].

3. Best Care and Attention

Any product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.

4. Customer Support for Product Specifications

Some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve
specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales
person in charge should be contacted who will be happy to support in this matter.

5. Product R&D
Due to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the
Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries
regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the
customer as per Section 1 and 2 remains unaffected.

CREATED CHECKED GENERAL TOLERANCE PROJECTION

Würth Elektronik eiSos GmbH & Co. KG METHOD
EMC & Inductive Solutions DaSc PLD DIN ISO 2768-1m

Max-Eyth-Str. 1 DESCRIPTION
74638 Waldenburg
Germany WL-TMRW THT Mono-color Round
Tel. +49 (0) 79 42 945 - 0
Waterclear ORDER CODE

[Link]
eiSos@[Link] 151053RS03000
SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

5 mm 001.010 Valid 2018-11-02 eiPal 8/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.