IECEx Certificate

of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification System for Explosive Atmospheres
for rules and details of the IECEx Scheme visit [Link]

Certificate No.: IECEx BAS 14.0097X Page 1 of 5 Certificate history:

Issue 2 (2018-12-17)
Status: Current Issue No: 3 Issue 1 (2017-07-11)
Issue 0 (2014-12-09)
Date of Issue: 2020-10-12

Applicant: WEG Equipamentos Eletricos S.A

Av. Prefeito Waldemar Grubba
3000. Jaragua do Sul
SC
CEP: 89256-900
Brazil

Equipment: The W60 Range of Induction motors – Frame Sizes 315 to 1000

Optional accessory:

Type of Protection: Equipment protection by increased safety "e", Equipment protection by enclosure ‘t’

Marking: Ex ec IIC T3 or T4 Gc Tamb*

Ex tc IIIB T125°C or T160°C Dc Tamb*
Ex tb IIIC T125°C or T160°C Db Tamb*

*See annex for ambient temperature.

Approved for issue on behalf of the IECEx R S Sinclair

Certification Body:

Position: Technical Manager

Signature:
(for printed version)

Date:

1. This certificate and schedule may only be reproduced in full.

2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting [Link] or use of this QR Code.

Certificate issued by:

SGS Baseefa Limited
Rockhead Business Park
Staden Lane
Buxton, Derbyshire, SK17 9RZ
United Kingdom
 IECEx Certificate
of Conformity
Certificate No.: IECEx BAS 14.0097X Page 2 of 5

Date of issue: 2020-10-12 Issue No: 3

Manufacturer: WEG Equipamentos Eletricos S.A

Av. Prefeito Waldemar Grubba
3000. Jaragua do Sul
SC
CEP: 89256-900
Brazil

Additional WEG Euro - Industria Electrica S.A WEG Industries India Pvt Limited WEG (Nantong) Electric Motor
manufacturing Rua Eng Frederico Ulrich Plot e-20, Moranapalli Village Manufacturing Co., Ltd.
locations: Zona Industrial da Maia, Sector V Sipcot Phase II ExpII 128#, Xin Kai South Rd.
4470-605 Maia. Krishnagiri Dist, Hosur Nantong ETDA, Jiangsu Province
Portugal Tamil Nadu P.R. China Zip : 226010
635109 China
India

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the
IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and
found to comply with the IECEx Quality system [Link] certificate is granted subject to the conditions as set out in IECEx Scheme
Rules, IECEx 02 and Operational Documents as amended

STANDARDS :
The equipment and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found
to comply with the following standards

IEC 60079-0:2017 Explosive atmospheres - Part 0: Equipment - General requirements

Edition:7.0

IEC 60079-31:2013 Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
Edition:2

IEC 60079-7:2015 Explosive atmospheres – Part 7: Equipment protection by increased safety ''e''
Edition:5.0

This Certificate does not indicate compliance with safety and performance requirements
other than those expressly included in the Standards listed above.

TEST & ASSESSMENT REPORTS:

A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in:

Test Reports:
GB/BAS/ExTR14.0189/00 GB/BAS/ExTR17.0159/00 GB/BAS/ExTR18.0261/00
GB/BAS/ExTR20.0132/00

Quality Assessment Reports:

CN/CQM/QAR19.0003/00 GB/BAS/QAR07.0032/08 GB/BAS/QAR13.0006/04
GB/BAS/QAR13.0007/05
 IECEx Certificate
of Conformity
Certificate No.: IECEx BAS 14.0097X Page 3 of 5

Date of issue: 2020-10-12 Issue No: 3

EQUIPMENT:
Equipment and systems covered by this Certificate are as follows:

The W60 Range of Induction Motors has shaft centre heights ranging from 315 to 1000mm (and NEMA equivalent) and comprises cast iron or
fabricated mild steel frames for horizontal, or vertical, foot mounting. The range of motors can optionally be used as generators for the
production of electrical energy. The range covers 2 to 14 pole 3 phase windings for 50 or 60Hz and is designed for connection to supplies up
to 13.8kV (Ex "ec")/15kV (Ex "t") except when separately Ex certified items reduce the voltage rating. The motors are rated for duty type
S1,S2,S6 or S9 which does not include starting. The motors have a minimum ingress protection of IP20, which can be increased up to a
maximum IP66 depending on the specific heat exchange and arrangement of the motor shaft seal.

Motors with an IP20 rating are certified Ex nA Gc only (for Zone 2 use) and have a restriction on the intended location for installation. Please
refer to the specific conditions of the certificate.

Refer to the Annex to this certificate for the full description of the equipment.

SPECIFIC CONDITIONS OF USE: YES as shown below:

1. The T4/T3 internal and external temperature class and T125°C/T160°C external temperature classification does not include motor starting
or cover motors under duty cycle conditions other than type S1, S2, S6 and S9.

2. The installer must ensure that any equipment certified cable glands and stopping plugs fitted to the terminal boxes are suitably IECEx/ATEX
certified. Any unused cable entries must be fitted with IECEx/ATEX certified stopping plugs. When installed the cable gland or stopping plug
must maintain the marked IP rating of the enclosure.

3. All terminal nuts and screws, whether used or not, shall be correctly tightened.

4. When tightening supply connections care should be taken to maintain clearance distances.

5. On auxiliary terminals the conductor insulation shall extend to within 1mm of the terminal throat.

6. There shall be no loose conductor strands on any terminal.

7. The current transformer secondary terminals must not be left open circuit to avoid potential high voltages.

8. Motors designed for T4 and variable frequency drives are fitted with stator winding temperature detection devices that must be connected
to the motor control circuit. For other starting methods, the connection of the winding temperature detectors is optional. The stator RTDs and
thermistors can be connected via a standard industrial controller provided that the controller is located in a safe area.

9. Anti-condensation heaters shall not be energised when the machine is energised.

10. Where auxiliary apparatus is fitted that is not covered by this certificate the installer and/or user, as appropriate, must ensure that it is
suitable for the conditions of use and that it does not invalidate this certification.

11. When motors are fitted with the Iris Power terminal box they can only be marked for, and used in, Zone 2 Gas atmospheres.

12. When the motor is fitted with terminal boxes which contain surge arrestors, capacitors, insulators, current transformers and connector
pins, the motor shall be rated to ensure that the ambient temperature range of these parts is not exceeded.

13. When the machine is being used as an asynchronous generator precautions must be taken for start-up and operation to ensure the
requirements of the certification are met. Refer to the manufacturers Installation, Operation and Maintenance Manual for full details.

continued on Page 5.
 IECEx Certificate
of Conformity
Certificate No.: IECEx BAS 14.0097X Page 4 of 5

Date of issue: 2020-10-12 Issue No: 3

DETAILS OF CERTIFICATE CHANGES (for issues 1 and above)

Variation 3.1

To allow the introduction of a 315 frame size motor, and to allow this and previously certified motors to be vertically mounted.

Variation 3.2

To allow a T4 class for operation in zone A, in accordance with IEC 60034-1 for voltage and frequency.

Variation 3.3

Clarification of details regarding testing of the rotor temperature for T3 machines.

Variation 3.4

To allow to use of the same heat exchangers across the W60 and M line.

Variation 3.5

To allow the introduction of additional information on the main terminal box in relation to the insulators arrangements.

Variation 3.6

To allow an update of the nameplate drawings in relation to zone A voltage variations.

Variation 3.7

To allow an update to the insulator information based on previous testing.

Variation 3.8

To allow the inclusion of a metallic hose for terminal box and motor connection.

Variation 3.9

To allow the introduction of IP66 stopping plugs, adaptors and reducers

ExTR: GB/BAS/ExTR20.0132/00 File Reference: 19/0380

 IECEx Certificate
of Conformity
Certificate No.: IECEx BAS 14.0097X Page 5 of 5

Date of issue: 2020-10-12 Issue No: 3

Additional information:

SPECIFIC CONDITIONS OF USE (continued)

14. Ex nA machines rated for IP20 shall only be installed in locations providing adequate protection against the entry of solid foreign objects or
water capable of impairing the safety of the machine.

[Link] non-metallic drain or blank plugs are for one time use only, once removed they shall be replaced with a new device.

16. Auxiliary terminal boxes currently afforded certificate number IECEx BAS 16.0129U intended for Group IIC applications shall only be
cleaned with a damp cloth to avoid potential electrostatic charge generation.

17. Machines rated at 13.8kV are suitable for use in gas Group IIB only.

18. The paint coating of the motors in potentially explosive dust atmospheres may present an electrostatic charging hazard - see the
manufacturer’s instructions for further information.

Annex:

IECEx BAS 14.0097X Annex [Link]

 SGS Baseefa Limited
Rockhead Business Park
Staden lane, Buxton, Derbyshire
SK17 9RZ
United Kingdom

ANNEX to IECEx BAS 14.0097X Issue No. 3 Date: 30 September 2020

The W60 Range of Induction Motors has shaft centre heights ranging from 315 to 1000mm (and NEMA equivalent) and comprises cast
iron or fabricated mild steel frames for horizontal or vertical mounting. The range of motors can optionally be used as generators for the
production of electrical energy. The range covers 2 to 14 pole 3 phase windings for 50 or 60Hz and is designed for connection to supplies
up to 13.8kV (Ex “ec”) / 15kV (Ex “t”) except when separately Ex certified items reduce the voltage rating. The motors are rated for duty
type S1, S2, S6 or S9 which does not include starting. The motors have a minimum ingress protection of IP20, which can be increased up
to a maximum IP66 depending on the specific heat exchange and arrangement of the motor shaft seal.
Motors with an IP20 rating are certified Ex ec Gc only (for Zone 2 use) and have a restriction on the intended location for installation. Please
refer to the specific conditions of the certificate.
Bearing Arrangements
Spigot housings are machined at either end of the stator frame into which the machined spigots of cast iron or fabricated steel end frames
are fitted. The end shields at the Drive End and Non-Drive End carry the bearing arrangements which may be ball, roller or sleeve and be
grease or oil lubricated. Optionally the motor can be arranged with just one bearing at the Non-Drive End (single bearing motor). Optional
bearing insulation is available and the bearing housings may be cast or fabricated. The bearing housings provide a degree of protection
of at least IP55 for equipment Group II, and IP55 for equipment Group IIIB (EPL Dc) and IP65 for equipment Group IIIC (EPL Db).
Stator
The stator core packs are built from insulated steel laminations which are clamped together by 6 to 12 bars for machines 560 and below
and which are welded and have clamping rings for machines size 630 and above. The wound and impregnated stator assembly is secured
in the stator frame by an interference fit and rotation is further prevented by the use of dowels.
Rotor
The rotor core packs which are built from insulated steel laminations are keyed and/or assembled by interference onto the steel shaft,
located at one end by a shoulder and at the other by a circlip or by circlips on both sides of the shaft. The laminations may be drilled to
allow for radial and/or axial cooling air circulation. The rotor cage is either cast aluminium or built up from copper, aluminium or brass bars.
When a built up rotor is used the copper, brass or aluminium bars are forced into the slots to give an interference fit and end rings are
brazed to the bars.
Balancing of the rotor is achieved either by fixing washers to cast studs on the aluminium rotors only or by fastening washers to the end
rings.
Terminal Boxes
The motors are fitted with separate bolt-on terminal boxes which are manufactured from cast iron or steel and fitted with bolt-on covers
incorporating a gasket which is glued to one surface. Component certified terminal boxes can also be fitted when applicable, as detailed in
the general remarks on this report.
Main terminal boxes may contain insulators, copper bars, current transformers ([Link]), surge arrestors and capacitors to form single or
double cable arrangements of air insulated and phase segregated versions. Neutral connections may also be included as part of the main
terminal box or as a separate unit.
Auxiliary terminal boxes contain IECEx component certified terminals, as detailed below;

Manufacturer Type of terminal Certificate number

ST 1,5 / 2,5; STTB 1,5 / IECEx KEM 06.0051U

2,5

USLKG series IECEx KEM 06.0035U

ST 4; STTB 4; ST 6 IECEx KEM 06.0050U

Phoenix Contact

ST 10; ST 16; ST 35 IECEx KEM 06.0033U

MBK 3; MBK 6; MSLKG 6 IECEx KEM 07.0008U

UT series IECEx KEM 06.0027U

Page 1 of 6

Document number: BAS-IECEx-003 Approved by: M Powney/R S Sinclair

Issue 1 Date: 22/8/19
 SGS Baseefa Limited
Rockhead Business Park
Staden lane, Buxton, Derbyshire
SK17 9RZ
United Kingdom

ANNEX to IECEx BAS 14.0097X Issue No. 3 Date: 30 September 2020

UK series IECEx KEM 06.0029U

UK 1,5N; UK 2.5; 3N; 5N; IECEx KEM 06.0034U

6N

MSLKG 2,5 IECEx KEM 07.0017U

UT series IECEx KEM 06.0013U

WDK 2.5 / 4; WDU 1.5 / 2.5 IECEx ULD 05.0008U

ZDU / ZPE / ZDK series IECEx ULD 05.0009U

WEIDMÜLLER SAK ; EK series IECEx KEM 06.0014U

ZDU ; ZPE series IECEx ULD 05.0009U

WDU / WPE series IECEx ULD 14.0005U

BTWP*; BTWP*T IECEx FTZU 12.0005U

WEG Drives & BTWI*; BTWI*T IECEx FTZU 12.0006U

Controls

BWTI 6; BWTI 10; BWTI IECEx FTZU 12.0007U

6T; BETI 10T

TB MVK ...; TB PIK …; TB IECEx FTZU 10.0011U

PYK …; TB PUK

TB MYK* ; TB MYPK*; TB IECEx FTZU 11.0006U

MYSK*; TB PYK*; TB
WGO*; TB AVK*; TB PIK*;
TB PEK*
KLEMSAN

AVK*; AVKY*; PYK*; IECEx FTZU 16.0003U

PYKM*; PYKMR 2,5; PIK*;
WGO*; WGL 1; WGO PB
6; PB*

TB AVK ... IECEx FTZU 10.0012U

WIELAND WT series IECEx SEV 14.0004U

Page 2 of 6

Document number: BAS-IECEx-003 Approved by: M Powney/R S Sinclair

Issue 1 Date: 22/8/19
 SGS Baseefa Limited
Rockhead Business Park
Staden lane, Buxton, Derbyshire
SK17 9RZ
United Kingdom

ANNEX to IECEx BAS 14.0097X Issue No. 3 Date: 30 September 2020

WKN series IECEx SEV 15.0002U

CTS, CMT, CMB, CMC, IECEx SIR 16.0056U

CDL, ODL, CTL, CSC,
CGM, CGT, PTB, AS,
ADL, AGT

CTS, PTB, CDL, ODL, IECEx UL 11.0053U

CTL, CSC, CGT, CGM,
CONNECTWELL CGT, CMT, CMB, CMC

AS, AGT, ADL IECEx UL 11.0044U

CX, CM, CSB, CBS, STH, IECEx SIR 16.0016U

CDL

The following IECEx component certified enclosures can also be used;

Manufacturer Type of terminal box Certificate Number(s)

Quartzelec Limited PSE Phase Segregated IECEx SIR 10.0147U

Type 8150/0-****-****-***-
IECEx PTB 09.0047U
****

[Link]
Type 8146/-***-** IECEx PTB 06.0044U

Type 8125/-***-*** IECEx PTB 06.0029U

Type 07-56.1-…./…. IECEx IBE 09.0016U

Type 07-5180****/**** IECEx PTB 11.0032U

Bartec

Type 07-5184-****/****
IECEx PTB 09.0008U
and 07-5185-****/****

WPS, WPI, WBT, WBL,

WEG IECEx BAS 14.0175U
WAI, WNT
EQUIPAMENTOS
ELÉTRICOS S/A
WATB Series IECEx BAS 16.0129U

Any size of terminal box can be fitted to any of the frame sizes within the range as long as they are suitably rated for their intended use
and it is physically possible to do so. The terminal boxes may also be fitted with optional IECEx equipment certified parts, which do not
form part of this assessment.

Ventilation

Page 3 of 6

Document number: BAS-IECEx-003 Approved by: M Powney/R S Sinclair

Issue 1 Date: 22/8/19
 SGS Baseefa Limited
Rockhead Business Park
Staden lane, Buxton, Derbyshire
SK17 9RZ
United Kingdom

ANNEX to IECEx BAS 14.0097X Issue No. 3 Date: 30 September 2020

Various methods of cooling are used including louvered open air to air, externally ventilated or totally enclosed versions of air to air or air
to water, with or without silencing. In addition, forced ventilation may be used with separately IECEx certified motors and optionally an
IECEx certified encoder or brake may be attached to the main motor shaft.

External fans when used are manufactured from cast iron, welded steel or aluminium containing less than 6% magnesium.

Windings

Low voltage motors are wound using polyester-imide enamel wire with the overhangs suitably insulated and tied with fibreglass. High
voltage motors are wound using either enamelled copper wire with a polyester and glass fibre covering or bare wire with two layers of
special mica tape.

Motors with rated voltages above 4160V have tape applied to protect against corona effects and also have stress relief tape applied. After
winding, the high voltage motors are vacuum impregnated with a bi-component epoxy resin.

Use of Variable Voltage Variable Frequency Drives

The range of W60 motors can be operated with frequency inverters (variable speed drives) in the following conditions:

The range of M-Line motors can be operated with frequency inverters (variable speed drives) in the following conditions/considerations:

- With PWM variable frequency drives, up to 13800 V, insulation system F (or H), are able to operate within their insulation class
limit, respecting the motor temperature class.

- With forced ventilation (independent cooling system) or oversizing, shall be applied in accordance with the application
characteristics due on variation of nominal frequency.

- With safety thermal margin or power derating to operate within insulation class limit B.

- With variable frequency drives with sinusoidal output signal (equipment able to supply motor voltage and current with negligible
harmonic content), or variable frequency drives type PWM fitted with sinusoidal filters in the output. In this condition it is not
expected significant additional temperature rise (over than 10K), beyond the normally shown by the motor under sinusoidal
supply.

- With variable frequency drives that supply motor voltage / current with greater harmonic distortion, may resulting in additional
heating over than 10K. This situation is usually to occur with higher power machines and low voltage (<1000V) and the motor
should be designed properly.

- Oversizing insulation of motors operating with variable frequency drives can be necessary depending on the application
characteristics and variable frequency drive.

- Use of variable frequency drives that supply PWM voltage with presence of common mode components (zero sequence) require
motor insulation oversizing for voltage higher than 4000V.

- Speed x torque curves for motor shall be supplied for application with a variable frequency drives.

Motors shall be fitted with thermal protective devices which shall be connected into the motor control circuit in order to keep T3 or T4
temperature class and or T125°C or T160°C surface temperature for
dust applications. Reenergizing must not be automatic.

Auxiliaries

The auxiliaries which may be fitted to this range of machine are:-

 Vibration monitoring sensors.

 Winding, bearing, air/water temperature detectors comprising RTD's, thermocouples, thermistors or thermostats. Refer to the
general remarks for further details.

 Anti-condensation heaters.

The following IECEx certified components can be used with the machine;

Page 4 of 6

Document number: BAS-IECEx-003 Approved by: M Powney/R S Sinclair

Issue 1 Date: 22/8/19
 SGS Baseefa Limited
Rockhead Business Park
Staden lane, Buxton, Derbyshire
SK17 9RZ
United Kingdom

ANNEX to IECEx BAS 14.0097X Issue No. 3 Date: 30 September 2020

Manufacturer Type of accessory Certificate Number(s)

RSV Anti-condensation
Flexelec SA IECEx SIR 10.0151U
heater

Self-Limiting Heating
BARTEC GmbH IECEx KEM 07.0048U
Cable Series HSB

Resistance Temperature
Minco Products Inc. IECEx DEK 12.0057U
Detector

Temperature Sensor
EPHY-MESS GmbH IECEx IBE 14.0058U
PR-SPA-EX-***

Current Transformer
F.T.M. Srl IECEx CES 13.0015U
Series AOC Ex

Control Unit
IECEx BVS 07.0029U
Type 8510/1
[Link]
Circuit Breaker
IECEX PTB 06.0062U
Type 8562/5

Temperature
Rosemount IECEx BAS 12.0070U
Transmitter Model 644

Control Module
IECEx PTB 11.0083 U
Type 07-7311
Bartec
Control Module
IECEx PTB 11.0082 U
Type 07-7331

Stator Winding
Temperature Detectors IECEx PRE 18.0032U
(Types - TSR,,)

Techno Controls TSR* series slot

resistance thermometer
and TBTD-* series IECEx SIR 16.0033U
bearing temperature
detectors

Note: In the situation where motors are fitted with IECEx equipment certified T4 anti-condensation heaters the overall motor temperature
class marking can be T4. Any relevant specific conditions of use relating to the use of the heaters as part of the motor must be complied
with.

Type Testing

Each motor design shall be subject to a WEG test procedure for Ex ec motors:
 Motor with temperature class T3: motor design verification by thermal test without measurement of rotor temperature
 Motor with temperature class T4: motor design verification by thermal test with measurement of rotor temperature
Slight variations in motor design already tested can have the temperature class re-verified by calculation.

Page 5 of 6

Document number: BAS-IECEx-003 Approved by: M Powney/R S Sinclair

Issue 1 Date: 22/8/19
 SGS Baseefa Limited
Rockhead Business Park
Staden lane, Buxton, Derbyshire
SK17 9RZ
United Kingdom

ANNEX to IECEx BAS 14.0097X Issue No. 3 Date: 30 September 2020

Ambient Temperatures

The standard temperature range of the motors is -20°C to +40°C. By the choice of suitable materials and use of the de-rating data called
up on the drawings an ambient range of -55°C to +60°C may be achieved. Individual motors must be marked according to the build of
the unit.

Ingress Protection Rating

The ingress protection rating of the motors, other than the open air to air ventilation type, can be increased depending on the shaft seal
used:

Shaft seal IP rating

Oil IP55 to IP66
Taconite labyrinth IP55 to IP65
Taconite labyrinth with
IP55 to IP66
Teflon seal
Labyrinth Oil-Mist /
IP55 to IP66
Grease (Inproseal)
Flange/Sleeve Bearing IP55 to IP66

Page 6 of 6

Document number: BAS-IECEx-003 Approved by: M Powney/R S Sinclair

Issue 1 Date: 22/8/19