B.
Sc (H) Electronic Sciences, VI Sem
PHOTONICS
(UPC : 32511603)
TOPIC
Light Emitting Diodes : Working Principle, Construction and Application
Light Emitting Diodes : Working Principle, Construction and Application
LED (Light Emitting Diode) is an optoelectronic device which works on the principle
of electro-luminance. Electro-luminance is the property of the material to convert
electrical energy into light energy.
It is specially doped p-n junction diode made up of specific type of semiconductors.
When the light emitting diode light is forward biased, then it emits light either in
visible region or infra red region.
Working Principle of LED
The light emitting diode works like a normal PN-junction diode. When the diode is
forward biased, then the current flows through the diode.The flow of current in the
semiconductors is caused by the both flow of holes in the opposite direction of
current and flow of electrons in the direction of the current. Hence there will be
recombination due to the flow of these charge carriers.
The recombination indicates that the electrons in the conduction band jump down
to the valence band. When the electrons jump from one band to another band the
electrons will emit the electromagnetic energy in the form of photons and the
photon energy is equal to the forbidden energy gap (Eg).
Eg = hf
Where h is known as a Planck constant, and f is the frequency of the emitted
electromagnetic radiation.
The frequency of radiation is related to the velocity of light as a
f= c / λ. where c is the speed of light λ is denoted as a wavelength of an
electromagnetic radiation and the above equation will become as
Eg = hc / λ
From the above equation, we can say that the wavelength of electromagnetic
radiation is inversely proportional to the forbidden gap.
For LED the wavelength of the emitted photon, lies in the visible or infrared region.
I-V Characteristics of LED
There are different types of light emitting diodes are available in the market and
there are different LED characteristics which include the color light, or wavelength
radiation, light intensity. The important characteristic of the LED is color.
The following graph shows the approximate curves between the forward voltage and
the current. Each curve in the graph indicates the different color.
The safe forward voltage ratings of most LEDs is from 1V to 3 V and forward current
ratings is from 200 mA to 100 mA.
Light emitting diodes emit either visible light or invisible infrared light when forward
biased. The LEDs which emit invisible infrared light are used for remote controls.
Materials Used in LEDS
Silicon or germanium diodes do not emit energy in the form of light. Instead, they
emit energy in the form of heat. Thus, silicon or germanium is not used for
constructing LEDs.
In general for silicon and germanium semiconductors, this forbidden energy gap
between the condition and valence bands are such that the total radiation of
electromagnetic wave during recombination is in the form of the infrared radiation.
The material in an LED is selected in such a way that the wavelength of the released
photons falls within the visible portion of the light spectrum.
Visible LED is a type of LED that emits visible light. These LEDs are mainly used for
display or illumination. Invisible LED is a type of LED that emits invisible light
(infrared light). These LEDs are mainly used with photosensors such as photodiodes.
Some commonly used LEDs are mentioned below.
Gallium Arsenide (GaAs) – infra-red
Gallium Arsenide Phosphide (GaAsP) – red to infra-red, orange
Aluminium Gallium Arsenide Phosphide (AlGaAsP) – high-brightness red,
orange-red, orange, and yellow
Gallium Phosphide (GaP) – red, yellow and green
Aluminium Gallium Phosphide (AlGaP) – green
Gallium Nitride (GaN) – green, emerald green
Gallium Indium Nitride (GaInN) – near ultraviolet, bluish-green and blue
Silicon Carbide (SiC) – blue as a substrate
Zinc Selenide (ZnSe) – blue
Aluminium Gallium Nitride (AlGaN) – ultraviolet
Construction:
1. The methods used to construct LED are to deposit three semiconductor
layers on the substrate.
2. The three semiconductor layers deposited on the substrate are n-type
semiconductor, p-type semiconductor and active region.
3. Active region is present in between the n-type and p-type semiconductor
layers.
4. When LED is forward biased, free electrons from n-type semiconductor and
holes from p-type semiconductor are pushed towards the active region.
1. When free electrons from n-side and holes from p-side recombine with the
opposite charge carriers (free electrons with holes or holes with free
electrons) in active region, an invisible or visible light is emitted.
2. In LED, most of the charge carriers recombine at active region. Therefore,
most of the light is emitted by the active region. The active region is also
called as depletion region.
Advantages of LED
1. Light emitting diodes consume low energy.
2. LEDs are very cheap and readily available.
3. LEDs are light in weight.
4. Smaller size.
5. LEDs have longer lifetime.
6. LEDs operates very fast. They can be turned on and off in very less time.
7. LEDs do not contain toxic material like mercury which is used in fluorescent
lamps.
8. LEDs of different colors of light are available.
9. The brightness of light emitted by LED is depends on the current flow, thus
the brightness of LED can be easily controlled by varying the current.
Disadvantages of LED
1. LEDs need more power to operate than normal p-n junction diodes.
2. Luminous efficiency of LEDs is low.
Applications of LED
The various applications of LEDs are as follows
1. LED is used as a bulb in the homes and industries
2. Burglar alarms systems
3. Calculators
4. Picture phones
5. Traffic signals
6. Digital computers
7. Multimeters
8. Microprocessors
9. Digital watches
Internal Quantum Efficiency of the LED
The fraction of the electrons that are injected into the depletion layer which results
in photons getting produced is known as internal quantum efficiency of the LED. It is
denoted as η.
If N is the number of electrons injected into the depletion layer every second, the
power output of the device is expressed by,
P = η*N*h*v = η*I*h*v/e
Where,
I is forward current
e is the electronic charge
Although internal quantum efficiences of some LED Materials is very high, the
external efficiences are much lower.
External Quantum Efficiency (EQE)
The ratio of the number of photons emitted from the LED to the number of electrons
passing through the device - in other words, how efficiently the device coverts
electrons to photons and allows them to escape.
