Scribd
Upload
161 views2 pages

IEC Assignment 1 Final Fall 2023 24

This document contains an assignment for an Introduction to Electrical Circuits course. It provides instructions for 5 problems related to circuit analysis using variables based on the student's ID number. The cover page format is specified. The problems involve calculating impedance, reactance, current, power, power factor, and drawing diagrams for series RLC circuits and parallel branch circuits. Students are to submit handwritten solutions by a specified deadline.

Uploaded by

tahmidomit0
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
161 views2 pages

IEC Assignment 1 Final Fall 2023 24

This document contains an assignment for an Introduction to Electrical Circuits course. It provides instructions for 5 problems related to circuit analysis using variables based on the student's ID number. The cover page format is specified. The problems involve calculating impedance, reactance, current, power, power factor, and drawing diagrams for series RLC circuits and parallel branch circuits. Students are to submit handwritten solutions by a specified deadline.

Uploaded by

tahmidomit0
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

American International University- Bangladesh (AIUB)

Faculty of Engineering
Assignment-1 [Section: R] [Final term]
Course Name: Introduction to Electrical Circuits Course Code: EEE 2109
Faculty Name: Mohammad Mostafizur Rahman
Semester: Fall 2023-24
Submission Date: 24/12/2023

Student Name: Tahmid Shah Student ID: 22-47488-2


Department: CSE Section: R

Marking (to be filled by Faculty):

Problem 1
Problem 2
Problem 3
Problem 4
Problem 5
Comments: Total Marks (Out of 20):

Instruction Related to Used Variables:


Note that this assignment uses the variables m1, m2, m3, m4, and m5, which are the five digits of middle of your student
ID. For example, if your student ID is: 09-15985-3, then you must consider: m1=1; m2=5; m3=9; m4=8; m5=5
Write in the following Table the variables value according to your ID:
m1 m2 m3 m4 m5

4 7 4 8 8

File Name: IEC_L_Assignment-1_Final _YourID_Your Full Name (AIUB Format)

With the solution of given problems add this page as cover page and the answer should be hand written.
Assignment Questions (Answer all the Questions)
Submission Deadline (Revised): On or before 06/12/2021
1. A series circuit consist of R = 2000 ohms, L = (0.056 + 5×m5) henry (H), C = (40 + 0.5×m5) micro-farad (μF)
and the applied voltage v = Vm sin (377t +0) V [Vm = (280 + (3 × m4) + (5 × m5)]: (i) Draw the circuit diagram,
(ii) Calculate the inductive reactance, the capacitive reactance, and the impedance. (iii) Draw the impedance
diagram. (iv) Calculate the current, the voltage drops across the resistor, the inductor and the capacitor. (v) Verify
the KVL. (vi) Calculate the power factor and reactive factor, the power, reactive power, apparent power. (iv)
Draw the power triangle.
2. For the following circuits: Calculate the total impedance, I, I1, I2, VC. Calculate power supplied by source.
Where, E = [80 + (2×m4) + (4×m5)] V [Fix from your ID]

Figure for question no. 2

3. For the following circuit diagram:


(a) Calculate (i) the total admittance and impedance, (ii) the currents I, IR, and IL.
(b) Calculate (i) the power factor and reactive factor (ii) the apparent power, real power and
reactive power.
(c) Draw the admittance diagram, phasor or vector diagram and power triangle.
The value (magnitude) of V= 80 + 2× m4 + 4× m5 (Calculate the value of V from your ID)

Figure for question no. 2

You might also like