Scribd
Upload
148 views4 pages

Arduino Propeller LED Clock Project

This Arduino code defines an analog clock with 16 LEDs. It initializes the LED pins and a sensor pin in setup. The main loop function continuously updates the time, draws the hands and markers for the hours, minutes and seconds at the appropriate LEDs, and clears the display between updates. Functions are defined to draw each component of the clock display to the LEDs.

Uploaded by

Jeng Raffa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
148 views4 pages

Arduino Propeller LED Clock Project

This Arduino code defines an analog clock with 16 LEDs. It initializes the LED pins and a sensor pin in setup. The main loop function continuously updates the time, draws the hands and markers for the hours, minutes and seconds at the appropriate LEDs, and clears the display between updates. Functions are defined to draw each component of the clock display to the LEDs.

Uploaded by

Jeng Raffa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

// hobbyprojects

// ArduinoNanoPropellerLEDAnalogClock20190403A

int LED1 = 2;
int LED2 = 3;
int LED3 = 4;
int LED4 = 5;
int LED5 = 6;
int LED6 = 7;
int LED7 = 8;
int LED8 = 9;
int LED9 = 10;
int LED10 = 11;
int LED11 = 12;
int LED12 = A1;
int LED13 = A2;
int LED14 = A3;
int LED15 = A4;
int LED16 = A5;

int sensorPin = A0;

unsigned int n,ADCvalue,propeller_posn;


unsigned long previousTime = 0;

byte hours = 12; // set hours


byte minutes = 15; // set minutes
byte seconds = 00; // set seconds

int val;

void setup()
{
pinMode(LED1,OUTPUT);
pinMode(LED2,OUTPUT);
pinMode(LED3,OUTPUT);
pinMode(LED4,OUTPUT);
pinMode(LED5,OUTPUT);
pinMode(LED6,OUTPUT);
pinMode(LED7,OUTPUT);
pinMode(LED8,OUTPUT);
pinMode(LED9,OUTPUT);
pinMode(LED10,OUTPUT);
pinMode(LED11,OUTPUT);
pinMode(LED12,OUTPUT);
pinMode(LED13,OUTPUT);
pinMode(LED14,OUTPUT);
pinMode(LED15,OUTPUT);
pinMode(LED16,OUTPUT);

pinMode(sensorPin,INPUT_PULLUP);

if(hours == 12)
hours = 0;
}

void loop()
{
val = digitalRead(sensorPin);

while (val == LOW)


{
val = digitalRead(sensorPin);
}

if (millis() >= (previousTime))


{
previousTime = previousTime + 1000;
seconds = seconds+1;
if (seconds == 60)
{
seconds = 0;
minutes = minutes+1;
}
if (minutes == 60)
{
minutes = 0;
hours = hours+1;
}
if (hours == 12)
{
hours = 0;
}
}

propeller_posn=30;
n=0;

while(n < 60)


{

drawMinuteMarker();

if ((propeller_posn==0) || (propeller_posn==5) || (propeller_posn==10) ||


(propeller_posn==15) || (propeller_posn==20) || (propeller_posn==25) ||
(propeller_posn==30) || (propeller_posn==35) || (propeller_posn==40) ||
(propeller_posn==45) || (propeller_posn==50) || (propeller_posn==55))
drawHourMarker();

if ((propeller_posn==0) || (propeller_posn==15) || (propeller_posn==30) ||


(propeller_posn==45))
drawQuarterMarker();

if((propeller_posn == hours*5) || (( propeller_posn == 0 ) && (hours == 0)))


drawHoursHand();

if(propeller_posn == minutes)
drawMinutesHand();

if(propeller_posn == seconds)
drawSecondsHand();
delayMicroseconds(140); // for LED pixel width (change the value
according to motor speed. Increase for low speed, decrease for high speed
motor)

displayClear();

drawInner_Circle();

delayMicroseconds(600); // for the gap between LED pixels/minutes markers


(change the value according to motor speed. Increase for low speed, decrease
for high speed motor)

n++;
propeller_posn++;
if(propeller_posn == 60)
propeller_posn=0;
}

val = digitalRead(sensorPin);

while (val == HIGH)


{
val = digitalRead(sensorPin);
}
}

//=========================

void displayClear()
{
digitalWrite(LED1,LOW);
digitalWrite(LED2,LOW);
digitalWrite(LED3,LOW);
digitalWrite(LED4,LOW);
digitalWrite(LED5,LOW);
digitalWrite(LED6,LOW);
digitalWrite(LED7,LOW);
digitalWrite(LED8,LOW);
digitalWrite(LED9,LOW);
digitalWrite(LED10,LOW);
digitalWrite(LED11,LOW);
digitalWrite(LED12,LOW);
digitalWrite(LED13,LOW);
digitalWrite(LED14,LOW);
digitalWrite(LED15,LOW);
digitalWrite(LED16,LOW);
}

void drawMinuteMarker()
{
digitalWrite(LED16,HIGH);
}

void drawHourMarker()
{
digitalWrite(LED15,HIGH);
digitalWrite(LED14,HIGH);
}

void drawQuarterMarker()
{
digitalWrite(LED13,HIGH);
digitalWrite(LED12,HIGH);
}

void drawHoursHand()
{
digitalWrite(LED1,HIGH);
digitalWrite(LED2,HIGH);
digitalWrite(LED3,HIGH);
digitalWrite(LED4,HIGH);
digitalWrite(LED5,HIGH);
digitalWrite(LED6,HIGH);
digitalWrite(LED7,HIGH);
}

void drawMinutesHand()
{
digitalWrite(LED1,HIGH);
digitalWrite(LED2,HIGH);
digitalWrite(LED3,HIGH);
digitalWrite(LED4,HIGH);
digitalWrite(LED5,HIGH);
digitalWrite(LED6,HIGH);
digitalWrite(LED7,HIGH);
digitalWrite(LED8,HIGH);
digitalWrite(LED9,HIGH);
}

void drawSecondsHand()
{
digitalWrite(LED1,HIGH);
digitalWrite(LED2,HIGH);
digitalWrite(LED3,HIGH);
digitalWrite(LED4,HIGH);
digitalWrite(LED5,HIGH);
digitalWrite(LED6,HIGH);
digitalWrite(LED7,HIGH);
digitalWrite(LED8,HIGH);
digitalWrite(LED9,HIGH);
digitalWrite(LED10,HIGH);
digitalWrite(LED11,HIGH);
}

void drawInner_Circle()
{
digitalWrite(LED1,HIGH);
delayMicroseconds(30);
digitalWrite(LED1,LOW);
}

You might also like